Transfer Gear Pumps

BT, BTH
 Transfer Gear Pumps BT, BTH

Construction

Basic construction of BT (rear bearing cover removed)

Housing Driving shaft

Shaft sealing by packed gland /

Mechanical seal

Stuffing-box cover

Gearing with journals

Transfering medium inlet or outlet

Basic construction of BTH (rear bearing cover removed)

Heating liquid outlet

Housing

Heating chamber Driving shaft

Shaft sealing by packed gland

Pumping chamber
Stuffing-box cover

Gearing with journals

Transfering medium inlet or outlet

Heating liquid inlet

(left or right optional)

2 KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu
Transfer Gear Pumps BT, BTH

Function

Pumps series BT and BTH are low speed gear pumps The pump transfer chamber is heated by circulating
for transfering medium and high viscosity fluids, heat transfer fluid or steam through the jacket.
provided they have certain minimum amount of
The standard range of models is complimented by a
lubricating property, do not contain any solids and
range of a special models described below.
are chemically compatable with the materials of
construction. The pump size BT 2 can be supplied in a corrosion
The standard material of construction for housing, and acid - resistant construction (stainless steel body
bearing cover and stuffing box cover is grey cast iron. and gear) with carbone plain bearings bushes; the
The shafts and gears are manufactured from case operating pressure of this pump is limited to 5 bars.
hardening steel, hardened and ground. BT 1 up to BT 4 pumps can be manufactured with
The shafts are carried in plain bearings manufactured bronze housing and with further combinations of
in bronze, with an option of sintered iron. stainless steel gears and shafts or bronze gears and
The rotary shaft seal is a packed gland consisting of stainless steel shafts.
PTFE fillied aramid yarn, and the static sealing between
For use on liquids with an abrasive nature and
mating parts is by means of either, liquid sealant or
high corrosive effects like resins, certain paints and
gaskets. All sealing materials are asbestos free.
varnishes as well as glues a special construction,
External axial loads are not permissable, restricted Code No. / 04, is recommended, which is available
radial loads can be absorbed, dependant on their for pump sizes BT 1 up to BT 7.
magnetude and direction.
In this model all pump parts which are in contact
Driving by flexible shaft coupling is preferred. with the transfering fluid are protected from wear
In the case of fluids which require elevated tempera- and corrosion by a chemically deposited Ni/SiC-
tures to flow i. e. bitumen, wax etc. the BTH series dispersion layer. This treatment substantially
pump should be used. In this model the housing is extends the service life compared with that of a
double walled to provide a heating jacked. standard model when used in these types of fluid.

KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu 3
 Transfer Gear Pumps BT, BTH

General Characteristics
Fixing type Foot mounting
Pipe connection BT: Whitworth-Pipe thread
BTH : Whitworth-Pipe thread flange,
flange with counterflange
Direction of rotation BT = clockwise and anticlockwise
BTH = clockwise or anticlockwise
Weight see page 11 ... 15
Fitting position horizontal
Ambient temperature ϑu min = -- 10 °C
ϑu max = 60 °C

Operating Characteristics
Operating pressure
Inlet port pe min = -- 0.4 bar
Outlet port * pN = 8 bar
1 bar to BT 0
5 bar to BT 2 stainless steel
max. pressure in the heating jacket pH = 10 bar
Temperature range ϑm min = -- 10 °C
ϑm max = 220 °C
Viscosity range νmin = 76 mm 2/s
νmax = 30 000 mm 2/s
Viscosities other than within this range on request
Discharge flow see table page 9, 10
Power input speeds nmin = 100 1/min
nmax = 750 1/min

Suitable Fluids
Lubricating-, Cutting oils Waste oils Adhesives, Plastics Cellulose
Soluble-, Steel hardening-, Bitumen Binding agents etc.
Rolling-, Drawing oils Paints Resins
Diesel oils Greases Glue, Glue liquors
Fuel oil S Synthetic resin varnishes Molasses
Engine oils Nitrocellulose lacquers Waxes

Other Types
Pump with electric motor, coupling and coupling guard mounted on a common base plate.

Accessories
Flexible coupling

* higher operating pressure on request

4 KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu
Transfer Gear Pumps BT, BTH

Type Key

BT 0 B Z 0 A C 51/ .
BT 2 B Z 0 R T 51/ .
S
BT 1...4 B Z 0 U T 51/ .
B
BT 1...7 B Z 0 C K 51/ .
BT 1...7 B Z 0 C K 51/ 04
R B
BTH 1+ 2 L . 0 C K 51 .
R B
BTH 3 L . 0 C F 51 .

Code-No. for
special construction
04 Wear and corrosion
protected model
Kind of sealing (Packing)
51 Arolan
Construction of gear unit
C Steel shafts and gear unhardened
K Steel shafts and gear hardened
F Steel shafts and gear hardened
S Stainless steel shaft (material No. 1.4057)
bronze gear
T Stainless steel shafts and gear heat treated
(material No. 1.4057)

Construction of housing and friction bearing

A Cast iron without bearing bush
B Cast iron with Bz bearing bush
C Iron bearing bush
U Bronze without bearing bush
R Stainless steel with carbon-bearing bush (mat. No. 1.4308)
Design code
0 (specified by KRACHT)
Pipe connection
Z Whitworth pipe thread
F Flange
G Flange with counter flange

Direction of rotation
R Clockwise
L Anticlockwise
B Clockwise and anticlockwise
Series
Product code
BT without heating jacket (Cylindrical shaft end without step bearing, with packing and threaded pipe connection)
BTH with heating jacket (Cylindrical shaft end without step bearing, with packing, threated pipe- or flange connection)

KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu 5
 Transfer Gear Pumps BT, BTH

Identification in accordance with

Transfer Gear Pumps BT – ATEX EC Directive RL 94/9/EG

Pumps of the series BT are also available Manufacturer: Kracht GmbH

in ATEX design. 58791 Werdohl, Germany
The pumps can be used as follows: Type designation: BT …
a. In Zone 2 (Gas- , Category 3G) Job No., Production Date: xxxxxx / xx-xxx xx.xx
in explosion groups IIA and IIB and IIC Tech. File Ref. : TFR: 07.01X
b. In Zone 1 (Gas- , Category 2G) Ignition protection
in explosion groups IIA and IIB and IIC designation: II 2 G ck T4
Qualification with regard to surface temperature is T4. The ATEX design BT pumps are equipped with a
For all gases, vapours, mists with an ignition mechanical seal with a fluid receiver. In the area of
temperature > 135 °C, the pumps are not an ignition the fluid receiver the BT-ATEX has a connection for
source. a container for filling the receiver fluid. An overflow
The permissible temperature range extends from serves to monitor the amount which leaks from
-- 20 °C ≤ Ta ≤ 60 °C. mechanical seal.

Construction BT – ATEX

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
2008

19 20

1 Overflow
6 Fluid gasket 11 O-Ring 16 Bearing
2 Container for
the preliminary fluid 7 Driven shaft 12 Seal retainer 17 Rotary shaft seal
3 Earth connection 8 Housing 13 Mechanical seal 18 Parallel key
4 Front cover 9 Driving shaft 14 Vent screw 19 Screw plug
5 Plain bearing bush 10 Cover 15 Drain plug 20 Antitwist protection

6 KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu
Transfer Gear Pumps BT, BTH

Transfer Gear Pumps BT – ATEX

General Characteristics

Design External gear pump Filtering Filter fineness ≤ 60 µm

Pipe connection Whitworth-Pipe thread (If required, install a suction filter
to prevent the pump from being
Mounting position Horizontal jammed by foreign particles).
Fixing type Foot mounting Permissible media Inflammable and non-inflammable
Direction of rotation clockwise and anticlockwise liquids without abrasive ingredients
Ambient temperature ϑ u min -- 10 °C which are compatible with the
materials of which the pump is made.
ϑ u max 40 °C
The liquid must not be static
charged. Flame point and mini-
mum ignition temperature must
Operating Characteristics be observed by the operator.
Media-specific characteristics
Temperature range ϑ u min -- 10 °C must be taken into consideration.
ϑ u max 60 °C The fluid must have a minimum
Temperature amount of lubricity.
of delivered medium ϑu min -- 10 °C
ϑu max 80 °C
Speed nmin 100 1/min For certain operating conditions,
the stated minimum and maximum
nmax 750 1/min
values are not valid! Thus, for example,
Viscosity νmin 76 mm2/s the maximum operating pressure is not
νmax 20000 mm2/s permissible in conjunction with low
rpm and minimum viscosity.
Operating pressure
Inlet port pe min -- 0.4 bar Media-specific characteristics must be
pe max 1 bar observed, e.g. in the case of emulsions
and solutions containing water,
Outlet port pn max 8 bar
the maximum operating temperature
Axial and centrifugal is 50 °C, the pump must be located
forces on shaft end Not allowed beneath the level of the liquid.

Materials
Housing, bearings, gears see type key*
Mechanical sealing SiC-SiC, FFKM, Stainless steel
Other media-side seals Loctite 510, FEP with FKM-core
Uni-oiler Ms, Plexiglas
Type plate Stainless steel
Notched nail Al (Mg portion < 7.5 %)
Gasket ring screw-plugs Cu
Other parts St

* see type label at pump: BT...

KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu 7
 Transfer Gear Pumps BT, BTH

Type Key ATEX

S
BT 1...4 B Z 0 U T 59/ . - ATEX
B
BT 1...7 B Z 0 C K 59/ . - ATEX
BT 1...7 B Z 0 C K 59/ 04 - ATEX

Code-No. for
special construction
04 Wear and corrosion
protected model

Seals
59 Mechanical seal
with liquid seal

Construction of gear unit

K Steel shafts and gear hardened
F Steel shafts and gear hardened
S Stainless steel shaft (material No. 1.4057)
bronze gear
T Stainless steel shafts and gear heat treated
(material No. 1.4057)

Construction of housing and friction bearing

B Cast iron with Bz bearing bush
C Iron bearing bush
U Bronze without bearing bush

Design code
0 (specified by KRACHT)

Pipe connection
Z Whitworth pipe thread

Direction of rotation
B Clockwise and anticlockwise

Series

Product code
BT (without heating jacket)

8 KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu
Transfer Gear Pumps BT, BTH

Power consumption

Viscosity ν (mm2/s) Viscosity ν (mm2/s) Viscosity ν (mm2/s)

Pump type

reg. power input P (kW) reg. power input P (kW) reg. power input P (kW)

BT 0

BT 1

BT 2

BT 3

BT 4

BT 5

BT 6

BT 7

BTH 1/55

BTH 1/105

BTH 2/100

BTH 2/130

BTH 3/150

Power input required at high viscosities

Viscosities above values specified in the table require a higher

power input.
In such cases the power input of the pump P1Pu can be determined
by means of the viscosity factor fν (see table page 10) as follows:
P1Pu = PTab 76 + fν · QTab
Example: BT 4 n = 200 1/min; ν = 10 000 mm2/s; p = 8 bar
with Ptab 76 = 0.6 kW, table data at ν = 76 mm2/s
fν = 27 x 10-3 kW min/l
QTab = 32 l/min
gives power input P1Pu = 1.46 kW

KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu 9
 Transfer Gear Pumps BT, BTH

Power consumption

Viscosity ν (mm2/s) Viscosity ν (mm2/s) Viscosity ν (mm2/s) Viscosity ν (mm2/s)

Pump type

reg. power input P (kW) reg. power input P (kW) reg. power input P (kW) reg. power input P (kW)

BT 0

BT 1

BT 2

BT 3

BT 4

BT 5

BT 6

BT 7

BTH 1/55

BTH 1/105

BTH 2/100

BTH 2/130

BTH 3/150

kin. viscosity
ν< 1000 2000 3000 6000 10000 20000 30000
mm2/s
Max. speed
nmax ≥ 750 600 500 400 300 200 100
1/min
Viscosity factor
fν 9.5 14 17 22.5 27 34 38
10-3 kW min/l

Spread of output: Important:

± 5 % of table values Q. Viscosities below 76 mm2/s When determining the power input
effect a decrease of output flow values, Q. required always consider the
The power output of driving motor must exceed max. operating viscosity.
(e. g. in the starting situation) !
the table values P by about 20 %.

10 KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu
Transfer Gear Pumps BT, BTH

Dimensions

BT 0 BZ OAC 51

BT 1...7 BZ O.. 51
BT 1...7 BZ OCK 51/ 04

Groove for retaining ring acc. to standard DIN 471

Parallel key acc. to DIN 6885

Shaft end approx.

Pump
R A B C D ØE F G H O J K P Ød l m n u t d1 l1 Z Weight
type
kg

BT 0 G 1⁄ 4 30 60 45 65 11 15 65 60 47 38 95 88 13 22 – – – – – – 11 2

BT 1 G 1⁄ 2 – 45 55 75 9 12 85 69 54 48 150 100 13 40 15 10 5 15 M6 15 20 3

BT 2 G 3⁄ 4 35 55 65 90 10 12 90 88,5 71 65 165 125 15 45 25 5 5 17 M6 15 20 5

BT 3 G1 40 65 85 105 10 12 100 111 88,5 70 190 155 18 50 30 5 6 20,5 M6 15 23 7

BT 4 G 11⁄2 40 80 95 135 10 12 130 131,5 100 102 245 189 25 50 40 5 8 28 M8 20 28 15

BT 5 G 1 1⁄ 2 35 75 140 180 14 20 150 145 103 98 250 213 25 50 40 5 8 28 M8 20 29 20

BT 6 G2 35 75 185 225 14 28 175 175 126 106 245 252 25 50 40 5 8 28 M8 20 29 29

BT 7 G2 60 100 185 225 14 28 240 175 126 123 260 252 25 50 40 5 8 28 M8 20 29 37

Inlet and outlet ports equally sized.

KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu 11
 Transfer Gear Pumps BT, BTH

Dimensions

55
BTH 1 / 155 • ZO • K 51

Outlet port for heating liquids **

Parallel key acc. to DIN 6885

Inlet port for heating liquids

Clockwise or anticlockwise by
choice unused connection is to be sealed

55
BTH 1 / 105 • FO • K 51

Outlet port for heating liquids **

Parallel key acc. to DIN 6885

Inlet port for heating liquids

Clockwise or anticlockwise by
choice unused connection is to be sealed

55
BTH 1 / 105 • GO • K 51

Outlet port for heating liquids **

Counterflange: Flange C 15 x 21.3 DIN 2633
approx. Weight (kg)
1/ 55 = 45 kg
BTH
1/105 Z; F = 46 kg
1/ 55 = 48 kg
BTH
1/105 G = 49 kg
** Clockwise or anticlockwise by
choice unused connection is to
be sealed

Parallel key acc. to DIN 6885

Counterflange: Welding flange acc. to B. 009 695 0002

Inlet port for heating liquids

Blank flange B 15 ND 16 DIN 2527 Counterflange: Flange C 15 x 21.3 DIN 2633

(finished) clockwise or anticlockwise by
(finished) choice unused connection is to be sealed

12 KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu
Transfer Gear Pumps BT, BTH

Dimensions

100
BTH 2 / 130 • ZO • K 51

Outlet port for heating liquids **

Parallel key acc. to DIN 6885

Inlet port for heating liquids

Clockwise or anticlockwise by
choice unused connection is to be sealed
100
BTH 2 / 130 • FO • K 51

Outlet port for heating liquids **

Parallel key acc. to DIN 6885

Inlet port for heating liquids

Clockwise or anticlockwise by
choice unused connection is to be sealed
100
BTH 2 / 130 • GO • K 51

Outlet port for heating liquids ** approx. Weight (kg)

Counterflange: Flange C 20 x 26.9 DIN 2633
2/100 = 84 kg
BTH
2/130 Z; F = 85 kg
2/100 = 93 kg
BTH
2/130 G = 94 kg

** Dimensions correspond
to mounting surface of
inlet port for heating liquids

Parallel key acc. to DIN 6885

Counterflange: Flange C 50 x 60.3 DIN 2633 (finished)

Inlet port for heating liquids

Blank flange B 20 ND 16 DIN 2527
Counterflange: Flange C 20 x 26.9 DIN 2633
(finished) (finished) clockwise or anticlockwise by
choice unused connection is to be sealed

KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu 13
 Transfer Gear Pumps BT, BTH

Dimensions

BTH 3 / 150 • ZO • K 51

Outlet port for heating liquids **

Parallel key acc. to DIN 6885

Inlet port for heating liquids

Clockwise or anticlockwise by
choice unused connection is to be sealed

BTH 3 / 150 • FO • K 51

Outlet port for heating liquids **

Parallel key acc. to DIN 6885

Inlet port for heating liquids

Clockwise or anticlockwise by
choice unused connection is to be sealed

BTH 3 / 150 • GO • K 51

Outlet port for heating liquids **

approx. Weight (kg)
Counterflange: Flange C 25 x 33.7 DIN 2633
BTH 3/150 Z; F = 142 kg
BTH 3/150 G = 155 kg

** Dimensions correspond to
mounting surface of
inlet port for heating liquids

Parallel key acc. to DIN 6885

Counterflange: Flange C 80 x 88.9 DIN 2633 (finished)

Inlet port for heating liquids

Blank flange B 25 ND 16 DIN 2527 Counterflange: Flange C 25 x 33.7 DIN 2633

(finished) clockwise or anticlockwise by
(finished) choice unused connection is to be sealed

14 KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu
Transfer Gear Pumps BT, BTH

Dimensions

BT 1... 7 BZ 0CK 59

Shaft end
Pump
R A B C D ØE F G H O J K P Ød l m n u t d1 l1 kg
type

BT 4 G 2 40 80 95 135 10 12 130 131,5 100 102 245 189 24 50 40 5 8 27 M8 19 18,5

BT 6 G 2 35 75 185 225 14 28 175 175 126 106 245 252 24 50 40 5 8 27 M8 19 33,0

Inlet and outlet ports equally sized.

KRACHT GmbH · Gewerbestr. 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209 · mail [email protected] · web www.kracht.eu 15
 Product Portfolio

Transfer Pumps Flow Measurement

Transfer pumps for lubricating oil Gear and turbine flow meters and electronics
supply equipment, low pressure for volume and flow metering technology in
filling and feed systems, dosing and hydraulics, processing and laquering technology.
mixing systems.
Industrial Hydraulics /
Mobile Hydraulics Test Bench Construction
Single and multistage high pressure Cetop directional control and proportional
gear pumps, hydraulic motors and valves, hydraulic cylinders, pressure, quantity
valves for construction machinery, and stop valves for pipe and slab construction,
vehicle-mounted machines. hydraulic accessories for industrial hydraulics
(mobile and stationary use).
Technology Test benches / Fluid Test benches.

BT, BTH / GB / 08.08

KRACHT GmbH · Gewerbestraße 20 · 58791 Werdohl, Germany · fon +49 (0) 23 92 / 935-0 · fax +49 (0) 23 92 / 935 209
mail [email protected] · web www.kracht.eu