2 OUTPUT LED FLASHER MULTI-PATTERN

ETFFC02LED
ELECTRICAL SPECIFICATION
Input Voltage Range +8 Vdc to +30 Vdc
Output Drive Current 3 Amps per Output
Operating Temperature -40 C to +85 C 1/2" off-set from unit centerline
Flash Patterns Inter-Cycle, Warp, Double,
Quad, Quint, E-Pattern, Q-
Switch, Power Pulse, ETM
Output Drive Method High-side switched
Pattern Control Method Wire Matrix (5 wires, 2
head-control, 3-pattern #6 sheet metal screws
control
Standby Current <5mA @ 12.8 Vdc
Reverse Polarity Protection Yes (with inline fuse)
Short Circuit Protection Yes
Thermal Protection Yes
Figure 1.
MECHANICAL SPECIFICATIONS
Weather resistance Potted to protect circuitry, but not
waterproof WARNING
Dimensions 3.2" x 1.45" x 0.85" This Flasher is NOT waterproof!! This unit must
be installed in a location protected from the
environment.

WARNING
This device in intended for use with LED Lights
ONLY!!

Emergency Lighting is intended for use on +8-30Vdc

approved vehicles ONLY. It is the responsibility
10 Amp ATO FUSE
of the user of these systems to insure compliance (user supplied)
to any Federal, State or Municipal regulations RED
which may apply. FLASHER
ORANGE

YELLOW
VIOLET

GREEN

WHITE

Use of this product on an Incandescent, Halogen

BLUE

or any light source other than LED's may damage

the unit and void the warranty. BLACK
LED LED
See Matrix for LIGHT LIGHT
The device is designed to flash any SoundOff Signal LED Light Pattern Selection
up to 3 amps load per output. DO NOT connect more than a
3 amp load to the output. Doing so will shut the unit down to
prevent damage to the Flasher.

Figure 2.
 INSTALLATION Remote LED Lightheads
1. First, install the Flasher in a protected location using the (2 wire installation)
flasher itself as a template. Use #6 sheet metal screws and
note that flasher is designed with 1/2" slot off-set. See figure
#1 on previous page. Make sure all connectors are easily
accessible.

IMPORTANT RED - To Flasher Output

For continued reliability, RTV or waterproofing grease
must be used on all terminals to prevent corrosion BLACK - Ground
and premature failure of the connections
Self Contained LED Lighthead in
Remote Flash Mode (3 wire installation)

2. Install the LED light heads in the preferred locations.

3. Run the cable between each individual light and the

Flasher. Make sure the cable is secure along the chosen
routing inside the vehicle to prevent it from damage by chaf-
ing or binding. Be sure to keep the cable away from engine
hot spots. RED - To Flasher Output

4. Plug the Power / Control Harness into the Flasher. Con- BLACK - Ground
nect the Black wire to a reliable ground. Connect the Red
wire through a 10 Amp AUTO style fuse to +12 Volts.
WHITE - Ground

NOTE
It is important to follow the correct color code when Figure 3.
inserting the pins into the AMP connectors.
PATTERN MATRIX
To select any one of the different Flash Modes, simply con-
nect the attached control wires to a switch in the following
5. Connect the extension cables to the LED light heads.
combinations. Connect the wires marked “X” to (+) 10-16
Vdc and remove the unused wires or connect them to (-)
6. Next, connect the other end of the cable Output on the
ground.
Flasher, see Figure 1.
FPM Violet Orange Green White

OFF
1 QuadTM 70 X
TM
2 Warp 350 X
TM
3 Double 140 X X
TM
4 Quint 70 X
TM
5 Inter-cycle X X
TM
6 Q-Switch X X
TM
7 Power Pulse 180 X X X
TM
9 E Single 130 X X
TM
10 E Single 220 X X
TM
11 E Double 130 X X X
TM
12 E Double 220 X X
TM
13 ETM 180 X X X

WARRANTY
SoundOff Signal warranties the LED Flasher System for Five (5) full years from the date of purchase to the original purchaser against any manufactured defects or workmanship. This warranty applies only to units installed
according to the manufacturer's installation instructions and operated within the unit's specifications. Warranty is void if the unit was installed incorrectly or maliciously damaged. All warranty claims must be accompanied
by a dated proof of purchase. SoundOff Signal retains the right to be the sole mediator of what constitutes defects in performance or manufacturing.
ETFFC02LED 3/05