5G RAN Testing

CHALLENGE: CAPTURING THE PROMISES HIGHLIGHTS

OF 5G-RAN
As 5G standards evolve, it is important to perform continuous
• Validate 5G RAN functionality
standards conformance testing to accelerate innovation. Testing
by assessing full protocol stack
5G devices, equipment, and networks with complete confidence
from Layer 1 to Layer 7
requires careful planning, well thought-out test plans, a
performance benchmarking strategy, test automation, and • Functional testing – layer by
reporting. This will eliminate any surprises when accelerating the layer testing – up to 10 UEs
deployment of 5G-related products and services.
• Load testing of 5G-RAN – NSA
5G New Radio (NR) is the new technology specification for an and SA modes
OFDM-based physical air interface. 5G NR is not an evolution of
• Compact footprint with potential
4G (LTE). It is required to achieve the extreme bandwidth, low
to grow up to 4,000 UEs
latency, and massive scalability requirements of 5G. 5G NR is
expected to make wireless broadband performance the same as • Test complex mobility scenarios
wired – “Wireless Fiber” to deliver lower cost per bit.
• Perform service quality
Based on these drivers, here are a few key expectations placed on validation with subscriber
the next-generation of wireless networks: modeling, and multiplay voice,
video, and data traffic
1. Drastic decreases in latency (1ms on radio, <5ms end to end)
generation
and massive improvements in throughput (gigabit speeds per
subscriber) • 3GPP R15, FR1 (Sub6 GHz),
2. Drastic increases in density – one million devices per square up to 4xCC, up to 4x4 MIMO
kilometer • Flexible, modular, and scalable
3. Support for higher-speed mobility – up to 500Km/h to support different split
4. Drastic decreases of energy consumption for terminals (for IoT architecture of 5G-RAN
devices, surviving up to 10 years on a couple of AA batteries)
5. Improvements to geolocation accuracy – less than 1 meter
6. Increases in network flexibility with more automation and
programmability
7. Reducing OPEX costs to one-fifth of today's numbers

MORE AND FASTER

Unlike some prior, more incremental advances in wireless, 5G is not just about more and faster, but more
and faster is part of the story. Enhanced mobile broadband (eMBB) captures much of the more and faster
story, but it is here that the quantity of the more and faster bring about a completion of what started with
earlier 4G deployments like WiMAX – wireless as a replacement for wired connections.

www.ixiacom.com I 915-3859-01-2191 I Rev C Page 1

 DATA SHEET

SOLUTION: 5G NR UE EMULATION FOR FUNCTIONAL LAYER-BY-

LAYER TESTING AND LOAD/SCALE/PERFORMANCE TESTING
Keysight’s XAir3 fixed chassis (appliance) provides 5G NR user equipment (UE) emulation that enables a
powerful Layer 1 to 7 test solution. With complex UE modeling, it offers realistic and easily-configured
traffic models and call patterns. Using IxLoad’s real-world subscriber modeling, testers do not need to be
protocol experts to develop test realism. From a single tool, users can perform capacity tests, detail a cell
throughput, measure voice and video quality, and model a wide variety of mobility scenarios.

PRODUCT CAPABILITIES
• Full-featured 5G NR UE emulation within all FR1 Sub6 GHz bands with 100 MHz bandwidth
• Mobile application modeling with voice, video, and data traffic, including QoE (MOS, PESQ) and
QoS measurements
• Non-standalone (NSA) – Option 3x with potential for 3, 3a, 4, and 7 as per 5G RAN architecture
• Standalone (SA) mode
• Designed for 5G
• Initially NSA, software upgradable to SA
• Uses current gen 4G UE emulation system as LTE anchor
• Baseband + lower MAC-layer functions
• Purpose-built for eMBB, mMTC, and URLLC
• Support for both sub 6GHz and mmWave
• Support for 100, 200, 400MHz bandwidth
• Support for 2x2, 4x4 MIMO
• 4 aggregated carriers, thousands of UEs
• 8xQSFP28 that are capable of eCPRI (10/25G)
• 8x25G links for data-plane IP traffic

Find us at www.ixiacom.com Page 2

 DATA SHEET

XAIR3 PHYSICAL SPECIFICATIONS

XAIR3 BASEBAND FIXED CHASSIS SYSTEM SPECIFICATIONS

Fixed Chassis System • 30.3” (L) x 17.3” (W) x 3.46” (H)

Dimensions
• 770mm (L) x 438.2mm (W) x 88mm (H)

Fixed Chassis System • Hardware only: 74.6 lbs. (33.84 kg)

Weights
• Shipping: 94.5 lbs. (42.86 kg) (1)
(1)
Approximate (includes slides, power cords, sync cables and packaging)

Fixed Chassis System • Operates on 100-240VAC, 50/60Hz.

Electrical Power (2)
• 200-240VAC is single phase.
• Requires (3) power sources when running 100-120VAC, 9 Amps for each
power supply. XAir3 fixed chassis is shipped with (3) 100-125VAC power
cords.
• Requires (2) power sources when running 200-240VAC, 7 Amps for each
power supply. For 200-240VAC power cords, order part number 942-0110
from the Ordering Information section of this datasheet. The kit is
provided at no charge with the purchase of a XAir3 fixed chassis when
200-240VAC is required.
(2)
Note: Power specifications are preliminary and are for reference for
initial facility planning purposes.

Temperature • Operating: 41°F to 95°F (5°C to 35°C)

• Storage: 41°F to 122°F (5°C to 50°C)

Humidity • Operating: 0% to 85%, non-condensing

• Storage: 0% to 85%, non-condensing

Find us at www.ixiacom.com Page 3

 DATA SHEET

X100-5G

• 2U appliance
• Intel 44 cores, 128GB RAM, 480GB SSD, 4 slots
• Runs Ubuntu OS
• 4 PCI Express Slots
• 25GE NICs (2-ports) – must be ordered separately
• 10GE NICs (2-ports) – must be ordered separately

Find us at www.ixiacom.com Page 4

 DATA SHEET

10GE NIC

10GE NIC KEY FEATURES

• Dual SFP+ connectors
• Low-profile standard form factor
• PCI Express 2.0 (up to 5GT/s)
• Intel® QuickData technology
• VMDq, next-generation VMDq, and PC-SIG SR-IOV for virtualized environments
• Load balancing on multiple CPUs
• iSCSI remote boot support
• FCoE
• Support for most network operating systems (NOSs)
• Support both DAC twin axial and LC fiber-optic SR cables
• RoHS compliant 6/6

Find us at www.ixiacom.com Page 5

 DATA SHEET

25GE NIC

25GE NIC KEY FEATURES

• Dual SPF28 connectors
• Low-profile, short length standard form factor
• PCI-E 3.0 x8
• Mellanox ConnectX®-4 Lx EN Ethernet Controller
• Asset management features with thermal sensor
• Hardware offloads for VXLAN, NVGRE, and GENEVE encapsulated traffic
• Low-latency RDMA over converged Ethernet (RoCE)
• PCI-SIG SR-IOV compliant
• Jumbo frames support up to 9.6KB
• PXE support
• Erasure coding offload
• NC-SI for IPMI support
• RoHS compliant 6/6

Find us at www.ixiacom.com Page 6

 DATA SHEET

5G NR RADIOHEAD: RH 400-6000
The XAir3 Module is connected to the gNB device under test (DUT) through a radio frequency (RF)
connection provided by the Ixia 6GHz Wideband Radio. The specifications for this radio are provided in
the table below.

HIGHLIGHTS
• 400MHz to 6GHz frequency range
• FDD/TDD support
• 4x4 MIMO
• Class leading RF timing alignment for OTA test
• 100Mhz instantaneous bandwidth
• TX output power 0dBm (400-2700MHz)
• TX output power -10dBm (2700-5500MHz)
• TX output power -15dBm (5500-5925MHz)
• Support for CPRI V4.2
• CPRI line rates 1-8 supported
• Ambient temperature range 5-50 degree C
• RF connectors SMA
• Low power consumption typical < 80W
• Product Weight 12Kg

GENERAL SPECIFICATIONS

SPECIFICATION VALUE

Bandwidth 100 MHz

Frequency ranges 400-6000MHz

Operating mode FDD/TDD

Number of Tx/Rx paths 4x4 MIMO

Digital baseband I/F CPRI V4.2

Clock reference Recovered from CPRI line rate

Find us at www.ixiacom.com Page 7

 DATA SHEET

Ambient Temperature range 5-50 C

Module RF connectors SMA

Power meters Tx and Rx power meters located at the antenna

Calibration Continuous compensation of quadrature (IQ) imbalance

PSU Spec 100 – 240 VAC, 50-60 Hz; 80W

Replaceable or resettable fuse
Input: IEC-C14

FIBRE OPTIC INTERFACE SPECIFICATION

SPECIFICATION VALUE

Fiber Optic Cable Duplex LC Single Mode

Fiber Wave Length: 1310nm
Fiber Type: 9/125nm

PHYSICAL/ENVIRONMENTAL AND ELECTRICAL SPECIFICATIONS

SPECIFICATION VALUE

Height 1U

Depth Depth 630mm;

Weight/Mass 12kg including removable rails (but with no packaging)

19” Rack connection Tool-less rack supplied with product.

Rail Range: Min = 660mm ; Max = 800mm

Front Panel 8 x SMA RF connectors, female (4 x Rx, 4 x Tx)

LED Panels: see Requirements section for details

Rear Panel 2 x SFP+ ports (bidirectional CPRI), 2x Ethernet

Power Input: IEC-C14
Ground Lug with bolt/washer or equivalent
2 x SMA TDD pulse outputs

Cooling Internal Fan cooling

Find us at www.ixiacom.com Page 8

 DATA SHEET

ELECTRICAL SPECIFICATIONS (AT 25ºC UNLESS OTHERWISE SPECIFIED)

TRANSMIT SPECIFICATIONS

SPECIFICATION VALUE

Tx power (OFDM) TX output power 0dBm (400MHz-2.7GHz)

TX output power -10dBm (2.7-5.5GHz)
TX output power -15dBm (5.5-5.925GHz)

Tx max. power (CW) ≥10dBm (400-2700MHz)

0dBm (2700-5500MHz)
-5dBm (5500-5925MHz)

Tx power meter Wideband power @ antenna

Tx gain range >40dB

Tx gain accuracy 0.25dB

Tx spurious emissions <-45 dBm

EVM <1.2% 400MHz to 2.0GHz;

<1.4% median and 2% peak 2.0GHz to 4.0GHz;
<1.6% median and 3.5% peak 4.0 GHz to 6 GHz

Noise power density <133dBc/Hz @ 10Mhz offset

Tx to Tx isolation >50dB

Tx to Rx isolation >60dB

DAC 16 bit

Gain Flatness (over full bandwidth) 0.8dB

Ripple (over full bandwidth) 0.6dB

RECEIVE SPECIFICATIONS

SPECIFICATION VALUE

Rx power max. (no damage) 30dBm

Rx power meter Wideband power @ antenna

Rx gain range 60dB

Find us at www.ixiacom.com Page 9

 DATA SHEET

Rx gain accuracy 0.25dB

Spurious emissions <-45dBm

Pass band ripple <±1dB

Demodulation Accuracy < 1.1% 400MHz to 2.0 GHz @ 256 QAM

(in terms of EVM ) < 1.5% 2.0GHz to 4.0GHz @ 256 QAM
< 1.5% median and 3.5% peak 4.0GHz to 6.0GHz @ 256 QAM

TIMING ALIGNMENT

SPECIFICATION VALUE

TX Delay Alignment (TX port to any TX port) <=5nS

RX Delay Alignment (RX port to RX port same <=5nS

CPRI link)

RX Path Alignment (variation between <=15nS

antenna)

Delay adjustment +/- 4nS

Delay reporting T12,T2a ad Ta3 per the CPRI Spec

5G NR RADIO CONNECTION ENCLOSURE; SUB 6 GHZ: RCE 350-6000

The Radio Connection Enclosure (RCE 350-6000) simplifies cabling when attaching to DUTs that have a
single port (combined Tx and Rx) per antenna. RCE 350-6000 is a passive device containing all the
cabling and splitter/combiner parts required to transform the Radio Head antenna interface to combined
Tx/Rx antenna ports. Connectors and internal parts are chosen to specifically match the full range of
frequency and power supported by the Radio Head.

Find us at www.ixiacom.com Page 10

 DATA SHEET

Block Diagram:

PHYSICAL/ENVIRONMENTAL AND ELECTRICAL SPECIFICATIONS

SPECIFICATION VALUE
1.72 in [43.7 mm]
Height

Width 19.00 in [482.6 mm]

Depth 15.11 in [383.8 mm]

Weight/Mass 6.7 lbs [3.1 kg]

19” Rack connection Mounting holes (x4) on front panel

Front Panel 8 x SMA RF connectors, female (4 x Rx, 4 x Tx)

Rear Panel 4 x N RF connectors, female

ELECTRICAL SPECIFICATIONS (AT 25ºC UNLESS OTHERWISE SPECIFIED)

SPECIFICATION VALUE

Port Count 4

Bandwidth 350 MHz to 6000 MHz

Isolation per port 17.1 dB

Find us at www.ixiacom.com Page 11

 DATA SHEET

PLATFORM OPTIONS FOR XAIR2 FOR 4G/LTE ANCHOR

VISIT KEYSIGHTCOM.COM FOR MORE INFORMATION ON

IXLOAD PLATFORM OPTIONS

Chassis • XGS-12 HS/SD/HSL Chassis

• XGS-2 HS/SD/HSL Chassis

Load Modules • XAir2

• PerfectStorm

Radio Head 4G Radio Head: Supports all LTE bands with 5/10/15/20 MHz bandwidth

Radio Connection 4G RCE: A passive device containing all the cabling and
Enclosure splitter/combiner parts required to transform the Radio Head antenna
interface to combined Tx/Rx antenna ports

TEST TOPOLOGIES
NSA Mode – eNB and gNB wrap-around - Option 3x or real EPC.

Find us at www.ixiacom.com Page 12

 DATA SHEET

NSA Mode – eNB and gNB-CU wrap-around - Option 3x or real EPC.

Emulated DUT/SUT Emulated

eNB

UE S1U
s
EPC With Option
3X
Or Real EPC

gNB-DU gNB-CU

ORDERING INFORMATION
T8020S – Please contact your local Ixia sales team.

Find us at www.ixiacom.com Page 13