Scribd
Upload
47 views14 pages

Log Sheets

This quality check stage inspection report examines bearings according to various parameters such as length, width, bolt center distances, diameters, and thicknesses. The report checks four plates (A, B, C, D) according to these standardized parameters, noting the specifications and observed values. Any issues with sharp edges, chamfers, or deburred holes are also documented. The inspection aims to ensure the bearings meet specifications for dimensional accuracy before proceeding to the next stage.

Uploaded by

Lokesh Badgujar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
47 views14 pages

Log Sheets

This quality check stage inspection report examines bearings according to various parameters such as length, width, bolt center distances, diameters, and thicknesses. The report checks four plates (A, B, C, D) according to these standardized parameters, noting the specifications and observed values. Any issues with sharp edges, chamfers, or deburred holes are also documented. The inspection aims to ensure the bearings meet specifications for dimensional accuracy before proceeding to the next stage.

Uploaded by

Lokesh Badgujar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 14

QUALITY CHECK STAGE INSPECTION REPORT – BEARINGS

Report No. Work Order No. MS/22-23/ Form No. : Q/F/03 Rev. : 01
Sheet no : 06/06
Customer ROYAL INFRA Qty: 02

Stage of Inspection : Machined Drawing no. : 26797 Capacity Type : TAP No. of Holes: 04 Hole dia: M 20

Stages Parameters Standard Observed Value


Stage I- Date
Dimensional I. D. No. 01 02
Check of a Length of Plate / Outer Dia. 770
Components b Width of Plate 550
c Longitudinal Bolt C/C (PCD) 690
A.
Distribution d Transverse Bolt C/C (PCD) 450
Plate
e Plate Thickness 30
Date
I. D. No.
a Length of Plate / Outer Dia.
b Width of Plate
B.
Distribution c Longitudinal Bolt C/C (PCD)
Plate
d Transverse Bolt C/C (PCD)
e Plate Thickness
Date
I. D. No.
a Length of Plate / Outer Dia.
b Width of Plate
C.
Distribution c Longitudinal Bolt C/C (PCD)
Plate
d Transverse Bolt C/C (PCD)
e Plate Thickness
Date
I. D. No.
a Length of Plate / Outer Dia.
b Width of Plate
D.
Distribution c Longitudinal Bolt C/C (PCD)
Plate
d Transverse Bolt C/C (PCD)
e Plate Thickness
Checked By:
QUALITY CHECK STAGE INSPECTION REPORT – BEARINGS
Report No. of Work Order No.:~ MS/22-23/56 Form No. : Q/F/03 Rev. : 01
Customer M/S. G.R. INFRA Qty: 46 nos.
T.P.=04 Hole T.P.= 19 MM
No. of Holes: dia: B.P.=
Stage of Inspection : Machined Drg. No.:~ 26545 Capacity: 7300 KN Type : FF B.P.= 04 19 MM

Stages Parameters Standard Tolerance Observed Value


Stage I- Date
Dimensional I. D. No.
Check of a Base Effective Length 525
Components b Base Effective Width 525
c Longitudinal Bolt C/C 530
d Transverse Bolt C/C 530
e Inner Diameter 390
A. f Wall Outer Diameter ~ ~ ~ ~ ~ ~
BASE PLATE g Total Thickness 63.28
h Inside Depth 38.28
i Flange Thickness 12
j Radius Of Curvature Inside Pot 593
Date
I. D. No.
a Base Effective Diameter 420
b Diameter Of Groove 390
B. c Depth Of Groove 05
PISTON d Thickness Above Curvature 12
e Radius Of Curvature 585
f MSM Dimension ~ ~ ~ ~ ~ ~ ~
Date
I. D. No.
a Length Of Top plate 850
b Width Of Top plate 525
c Longitudinal Bolt C/C 780
d Transverse Bolt C/C 590
C. e Top Plate Thickness ~ ~ ~ ~ ~ ~ ~
TOP PLATE f Width of Guide Bar ~ ~ ~ ~ ~ ~ ~
g Height of Guide Bar ~ ~ ~ ~ ~ ~ ~
h Guide Bar inside Dimension ~ ~ ~ ~ ~ ~ ~
i Total Plate Thickness 38
j Flange thickness 12
Checked By:
Note: Shot Blasting SA 2 ½ Required. = Found OK NOT OK : Break All Sharp Edge, 2 mm Chamfer, Deburr All Holes
QUALITY CHECK STAGE INSPECTION REPORT – BEARINGS
Report No. of Work Order No.:~ Form No. : Q/F/03 Rev. : 01
Customer M/S. Qty: nos.
T.P.= Hole T.P.=
No. of Holes: dia: B.P.=
Stage of Inspection : Machined Drg. No.:~ Capacity: Type : B.P.=
Stages Parameters Standard Tolerance Observed Value
Stage I- Date
Dimensional I. D. No.
Check of a Base Effective Length
Components b Base Effective Width
c Longitudinal Bolt C/C
d Transverse Bolt C/C
e Inner Diameter
A. f Wall Outer Diameter ~ ~ ~ ~ ~ ~ ~
BASE PLATE g Total Thickness
h Inside Depth
i Flange Thickness
j Radius Of Curvature Inside Pot
Date
I. D. No.
a Base Effective Diameter
b Diameter Of Groove
B. c Depth Of Groove
PISTON d Thickness Above Curvature
e Radius Of Curvature
f MSM Dimension ~ ~ ~ ~ ~ ~ ~
Date
I. D. No.
a Length Of Top plate
b Width Of Top plate
c Longitudinal Bolt C/C
d Transverse Bolt C/C
C. e Top Plate Thickness
TOP PLATE f Width of Guide Bar
g Height of Guide Bar
h Guide Bar inside Dimension
i Total Plate Thickness
j Flange thickness
Checked By:
Note: Shot Blasting SA 2 ½ Required. = Found OK NOT OK : Break All Sharp Edge, 2 mm Chamfer, Deburr All Holes
QUALITY CHECK STAGE INSPECTION REPORT – BEARINGS
Report No. of 02 Work Order No.:~ MS/22-23/102 Form No. : Q/F/03 Rev. : 01
Customer M/S. MONTECARLO LTD. Qty: 12 nos.
T.P.=10 Hole T.P.= 39MM
No. of Holes: dia: B.P.=
Stage of Inspection : Machined Drg. No.:~ 27205 Capacity: 180 MT Type : SG~T B.P.= 10 39MM

Stages Parameters Standard Tolerance Observed Value


Stage I- Date
Dimensional I. D. No.
Check of a Base Effective Length 530
Components b Base Effective Width 530
c Longitudinal Bolt C/C 430
d Transverse Bolt C/C 640
e Inner Diameter 190
A. f Wall Outer Diameter ~ ~ ~ ~ ~ ~ ~
BASE PLATE g Total Thickness 93.12
h Inside Depth 21.12
i Flange Thickness 15
j Radius Of Curvature Inside Pot 293
Date
I. D. No.
a Base Effective Diameter 220
b Diameter Of Groove 190
B. c Depth Of Groove 05
PISTON d Thickness Above Curvature 12
e Radius Of Curvature 285
f MSM Dimension ~ ~ ~ ~ ~ ~ ~
Date
I. D. No.
a Length Of Top plate 550
b Width Of Top plate 750
c Longitudinal Bolt C/C 450
d Transverse Bolt C/C 860
C. e Top Plate Thickness 37
TOP PLATE f Width of Guide Bar 82.5
g Height of Guide Bar 106
h Guide Bar inside Dimension 585
i Total Plate Thickness 143
j Flange thickness 15
Checked By:
Note: Shot Blasting SA 2 ½ Required. = Found OK NOT OK : Break All Sharp Edge, 2 mm Chamfer, Deburr All Holes
QUALITY CHECK STAGE INSPECTION REPORT – BEARINGS
Report No. 01 of 01 Work Order No.:~ Form No. : Q/F/03 Rev. : 01

Customer M/S. Qty: nos.


T.P.= Hole T.P.=
No. of Holes:
Stage of Inspection : Machined Drg. No.:~ Capacity: Type : FX B.P.= dia: B.P.=

Stages Parameters Standard Tolerance Observed Value


Stage I- Date
Dimensional I. D. No.
Check of a Base Effective Diameter
Components b Bolt PCD
c Inner Diameter
d Wall Outer Diameter
e Vertical Face On Outer Dia.
A.
BASE PLATE f Total Thickness
g Inside Depth
h Flange Thickness
i Radius Of Curvature Inside Pot
Date
I. D. No.
a Base Effective Diameter
b Diameter Of Groove
B. c Depth Of Groove
PISTON d Thickness Above Curvature
e Radius Of Curvature
f MSM Dimension ~ ~ ~ ~ ~ ~
Date
I. D. No.
a Base Effective Diameter
b Outer Diameter
c Bolt PCD
d Top Plate Thickness
C.
TOP PLATE e Width of Guide Bar
f Height of Guide Bar
g Guide Bar inside Dimension
h Total Plate Thickness
i Flange thickness
Checked By:
Note: Shot Blasting SA 2 ½ Required. = Found OK NOT OK : Break All Sharp Edge, 2 mm Chamfer, Deburr All Holes
QUALITY CHECK STAGE INSPECTION REPORT – BEARINGS
Report No. 01 of 01 Work Order No.:~ Form No. : Q/F/03 Rev. : 01

Customer M/S. Qty: nos.


T.P.= Hole T.P.=
No. of Holes:
Stage of Inspection : Machined Drg. No.:~ Capacity: Type : FX B.P.= dia: B.P.=

Stages Parameters Standard Tolerance Observed Value


Stage I- Date
Dimensional I. D. No.
Check of a Base Effective Diameter
Components b Bolt PCD
c Inner Diameter
d Wall Outer Diameter
e Vertical Face On Outer Dia.
A.
BASE PLATE f Total Thickness
g Inside Depth
h Flange Thickness
i Radius Of Curvature Inside Pot
Date
I. D. No.
a Base Effective Diameter
b Diameter Of Groove
B. c Depth Of Groove
PISTON d Thickness Above Curvature
e Radius Of Curvature
f MSM Dimension ~ ~ ~ ~ ~ ~ ~
Date
I. D. No.
a Length Of Top plate
b Width Of Top plate
c Longitudinal Bolt C/C
d Transverse Bolt C/C
C. e Top Plate Thickness
TOP PLATE f Width of Guide Bar
g Height of Guide Bar
h Guide Bar inside Dimension
i Total Plate Thickness
J Flange thickness
Checked By:
Note: Shot Blasting SA 2 ½ Required. = Found OK NOT OK : Break All Sharp Edge, 2 mm Chamfer, Deburr All Holes
QUALITY CHECK STAGE INSPECTION REPORT – BEARINGS
Report No. of 02 Work Order No.:~ MS/22-23/56 Form No. : Q/F/03 Rev. : 01
Customer M/S. G.R. INFRA Qty: 23 nos.
T.P.=08 Hole T.P.= 39MM
No. of Holes: dia: B.P.=
Stage of Inspection : Machined Drg. No.:~ 27756 Capacity: 7300 KN Type : FX B.P.= 08 39MM

Stages Parameters Standard Tolerance Observed Value


Stage I- Date
Dimensional I. D. No.
Check of a Base Effective Length 670
Components b Base Effective Width 670
c Longitudinal Bolt C/C 480
d Transverse Bolt C/C 860
e Inner Diameter 390
A. f Wall Outer Diameter 458.5 ~ ~ ~ ~ ~ ~
BASE PLATE g Total Thickness 63.28
h Inside Depth 38.28
i Flange Thickness 15
j Radius Of Curvature Inside Pot 593
Date
I. D. No.
a Base Effective Diameter 420
b Diameter Of Groove 390
B. c Depth Of Groove 05
PISTON d Thickness Above Curvature 12
e Radius Of Curvature 585
f MSM Dimension ~ ~ ~ ~ ~ ~
Date
I. D. No.
a Base Effective Diameter 670
b Outer Diameter 940
c Longitudinal Bolt C/C 294/500
d Transverse Bolt C/C 628/751
C. e Top Plate Thickness 38
TOP PLATE
f Width of Guide Bar 105
g Height of Guide Bar 41
h Guide Bar inside Dimension 460
i Total Plate Thickness 79
j Flange thickness 15
Checked By:
Note: Shot Blasting SA 2 ½ Required. = Found OK NOT OK : Break All Sharp Edge, 2 mm Chamfer, Deburr All Holes

You might also like