CONCRET DESIGN (SUBSTRUCTURE)

1. STAAD SPACE
INPUT FILE: E:\MURSprojFiles\a.)SKSU Project\1. SKSU infra porjects\Isulan\2023_Engineering Laboratory.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 04-MAY-23
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1001 0 0 0; 1002 0 0 5; 1003 0 0 10; 1004 0 0 12; 1005 4 0 0; 1006 4 0 5
9. 1007 4 0 10; 1008 4 0 12; 1009 8 0 0; 1010 8 0 5; 1011 8 0 10; 1012 8 0 12
10. 1013 0 -1.5 0; 1014 0 -1.5 5; 1015 0 -1.5 10; 1016 0 -1.5 12; 1017 4 -1.5 0
11. 1018 4 -1.5 5; 1019 4 -1.5 10; 1020 4 -1.5 12; 1021 8 -1.5 0; 1022 8 -1.5 5
12. 1023 8 -1.5 10; 1024 8 -1.5 12
13. MEMBER INCIDENCES
14. 1 1001 1002; 2 1002 1003; 3 1003 1004; 4 1004 1008; 5 1008 1012; 6 1012 1011
15. 7 1011 1010; 8 1010 1009; 9 1009 1005; 10 1005 1001; 11 1005 1006
16. 12 1006 1007; 13 1007 1008; 14 1003 1007; 15 1007 1011; 16 1002 1006
17. 17 1006 1010; 18 1001 1013; 19 1002 1014; 20 1003 1015; 21 1004 1016
18. 22 1005 1017; 23 1006 1018; 24 1007 1019; 25 1008 1020; 26 1009 1021
19. 27 1010 1022; 28 1011 1023; 29 1012 1024
20. START GROUP DEFINITION
21. FLOOR
22. _G2W 1 TO 17
23. END GROUP DEFINITION
24. SUPPORTS
25. 1013 TO 1024 FIXED
26. DEFINE MATERIAL START
27. ISOTROPIC CONCRETE_21MPA
28. E 2.1538E+07
29. POISSON 0.17
30. DENSITY 23.5616
31. ALPHA 1E-05
32. DAMP 0.05
33. G 9.28141E+06
34. TYPE CONCRETE
35. STRENGTH FCU 21000
36. END DEFINE MATERIAL
37. MEMBER PROPERTY AMERICAN
38. 18 TO 29 PRIS YD 0.4 ZD 0.4
39. 1 TO 17 PRIS YD 0.5 ZD 0.3
40. CONSTANTS
41. MATERIAL CONCRETE_21MPA ALL
42. MEMBER CRACKED
43. 18 TO 29 REDUCTION RIY 0.700000 RIZ 0.700000
44. 1 TO 17 REDUCTION RIY 0.350000 RIZ 0.350000
45. LOAD 1 LOADTYPE SEISMIC TITLE EZ
46. JOINT LOAD
47. 1001 FX -2.668 FY 27.471 FZ 34.261 MX 97.158 MY 1.146 MZ 7.384
48. 1002 FX -0.691 FY -7.233 FZ 39.425 MX 105.366 MY 1.146 MZ 1.946
49. 1003 FX 1.245 FY 103.313 FZ 42.753 MX 110.655 MY 1.146 MZ -3.427
50. 1004 FX 2.142 FY -123.484 FZ 39.048 MX 104.767 MY 1.146 MZ -5.771
51. 1005 FX -3.098 FY 29.314 FZ 32.701 MX 92.844 MY 1.146 MZ 8.067
52. 1006 FX -0.821 FY -6.115 FZ 37.682 MX 100.759 MY 1.146 MZ 2.152
53. 1007 FX 1.439 FY 98.227 FZ 40.891 MX 105.86 MY 1.146 MZ -3.734
54. 1008 FX 2.424 FY -121.429 FZ 37.26 MX 100.089 MY 1.146 MZ -6.218
55. 1009 FX -2.668 FY 31.157 FZ 31.142 MX 88.53 MY 1.146 MZ 7.384
56. 1010 FX -0.691 FY -4.996 FZ 35.939 MX 96.153 MY 1.146 MZ 1.946
57. 1011 FX 1.245 FY 93.143 FZ 39.03 MX 101.066 MY 1.146 MZ -3.427
58. 1012 FX 2.142 FY -119.369 FZ 35.472 MX 95.411 MY 1.146 MZ -5.77
59. LOAD 2 LOADTYPE SEISMIC TITLE EX
60. JOINT LOAD
61. 1001 FX 35.227 FY 45.418 FZ -0.388 MX -1.163 MY -0.341 MZ -99.364
62. 1002 FX 34.745 FY 45.088 FZ -0.456 MX -1.271 MY -0.341 MZ -97.917
63. 1003 FX 34.476 FY 39.267 FZ -0.555 MX -1.428 MY -0.341 MZ -96.806
64. 1004 FX 35.548 FY 57.425 FZ 0.116 MX -0.362 MY -0.341 MZ -98.237
65. 1005 FX 42.003 FY 0 FZ 0 MX 0 MY -0.341 MZ -110.135
66. 1006 FX 41.393 FY 0 FZ 0 MX 0 MY -0.341 MZ -108.483
67. 1007 FX 40.854 FY -0.004 FZ 0 MX 0 MY -0.341 MZ -106.943
68. 1008 FX 41.368 FY -0.083 FZ 0 MX 0 MY -0.341 MZ -107.487
69. 1009 FX 35.227 FY -45.418 FZ 0.388 MX 1.163 MY -0.341 MZ -99.364
70. 1010 FX 34.745 FY -45.089 FZ 0.456 MX 1.271 MY -0.341 MZ -97.917
71. 1011 FX 34.475 FY -39.263 FZ 0.555 MX 1.429 MY -0.341 MZ -96.805
72. 1012 FX 35.542 FY -57.342 FZ -0.116 MX 0.362 MY -0.341 MZ -98.228
73. LOAD 3 LOADTYPE DEAD TITLE DL
74. SELFWEIGHT Y -1
75. FLOOR LOAD
76. _G2W FLOAD -4.25 GY
**NOTE** about Floor/OneWay Loads/Weights.
Please note that depending on the shape of the floor you may
have to break up the FLOOR/ONEWAY LOAD into multiple commands.
For details please refer to Technical Reference Manual
Section 5.32.4.2 Note d and/or "5.32.4.3 Note f.
**NOTE** about FLOOR GROUP command
All floor panels in a floor group should lie in a single plane.
If not lying in a single plane break single FLOOR GROUP
command into multiple FLOOR GROUP commands where each
floor group lie in a single plane / height.
77. JOINT LOAD
78. 1001 FX -2.051 FY -187.123 FZ -5.806 MX -8.409 MY -0.587 MZ 1.644
79. 1002 FX -1.544 FY -263.371 FZ 0.673 MX 1.888 MY -0.587 MZ 2.014
80. 1003 FX -2.205 FY -162.863 FZ 4.316 MX 7.678 MY -0.587 MZ 4.241
81. 1004 FX -3.059 FY -121.859 FZ -2.076 MX -2.482 MY -0.587 MZ 6.069
82. 1005 FX 1.477 FY -247.755 FZ -4.982 MX -6.159 MY -0.587 MZ -3.964
83. 1006 FX 0.392 FY -243.436 FZ 2.909 MX 6.383 MY -0.587 MZ -1.063
84. 1007 FX -0.681 FY -142.811 FZ 3.818 MX 7.827 MY -0.587 MZ 1.819
85. 1008 FX -1.167 FY -191.006 FZ -2.465 MX -2.158 MY -0.587 MZ 3.06
86. 1009 FX 4.474 FY -189.782 FZ -4.394 MX -4.283 MY -0.587 MZ -8.728
87. 1010 FX 2.167 FY -264.965 FZ 2.313 MX 6.376 MY -0.587 MZ -3.885
88. 1011 FX 1.081 FY -155.414 FZ 6.104 MX 12.402 MY -0.587 MZ -0.982
89. 1012 FX 1.086 FY -125.148 FZ -0.41 MX 2.049 MY -0.587 MZ -0.52
90. MEMBER LOAD
91. 1 TO 17 UNI GY -1.87
92. LOAD 4 LOADTYPE LIVE TITLE LL
93. FLOOR LOAD
94. _G2W FLOAD -1.9 GY
95. JOINT LOAD
96. 1001 FX -0.344 FY -8.478 FZ -0.482 MX -0.463 MY 0 MZ 0.547
97. 1002 FX -0.611 FY -19.311 FZ 0.266 MX 0.726 MY 0 MZ 0.971
98. 1003 FX -0.566 FY -10.839 FZ 0.759 MX 1.51 MY 0 MZ 0.899
99. 1004 FX -0.646 FY -14.466 FZ -0.388 MX -0.313 MY 0 MZ 1.027
100. 1005 FX 0 FY -18.554 FZ -0.935 MX -1.182 MY 0 MZ -0.001
101. 1006 FX 0 FY -40.232 FZ 0.273 MX 0.738 MY 0 MZ -0.001
102. 1007 FX 0 FY -25.185 FZ 1.102 MX 2.056 MY 0 MZ 0
103. 1008 FX -0.001 FY -26.24 FZ -0.743 MX -0.877 MY 0 MZ 0.002
104. 1009 FX 0.345 FY -8.479 FZ -0.482 MX -0.462 MY 0 MZ -0.549
105. 1010 FX 0.612 FY -19.312 FZ 0.266 MX 0.727 MY 0 MZ -0.972
106. 1011 FX 0.566 FY -10.817 FZ 0.76 MX 1.512 MY 0 MZ -0.899
107. 1012 FX 0.645 FY -14.516 FZ -0.394 MX -0.323 MY 0 MZ -1.026
108. LOAD COMB 13 GENERATED NSCP 2015 CONCRETE DESIGN 1
109. 3 1.4
110. LOAD COMB 14 GENERATED NSCP 2015 CONCRETE DESIGN 2
111. 3 1.42 4 0.5 1 1.25
112. LOAD COMB 15 GENERATED NSCP 2015 CONCRETE DESIGN 3
113. 3 1.42 4 0.5 2 1.25
114. LOAD COMB 16 GENERATED NSCP 2015 CONCRETE DESIGN 4
115. 3 1.42 4 0.5 1 -1.25
116. LOAD COMB 17 GENERATED NSCP 2015 CONCRETE DESIGN 5
117. 3 1.42 4 0.5 2 -1.25
118. LOAD COMB 18 GENERATED NSCP 2015 CONCRETE DESIGN 6
119. 3 1.2 4 1.6
120. LOAD COMB 19 GENERATED NSCP 2015 CONCRETE DESIGN 7
121. 3 1.42 1 1.25
122. LOAD COMB 20 GENERATED NSCP 2015 CONCRETE DESIGN 8
123. 3 1.42 2 1.25
124. LOAD COMB 21 GENERATED NSCP 2015 CONCRETE DESIGN 9
125. 3 1.42 1 -1.25
126. LOAD COMB 22 GENERATED NSCP 2015 CONCRETE DESIGN 10
127. 3 1.42 2 -1.25
128. LOAD COMB 23 GENERATED NSCP 2015 CONCRETE DESIGN 11
129. 3 0.68 1 1.25
130. LOAD COMB 24 GENERATED NSCP 2015 CONCRETE DESIGN 12
131. 3 0.68 2 1.25
132. LOAD COMB 25 GENERATED NSCP 2015 CONCRETE DESIGN 13
133. 3 0.68 1 -1.25
134. LOAD COMB 26 GENERATED NSCP 2015 CONCRETE DESIGN 14
135. 3 0.68 2 -1.25
136. LOAD COMB 27 GENERATED NSCP 2015 NSCP 203.4.2 1
137. 3 1.0 4 1.0
138. LOAD COMB 28 GENERATED NSCP 2015 NSCP 203.4.2 2
139. 3 1.0 4 0.75 1 0.535
140. LOAD COMB 29 GENERATED NSCP 2015 NSCP 203.4.2 3
141. 3 1.0 4 0.75 2 0.535
142. LOAD COMB 30 GENERATED NSCP 2015 NSCP 203.4.2 4
143. 3 1.0 4 0.75 1 -0.535
144. LOAD COMB 31 GENERATED NSCP 2015 NSCP 203.4.2 5
145. 3 1.0 4 0.75 2 -0.535
146. LOAD COMB 32 GENERATED NSCP 2015 NSCP 203.4.2 6
147. 3 1.0 1 0.7
148. LOAD COMB 33 GENERATED NSCP 2015 NSCP 203.4.2 7
149. 3 1.0 2 0.7
150. LOAD COMB 34 GENERATED NSCP 2015 NSCP 203.4.2 8
151. 3 1.0 1 -0.7
152. LOAD COMB 35 GENERATED NSCP 2015 NSCP 203.4.2 9
153. 3 1.0 2 -0.7
154. LOAD COMB 36 GENERATED NSCP 2015 NSCP 203.4.2 10
155. 3 1.0 4 1.0 1 0.71
156. LOAD COMB 37 GENERATED NSCP 2015 NSCP 203.4.2 11
157. 3 1.0 4 1.0 2 0.71
158. LOAD COMB 38 GENERATED NSCP 2015 NSCP 203.4.2 12
159. 3 1.0 4 1.0 1 -0.71
160. LOAD COMB 39 GENERATED NSCP 2015 NSCP 203.4.2 13
161. 3 1.0 4 1.0 2 -0.71
162. PERFORM ANALYSIS
PROBLEMSTATISTICS
-----------------------------------
NUMBER OF JOINTS 24 NUMBER OF MEMBERS 29
NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 12
Using 64-bit analysis engine.
SOLVER USED IS THE OUT-OF-CORE BASIC SOLVER
ORIGINAL/FINAL BAND-WIDTH= 12/ 7/ 24 DOF
TOTAL PRIMARY LOAD CASES = 4, TOTAL DEGREES OF FREEDOM = 72
TOTAL LOAD COMBINATION CASES = 27 SO FAR.
SIZE OF STIFFNESS MATRIX = 2 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.1/ 89563.3 MB
163. LOAD LIST ALL
164. START CONCRETE DESIGN
CONCRETE DESIGN
165. CODE ACI 2011
166. CLB 0.04 ALL
167. CLS 0.04 ALL
168. CLT 0.04 ALL
169. FC 21000 ALL
170. FYMAIN 275000 ALL
171. FYSEC 275000 ALL
172. MAXMAIN 20 ALL
173. MINMAIN 20 ALL
174. TRACK 2 MEMB 18 TO 29
175. DESIGN BEAM 3
ACI 318-11 BEAM NO. 3 DESIGN RESULTS
=============================================
LEN - 2000. MM FY - 275. FC - 21. MPA, SIZE - 300. X 500. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 63. 4 - 20MM 0. 2000. YES YES
2 437. 4 - 20MM 0. 2000. YES YES
B E A M N O. 3 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 130.56 KNS Vc= 113.55 KNS Vs= 60.53 KNS
Tu= 2.53 KN-MET Tc= 4.1 KN-MET Ts= 0.0 KN-MET LOAD 16
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 219. MM C/C FOR 565. MM
AT END SUPPORT - Vu= 119.56 KNS Vc= 111.08 KNS Vs= 48.33 KNS
Tu= 0.84 KN-MET Tc= 4.1 KN-MET Ts= 0.0 KN-MET LOAD 19
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT IS REQUIRED FOR SHEAR.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 219. MM C/C FOR 565. MM

********************END OF BEAM DESIGN**************************

176. DESIGN COLUMN 22
ACI 318-11 COLUMN NO. 22 DESIGN RESULTS
===============================================
FY - 275.0 FC - 21.0 MPA, SQRE SIZE - 400.0 X 400.0 MMS, TIED
AREA OF STEEL REQUIRED = 2742.4 SQ. MM
BAR CONFIGURATION REINF PCT. LOAD LOCATION PHI
----------------------------------------------------------
12 - 20 MM 2.356 24 END 0.650
(PROVIDE EQUAL NUMBER OF BARS ON EACH FACE)
TIE BAR NUMBER 12 SPACING 320.00 MM
COLUMN INTERACTION: MOMENT ABOUT Z -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3825.44 3060.35 1548.37 250.34 161.7
M0 P-tens. Des.Pn Des.Mn e/h
163.71 -1036.73 345.30 164.74 0.31806
--------------------------------------------------------
COLUMN INTERACTION: MOMENT ABOUT Y -AXIS (KN-MET)
--------------------------------------------------------
P0 Pn max P-bal. M-bal. e-bal. (MM)
3825.44 3060.35 1548.37 250.34 161.7
M0 P-tens. Des.Pn Des.Mn e/h
163.71 -1036.73 345.30 7.19 0.01388
--------------------------------------------------------
Pn Mn Pn Mn (@ Z )
| 2824.94 148.27 1412.47 250.64
P0 |* 2589.53 172.47 1177.06 248.71
| * 2354.12 194.41 941.65 244.41
Pn,max|__* 2118.70 213.83 706.23 232.57
| * 1883.29 230.43 470.82 215.26
Pn | * 1647.88 244.69 235.41 195.49
NOMINAL| * Pn Mn Pn Mn (@ Y )
AXIAL| * 2824.94 148.27 1412.47 250.64
COMPRESSION| * 2589.53 172.47 1177.06 248.71
Pb|-------*Mb 2354.12 194.41 941.65 244.41
| * 2118.70 213.83 706.23 232.57
___________|____*_______ 1883.29 230.43 470.82 215.26
| * M0 Mn, 1647.88 244.69 235.41 195.49
| * BENDING
P-tens|* MOMENT
|
********************END OF COLUMN DESIGN RESULTS********************
************** CONCRETE TAKE OFF **************
(FOR BEAMS, COLUMNS AND PLATES DESIGNED ABOVE)
NOTE: CONCRETE QUANTITY REPRESENTS VOLUME OF CONCRETE IN BEAMS, COLUMNS, AND PLATES DESIGNED ABOVE.
REINFORCING STEEL QUANTITY REPRESENTS REINFORCING STEEL IN BEAMS AND COLUMNS DESIGNED ABOVE.
REINFORCING STEEL IN PLATES IS NOT INCLUDED IN THE REPORTED QUANTITY.
TOTAL VOLUME OF CONCRETE = 0.5 CU.METER
BAR SIZE WEIGHT
NUMBER (in lbs)
-------- --------
12 25
20 184
------------
*** TOTAL= 209
179. FINISH

CONCRET DESIGN (SUBSTRUCTURE)

INPUT FILE: E:\MURSprojFiles\a.)SKSU Project\1. SKSU infra porjects\Isulan\2023_Engineering Laboratory.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 29-MAR-23
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 15 0 4.8 0; 16 4 4.8 0; 17 8 4.8 0; 18 0 4.8 5; 19 4 4.8 5; 20 8 4.8 5
9. 21 0 4.8 10; 22 4 4.8 10; 23 8 4.8 10; 24 0 4.8 12; 25 4 4.8 12; 26 8 4.8 12
10. 27 0 4.8 12.65; 28 8 4.8 12.65; 29 0 8 0; 30 4 8 0; 31 8 8 0; 32 0 8 5
11. 33 4 8 5; 34 8 8 5; 35 0 8 10; 36 4 8 10; 37 8 8 10; 38 0 8 12; 39 4 8 12
12. 40 8 8 12; 41 4 4.8 14; 42 0 8 12.65; 43 8 8 12.65; 44 4 8 14; 1001 0 0 0
13. 1002 0 0 5; 1003 0 0 10; 1004 0 0 12; 1005 4 0 0; 1006 4 0 5; 1007 4 0 10
14. 1008 4 0 12; 1009 8 0 0; 1010 8 0 5; 1011 8 0 10; 1012 8 0 12
15. MEMBER INCIDENCES
16. 21 1001 15; 22 1005 16; 23 1009 17; 24 1002 18; 25 1006 19; 26 1010 20
17. 27 1003 21; 28 1007 22; 29 1011 23; 30 1004 24; 31 1008 25; 32 1012 26
18. 35 15 16; 36 16 17; 37 15 18; 38 16 19; 39 17 20; 40 18 19; 41 19 20; 42 18 21
19. 43 19 22; 44 20 23; 45 21 22; 46 22 23; 47 21 24; 48 22 25; 49 23 26; 50 24 25
20. 51 25 26; 52 24 27; 53 26 28; 55 15 29; 56 16 30; 57 17 31; 58 18 32; 59 19 33
21. 60 20 34; 61 21 35; 62 22 36; 63 23 37; 64 24 38; 65 25 39; 66 26 40; 69 29 30
22. 70 30 31; 71 29 32; 72 30 33; 73 31 34; 74 32 33; 75 33 34; 76 32 35; 77 33 36
23. 78 34 37; 79 35 36; 80 36 37; 81 35 38; 82 36 39; 83 37 40; 84 38 39; 85 39 40
24. 86 25 41; 87 27 41; 88 28 41; 89 38 42; 90 40 43; 91 39 44; 92 42 44; 93 43 44
25. START GROUP DEFINITION
26. FLOOR
27. _2W2F 35 TO 51
28. END GROUP DEFINITION
29. MEMBER CURVE
30. 87 92 RADIUS 6.60093 GAMMA 90 PRESSURE 0
31. 88 93 RADIUS 6.00926 GAMMA 270 PRESSURE 0
32. DEFINE MATERIAL START
33. ISOTROPIC CONCRETE_21MPA
34. E 2.1538E+07
35. POISSON 0.17
36. DENSITY 23.5616
37. ALPHA 1E-05
38. DAMP 0.05
39. G 9.28141E+06
40. TYPE CONCRETE
41. STRENGTH FCU 21000
42. END DEFINE MATERIAL
43. MEMBER PROPERTY AMERICAN
44. 21 TO 32 55 TO 66 PRIS YD 0.4 ZD 0.4
45. 69 TO 85 89 TO 93 PRIS YD 0.35 ZD 0.3
46. 35 TO 37 39 TO 42 44 TO 47 49 TO 53 PRIS YD 0.5 ZD 0.35
47. 38 43 48 86 PRIS YD 0.5 ZD 0.35
48. MEMBER PROPERTY AMERICAN
49. 87 88 PRIS YD 0.45 ZD 0.35
50. CONSTANTS
51. MATERIAL CONCRETE_21MPA ALL
52. SUPPORTS
53. 1001 TO 1012 FIXED
54. MEMBER CRACKED
55. 21 TO 32 55 TO 66 REDUCTION RIY 0.700000 RIZ 0.700000
56. 35 TO 53 69 TO 88 REDUCTION RIY 0.350000 RIZ 0.350000
57. DEFINE REFERENCE LOADS
58. LOAD R1 LOADTYPE DEAD TITLE DL
59. SELFWEIGHT Y -1
60. MEMBER LOAD
61. 35 TO 37 39 42 44 UNI GY -8.7
62. 35 TO 39 42 44 UNI GY -6.72
63. 35 TO 39 42 44 69 TO 71 73 76 78 81 83 89 90 92 93 UNI GY -2.98
64. FLOOR LOAD
65. _2W2F FLOAD -4.25 GY
66. JOINT LOAD
67. 38 TO 40 FX -0.58 FY -3.4 FZ 0
68. 35 TO 37 FX 3.1 FY -20.83
69. 29 TO 31 FX 7.86 FY -21.42 FZ 0
70. 32 TO 34 FX -10.39 FY -33.44 FZ 0
71. MEMBER LOAD
72. 50 TO 53 87 88 UNI GY -4.25
73. END DEFINE REFERENCE LOADS
*** NOTE: NEITHER "MASS" NOR "GRAVITY" REFERENCE LOADTYPE IS PRESENT.
MASS MODEL IS FORMED BY COMBINING ALL "DEAD" AND "LIVE" (IF ANY) REFERENCE LOADTYPES.
*** NOTE: MASS MODEL FORMED WILL BE USED IN SEISMIC/RESPONSE/TIME HISTORY LOADING, IF ANY.
IF MASS MODEL IS SEPARATELY PROVIDED IN INDIVIDUAL LOADING, THE GENERATED MASS
WILL BE REPLACED BY THE MASS PROVIDED IN INDIVIDUAL LOADING.
74. FLOOR DIAPHRAGM
75. DIA 1 TYPE RIG HEI 4.8 JOINT 15 TO 28 41
76. DIA 3 TYPE RIG HEI 8 JOINT 29 TO 40 42 TO 44
77. CHECK SOFT STORY ASCE7
FLOOR DIAPHRAGM
************************************************************************************
FLOOR DIAPHRAGM UNIT - KN METE
--------------- ----------------
NO. TYPE FL. LEVEL FL. WT CENTRE OF MASS MASTER JOINT NO.
XZ
1 RIGID 4.800 1554.72 4.000 5.773 1013
3 RIGID 8.000 632.24 4.000 6.347 1014
************************************************************************************
78. DEFINE UBC LOAD
79. ZONE 0.4 I 1.5 RWX 8.5 RWZ 8.5 STYP 4 NA 1 NV 1
80. REFERENCE LOAD Y
*** NOTE: SEISMIC WEIGHT TABLE IS PRESENT.THIS WEIGHT TABLE
WILL BE CONSIDERED IN STATIC SEISMIC ANALYSIS.
81. R1 1.0
82. LOAD 1 LOADTYPE SEISMIC TITLE EX
83. UBC LOAD X 1 DEC 1 ACC 0.05
84. PERFORM ANALYSIS
PROBLEMSTATISTICS
-----------------------------------
NUMBER OF JOINTS 44 NUMBER OF MEMBERS 68
NUMBER OF PLATES 0 NUMBER OF SOLIDS 0
NUMBER OF SURFACES 0 NUMBER OF SUPPORTS 12
Using 64-bit analysis engine.
SOLVER USED IS THE OUT-OF-CORE BASIC SOLVER
ORIGINAL/FINAL BAND-WIDTH= 36/ 9/ 102 DOF
TOTAL PRIMARY LOAD CASES = 1, TOTAL DEGREES OF FREEDOM = 102
TOTAL LOAD COMBINATION CASES = 0 SO FAR.
SIZE OF STIFFNESS MATRIX = 11 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.2/ 89566.1 MB
SOFT STORY CHECK
VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05
-------- ---------- --------------
STORY FL. LEVEL IN METE S T A T U S
----- ----------------- --------------------
XZ
1 4.80 OK OK
2 8.00 OK OK
NOTE : NO SOFT STOREY IS DETECTED.
***********************************************************
**
* X DIRECTION : Ta = 0.348 Tb = 0.587 Tuser = 0.000 *
* T = 0.348, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1941 x 2295.53 = 445.60 KN *
**
***********************************************************
************************************************************************
***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.
TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
DYNAMIC ECCENTRICITY APPLIED = DEC - 1
LOAD NO.: 1 DIRECTION : X UNIT - METE
STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC.
----- ----- --------------- --------------- ---------------
XZXZXZ
dec + aec dec + aec
1 4.80 0.00 0.00 0.40 0.70 0.00 0.70
2 8.00 0.00 0.00 0.40 0.70 0.00 0.70
************************************************************************
85. CHANGE
86. LOAD 2 LOADTYPE SEISMIC TITLE EZ
87. UBC LOAD Z 1 DEC 1 ACC 0.05
88. PERFORM ANALYSIS
SOFT STORY CHECK
VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05
-------- ---------- --------------
STORY FL. LEVEL IN METE S T A T U S
----- ----------------- --------------------
XZ
1 4.80 OK OK
2 8.00 OK OK
NOTE : NO SOFT STOREY IS DETECTED.
***********************************************************
**
* Z DIRECTION : Ta = 0.348 Tb = 0.565 Tuser = 0.000 *
* T = 0.348, LOAD FACTOR = 1.000 *
* UBC TYPE = 97 *
* UBC FACTOR V = 0.1941 x 2295.53 = 445.60 KN *
**
***********************************************************
************************************************************************
***NOTE: SEISMIC LOAD IS ACTING AT CENTER OF MASS FOR RIGID DIAPHRAGM.
TORSION FROM STATIC ECCENTRICITY (esi) IS INCLUDED IN ANALYSIS.
DYNAMIC ECCENTRICITY APPLIED = DEC - 1
LOAD NO.: 2 DIRECTION : Z UNIT - METE
STORY LEVEL DYN. ECC. (dec) ACC. ECC. (aec) DESIGN ECC.
----- ----- --------------- --------------- ---------------
XZXZXZ
dec + aec dec + aec
1 4.80 0.00 0.00 0.40 0.70 0.40 0.00
2 8.00 0.00 0.00 0.40 0.70 0.40 0.00
************************************************************************
89. CHANGE
90. LOAD 3 LOADTYPE DEAD TITLE DL
91. REFERENCE LOAD
92. R1 1.0
93. LOAD 4 LOADTYPE LIVE TITLE LL
94. FLOOR LOAD
95. _2W2F FLOAD -1.9 GY
**NOTE** about Floor/OneWay Loads/Weights.
Please note that depending on the shape of the floor you may
have to break up the FLOOR/ONEWAY LOAD into multiple commands.
For details please refer to Technical Reference Manual
Section 5.32.4.2 Note d and/or "5.32.4.3 Note f.
**NOTE** about FLOOR GROUP command
All floor panels in a floor group should lie in a single plane.
If not lying in a single plane break single FLOOR GROUP
command into multiple FLOOR GROUP commands where each
floor group lie in a single plane / height.
96. MEMBER LOAD
97. 50 TO 53 87 88 UNI GY -1.9
98. LOAD COMB 40 GENERATED NSCP 2015 DRIFT 1
99. 3 1.2 4 1.2 1 1.0
100. LOAD COMB 41 GENERATED NSCP 2015 DRIFT 2
E:\MURSprojFiles\a.)SKSU Project\1. SKSU infra porjects\Isulan\2023_Engineering Laboratory 5M\Staadpro\Engeering_LAB.anl
Thursday, 4 May 2023 9:36 AM
STAAD SPACE -- PAGE NO. 7
101. 3 1.2 4 1.2 2 1.0
102. LOAD COMB 42 GENERATED NSCP 2015 DRIFT 3
103. 3 1.2 4 1.2 1 -1.0
104. LOAD COMB 43 GENERATED NSCP 2015 DRIFT 4
105. 3 1.2 4 1.2 2 -1.0
106. LOAD COMB 44 GENERATED NSCP 2015 DRIFT 5
107. 3 0.9 4 0.9 1 1.0
108. LOAD COMB 45 GENERATED NSCP 2015 DRIFT 6
109. 3 0.9 4 0.9 2 1.0
110. LOAD COMB 46 GENERATED NSCP 2015 DRIFT 7
111. 3 0.9 4 0.9 1 -1.0
112. LOAD COMB 47 GENERATED NSCP 2015 DRIFT 8
113. 3 0.9 4 0.9 2 -1.0
114. LOAD COMB 13 GENERATED NSCP 2015 CONCRETE DESIGN 1
115. 3 1.4
116. LOAD COMB 14 GENERATED NSCP 2015 CONCRETE DESIGN 2
117. 3 1.42 4 0.5 1 1.25
118. LOAD COMB 15 GENERATED NSCP 2015 CONCRETE DESIGN 3
119. 3 1.42 4 0.5 2 1.25
120. LOAD COMB 16 GENERATED NSCP 2015 CONCRETE DESIGN 4
121. 3 1.42 4 0.5 1 -1.25
122. LOAD COMB 17 GENERATED NSCP 2015 CONCRETE DESIGN 5
123. 3 1.42 4 0.5 2 -1.25
124. LOAD COMB 18 GENERATED NSCP 2015 CONCRETE DESIGN 6
125. 3 1.2 4 1.6
126. LOAD COMB 19 GENERATED NSCP 2015 CONCRETE DESIGN 7
127. 3 1.42 1 1.25
128. LOAD COMB 20 GENERATED NSCP 2015 CONCRETE DESIGN 8
129. 3 1.42 2 1.25
130. LOAD COMB 21 GENERATED NSCP 2015 CONCRETE DESIGN 9
131. 3 1.42 1 -1.25
132. LOAD COMB 22 GENERATED NSCP 2015 CONCRETE DESIGN 10
133. 3 1.42 2 -1.25
134. LOAD COMB 23 GENERATED NSCP 2015 CONCRETE DESIGN 11
135. 3 0.68 1 1.25
136. LOAD COMB 24 GENERATED NSCP 2015 CONCRETE DESIGN 12
137. 3 0.68 2 1.25
138. LOAD COMB 25 GENERATED NSCP 2015 CONCRETE DESIGN 13
139. 3 0.68 1 -1.25
140. LOAD COMB 26 GENERATED NSCP 2015 CONCRETE DESIGN 14
141. 3 0.68 2 -1.25
142. LOAD COMB 27 GENERATED NSCP 2015 NSCP 203.4.2 1
143. 3 1.0 4 1.0
144. LOAD COMB 28 GENERATED NSCP 2015 NSCP 203.4.2 2
145. 3 1.0 4 0.75 1 0.535
146. LOAD COMB 29 GENERATED NSCP 2015 NSCP 203.4.2 3
147. 3 1.0 4 0.75 2 0.535
148. LOAD COMB 30 GENERATED NSCP 2015 NSCP 203.4.2 4
149. 3 1.0 4 0.75 1 -0.535
150. LOAD COMB 31 GENERATED NSCP 2015 NSCP 203.4.2 5
151. 3 1.0 4 0.75 2 -0.535
152. LOAD COMB 32 GENERATED NSCP 2015 NSCP 203.4.2 6
153. 3 1.0 1 0.7
154. LOAD COMB 33 GENERATED NSCP 2015 NSCP 203.4.2 7
155. 3 1.0 2 0.7
156. LOAD COMB 34 GENERATED NSCP 2015 NSCP 203.4.2 8
157. 3 1.0 1 -0.7
158. LOAD COMB 35 GENERATED NSCP 2015 NSCP 203.4.2 9
159. 3 1.0 2 -0.7
160. LOAD COMB 36 GENERATED NSCP 2015 NSCP 203.4.2 10
161. 3 1.0 4 1.0 1 0.71
162. LOAD COMB 37 GENERATED NSCP 2015 NSCP 203.4.2 11
163. 3 1.0 4 1.0 2 0.71
164. LOAD COMB 38 GENERATED NSCP 2015 NSCP 203.4.2 12
165. 3 1.0 4 1.0 1 -0.71
166. LOAD COMB 39 GENERATED NSCP 2015 NSCP 203.4.2 13
167. 3 1.0 4 1.0 2 -0.71
168. PERFORM ANALYSIS
SOFT STORY CHECK
VERTICAL STRUCTURAL IRREGULARITIES : SOFT STORY CHECK - ASCE/SEI 7-05
-------- ---------- --------------
STORY FL. LEVEL IN METE S T A T U S
----- ----------------- --------------------
XZ
1 4.80 OK OK
2 8.00 OK OK
NOTE : NO SOFT STOREY IS DETECTED.
169. LOAD LIST 40 TO 47
170. PRINT STORY DRIFT 0.004200
STORY DRIFT 0.004200
STORY HEIGHT LOAD AVG. DISP(CM ) DRIFT(CM ) RATIO STATUS
------------------------------------------------------------------------------------------
(METE) X Z X Z
BASE= 0.00 ALLOW. DRIFT = L / 238
1 0.00 40 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
41 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
42 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
43 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
44 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
45 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
46 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
47 0.0000 0.0000 0.0000 0.0000 L /999999 PASS
2 4.80 40 1.5365 0.0887 1.5365 0.0887 L / 312 PASS
41 -0.0065 1.5525 0.0065 1.5525 L / 309 PASS
42 -1.5143 0.0887 1.5143 0.0887 L / 317 PASS
43 0.0288 -1.3751 0.0288 1.3751 L / 349 PASS
44 1.5337 0.0665 1.5337 0.0665 L / 313 PASS
45 -0.0093 1.5303 0.0093 1.5303 L / 313 PASS
46 -1.5170 0.0665 1.5170 0.0665 L / 316 PASS
47 0.0260 -1.3973 0.0260 1.3973 L / 343 PASS
3 8.00 40 2.2074 0.2057 0.6709 0.1170 L / 477 PASS
41 -0.0028 2.2743 0.0037 0.7218 L / 443 PASS
42 -2.1865 0.2057 0.6722 0.1170 L / 476 PASS
43 0.0237 -1.8630 0.0050 0.4879 L / 656 PASS
44 2.2048 0.1543 0.6711 0.0877 L / 477 PASS
45 -0.0054 2.2229 0.0039 0.6926 L / 462 PASS
46 -2.1891 0.1542 0.6720 0.0877 L / 476 PASS
47 0.0211 -1.9144 0.0049 0.5171 L / 619 PASS
171. PRINT DIA CR
DIA CR
************************************************************
CENTRE OF RIGIDITY UNIT - METE
------------------ -----------
DIAPHRAM FL. LEVEL X-COORDINATE Z-COORDINATE
1 4.800 4.000 6.819
2 8.000 4.000 6.974
************************************************************
172. LOAD LIST 13 TO 39
173. START CONCRETE DESIGN
CONCRETE DESIGN
174. CODE ACI 2011
175. CLB 0.04 ALL
176. CLS 0.04 ALL
177. CLT 0.04 ALL
178. FC 21000 ALL
179. FYMAIN 275000 ALL
180. FYSEC 275000 ALL
181. MAXMAIN 20 MEMB 21 TO 32 35 TO 53 55 TO 66 86 TO 88
182. MAXMAIN 16 MEMB 69 TO 85 89 TO 93
183. MINMAIN 16 ALL
184. MINSEC 10 ALL
185. TRACK 2 ALL
186. DESIGN BEAM 38 42 81 TO 83 87 88 91 TO 93
ACI 318-11 BEAM NO. 38 DESIGN RESULTS
=============================================
LEN - 5000. MM FY - 275. FC - 21. MPA, SIZE - 350. X 500. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 4 - 16MM 0. 5000. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 72.83 KN-MET AT 1667.MM, LOAD 15|
| REQD STEEL= 776.MM2, RHO=0.0050, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 78. MMS |
| REQD. DEVELOPMENT LENGTH = 356. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 97015.2 cm^4
2 440. 5 - 20MM 0. 2596. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 135.97 KN-MET AT 0.MM, LOAD 17|
| REQD STEEL= 1338.MM2, RHO=0.0087, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 45./ 58. MMS |
| REQD. DEVELOPMENT LENGTH = 754. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 161045.2 cm^4
3 440. 6 - 20MM 2195. 5000. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 166.39 KN-MET AT 5000.MM, LOAD 15|
| REQD STEEL= 1667.MM2, RHO=0.0108, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 45./ 46. MMS |
| REQD. DEVELOPMENT LENGTH = 943. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 183808.3 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 511./ 1353. 54./ 136. 24/ 17
417. 532./ 880. 56./ 91. 24/ 17
833. 556./ 494. 58./ 52. 20/ 26
1250. 659./ 276. 69./ 29. 15/ 26
1667. 700./ 89. 73./ 10. 15/ 26
2083. 665./ 0. 69./ 0. 15/ 0
2500. 551./ 0. 58./ 0. 15/ 0
2917. 520./ 0. 55./ 0. 17/ 0
E:\MURSprojFiles\a.)SKSU Project\1. SKSU infra porjects\Isulan\2023_Engineering Laboratory 5M\Staadpro\Engeering_LAB.anl
Thursday, 4 May 2023 9:36 AM
STAAD SPACE -- PAGE NO. 12
3333. 491./ 65. 52./ 7. 17/ 24
3750. 388./ 279. 41./ 30. 17/ 24
4167. 342./ 645. 36./ 67. 26/ 15
4583. 313./ 1127. 33./ 115. 26/ 15
5000. 264./ 1687. 28./ 166. 26/ 15
B E A M N O. 38 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 66.86 KNS Vc= 125.22 KNS Vs= 0.00 KNS
Tu= 0.47 KN-MET Tc= 5.1 KN-MET Ts= 0.0 KN-MET LOAD 13
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 221. MM C/C FOR 2060. MM
AT END SUPPORT - Vu= 81.09 KNS Vc= 121.49 KNS Vs= 0.00 KNS
Tu= 0.47 KN-MET Tc= 5.1 KN-MET Ts= 0.0 KN-MET LOAD 13
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 221. MM C/C FOR 2060. MM

ACI 318-11 BEAM NO. 42 DESIGN RESULTS

=============================================
LEN - 5000. MM FY - 275. FC - 21. MPA, SIZE - 350. X 500. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 4 - 16MM 0. 5000. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 56.91 KN-MET AT 2083.MM, LOAD 15|
| REQD STEEL= 711.MM2, RHO=0.0046, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 78. MMS |
| REQD. DEVELOPMENT LENGTH = 356. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 97015.2 cm^4
2 440. 5 - 20MM 0. 2596. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 153.25 KN-MET AT 0.MM, LOAD 17|
| REQD STEEL= 1523.MM2, RHO=0.0099, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 45./ 58. MMS |
| REQD. DEVELOPMENT LENGTH = 754. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 161045.2 cm^4
3 440. 5 - 20MM 2195. 5000. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 133.19 KN-MET AT 5000.MM, LOAD 15|
| REQD STEEL= 1309.MM2, RHO=0.0085, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 45./ 58. MMS |
| REQD. DEVELOPMENT LENGTH = 754. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 161045.2 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 175./ 1541. 19./ 153. 24/ 17
417. 260./ 1007. 28./ 103. 24/ 17
833. 319./ 563. 34./ 59. 24/ 17
1250. 403./ 255. 43./ 27. 15/ 26
1667. 510./ 73. 54./ 8. 15/ 26
2083. 543./ 0. 57./ 0. 15/ 0
2500. 498./ 0. 52./ 0. 15/ 0
2917. 512./ 0. 54./ 0. 17/ 0
3333. 503./ 1. 53./ 0. 17/ 24
3750. 420./ 171. 44./ 18. 17/ 24
4167. 309./ 415. 33./ 44. 26/ 15
4583. 261./ 827. 28./ 85. 26/ 15
5000. 186./ 1324. 20./ 133. 26/ 15
B E A M N O. 42 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 84.79 KNS Vc= 121.57 KNS Vs= 0.00 KNS
Tu= 1.01 KN-MET Tc= 5.1 KN-MET Ts= 0.0 KN-MET LOAD 13
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 221. MM C/C FOR 2060. MM
AT END SUPPORT - Vu= 79.24 KNS Vc= 123.83 KNS Vs= 0.00 KNS
Tu= 1.01 KN-MET Tc= 5.1 KN-MET Ts= 0.0 KN-MET LOAD 13
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 221. MM C/C FOR 2060. MM

ACI 318-11 BEAM NO. 81 DESIGN RESULTS

=============================================
LEN - 2000. MM FY - 275. FC - 21. MPA, SIZE - 300. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 3 - 16MM 0. 2000. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 39.45 KN-MET AT 0.MM, LOAD 15|
| REQD STEEL= 575.MM2, RHO=0.0066, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 92. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 29958.8 cm^4
2 292. 4 - 16MM 0. 2000. YES YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 49.30 KN-MET AT 2000.MM, LOAD 15|
| REQD STEEL= 729.MM2, RHO=0.0083, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 61. MMS |
| REQD. DEVELOPMENT LENGTH = 453. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 37322.2 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 589./ 466. 39./ 32. 15/ 26
167. 492./ 381. 33./ 26. 15/ 26
333. 393./ 299. 27./ 21. 15/ 26
500. 293./ 220. 20./ 15. 15/ 26
667. 192./ 144. 13./ 10. 15/ 26
833. 89./ 70. 6./ 5. 15/ 26
1000. 2./ 17. 0./ 1. 23/ 21
1167. 72./ 123. 5./ 9. 26/ 20
1333. 141./ 236. 10./ 16. 26/ 20
1500. 210./ 354. 15./ 24. 26/ 20
1667. 278./ 478. 19./ 32. 26/ 15
1833. 346./ 609. 24./ 41. 26/ 15
2000. 413./ 747. 28./ 49. 26/ 15
B E A M N O. 81 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 38.88 KNS Vc= 67.28 KNS Vs= 0.00 KNS
Tu= 1.26 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 15
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 146. MM C/C FOR 710. MM
AT END SUPPORT - Vu= 49.88 KNS Vc= 67.51 KNS Vs= 0.00 KNS
Tu= 1.26 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 15
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 146. MM C/C FOR 710. MM

ACI 318-11 BEAM NO. 82 DESIGN RESULTS

=============================================
LEN - 2000. MM FY - 275. FC - 21. MPA, SIZE - 300. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 4 - 16MM 0. 1099. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 42.15 KN-MET AT 0.MM, LOAD 15|
| REQD STEEL= 617.MM2, RHO=0.0070, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 61. MMS |
| REQD. DEVELOPMENT LENGTH = 453. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 37322.2 cm^4
2 58. 3 - 16MM 831. 2000. NO YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 24.98 KN-MET AT 2000.MM, LOAD 26|
| REQD STEEL= 439.MM2, RHO=0.0050, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 92. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 29958.8 cm^4
3 292. 4 - 16MM 0. 2000. YES YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 51.91 KN-MET AT 2000.MM, LOAD 15|
| REQD STEEL= 771.MM2, RHO=0.0088, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 61. MMS |
| REQD. DEVELOPMENT LENGTH = 453. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 37322.2 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 632./ 418. 42./ 28. 15/ 26
167. 517./ 346. 35./ 24. 15/ 26
333. 403./ 276. 27./ 19. 15/ 26
500. 290./ 208. 20./ 14. 15/ 26
667. 178./ 141. 12./ 10. 15/ 26
833. 68./ 81. 5./ 6. 24/ 22
1000. 0./ 47. 0./ 3. 0/ 20
1167. 50./ 160. 4./ 11. 26/ 20
1333. 113./ 277. 8./ 19. 26/ 20
1500. 176./ 398. 12./ 27. 26/ 20
1667. 239./ 524. 17./ 35. 26/ 20
1833. 302./ 655. 21./ 44. 26/ 20
2000. 365./ 790. 25./ 52. 26/ 15
B E A M N O. 82 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 44.53 KNS Vc= 66.69 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 15
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 146. MM C/C FOR 710. MM
AT END SUPPORT - Vu= 49.52 KNS Vc= 66.26 KNS Vs= 0.00 KNS
Tu= 0.01 KN-MET Tc= 2.4 KN-MET Ts= 0.0 KN-MET LOAD 15
NO STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 146. MM C/C FOR 710. MM

ACI 318-11 BEAM NO. 83 DESIGN RESULTS

=============================================
LEN - 2000. MM FY - 275. FC - 21. MPA, SIZE - 300. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 3 - 16MM 0. 2000. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 39.75 KN-MET AT 0.MM, LOAD 15|
| REQD STEEL= 580.MM2, RHO=0.0066, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 92. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 29958.8 cm^4
2 292. 4 - 16MM 0. 2000. YES YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 49.67 KN-MET AT 2000.MM, LOAD 15|
| REQD STEEL= 735.MM2, RHO=0.0084, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 61. MMS |
| REQD. DEVELOPMENT LENGTH = 453. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 37322.2 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 594./ 406. 40./ 28. 15/ 26
167. 496./ 332. 33./ 23. 15/ 26
333. 396./ 260. 27./ 18. 15/ 26
500. 295./ 191. 20./ 13. 15/ 26
667. 193./ 124. 13./ 9. 15/ 26
833. 89./ 60. 6./ 4. 15/ 26
1000. 2./ 17. 0./ 1. 25/ 19
1167. 63./ 125. 4./ 9. 26/ 20
1333. 123./ 238. 9./ 16. 26/ 20
1500. 182./ 357. 13./ 24. 26/ 20
1667. 240./ 482. 17./ 33. 26/ 15
1833. 298./ 614. 20./ 41. 26/ 15
2000. 354./ 753. 24./ 50. 26/ 15
B E A M N O. 83 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 9.06 KNS Vc= 66.97 KNS Vs= 0.00 KNS
Tu= 2.82 KN-MET Tc= 2.4 KN-MET Ts= 3.8 KN-MET LOAD 14
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 710. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.38 SQ.CM.
AT END SUPPORT - Vu= 20.06 KNS Vc= 67.69 KNS Vs= 0.00 KNS
Tu= 2.82 KN-MET Tc= 2.4 KN-MET Ts= 3.8 KN-MET LOAD 14
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 710. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 1.38 SQ.CM.

ACI 318-11 BEAM NO. 87 DESIGN RESULTS

=============================================
LEN - 4297. MM FY - 275. FC - 21. MPA, SIZE - 350. X 450. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 6 - 16MM 0. 4297. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 100.37 KN-MET AT 3939.MM, LOAD 16|
| REQD STEEL= 1103.MM2, RHO=0.0080, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 47. MMS |
| REQD. DEVELOPMENT LENGTH = 593. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 101986.6 cm^4
2 392. 4 - 16MM 0. 1883. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 55.45 KN-MET AT 0.MM, LOAD 16|
| REQD STEEL= 688.MM2, RHO=0.0050, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 78. MMS |
| REQD. DEVELOPMENT LENGTH = 356. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 74500.8 cm^4
3 392. 2 - 16MM 3667. 4297. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 23.55 KN-MET AT 4297.MM, LOAD 14|
| REQD STEEL= 327.MM2, RHO=0.0024, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 234. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42063.6 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 152./ 601. 14./ 55. 23/ 16
358. 159./ 444. 15./ 41. 23/ 16
716. 167./ 289. 16./ 27. 23/ 16
1074. 189./ 152. 18./ 14. 14/ 25
1432. 258./ 63. 24./ 6. 14/ 25
1790. 327./ 0. 31./ 0. 14/ 0
2149. 397./ 0. 37./ 0. 14/ 0
2507. 483./ 0. 45./ 0. 18/ 0
2865. 629./ 0. 58./ 0. 16/ 0
3223. 790./ 0. 72./ 0. 16/ 0
3581. 955./ 0. 86./ 0. 16/ 0
3939. 1123./ 0. 100./ 0. 16/ 0
4297. 91./ 250. 9./ 24. 25/ 14
B E A M N O. 87 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 17.86 KNS Vc= 118.20 KNS Vs= 0.00 KNS
Tu= 24.76 KN-MET Tc= 4.4 KN-MET Ts= 33.0 KN-MET LOAD 14
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 16 MM 2-LEGGED STIRRUPS AT 155. MM C/C FOR 1759. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 9.36 SQ.CM.
AT END SUPPORT - Vu= 17.86 KNS Vc= 101.14 KNS Vs= 0.00 KNS
Tu= 21.14 KN-MET Tc= 4.4 KN-MET Ts= 28.2 KN-MET LOAD 14
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 155. MM C/C FOR 1759. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 7.99 SQ.CM.

ACI 318-11 BEAM NO. 88 DESIGN RESULTS

=============================================
LEN - 4314. MM FY - 275. FC - 21. MPA, SIZE - 350. X 450. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 4 - 16MM 0. 1735. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 52.70 KN-MET AT 0.MM, LOAD 14|
| REQD STEEL= 688.MM2, RHO=0.0050, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 78. MMS |
| REQD. DEVELOPMENT LENGTH = 356. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 74500.8 cm^4
2 58. 2 - 16MM 3844. 4314. NO YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 24.17 KN-MET AT 4314.MM, LOAD 16|
| REQD STEEL= 336.MM2, RHO=0.0025, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 234. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 42063.6 cm^4
3 392. 6 - 16MM 0. 4314. YES YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 100.27 KN-MET AT 3954.MM, LOAD 14|
| REQD STEEL= 1102.MM2, RHO=0.0080, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 47. MMS |
| REQD. DEVELOPMENT LENGTH = 593. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 101986.6 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 571./ 157. 53./ 15. 14/ 25
359. 416./ 163. 39./ 15. 14/ 25
719. 265./ 169. 25./ 16. 14/ 25
1078. 139./ 198. 13./ 19. 23/ 16
1438. 51./ 264. 5./ 25. 23/ 16
1797. 0./ 331. 0./ 31. 0/ 16
2157. 0./ 398. 0./ 37. 0/ 16
2516. 0./ 487. 0./ 45. 0/ 18
2876. 0./ 636. 0./ 59. 0/ 14
3235. 0./ 795. 0./ 72. 0/ 14
3595. 0./ 957. 0./ 86. 0/ 14
3954. 0./ 1122. 0./ 100. 0/ 14
4314. 257./ 81. 24./ 8. 16/ 23
B E A M N O. 88 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 17.11 KNS Vc= 104.80 KNS Vs= 0.00 KNS
Tu= 25.67 KN-MET Tc= 4.4 KN-MET Ts= 34.2 KN-MET LOAD 16
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 16 MM 2-LEGGED STIRRUPS AT 155. MM C/C FOR 1767. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 9.70 SQ.CM.
AT END SUPPORT - Vu= 17.11 KNS Vc= 99.77 KNS Vs= 0.00 KNS
Tu= 21.24 KN-MET Tc= 4.4 KN-MET Ts= 28.3 KN-MET LOAD 16
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 155. MM C/C FOR 1767. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 8.03 SQ.CM.

`
ACI 318-11 BEAM NO. 91 DESIGN RESULTS
=============================================
LEN - 2000. MM FY - 275. FC - 21. MPA, SIZE - 300. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 2 - 16MM 1608. 2000. NO YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 8.87 KN-MET AT 2000.MM, LOAD 19|
| REQD STEEL= 165.MM2, RHO=0.0019, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 184. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 21673.1 cm^4
2 292. 5 - 16MM 0. 2000. YES YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 54.88 KN-MET AT 0.MM, LOAD 19|
| REQD STEEL= 818.MM2, RHO=0.0093, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 46. MMS |
| REQD. DEVELOPMENT LENGTH = 603. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 43976.3 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 0./ 839. 0./ 55. 0/ 19
167. 0./ 743. 0./ 49. 0/ 21
333. 0./ 651. 0./ 43. 0/ 21
500. 0./ 561. 0./ 38. 0/ 21
667. 0./ 475. 0./ 32. 0/ 21
833. 0./ 392. 0./ 27. 0/ 21
1000. 0./ 311. 0./ 21. 0/ 16
1167. 0./ 233. 0./ 16. 0/ 16
1333. 0./ 158. 0./ 11. 0/ 16
1500. 0./ 85. 0./ 6. 0/ 16
1667. 0./ 15. 0./ 1. 0/ 16
1833. 58./ 0. 4./ 0. 19/ 0
2000. 127./ 0. 9./ 0. 19/ 0
B E A M N O. 91 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 34.17 KNS Vc= 63.97 KNS Vs= 0.00 KNS
Tu= 12.62 KN-MET Tc= 2.4 KN-MET Ts= 16.8 KN-MET LOAD 16
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 710. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 6.20 SQ.CM.
AT END SUPPORT - Vu= 29.18 KNS Vc= 66.18 KNS Vs= 0.00 KNS
Tu= 12.62 KN-MET Tc= 2.4 KN-MET Ts= 16.8 KN-MET LOAD 16
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 710. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 6.20 SQ.CM.

ACI 318-11 BEAM NO. 92 DESIGN RESULTS

=============================================
LEN - 4297. MM FY - 275. FC - 21. MPA, SIZE - 300. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 5 - 16MM 0. 4297. YES YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 63.03 KN-MET AT 3939.MM, LOAD 16|
| REQD STEEL= 952.MM2, RHO=0.0109, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 46. MMS |
| REQD. DEVELOPMENT LENGTH = 603. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 43976.3 cm^4
2 292. 3 - 16MM 0. 1779. YES NO
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 34.35 KN-MET AT 0.MM, LOAD 16|
| REQD STEEL= 497.MM2, RHO=0.0057, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 92. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 29958.8 cm^4
3 292. 2 - 16MM 3771. 4297. NO YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 9.86 KN-MET AT 4297.MM, LOAD 19|
| REQD STEEL= 184.MM2, RHO=0.0021, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 184. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 21673.1 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 73./ 509. 5./ 34. 23/ 16
358. 94./ 373. 7./ 25. 23/ 16
716. 115./ 241. 8./ 17. 23/ 16
1074. 146./ 120. 10./ 8. 19/ 25
1432. 220./ 45. 15./ 3. 19/ 25
1790. 296./ 0. 20./ 0. 19/ 0
2149. 373./ 0. 26./ 0. 19/ 0
2507. 451./ 0. 31./ 0. 19/ 0
2865. 542./ 0. 36./ 0. 16/ 0
3223. 683./ 0. 45./ 0. 16/ 0
3581. 828./ 0. 54./ 0. 16/ 0
3939. 977./ 0. 63./ 0. 16/ 0
4297. 59./ 141. 4./ 10. 25/ 19
B E A M N O. 92 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 14.27 KNS Vc= 79.74 KNS Vs= 0.00 KNS
Tu= 9.98 KN-MET Tc= 2.4 KN-MET Ts= 13.3 KN-MET LOAD 19
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 1859. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 4.90 SQ.CM.
AT END SUPPORT - Vu= 7.94 KNS Vc= 64.30 KNS Vs= 0.00 KNS
Tu= 7.36 KN-MET Tc= 2.4 KN-MET Ts= 9.8 KN-MET LOAD 19
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 1859. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 3.61 SQ.CM.

ACI 318-11 BEAM NO. 93 DESIGN RESULTS

=============================================
LEN - 4314. MM FY - 275. FC - 21. MPA, SIZE - 300. X 350. MMS
LEVEL HEIGHT BAR INFO FROM TO ANCHOR
(MM) (MM) (MM) STA END
_____________________________________________________________________
1 58. 3 - 16MM 0. 1705. YES NO
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 32.24 KN-MET AT 0.MM, LOAD 14|
| REQD STEEL= 465.MM2, RHO=0.0053, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 92. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 29958.8 cm^4
2 58. 2 - 16MM 3969. 4314. NO YES
|----------------------------------------------------------------|
| CRITICAL POS MOMENT= 10.28 KN-MET AT 4314.MM, LOAD 21|
| REQD STEEL= 192.MM2, RHO=0.0022, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 184. MMS |
| REQD. DEVELOPMENT LENGTH = 347. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 21673.1 cm^4
3 292. 5 - 16MM 0. 4314. YES YES
|----------------------------------------------------------------|
| CRITICAL NEG MOMENT= 63.00 KN-MET AT 3954.MM, LOAD 14|
| REQD STEEL= 951.MM2, RHO=0.0109, RHOMX=0.0284 RHOMN=0.0050 |
| MAX/MIN/ACTUAL BAR SPACING= 448./ 41./ 46. MMS |
| REQD. DEVELOPMENT LENGTH = 603. MMS |
|----------------------------------------------------------------|
Cracked Moment of Inertia Iz at above location = 43976.3 cm^4
REQUIRED REINF. STEEL SUMMARY :
-------------------------------
SECTION REINF STEEL(+VE/-VE) MOMENTS(+VE/-VE) LOAD(+VE/-VE)
( MM ) (SQ. MM ) (KNS-MET )
0. 476./ 81. 32./ 6. 14/ 25
359. 344./ 101. 24./ 7. 14/ 25
719. 215./ 122. 15./ 9. 14/ 25
1078. 107./ 161. 8./ 11. 23/ 21
1438. 34./ 233. 2./ 16. 23/ 21
1797. 0./ 307. 0./ 21. 0/ 21
2157. 0./ 382. 0./ 26. 0/ 21
2516. 0./ 458. 0./ 31. 0/ 21
2876. 0./ 551. 0./ 37. 0/ 14
3235. 0./ 689. 0./ 46. 0/ 14
3595. 0./ 830. 0./ 54. 0/ 14
3954. 0./ 977. 0./ 63. 0/ 14
4314. 147./ 52. 10./ 4. 21/ 23
B E A M N O. 93 D E S I G N R E S U L T S - SHEAR
AT START SUPPORT - Vu= 13.78 KNS Vc= 66.64 KNS Vs= 0.00 KNS
Tu= 10.41 KN-MET Tc= 2.4 KN-MET Ts= 13.9 KN-MET LOAD 21
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 12 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 1867. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 5.11 SQ.CM.
AT END SUPPORT - Vu= 7.32 KNS Vc= 63.51 KNS Vs= 0.00 KNS
Tu= 7.07 KN-MET Tc= 2.4 KN-MET Ts= 9.4 KN-MET LOAD 21
STIRRUPS ARE REQUIRED FOR TORSION.
REINFORCEMENT FOR SHEAR IS PER CL.11.5.5.1.
PROVIDE 10 MM 2-LEGGED STIRRUPS AT 118. MM C/C FOR 1867. MM
ADDITIONAL LONGITUDINAL STEEL REQD. FOR TORSIONAL RESISTANCE = 3.47 SQ.CM.

********************END OF BEAM DESIGN**************************

187. DESIGN COLUMN 22 56
ACI 318-11 COLUMN NO. 22 DESIGN RESULTS
ACI 318-11 COLUMN NO. 56 DESIGN RESULTS
===============================================

********************END OF COLUMN DESIGN RESULTS********************

188. CONCRETE TAKE
STAAD SPACE -- PAGE NO. 33
189. END CONCRETE DESIGN
************** CONCRETE TAKE OFF **************
(FOR BEAMS, COLUMNS AND PLATES DESIGNED ABOVE)
NOTE: CONCRETE QUANTITY REPRESENTS VOLUME OF CONCRETE IN BEAMS, COLUMNS, AND PLATES DESIGNED ABOVE.
REINFORCING STEEL QUANTITY REPRESENTS REINFORCING STEEL IN BEAMS AND COLUMNS DESIGNED ABOVE.
REINFORCING STEEL IN PLATES IS NOT INCLUDED IN THE REPORTED QUANTITY.
TOTAL VOLUME OF CONCRETE = 6.1 CU.METER
BAR SIZE WEIGHT
NUMBER (in lbs)
-------- --------
10 232
12 208
16 1036
20 725
------------
*** TOTAL= 2201
190. FINISH