DRIVER CONTROLS

SECTION DEF DEFOGGER

B

E
CONTENTS
BASIC INSPECTION .................................... 3 Component Inspection .............................................17 F

DIAGNOSIS AND REPAIR WORKFLOW .......... 3 DOOR MIRROR DEFOGGER ........................... 18

Work Flow ................................................................. 3 G
DRIVER SIDE .............................................................18
FUNCTION DIAGNOSIS ............................... 4 DRIVER SIDE : Description .....................................18
DRIVER SIDE : Component Function Check ..........18
REAR WINDOW DEFOGGER SYSTEM ............. 4 DRIVER SIDE : Diagnosis Procedure .....................18 H
System Diagram ........................................................ 4 DRIVER SIDE : Component Inspection ...................19
System Description ................................................... 4
PASSENGER SIDE ....................................................19
Component Parts Location ........................................ 5 I
PASSENGER SIDE : Description ............................19
Component Description ............................................. 5
PASSENGER SIDE : Component Function Check
DIAGNOSIS SYSTEM (BCM) ............................. 6 ....19
PASSENGER SIDE : Diagnosis Procedure ............20 J
COMMON ITEM ........................................................... 6 PASSENGER SIDE : Component Inspection ..........21
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ....................................................... 6 REAR WINDOW DEFOGGER ON SIGNAL ..... 22
Description ...............................................................22 K
REAR WINDOW DEFOGGER ..................................... 6 Component Function Check ....................................22
REAR WINDOW DEFOGGER : CONSULT-III Diagnosis Procedure ...............................................22
Function (BCM - REAR DEFOGGER) ...................... 6 DEF
ECU DIAGNOSIS ......................................... 23
DIAGNOSIS SYSTEM (IPDM E/R) ...................... 8
Diagnosis Description ............................................... 8 BCM (BODY CONTROL MODULE) ................. 23
CONSULT-III Function (IPDM E/R) ......................... 10 Reference Value ......................................................23 M
Wiring Diagram - DEFOGGER CONTROL SYS-
COMPONENT DIAGNOSIS ......................... 13 TEM (LHD MODELS) - ............................................40
Wiring Diagram - DEFOGGER CONTROL SYS- N
REAR WINDOW DEFOGGER SWITCH ............13
TEM (RHD MODELS) - ...........................................45
Description .............................................................. 13
Fail Safe ..................................................................49
Component Function Check .................................... 13
DTC Inspection Priority Chart ...............................50 O
Diagnosis Procedure ............................................... 13
DTC Index ...............................................................51
REAR WINDOW DEFOGGER RELAY ..............15
IPDM E/R (INTELLIGENT POWER DISTRI-
Description .............................................................. 15 P
Component Function Check .................................... 15
BUTION MODULE ENGINE ROOM) ................ 52
Reference Value ......................................................52
Diagnosis Procedure ............................................... 15
Wiring Diagram - DEFOGGER CONTROL SYS-
REAR WINDOW DEFOGGER ...........................16 TEM (LHD MODELS) - ............................................57
Description .............................................................. 16 Wiring Diagram - DEFOGGER CONTROL SYS-
Component Function Check .................................... 16 TEM (RHD MODELS) - ...........................................62
Diagnosis Procedure ............................................... 16 Fail Safe ..................................................................66

DEF-1 GETtheMANUALS.org
 DTC Index .............................................................. 68 PASSENGER SIDE ................................................... 71
PASSENGER SIDE : Diagnosis Procedure ............ 71
SYMPTOM DIAGNOSIS ............................. 69
REAR WINDOW DEFOGGER SWITCH DOES
REAR WINDOW DEFOGGER AND DOOR NOT LIGHT, BUT REAR WINDOW DEFOG-
MIRROR DEFOGGER DO NOT OPERATE. ..... 69 GER OPERATES ............................................... 72
Diagnosis Procedure .............................................. 69 Diagnosis Procedure ............................................... 72
REAR WINDOW DEFOGGER DOES NOT PRECAUTION ............................................ 73
OPERATE BUT BOTH OF DOOR MIRROR
DEFOGGER OPERATE. ................................... 70 PRECAUTIONS ................................................. 73
Diagnosis Procedure .............................................. 70 Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
DOOR MIRROR DEFOGGER DOES NOT OP- SIONER" ................................................................. 73
ERATE ............................................................... 71
ON-VEHICLE REPAIR ............................... 74
BOTH SIDE ............................................................... 71
BOTH SIDE : Diagnosis Procedure ........................ 71 FILAMENT ......................................................... 74
Inspection and Repair ............................................. 74
DRIVER SIDE ............................................................ 71
DRIVER SIDE : Diagnosis Procedure .................... 71

DEF-2 GETtheMANUALS.org
 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000001279544
B

DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM C
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
D
>> GO TO 2.
2.CHECK DTC E
Perform self diagnosis with CONSULT-III
Is any DTC detected?
YES >> Refer to BCS-65, "DTC Index". F
NO >> GO TO 3.
3.REPRODUCE THE MALFUNCTION INFORMATION G
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
H
>> GO TO 4.
4.IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
I
Use “Symptom diagnosis” from the symptom inspection result in step 3. Then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.

J
>> GO TO 5.
5.IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system. K

>> GO TO 6.
DEF
6.REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
M
>> GO TO 7.
7.FINAL CHECK
N
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 3.
IAre all malfunctions corrected?
O
YES >> INSPECTION END.
NO >> GO TO4.
P

DEF-3 GETtheMANUALS.org
 REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS
REAR WINDOW DEFOGGER SYSTEM
System Diagram INFOID:0000000001279545

JMLIA0049GB

System Description INFOID:0000000001279546

OPERATION DESCRIPTION
• BCM detects that the rear window defogger switch is turned ON when the ignition switch is ON, and then
transmits the rear window defogger switch signal to IPDM E/R via CAN communication for approximately 15
minutes.
• IPDM E/R turns rear window defogger relay ON when it receives the rear window defogger switch signal.
Then, it transmits the rear window defogger ON signal to ECM via CAN communication.
• The power is supplied to the rear window defogger and door mirror defogger (with mirror defogger) when the
rear window defogger relay is turned ON.

TIMER FUNCTION
• BCM transmits the rear window defogger switch signal to IPDM E/R for approximately 15 minutes when the
rear window defogger switch is turned ON with the ignition switch ON. Then, IPDM E/R operates the rear
window defogger and door mirror defogger (with mirror defogger).
• The timer is cancelled if the rear window defogger switch is pressed again during timer operation. BCM
stops the output of rear window defogger switch signal. The same reaction also occurs during timer opera-
tion if the ignition switch is turned OFF.
INPUT/OUTPUT SIGNAL CHART

Switch Input signal to BCM BCM function Acutuator

Rear window defogger switch Defogger switch signal Rear window defogger & Door mir- Rear window defogger
Ignition switch Ignition switch ON signal ror defogger control Door mirror defogger

DEF-4 GETtheMANUALS.org
 REAR WINDOW DEFOGGER SYSTEM
< FUNCTION DIAGNOSIS >
Component Parts Location INFOID:0000000001279547

JMLIA0048ZZ

I
Rear window defogger switch (built
in AUTO AMP.)
1. BCM M65,M66,M67 2. IPDM E/R E11, E13 3.
Gasoline engine models: M50, M51
Diesel engine models: M53 J
4. Rear window defogger D184 5. Rear window defogger D185
A. Behind glove box B. Engine room dash panel (LH) C. Behind back door trim finisher
K
Component Description INFOID:0000000001279548

DEF
• Rear window defogger switch operation is transmitted to IPDM E/R via CAN commu-
BCM nication.
• Performs the timer control of rear window defogger.
M
Rear window defogger relay • Operates the rear window defogger and the door mirror defogger with the control sig-
nal from IPDM E/R.
• BCM controls rear window defogger relay via CAN communication, and then oper-
IPDM E/R N
ates rear window defogger or door mirror defogger.
Auto amp. • The rear window defogger switch is installed.
(Rear window defogger switch) • Turns the indicator lamp ON when detecting the operation of rear window defogger.
• Heats the heating wire with the power supply from the rear window defogger relay to O
Rear window defogger
prevent the rear window from fogging up.
• Heats the heating wire with the power supply from the rear window defogger relay to
Door mirror defogger
prevent the door mirror from fogging up. P

DEF-5 GETtheMANUALS.org
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000001366485

APPLICATION ITEM
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.

Diagnosis mode Function description

ECU Identification BCM part number is displayed.
Self-Diagnostic Results Displays the diagnosis results judged by BCM. Refer to BCS-65, "DTC Index".
Data Monitor BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Work Support Changes the setting for each system function.
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.

SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item

CONSULT-III Diagnosis mode

System
sub system selection item WORK SUPPORT DATA MONITOR ACTIVE TEST
— BCM ×
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × ×
Warning chime BUZZER × ×
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Air conditioner AIR CONDITONER ×
Intelligent Key system INTELLIGENT KEY ×
Combination switch COMB SW ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Back door open TRUNK × ×
Vehicle security system THEFT ALM × × ×
Signal buffer system SIGNAL BUFFER × ×
— PTC HEATER*
*: This item is displayed, but is not function.
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)
INFOID:0000000001279550

Data monitor
DEF-6 GETtheMANUALS.org
 DIAGNOSIS SYSTEM (BCM)
< FUNCTION DIAGNOSIS >

Monitor Item Description A

REAR DEF SW Displays “Press (ON)/other (OFF)” status determined with the rear window defogger switch.
IGN ON SW Indicates [ON/OFF] condition of ignition switch in ON position.
ACC ON SW Indicates [ON/OFF] condition of ignition switch in ACC position.
B

ACTIVE TEST
C
Test Item Description
REAR DEFOGGER Give a drive signal to the rear window defogger relay to activate it.
D

DEF

DEF-7 GETtheMANUALS.org
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description INFOID:0000000001366483

Auto active test

Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Rear window defogger
• Front wiper (LO, HI)
• Parking lamps
• License plate lamps
• Tail lamps
• Front fog lamps
• Headlamps (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan (LO, MID, HI)
Operation procedure
1. Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2. Turn ignition switch OFF.
3. Turn the ignition switch ON, and within 20 seconds, press the driver door switch 20 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4. Turn the ignition switch ON within 10 seconds. Then the horn sounds once and the auto active test starts.
NOTE:
Only a vehicle with the vehicle security system, the horn sounds.
5. The oil pressure warning lamp starts blinking when the auto active test starts.
6. After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
When auto active test mode has to be cancelled halfway through test, turn ignition switch OFF.
CAUTION:
• If auto active test mode cannot be actuated, check door switch system.
• Never start the engine.
Inspection in auto active test mode
When auto active test mode is actuated, the following 6 steps are repeated 3 times.

JPMIA0313ZZ

DEF-8 GETtheMANUALS.org
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >

Operation A
Inspection location Operation
sequence
A Oil pressure warning lamp Blinks continuously during operation of auto active test.
1 Rear window defogger 10 seconds B
2 Front wiper LO for 5 seconds → HI for 5 seconds
• Parking lamps
• License plate lamps C
3 10 seconds
• Tail lamps
• Front fog lamps
4 Headlamps LO ⇔ HI 5 times D
5 A/C compressor (magnet clutch) ON ⇔ OFF 5 times
6 Cooling fan LO for 5 seconds → MID for 3 seconds → HI for 2 seconds
E
Concept of auto active test

JPMIA0310GB

• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto K
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode DEF

Symptom Inspection contents Possible cause

M
YES BCM signal input circuit

Perform auto active test. • Rear window defogger

Rear window defogger does not operate Does the rear window defog- • Rear window defogger ground circuit
ger operate? NO • Harness or connector between IPDM N
E/R and rear window defogger
• IPDM E/R
Any of the following components do not operate YES BCM signal input circuit O
• Parking lamps
• License plate lamps Perform auto active test. • Lamp or motor
• Tail lamps Does the applicable system • Lamp or motor ground circuit
• Front fog lamps operate? NO • Harness or connector between IPDM P
• Headlamps (HI, LO) E/R and applicable system
• Front wiper (HI, LO) • IPDM E/R

DEF-9 GETtheMANUALS.org
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >
Symptom Inspection contents Possible cause
• Communication signal between BCM
and auto amp.
• BCM
YES • CAN communication signal between
Perform auto active test. BCM and ECM
A/C compressor does not operate Does the magnet clutch oper- • CAN communication signal between
ate? ECM and IPDM E/R
• Magnet clutch
• Harness or connector between IPDM
NO
E/R and magnet clutch
• IPDM E/R
• Harness or connector between IPDM
E/R and oil pressure switch
YES
• Oil pressure switch
Perform auto active test. • IPDM E/R
Oil pressure warning lamp does not operate Does the oil pressure warning • CAN communication signal between
lamp blink? IPDM E/R and BCM
NO • CAN communication signal between
BCM and combination meter
• Combination meter
• ECM signal input circuit
YES • CAN communication signal between
ECM and IPDM E/R
• Cooling fan motor-2 power supply cir-
cuit
• Cooling fan motor-1 ground circuit
• Cooling fan relay-4 or cooling fan re-
lay-5 power supply circuit
• Cooling fan relay-5 ground circuit
Perform auto active test. • Harness or connector between IPDM
Cooling fan does not operate E/R and cooling fan motor
Does the cooling fan operate?
• Harness or connector between IPDM
NO
E/R, and cooling fan relay-4 or cooling
fan relay-5
• Harness or connector between cooling
fan motor-2, and cooling fan relay-4 or
cooling fan relay-5
• Cooling fan relay-4 or cooling fan re-
lay-5
• Cooling fan motor
• IPDM E/R

CONSULT-III Function (IPDM E/R) INFOID:0000000001366484

APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with IPDM E/R.

Diagnosis mode Description

Self Diagnostic Result Displays the diagnosis results judged by IPDM E/R.
Data Monitor Displays the real-time input/output data from IPDM E/R input/output data.
Active Test IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support MNTR The results of transmit/receive diagnosis of CAN communication can be read.

SELF DIAGNOSTIC
Refer to PCS-26, "DTC Index".
DATA MONITOR
Monitor item

DEF-10 GETtheMANUALS.org
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >

Monitor Item MAIN A

Description
[Unit] SIGNALS
MOTOR FAN REQ Displays the value of the cooling fan speed signal received from ECM via CAN commu-
×
[1 - 4] nication.
B
AC COMP REQ Displays the status of the A/C compressor request signal received from ECM via CAN
×
[Off/On] communication.
TAIL&CLR REQ Displays the status of the position light request signal received from BCM via CAN com- C
×
[Off/On] munication.
HL LO REQ Displays the status of the low beam request signal received from BCM via CAN commu-
×
[Off/On] nication.
D
HL HI REQ Displays the status of the high beam request signal received from BCM via CAN com-
×
[Off/On] munication.
Displays the status of the front fog light request signal received from BCM via CAN com-
E
FR FOG REQ munication.
×
[Off/On] NOTE:
This item is monitored only the vehicle with front fog lamp system.
Displays the status of the headlamp washer request signal received from BCM via CAN F
HL WASHER REQ communication.
[Off/On] NOTE:
This item is monitored only the vehicle with headlamp washer system.
G
FR WIP REQ Displays the status of the front wiper request signal received from BCM via CAN com-
×
[Stop/1LOW/Low/Hi] munication.
WIP AUTO STOP H
× Displays the status of the front wiper auto stop signal judged by IPDM E/R.
[STOP P/ACT P]
WIP PROT
× Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
[Off/BLOCK]
I
ST RLY REQ Displays the status of the ignition and starter request signal received from BCM via CAN
[Off/On] communication.
IGN RLY
× Displays the status of the ignition relay judged by IPDM E/R. J
[Off/On]
RR DEF REQ Displays the status of the rear defogger request signal received from BCM via CAN com-
×
[Off/On] munication.
K
OIL P SW
Displays the status of the oil pressure switch judged by IPDM E/R.
[Open/Close]
REV SW NOTE:
[Off/On] This item is indicated, but not monitored. DEF
Displays the status of the daytime running light request signal received from BCM via
DTRL REQ CAN communication.
[Off/On] NOTE: M
This item is monitored only the vehicle with daytime running light system.
Displays the status of the hood switch judged by IPDM E/R.
HOOD SW
NOTE: N
[Off/On]
This item is monitored only the vehicle with the vehicle security system.
Displays the status of the theft warning horn request signal received from BCM via CAN
THFT HRN REQ communication.
[Off/On] NOTE: O
This item is monitored only the vehicle with the vehicle security system.
HORN CHIRP NOTE:
[Off/On] This item is indicated, but not monitored. P

ACTIVE TEST
Test item

DEF-11 GETtheMANUALS.org
 DIAGNOSIS SYSTEM (IPDM E/R)
< FUNCTION DIAGNOSIS >

Test item Operation Description

Off OFF
REAR DEFOGGER
On Operates the rear window defogger relay.
Off OFF
FRONT WIPER Lo Operates the front wiper relay.
Hi Operates the front wiper relay and front wiper high relay.
1 OFF
2 Operates the cooling fan relay (LO operation).
MOTOR FAN
3 Operates the cooling fan relay (MID operation).
4 Operates the cooling fan relay (HI operation).
HEAD LAMP WASHER On Operates the headlamp washer relay for 1 second.
Off OFF
Operates the tail lamp relay and the daytime running light relay.
TAIL NOTE:
Daytime running light relay is with daytime running light system only.
Lo Operates the headlamp low relay.
EXTERNAL LAMPS
Operates the headlamp low relay and ON/OFF the headlamp high relay at 4 sec-
Hi
onds intervals.
Operates the front fog lamp relay.
Fog NOTE:
This item can test only the vehicle with front fog lamp system.
Operates horn relay for 20 ms.
HORN On NOTE:
This item can test only the vehicle with vehicle security system.

DEF-12 GETtheMANUALS.org
 REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS A
REAR WINDOW DEFOGGER SWITCH
Description INFOID:0000000001279553
B
The rear window defogger is operated by turning the rear window defogger switch ON.
Component Function Check INFOID:0000000001279554 C

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

Check (“REAR DEF SW”, “IGN ON SW”) in DATA MONITOR mode with CONSULT-III. Refer to DEF-6, "REAR D
WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)".

When rear defogger switch is turned to ON E

REAR DEF SW :ON
OK or NG
F
OK >> Rear window defogger switch is OK.
NG >> Refer to DEF-13, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000001279555
G

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION

1. Turn ignition switch ON. H
2. Check voltage between BCM harness connector and ground.

BCM Voltage (V)

Ground Condition I
Connector Terminal (Approx.)

Rear window defogger switch is pressing. 0

J

M65 20 Ground Rear window defogger switch is not K

pressed.

JPMIA0154GB
DEF
Is the inspection result normal?
YES >> GO TO 6.
M
NO >> GO TO 2.
2.CHECK REAR WINDOW DEFOGGER SWITCH CIRCUIT
1. Turn ignition switch OFF. N
2. Disconnect BCM connector and auto amp. connector.
3. Check continuity between BCM harness connector and auto amp. harness connector.
O
BCM Auto amp.
Continuity
Connector Terminal Connector Terminal
Gasoline engine models M51 22 P
M65 20 Yes
Diesel engine models M53 25
4. Check continuity between BCM harness connector and ground.

BCM
Ground Continuity
Connector Terminal
M65 20 Ground No

DEF-13 GETtheMANUALS.org
 REAR WINDOW DEFOGGER SWITCH
< COMPONENT DIAGNOSIS >
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and auto amp.
3.CHECK REAR WINDOW DEFOGGER SWITCH GROUND CIRCUIT
Check continuity between auto amp. harness connector and ground.

Auto amp.
Ground Continuity
Connector Terminal
Gasoline engine models M51 22
Ground Existed
Diesel engine models M53 25
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness between auto amp. and ground.
4.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
2. Turn ignition switch ON.
3. Check voltage between BCM harness connector and ground.

BCM Voltage (V)

Ground
Connector Terminal (Approx.)

M65 20 Ground

JPMIA0154GB

Is the inspection result normal?

YES >> GO TO 5.
NO >> GO TO 6.
5.CHECK IINTERMITTENT INCDENT
Refer to GI-39, "Intermittent Incident"
Is the inspection result normal?
YES >> Replace auto amp. Refer to VTL-18, "Removal and Installation"
NO >> Repair or replace the malfunctioning parts.
6.CHECK IINTERMITTENT INCDENT
Refer to GI-39, "Intermittent Incident"

>> INSPECTION END

DEF-14 GETtheMANUALS.org
 REAR WINDOW DEFOGGER RELAY
< COMPONENT DIAGNOSIS >
REAR WINDOW DEFOGGER RELAY
A
Description INFOID:0000000001366466

The rear window defogger is operated by turning the rear window defogger switch ON. B
Component Function Check INFOID:0000000001366467

1.CHECK REAR WINDOW DEFOGGER SWITCH OPERATION C

Check (“REAR DEF SW”, “IGN ON SW”) in DATA MONITOR mode with CONSULT-III. Refer to DEF-6, "REAR
WINDOW DEFOGGER : CONSULT-III Function (BCM - REAR DEFOGGER)".
D
When rear window defogger switch is turned to ON
REAR DEF SW :ON
E
OK or NG
OK >> Rear window defogger switch is OK.
NG >> Refer to DEF-15, "Diagnosis Procedure".
F
Diagnosis Procedure INFOID:0000000001366486

1.CHECK FUSE G
1. Turn ignition switch OFF.
2. Check the following.
- 15A fuse (No. 55, located in IPDM E/R) H
- 15A fuse (No. 56, located in IPDM E/R)
Is the inspection result normal?
YES >> GO TO 2. I
NO >> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.CHECK IPDM E/R OUTPUT SIGNAL
J
1. Turn ignition switch ON.
2. Check voltage between IPDM E/R harness connector and ground.

IPDM E/R K
Voltage (V)
Ground Condition of rear window defogger switch
Connector Terminal (Approx.)

ON Battery voltage
E11 12 Ground DEF
OFF 0
Is the inspection result normal?
YES >> GO TO 3. M
NO >> Replace IPDM E/R. Refer to PCS-28, "Removal and Installation".
3.CHECK INTERMITTENT INCIDENT
N
Refer toGI-39, "Intermittent Incident"

>> INSPECTION END O

DEF-15 GETtheMANUALS.org
 REAR WINDOW DEFOGGER
< COMPONENT DIAGNOSIS >
REAR WINDOW DEFOGGER
Description INFOID:0000000001279560

Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.
Component Function Check INFOID:0000000001279561

1.CHECK REAR WINDOW DEFOGGER

Check that the heating wire of rear window defogger is heated when turning the rear window defogger switch
ON.
Is the inspection result normal?
YES >> Rear window defogger is OK.
NO >> Refer to DEF-16, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000001279562

1.CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT

1. Turn ignition switch ON.
2. Check voltage between rear window defogger harness connector and ground.

Rear window defogger Condition of rear window Voltage (V)

Ground
Connector Terminal defogger switch (Approx.)

ON Battery voltage
D184 1 Ground
OFF 0
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK REAR WINDOW DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect rear window defogger connector.
3. Check continuity between rear window defogger harness connector and ground.

Rear window defogger

Ground Continuity
Connector Terminal
D185 3 Ground Existed
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between rear window defogger and ground.
3.CHECK FILAMENT
Check filament.
Refer to DEF-17, "Component Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair filament.
4.CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and rear window defogger connectors.
3. Check continuity between IPDM E/R and rear window defogger harness connector.

DEF-16 GETtheMANUALS.org
 REAR WINDOW DEFOGGER
< COMPONENT DIAGNOSIS >

IPDM E/R Rear window defogger A

Continuity
Connector Terminal Connector Terminal
E11 12 D184 1 Existed
B
4. Check continuity between IPDM E/R connector and ground.

IPDM E/R
Ground Continuity C
Connector Terminal
E11 12 Ground Not existed
Is the inspection result normal? D
YES >> GO TO 5.
NO >> Repair or replace harness between IPDM E/R and rear window defogger.
5.CHECK INTERMITTENT INCIDENT E
Refer to GI-39, "Intermittent Incident"
F
>> INSPECTION END
Component Inspection INFOID:0000000001279563

G
1.CHECK FILAMENT
Check the filament for damage or blown.
Refer to DEF-74, "Inspection and Repair". H
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Repair filament. I

DEF

DEF-17 GETtheMANUALS.org
 DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
DOOR MIRROR DEFOGGER
DRIVER SIDE
DRIVER SIDE : Description INFOID:0000000001279564

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
DRIVER SIDE : Component Function Check INFOID:0000000001279565

1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Check that heating wire of driver side door mirror defogger is heated when turning the rear window defogger
switch ON.
Is the inspection result normal?
YES >> Driver side door mirror defogger is OK.
NO >> Refer to DEF-18, "DRIVER SIDE : Diagnosis Procedure".
DRIVER SIDE : Diagnosis Procedure INFOID:0000000001279566

1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10A fuse (No. 6, located in fuse and fusible link box).
Is the inspection result normal?
YES >> Replace the blown fuse after repairing the affected circuit if fuse is blown.
NO >> GO TO 2.
2.CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between door mirror (driver side) harness connector and ground.

Door mirror (driver side) Condition of rear win- Voltage (V)

Ground
Connector Terminal dow defogger switch (Approx.)

LHD D3 2 ON Battery voltage

Ground
RHD D23 1 OFF 0
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror (driver side) connector.
3. Check continuity between door mirror (driver side) harness connector and ground.

Door mirror (driver side)

Ground Continuity
Connector Terminal
LHD D3 10
Ground Existed
RHD D23 5
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness between door mirror (driver side) and ground.
4.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER
Check driver side door mirror defogger.
Refer to DEF-19, "DRIVER SIDE : Component Inspection".
Is the inspection result normal?

DEF-18 GETtheMANUALS.org
 DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
YES >> GO TO 6.
NO >> Replace door mirror glass (driver side). Refer to MIR-25, "DOOR MIRROR ASSEMBLY : Removal A
and Installation".
5.CHECK DOOR MIRROR CIRCUIT
B
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and door mirror (driver side) connector.
3. Check continuity between door mirror (driver side) harness connector and IPDM E/R harness connector.
C
Door mirror (driver side) IPDM E/R
Continuity
Connector Terminal Connector Terminal
LHD D3 2 D
E11 12 Existed
RHD D23 1
4. Check continuity between door mirror (driver side) harness connector and ground. E

Door mirror (driver side)

Ground Continuity
Connector Terminal F
LHD D3 2
Ground Not existed
RHD D23 1
Is the inspection result normal? G
YES >> GO TO 6.
NO >> Repair or replace harness between door mirror (driver side) and IPDM E/R.
H
6.CHECK INTERMITTENT
Refer to GI-39, "Intermittent Incident"
I
>> INSPECTION END
DRIVER SIDE : Component Inspection INFOID:0000000001279567
J
1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER
1. Turn ignition switch OFF. K
2. Disconnect door mirror (driver side) connector.
3. Check continuity between door mirror terminals.

Door mirror (diver side)

DEF
Continuity
Connector Terminal
LHD D3 2 10 M
Existed
RHD D23 1 5
Is the inspection result normal?
YES >> INSPECTION END. N
NO >> Replace door mirror glass (driver side). Refer to MIR-25, "DOOR MIRROR ASSEMBLY : Removal
and Installation".
PASSENGER SIDE O

PASSENGER SIDE : Description INFOID:0000000001316059

Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror P
from fogging up.
PASSENGER SIDE : Component Function Check INFOID:0000000001316060

1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER

DEF-19 GETtheMANUALS.org
 DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >
Check that heating wire of passenger side door mirror defogger is heated when turning the rear window defog-
ger switch ON.
Is the inspection result normal?
YES >> Passenger side door mirror defogger is OK.
NO >> Refer to DEF-20, "PASSENGER SIDE : Diagnosis Procedure".
PASSENGER SIDE : Diagnosis Procedure INFOID:0000000001316260

1.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10A fuse (No. 6, located in fuse and fusible link box).
Is the inspection result normal?
YES >> Replace the blown fuse after repairing the affected circuit if fuse is blown.
NO >> GO TO 2.
2.CHECK DOOR MIRROR DEFOGGER POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between door mirror (passenger side) harness connector and ground.

Door mirror (passenger side) Condition of rear win- Voltage (V)

Ground
Connector Terminal dow defogger switch (Approx.)

LHD D43 1 ON Battery voltage

Ground
RHD D63 2 OFF 0
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 5.
3.CHECK DOOR MIRROR DEFOGGER GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect door mirror (passenger side) connector.
3. Check continuity between door mirror (passenger side) harness connector and ground.

Door mirror (passenger side)

Ground Continuity
Connector Terminal
LHD D43 5
Ground Existed
RHD D63 10
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness between door mirror (passenger side) and ground.
4.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER
Check passenger side door mirror defogger.
Refer to DEF-21, "PASSENGER SIDE : Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace door mirror glass (passenger side). Refer to MIR-25, "DOOR MIRROR ASSEMBLY :
Removal and Installation".
5.CHECK DOOR MIRROR CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and door mirror (passenger side) connector.
3. Check continuity between door mirror (passenger side) harness connector and IPDM E/R harness con-
nector.

DEF-20 GETtheMANUALS.org
 DOOR MIRROR DEFOGGER
< COMPONENT DIAGNOSIS >

Door mirror (passenger side) IPDM E/R A

Continuity
Connector Terminal Connector Terminal
LHD D43 1
E11 12 Existed B
RHD D63 2
4. Check continuity between door mirror (passenger side) harness connector and ground.
C
Door mirror (passenger side)
Ground Continuity
Connector Terminal
LHD D43 1 D
Ground Not existed
RHD D63 2
Is the inspection result normal?
YES >> GO TO 6. E
NO >> Repair or replace harness between door mirror (passenger side) and IPDM E/R.
6.CHECK INTERMITTENT F
Refer to GI-39, "Intermittent Incident"

>> INSPECTION END G

PASSENGER SIDE : Component Inspection INFOID:0000000001316062

1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER H

1. Turn ignition switch OFF.

2. Disconnect door mirror (passenger side) connector.
I
3. Check continuity between door mirror terminals connector.

Door mirror (passenger side)

Continuity J
Connector Terminal
LHD D43 1 5
Existed
RHD D63 2 10 K
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Replace door mirror glass (passenger side). Refer to MIR-25, "DOOR MIRROR ASSEMBLY : DEF
Removal and Installation".

DEF-21 GETtheMANUALS.org
 REAR WINDOW DEFOGGER ON SIGNAL
< COMPONENT DIAGNOSIS >
REAR WINDOW DEFOGGER ON SIGNAL
Description INFOID:0000000001279572

Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.
Component Function Check INFOID:0000000001279573

1.CHECK REAR WINDOW DEFOGGER ON SIGNAL

Check that the indicator lamps of rear window defogger switch are illuminated when turning the rear window
defogger switch ON.
Is the inspection result normal?
OK >> Rear window defogger ON signal is OK.
NG >> Refer to DEF-22, "Diagnosis Procedure".
Diagnosis Procedure INFOID:0000000001279574

1.CHECK REAR WINDOW DEFOGGER INDICATOR LAMPS ON SIGNAL

1. Turn ignition switch ON.
2. Check voltage between auto amp. connector ground.

Auto amp. Condition of rear win- Voltage (V)

Ground
Connector Terminal dow defogger switch (Approx.)

Gasoline engine models M51 23 ON Battery voltage

Ground
Diesel engine models M53 24 OFF 0
Is the inspection result normal?
YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK REAR WINDOW DEFOGGER INDICATOR LAMPS CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R and auto amp. connector.
3. Check continuity between IPDM E/R connector and auto amp. connector.

IPDM E/R Auto amp.

Continuity
Connector Terminal Connector Terminal
M51 (Gasoline engine models) 23
E11 12 Existed
M53 (Diesel engine models) 24
4. Check continuity between IPDM E/R connector and ground.

IPDM E/R
Ground Continuity
Connector Terminal
E11 12 Ground Not existed
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between IPDM E/R and auto amp.
3.CHECK IINTERMITTENT INCDENT
Refer to GI-39, "Intermittent Incident".

>> INSOECTION END

DEF-22 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
ECU DIAGNOSIS A
BCM (BODY CONTROL MODULE)
Reference Value INFOID:0000000001551373
B

VALUES ON THE DIAGNOSIS TOOL

C
Monitor Item Condition Value/Status
VEHICLE SPEED While driving Equivalent to speedometer reading
Ignition switch OFF or ACC Off D
IGN ON SW
Ignition switch ON On
Mechanical key is removed from key cylinder Off
KEY ON SW E
Mechanical key is inserted to key cylinder On
Door lock/unlock switch does not operate Off
CDL LOCK SW
Press door lock/unlock switch to the lock side On F
Door lock/unlock switch does not operate Off
CDL UNLOCK SW
Press door lock/unlock switch to the unlock side On
Driver's door closed Off
G
DOOR SW-DR
Driver's door opened On
Passenger door closed Off H
DOOR SW-AS
Passenger door opened On
Rear RH door closed Off
DOOR SW-RR
Rear RH door opened On I
Rear LH door closed Off
DOOR SW-RL
Rear LH door opened On
J
Back door closed Off
BACK DOOR SW
Back door opened On
“LOCK” button of Intelligent Key or door request switch are not K
Off
I-KEY LOCK pressed
“LOCK” button of Intelligent Key or door request switch are pressed On
“UNLOCK” button of Intelligent Key or door request switch are not DEF
Off
pressed
I-KEY UNLOCK
“UNLOCK” button of Intelligent Key or door request switch are
On
pressed M
Return to ignition switch to “LOCK” position Off
PUSH SW
Press ignition switch On
N
“LOCK” button of key fob is not pressed Off
KEYLESS LOCK
“LOCK” button of key fob is pressed On
“UNLOCK” button of key fob is not pressed Off O
KEYLESS UNLOCK
“UNLOCK” button of key fob is pressed On
Ignition switch ON NOMAL
After the reception of air bag deployment signal from air bag diag- P
Off
SHOCK SENSOR nosis sensor unit
During the reception of air bag deployment signal from air bag diag-
On
nosis sensor unit
Other than the following Off
UNLOCK SHOCK
During the unlock operation interlocked with air bag On

DEF-23 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status

NOTE: On
UNLOCK WITH DR
The item is indicated, but not monitored Off
Vehicle speed sensing auto door lock function does not operate Off
LOCK WITH SPEED
Vehicle speed sensing auto door lock function is operating On
Ignition switch OFF Off
ACC ON SW
Ignition switch ACC or ON On
Rear window defogger switch OFF Off
REAR DEF SW
Rear window defogger switch ON On
Lighting switch OFF Off
TAIL LAMP SW
Lighting switch 1ST On
Turn signal switch OFF Off
TURN SIGNAL R
Turn signal switch RH On
Turn signal switch OFF Off
TURN SIGNAL L
Turn signal switch LH On
Lighting switch OFF Off
HI BEAM SW
Lighting switch HI On
Lighting switch OFF Off
HEAD LAMP SW 1
Lighting switch 2ND On
Lighting switch OFF Off
HEAD LAMP SW 2
Lighting switch 2ND On
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
Lighting switch OFF Off
AUTO LIGHT SW
Lighting switch AUTO On
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On
Rear fog lamp switch OFF Off
RR FOG SW
Rear fog lamp switch ON On
Engine stopped Off
ENGINE RUN
Engine running On
Light & rain sensor is in normal condition OK
LIT-SEN FAIL
Light & rain sensor is with error NOTOK
Outside of the room is dark On
AUT LIGHT SYS
Outside of the room is bright Off
Displays a setting time of the follow
HD LIGHT TIME — me home function set by the work
support
Ignition switch OFF or ACC Off
IGN SW CAN
Ignition switch ON On
Front wiper switch OFF Off
FR WIPER HI
Front wiper switch HI On
Front wiper switch OFF Off
FR WIPER LOW
Front wiper switch LO On
Front wiper switch OFF Off
FR WIPER INT
Front wiper switch INT On

DEF-24 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
Front washer switch OFF Off
FR WASHER SW
Front washer switch ON On
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 1-7 B
Any position other than front wiper stop position Off
FR WIPER STOP
Front wiper stop position On
Rear wiper switch OFF Off C
RR WIPER ON
Rear wiper switch ON On
Rear wiper switch OFF Off
RR WIPER INT D
Rear wiper switch INT On
Rear wiper stop position Off
RR WIPER STOP
Other than rear wiper stop position On E
Rear washer switch OFF Off
RR WASHER SW
Rear washer switch ON On
F
NOTE: Off
REVERSE SW CAN
The item is indicated, but not monitored On
When headlamp washer switch is not pressed Off G
H/L WASH SW
When headlamp washer switch is pressed On
Blower fan motor switch OFF Off
FAN ON SIG H
Blower fan motor switch ON (other than OFF) On
Compressor ON is not requested from auto amp.
Off
(A/C indicator OFF, blower fan motor switch OFF or etc.)
AIR COND SW I
Compressor ON is requested from auto amp.
On
(A/C indicator ON and blower fan motor switch ON).
Hazard switch OFF Off
HAZARD SW J
Hazard switch ON On
Brake pedal is not depressed Off
BRAKE SW
Brake pedal is depressed On K
When back door opener switch is not pressed Off
TRNK OPNR SW
When back door opener switch is pressed On
DEF
Close the hood
NOTE: Off
HOOD SW Vehicles without theft warning system are OFF-fixed
Open the hood On
M

Auto lock function does not operate Off

AUTO RELOCK
Auto lock function is operating On N
The vehicle without glass break sensor Off
GLS BREAK SEN
The vehicle with glass break sensor On
• Ignition switch OFF or ACC O
Off
OIL PRESS SW • Engine running
Ignition switch ON On
P

DEF-25 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
TERMINAL LAYOUT

JSMIA0031GB

PHYSICAL VALUES
CAUTION:
• Check combination switch system terminal waveform under the loaded condition with lighting
switch, turn signal switch and wiper switch OFF is not to be fluctuated by being overloaded.
• Turn wiper intermittent dial position to 4 except when checking waveform or voltage of wiper inter-
mittent dial position. Wiper intermittent dial position can be confirmed on CONSULT-III. Refer to
BCS-28, "COMB SW : CONSULT-III Function (BCM - COMB SW)".
• BCM reads the status of the combination switch at 10 ms internal normally. Refer to BCS-9, "System
Description".

DEF-26 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

Terminal No. Description A

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
Just after Insert mechanical key B
1 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(W) Output der
of tester should move
Just after Insert mechanical key C
2 Input/ Insert mechanical key into ignition key cylin-
Ground NATS antenna amp. into ignition key cylinder. Pointer
(G) Output der
of tester should move

3 Ignition power sup- Ignition switch OFF or ACC 0V

Ground Input D
(W) ply Ignition switch ON or START Battery voltage

4 Ignition switch OFF 0V

Ground ACC power supply Input
(SB) Ignition switch ON or ACC Battery voltage E
Insert mechanical key into ignition key cylin-
5 Battery voltage
der
*1
(LG) Ground Key switch Input
Remove mechanical key from ignition key F
(R)*2 0V
cylinder

DEF

DEF-27 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4)

JPMIA0165GB

1.4 V

Lighting switch HI
(Wiper intermittent dial 4)

JPMIA0166GB

1.3 V

6 Combination switch Combination Lighting switch 2ND

Ground Input
(L) INPUT 3 switch (Wiper intermittent dial 4)

JPMIA0167GB

1.3 V

Rear washer switch ON

JPMIA0169GB

1.3 V

Any of the condition below

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 3
JPMIA0196GB

1.3 V

DEF-28 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4) C

JPMIA0165GB

1.4 V D

E
Lighting switch 1ST
(Wiper intermittent dial 4)
F
JPMIA0166GB

1.3 V
G

7 Combination switch Combination Lighting switch AUTO

H
Ground Input
(GR) INPUT 4 switch (Wiper intermittent dial 4)

JPMIA0168GB
I
1.3 V

J
Any of the condition below
with all switch OFF
• Wiper intermittent dial 1 K
• Wiper intermittent dial 6

JPMIA0169GB

1.3 V DEF

M
Rear wiper INT
(Wiper intermittent dial 4)
N
JPMIA0196GB

1.3 V
O

DEF-29 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

JPMIA0165GB

1.4 V

Turn signal switch RH

JPMIA0166GB

1.3 V

Combination
8 Combination switch switch
Ground Input Turn signal switch LH
(V) INPUT 1 (Wiper intermit-
tent dial 4)

JPMIA0167GB

1.3 V

Front wiper switch LO

JPMIA0168GB

1.3 V

Front washer switch ON

JPMIA0196GB

1.3 V

DEF-30 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF C

JPMIA0165GB

1.4 V D

Lighting switch 2ND

F
JPMIA0166GB

1.3 V
G

9 Combination
Combination switch switch
H
(G)*3 Ground Input Lighting switch PASS
INPUT 2 (Wiper intermit-
(B)*4 tent dial 4)

JPMIA0167GB
I
1.3 V

Front wiper switch INT

K

JPMIA0168GB

1.3 V DEF

Front wiper switch HI

N
JPMIA0196GB

1.3 V
O

DEF-31 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

All switch OFF

(Wiper intermittent dial 4)

JPMIA0165GB

1.3 V

Front fog lamp switch ON

(Wiper intermittent dial 4)

JPMIA0167GB

1.3 V

10 Combination switch Combination Rear fog lamp switch ON

Ground Input
(BR) INPUT 5 switch (Wiper intermittent dial 4)

JPMIA0168GB

1.3 V

Rear wiper switch ON

(Wiper intermittent dial 4)

JPMIA0169GB

1.3 V

Any of the condition below

with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2
• Wiper intermittent dial 6
• Wiper intermittent dial 7
JPMIA0196GB

1.3 V
11 Input/
Ground Audio link — — —
(B) Output

DEF-32 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

OFF
(When rear door RH C
12 Rear door closed)
Ground Rear door switch RH Input
(LG) switch RH
PKID0924E

11.2 V D
ON
(When rear door RH 0V
opened) E

F
OFF
13 Back door (When back door closed)
Ground Back door switch Input
(V) switch G
PKID0924E

11.2 V
ON H
0V
(When back door opened)

OFF
(When passenger door
14 J
Passenger door Passenger door closed)
(P)*3 Ground Input
switch switch
(BR)*4 PKID0924E

11.2 V K
ON
(When passenger door 0V
opened)
DEF

M
OFF
15 (When driver door closed)
Driver door
(BR)*3 Ground Driver door switch Input
*4
switch N
(P) PKID0924E

11.2 V
ON
O
(When driver door 0V
opened)

DEF-33 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

OFF
(When rear door LH
16 Rear door closed)
Ground Rear door switch LH Input
(GR) switch LH
PKID0924E

11.2 V
ON
(When rear door LH 0V
opened)

17 Door lock status indi- Door lock status ON 12 V

Ground Output
(L) cator indicator OFF 0V

20 Rear window defog- Rear window Not pressed

Ground Input
(SB) ger switch defogger switch

JPMIA0154GB

1.1 V
While pressing 0V
21 Input/
— CAN-L — —
(P) Output
22 Input/
— CAN-H — —
(L) Output
ON 0V

23 Security indica-
Ground Security indicator Output Blinking
(V) tor

JPMIA0014GB

10.3 V
OFF 12 V
Ignition switch OFF or ACC 12 V

24 Light & rain sensor Input/

Ground
(GR) serial link Output Ignition switch ON

JPMIA0156GB

8.7 V
25
Ground Alarm link Output — —
(G)

DEF-34 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output

26
Blower fan motor Blower fan mo- OFF C
(GR)*5 Ground Input
switch tor switch
(LG)*6
PKID0924E

11.2 V D
ON (other than OFF) 0V

E
Compressor ON is not re-
quested from auto amp.
(A/C indicator OFF, blow- F
er fan motor switch OFF
27
Ignition switch or etc.)
(P)*5 Ground A/C switch Input
*6
ON PKID0924E
(Y) 11.2 V G
Compressor ON is re-
quested from auto amp.
(A/C indicator ON and 0V H
blower fan motor switch
ON).
Ignition switch OFF or ACC 0V I

28 J
(LG)*7 Ground Shock detect sensor Input
Ignition switch ON
(R)*8
K
JPMIA0155GB

6.0 V
DEF

29
Not pressed
M
Back door opener Back door
(LG)*3 Ground Input
switch opener switch
(O)*4
JPMIA0154GB N
1.2 V
Pressed 0V
O

P
32 Door lock/unlock Door lock/un- Not pressed
Ground
(BR) switch (Unlock) Input lock switch

JPMIA0154GB

1.2 V
Pressed to the unlock side 0V

DEF-35 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

33
OFF
(W)*9 Ground Hazard switch Input Hazard switch
(Y)*10
JPMIA0154GB

1.3 V
ON 0V

34
Door lock/unlock Door lock/un- Not pressed
(SB)*3 Ground
switch (Lock) Input lock switch
(P)*4
JPMIA0154GB

1.2 V
Pressed to the lock side 0V

35 Headlamp washer Headlamp Not pressed

Ground
(G) switch Input washer switch

JPMIA0154GB

1.2 V
Pressed to the lock side 0V
All switch OFF 0V
Turn signal switch RH
Lighting switch 2ND
Combination
36 Combination switch switch Lighting switch HI
Ground Output
(G) OUTPUT 5 (Wiper intermit-
tent dial 4)
Lighting switch 1ST
JPMIA0164GB

9.1 V
All switch OFF
0V
(Wiper intermittent dial 4)
Front washer switch ON
(Wiper intermittent dial 4)
Rear washer switch ON
(Wiper intermittent dial 4)
37 Combination switch Combination
Ground Output
(R) OUTPUT 2 switch Any of the condition below
with all switch OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 5
• Wiper intermittent dial 6 JPMIA0161GB

9.1 V
Rear wiper switch ON
(Wiper intermittent dial 4)

DEF-36 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
All switch OFF 0V
B
Front wiper switch LO
Front wiper switch MIST
Combination
38 Combination switch switch Front wiper switch INT C
Ground Output
(W) OUTPUT 3 (Wiper intermit- Lighting switch AUTO
tent dial 4)

Rear fog lamp switch ON D

JPMIA0162GB

9.3 V
All switch OFF 0V
E
Turn signal switch LH
Lighting switch PASS
Combination
39 Combination switch switch Lighting switch 2ND F
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Front fog lamp switch ON G
JPMIA0163GB

9.3 V
All switch OFF
0V H
(Wiper intermittent dial 4)
Front wiper switch HI
(Wiper intermittent dial 4)
I
Any of the condition below
40 Combination switch Combination with all switch OFF
Ground Output • Wiper intermittent dial 1
(P) OUTPUT 1 switch
• Wiper intermittent dial 2 J
• Wiper intermittent dial 3
• Wiper intermittent dial 6
• Wiper intermittent dial 7 JPMIA0160GB

9.1 V
K
Rear wiper switch INT
(Wiper intermittent dial 4)
41 Battery power sup-
Ground Input Ignition switch OFF Battery voltage DEF
(LG) ply

42 Interior room lamp Interior room lamp battery saver activation 0V

Ground Output
(V) power supply Interior room lamp battery saver no activation 12 V
M
43 Rear wiper switch OFF 0V
Ground Rear wiper motor Output
(SB) Rear wiper switch ON 12 V
N

O
Rear wiper stop position
44 Ignition switch
Ground Rear wiper auto stop Input
(B) ON
JPMIA0197GB P

Any position other than

0V
rear wiper stop position

DEF-37 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output

45 Back door lock actu- Back door Pressed

Ground Output
(V) ator opener switch

SKIA9232E

Not pressed 0V
Turn signal switch OFF 0V

47 Ignition switch
Ground Turn signal LH Output
(BR) ON Turn signal switch LH

PKID0926E

6.5 V
Turn signal switch OFF 0V

48 Ignition switch
Ground Turn signal RH Output
(GR) ON Turn signal switch RH

PKID0926E

6.5 V

49 OFF 0V
Ground Rear fog lamp Output Rear fog lamp
(Y) ON 12 V

50 Unlock 5V
Ground Unlock sensor Input Driver's door
(G) lock 0V

51 Depress the brake pedal Battery voltage

Ground Stop lamp switch Input
(R) Release the brake pedal 0V

52 Room lamp timer Interior room OFF 12 V

Ground Output
(R) control lamp ON 0V

53 Power window pow- OFF or ACC 0V

Ground Output Ignition switch
(L) er supply (IGN) ON 12 V

Door unlock Pressed to the unlock side

54 Door lock/un-
Ground (All other than driv- Output
(O) lock switch
er's door)

SKIA9232E

Not pressed 0V
55
Ground Ground — Ignition switch ON 0V
(B)

DEF-38 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
Not pressed 0V
B

56 Door lock (All) and Door lock/un-

(V)
Ground
fuel lid lock
Output
lock switch
C
Pressed to the lock side

D
SKIA9232E

57 Battery power sup-

Ground Input Ignition switch OFF Battery voltage
(Y) ply
E
58 Power window pow-
Ground Output Ignition switch OFF 12 V
(P) er supply (BAT)
When lock button of key fob or Intelligent Key
0V F
59 is not pressed
Ground Super lock Output
(R) When lock button of key fob or Intelligent Key
12 V
is pressed
G

H
60 Driver's door unlock Door lock/un- Pressed to the unlock side
Ground Output
(G) and fuel lid unlock lock switch

I
SKIA9232E

Not pressed 0V
*1: With Intelligent Key J
*2: Without Intelligent Key
*3: RHD models
*4: LHD models K
*5: With gasoline engine
*6: With diesel engine
*7: RHD models with side air bag DEF
*8: LHD models with side air bag
*9: With xenon headlamp and daytime light system
*10: Except with xenon headlamp and daytime light system M

DEF-39 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (LHD MODELS) - INFOID:0000000001279896

JCLWA0524GB

DEF-40 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

DEF

JCLWA0525GB

DEF-41 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

JCLWA0526GB

DEF-42 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

DEF

JCLWA0527GB

DEF-43 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

JCLWA0528GB

DEF-44 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (RHD MODELS) - INFOID:0000000001279897

DEF

JCLWA0529GB
P

DEF-45 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

JCLWA0530GB

DEF-46 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

DEF

JCLWA0531GB

DEF-47 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

JCLWA0532GB

DEF-48 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

DEF

JCLWA0533GB

Fail Safe INFOID:0000000001551375 P

FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC is detected.

DEF-49 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >

DTC Fail-safe Cancellation

• Inhibits engine cranking
B2190: NATS ANTENNA AMP • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
B2191: DIFFERENCE OF KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
B2192: ID DISCORD BCM-ECM Fuel cut (ECM) Erase DTC
B2193: CHAIN OF BCM-ECM Fuel cut (ECM) Erase DTC
• Inhibits engine cranking
B2194: DISCORD BCM-I-KEY • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
B2195: ANTI SCANNING • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)
• Inhibits engine cranking
B2196: DONGLE NG • Inhibits steering lock unlocking (Intelligent Key unit) Erase DTC
• Fuel cut (ECM)

REAR WIPER MOTOR PROTECTION

BCM detects the rear wiper stopping position according to the rear wiper auto stop signal.
When the rear wiper auto stop signal does not change more than 5 seconds while driving the rear wiper, BCM
stops power supply to protect the rear wiper motor.
Condition of cancellation
1. Turn ignition switch OFF.
2. Pass more than 1 minute after the rear wiper stop.
3. Turn ignition switch ON.
4. Operate the rear wiper switch.
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status from the terminal voltage.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating.
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY LIGHT & RAIN SENSOR MALFUNCTION
BCM detects the light & rain sensor serial link error and the light & rain sensor malfunction.
BCM controls the following fail-safe when light & rain sensor has a malfunction.
Fail-safe Control
• Auto light control: Headlamp is turned ON.
• Front wiper control: The condition just before the activation of fail-safe is maintained until the front wiper
switch is turned OFF.
DTC Inspection Priority Chart INFOID:0000000001551376

Priority DTC
• U1000: CAN COMM CIRCUIT
1
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERNCE OF KEY
• B2192: ID DISCORD BCM-ECM
2 • B2193: CHAIN OF BCM-ECM
• B2194: DISCORD BCM-I-KEY
• B2195: ANTI SCANNING
• B2196: DONGLE NG

DEF-50 GETtheMANUALS.org
 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS >
DTC Index INFOID:0000000001551377

A
NOTE:
Details of time display
• CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning igni- B
tion switch OFF → ON again.
• PAST: Displays when there is a malfunction that is detected in the past and stored.
• 1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
→ 2 → 3...38 → 39 after returning to the normal condition whenever ignition switch OFF → ON. The counter C
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF → ON after returning to the normal condition if the malfunction is detected again.
D
DTC TIME Fail-safe Reference
U1000: CAN COMM CIRCUIT 0 1 - 39 — BCS-33
U1010: CONTROL UNIT (CAN) 0 1 - 39 — BCS-34 E
• With Intelligent Key system: SEC-41
B2190: NATS ANTENNA AMP CRNT PAST × • Without Intelligent Key system: SEC-
254 F
• With Intelligent Key system: SEC-43
B2191: DIFFERENCE OF KEY CRNT PAST × • Without Intelligent Key system: SEC-
256
G
• With Intelligent Key system: SEC-38
B2192: ID DISCORD BCM-ECM CRNT PAST × • Without Intelligent Key system: SEC-
251
H
• With Intelligent Key system: SEC-40
B2193: CHAIN OF BCM-ECM CRNT PAST × • Without Intelligent Key system: SEC-
253
B2194: DISCORD BCM-I-KEY CRNT PAST × SEC-53 I
• With Intelligent Key system: SEC-54
B2195: ANTI SCANNING CRNT PAST × • Without Intelligent Key system: SEC-
264 J
• With Intelligent Key system: SEC-55
B2196: DONGLE NG CRNT PAST × • Without Intelligent Key system: SEC-
265 K

DEF

DEF-51 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference Value INFOID:0000000001551380

VALUES ON THE DIAGNOSIS TOOL

Monitor Item Condition Value/Status

Changes depending on engine
coolant temperature, air condition-
MOTOR FAN REQ Engine idle speed 1-4
er operation status, vehicle speed,
etc.
A/C switch OFF Off
AC COMP REQ Engine running A/C switch ON
On
(Compressor is operating)
Lighting switch OFF Off
TAIL&CLR REQ
Lighting switch 1ST, 2ND or AUTO (Light is illuminated) On
Lighting switch OFF Off
HL LO REQ
Lighting switch 2ND or AUTO (Light is illuminated) On
Lighting switch OFF Off
HL HI REQ
Lighting switch HI (Light is illuminated) On

Lighting switch 2ND or Front fog lamp switch OFF Off

FR FOG REQ
AUTO (Light is illuminated) Front fog lamp switch ON On

HL WASHER REQ Front washer switch OFF Off

NOTE: Ignition switch ON, and low Front washer switch ON
This item is monitored only on the vehicle beam headlamp is ON (When headlamp washer is operat- On
with headlamp washer. ing)
Front wiper switch OFF Stop
Front wiper switch INT 1LOW
FR WIP REQ Ignition switch ON
Front wiper switch LO Low
Front wiper switch HI Hi
Front wiper stop position STOP P
WIP AUTO STOP Ignition switch ON Any position other than front wiper
ACT P
stop position
Front wiper operates normally Off
WIP PROT Ignition switch ON Front wiper stops at fail-safe oper-
BLOCK
ation

ST RLY REQ When Intelligent Key is outside the vehicle, and the push switch
Off
NOTE: is pushed
Vehicle without Intelligent Key system indi- When Intelligent Key is inside the vehicle, and the push switch is
cates only “ON”, and it does not change. On
pushed
Ignition switch OFF or ACC Off
IGN RLY
Ignition switch ON On
Rear window defogger switch OFF Off

RR DEF REQ Ignition switch ON Rear window defogger switch ON

(Rear window defogger is operat- On
ing)
Ignition switch OFF, ACC or engine running Open
OIL P SW
Ignition switch ON Close

DEF-52 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Monitor Item Condition Value/Status
A
NOTE:
REV SW Off
This item is indicated, but not monitored.
Daytime running light system is not operated with lighting switch
DTRL REQ Off B
OFF.
NOTE:
This item is monitored only on the vehicle Any of the condition below
with the daytime running light system. • Daytime running light system is operated. On
• Lighting switch 1ST, 2ND or AUTO (Light is illuminated) C
HOOD SW Close the hood Off
NOTE:
This item is monitored only on the vehicle Open the hood On D
with the vehicle security system.
THFT HRN REQ Not operation Off
NOTE:
This item is monitored only on the vehicle E
Horn is activated with vehicle security system. On
with the vehicle security system.
NOTE:
HORN CHIRP Off
This item is indicated, but not monitored. F

TERMINAL LAYOUT
G

DEF

JPMIA0311ZZ

PHYSICAL VALUES

DEF-53 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

Terminal No. Description

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
1
Ground Battery power supply Input Ignition switch OFF Battery voltage
(G)
2
Ground Battery power supply Input Ignition switch OFF Battery voltage
(R)
3 When engine is clanking Battery voltage
(O)*1 Ground Starter relay power supply Output
When engine is not clanking 0V
(BR)*2

4 Cooling fan relay-1 power Cooling fan opera- OFF 0V

Ground Output
(W) supply tion MID or HI Battery voltage

5 Ignition switch OFF, ACC or ON 0V

Ground Ignition switch START Input
(R) Ignition switch START Battery voltage
6 Battery power supply
Ground Input Ignition switch OFF Battery voltage
(BR) (Cooling fan relay)

7 Cooling fan motor-2 (HI) Cooling fan opera- OFF Battery voltage
Ground —
(P) ground tion HI 0V

8 Cooling fan relay-2 power Cooling fan opera- OFF 0V

Ground Output
(G) supply tion HI Battery voltage
11
Ground Ground — Ignition switch ON 0V
(B)
Rear window defogger
12 0V
Rear window defogger re- switch OFF
3
(O)* Ground Output Ignition switch ON
lay power supply Rear window defogger
(G)*4 Battery voltage
switch ON
• Parking lamp Turn off Battery voltage
15*5 Ground
Daytime running light relay
Output
• License plate
(SB) control lamp Turn on 0V
• Tail lamp

16*6 Front fog lamp switch OFF 0V

Ground Front fog lamp (LH) Output Lighting switch 1ST
(Y) Front fog lamp switch ON Battery voltage

17*6 Front fog lamp switch OFF 0V

Ground Front fog lamp (RH) Output Lighting switch 1ST
(W) Front fog lamp switch ON Battery voltage

18 Lighting switch OFF 0V

Ground Headlamp LO (LH) Output
(L) Lighting switch 2ND Battery voltage

19*7 Headlamp aiming motor Lighting switch OFF 0V

Ground Output
(R) power supply Lighting switch 2ND Battery voltage

20 Lighting switch OFF 0V

Ground Headlamp LO (RH) Output
(SB) Lighting switch 2ND Battery voltage
Lighting switch OFF 0V
21
Ground Headlamp HI (LH) Output • Lighting switch 2ND and HI
(G) Battery voltage
• lighting switch PASS
Lighting switch OFF 0V
22
Ground Headlamp HI (RH) Output • Lighting switch 2ND and HI
(LG) Battery voltage
• lighting switch PASS

23 Engine stopped 0V
Ground Oil pressure switch Input Ignition switch ON
(W) Engine running Battery voltage

DEF-54 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value A
Input/ Condition
Signal name (Approx.)
+ − Output
Front wiper stop position 0V
24
Ground Front wiper auto stop Input Ignition switch ON
B
(Y) Any position other than
Battery voltage
front wiper stop position
25
Ground Ground — Ignition switch ON 0V C
(B)
26 Input/
— CAN-L — —
(P) Output
D
27 Input/
— CAN-H — —
(L) Output

31 Cooling fan opera- OFF Battery voltage

Ground Cooling fan relay-4 control Output E
(V) tion LO 0V
After passing approximately 2 seconds or more
Battery voltage
after turning the ignition switch from ON to OFF
32* 1 F
Ground ETC relay control Input • Ignition switch ON
(LG)
• For approximately 2 seconds after turning igni- 0V
tion switch from ON to OFF
G
Ignition switch OFF 0V
33*1 Ground Fuel pump relay control Input Engine stopped Battery voltage
(GR) Ignition switch ON
Engine running 0.8 V H
34* 8 Close the hood Battery voltage
Ground Hood switch Input
(Y) Open the hood 0V
When headlamp washer is I
Battery voltage
35*9 Headlamp washer relay not operating
Ground Output Ignition switch ON
(W) control When headlamp washer is
0V J
operating

37 Tail, license plate lamps Lighting switch OFF 0V

Ground Output
(R) and illuminations Lighting switch 1ST Battery voltage
K
38*10 Lighting switch OFF 0V
(O)*1 Ground Parking lamp (LH) Output
2 Lighting switch 1ST Battery voltage
(GR)* DEF
39*10 Lighting switch OFF 0V
Ground Parking lamp (RH) Output
(GR) Lighting switch 1ST Battery voltage

40 Ignition switch OFF or ACC 0V M

Ground Ignition relay power supply Output
(V) Ignition switch ON Battery voltage
41 Ignition switch OFF or ACC 0V
N
(O)*1 Ground Ignition relay power supply Output
2 Ignition switch ON Battery voltage
(L)*

42 Front wiper switch OFF 0V

Ground Front wiper HI Output Ignition switch ON O
(L) Front wiper switch HI Battery voltage

43 Front wiper switch OFF 0V

Ground Front wiper LO Output Ignition switch ON
(G) Front wiper switch LO Battery voltage P
Ignition switch ON Selector lever “P” or “N” Battery voltage
45 (Except M/T mod- Selector lever in any posi-
Ground Starter relay power supply Input els) 0V
(Y) tion other than “P” or “N”
Ignition switch ON (M/T models) Battery voltage

DEF-55 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ − Output
• Ignition switch OFF or ACC
• After passing approximately 1 second or more 0V
46*1 Fuel pump relay power after turning the ignition switch ON
Ground Output
(W) supply • For approximately 1 second after turning the
ignition switch ON Battery voltage
• Engine running
After passing approximately 20 seconds or more
0V
47 after turning the ignition switch from ON to OFF
(BR)*1 Ground ECM relay power supply Output • Ignition switch ON
(G)*2 • For approximately 20 seconds after turning ig- Battery voltage
nition switch from ON to OFF
After passing approximately 20 seconds or more
0V
48 after turning the ignition switch from ON to OFF
1
(R)* Ground ECM relay power supply Output • Ignition switch ON
(V)*2 • For approximately 20 seconds after turning ig- Battery voltage
nition switch from ON to OFF

50 Cooling fan opera- OFF Battery voltage

Ground Cooling fan relay-5 control Output
(G) tion MID or HI 0V
After passing approximately 20 seconds or more
Battery voltage
after turning the ignition switch from ON to OFF
51
Ground ECM relay control Output • Ignition switch ON
(W)
• For approximately 20 seconds after turning ig- 0V
nition switch from ON to OFF
After passing approximately 2 seconds or more
0V
after turning the ignition switch from ON to OFF
52*1 Ground ETC relay power supply Output
(P) • Ignition switch ON
• For approximately 2 seconds after turning igni- Battery voltage
tion switch from ON to OFF
Engine stopped 0V
A/C switch OFF 0V
55
Ground A/C relay power supply Output
(O) Engine running A/C switch ON
(A/C compressor is oper- Battery voltage
ating)

56 Ignition switch OFF or ACC 0V

Ground Ignition switch ON Input
(L) Ignition switch ON Battery voltage

57*8 The horn is not activated Battery voltage

Ground Horn relay control Output
(V) The horn is activated 0V

58 Ignition switch OFF or ACC 0V

Ground Ignition relay power supply Output
(Y) Ignition switch ON Battery voltage

59 Ignition switch OFF or ACC 0V

Ground Ignition relay power supply Output
(GR) Ignition switch ON Battery voltage

60 Ignition switch OFF or ACC 0V

Ground Ignition relay power supply Output
(SB) Ignition switch ON Battery voltage
61
Ground ECM power supply Output Ignition switch OFF Battery voltage
(O)

*1: MR engine and QR engine models

*2: M9R engine models
*3: MR engine models
*4: QR engine and M9R engine models

DEF-56 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
*5: With daytime running light system
*6: With front fog lamp system A
*7: Halogen type headlamp
8
* : With vehicle security system
B
*9: With headlamp washer system
*10: Without daytime running light system
C
Wiring Diagram - DEFOGGER CONTROL SYSTEM (LHD MODELS) - INFOID:0000000001279902

DEF

JCLWA0524GB

DEF-57 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

JCLWA0525GB

DEF-58 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

DEF

JCLWA0526GB

DEF-59 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

JCLWA0527GB

DEF-60 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

DEF

JCLWA0528GB

DEF-61 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >
Wiring Diagram - DEFOGGER CONTROL SYSTEM (RHD MODELS) - INFOID:0000000001279903

JCLWA0529GB

DEF-62 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

DEF

JCLWA0530GB

DEF-63 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

JCLWA0531GB

DEF-64 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

DEF

JCLWA0532GB

DEF-65 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

JCLWA0533GB

Fail Safe INFOID:0000000001551382

CAN communication control

When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If no CAN communication is available with ECM

DEF-66 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

Control part Fail-safe in operation A

• The cooling fan relay-1, the cooling fan relay-2, the cooling fan relay-3 and the cooling
fan relay-5 turn ON when the ignition switch is turned ON
Cooling fan • The cooling fan relay-1, the cooling fan relay-2, the cooling fan relay-3 and the cooling
B
fan relay-5 turn OFF when the ignition switch is turned OFF
• Cooling fan relay-4 OFF
A/C compressor A/C relay OFF
C
If no CAN communication is available with BCM

Control part Fail-safe in operation D

• The headlamp low relay turns ON when the ignition switch is turned ON
Headlamp • The headlamp low relay turns OFF when the ignition switch is turned OFF
• Headlamp high relay OFF
E
• Parking lamps • The tail lamp relay and the daytime running light relay*1 turn ON when the ignition
• License plate lamps switch is turned ON
• Tail lamps • The tail lamp relay and the daytime running light relay*1 turn OFF when the ignition
• Illuminations F
switch is turned OFF
• The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
Front wiper • The front wiper is operated at LO speed until the ignition switch is turned OFF if the G
fail-safe control is activated while the front wiper is set in the INT mode and the front
wiper motor is operating.
Front fog lamps Front fog lamp relay OFF H
Starter motor Starter relay OFF
Rear window defogger Rear window defogger relay OFF
2
I
Headlamp washer* Headlamp washer relay OFF

Horn*3 Horn relay OFF

NOTE: J
• *1: With daytime running light system
• *2: With headlamp washer system
• *3: With vehicle security system K

Ignition relay malfunction detection function

• IPDM E/R monitors status of ignition relay by the voltage at ignition relay contact circuit inside it.
• IPDM E/R judges that the ignition relay is error, if status of the ignition relay and ignition switch ON signal DEF
(CAN) *.
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay and daytime run-
ning light relay* for 10 minutes to alert the user to the ignition relay malfunction when the ignition switch is M
turned OFF.

Tail lamp relay and daytime

DTC Ignition switch Ignition relay N
running light relay*
— ON ON —
— OFF OFF — O
— OFF ON ON (10 minutes)
B2099: IGN RLY OFF ON OFF —
NOTE: P
• The tail lamp relay and the daytime running light relay* are turned OFF when the ignition switch is turned ON.
• *: With daytime running light system

Front wiper control

IPDM E/R detects the front wiper stop position with the front wiper auto stop signal.
When the front wiper auto stop signal is in the conditions listed below, IPDM E/R repeats a front wiper 10 sec-
onds operation and 20 seconds stop five times.

DEF-67 GETtheMANUALS.org
 IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
< ECU DIAGNOSIS >

Ignition switch Front wiper switch Front wiper auto stop signal
The front wiper auto stop signal (stop posi-
OFF
tion) cannot be input for 10 seconds.
ON
The front wiper auto stop signal does not
ON
change for 10 seconds.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
DTC Index INFOID:0000000001551383

CONSULT display Fail-safe TimingNOTE Reference page

No DTC is detected.
further testing — — — —
may be required.
U1000: CAN COMM CIRCUIT × CRNT PAST PCS-13
B2099: IGN RELAY OFF — CRNT PAST PCS-14
NOTE:
The details of time display are as follows.
• CRNT: The malfunctions that are detected now.
• PAST: The number is indicated when it is normal at present and a malfunction was detected in the past.

DEF-68 GETtheMANUALS.org
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT OPER-
ATE.
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
REAR WINDOW DEFOGGER AND DOOR MIRROR DEFOGGER DO NOT
OPERATE.
B
Diagnosis Procedure INFOID:0000000001279907

1.IPDM E/R AUTO ACTIVE TEST C

Check IPDM E/R active test.
Refer to DEF-8, "Diagnosis Description".
Is the inspection result normal? D
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
E
2.CHECK REAR WINDOW DEFOGGER SWITCH
Check rear window defogger switch.
Refer to DEF-13, "Component Function Check". F
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts. G
3.CHECK REAR WINDOW DEFOGGER RELAY
Check rear window defogger relay.
Refer to DEF-15, "Component Function Check" H
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace the malfunctioning parts. I

4.CHECK REAR WINDOW DEFOGGER

Check rear window defogger. J
Refer to DEF-16, "Component Function Check"
Is the inspection result normal?
YES >> GO TO 5. K
NO >> Repair or replace the malfunctioning parts.
5.CONFIRM THE OPERATION
DEF
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident" M
NO >> GO TO 1.

DEF-69 GETtheMANUALS.org
 REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR MIR-
ROR DEFOGGER OPERATE.
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER DOES NOT OPERATE BUT BOTH OF DOOR
MIRROR DEFOGGER OPERATE.
Diagnosis Procedure INFOID:0000000001279906

1.CHECK REAR WINDOW DEFOGGER

Check rear window defogger.
Refer to DEF-16, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident"
NO >> GO TO 1.

DEF-70 GETtheMANUALS.org
 DOOR MIRROR DEFOGGER DOES NOT OPERATE
< SYMPTOM DIAGNOSIS >
DOOR MIRROR DEFOGGER DOES NOT OPERATE
A
BOTH SIDE
BOTH SIDE : Diagnosis Procedure INFOID:0000000001505786
B
1.CHECK DOOR MIRROR DEFOGGER CIRCUIT
Check door mirror defogger circuit.
Refer to DEF-18, "DRIVER SIDE : Component Function Check" C
Is the inspection result normal?
YES >> GO TO 2.
D
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
Confirm the operation again. E
Is the result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident"
NO >> GO TO 1. F
DRIVER SIDE
DRIVER SIDE : Diagnosis Procedure INFOID:0000000001279909 G

1.CHECK DRIVER SIDE DOOR MIRROR DEFOGGER

Check driver side door mirror defogger. H
Refer to DEF-19, "DRIVER SIDE : Component Inspection".
Is the inspection result normal?
YES >> GO TO 2. I
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
J
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident" K
NO >> GO TO 1.
PASSENGER SIDE
DEF
PASSENGER SIDE : Diagnosis Procedure INFOID:0000000001505787

1.CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER.

M
Check passenger side door mirror defogger.
Refer to DEF-21, "PASSENGER SIDE : Component Inspection"
Is the inspection result normal?
N
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION O
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident" P
NO >> GO TO 1.

DEF-71 GETtheMANUALS.org
 REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WINDOW
DEFOGGER OPERATES
< SYMPTOM DIAGNOSIS >
REAR WINDOW DEFOGGER SWITCH DOES NOT LIGHT, BUT REAR WIN-
DOW DEFOGGER OPERATES
Diagnosis Procedure INFOID:0000000001279911

1.CHECK REAR WINDOW DEFOGGER INDICATOR

Check rear window defogger ON signal.
Refer to DEF-22, "Component Function Check".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident"
NO >> GO TO 1.

DEF-72 GETtheMANUALS.org
 PRECAUTIONS
< PRECAUTION >
PRECAUTION A
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT B
PRE-TENSIONER" INFOID:0000000001558758

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. E
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G

DEF

DEF-73 GETtheMANUALS.org
 FILAMENT
< ON-VEHICLE REPAIR >
ON-VEHICLE REPAIR
FILAMENT
Inspection and Repair INFOID:0000000001279914

INSPECTION
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.

SEL122R

2. Attach probe circuit tester (in Volt range) to middle portion of

each filament.

SEL263

3. If a filament is burned out, circuit tester registers 0 or battery

voltage.
4. To locate burned out point, move probe to left and right along fil-
ament. Test needle will swing abruptly when probe passes the
point.

SEL265

REPAIR
REPAIR EQUIPMENT
• Conductive silver composition (Dupont No. 4817 or equivalent)

DEF-74 GETtheMANUALS.org
 FILAMENT
< ON-VEHICLE REPAIR >
• Ruler 30 cm (11.8 in) long
• Drawing pen A
• Heat gun
• Alcohol
• Cloth
B
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a
cloth dampened in alcohol. C
2. Apply a small amount of conductive silver composition to tip of
drawing pen.
Shake silver composition container before use. D
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
E

PIIA0215E

F
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be conducted 10 minutes after silver
composition is deposited. G
Do not touch repaired area while test is being conducted.

I
SEL012D

5. Apply a constant stream of hot air directly to the repaired area J

for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet. K
If a heat gun is not available, let the repaired area dry for 24
hours.
DEF

M
SEL013D

DEF-75 GETtheMANUALS.org