01707 280 050 SALES @ E-SERVICE.CO.UK WWW.E-SERVICE.CO.

UK

Nayax installation Guidelines

Subtitle
 Nayax Installation Guidlines

7
9

2
5
3
6

Figure 1

2
 Nayax Installation Guidlines

1 Nayax VPOS 6 PL2 Wire Holes

This is the wireless card reader. The VPOS should The PL2 wire holes are used to connect the inter-
be fixed to the outside of the machine in easy face board to the AMIT and number meter.
access to customers. For detailed information on If manually connecting the I/O cable or number
fitting the VPOS unit, please refer to page XXXXX. meter to interface board, detailed instructions can
be found on page XXXXXX.

2 Nayax AMIT 3
The Nayax AMIT 3 is the central unit of the Nayax 7 PL1 Main Board Cable
system and connects the Nayax components This cable is attached to the machine’s main board
together. The AMIT 3 should be placed inside the and is usually connected directly to the coin mech.
machine In the Nayax setup, the cable is plugged into the
interface board’s PL1 pin-socket.

3 RJ45 / RJ6 Connector Cable

This cable connects the external VPOS to the
8 Number Meter
internal AMIT 3. The cable must pass through hole
This number meter attaches to the interface board
made while fitting the VPOS.
and records when a transaction is used. For detailed
For detailed information on fitting the VPOS unit,
instructions for manually attaching a number meter
please refer to page XXXXX.
to the interface board, please refer to page XXXXX.

4 I/O Connector Cable

This cable plugs into the AMIT’s ‘I/O‘ socket and 9 Antenna
connects it to the Nayax Interface Board. Please The antenna screws into the top of the AMIT3 and

note that the cable splits to include a plug that is can positioned internally to protect against vandal-

not used in most installations. ism or externally to maximise signal strength.

5 NAYAX Interface Board

This small circuit board plugs into the coin mech
through the socket that is usually connected to the
machine’s main control board. It connects the Amit
to the coin mech, number meter and main board.

3
 Nayax Installation Guidlines

VPOS to Interface Board wiring guide

PL2

1
2
3
4
5
6
7
8
9
10
11
12

Figure 2

Wire Colour Wire Name PL2 Hole Number

Brown AC / DC + 3

Orange PULSE1\FUJI RXD 4

Blue EX PULSE INHIBIT 5

Green AC / DC - 7

Red GND 8

Yellow PULSE2\FUJI TXD Not used

Black VCC Not used

To correctly wire the Nayax Interface Board, please follow the diagram above to
match the correct wires to the correct holes.

4
 Nayax Installation Guidlines

Number meter wiring guide

Figure 3

To correctly wire the number meter, please follow the diagram above to match the
correct wires to the correct holes.

5
 Nayax Installation Guidlines

Thomas software updating guide

Figure 4

1. Access the Control Module

Open the Machine and locate the Control Module, as seen in figure 4. Remove the bill validator to gain
access to the control module and open it’s hinged door.

Figure 6

Figure 5

2. Replace the software chip

Remove the chip from the inside of the control module’s door, as seen circled in red in figure 5.
Replace the old chip with the new software chip provided in the upgrade kit.

6
 Nayax Installation Guidlines

Figure 8

Figure 7

3. Enable 10p coins for testing

On the large circuit board on the opposite side, locate the four switches marked ‘S2’, as seen circled
in red in figure 7. Flip the fourth switch to the on possition, as seen in figure 8.

4. Test the newly activated software.

Test the software by dropping a 10p coin, it should give change for the same value that the Nayax tap
value should be, i.e £5, £10 or £20. Insert all other coins and notes and check the change given is correct.

If the change given is correct, close the control module, re-insert the note validator amd proceed to
section 5. If the change is incorrect or you encounter other errors, replace the old software and call
E-Service support on 01707 280 050.

7
 Nayax Installation Guidlines

Figure 9

Figure 10

5. Remove the plastic cover from the Thomas Machine door

Unscrew the four 7mm nuts as that are circled in red in figure 9. Once the nuts are unscrewed, remove the
plastic cover, as seen in figure 10.

8
 Nayax Installation Guidlines

VPOS wireless card reader mounting guide

Figure 12

Figure 11 Figure 13

1. Place the provided template over the Thomas 3000

Print out the template on last page in this guide and place it over the Thomas machine, aligning the yellow
arrow with the indent corner as seen in figure 12.

CAUTION: Remeber to print without scaling the page and use the printed ruler to
ensure that the printout is correctly sized.

2. Drill through the faceplate as marked on the printed guide

Use a center punch to mark the five points to drill as marked on the guide.
Drill four 6mm holes for the screws and one 22mm hole for the cable to pass though.

Optionally, you may remove the inner back plate and shorten it to the red line, rather than drilling though it.
Take care to remove the circuite board on the right of figure 13 before removing the plate.

9
 Nayax Installation Guidlines

Figure 14

3. Insert the grommet for the connector cable

Once drilled, fit the grommet into the 22mm hole, as seen in figure 14.

Figure 15 Figure 16

4. Screw the VPOS into the front of the machine

Position the VPOS wireless card reader over the newly drilled holes and screw it in from the back of the

machine’s door, as seen in figure 16. Ensure that the card reader is flush with the machine and correctly

aligned before tightening the screws.

10
 Nayax Installation Guidlines

AMIT 3 mounting guide

Figure 17 Figure 18

6. Position the AMIT 3 inside the machine and connect it to the VPOS
Place the AMIT inside the machine, using its magnetic back to attach it to a metal surface. Next, plug the
VPOS’s connection cable into the AMIT port marked ‘VPOS’, as in figure 18.

Figure 19 Figure 20

7. Connect the Nayax Interface Board to the AMIT 3

Plug the the I/O cable into the AMIT’s port marked ‘I/O’, as seen in figure 20.
If the Interface Board is not already connected to the I/O cable, please refer to page 4 for detailed
instructions on how to wire them together.

11
 Nayax Installation Guidlines

NAYAX Interface Board mounting guide

Figure 22

Figure 23
Figure 21

8. Plug the Interface Board into the coin mech and the main board
Find the cable connecting the machine’s main controle board to the coin mech and unplug it. Plug the
interface board into the same socket as in figure 22.

Take the ribbon cable that you just unplugged and plug it into the Interface Board.
IMPORTANT: skip the first pin when pluggin in the ribbon cable, as in figure 23.

12
 Nayax Installation Guidlines

Mounting the aerial guide

Figure 24 Figure 25

5. Position the aerial on the machine.

Position aerial on the machine. Positioning the aerial on the inside of the machine will protect against
vandelism, but positioning the aerial externally will maximise signal strength. To position the aerial on the

outside, pass its wire into the hole on the back of the machin, as in figure 24.

6. Screw the aerial cable into the AMIT 3 unit.

Find the copper end of the aerial cable and screw it onto the top left of the AMIT unit, as in figure 25.

13
 Nayax Installation Guidlines

Finishing up the installation

Figure 26 Figure 27

9. Secure the loose wires

Using the sticky metal clamps included in the kit, tie down the loose cables into a preferred location,
as seen in n figure 26.

10. Position the number meter

Position the number meter (used to record transaction numbers) in a preferred visible location,
as seen in figure 27. If your Interface Board does not have already have a number meter attached, please
refer to page 5 for detailed instructions on how to wire them together.

11. Stick the contactless payment instruction label

Find the contactless payment instructions label that was included in the kit and attach it to the front of the
machine in a visible location.

12. Turn on the Machine and contact E-Service

Turn the power on to the machine and call E-Service on 01707 280 050. We will complete the installation

with you and test it remotely.

14
Nayax VPOS fitting guide

Print out this page on a sheet of A4 paper.

Remember to select “DO NOT SCALE” in your
printer’s settings

IMPORTANT: Use the printed ruler at the

bottom of the page to check that the guide
has printed at the correct size.

Cut out the guide along the dotted blue lines

and place it over the machine as seen on
page XXXX

Use a center punch to mark the five points to

drill as marked on the guide.

Drill four 6mm holes for the screws and one

22mm hole for the cable to pass though.