0% found this document useful (0 votes)
10 views

Elec QC Syllabus

This document covers electrical concepts and components including voltage, current, resistance, frequency, power, transformers, motors, panel boards, switchgear, cables, meters, generators, capacitors, earthing, and relays. It also discusses designing electrical systems for various buildings like residential, commercial, and industrial structures.

Uploaded by

BINU P MATHEW
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
10 views

Elec QC Syllabus

This document covers electrical concepts and components including voltage, current, resistance, frequency, power, transformers, motors, panel boards, switchgear, cables, meters, generators, capacitors, earthing, and relays. It also discusses designing electrical systems for various buildings like residential, commercial, and industrial structures.

Uploaded by

BINU P MATHEW
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

INDUSTRIAL ELECTRICAL QC

Electricity and its basic parameters – Voltage, Current, Resistance, Frequency, Power,
Powerfactor

Electrical Power System – Generation, Transmission, Distribution, Star-Delta configuration,


Relation between Phase and Line Voltage and Current., Importance of Power factor.

Introduction to House wiring – Electrical standards to be followed in House wiring, Wiring


types, Electrical Subcircuits

Protective Devices- MCBs, ELCBs, RCCBs, RCBOs, Selection of Protective devices for
Light loads and Power loads, Selection of wires, Selection and wiring of Distribution boards,
Single line diagram for domestic installations.

 Electrical Design and Schematic diagram preparation for Residential Appartments.

Transformers – Construction and Working, Name plate specifications, Voltage ratio,


Capacity, Insulation and cooling type, Vector group, Tap changer
Selection of Transformers – Maximum demand, Demand factor& Diversity factor, Maximum
power rating of individual Transformers and Load that can be connected to 11 KV supply.

Motors – Induction motors, Synchronous motors, DC Motors, Construction and Working,


Selection of Switchgears for Motors, Different types of Starters, Selection of various Starters
for Motors, Variable Frequency Drive

Panel boards – Parts of a Panel board, Connection layout for Panel boards, MSB, SSB,
VDB, DB, Single line diagram, Transformer secondary panel boards and their Design, Fuse
grading conditions.

Switchgear Selection – MCB, MCCB, ACB, VCB, Oil CB, SF6 CB, SFU
Current Transformers and Potential Transformers – Types, Protection class, Burden, and
their selection

Cables and Conductors – Types of cables, HT and LT cables, Cable selection, Runs and
Cores of a cable, Voltage Drop calculations,
Busbars – Selection of Busbars, Busbar Trunking

Different types of meters used in Panel boards – Voltmeters, Ammeters, Powerfactor


meters, Frequency meter, Energy meters, Multifunction meters, Time of Day (TOD) meters,
Energy meter Panels.

Generator Control Panel – Design, Selection of Generators, Generator and Transformer


coupling – Change over switch, Bus coupler, Auto Main Failure Panel

 Electrical Design and Schematic Drawing preparation for a 3 Floor shopping complex.
 Electrical Design and Schematic Drawing preparation for a 5 Floor Residential flat
building.

Capacitors – Automatic Powerfactor Control (APFC) Panel, KVAR Rating calculations,

Earthing and its importance – Types of Earthings, Earthing Design, Selection of Earth
plates, HT and LT side earthing conductor design

Electrical Tests conducted before building construction - Earth Resistance measurement,


Earth Resistivity Measurements, Insulation Resistance Test

 Electrical Design and Schematic Drawing preparation for a 3-Floor Industrial Building

 Electrical Design and Schematic Drawing preparation for a 100-Flat Building (Civil
Drawings are given)

Transformer HT Panel design – Selection of DO Fuse, HT cable, HT CT, HT Protective


Device, PT
Relays – Types of Relays, ASCII coding, Relay connections

 Complete Electrical Design and Schematic Drawing preparation for an Industrial


building of Transformer capacity 500 KVA (Includes Generator Design, Transformer HT
and LT panel design, Earthing Design, APFC Panel Design)

 Complete Electrical Design and Schematic Drawing preparation for an Industrial


building of Transformer capacity 630 KVA (Includes Generator Design, Transformer HT
and LT panel design, Earthing Design, APFC Panel Design)

 Complete Electrical Design and Schematic Drawing preparation for an Industrial


building of Transformer capacity 750 KVA (Includes Generator Design, Transformer HT
and LT panel design, Earthing Design, APFC Panel Design)

You might also like