8/4/22, 12:24 PM Document - HPE SimpliVity 380 Gen9 Node - Configure the iLO Port for Remote Management

ure the iLO Port for Remote Management | HPE Support

2
Support Center  
H
English
o
 M m 
aS
HPE SimpliVity
en 380 Gen9 Node - Configure the iLO Port
 Remote e
for ar  Management
P
g
Configurevr the iLO port to access the iLO remote console Recently
Connect eiD to iLO  and launch the integrated remote console(IRC) Viewed
o
Link to codlist of available documents HPE Proliant
 ew u  Gen9 Servers -
Configure K
sn the iLO port to access the iLO remote console Windows 2008
Procedure cn overview R2 Installation
Fails with
 lto  Message
NOTE: R
oswPrefer to configure iLO at a later time,skip this task and deploy the server using "Windows Could
DeploymentManager.
ea not prepare the
Configure ls the iLO port to access the iLO console through a web browser. The iLO console provides out- computer to boot
ofbandremote
d
eo server management and access to advanced management options. The configuration steps into the next
mayinclude Ssd configuring IPv4, modifying the default static IP address, enabling DHCP, or changing the phase of
 u
default
u 
username and password. installation"
The server g
rp is pre-configured with a default, static IP address to access iLO (192.168.0.120). The HPE ProLiant
DL380 Gen9
iLOdefault ec user name and password are found on the label attached to the top of the chassis. The user Server - LED
 pisAdministrator
name  and the password is an eight-character alphanumeric string.
Procedure
e
o
Indicators

1. Connect sr an Ethernet cable from the Ethernet port on the laptop to the iLO Ethernet port on the rear
of theserver.
t Related
Products
Was this information helpful? Feedback HPE SimpliVity
380 Gen9
https://support.hpe.com/hpesc/public/docDisplay?docId=a00039812en_us&docLocale=en_US 1/3
8/4/22, 12:24 PM Document - HPE SimpliVity 380 Gen9 Node - Configure the iLO Port for Remote Management | HPE Support

2. If necessary, change the IPv4 address of the Ethernet port on your Windows laptop:
a. Open Network and Sharing Center in the Control Panel and click Change adapter settings.

b. Locate the icon for the Ethernet adapter, right-click it, and then select Properties. This is
typically a LocalArea Connection.
c. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.
d. Record the current settings on the General tab so that it can be restored later.
e. Check the button labeled Use the following IP address.
f. Enter an IP address in the range 192.168.0.[0-255], excluding 192.168.0.120.
g. Enter a subnet mask of 255.255.0.0.
h. Close the dialogs and exit from Network and Sharing Center.
3. Enter the default iLO IP address to access the server:
http://192.168.0.120
4. Use the default user name and password found on the label attached to the top of the chassis to log
in.
5. If prompted to do so, change the default iLO password according to your site-specific security
requirements.
6. Select Network > iLO Dedicated Network Port or Network > Shared Network Port.
7. Select the IPv4 tab.
8. On the IPv4 tab, enable DHCP or specify a static IP address, subnet mask, default gateway, and so
onbased on your network environment.
9. Click Submit to save the network settings.
10. Connect the iLO port to a switch in the rack.
top

Connect to iLO and launch the integrated remote console(IRC)

Procedure
1. Log in to any computer that can access the IP address for the iLO web interface.
2. Enter the iLO IP address into your browser.
For example: http://192.168.0.120
3. If you haven't changed the default settings, use the default user name and password found on the
labelattached to the top of the chassis to log in. If the default settings are changed, use the user
name andpassword you configured.
Was this information helpful? Feedback
4. Select Remote Console > Remote Console.
https://support.hpe.com/hpesc/public/docDisplay?docId=a00039812en_us&docLocale=en_US 2/3
8/4/22, 12:24 PM Document - HPE SimpliVity 380 Gen9 Node - Configure the iLO Port for Remote Management | HPE Support

5. Click the appropriate launch link for your system.

top

Link to list of available documents

Click here to view the list of available documents for product HPE SimpliVity 380 Gen9 Node .
top

©Copyright 2022 Hewlett Packard Enterprise Development LP

Hewlett Packard Enterprise Development shall not be liable for technical or editorial errors or omissions
contained herein. The information provided is provided "as is" without warranty of any kind. To the extent
permitted by law, neither HPE nor its affiliates, subcontractors or suppliers will be liable for incidental, special
or consequential damages including downtime cost; lost profits; damages relating to the procurement of
substitute products or services; or damages for loss of data, or software restoration. The information in this
document is subject to change without notice. Hewlett Packard Enterprise Development and the names of
Hewlett Packard Enterprise Development products referenced herein are trademarks of Hewlett Packard
Enterprise Development in the United States and other countries. Other product and company names
mentioned herein may be trademarks of their respective owners.

Legal Disclaimer: Products sold prior to the November 1, 2015 separation of Hewlett-Packard Company into Hewlett Packard Enterprise Company and HP Inc. may have older product names and model numbers that differ from current models.
Hewlett Packard Enterprise believes in being unconditionally inclusive. Efforts to replace noninclusive terms in our active products are ongoing.

© Copyright 2022 Hewlett Packard Enterprise Development

Privacy Terms of Use Ad Choices & Cookies Do Not Sell My Personal Information
LP

Was this information helpful? Feedback

https://support.hpe.com/hpesc/public/docDisplay?docId=a00039812en_us&docLocale=en_US 3/3