Conplast RP200* constructive solutions

Retarding water reducing admixture

Uses Technical support

 To improve the effectiveness of the water content of a Fosroc provides a technical advisory service for on-site
concrete mix. assistance and advice on admixture selection, evaluation
trials and dispensing equipment. Technical data and
 To help maintain the workability of ready-mixed concrete guidance can be provided for admixtures and other products
deliveries in hot weather. for use with fresh and hardened concrete.

 To extend working times of concrete.

Dosage
 Particularly suitable for use in mixes with low cohesion.
The optimum dosage of Conplast RP200* to meet specific
requirements should always be determined by trials using the
Advantages
materials and conditions that will be experienced in use. The
normal dosage range is 0.3 to 0.8 litres/100 kg of
 Water reduction significantly improves compressive cementitious material, including PFA, GGBFS or micro-silica.
strengths at all ages and enhances durability.
Use at other dosages
 Controlled retardation extends working life and stiffening
time for ease of construction. Dosages outside the normal rang quoted above can be used
 Control of stiffening improves slip forming and assists in to meet particular mix requirements. Contact Fosroc for
preventing the formation of cold joints in large pours. advice in these cases.

 Minimised transportation delay problems maintains Properties

placeability and reduces the risk of pump blockage.

 Slight air entrainment improves cohesion in mixes with Appearance: Brown liquid
o
poorly graded sands or a lack of fine materials, Specific gravity: Typically 1.060 at 20 C
minimising bleed and segregation. Chloride content: Nil to BS 5075
Air entrainment: Typically less than 2% additional air
 Allows specified strength grades to be met at reduced is entrained at normal dosages.
cement content or increased workability. Alkali content: Typically less than 5.0 g. Na2O
equivalent/litre of admixture. A fact
 Chloride free, safe for use in pre-stressed and reinforced sheet on this subject is available.
concrete.

Instructions for use

Standard compliance
Retardation
Conplast RP200* complies with BS 5075 Part 1 and with
ASTM C494 as Type B and Type D.
The level of retardation obtained may be varied by altering
the dosage of Conplast RP200* used, which will also alter
Description the level of water reduction obtained. Retardation is also
affected by factors other than the admixtures, depending on
Conplast RP200* is a chloride free water reducing admixture the mix details and conditions involved. Major factors include
based on selected lingosulphonate materials. It is supplied the following:
as a brown solution which instantly disperses in water.
a) Cement replacement materials will usually give
Conplast RP200* disperses the fine particles in the concrete greater levels of retardation than concrete mixes
mix, enabling the water content of the concrete to perform made with ordinary Portland cement at the same
more effectively. The initial hydration of the cement is also admixture dosage.
delayed, resulting in a delay in the setting time of the
concrete with no adverse effect on subsequent stiffening and b) High temperatures will require increased
strength gain. dosages to obtain the same change in
stiffening time compared to a control mix.

Page 1
Conplast RP200*
c) Changes in cement content, source or chemistry Storage
may lead to variations in the retardation obtained.
The amount of tri-calcium aluminate in the cement Conplast RP200* has a minimum shelf life of 12 months
has been identified as being one of the main o
provided the temperature is kept within the range of 2 C to
contributory factors in this respect, with a lower o
50 C. Should the temperature of the product fall outside this
level leading to greater retardation. range contact Fosroc for advice.

Compatibility Freezing point:

o
Approximately -4 C

Conplast RP200* is compatible with other Fosroc admixtures

used in the same concrete mix. All admixtures should be Precautions
added to the concrete separately and must not be mixed
together prior to addition. The resultant properties of Health and safety
concrete containing more than one admixture should be
assessed by trial mixes. Conplast RP200* does not fall into the hazard classifications
of current regulations (see notes 1 and 2 below). However, it
Conplast RP200* is suitable for use with all types of ordinary should not be swallowed or allowed to come into contact with
Portland cements and cement replacement materials such as skin and eyes.
PFA, GGBFS and micro-silica.
Suitable protective gloves and goggles should be worn.
Dispensing
Splashes on the skin should be removed with water. in case
The correct quantity of Conplast RP200* should be measured of contact with eyes rinse immediately with plenty of water
by means of a recommended dispenser. The admixture and seek medical advice. If swallowed seek medical
should then be added to the concrete with the mixing water to attention immediately. Do not induce vomiting.
obtain the best results. Contact Fosroc for advice regarding
suitable equipment and its installation. For further information consult the Material Safety Data Sheet
available for this product.
Effects of overdosing
Fire
An overdose above the normal range of Conplast RP200* will
result in a significant increase in retardation as compared to Conplast RP200* is water based and non-flammable.
that normally obtained at the intended dosage. Provided that
adequate curing is maintained, the ultimate strength of the Cleaning and disposal
concrete will not be impaired by increased retardation and
will generally be increased. The effects of overdosing will be Spillages of Conplast RP200* should be absorbed onto
further increased if sulphate resisting cement or cement sand, earth or vermiculite and transferred to suitable
replacement materials are used. containers. Remnants should be nosed down with large
quantities of water.
Over-dosage may also cause increased air entrainment
which will tend to reduce strength. The degree of this effect The disposal of excess or waste material should be carried
will depend on the particular mix design and overdose level. out in accordance with local legislation under the guidance of
the local waste regulatory authority.
Estimating - packaging Note 1: CPL Regulations 1984 Supply-Schedule 1.
Note 2: HSE publication Guidance Note EH40.
Conplast RP200* is available in drum or bulk supply. For
larger users, storage tanks can be supplied.

Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.

Fosam Company Limited

Telephone: +966 2 637 5345 Fax: +966 2 637 5891 email: [email protected]
Head Office
Post Box 11081 Regional Offices
Jeddah Sales Office Tel: (02) 608 0999 Fax: (02) 638 0693 Yanbu Tel: (04) 322 4280 Fax: (04) 391 2980
Jeddah - 21453 Jeddah Showroom Tel: (02) 665 0187 Fax: (02) 667 4844 Makkah Tel: (02) 542 0869 Fax: (02) 542 0869
Saudi Arabia Riyadh Tel: (01) 482 9303 Fax: (01) 482 7562 Medinah Tel: (04) 855 0091 Fax: (04) 855 0047
Dammam Tel: (03) 814 1282 Fax: (03) 814 1581 Jubail Tel: (03) 362 3904 Fax: (03) 362 3875

www.fosroc.com
Khamis Mushayt Tel: (07) 250 0469 Fax: (07) 250 0469 CSD Tel: (02) 608 0999 Fax: (02) 638 0693

Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 2 FO SA/CONPLAST RP200*/08/09