2020.

1:
* Version 13.2 (Rev. 5)
* No changes

2019.2.2:
* Version 13.2 (Rev. 5)
* No changes

2019.2.1:
* Version 13.2 (Rev. 5)
* No changes

2019.2:
* Version 13.2 (Rev. 5)
* General: IP Waivers update in constraint files. No functional changes
* Revision change in one or more subcores

2019.1.3:
* Version 13.2 (Rev. 4)
* No changes

2019.1.2:
* Version 13.2 (Rev. 4)
* No changes

2019.1.1:
* Version 13.2 (Rev. 4)
* No changes

2019.1:
* Version 13.2 (Rev. 4)
* Bug Fix: Destination Clock not connected properly for some XPM_CDC instances
when in common clock mode. Conditions added to connect the correct clock
* Other: IP Waivers added in constraint files. No functional changes
* Revision change in one or more subcores

2018.3.1:
* Version 13.2 (Rev. 3)
* No changes

2018.3:
* Version 13.2 (Rev. 3)
* Feature Enhancement: None
* Other: Reduced simulation warnings in Behavioral model. No functional changes
* Revision change in one or more subcores

2018.2:
* Version 13.2 (Rev. 2)
* No changes

2018.1:
* Version 13.2 (Rev. 2)
* Bug Fix: Enable Safety Circuit option was unintentionally made available for
user selection when Enable Reset Synchronization is not selected. This
unintentional enablement is corrected and Enable Safety Circuit is available for
user selection only if Enable Reset Synchronization option is selected
* Bug Fix: REQP-1839 DRC warning removed from example test bench
* Bug Fix: Read Data Count in behavioral model is updated to start with a valid
value when Enable Reset Synchronization option is not selected
 * Other: As FIFO Generator core uses XPM_CDC module, user must ensure that the
wr_rst and rd_rst overlap for at least C_SYNCHRONIZER_STAGE+1 slowest clock cycles
if Enable Reset Synchronization option is disabled

2017.4:
* Version 13.2 (Rev. 1)
* Revision change in one or more subcores

2017.3:
* Version 13.2
* Feature Enhancement: Enable Safety Circuit option is made default for BRAM based
FIFOs when Asynchronous Reset is selected
* Feature Enhancement: All outputs are made synchronous to respective clock domain
when Enable Safety Circuit option is selected
* Feature Enhancement: All outputs are invalid for reset duration + 60 slowest
clock cycles when Enable Safety Circuit option is selected
* Feature Enhancement: All outputs are invalid for reset duration + 30 slowest
clock cycles when Enable Safety Circuit option is not selected
* Feature Enhancement: The outputs of FIFO Generator may be Xs for initial few
clock cycles if the core is configured without reset. It is recommended to wait for
15 slowest clock cycles at the beginning of behavioral simulation (from time 0)
before accessing the FIFO

2017.2:
* Version 13.1 (Rev. 4)
* No changes

2017.1:
* Version 13.1 (Rev. 4)
* Bug Fix: FIFO Generator core was constructing the buit-in FIFO sub-optimally for
2K-deep and 36-bit wide configuration. This is corrected to use the optimal FIFO
structure
* Bug Fix: In order to enable the tool to perform the recovery check on the reset,
set_false_path for reset is kept only from the input port to the first flop where
it connects to
* Feature Enhancement: Updated the FIFO Generator's constraints to improve tool
performance processing its XDC
* Other: Internal device family change, no functional changes
* Revision change in one or more subcores

2016.4:
* Version 13.1 (Rev. 3)
* Port Change: None
* Bug Fix: Supported features table in the first page of GUI updated to reflect
the asymmetry support for common clock BRAM FIFO
* Feature Enhancement: None
* Revision change in one or more subcores

2016.3:
* Version 13.1 (Rev. 2)
* Port Change: wr_rst_busy and rd_rst_busy ports made available if safety circuit
is enabled
* Bug Fix: Fixed issue which was causing the m_axis_tvalid to go high after the
reset is released and no valid data written to the FIFO
* Feature Enhancement: Safety circuit is made independent of Output Register and
Enable Reset Synchronization options
* Other: Added support for future devices
* Other: Source HDL files are concatenated into a single file to speed up
synthesis and simulation. No changes required by the user
 * Revision change in one or more subcores

2016.2:
* Version 13.1 (Rev. 1)
* Revision change in one or more subcores

2016.1:
* Version 13.1
* Delivering only Verilog behavioral model.
* Constraint(s) for Independent Clocks Distributed RAM FIFO is changed, which may
issue a CDC-1 warning that can be safely ignored.
* Output Register option is updated to offer either Embedded Register or Fabric
Register or Both Embedded and Fabric Registers.
* Updated the FIFO Generator GUI to provide Embedded Register option for Built-in
FIFO when ECC mode in selected.
* Programmable Full and Programmable Empty Threshold range has been reduced for
UltraScale and UltraScale+ Built-in FIFO configurations. For more information on
the exact threshold range change, refer the PG(057)
* Programmable Full and Programmable Empty Threshold values were reset to its
default values when the previous version of the core is upgraded to the latest
version. This has been corrected
* Revision change in one or more subcores

2015.4.2:
* Version 13.0 (Rev. 1)
* No changes

2015.4.1:
* Version 13.0 (Rev. 1)
* No changes

2015.4:
* Version 13.0 (Rev. 1)
* Fixed safety circuit related warnings in Behavioral model
* Revision change in one or more subcores

2015.3:
* Version 13.0
* Additional safety circuit option provided for asynchronous reset configurations.
* Delivering only VHDL behavioral model.
* Added asymmetric port width support for 7-series Common Clock Block RAM FIFO
* IP revision number added to HDL module, library, and include file names, to
support designs with both locked and upgraded IP instances

2015.2.1:
* Version 12.0 (Rev. 4)
* No changes

2015.2:
* Version 12.0 (Rev. 4)
* No changes

2015.1:
* Version 12.0 (Rev. 4)
* Delivering non encrypted behavioral models.
* Enabled out-of-context clock frequency setting by adding FREQ_HZ parameter to
clock ports
* Enabling behavioral simulation for Built-in FIFO configurations changes the
simulation file names and delivery structure.
 * Supported devices and production status are now determined automatically, to
simplify support for future devices

2014.4.1:
* Version 12.0 (Rev. 3)
* No changes

2014.4:
* Version 12.0 (Rev. 3)
* Reduced DRC warnings.
* Internal device family change, no functional changes
* Encrypted source files are concatenated together to reduce the number of files
and to reduce simulator compile time

2014.3:
* Version 12.0 (Rev. 2)
* Added support for Asynchronous AXI Stream Packet FIFO for UltraScale devices.
* Added support for write data count and read data count for Asynchronous AXI
Stream Packet FIFO for UltraScale devices.
* Added support for write data count and read data count for Common Clock Block
RAM FIFO when Asymmetric Port Width option is enabled for UltraScale devices.
* Added support for Low Latency Built-in FIFO for UltraScale devices.

2014.2:
* Version 12.0 (Rev. 1)
* Repackaged to improve internal automation, no functional changes.

2014.1:
* Version 12.0
* Asynchronous reset port (rst) for Built-in FIFO configurations is removed for
UltraScale Built-in FIFO configurations. When upgrading from previously released
core, 'rst' port will be replaced by 'srst' port.
* Synchronous reset (srst) mechanism is changed now for UltraScale devices. FIFO
Generator will now provide wr_rst_busy and rd_rst_busy output ports. When
wr_rst_busy is active low, the core is ready for write operation and when
rd_rst_busy is active low, the core is ready for read operation.
* Added asymmetric port width support for Common Clock Block RAM FIFO, Common
Clock Built-in FIFO and Independent Clocks Built-in FIFO configurations for
UltraScale Devices
* Added 'sleep' input port for Common Clock Built-in FIFO and Independent Clocks
Built-in FIFO configurations only for UltraScale Devices
* Internal device family name change, no functional changes

2013.4:
* Version 11.0 (Rev. 1)
* Added support for Ultrascale devices
* Common Clock Builtin FIFO is set as default implementation type only for
UltraScale devices
* Embedded Register option is always ON for Block RAM and Builtin FIFOs only for
UltraScale devices
* Reset is sampled with respect to wr_clk/clk and then synchronized before the use
in FIFO Generator only for UltraScale devices

2013.3:
* Version 11.0
* AXI ID Tags (s_axi_wid and m_axi_wid) are now determined by AXI protocol type
(AXI4, AXI3). When upgrading from previously released core, these signals will be
removed when AXI_Type = AXI4_Full.
* AXI Lock signals (s_axi_awlock, m_axi_awlock, s_axi_arlock and m_axi_arlock) are
now determined by AXI Protocol type (AXI4, AXI3). When upgrading from previously
released core, these signals width will reduce from 2-bits to 1-bit when
AXI_Type=AXI4_Full
* Removed restriction on packet size in AXI4 Stream FIFO mode. Now, the packet
size can be up to FIFO depth
* Enhanced support for IP Integrator
* Reduced warnings in synthesis and simulation
* Added support for Cadence IES and Synopsys VCS simulators
* Improved GUI speed and responsiveness, no functional changes
* Increased the maximum number of synchronization stages from 4 to 8. The minimum
FIFO depth is limited to 32 when number of synchronization stages is > 4

2013.2:
* Version 10.0 (Rev. 1)
* Constraints processing order changed

2013.1:
* Version 10.0
* Native Vivado Release
* There have been no functional or interface changes to this IP. The version
number has changed to support unique versioning in Vivado starting with 2013.1.

(c) Copyright 2002 - 2020 Xilinx, Inc. All rights reserved.

This file contains confidential and proprietary information

of Xilinx, Inc. and is protected under U.S. and
international copyright and other intellectual property
laws.

DISCLAIMER
This disclaimer is not a license and does not grant any
rights to the materials distributed herewith. Except as
otherwise provided in a valid license issued to you by
Xilinx, and to the maximum extent permitted by applicable
law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
(2) Xilinx shall not be liable (whether in contract or tort,
including negligence, or under any other theory of
liability) for any loss or damage of any kind or nature
related to, arising under or in connection with these
materials, including for any direct, or any indirect,
special, incidental, or consequential loss or damage
(including loss of data, profits, goodwill, or any type of
loss or damage suffered as a result of any action brought
by a third party) even if such damage or loss was
reasonably foreseeable or Xilinx had been advised of the
possibility of the same.

CRITICAL APPLICATIONS
Xilinx products are not designed or intended to be fail-
safe, or for use in any application requiring fail-safe
performance, such as life-support or safety devices or
systems, Class III medical devices, nuclear facilities,
applications related to the deployment of airbags, or any
other applications that could lead to death, personal
injury, or severe property or environmental damage
(individually and collectively, "Critical
Applications"). Customer assumes the sole risk and
liability of any use of Xilinx products in Critical
Applications, subject only to applicable laws and
regulations governing limitations on product liability.

THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS

PART OF THIS FILE AT ALL TIMES.