Scribd
Upload
772 views3 pages

Lubrizol 16010L - (Api SL, CF) - TDS

LUBRIZOL 16010L

Uploaded by

Pranit More Arabian Petroleum Limited
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
772 views3 pages

Lubrizol 16010L - (Api SL, CF) - TDS

LUBRIZOL 16010L

Uploaded by

Pranit More Arabian Petroleum Limited
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Product | Type

LUBRIZOL® 16010L Passenger Car Motor Oil Additive

A multipurpose additive for API SL/CF crankcase


oils
Application

Recommended for use at: 6.7 % by weight


API SL/CF
JASO MA2 (T903:2011)

JASO MB (T903:2011) WITH A BOOSTER

Testing conducted in SAE 15W-40 also covers SAE 20W-40 and SAE 20W-50.
(API SL also covered in SAE 10W-30).

Physical Characteristics
Minimum Target Maximum
FLASH POINT, C, PMCC 165

LBS PER U.S. GAL @ 15.6 C 8.23

LBS PER IMP GAL @ 15.6 C 9.88

POUR POINT, C -15

SPECIFIC GRAVITY @ 15.6 C 0.968 0.988 1.008

VISCOSITY @ 100 C, CST 170

VISCOSITY @ 40 C, CST 3550

Chemical Characteristics
Minimum % Weight Typical Maximum % Weight
BASE NUMBER (MGKOH/G) 97

CALCIUM 2.55 2.84 3.12

NITROGEN 0.72 0.81 0.89

PHOSPHORUS 1.35 1.50 1.65

SULFATED ASH 12.2

SULFUR 3.6

ZINC 1.49 1.66 1.83

Benefits
LUBRIZOL® 16010L forms part of the Lubrizol 16010 series.

The product allows oil marketers a cost optimised approach in formulating lubricants meeting API
SL/CF.

LUBRIZOL® 16010L can also be obtained as a combination of other products within the Lubrizol 16010
series as follows:
6.7% LUBRIZOL® 16010L = 4.0% Lubrizol 16010 + 2.7% Lubrizol 8696L

6.7% LUBRIZOL® 16010L = 6.45% Lubrizol 16010J + 0.25% Lubrizol 8696


LUBRIZOL® 16010L Unloading, storage and blending instructions
General handling instructions - In general, The Lubrizol Corporation recommends, as a minimum, the use of neoprene or
nitrile rubber gloves and safety glasses or chemical splash goggles. The Material Safety Data Sheet should be consulted for
specific information and for information on health and safety when handling this product
Fire and explosion hazard data
Flash Point (method) Classification
165oC PMCC N/A
Temperature recommendations
Unloading Pumping Temperature 65oC 149oF
Maximum temperature 75oC 167oF
Storage
Maximum temperature for long-term storage 45oC 113oF
Blending
Maximum base oil temperature for mechanical or in-line mixing 75oC 167oF
Equipment recommendations
Type of Pump Positive Displacement
Ball Launched, Insulated,Steam Traced Using 107°C/225°F Steam
Type of transfer line
Max.
Transfer line size 3 inch/8 cm. Min.
Heat source
Type Steam 107°C/225°F Max.
Storage tank Suction Heater Recommended
Viscosity data cSt SUS
at 25°C,77°F 10874 50304
at 40°C, 104°F 3550 16449
at 100°C, 211°F 170 793
Notes
Pour Point -15°C, 6°F

Additional Recommendations
* Holding the material in excess of this temperature may cause chemical degradation. Use steam for heating and tracing only
when the material is in motion to avoid localized overheating. Cold Temperature Storage - If product has been stored below
its pour point temperature it should be heated to 21°C/70°F before using.
Effective: 4/27/2015 9:45:29 AM

You might also like