Multilac Acrylic Wall Filler Exterior &

Interior

USAGE Multilac Acrylic wall filler Exterior & Interior can be applied on interior and exterior walls
as a primer coat. Also suitable for plaster, concrete, building board, plywood surfaces
etc.

FEATURES Gives excellent finish, making uneven surfaces even and smooth. It improves the
adhesion to the surfaces and protects the finish coat especially in lime plastered walls.
One coat of Multilac Acrylic wall filler Exterior & Interior will reduce the quantity of the
paint required to finish the wall thus making the paint job very cost effective specially
when changing in to a new color.

PACK SIZE 1L,4L,10L and 20L

COLOUR RANGE White

TYPE OF FINISHING Matt

FILM PROPERTIES White, low sheen & filling coat

COMPOSITION Binder: Acrylic Emulsion

Solvent: Water

GLOSS LEVEL Matt

VOLUME SOLIDS
65% by weight
Approx.60-65%
( theoretical )

VOC CONTENT < 30 g/Litre

POT LIFE Not applicable

SHELF LIFE Not applicable

CURING TIMES Not applicable

TOUCH DRY 20 minutes

RECOAT/ DRY 2-3 hours

FULL CURE 24 hours

FILM THICKNESS DRY Depending on the surface

FILM THICKNESS WET Depending on the surface

THEORETICAL 14-16 Sq.m/Litre (depending on the surface)

COVERAGE

APPLICATION METHOD Brush or roller

SERVICE 10°C - 50°C

TEMPERATURE

MIXING RATIO Not applicable

INDUCTION Not applicable

THINNING Brush/Roller Application

For normal use thinning should not exceed 1 part of clean water to 1 part of
paint.

SPRAY Not applicable

RECOMMENDATION

CLEANING UP Brush and other tools must be cleaned with soap water immediately.

SURFACE Cleaning :
PREPARATION Use a stiff scraper or high pressure water jetting thoroughly to remove any
loose or flaking material, mould or algae under strict supervision.
Mould & Algae :
To kill any residual growth, the affected areas should then be treated with Multilac
Disinfecting Wall Wash. Apply 1 coat with proper PPE (Personnel Protective equipment)
for safety measures. Apply using a worn brush and leave for 24 - 48 hours, then wash,
and scrub the surface with clean high pressure water jet to remove bleach residuals and
dead growth. In severe cases, it may be necessary to repeat the treatment.
Removal of loosely bound materials :
Plastered surface need to be clean and dry. Use high pressure water jetting to remove
all loose paint and scale in order to build good adhesion properties.
Stains and leakages :
Repair this source of any leaks and drips, which cause stains. Allow the wall to dry out.
If the stain reappears, use 2 coats of Multilac Supreme Life Water Proofing Sealer
 (Solvent based) to seal the surface through and leave it to dry for 24-48 hours

DIRECTIONS FOR USE Apply 2coats of paints for best results.

Stir thoroughly before use. Do not over thin

FLASH POINT Not applicable

FREIGHT Paints (Water based)

CLASSIFICATION

MSDS REFERENCE NO.

SAFETY, HEALTH AND * Keep container tightly closed and keep out of reach of children.
ENVIRONMENTAL * When applying paint it is advisable to wear suitable eye protection.
INFORMATION * In case of contact with eyes, rinse immediately with plenty of water and seek medical
advice.
* Remove splashes from skin: use soap and water or a recognized skin cleaner.
* Ensure good ventilation during application and drying.
* Do not breathe vapour/spray.
* In case of insufficient ventilation during spraying wear suitable respiratory equipment
that meets an appropriate standard approved by the HSE.
* Care must be taken when transporting paint. Keep container in a secure upright
position, do not use or store by hanging on a hook.
* Contains no added lead.
* Protect from frost and extremes of temperature. Do not empty into drains or
watercourses.

For further information or if you have any concerns about using this product contact the Sales Department at the address below:

Macksons Paints Lanka (Pvt) Ltd.

75/1, Wattalpola Road, Henamulla,
Panadura
Tel/Fax : +94 (011) 5556559
E-mail: [email protected]

Any advice, recommendations, information, assistance or service provided by Macksons Paints Lanka (Pvt) Ltd. in relation to goods manufactured,
marketed is given in good faith. However, any advice, recommendations, information, assistance or service provided by Macksons Paints Lanka (Pvt.) Ltd
is provided without expressed or implied warranties.

th
11 July 2012