Scribd
Upload
30 views

RC EXAM ELEC10 Electronic Devices and Circuits LC Circuits

The maximum possible collector circuit efficiency of an ideal class A power amplifier is 50%. When a switching voltage regulator is used, it can be either a step-up or step-down regulator. The overall bandwidth of two identical voltage amplifiers connected in cascade will be worse than that of a single stage.

Uploaded by

aljamier
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
30 views

RC EXAM ELEC10 Electronic Devices and Circuits LC Circuits

The maximum possible collector circuit efficiency of an ideal class A power amplifier is 50%. When a switching voltage regulator is used, it can be either a step-up or step-down regulator. The overall bandwidth of two identical voltage amplifiers connected in cascade will be worse than that of a single stage.

Uploaded by

aljamier
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

RC EXAM ELEC10 9.

The maximum possible collector circuit


efficiency of an ideal class A power
1. Instrument used for dc measurement
amplifier is:
alone is:
50%
Permanent magnet type

10. If a d’ Arsonval meter movement is


2. If the feedback signal is returned to the
rated at 50 μA, and only 25 μA is
input in series with the applied voltage,
passing through its coil, the deflection
the input impedance ______.
is:
Increases
50 percent of full scale

3. The main characteristics of a


11. In an electronic power supply, larger
Darlington amplifier are:
the value of shunt capacitor filter, the
High input impedance, low output
________.
impedance and high current gain.
smaller the dc voltage across the
load
4. The following instrument should be
used to measure 600 kV ac voltage:
12. A switching voltage regulator can be
Electrostatic voltmeter
_____.
step-down
5. N-channel FETs are superior to P-
channel FETs, because:
13. The overall bandwidth of two identical
Mobility of electrons is greater than
voltage amplifiers connected in
that of holes.
cascade will:
Be worse than that of a single stage.
6. The type of power amplifier which
exhibits crossover distortion in its
14. The basic power supply is made up of
output is ____.
_______.
Class B
a rectifier, a filter and a regulator

7. Which of the following parameters is


15. In a full-wave bridge rectifier, the peak
used for distinguishing between a
inverse voltage (PIV) across a
small signal and a large-signal
nonconducting diode is approximately
amplifier?
equal to _______.
Bandwidth
the peak value of the secondary
voltage
8. A surge current is likely to flow when
the circuit is switched on. What is the
16. An ideal rectifier should have ______.
cause of surge current in a diode
100% efficiency, zero ripple factor,
rectifier with a capacitance input filter?
zero harmonic factor and unity
The capacitor acts as a short circuit
displacement factor
at the instant of switching.
17. When a sinusoidal voltage wave is fed
to a Schmitt trigger, the output will be:
asymmetric square wave.

18. What is the theoretical maximum


efficiency of a Bridge rectifier circuit?
81.2%

19. The large signal bandwidth of an op-


amp is limited by its:
Slew rate

20. An oscillator of the LC type that has a


split capacitor in the circuit is:
Colpitts oscillator

21. In a voltage shunt negative feedback


amplifier system, the input resistance
Ri and the output resistance Ro of the
basic amplifier are modified as follows:
Both Ri and Ro are decreased.

22. A magnetic field parallel to the x axis


with a magnitude that decreases with
increasing x but does not change with y
and z is impossible according to:
Gauss` law for magnetism

23. Electrostatic instrument uses the


principle of variation of:
Capacitance with voltage

24. In a clamping circuit, the peak-to-peak


voltage of the waveform being
clamped is:
not affected by the clamping

25. Difference between the indicated value


and the true value of a quantity is
known as:
Dynamic error

You might also like