Scribd
Upload
25 views

Batch Rectification Lab-Note

1. Batch rectification is performed when the mass flow of feed is too low, more than two products need to be separated, the feed concentration is unstable, or good separation is needed with relatively few theoretical plates. 2. In batch rectification, the entire feed is added to the reboiler at once and vapor is continuously evaporated while liquid from reflux and vapor flow countercurrently. Rectification can be performed in constant reflux ratio or constant distillate composition modes. 3. An experiment is described to perform batch rectification on a glass bubble plate column containing a n-heptane-toluene mixture using either constant reflux ratio or constant distillate composition operating modes while measuring temperatures

Uploaded by

Alina Tilek
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
25 views

Batch Rectification Lab-Note

1. Batch rectification is performed when the mass flow of feed is too low, more than two products need to be separated, the feed concentration is unstable, or good separation is needed with relatively few theoretical plates. 2. In batch rectification, the entire feed is added to the reboiler at once and vapor is continuously evaporated while liquid from reflux and vapor flow countercurrently. Rectification can be performed in constant reflux ratio or constant distillate composition modes. 3. An experiment is described to perform batch rectification on a glass bubble plate column containing a n-heptane-toluene mixture using either constant reflux ratio or constant distillate composition operating modes while measuring temperatures

Uploaded by

Alina Tilek
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

Batch rectification on a glass bubble plate column

1. Theoretical background
There are several reasons to perform batch rectification instead of continuous rectification:

a) the mass flow of the feed is too low


b) more than two products have to be separated in one column
c) the concentration of feed is not stable
d) a good separation is necessary on acolumn with relatively small number of theoretical plates.

If batch rectification is performed, the whole amount of feed is fed into the reboiler at once, and
continuous evaporation is performed. Vapour is condensed at the top of the column int he
condenser, and a part of the condensed fluid is fed back to the column as reflux, while the other
part is collected as distillate. Liquid from the reflux and vapour are in counter-current flow int he
column, thus rectification is performed. A schematic draw of a batch rectification unit is
presented in Fig1. xj and yj are in equilibrium. The unit itself is basically a rectification column
having only upper column part.
condenser

reboiler

Fig 1. Schematic representation of a batch rectification unit

There are practically to ways to operate a batch rectification unit:

a) to work in constant reflux ratio (R) mode,


b) to work in constant distillate composition (xD) mode.

These two basic modes are presented in Fig2a and Fig 2b, respectively.
Fig 2. Two basic ways of operation a batch rectification unit

It is practical to operate in constant


onstant reflux ratio mode, if the aim is to get rid of a small amount
am of
volatile impurity. In this case, as shown in Fig2a, xD will continuously decrease
crease during the process,
as xW (molar ratio o of the volatile compound in the reboiler) is also decreasing.

If the aim of the rectification is to get the volatile compound in high purity at the top of the
column, it worths to operate it in constant xD mode (Fig2b). Inn this case, since xW is decreasing
continuously, the reflux ratio have to be continuously increased to ensure constant xD.

1.1 Batch rectification with contant reflux ratio


Mass and component balace equations if the material int he column (and the
t changing
amount of this material) is neglected:
dD=dW
WxW=(W-dW)(xW-dxW)+xDdW
where W is the amount of the material int he reboiler
D is the amount of distillate
xD is the concentration of the more volatile compound int he distillate
xW is the concentration of the more volatile compound int he reboiler.
From the equations a new is easily derived, similar to Rayleigh equation:
 
=
  − 
After integration:
  
 = =
  − 
I value of the integral may be determined by graphical or numerical methods.

It is straightforward than to calculate the amount of residue  = and distillate D=W0-W.


Avarage composition of distillate may be calculated from the overall component balance:

  − 
 =


Amount of material to be evaporised may be calculated with the reflux ratio:

V=(R+1)D

2. The measurement
The following basic knowledge is required beside the things detailed in this note: definition of
theoretical plate, phase diagram, bubble point- cloud point diagram, reflux ratio, equation of upper
working line, McCabe-Thiele method and the theoretical background required to understand and use
the above phrases.

The unit may be operated in constant reflux ratio or constant distillate concentration modes. The
unit is built up from a column with 10 bubble plates, an insulated coat with electrical heating, a1 l
inner volume reboiler, distillation head with possibility of controlling reflux ratio.

Temperatures of the reboiler and the pressure inside the reboiler have to be measured. For the
measurement of pressure drop along the column (ie. pressure in the reboiler – atmospheric
pressure) an U-tube manometer is installed. Liquid inside the U-tube is toluene.

The reboiler is heated by an oil bath, which is electrically heated. Read the temperature of the oil
bath regularly!

Temperature of vapour is to be measured in the distillation head. COntrol of reflux is perforemd by a


time-dependent electrical-magnet switch. Fractions of distillatemay be collected separately.

Electrical heating of the reboiler and that of the coat my be controlled separately. Concentrations of
distillate and residue samples are to be analysed by refractometry. A schematic draw of the
laboratory unit is shown in Fig 3.

Remember, that the used solvents are flammable!


BF coat heating
DF distillation head
E electric magnet
F reboiler heating
H thermometer
K column
M U-tube
OF oil bath
R reflux controller
SZ distillate collector

Fig 3. The laboratory batch rectification column

2.1 Starting the measurement


1. 450-500 g n-heptane- toluene mixture (heptane content between 40-55 %) is filled into the
reboiler. Phase diagrams of the mixture are shown on Fig 5 and Fig 6. Refractive index data are
collected in Fig 7.

2. Start the cooling

3. Start the heating at about 80 scales.

4. Close the valve of distillate collection.


5. When boiling starts and the bubbleplates are already working, set the heating of coat between 10-
10
30 scales. Take care, that the temperature of the coat
c should be always around 90-95°C.
90

6. Set the temperature of oil bath between 130-150


130 °C, and work in full reflux for a few minutes to
determine number of theoretical plates as follows.

6a. Open the distillate collector valve to collect previously


prev ously condensed sample. Fill it to the regdo
vessel.

6b. Switch on the reflux controller for a short period of time to wash through all pipes and collect a
few drops of sample. This should be done fast to ensure that the composition of the sample is the
same as in equilibrium during full reflux mode.

6c. Read the temperature of reboiler, pressure


p essure drop of column. Calculate the concentration of the
liquid based on the diagram in Fig 4.,., but do not forget to take into account the difference of
pressures.

 .#$%
 =   0.046 760 − !"
" − ∆)* +, !°/+
&'.$

Fig 4. Bubble point – cloud point diagram of n-heptane


n - toluene

2.2 Measurements at constant reflux ratio


12 314
2 according to the instructions. 0 =
1. Set the reflux ratio to 0.5-2 , where T2 is the total time (s)
14
and T1 is the distillate collection time. T1 is suggested to be set as 3-4 s.

2. Open the valve at the distillate collection pipe and start the timer.

3. Collect the samples for 30-30


30 s into clean vessels at the given period of the run and measure the
refractive index of samples. Read in the 15th second the temperature of reboiler and all other data
required in the report.

4. Stop the timer after taking the last sample and write down the duration of rectification.
5. Unify all distillate samples and measure avarage concentration.

Fig 5. y-x diagram of n-heptane – toluene


Fig 6. Refractive index – composition calibration diagram
Lab Report

R=constant

Starting mixture:
%
refractive index:  =

concentration: xW0= %

Atmospheric pressure: (torr)

Reflux ratio: T1= s

T2= s

R=

Heating: reboiler: coat:

Duration of rectification: (min)

time  


 567 85  xW ∆) %
 xD
(min) °C °C °C °C °C % mm %
430-500
930-1000
1930-2000
2930-3000
3930-4000
4930-5000
5930-6000
At full reflux:  = °C

 = °C
%
distillate:  = xD =

Number of theoretical plates: Ntheo


:;<=>
Avarage efficiency of plates: 9 =
:

Amount of distillate: g
%
Avarage concentration of distillate:  =  = %

Written by: Edit Székely based on the work of Radnai Gy., Láng P., Manczinger J., Lelkes Z.,
Sawinsky J.

You might also like