Tips for trouble-free usage

• Check correct orientation of tie holes when installing

TRIO 330 elements. (See Ties-below)
• Spray formwork on all sides with PERI BIO Clean
before every use.
• Spray back of formwork with water immediately
after concreting to reduce the cleaning work.
• Always start at a corner or difficult area.
Pay attention to the wall thickness. See corners.

TRIO 330
• Only use the required number of ties. Unused tie holes
must be sealed with plugs ø 20/24, item no. 030300.
60 72 • More information can be found in the TRIO assembly
instructions.

72

60
9.
Without exception, valid safety regulations must be observed

Extremely cost-effective 3.30 m high panel formwork in those countries where our products are used.

WDA 10
Ties
Permissible fresh concrete pressure for

60
Basic rule: Ties ➊ ➋ ➍ the TRIO 330. Elements certified
TRIO 330 panels have an asymmetrical for extended formwork according to guidelines issued by the
72 tie arrangement. When placing the Güteschutzverband Betonschalungen
elements, the tie hole ➌ must be in (Quality Protection Association for
the upper position. Wrong application Concrete Formwork), GSV.
results in more ties being used than is
necessary. 82.5 kN/m2 triangular load, DIN 18202,

Extension
Table 3, Line 7, with 2 ties.
For standard element joints. On external corners. For filler timbers up to 100 mm. For timber extensions.

Only one component is required for all connections.

The TRIO BFD alignment coupler ensures
that all panel joints are: flush
aligned
tight
6. T-junctions
Basic rules for T-junctions:
Wall thicknesses 180 – 400 mm
8. Wall Connections
1. With 330 x 240
Ties ➊ ➌
up to 3.30 m
concreting heights GSV geprüft

57.5
in only one step!

1.175 m
durch neutrales Prüfinstitut
External formwork: with panel TR 90 240 ➍
Internal formwork: with TRIO Corner TE Güteschutzverband Test report

1.075 m
Betonschalungen available on
Adapting to wall thicknesses using
240
➌ request.
TRIO wall thickness compensation

3.30 m

3.30 m
WDA 5, WDA 6 or timber infills.
Filler timber
➋

1.55 m

1.075 m
72
2. With WDA or timber

M
TR
WDA 5/6
➊ ➊

60
E
72

57.5

57.5
TG

E
4.

TG
TE
72
(180)
200

WDA 5 (6)
90

1. Standard Panel Connections TE 9. Shafts

TRM 72
3. With TRM 72

60
The TRIO shaft element
Filler timber allows complete shaft
TRM 72
TRM 72 formwork units to be moved
as one unit.
A 25 mm all-round
TRM 72
TRM 72 clearance for striking is
created when the formwork
panels are pulled.
Filler timber
1. With 330 x 240 2. With TRM 72 3. With TR 30 4. With WDA or timber infills 2. When striking,
lever crowbar
upwards.
TE
WDA 5/6 Shaft Element TSE 330,
(240)
250

WDA 5 (6)
Item no. 105525
90

Shaft Element TSE 270,

TRM 72

TRM 72

30

30

TE Item no. 105523

TAR 85

TAR 85

Shaft Element TSE 120,

Item no. 105524
4 pieces per shaft.
For rectangular
shafts, shorten
240

240

the chains on the

longitudinal sides
to ensure that all
TRIO shaft
elements are
evenly loaded.

2. Length Adjustment TE 4. Oblique Angles

WDA 5 (6)
(360)
350

Quick and easy solution up to 100 mm. Economical solution. Optimal visible surface solution. TRIO articulated corner TGE for angles Internal formwork: External formwork:
90

With timber, or timber and formlining With filler plates from 60 – 360 mm. With formlining and filler support of 75° and more – for internal and with TR 60 or TR 30 panels and articulated with multi-panel TRM 72 and
plus BFD alignment coupler. Filler Plate LA 330, Item No. 054384. TPP, Alu 330, Item No. 101829. TE external corners alike. corners articulated corners

TAR 85 Internal element connection: External element connection:

TRM 72 TGE
5 BFD couplers 2 compensation walers TAR 85,
8 BFD couplers
6. 30 TGE

85
TAR 2
5.
75°

7
Filler timber
TRM 72

TRM
30
TE 60
30
90

TE TE
30
TE TE
TE Filler timber
72

TAR 85
400

WDA 5
TRM 72
90

TRM 72 TGE
60 60

7. 3.

TATRM
TE
60 TGE

R 7
85 2
135°
TRM 72

TRM 72

60

Filler plate LA Formlining Filler support TPP

BFD alignment coupler TAR 85 TAR 85

max. 100 mm 60 – 360 mm max. 360 mm

Extension Units Tie hole positions
Formwork should be assembled Compensation Waler TAR 85
to its full height on the ground! BFD Alignment Coupler

7. Stopend Formwork 5. Wall Offsets 3. Corners TE TGE TGE TE

Extensions with
330 240 120 90 72 60 30
W igh

120 x 240 panels

id t
H

Internal Internal External External

e
th

Using the TRIO MT/MTF stopend panel with continuous Up to max. 200 mm Basic rules for corners Internal formwork: External formwork:
240 - 330

reinforcement, with or without water bars. Lower TAR 85 to be

fixed from below Wall thicknesses 180 – 400 mm. with TRIO Corner TE with TR 72 panels, or TRM 72 and TR 60
30
200 250
MTF centre part with water bar. MT centre part without water bar. Filler timber
Adapting to wall thicknesses using Connection: Connection:
200 mm

TRIO wall thickness compensation (180) (240) 3 BFD alignment couplers for h = 3.30 m 7 BFD alignment couplers for h = 3.30 m
max.

WDA 5, WDA 6 or timber infills.

Stopend panel 270

TAR 85

30
Timber
2 WDA 5 (6) WDA 5 (6)
Additional BFD for Hook tie
120 mm offsets upwards DW 15/400
360
240

240
TRM 72
TRM 72

TAR 85 TE
72

TE
72

Up to max. 860 mm
60
60
TRM 72
TAR 85

860 mm
max.
Stopend panel 120

Stopend tie TAR 85

60 350 400 x
200 mm

(360)
390
min.

AT MTF AT AT MT AT
c c c c TE
TE
The concrete cover c is 25 mm or 50 mm. Timber infills
60
TAR 85 Stopend tie
TE
Push-Pull Props and Kicker Braces
TAR 85

TE
TE
TRM 72
TAR 85

Filler timber WDA 5 (6) 2 WDA 5

72

72

72

Push-pull props and kicker braces for Other push-pull props, according to the For assembly of
base plates.
Ankerschraube
60 60 60
aligning the formwork as well as table, are attached to the panels by Multi-Monti MMS 20x130
420

Art. Nr.: 103606

TAR 85
transferring wind loads means of TRIO brace connectors and to
Zur Befestigung von
Richtstützen, Abspannungen bei
SKYDECK Bühnen oder

PERI anchor bolt

auskragenden Deckentischen
ist die Multi-Monti Schraube
eine ideale Alternative zu bisher

are to be arranged as shown in the the slab using appropriate base plates
eingesetzten
Befestigungssystemen.

MMS 20 x 130
Die Vorteile im Überblick
– mehrfach wiederverwendbar
– einfache Durchsteckmontage
– enorme Zeit- und Kostenersparnis

drawings and table below. The first and PERI anchor bolts MMS 20 x 130.
Transport and Storage
– keine Sprengwirkung des Dübels

Item no. 103606

Extensions
– geprüfte Sicherheit auch in

niederfestem, nicht ausge-

härtetem Beton.

element must always have 2 push-pull

props attached.
Technische Daten

Ankerlänge L [mm] 130 Bruchlastmitte

in 2 Tage altem ungerissenem Beton

Alignment couplers and all-round struts Extension up to max. 8.10 m high can
Klemmstärke tfix [mm] 10-15 bei erreichter Festigkeit
Fmax [kN] 41,7

Stacking Device TRIO, galv. Lifting Gear Combi-2 TRIO

βw ≥ 10 N/mm2

Lifting Hook TRIO

Verankerungstiefe hnom≥ [mm] 115
empfohlene Last in B10
Bohrtiefe hO ≥ [mm] 140 ungerissenem Beton oder ungeris- empf. FQ [kN] 10,4
sener Beton bei erreichter Festigkeit
Bohrer ø (Hammerbohrer DIN 8035) dO [mm] 18 βw ≥ 10 N/mm2 empf. FZ [kN] 10,4
Sicherheitsbeiwert s = 4
Max. Anzugsdrehmoment MDmax [Nm] 150

ensure that extensions using TRIO are be assembled as one unit.

empfohlene Last in B25

Perm. load of 500 kg/piece Perm. load of 2.9 t with 45° lifting gear angle.
empf. FQ [kN]

Maximum load capacity of 1.5 t,

Schlüsselweite SW [mm] 30 ungerissener Beton 16,4
Sicherheitsbeiwert s = 4 empf. FZ [kN] 16,4
Abstand a ≥ [mm] 360
Randabstand ar ≥ [mm] 180
Mindestbauteildicke d ≥ [mm] 240

Table for PERI push-pull props and kicker braces For safe stacking of 5 TRIO panels The pins are used to move stacks of panels located on the ground. easier.
Durchgangsloch im zu

max. lifting gear angle of 30°.

befestigenden Teil db [mm] 21

a PERI GmbH
ar r
a a

of any size.
Postfach 12 64

Always use in pairs! TRIO lifting hooks or TRIO stacking devices are attached to the
SW 30
a a
tfix 89259 Weißenhorn
Tel.: 0 73 09 / 9 50 - 0
hnom Fax: 0 73 09 / 9 50 - 176
www.peri.de
450

Fig. 1 Fig. 2 load hook. Example: h = 6.60 m Example: h = 7.80 m

Formwork height h [m]
3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 Follow Instructions for Use!
Follow Instructions for Use! Follow Instructions for Use! Lifting Gear Combi-2 TRIO
Fig. 2 Item no. 044760
Max. width of influence [m] 3.53 2.73 2.19 1.82 1.58 1.42 1.93 1.67 1.49 1.35

Actual prop load FRS [kN] F1 9.4 11.3 11.3 11.3

y1
y2
0.8 kN/m2

at maximum prop spacing 9.7 9.7 9.8 9.8 9.8 9.6

F2 9.5 8.5 9.3 10.1 Stacking Device TRIO Lifting Hook TRIO
Item no. 023390 Item no. 023690
Actual kicker load FAV [kN]
at maximum prop spacing 2.1 2.3 2.2 2.2 2.3 2.6 2.6 2.3 2.1 1.9 PERI Paletten und
Stapelrungen
TRIO Versetzhaken 1,5t
Art.-Nr. 023690
TRIO Kombigehänge-2
Art.-Nr. 044760

Bedienungsanleitung Bedienungsanleitung Bedienungsanleitung

x1 4.3 4.7 5.3 5.9

x = dist. of base plate from 1.2 1.6 2.0 2.4 2.9 3.5
rear edge of formwork x2 2.6 2.6 2.8 3.0
480

y1 1.5 1.8 1.8 1.8 Fig. 1

y = *top connection point
h

from top of formwork 1.0 1.2 1.5 1.8 2.0 2.0 y2 4.5 5.5 6.2 6.9
y

* If necessary, the distance from the top of the formwork must be Ausgabe 05/2007
F RS 1

Ausgabe 05/2007 Ausgabe 05/2007

0.5 kN/m2

0.5 kN/m2

adapted to the system.

F RS 2

Instructions for Use

h

For the given widths of influence, a maximum force of 11.3 kN is Instructions for Use Instructions for Use
Pallets and Stacking Devices Lifting Hook TRIO Lifting Gear Combi-2 TRIO
F RS

transferred into the building at the foot of the push-pull prop.

FAV FAV
Wind loads: h < 8 m = 0.5 kN/m2 60° 60° 60°
8 m < h < 20 m = 0.8 kN/m2
x x2

x1
510

TRIO Panels
Width
240 120 90 60 30 72 TE TRM 72 TGE
Height
Internal corner Multi-purpose Articulated
with 30 cm leg panel with corner from 75°
length continuous tie to 285° for
hole strip internal and Max. 5 TRIO panels 330 x 240 can
external corners be transported with the lifting gear
540

combi-2.
Secure stack of panels by means of
tie rods to prevent panels moving
during lifting.
TR 330

Compensation Waler TAR 85

Working Platforms Item no. 023550 For heights of 5.40 m, we recommend using 2 x 2.70 m

Scaffold Bracket
TRG 80 Item no. 023670
Handrail Post Holder TRIO
TRG 120 Item no. 023680 Item no. 101592
Two TAR 85 compensation walers and
two BFD alignment couplers are required
m2 7.92 3.96 2.97 1.98 0.99 2.38 1.98 2.38 1.98
570

Item no. 054304 054314 054324 054354 054364 054334 054374 054344 054414 for extension heights up to 8.10 m per
Weight 398.00 kg 192.00 kg 135.00 kg 97.40 kg 64.90 kg 107.00 kg 86.10 kg 122.00 kg 121.00 kg Planking and Guardrails or element joint.
m
for working platforms are to be fitted . 10 m 1.35
2 c e
according to current valid guidelines. x. n
Ma influe
Maximum spacing of the scaffold Handrail Post HSGP f
ho
brackets = 1.35 m with a permissible Item no. 034580
w idt
load of 150 kg/m2.
TR 270

Concrete scaffolding with guardrails

End Handrail Frame 55
Item no. 065066
600

m2 6.48 3.24 2.43 1.62 0.81 1.94 1.62 1.94 1.62 Concreting Platform 120 x 270
Item no. 022570 022510 022520 022550 022560 022530 022580 022540 023200 Item no. 022950
Weight 329.00 kg 159.00 kg 112.00 kg 80.30 kg 52.90 kg 89.20 kg 68.80 kg 93.80 kg 94.80 kg

A single platform unit is only 32 cm high

when folded. Each additional unit adds Using 2.70 m panels reduces the number of ties at the bottom.
TR 120

only 17 cm in height. 13 concreting

platforms (35 m) stacked on top of each
other is equal to the loading height of
> 3.00 m

a truck.
m2 2.88 1.44 1.08 0.72 0.36 0.86 0.72 0.86 0.72
Item no. 022514 022600 022610 022640 022650 022620 022660 022630 032300
Weight 163.00 kg 67.90 kg 52.80 kg 39.50 kg 24.90 kg 43.50 kg 32.80 kg 51.90 kg 43.60 kg
660
TR 60

170
320

m2 0.72 0.54 0.36 0.18 0,43 0.36

Item no. 022640 022790 022810 022820 022800 022840
Weight 39.50 kg 31.40 kg 24.20 kg 14.60 kg 26.30 kg 18.00 kg
1466

Edition 12/2007
 TRIO 330
Panel Formwork

Poster

Edition 09/2009

TRIO_330_P_Titel.indd 1 04.09.2009 8:05:33 Uhr

 PERI Product Range

Wall Formwork Climbing Systems

Panel Formwork Climbing Scaffold
Girder Formwork Self-Climbing System
Circular Formwork Climbing Protection Panel
Facade Formwork Platform Systems
Brace Frame

Column Formwork Scaffold, Stairways,

Square Working Platforms
Rectangular Facade Scaffold
Circular Working Platform
Weather Protection Roof
Stairway Access

Slab Formwork Bridge and Tunnel

Panel Formwork Formwork
Beam Grid Formwork Cantilevered Parapet Carriage
Girder Formwork Cantilevered Parapet Platform
Slab Table Engineer’s Construction Kit
Beam Formwork

Shoring Systems Services

Steel Slab Props Formwork Assembly

D e 09/2009 5ma Art.-Nr.: 791853 © Copyright by PERI GmbH

Aluminium Slab Props Cleaning / Repairs
Tower Systems Formwork Planning
Heavy-Duty Props Software
Statics
Special Constructions

Additional Systems
Plywood
Formwork Girders
Stopend Systems
Pallets
Transportation Containers

PERI GmbH
Formwork Scaffolding Engineering
P.O. Box 1264
89259 Weissenhorn
Germany
Tel +49 (0)73 09.9 50- 0
Fax +49 (0)73 09.9 51- 0
[email protected]
www.peri.com

(1B5XŴFNVHLWHLQGG 8KU