6C-WDM-0240BD

6COM,BIDI SFP, 1.25 Gb/s,1550nm,SMF,40km,DDM,LC connector, 0°C to +70°C

FEATURES
 Dual data-rate of 1.25Gbps/1.063Gbps operation
 1550nm DFB laser and PIN photodetector for 40km transmission
 Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
 Digital Diagnostic Monitoring:
Internal Calibration or External Calibration
 Compatible with SONET OC-24-LR-1
 Compatible with RoHS
 +3.3V single power supply
 Operating case temperature:
 Standard: 0 to +70°C
 Extended: -40 to +85°C

APPLICATIONS
 Gigabit Ethernet
 Fiber Channel
 Switch to Switch interface
 Switched backplane applications
 Router/Server interface
 Other optical transmission systems

DESCRIPTION
The SFP-BIDI transceivers are high performance, cost effective modules supporting dual data-rate of
1.25Gbps/1.0625Gbps and 40km transmission distance with SMF.

The transceiver consists of three sections: a DFB laser transmitter, a PIN photodiode integrated with a
trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety
requirements.

The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further
information, please refer to SFP MSA.

SHENZHEN 6COM TECHNOLOGY CO., LTD 1/7

Tel: +86-0755-85293396 E-mail: [email protected]
Web: www.6comgiga.com
 TD+/-
TxFault LD Driver LD
TxDis

LOS
Post Amp PIN+TIA
RD+/-

Vcc
SCL MCU
SDA EEPROM ADC/DAC Temp

1. Absolute Maximum Ratings

Table 1 - Absolute Maximum Ratings
Parameter Symbol Min Max Unit
Supply Voltage Vcc -0.5 4.5 V
Storage Temperature Ts -40 +85 °C
Operating Humidity - 5 85 %

2. Recommended Operating Conditions

Table 2 - Recommended Operating Conditions
Parameter Symbol Min Typical Max Unit
Standard 0 +70 °C
Operating Case Temperature Tc
Industrial -40 +85 °C
Power Supply Voltage Vcc 3.13 3.3 3.47 V
Power Supply Current Icc 300 mA
Data Rate 1250 Mbps

3. Optical and Electrical Characteristics

Table 3 - Optical and Electrical Characteristics
Parameter Symbol Min Typical Max Unit Notes
Transmitter
Centre Wavelength λc 1480 1550 1580 nm
Spectral Width (RMS) ∆λ 1 nm
Side Mode Suppression Ratio SMSR 30 dB
Average Output Power Pout -5 0 dBm 1
Extinction Ratio ER 9 dB

SHENZHEN 6COM TECHNOLOGY CO., LTD 2/7

Tel: +86-0755-85293396 E-mail: [email protected]
Web: www.6comgiga.com
 Optical Rise/Fall Time
tr/tf 0.26 ns
(20%~80%)
Data Input Swing Differential VIN 400 1800 mV 2
Input Differential Impedance ZIN 90 100 110 Ω
Disable 2.0 Vcc V
TX Disable
Enable 0 0.8 V
Fault 2.0 Vcc V
TX Fault
Normal 0 0.8 V
Receiver
Centre Wavelength λc 1260 1310 1360 nm
Receiver Sensitivity -23 dBm 3
Receiver Overload -3 dBm 3
LOS De-Assert LOSD -24 dBm
LOS Assert LOSA -30 dBm
LOS Hysteresis 1 4 dB
Data Output Swing Differential Vout 400 1800 mV 4
High 2.0 Vcc V
LOS
Low 0.8 V
Notes:
1. The optical power is launched into SMF.
2. PECL input, internally AC-coupled and terminated.
3. Measured with a PRBS 27-1 test pattern @1250Mbps, BER ≤1×10-12.
4. Internally AC-coupled.

4. Timing and Electrical

Table 4 - Timing and Electrical
Parameter Symbol Min Typical Max Unit
Tx Disable Negate Time t_on 1 ms
Tx Disable Assert Time t_off 10 µs
Time To Initialize, including Reset of Tx Fault t_init 300 ms
Tx Fault Assert Time t_fault 100 µs
Tx Disable To Reset t_reset 10 µs
LOS Assert Time t_loss_on 100 µs
LOS De-assert Time t_loss_off 100 µs
Serial ID Clock Rate f_serial_clock 400 KHz
MOD_DEF (0:2)-High VH 2 Vcc V
MOD_DEF (0:2)-Low VL 0.8 V

5. Diagnostics
Table 5 – Diagnostics Specification
Parameter Range Unit Accuracy Calibration
Temperature 0 to +70 °C ±3°C Internal / External
Voltage 3.0 to 3.6 V ±3% Internal / External
Bias Current 0 to 100 mA ±10% Internal / External
TX Power -5 to 0 dBm ±3dB Internal / External
RX Power -23 to -3 dBm ±3dB Internal / External

SHENZHEN 6COM TECHNOLOGY CO., LTD 3/7

Tel: +86-0755-85293396 E-mail: [email protected]
Web: www.6comgiga.com
Digital Diagnostic Memory Map
The transceivers provide serial ID memory contents and diagnostic information about the present operating
conditions by the 2-wire serial interface (SCL, SDA).

The diagnostic information with internal calibration or external calibration all are implemented, including
received power monitoring, transmitted power monitoring, bias current monitoring, supply voltage
monitoring and temperature monitoring.

The digital diagnostic memory map specific data field defines as following.

SHENZHEN 6COM TECHNOLOGY CO., LTD 4/7

Tel: +86-0755-85293396 E-mail: [email protected]
Web: www.6comgiga.com
6. Pin Definitions
Pin Diagram

Pin Descriptions
Pin Signal Name Description Plug Seq. Notes
1 VEET Transmitter Ground 1
2 TX FAULT Transmitter Fault Indication 3 Note 1
3 TX DISABLE Transmitter Disable 3 Note 2
4 MOD_DEF(2) SDA Serial Data Signal 3 Note 3
5 MOD_DEF(1) SCL Serial Clock Signal 3 Note 3
6 MOD_DEF(0) TTL Low 3 Note 3
7 Rate Select Not Connected 3
8 LOS Loss of Signal 3 Note 4
9 VEER Receiver ground 1
10 VEER Receiver ground 1
11 VEER Receiver ground 1
12 RD- Inv. Received Data Out 3 Note 5
13 RD+ Received Data Out 3 Note 5
14 VEER Receiver ground 1
15 VCCR Receiver Power Supply 2
16 VCCT Transmitter Power Supply 2
17 VEET Transmitter Ground 1
18 TD+ Transmit Data In 3 Note 6
19 TD- Inv. Transmit Data In 3 Note 6

SHENZHEN 6COM TECHNOLOGY CO., LTD 5/7

Tel: +86-0755-85293396 E-mail: [email protected]
Web: www.6comgiga.com
 20 VEET Transmitter Ground 1
Notes:
Plug Seq.: Pin engagement sequence during hot plugging.
1) TX Fault is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor on the host
board to a voltage between 2.0V and Vcc+0.3V. Logic 0 indicates normal operation; Logic 1 indicates a
laser fault of some kind. In the low state, the output will be pulled to less than 0.8V.
2) TX Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the
module with a 4.7k~10kΩ resistor. Its states are:
Low (0 to 0.8V): Transmitter on
(>0.8V, < 2.0V): Undefined
High (2.0 to 3.465V): Transmitter Disabled
Open: Transmitter Disabled
3) Mod-Def 0,1,2. These are the module definition pins. They should be pulled up with a 4.7k~10kΩ resistor
on the host board. The pull-up voltage shall be VccT or VccR.
Mod-Def 0 is grounded by the module to indicate that the module is present
Mod-Def 1 is the clock line of two wire serial interface for serial ID
Mod-Def 2 is the data line of two wire serial interface for serial ID
4) LOS is an open collector output, which should be pulled up with a 4.7k~10kΩ resistor. Pull up voltage
between 2.0V and Vcc+0.3V. Logic 1 indicates loss of signal; Logic 0 indicates normal operation. In the
low state, the output will be pulled to less than 0.8V.
5) RD-/+: These are the differential receiver outputs. They are internally AC-coupled 100 differential lines
which should be terminated with 100Ω (differential) at the user SERDES.
6) TD-/+: These are the differential transmitter inputs. They are internally AC-coupled, differential lines with
100Ω differential termination inside the module.

7. Recommended Interface Circuit

SHENZHEN 6COM TECHNOLOGY CO., LTD 6/7

Tel: +86-0755-85293396 E-mail: [email protected]
Web: www.6comgiga.com
8. Mechanical Dimensions

9. Ordering information
Part Number Product Description
6C-WDM-0240BD BIDI SFP, 1.25 Gb/s,1550nm,SMF,40km,DDM,LC connector, 0°C to +70°C
6C-WDM-0240BID BIDI SFP, 1.25 Gb/s,1550nm,SMF,40km,DDM,LC connector, -40°C to +85°C

SHENZHEN 6COM TECHNOLOGY CO., LTD 7/7

Tel: +86-0755-85293396 E-mail: [email protected]
Web: www.6comgiga.com