B.

Tech Semester III

Subject Code: EC2002 Course Title Digital Electronics and Microprocessor

Contact Hours L-3, T-0, L-2, Interfacing
Programme B.Tech Credit 4
Pre-requisites NIL Semester III
Evaluation scheme Quiz I (10%), Mid term (25%), Quiz II (10%), End term (35%), Lab (20%)
Learning Objective: To impart basic knowledge of analysis and design of various digital electronics
circuits and knowledge on Microprocessors and Microcontroller to solve real world problems in an
efficient manner.
Course Detail :
Module 1: Number Systems and Boolean Algebra, Simplification of functions using Karnaugh map and
Quine McCluskey Method, Boolean Function Implementation, Minimization and Combinational Design,
Examples of Combinational Digital Circuits, Hazards in Combinational Circuits, Hazard free realization.
[10H]
Module 2: Introduction to Sequential circuits: Latches and Flip-Flops (RS, JK, D, T and Master Slave), Design
of a Clocked Flip-Flop, Flip-Flop conversion, Practical Clocking aspects concerning Flip-Flops. Counters:
Design of Single Mode and Multimode Counters, Ripple Counters, Synchronous Counters, Shift Registers,
Shift Register Counters and Random Sequence Generators. [12H]
Module 3: Introduction to Microprocessors: The 8085 microprocessor architecture, Programmer's
model, Instruction set, instruction Format, Addressing modes, Machine cycle, Timing diagrams, and
memory map, interfacing memory and I/O devices, The 8085 assembly language programming, Looping,
block transfer, bit manipulation, time delay routines, stack and subroutine, I /O programming, interrupt
handling. [12H]
Module 4: Interfacing of 8085: Handling of I/O ports and port programming using IN/OUT instruction,
STACK handling and Signed Number Arithmetic, Interfacing instructions and control word structure for
various pins like 8255, 8155, 8279,8259, etc. [08H]
Text/Reference books:
1. Digital Design by M Morris Mano and Michael D Ciletti, Pearson Prentice Hall, 4 th Edition.
2. Digital Logic Circuit Analysis and Design by - Victor P. Nelson, H. Troy Nagle, J. David Irwin & Bill D.
Carrol, Prentice Hall.
3. Microprocessor Architecture, Programming, and Applications with the 8085 by Ramesh Gaonkar,
Penram International Publishing; 6th edition.
4. Microprocessors and interfacing by Douglas Hall, McGraw Hill Education; 3rd edition.
 Subject Code: EC203a Course Title Principle of Analog
Communications
Contact Hours L-2, T-0, L-2 Credit 2
Programme B.Tech Semester III
Pre-requisites NIL
Evaluation scheme Evaluation-I: 50%, Evaluation-II 50%
Learning Objective: In this course undergraduate students will learn about the signal, system, modulation
and transmission of signal using different techniques such as amplitude and angle modulation.
Course Detail :
Introduction to Communication Systems and review of signal & system: Communication network
and channel, Difference between Analog and Digital type of signal and Communication, Classification of
Signals and systems, Fourier series, Fourier transform and its Properties and examples, Impulse Response,
and Transfer Function.
Amplitude Modulation: General amplitude Modulation, Double Sideband (DSB) Modulation, Single-
Sideband and Vestigial-Sideband Modulations. Implementation and generation techniques of AM
Modulators and demodulators.
Angle Modulation: Basic definition, Phase modulation, frequency modulation, relationship between
frequency and phase modulation, bandwidth of power and spectrum of FM signal, Narrowband and
wideband frequency modulation, Transmission bandwidth of FM signal, Generation and detection
techniques of angle modulation.
Text books:
1. Haykin, S., “Communication System”, Fourth Edition, Wiley and Sons, 2005.
2. Lathi, B.P., “Modern Digital and Analog Communication System”, Oxford University Press, 2006.
Reference books:
1. John G. Proakis and Masoud Salehi, “Communication System Engineering”, Prentice Hall,2006.
2. Taub and Schilling, “Principles of Communication System”, Tata McGraw-Hill, 1991.

Subject Code: EC203b Course Title Network Theory (Analysis and

Contact Hours L-2, T-0, P-0 Synthesis)
Programme B.Tech Credit 2
Pre-requisites Fundamentals of Electrical Semester III
Engineering
Evaluation scheme Quiz Exam (40%), Assignment (10%), End-Term (50%)
Learning Objective:
• To make the students capable of analyzing any given electrical network.
• To make the students learn how to synthesize an electrical network from a given impedance/
admittance function.
• To develop hierarchical thinking to see more complex systems as a generalization of simple circuits
and techniques.
realness, properties of positive real functions, synthesis of R-L, R-C, and L-C driving point functions, Foster
and Cauer forms, introduction to two-port network synthesis, and basics of filter design. [06H]
Text/Reference books:
1. M.E. Van Valkenburg, Network Analysis, Prentice-Hall, 2006.
2. M.E. Van Valkenburg, Network Synthesis, Prentice Hall, 2007.
3. F. F. Kuo, Network Analysis and Synthesis, John Wiley and Sons, 1966.
4. S.Seshu and M.B. Reed, Linear Graphs and Electrical Networks, Addison Wesley, 1961.
5. N. Balabanian and T.A. Bickart, Linear Network Theory: Analysis, Properties, Design and Synthesis,
Matrix Publishers, Inc. 1981.
6. L.O. Chua, C.A. Desoer, E.S. Kuh, Linear and Nonlinear Circuits, McGraw Hill, 1987.
7. W. H. Hayt Jr., J.E. Kemmerly, Engineering Circuit Analysis, McGraw-Hill, 1971.
8. J. A. Edminister, and M. Maqvi, Theory and Problems of Electric Circuits, Schaum's Outline Series, TMH.
Course Detail :
Introduction: Network elements, formulation of network equation, network representations, Transient
analysis in RL, RC, and RLC networks with DC and AC excitation, response to step, impulse and ramp
inputs, coupled circuits: self-inductance and mutual inductance, coefficient of coupling, and dot
convention. [09H]
Two-Port Networks: Characteristics of linear time-invariant networks, network parameters (short circuit
admittance parameters, open circuit impedance parameters, transmission parameters, image
parameters, and hybrid parameters), interconnections of networks (tee and pie circuit representation,
cascade, and parallel connections). [08H]
Graph theory: Network graphs, tree, branches, chords, fundamental cut-sets and loops, incidence, tie-
set, cut-set matrices, and their applications in network analysis. [05H]
Network Synthesis: Positive real function, physical realizability conditions, Hurwitz property, positive
 Subject Code: EC204a Course Title Electronics Devices and Circuits
Contact Hours L-2, T-0, P-0 Credit 2
Programme B.Tech Semester III
Pre-requisites NIL
Evaluation scheme Quiz I (10%), Mid term (20%), Quiz II (10%), End term (40%), lab (20%)
Review of theory of semiconductor, PN junction diode theory, contact potential and current components,
energy band diagram for PN Junction, Diode I-V Characteristics, breakdown voltage and leakage current
Diode applications rectifier half wave and full wave with filter design, clipping and clamping circuit
analysis and design, Special purpose diodes zener diode and its application for regulator, varactor diode,
PIN diode, tunnel diode, photodiode, Schottkey barrier diode and LED. [10H]
Junction field effect transistor (JFET), device structure and physical operation, IV characteristics, n-
channel and p-channel JFET, Biasing and small signal analysis and JEFT applications as voltage amplifier.
MOSFET basics, the inversion cannel formation, the derivation of the IV characterises, triode region and
saturation region operation, body effect and channel length modulation, Modeling of the MOSFET,
Basing, Common source, common drain, and common gate configurations. MOSFET as an amplifier and
as a Switch, Single stage MOS Amplifier, MOSFET small signal model for analysis of single stage amplifier,
high frequency MOSFET model and frequency response, Current mirror, differential amplifier using
MOSFET. [15H]
Operation of BJT, Current Components, currents gains α and β, BJT Biasing and Q point & Regions of
Operation, Bias Stability, Transistor in CB, CE, CC configuration, Transistor leakage current ICBO and ICEO
and breakdowns.Introduction to amplifiers, RC Coupled amplifiers, frequency response, Transistor re
Model, Transistor H parameter, BJT Small Signal Analysis, BJT and FET High frequency modelling,
Transistor as a switch and power dissipation in the transistor. [10H]
Feedback Amplifiers, Oscillators (Different types), Differential Amplifiers, power amplifier, Operational
Amplifiers and its Applications. Logic Families using BJT and MOSFET for Digital Applications. [07H]
Laboratory Experiments
1. Introduction to laboratory equipment
2. Clipping and Clamping Circuits Design and analysis
3. Rectifier full wave with filter design
4. Zerner regulator design and analysis
5. JFET characteristics and Baising
6. BJT as switch performance and measurments and verification by simulations tools (pSpice)
7. RC coupled amplifier design and analysis small sigal and high frequency Lab and pSpice
8. MOSFET characterstics and various baising
9. Single stage MOS Amplifier CS, CD and CG and Cascode stages
10. Current mirror using BJT and MOSFET
Text/Reference books:
1. Electronic Circuits Analysis and Design, Donald Neamen.
2. Microelectronics Circuits 5th Edition BySedra and Smith Oxford Publication
3. Electronic Devices and Circuits David A Bell. Oxford Publication
4. Integrated Electronics: Analog and Digital Circuits and Systems, Millman Jacob and Halkias,
Christos C. ,McGraw Hill 2004
5. Electronics Device and Circuit TheoryBoylestad,Robert L. and NashelskyLouis,Ninth Edition, Printice
Hall of India 2005

Subject Code: EC204b Course Title Instrumentation and Measurement

Contact Hours L-2, T-0, P-0 Credit 2
Programme B.Tech Semester III
Pre-requisites NIL
Evaluation scheme Quiz I (10%), Mid term (20%), Quiz II (10%), End term (40%), lab (20%)
Course Detail:
Basic terminologies (range, span, settling time dead zone, input impedance), Static and Dynamic
characteristics, first order and second order instruments with step, ramp and sinusoidal input, output
characteristics. [05H]
Strain gauge, derivation of gauge factor, strain gauge rosette, unbalanced wheatstone bridge, AC bridges
for capacitance, inductance, phase and frequency measurement. Ultrasonic and its applications for
measurement of flow, displacement and non-destructive testing. [05H]
LVDT, phase compensation, phase sensitive demodulation, thermistor and its linearization, RTD, its
construction, three wire and four wire method Muller bridge, Thermocouple, their relative comparison,
cold junction compensation using AD590, grounded thermocouple, potentiometer as displacement
sensor, Capacitance as displacement and level transducer, push pull arrangement, Pressure transducer
[Bourdon gauge, diaphragm gauge (metal and semiconductor) etc]. [08H]
Signal Conditioning Circuits, Quantization, Resolution, Sample and Hold Circuits, Analog (Successive
Approximation, Ramp, and Flash) and Digital (R-2R, Binary weighted) Converters. [04H]
Text/Reference books:
1. Measurement Systems Application and Design, Ernest O. Doebelin, McGraw-Hill
2. Principles of Industrial Instrumentation,2e. Front Cover. Patranabis. Tata McGraw-Hill
3. Clarence W de Silva, MECHATRONICS - An Integrated Approach, CRC Press
4. Alan S Morris, Measurement and Instrumentation Principles, Butterworth-Heinemann
Subject Code: IT2E01 Course Title Matlab and Simulink, Pspice
Contact Hours L-0, T-0, P-2 Credit 2
Programme B.Tech Semester III
Pre-requisites NIL
Evaluation scheme Lab Assignments (20%), Quiz (20%) End-Term (60%)
Learning Objective: Learning the software tools MATLAB, Simulink and Pspice for solving and applying on
electronic circuits.
Course Detail :
MATLAB
Introduction of MATLAB,
Basic Operation of Differentiation, Integration, Linear Equations, matrix operations to solve system of
linear equations, Convolution with practical application
Plotting Functions: Plot subplot, Histogram, bar chart, curve fitting
Logical Operators and Functions, Graphical User Interface
Signals processing tool box, Impulse, step, and response of LTI systems.
Fourier transform and Laplace Transform
Simulink
Building simple Simulink simulations.
Running Simulink simulation to predict a system's behaviour.
PSpice
Introduction to PSpice and components, Simple Dependent Sources, Transient Analysis, Steady State AC
Analysis with the transistor, Simulation of Transistor as an amplifier in CE,CB and CC mode, Frequency
Response, Special Sources, Pulse Sources, SIN Sources, Voltage & Current Controlled Switches, Sub-
circuits with Op-amp examples with PSpice,
Text/Reference books:
 OE1 Choose any one course from below electives

Subject Code: OE2E02 Course Title Probability and Random Processes

Contact Hours L-0, T-0, P-0 Credit 3
Programme B.Tech/B.Des Semester III
Pre-requisites NIL
Evaluation scheme 10 % (Quiz 1), 20% Mid Sem, 10 % (Quiz 2), 40% End Sem, 20% Project
Learning Objective: Basics of probability to design and study probabilistic models
Course Detail :
Introduction to probability: mathematical background - sets, set operations, sigma and Borel fields;
classical, relative-frequency and axiomatic definitions of probability; conditional probability,
independence, total probability, Bayes’ rule; repeated trials; random variables: cumulative distribution
function, continuous, discrete and mixed random variables, probability mass function, probability density
functions. [10H]
Functions of a random variable; expectation - mean, variance and moments; characteristic and moment-
generating functions; Chebyshev, Markov and Chernoff bounds; special random variables-Bernoulli,
binomial, Poisson, uniform, Gaussian and Rayleigh; joint distribution and density functions; Bayes’ rule for
continuous and mixed random variables; joint moments, conditional expectation. [10H]
Covariance and correlation- independent, uncorrelated and orthogonal random variables; function of two
random variables; sum of two independent random variables; random vector- mean vector and
covariance matrix, multivariate Gaussian distribution; sequence of random variables: almost sure and
mean-square convergences, convergences in probability and in distribution, laws of large numbers,
central limit theorem; elements of estimation theory- linear minimum mean-square error and
orthogonality principle. [10H]
Random process: discrete and continuous time processes; probabilistic structure of a random process;
mean, autocorrelation and autocovariance functions; stationarity- strict-sense stationary and wide-sense
stationary (WSS) processes: autocorrelation and cross-correlation functions; time averages and
ergodicity; spectral representation of a real WSS process-power spectral density, cross-power spectral
density, linear time-invariant systems with WSS process as an input- time and frequency domain analyses;
spectral factorization theorem; examples of random processes: white noise, Gaussian, Poisson and
Markov processes. [10H]
Text books:
1. Probability & Random Processes by Grimmett & Stirzaker Fourth Edition, 2018.
2. Adventures in Stochastic Processes by Resnick Springer, 2013.
Reference books:
1. An Introduction to Stochastic Modeling by Taylor and Karlin, third edition Academic Press, 2011.