Scribd
Upload
27 views

Week-6

Uploaded by

Ashok Kumar Rajanavar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
27 views

Week-6

Uploaded by

Ashok Kumar Rajanavar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF or read online on Scribd
You are on page 1/ 4
6) (stpsiswayam gov detaleNPTEL) it | (https://swayam.gov.in) [email protected] NPTEL (https://swayam.gov.in/explorer?ncCode=NPTEL) » Pavement Materials (Under Pavement Engineering) (course) Ifalready reustered cick | Week 6: Assignment 6 to check your payment status “The due date for submitting this assignment has passed Due on 2023-09-06, 23:59 IST. Course Assignment submitted on 2023-09-06, 23:42 IST outline 1) The representation of compliance for a dashpot is equal to 1 point How does an VE NPTEL tn online course. nt work? () E Yes, the answer is correc. Week 0 () Score: 1 Accepted Answers: Week 1 () m wee? 0 2) In anon-linear viscoelastic material, the response to any loading 1 point is a function of Week 3 () Time Time and temperature Week 4 () Time, temperature, amplitude of load Week 5 () Time, temperature, equipment used Yes, the answer is correc. Week 6 () Score: 1 Accepted Answers: @ Lecture 26: Time, temperature, amplitude of load Introduction to 3) Ina rheological model comprising of parallel arrangement of 1 point Viscoelasticty spring and dashpot (unitz unit=71&lesso 1-72) @ Lecture 27: Rheological Properties of Bitumen (Part-1) (unit? unit=71&lesso n=73) @ Lecture 28: Rheological Properties of Bitumen (Part-2) (unit? unit=71&lesso n=74) @ Lecture 29: Grading of Bitumen (Part-1) (unit? unit=718lesso n=75) @ Lecture 30: Grading of Bitumen (Part-2) (unit? unit=71&lesso 1°76) © Quiz: Week 6: Assignment 6 (assessment? name=141) Solution for Week 6 (unit? unit=718lesso n=147) Week 7 () Week 8 () Week 9 () Week 10 () Week 11 () Week 12 () Total strain is the summation of strains in both the elements Total stress is the summation of stress in both the elements Strain in each element is equal Stress in each element is equal No, the answer is incorrect. Score: 0 Accepted Answers: Total stress is the summation of stress in both the elements Strain in each element is equal 4) As per PG grading system, the minimum failure strain ina DTT 1 point test should be 1% 2% 5% 10% No, the answer is incorrect. Score: 0 Accepted Answers: 1% 5) Reduced frequency is equal to 1 point Multiplication of complex modulus and shift factor Multiplication of complex modulus and frequency Multiplication of frequency and shift factor None of the above No, the answer is incorrect. Score: 0 Accepted Answers: Multiplication of frequency and shift factor 6) If a sample of bitumen was tested at a frequency of 1 Hz ata temperature of 60 °C in a DSR. If the value of G* = 0.07 MPa and 5 = 56°, the absolute viscosity will be equal to (in Pa.s). [Round off the answer value to next whole number] 107247 No, the answer is incorrect. Score: 0 Accepted Answers: (Type: Numeric) 58033 O points 7) Cole-Cole plot is the relationship between 1 point Complex modulus and phase angle Complex modulus and storage modulus Complex modulus and frequency Loss modulus and storage modulus DOWNLOAD VIDEOS () WEEKLY FEEDBACK 0 Transcript () Problem Solving Session - July 2023 () No, the answer is incorrect, Score: 0 Accepted Answers: Loss modulus and storage modulus 8) At the cross over frequency 1 point cc G>s’ C= Yes, the answer is correct Score: 1 Accepted Answers: one 8) Penetration ratio is equal to 1 point Penetration at 25 °C / Penetration at 4 °C Penetration at 4 °C / Penetration at 25 °C Penetration at 25 °C (5 seconds) / Penetration at 25 °C (60 seconds) Penetration at 25 °C / Penetration at 15 °C No, the answer is incorrect. Score: 0 Accepted Answers: Penetration at 4 °C / Penetration at 25 °C 10)For a PG 64-12 grade bitumen, what should be the intermediate temperature for testing fatigue characteristic 26 No, the answer is incorrect. Score: 0 Accepted Answers: (Type: Numeric) 30 1 point 11) If the minimum temperature of a project location is -22 °C, thet point BBR test should be done at a temperature of 22°C ATC 12°C “32°C No, the answer is incorrect. Score: 0 Accepted Answers: 12°C

You might also like