Scribd
Upload
248 views

EST3 To EST4 Forward Migration SINGLE

This document provides information about upgrading an existing EST3 fire alarm system to an EST4 system, including which EST3 components can be reused and which new components need to be installed. Potential reusable EST3 components include the battery distribution bus, initiating module, signature driver controller, and chassis assembly. New components that would need to be installed include the central processing unit, LCD display, ground fault detection module, enclosure, and filler plate. This is an example of upgrading a standalone EST3 system in a single story warehouse to an EST4 system while reusing the inner and outer cabinet doors.

Uploaded by

Dhaval Chitara
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
248 views

EST3 To EST4 Forward Migration SINGLE

This document provides information about upgrading an existing EST3 fire alarm system to an EST4 system, including which EST3 components can be reused and which new components need to be installed. Potential reusable EST3 components include the battery distribution bus, initiating module, signature driver controller, and chassis assembly. New components that would need to be installed include the central processing unit, LCD display, ground fault detection module, enclosure, and filler plate. This is an example of upgrading a standalone EST3 system in a single story warehouse to an EST4 system while reusing the inner and outer cabinet doors.

Uploaded by

Dhaval Chitara
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

EST3 WITHOUT AUDIO CONTROL

UPGRADE TO EST4

EST3 Uses existing 3-CAB7B wall box with the EST4


new components listed below.

POTENTIAL REUSABLE EST3 COMPONENTS NEW COMPONENTS

Central Processing Unit


Battery Distribution Bus Initiating Module Signature Driver Controller City Tie Module 4-CPU
3-BTSEN 3-IDC8/4 3-SDDC1, 3-SSDC1 CTM
3-SDDC2, 3-SSDC2 LCD Display
Chassis Assembly Display Rail Module Ground Fault Detection 4-3LCD
3-CHAS7 Tamper Switches Module
3-LDSM
3-TAMP GFD
Wallbox
Modem Dialer (DACT) 3-TAMPRCC
3-CAB5(R) Enclosure
3-MODCOM(P)
3-CAB7B LED Display Switches MFC-A
3-CAB14B Signal Module 3-12/S1GY, 3-12/S1RY,
Filler Plate
3-CAB21B 3-OPS 3-12/S2Y, 3-12RY, 3-12SG,
3-LRM This example is a
Power Supply 3-12SR, 3-24G, 3-24R, 3-24Y,
Cabinet Door
3-PPS/M 3-4/3SGYWR, 3-6/3S1G2Y, standalone EST3
3-CAB7(R)
3-CAB14D(R) 4-PPS/M 3-6/3S1GYR system in a single
3-CAB21D(R) 3-BBC/M Battery Cabinet story warehouse,
3-BPS/M BC-1(R) reusing the inner and
Graphic Cards
Cabinet outer cabinet doors.
3-EVDVRA Coder
3-EVPWRA 3-RCC7R CDR-3
3-RCC14R
3-RCC21R

DISCLAIMER: Unique installations may cause variances.


1. Check the detailed technical migration guide, P/N 3102305-EN • REV 005 • ISS 14JAN22, to identify the earliest firmware version supported.
2. Only signature detectors are backward compatible with EST4.
3. The 3-SDU cannot be used to program an EST4 system. To program your new EST4 system, you must use the 4-CU configuration utility.

You might also like