5.

Electricity & Magnetism

 MERGEFOR

5. Electricity and Magnetism

5.0.1 Electricity
Electricity is the flow of charge and it is one of the basic forms of energy. It is associated with
electric charge, a property of atomic particles such as electrons and protons. Electric charges can
be stationary or moving. The effect of static charge which is confined in a body is called static
electricity. The effect of moving charge when it moves through a conductor is called current
electricity. Electricity can be generated from many different sources. It can be sent almost
instantly over long distances and can also be stored. Moreover, it can be converted efficiently
into other forms of energy. Because of this versatility, electricity is an integral part of our
modern life. To know the electricity at first we need to know about charges.

5.0.2 Charge
Charge is a fundamental and characteristic property of the elementary particle which makes up
matter. This property creates a force on one another. These properties are mainly electrons and
protons.
There are two types of electric charges: positive and negative. Positively charged substances are
repelled from other positively charged substances, but attracted to negatively charged substances;
negatively charged substances are repelled from negative and attracted to positive. An object is
negatively charged if it has an excess of electrons, and is otherwise positively charged or
uncharged. The SI derived unit of electric charge is the coulomb (C). The charge on a proton is e
= 1.60218×10-19 C and charge on an electron –e =- 1.60218×10 -19 C.

5.0.3 Point Charge

When the size of the charge body is extremely small then the charged body is called point
charge.

5.0.4 Coulomb
A coulomb is defined as the amount of charge that flows through a given cross-section of a wire
in one second if there is a steady current of one ampere in the wire. Symbolically, it is denoted
by C.
 MERGEFOR

5.0.5 Conservation of Charge

Conservation of charge means the total net charge of any isolated system is constant.
When a glass rod is rubbed with silk, a positive charge appears on the rod and a
negative charge of equal magnitude appears on the silk. So that rubbing does not create
charge but merely transfers charge from one object to another, disturbing slightly by the
electrical neutrality of each. In other words, no new charge is created or destroyed but
slightly transferred. The net charge before and after rubbing is same. So, the
conservation rule is satisfied and we say that charge is conserved.
Unit of Charge is Coulomb and normally it is denoted by C.
An example of charge conservation is “radioactive decay”, such as

238 → Th 234+ He4

92U 92 2

Thus, we see that amount of charge (92e) present before disintegration is the same as that present
after disintegration.

5.0.6 Quantization of Charge

Quantization of charge means the flow of charge in a conductor is not continuous but it is made
up of integral multiples of a certain minimum electric charge. The minimum amount of charge is
denoted by e, the electronic electron charge, has the magnitude 1.6×10 -19 Coul. Any physically
existing charge in the universe, is an integer multiple of e, i.e. ne, irrespective of its origin.
Experimentally it is established that all free charges are integral multiples of a basic unit of
charge denoted by e. Thus q on a body is always given by, q = n e
Where, n (1, 2, 3 ……) is any integer, positive or negative. This basic unit of charge is the
charge that an electron or proton carries. By convention, the charge on an electron is taken to be
negative; therefore charge on an electron is written as –e and that on a proton as +e. So that the
charge exists in discrete packets rather than in continuous amount. This is referred as charge
quantization.

5.1 Coulomb's law or Coulomb's inverse-square law

In 1785 French physicist Charles Augustine de Coulomb established a law of force
exerted by a point charge on the other. It is known as Coulomb’s law.
 MERGEFOR

5.1.1 Coulomb's law

“The force between two point charges at rest is directly proportional to the the magnitude of the
two charge and inversely proportional to the square of the distance between them.”
The force acts along the straight line joining the two charges.
If the two charges have the same sign, the electrostatic force between them is repulsive; if they
have different sign, the force between them is attractive.

Let us consider, two point charges q1 and q2 separated from a distance d. According to
Coulomb’s law

F ∝

F= k
Where, K is a proportional constant.

K=

Finally,
K=

Where, 𝜀 o is the permittivity of the free space and 𝜀 o = 8.854×10-12 C2/Nm2

And

K= = 9×10 9 N m2/C2
 MERGEFOR

5.1.2 Vector form of Coulomb’s law:

Since the active force between two charges is a vector quantity the Coulomb’s law may be
expressed in vector form, the Coulomb’s law is expressed as,

1 𝑞 𝑞
𝐹⃗ = . .ɳ
4𝜋𝜖 𝑑

Where, ɳ is a unit vector along the straight line joining the two charges. The direction of ɳ is
along the direction of 𝐹⃗.
⃗
Now, ɳ=

𝑑⃗ 1 𝑞 𝑞
∴ 𝐹⃗ = ɳ. 𝐹 = 𝐹= . . 𝑑⃗
𝑑 4𝜋𝜖 𝑑

5.1.3 Scope of Coulombs Law:

Despite many arguments, there are many reasons for confidence in Coulomb`s law, over the
wide range from 10-13 cm to many kilometers. This law when incorporated into structure of
quantum physics, correctly describes,

a) The electric forces that bind the electron of an atom to its nucleus

b) The force that bind atoms together to form molecules

c) The forces that binds atoms or molecules to form solids or liquids.

Hence, we can say that most of the forces, except gravitational, are electrical.

5.1.4 Limitations of Coulomb’s Law

The coulomb’s law fails to explain the stability of the nucleus, since, in a nucleus there are
several protons, all having the positive charge. According to Coulomb’s law they should repel
each other. But actually, they do not push themselves apart because nucleus has a stable identity.
Hence, here the Coulomb’s law fails.
 MERGEFOR

5.2 Electric Field

The space around a charge body where another charge experiences a force of attraction
or repulsion is called the electric field of that charged body.

An electric field is generated by electrically charged particles and time-

varying magnetic fields.

5.2.1 Electric Field Strength or Intensity

The electric field strength or electric field intensity Ē at a point is expressed in

magnitude and direction by the force per unit charge experienced by a small positive
test charge qo placed at that point.
Mathematically, the electric field strength or electric field intensity Eat the point is
defined as

Ē= .

The value of qo should be so small that it should not disturb the electric field. In this
case, the above equation can be written as

E=

5.2.2 Lines of Force

We know, the influence of an electric charge is experienced in the surrounding space of the
charge which is called electric field. If a free positive unit charge is placed in the electric field it
will experience electric force and the charge will move along a particular direction in the electric
field. This path which a free charge follows is called electric line of force.

Lines of force are open lines drawn in the electric field and tangent drawn at any point
on the line gives the direction of the force at that point.
 MERGEFOR

1.

(b)
(a)

(c)

Fig: (a) Field lines around a positive object, (b) Field lines around a negative (c) Two
opposite charge showing their interaction of their field lines .

5.2.3 Characteristics of electric lines of force

Lines of force have the following characteristics:
1) Lines of force are open curved lines.
2) Lines are generated from positive charge and are terminated at the negative
charge.
3) These lines start perpendicularly from the positively charged surface and end
perpendicularly at the negatively charged surface.
4) Two lines of force never intersect.
5) Lines of force apply lateral pressure on each other.
6) They repel each other laterally.
 MERGEFOR

7) No lines of force exist at the interior of the conductor.

8) Tangent drawn at any point of lines of force indicates the direction of the
electric field intensity at that point.

5.2.4 Electric Flux

Electric flux is the rate of flow of the electric field through a given area. Electric flux is
proportional to the number of electric field lines going through a virtual surface. If the
electric field is uniform, the electric flux passing through a surface of vector area S is

Where, Ē is the electric field, E is its magnitude, S is the area of the surface, and θ is the
angle between the electric field lines and the normal (perpendicular) to S.
Think of air blowing in through a window. How much air comes through the window
depends upon the speed of the air, the direction of the air, and the area of the window.
We might call this air that comes through the window the "air flux".

5.3 Gauss's Law

We state Gauss’s law without proof: FIGURE 1.26 Calculation of the
Electric flux through a closed surface S flux of uniform electric field
= q/ε0 (1.31) through the surface of a cylinder.
q = total charge enclosed by S.
The law implies that the total electric flux through a closed surface is
zero if no charge is enclosed by the surface. We can see that explicitly in
the simple situation of Fig. 1.26.
5.3.1 APPLICATIONS OF GAUSS’S LAW

5 .3 .1 .1 Field due to an infinitely

long straight uniformly
charged wire
Consider an infinitely long thin straight wire
with uniform linear charge density λ. The wire
is obviously an axis of symmetry. Suppose we
take the radial vector from O to P and rotate it
around the wire.
Consider a pair of line elements P1 and P2
of the wire, as shown. The electric fields
produced by the two elements of the pair when
summed give a resultant electric field which
is radial (the components normal to the radial
vector cancel). This is true for any such pair
and hence the total field at any point P is
radial. Finally, since the wire is infinite,
electric field does not depend on the position
of P along the length of the wire. In short, the
electric field is everywhere radial in the plane
cutting the wire normally, and its magnitude
depends only on the radial distance r.
To calculate the field, imagine a cylindrical
Gaussian surface, as shown in the Fig. 1.29(b).
Since the field is everywhere radial, flux
through the two ends of the cylindrical
Gaussian surface is zero. At the cylindrical
part of the surface, E is normal to the surface
at every point, and its magnitude is constant,
since it depends only on r. The surface area FIGURE 1.29 (a) Electric field due to an
of the curved part is 2πrl, where l is the length infinitely long thin straight wire is radial,
of the cylinder. (b) The Gaussian surface for a long thin
wire of uniform linear charge density.

Flux through the Gaussian surface

= flux through the curved cylindrical part of the surface
= E × 2πrl
The surface includes charge equal to λ l. Gauss’s law then gives
E × 2πrl = λl/ε0
λ
i.e., E =
2πε 0r

2018-19
 5.3.1.2 Field due to a uniformly charged infinite plane sheet
Let σ be the uniform surface charge density of an infinite plane sheet
(Fig. 1.30). We take the x-axis normal to the given plane. By symmetry,
the electric field will not depend on y and z coordinates and its direction
at every point must be parallel to the x-direction.
We can take the Gaussian surface to be a
rectangular parallelepiped of cross-sectional area
A, as shown. (A cylindrical surface will also do.) As
seen from the figure, only the two faces 1 and 2 will
contribute to the flux; electric field lines are parallel
to the other faces and they, therefore, do not
contribute to the total flux.
The unit vector normal to surface 1 is in –x
direction while the unit vector normal to surface 2
is in the +x direction. Therefore, flux E.∆S through
both the surfaces are equal and add up. Therefore
FIGURE 1.30 Gaussian surface for a the net flux through the Gaussian surface is 2 EA.
uniformly charged infinite plane sheet.
The charge enclosed by the closed surface is σA.
Therefore by Gauss’s law,

2 EA = σA/ε0
or, E = σ/2ε0

2018-19
 5.3.1.3 Field due to a uniformly charged thin spherical shell
Let σ be the uniform surface charge density of a thin spherical shell of
radius R (Fig. 1.31). The situation has obvious spherical symmetry. The
field at any point P, outside or inside, can depend only on r (the radial
distance from the centre of the shell to the point) and must be radial (i.e.,
along the radius vector).
(i) Field outside the shell: Consider a point P outside the
shell with radius vector r. To calculate E at P, we take the
Gaussian surface to be a sphere of radius r and with centre
O, passing through P. All points on this sphere are equivalent
relative to the given charged configuration. (That is what we
mean by spherical symmetry.) The electric field at each point
of the Gaussian surface, therefore, has the same magnitude
E and is along the radius vector at each point. Thus, E and
∆S at every point are parallel and the flux through each
element is E ∆S. Summing over all ∆S, the flux through the
Gaussian surface is E × 4 π r 2. The charge enclosed is
σ × 4 π R 2. By Gauss’s law

σ
E × 4 π r2 = 4 π R2
ε0

σ R2 q
Or, E = =
ε 0 r 2 4 π ε0 r 2
where q = 4 π R2 σ is the total charge on the spherical shell.

(ii) Field inside the shell: In Fig. 1.31(b), the point P is inside the
shell. The Gaussian surface is again a sphere through P centred at O.

The flux through the Gaussian surface, calculated as before, is

E × 4 π r 2. However, in this case, the Gaussian surface encloses no
charge. Gauss’s law then gives FIGURE 1.31 Gaussian
E × 4 π r2 = 0 surfaces for a point with
(a) r > R, (b) r < R.
i.e., E = 0 (r < R ) (1.35)
that is, the field due to a uniformly charged thin shell is zero at all points
inside the shell*. This important result is a direct consequence of Gauss’s
law which follows from Coulomb’s law. The experimental verification of
this result confirms the 1/r2 dependence in Coulomb’s law.

5.4 Electric Potential or Electric Field Potential or Electrostatic

Potential

The electric potential at a point in an electric field is the work required to bring unit
positive electric charge from infinity to the point.
Suppose, we have two points A and B in an electric field. We have a test charge q o from
B to A. If the work done by the agent moving the charge W AB, then

2018-19
 MERGEFOR

Electric potential difference A B

𝑤 VA VB
VA – VB = 𝑞𝐴𝐵 ……………………….(1)
0
Usually, point B is considered to be at infinite distance. In this case V B is assumed to be
zero.
Putting VB= 0 and VA= V, Equation number 1 becomes

V=

This equation gives the general representation of electric potential.

5.4.1 Electric Dipole

If two equal and opposite charges are placed at a

short distance, the formation is called electric
dipole.

5.4.2 Electric Potential Energy

We define the electric potential energy of a system of point charges as the work required
assembling this system of charges by bringing them close together, as in the system from an
infinite distance.

However, we assume that initial kinetic energy of the charges is zero at infinity; they are at rest
at infinity. Thus, an external work done against the forces between the charges and this external
work done is stored in the system as the electrical potential energy of the configuration (or
arrangement) of the charges. As the forces between the charges are of two types, attractive for
opposite charges and repulsive for similar charges. Therefore, the work done will be positive in
the case of like charges and this work done will be negative in the case of unlike (or dissimilar)
charges so that, for similar charges potential energy is positive and for dissimilar it is negative.
 MERGEFOR

5.5 Capacitor

A capacitor is an electric device consisting of two conductors separated by an insulating

or dielectric medium (including air) and carrying equal and opposite charges. The
conductors are called plates and may be of any shape.

+q
+ + ++ + ++ + ++ + ++ + ++ + ++ + ++

Air / Wood

- - - - - - - - - - - - - - - - - - - - - - - -
-q

Figure: A symbolic capacitor

A potential difference will produce between the charge carrying conductors. For a fixed
pair of conductors, the ratio of charges to potential difference will be a constant. This
constant is called capacitance of the capacitor and denoted by C
 MERGEFOR

= Constant = C

Types of capacitor

There are three types of generally used capacitors depending on the size and the
geometrical shapes of the plates

1. A parallel plate capacitor

2. A cylindrical capacitor
3. A spherical capacitor

Dielectric

Substances that can sustain an electric field but acts as an insulator are called dielectric.
If a dielectric placed in an electric field. Induced surfaces charges appear which tend to
weaken the original field within the dielectric.

Capacitance of a parallel plate capacitor

Figure shows a parallel plate capacitor, consists of two parallel conducting plates of
area A separated by a distance d.
ds
+q

+ + ++ + ++ + ++ + ++ + ++ + ++ +

Gaussian Surface

- - - - - - - - - - - - - - - - - - - - - - - -
-q
Fig: A parallel plate capacitor

The electric field strength E between the plates will be uniform, which means that the
lines of force will be parallel and evenly separated. Taking E to be constant throughout
the volume between the plates.
 MERGEFOR

Let us consider, a Gaussian surface enclosed the charge q on the positive plate.
According to Gauss’s law

εo ∫ E . ds = q
εo ∫ E . ds = q (Since, E and ds are parallel)
εo E A = q ………………… (1)

Where, A is the area of the Gaussian surface.

The potential difference between the plates is given by

V = ∫ E . dl

V = E∫ dl (Since, E and dl are parallel)

V=Ed ………………… (2)

Therefore, the capacitance of a parallel plate capacitor is

C=

𝜀
C=

𝜀
C=

This is the required equation for the capacitance of parallel plate type capacitors.

Capacitance of series connected capacitors

Figure shows three capacitors are connected in series, the magnitude of charge q on
each plate must be the same.

We know

C= or v =

Therefore, V1 = , V2 = and V3 =
 MERGEFOR

V = V1 + V2 + V3

= + +

=q( + + )

Capacitance in combination

C= =
( )

= + +

The equivalent series capacitance is always less than the smallest capacitance in the
chain.

Capacitance of parallel connected capacitors

Figure shows three capacitors are connected in parallel. We need to find out the single
capacitance C is equivalent to this combination.

The potential difference across each capacitor in fig. will be the same because all of the
upper plates are connected together with terminal a whereas all of the lower plates with
b.

We know

C=

Q = CV

Therefore

Q1 = C1 V1 , Q2 = C2 V2 and Q3 = C3 V3

Again Fig. Parallel capacitors and their equivalent

Q = Q1 + Q2 + Q3
 MERGEFOR

= (C1 + C2 + C3) V

The equivalent capacitance C is

C= = C1 + C2 + C3

The result can easily be extended to any number of parallel connected capacitor.
 MERGEFOR

5.6 Current

The amount of flow of charge per unit time is known as current. If a net charge q passes
through any cross section of the conductor in time t, the current is given by

I=

The unit of current is Ampere.

1 Ampere =

Therefore,

If 1 coulomb of charge passes through in any cross section of a conductor by 1 sec, the
amount of current is 1 Ampere.

If the electron passes a distance l in time t into a cross sectional area A, then q = nAle,
where, n is the number of electron and e is the charge of electron.

Current Density

The ratio of the current to the cross sectional area of the current – carrying conductor is
known as current density. Current density J can be written as mathematically

J= , where i is the current and A is the cross sectional area. The unit of current density
is Ampere / meter 2

Electrical Resistance or Resistance

The electrical resistance of an electrical conductor is the opposition to the passage of

an electric current through that conductor.

Normally, it is denoted by R. The SI unit of electrical resistance is the ohm (Ω), All
materials show some resistance, except for superconductors, which have a resistance of
zero.

The resistance R of an object is defined as the ratio of voltage across it V

to current through it I. Mathematically,

R=
 MERGEFOR

Resistivity

Electrical resistivity (also known as resistivity, specific electrical resistance, or volume

resistivity) is an intrinsic property that quantifies how strongly a given material
opposes the flow of electric current.

A low resistivity indicates a material that readily allows the movement of electric
charge. Resistivity is commonly represented by theGreek letter ρ. The SI unit of
electrical resistivity is the ohm⋅metre (Ω-m)

Mathematically, electrical resistivity ρ is defined as

Where, R is the resistance, l is the length of the material and A is the cross-sectional
area.

Conductivity

Electrical conductivity or specific conductance is the reciprocal of electrical resistivity,

and measures a material's ability to conduct an electric current.

It is commonly represented by the Greek letter σ, but κ (kappa) (especially in electrical

engineering) or γ (gamma) are also occasionally used. Its SI unit
is Siemens per meter(S/m)

Mathematically, σ can be defined as

Conductivity is the inverse of resistivity.

5.7 Ohm’s Law

Ohm’s law states that the potential difference between the ends of a conductor varies
directly as the current flowing in it, provided the temperature does not change and the
physical state of the conductor remains the same.
 MERGEFOR

If V is the potential difference between two ends of a conductor AB and I is the current
flow in it, then

I∞V

I = GV (where, G is the proportionality constant called conductivity. )

I= V

IR = V

V = IR

Where, R is known as resistance and it is inverse of conductivity. That means if the

resistance of the conductor increases the conductivity decreases. The flow of current
decreases.

Series combination of resistors

Suppose the values of three resistors are respectively R 1, R2 and R3. These are connected
in such a way as that same current flows through each. This combination of resistors is
series combination. The equivalent resistance of the resistors is to be found out.

Let the potential of points A, B, C and D are respectively V A, VB, VC and VD.

Further let V › V.

Let the potential difference between the two ends of resistors are respectively V 1, V2 and
V3. So, from the ohm’s law, we get
 MERGEFOR

VA - VB = V1 , VB - VC = V2, VC - VD = V3

If the potential difference between the two ends of the combination is V, then

V = V1 + V2 + V3 ………… (1)

But if the equivalent resistance of the combination is R s , then from ohm’s law

We get, V = iR from equation number (1) we get

iRs = iR1 + iR2 + iR3

iRs = i (R1 + R2 + R3)

R s = R 1 + R 2 + R3

If there are n number of resistors connected in series

R s = R 1 + R 2 + R3 ……………… + Rn

Parallel combination of resistors

Suppose, the values of three resistors are respectively R 1 ,R2 and R3. One end of each
resistor is connected at point A and the other ends of the resistors are connected at B so
that same potential difference (VA – VB) exists between two ends of each resistor; here
the potential of points A and B are
respectively VA and VB.

Here, current i after reaching at

point A, gets divided into i1, i2 and i3
flowing through respective resistors
R1, R2 and R3 reach at point B and
after combining becomes the main
current i.
 MERGEFOR

i = i1 + i2 + i3 …………………… (1)

From the ohm’s law, we get

i1 = , i2 = and i3 =

If the equivalent resistance of the circuit is R, then from ohm’s law

i=

Now, inserting the values of i1, i2 and i3 in equation (1)

= + +

= + +

If the number of resistors is n

= + + ……….+

Shunt

Shunt is the practical application of parallel combination of resistances. In many

occasions sensitive and sophisticated equipment like galvanometer is used in electric
circuits. A low resistance is used parallel to the equipment in order to protect the
equipment from damage due to the flow of high current through it that produces
excessive heat. So, A low resistance which is used to sensitive and sophisticated
equipment so that high current does not flow through it is called a shunt.

Derive the equation of current flowing through the shunt and the
galvanometer.

Suppose, a resistance S of small value is connected between two ends A and B, parallel
to galvanometer of resistance G. This S is the shunt. Let the principle current in the
circuit be i. While reaching at point A, this current will be divided into two parts.
 MERGEFOR

A small portion of the principle current will flow through galvanometer and large
current will flow through the shunt. As a result, the galvanometer will not be damaged
due to heat produced for large flow of current.

ig
i i

Flow of A B
current G
is
S

Shunt

Two currents will meet at B and will form principle current again. Let this current
through the galvanometer and the shunt be respectively i g and is. Now, if the potential
difference between the points A and B be ( V A – VB) then according to ohm’s law, we get

ig = ………………….. (1)

And

is = …………………..(2)

Dividing equation number 2 by 1

is = i g × ………………….(3)

But, i = i g + is ...……………….(4)

Inserting the value of is in this equation number 4

 MERGEFOR

ig × + ig = i

ig ( + 1) = i

ig =i

Then,

×
ig = = Principle current ×

or

𝑖 = 𝑖𝑔 : Where, is called the power – multiplier of the shunt.

Again, putting the value of ig in equation number 3, we get

×
is = ×
×
is =

And

×
S =

Drift Speed

Drift velocity is the average velocity that a particle, such as an electron, attains due to an
electric field.

Normally, it is denoted by Vd. When an electric field E is established in a conductor, the

charge acquires a drift velocity in the direction of E. The drift velocity V d is related to
the current density (J) by

Vd=

Where, ne is the carrier charge density.

 MERGEFOR

5.8 Magnetic field

The space around a magnet or a current carrying conductor within which it is capable
of attraction or repulsion is known as magnetic field.

Normally, it is denoted by B. the unit of magnetic field is tesla.

1 Tesla = = 104 Gauss

The magnetic field exerts a force on moving charge. Magnetic field is vector quantity.

Magnetic fields are areas where an object exhibits a magnetic influence. The fields affect
neighboring objects along things called magnetic field lines. A magnetic object can
attract or push away another magnetic object. Magnetic poles are the points where the
magnetic field lines begin and end.

Magnetic field of an ideal cylindrical HYPERLINK "http://en.wikipedia.org/wiki/Magnet" \t

"_self" \o "Magnet" magnet. The magnetic field is represented by HYPERLINK
"http://en.wikipedia.org/wiki/Field_line" \t "_self" \o "Field line" magnetic field lines

Magnetic Flux

The strength of magnetic field through an area that is the number of lines of magnetic
force passing through a surface area is called magnetic flux.

It is denoted by φB and mathematically magnetic flux can be defined as

φB = ∫ B . ds

The unit of magnetic flux is weber (wb). Magnetic flux is a scalar quantity.
 MERGEFOR

Magnetic moment

Magnetic moment is defined as the product of the strength of one pole of a magnet to
the magnetic length.

It is denoted by M. It is a vector quantity.

If the strength of one pole of a magnet is m and the magnetic length is 2l, then the
magnetic moment M is given by

M = m. (2l)

Unit of magnetic moment is A-m2

Magnetic Force

If a positive test charge fired with a velocity V through a point P, and if a magnetic
induction B is present at point P, then the magnetic force F can be written as

F = qo ( V × B )

= qoV B Sinθ

Where, θ is the angle between V and B.

Lorentz Force

If a charged particle moves through a region where both an electric and magnetic field
are present, then the resultant force is given by

F = qo E + qo ( V × B )

= qo [ E + ( V × B ) ]

This resultant force is called Lorentz force.

5.9 Hall Effect

The Hall Effect was discovered in 1879 by Edwin Herbert Hall while he was working on
his doctoral degree at Johns Hopkins University in Baltimore, Maryland.

If a magnetic field is applied perpendicularly to the flow of current, then a potential is

created normal to both that current and the magnetic field. This effect is called Hall
Effect and the generated potential is called hall potential.
 MERGEFOR

5.10 Kirchhoff’s Law

Kirchhoff's current law (First Law)

This law is also called Kirchhoff's first law, Kirchhoff's point rule, or Kirchhoff's
junction rule (or nodal rule).
At any node (junction) in an electrical circuit, the sum of currents flowing into that node
is equal to the sum of currents flowing out of that node.
Or equivalently
The algebraic sum of currents in a network of conductors meeting at a point is zero.
 MERGEFOR

According to Kirchhoff’s law

I 1 + I 2 + I3 – I 4 – I 5 = 0

Kirchhoff's voltage law (Second Law)

This law is also called Kirchhoff's second law, Kirchhoff's loop (or mesh) rule,
and Kirchhoff's second rule.
The directed sum of the electrical potential differences (voltage) around any closed
network is zero, or:
More simply, the sum of the emfs in any closed loop is equivalent to the sum of the
potential drops in that loop, or:
The algebraic sum of the products of the resistances of the conductors and the currents
in them in a closed loop is equal to the total emf available in that loop.

According to Kirchhoff’s law

i1R1 + i2R2 – i3R3 = E1 – E2

i1R1 + i2R2 + (– i3R3) = E1 +( – E2)

Symbolically, the above equation can be written as ∑ i R = 0

 MERGEFOR

5.11 Alternating Current

An alternating current is a current that is periodic function of time. In other words, an

alternating current is one which passes through a cycle of regular intervals. In an
alternating current circuit, we are connected with a steady state current and voltage
which are oscillating simultaneously without change in amplitude.

The variation of e.m.f is

ε= ε 0 sin ωt

And, the corresponding current is

I = I0 sin ωt

Where, ε0 and I0 are the peak value of voltage and current respectively at any instant of
time.

There are two methods in general to represent an AC circuit

 MERGEFOR

i) The vector method

ii) The complex number method

The A.C network analysis becomes simple and convenient by the complex number
representation.

A complex number can be written as

Z=x+iy

Where, x is the real part and iy is the imaginary part.

Electromotive force (emf)

Work done to carry a unit positive charge from positive terminal to negative terminal of
a cell is called the electromotive force (emf).

Electromotive force is often denoted by . The unit of the electromotive force of the cell
is volt.

Induced emf

If two coils are near each other, a current in one coil will set up a flux through the
second coil. If this flux is changed by changing the current, an emf will appear in the
second coil according to Faraday’s law. This emf is called induced emf.

Mathematically, it can be written as

ε= ̶

Where, is the rate of change of flux. So, the induced emf is equal to the –ve rate of
change of flux.

5.12 Faraday’s law of induction

Faraday’s law of induction states that, the induced emf ε in a circuit is equal to the
negative rate at which the flux through the circuit is changing.

Mathematically,

ε= ̶
 MERGEFOR

The minus sign is an indication of the direction of the induced emf

For a coil having N turns, the induced emf

( )
ε= ̶ N = ̶

Where, N φB measures the so-called flux linkage in the device.

5.13 Lenz’s Law

An induced electromotive force (emf) always gives rise to a current whose magnetic
field opposes the original change in magnetic flux.
Lenz's law is shown with the negative sign in Faraday's law of induction:

,
This indicates that the induced emf (ℰ) and the change in magnetic flux (∂ΦB) have
opposite signs.

Electromagnetic induction

If an electromotive force is produced in a closed circuit temporarily for a moving

magnet or a current carrying circuit, it is called electromagnetic induction.

5.14 Self Induction

If the current in a coil is changed, then an induced emf appears in that same coil. This
called self induction.

5.15 Mutual Induction

If two coils are near each other, a current in one coil is changed. Then an induced emf
appears in the second coil. This is called mutual induction.
 MERGEFOR

Self Inductance

Let, in a coil for current I, the passing magnetic flux through the coil is (Nφ B), then

N φB ∞ I

N φB = L I

Where, N φB is the number of flux linkage (N being the number of turns)

From, Faraday’s law, the induced emf

( )
ε = ̶
ε = ̶ (LI)
ε =-L

Where, L is a constant called self inductance. That is in a coil, the change in current per
second is unity, then the induced emf appears in that coil is called self-inductance or co-
efficient of self-induction.

Mutual Inductance

Let, for current I1 in primary coil, the passing magnetic flux in the secondary coil will be
N 2 φ2

Then

N 2 φ2 ∞ I 1

N2 φ2 = M I1……………. (1)

Where, N2 φ2 is the number of flux linkage (N being the number of turns in secondary
coil.)

From, Faraday’s law, the induced emf in the secondary coil

ε = ̶ (N2φ2)
 MERGEFOR

ε = ̶ (M I1) using equation number 1.

ε= -M

Where, M is a proportional constant called mutual inductance. That is, in a primary coil,
the change in current per second is unity, then the induce emf in a secondary coil is
called mutual inductance.

Average value ( mean value ) of alternating current over one cycle

The value of current at any time t is given by

I = I0 sin ωt

The average value of a sinusoidal wave over one complete cycle is given by

∫
I =
∫
𝐼0
= ( −𝑐𝑜𝑠 𝜔𝑡 ) ×
𝜔 Where,
𝐼
= - 𝜔0 ( 𝑐𝑜𝑠 𝜔𝑡 ) × ω=

=- ( 𝑐𝑜𝑠 𝜔𝑡 ) ×

𝐼0
=- [cos T – cos 0]

=- [ cos 2𝜋 – cos 0]

= 0
Thus the average value of alternating current over complete cycle is zero.
 MERGEFOR

Average value ( mean value ) of alternating current during half

cycle

The value of current at any time t is given by I = I0 sin ωt. The average value of a
sinusoidal wave over half cycle is given by

∫
I first =
∫

𝐼0 T/2
= 𝜔
( −𝑐𝑜𝑠 𝜔𝑡 ) ×
0 Where,

ω=
𝐼 T/2
= - 𝜔0 ( 𝑐𝑜𝑠 𝜔𝑡 ) ×
0

T/2
=- (𝑐𝑜𝑠 𝜔𝑡 )
0

= - (cos - cos 0)

= - [ cos 𝜋 – cos 0]

=- [ - 1 – 1]

= 0.636 I0

The average value for second half cycle is given by

I second = - 0.636 I0

The average value of alternating current (Voltage) during the 1 st and 2nd half cycles are
equal but opposite in sign. i.e. they are alternatively positive and negative,
 MERGEFOR

Root mean square value of A.C.

The value of current at any time t is given by

I = I0 sin ωt

The average value of I2

2 sin2 A = 1 – cos 2A
2
𝐼𝑜
I2 =

Root mean square value of the

alternating current

= 𝐼 × ×∫ 𝑠𝑖𝑛 𝜔𝑡 dt Ir.m.s =
= × Peak Value
𝜔
= 𝐼 × ×∫ 2 dt
Ir.m.s is also called the virtual value.
= ×
𝜔
×∫ (1 − 𝑐𝑜𝑠 2𝜔𝑡 ) dt It is represented by Iv

𝜔 𝑠𝑖𝑛 T
= × ×[ t - ]
0
𝜔 𝑠𝑖𝑛 .
= × × [T - ]

𝜔 𝑠𝑖𝑛 /
= × ×[ - ]

𝜔
= × ×( - 0)

=
L.C CIRCUIT(NON MECHANICAL OSCILLATION ):-

In this region,it is combination “L” &”C” with the DC source through

the key.If we Press the Key for a while then capacitor get charged &
restores the charge as “+Q” and”-Q” with the potential “v=q/c”
between the plates .When the switch is off the capacitor gets
discharged.
As capacitor gets discharged, q also decreases. So, current at that
situation is given by
I=dq/dt.
As q decreases, electric field energy (Energy stored in electric field )
gradually decreases .This energy is transferred to magnetic field that
appears around the inductor. At a time,all the charge on the capacitor
becomes zero,the energy of capacitor is also Zero. Even though q
equals to zero,the current is zero at this time.
Mathematically, Let the potential difference across the two plates of
capacitor at any instance” V” is given by
V=q/c…………………(1)

In the inductor due to increases in the value of flow of current, the

strength of magnetic field ultimately the magnetic lines of force cut/
link with inductor changes. So a back emfdevelops which is given by

ε =-L …………….(2)

Now applying KVL to this LC circuit,

+v-ε=0

+L =0

+ =0

+ =0………………………..(3).

This represents the general equation of SHM,

Here there is periodic execution of energy between electric field of

capacitor & magnetic field of inductor.

Here this LC oscillation act as an source of electromagnetic wave.

Here, ω 2= ⁄
ω=1/√LC
⇒2π/T=1/√LC
∴T=2π √LC
 MERGEFOR

Mathematical Problems: A
1. Let the total positive and the total negative charges in a copper penny be separated to
a distance such that their force of attraction is 1.0 lb (4.5 Newton). How far apart must
they have?
(Charge of the copper penny is 1.3×10 5 coulomb)

2. At one time the positive charge in the atom was thought to be distributed uniformly
throughout a sphere with a radius of about 1.0×10-10 meter that is throughout the entire
atom. Calculate the electric field strength at the surface of a gold atom (Z = 79) on this
assumption. (Neglect the effect of the electrons.)

3. Calculate the electric field intensity at a point 1m from the charge 100C in air.

4. 20 C charges is given to a sphere of radius of 0.50 m. Find the electric potential at a

distance of 0.50 m and 0.8 m from the centre of the sphere.

5. What must the magnitude of an isolated positive point charge be for the electric
potential at 10 cm from the charge to be +100 volts?

6. What is the electric potential at the surface of a gold nucleus? The radius is 6.6×10 -15
m and the atomic number Z=79.

Q1
7. What is the potential at the center of the square in Fig. (1) Q4
Assume
Q1 = +1.0×10-8 Coulomb
A
 MERGEFOR

Q2 = -2.0×10-8 Coulomb
Q3 = +3.0×10-8 Coulomb
Q4 = +2.0×10-8 Coulomb
A= 1.0 Meter Q2 Q3

8. Two protons in a nucleus of U238 are 6.0×10-15 meter apart. What is their mutual
electric potential energy?

9. Three charges arranged as in Fig. What is their mutual potential energy? Assume that
Q = 1.0×10-7 Coulomb and A = 10 cm.
2Q

3Q
Q

10. What is the magnitude of the electric field strength E such that an electron placed in
the field would experience an electric force equal to its weight?

11. A pith ball of mass 0.002 kg is charged with 10-4 C. What is the magnitude of the
electric field needed to keep the ball at rest in gravitational field?

12. A plastic ball of mass 8.4 × 10-16 kg is kept hanging in an electric field of 2.6 × 10 4
N/C. Calculate the charge in the ball. (g = 10 ms-2)

13. The resistance of a wire of length of 0.48 m and diameter of 0.12 mm is 15 ohm.
Calculate the specific resistance of the material of the wire.

14. If a wire of resistance 6 ohm is elongated three times, its area of cross-section
becomes one third. What will be its final resistance?

15. The resistances of two resistors of the same material are same. If the ratio of the
lengths of the two resistors is 4:9, what is the ratio of their diameter?

16. Three resistors of 5 ohm, 10 ohm and 15 ohm are arranged in series and in parallel.
Determine the equivalent resistance in both the cases.
 MERGEFOR

17. A series combination of two resistors of 2 and 3 ohms is connected across a cell of
electromotive force of 3V. Calculate the potential difference between each resistor.

18. The specific resistance of a wire of diameter of 1 mm is 48×10 -8 ohm. What length of
the wire is needed to make a coil of 100 ohm resistance?

Mathematical Problems: B

1. Three capacitors have capacitances of 3, 2 and 1 μF respectively. Series

combination of second and third capacitors is connected in parallel to the first
capacitor. Calculate the equivalent capacitance of the circuit.

2. The area of each plate of a parallel plate capacitors is 1.5 m 2 and distance
between the plates in air medium is 0.02 m. calculate the capacitance in micro
farad.

3. What is the equivalent capacitance when two capacitors of capacitances 16 𝜇F and

22𝜇F are connected in series?

4. Prove that the equivalent capacitance of 4 capacitors of equal values when

connected in series is times the equivalent capacitance when connected in
parallel.

5. Two parallel plates of capacitors are circular. The radius of each plate is 8×10 -2 m
and the distance between the plates is 2×10-3 m. Determine the amount of charge
deposited on the plates when potential of 100V is applied in the capacitor.
6. Current of 5A is flowing through a conducting wire of radius of 1×10 -3 m.
Calculate the drift velocity of electron if there are 4 ×1028 electrons per meter3 of
the wire. (e = 1.6×10-19 C)
7. A long straight wire is kept fixed in a vertical position and carrier a current in the
vertically upward direction. A magnetic field of intensity 5 ×10 -5 T is available at
a point 0.15 m away from the wire. What is the current in the wire?
 MERGEFOR

8. If an electron is moving with velocity of 105 ms-1 making an angle of 600 with a
uniform magnetic field of 0.50 T, calculate the force acting on it.

9. What shunt resistance is to be added to a galvanometer of resistance of 20 Ω so

that 10 % of total current flows through the galvanometer?

10. A shunt resistance of 20 Ω is connected to a galvanometer of resistance of 100 Ω.

The current in the galvanometer is 0.42 A. What is the current in the circuit?

11. The diameter of a circular coil is 31.4 ×10-2 m and its number of turns is 400. For
what amount of current flow in the coil, the magnetic field at the centre of the
coil will be 4×10-4 Wb-2 .
12. What is the drift velocity for copper wire if the current density is 480 amp/cm 2.

13. Two long straight and parallel wires carry 10 A current in opposite directions.
The wires are apart. Calculate the magnetic induction at the point midway
between the wires. What would be the induction if the currents were in the same
direction?

14. 3 A of current is flowing in a long straight wire. A positive charge, q = 7 𝜇C is

moving parallel to the wire at a distance of 0.05 m with a velocity of 250 ms -1.
Calculate (a) the magnitude of the magnetic field due to the flow of current in the
wire and (b) the force experienced by the charge.

15. Calculate the shunt resistance that is to be added to a galvanometer of resistance

of 99 ohm in order to increase the range of the galvanometer 100 times.

16. The resistance of a galvanometer is 100 ohm. What shunt resistance is to be

added to it so that 99% of the total current flows through the shunt?

17. A galvanometer of resistance o0f 100 ohm can safely pass 1mA current. What
amount of shunt is to be added so that 1A current can be measured?
18. A metallic strip of 0.02 m width is placed perpendicular to the magnetic
induction of 6 Wbm-2. The drift velocity of electron in the strip is 4×10 -3 ms-1.
Determine the generated hall voltage.
6. Modern Physics
6.1 Michelson-Morley Experiment
6.2 Galilean Transformation
6.3
 MERGEFOR

6.4 Bohr Atomic Model

In atomic physics, the Rutherford–Bohr model or Bohr model, introduced by Niels

Bohr in 1913, depicts the atom as a small, positively charged nucleus surrounded
by electrons that travel in circular orbits around the nucleus—similar in structure to
the solar system, but with attraction provided by electrostatic forces rather than gravity.
After the cubic model (1902), the plum-pudding model (1904), the Saturnian
model (1904), and the Rutherford model (1911) came the Rutherford–Bohr model or
just Bohr model for short (1913). The improvement to the Rutherford model is mostly a
quantum physical interpretation of it. The Bohr model has been superseded, but the
quantum theory remains sound.

To overcome this difficulty, Niels Bohr proposed, in 1913, what is now called the Bohr
model of the atom. He suggested that electrons could only have
certain classical motions:

1. Electrons in atoms orbit the nucleus.

2. The electrons can only orbit stably, without radiating, in certain orbits (called by
Bohr the "stationary orbits"[5]) at a certain discrete set of distances from the
nucleus. These orbits are associated with definite energies and are also called
energy shells or energy levels. In these orbits, the electron's acceleration does not
result in radiation and energy loss as required by classical electromagnetics. The
Bohr model of an atom was based upon Planck's quantum theory of radiation.
3. Electrons can only gain and lose energy by jumping from one allowed orbit to
another, absorbing or emitting electromagnetic radiation with a
frequency ν determined by the energy difference of the levels according to
the Planck relation:

Where h is Planck's constant. The frequency of the radiation emitted at an orbit

of period T is as it would be in classical mechanics; it is the reciprocal of the
classical orbit period:
 MERGEFOR

The significance of the Bohr model is that the laws of classical mechanics apply to the
motion of the electron about the nucleus only when restricted by a quantum rule.
Although Rule 3 is not completely well defined for small orbits, because the emission
process involves two orbits with two different periods, Bohr could determine the
energy spacing between levels using Rule 3 and come to an exactly correct quantum
rule: the angular momentum L is restricted to be an integer multiple of a fixed unit:

Where n = 1, 2, 3, ... is called the principal quantum number, and ħ = h/2π. The lowest
value of n is 1; this gives a smallest possible orbital radius of 0.0529 nm known as
the Bohr radius. Once an electron is in this lowest orbit, it can get no closer to the
proton. Starting from the angular momentum quantum rule, Bohr [2] was able to
calculate the energies of the allowed orbits of the hydrogen atom and other hydrogen-
like atoms and ions.

6.5 Photoelectric Effect

When light of appropriate frequency or wavelength is incident on a metal, the electrons

are emitted from that metal. This process of emission of electrons is called photoelectric
emission and the effect is called photoelectric effect.

The electrons emitted due to the influence of light are called photo electrons and current
produced due to the emission is called photoelectric current.
 MERGEFOR

Threshold Frequency

Threshold frequency is defined as the minimum frequency of incident light which can
cause photo electric emission i.e.

This frequency is just able to eject electrons without giving them additional energy.
It is denoted by ⋅o

Work Function

Minimum amount of energy which is necessary to start photo electric emission is called
Work Function. If the amount of energy of incident radiation is less than the work
function of metal, no photo electrons are emitted.

It is denoted by Φ. mathematically, work function of a material is given by, Φ = h⋅ o

It is a property of material. Different materials have different values of work function

Einstein Photoelectric Equation

Suppose, a photon of energy E (E = h ѵ) in incident on an atom of a metallic sheet. There

will be a collision between the photon and electron and this collision will be an elastic
collision. Due to this collision, the electron will absorb whole energy of the photon.
Since, the electron is bound to the nucleus, so some of the portion of the energy will be
used to dissociate the electron from the nucleus; this portion of energy is called work
function (Φ = h ѵo) and the electron will be released with a velocity v along with the rest
of the amount of energy. If the mass of the electron is m then the kinetic energy = mv2
 MERGEFOR

So, from the principle of conservation of energy

E = mv2 + Φ

hѵ= mv2 + Φ

mv2 = hѵ - hѵo

mv2 = h ( ѵ – ѵo)

This is called Einstein’s photoelectric equation.

Photoelectric Cell

The device, working on photoelectric effect, which can transform light energy into
electric energy is called photoelectric cell.

Photoelectric cell of three types

1. Photo-emission cell
2. Photo-voltaic cell
3. Photo-conductive cell
 MERGEFOR

6.6 Radioactivity

Radioactive decay, also known as nuclear decay or radioactivity, is the process by

which a nucleus of an unstable atom loses energy by emitting ionizing radiation. A
material that spontaneously emits this kind of radiation — which includes the emission
of alpha particles, beta particles, gamma rays and conversion electrons — is
considered radioactive.

Radioactivity is of two types

i) Natural Radioactivity
ii) Artificial Radioactivity

There are two units of radioactivity

a. Curie
b. Becquerel

Some heavier elements in the periodic table exhibited radiation as found in nature is
called natural radioactivity.

Applying modern techniques of artificial transmutation of elements have made it

possible to produce radioactivity. Such type of radioactivity is known as artificial or
induced radioactivity.
 MERGEFOR

Alpha particle

An alpha particle consists of two neutrons and two protons ejected from the
nucleus of an atom. The alpha particle is identical to the nucleus of a helium
atom. Examples of alpha emitters are radium, radon, thorium, and uranium.

Because alpha particles are charged and relatively heavy, they interact intensely
with atoms in materials they encounter, giving up their energy over a very short
range. In air, their travel distances are limited to no more than a few centimeters.
As shown in the following illustration, alpha particles are easily shielded against
and can be stopped by a single sheet of paper.

Since alpha particles cannot penetrate the dead layer of the skin, they do not
present a hazard from exposure external to the body.

However, due to the very large number of ionizations they produce in a very
short distance, alpha emitters can present a serious hazard when they are in close
proximity to cells and tissues such as the lung. Special precautions are taken to
ensure that alpha emitters are not inhaled, ingested or injected.

Beta Particle
A beta particle is an electron emitted from the nucleus of a radioactive atom.
Examples of beta emitters commonly used in biological research are: hydrogen-3
(tritium), carbon-14, phosphorus-32, phosphorus-33, and sulfur-35.

Beta particles are much less massive and less charged than alpha particles and
interact less intensely with atoms in the materials they pass through, which give
them a longer range than alpha particles. Some energetic beta particles, such as
those from P-32, will travel up to several meters in air or tens of mm into the
skin, while low energy beta particles, such as those from H-3, are not capable of
penetrating the dead layer of the skin.

Thin layers of metal or plastic stop beta particles.

Gamma Ray
A gamma ray is a packet (or photon) of electromagnetic radiation emitted from
the nucleus during radioactive decay and occasionally accompanying the
emission of an alpha or beta particle. Gamma rays are identical in nature to
other electromagnetic radiations such as light or microwaves but are of much
higher energy.
 MERGEFOR

Examples of gamma emitters are cobalt-60, zinc-65, cesium-137, and radium-226.

Like all forms of electromagnetic radiation, gamma rays have no mass or charge
and interact less intensively with matter than ionizing particles. Because gamma
radiation loses energy slowly, gamma rays are able to travel significant
distances.

Depending upon their initial energy, gamma rays can travel tens or hundreds of
meters in air.

Gamma radiation is typically shielded using very dense materials (the denser
the material, the more chance that a gamma ray will interact with atoms in the
material) such as lead or other dense metals.

Gamma radiation particularly can present a hazard from exposures external to

the body.

Radioactive decay law

In 1902, Rutherfrod and Soddy, after extensive studies formulated a law, known as the
law of radioactive disintegration or decay.

This law states that

“At any moment the number of radioactive atoms that disintegrate in unit time is
directly proportional to the number of unchanged radioactive atoms remaining.”
 MERGEFOR

If the rate of radioactive disintegration of atoms is if N is the number of unchanged

atoms at time t, then

∞-N

=-λN

= - λ dt

Where, λ is the radioactive decay constant.

∫ = - λ dt∫
Log e N = - λ t + C ………………….. (1)

Where, C is the constant of integration.

Suppose, N = N0 at time t = 0

Then

Log e N0 = C

From equation number (1)

Log e N = - λ t + LogeN0

Log e =-λt

= e – λt

N = N0 e – λt

This is the law of radioactive decay or disintegration.

Half Life

The half life of a radioactive element is defined as the time during which the number of
atoms remaining unchanged becomes half of its initial value.
 MERGEFOR

Einstein’s mass-energy equivalent law

In 1905 famous scientist Albert Einstein showed that matter and energy were actually
identical. Matter can be transformed into energy. If a substance of mass m is completely
transformed into energy, the amount of energy obtained is

E = mc2, (here c is the speed of light = 3 × 108 )

This is called the Einstein’s mass-energy equivalent law.

6.7 Nuclear Fission

Nuclear fission is nuclear reaction process in which nucleus, when bombarded with a
neutron, splits into smaller parts, often producing free neutrons, and releasing a very
large amount of energy.
 MERGEFOR

Example: When a uranium nucleus is bombarded by high energy neutrons or protons

or deuterons, then fission takes place. This reaction can be represented as

92235 𝑈 + 01 𝑛 56141 𝐵𝑎 + 3692 𝐾𝑟 + 3 01 𝑛 + energy

6.8 Nuclear Fusion

Nuclear fusion is a nuclear reaction in which two or more atomic nuclei collide at a very
high speed and join to form a new type of atomic nucleus.

During this process, matter is not conserved because some of the matter of the fusing
nuclei is converted to photons (energy).

Example:
 MERGEFOR

6.9 Chain Reaction

Chain reaction is such a process which once started the reaction continues without
requiring further energy and a tremendous amount of energy released because of the
fission of all nuclei.

6.10 Nuclear Reactor

A nuclear reactor is a device to initiate and control a sustained nuclear chain reaction.
Nuclear reactors are used at nuclear power plants for electricity generation and in
propulsion of ships. Heat from nuclear fission is passed to a working fluid (water or
gas), which runs through turbines.
 MERGEFOR

6.11 Mass Defect

The mass of an atom's nucleus is usually less than the sum of the individual masses of
the constituent protons and neutrons when separated. During the splitting of the
nucleus, some of the mass of the nucleus (i.e. some nucleons) gets converted into huge
amounts of energy (according to Einstein's equation E=mc2) and thus this mass is
removed from the total mass of the original particles, and the mass is missing in the
resulting nucleus. This missing mass is known as the mass defect.

Suppose, the actual mass of a nucleus of atomic number A is M, number of protons = Z

and number of neutrons = (A-Z). is the masses of each proton and neutron are
respectively mp and mn

Then the mass defect

ΔM = [Z mp + (A-Z) mn ] – M

Binding Energy

Nuclear binding energy is the energy required to split the nucleus of an atom into its
component parts. The component parts are neutrons and protons, which are collectively
called nucleons. The binding energy of nuclei is usually a positive number, since most
nuclei require net energy to separate them into individual protons and neutrons. If the
mass defect of a nucleus is Δ M, then the binding energy Δ E = M × c 2
 MERGEFOR

6.12 Compton Effect

The Compton Effect (also called Compton scattering) is the result of a high-energy
photon colliding with a target, which releases loosely bound electrons from the outer
shell of the atom or molecule. The scattered radiation experiences a wavelength shift
that cannot be explained in terms of classical wave theory, thus lending support to
Einstein's photon theory.

The effect was first demonstrated in 1923 by Arthur Holly Compton (for which he
received a 1927 Nobel Prize)

6.13 Pair production

Pair production is a phenomenon of nature where energy is converted to mass. In this

phenomenon a wave of energy or a photon (a packet of energy) interacts with a heavy
nucleus to form an electron - positron pair.

Pair production is the creation of an elementary particle and its antiparticle.

 MERGEFOR

✔ Calculate the energy of one atomic mass unit in MeV

By using Einstein’s mass-energy equation, the energy equivalence of 1 a.m.u can be

found easily

1 amu = 1.66 × 10-27 Kg

And C = 3 × 108 ms-1

E = mc2 = 1.66 × 10-27 × (3 × 108)2

= 14.9 × 10-11 Joules

Again

1.6 × 10-19 Joules = 1 eV

−11
14.9 ×10
14.9 × 10-11 Joules = −19 = 931.25 × 106 eV
1.6 ×10

= 931 MeV
 MERGEFOR

Derivation of Einstein’s mass-energy relation

We know from the second law of motion that rate of change of momentum is called
force. So

F= (mv)

We know from the theory of special relativity that both mass and velocity vary.

F= (mv)

=m v+v m …………….. (1)

Suppose, force F creates displacement of dx of a body. So, work done = F. dx. Then the
increase in kinetic energy (dEk) of the body is equal to the work done (F. dx)

dEk = F. dx

= (m v+v m ) . dx

=m dv + v dm

= mv dv + v2 dm ………….. (2)

From the relation of mass and velocity

𝑚0
m=
2
1− 𝑣2
𝑐

Squaring both sides, we get

m2 =

m2c2 – m2v2 = 𝑚 c2

or, m2c2 = m2v2 + 𝑚 c2

Differentiating both sides

2m. dm c2 = 2m dm v2 + 2v dv m2
 MERGEFOR

dm c2 = (mv dv + v2 dm) …………. (3)

From (2) and (3)

dm c2 = dEK …………. (3)

It can be written as

dEK ∝ dm

If the object is stationary, then v = 0 and K.E = 0. In this condition m = m o , but when the
velocity of the body is v, then the mass is m.

∫ 𝑑𝐸 = ∫ 𝑑𝑚 𝑐

Ek = c 2 ∫ 𝑑𝑚
m
Ek = c2 ⌊ 𝑚⌋
m0

Ek = c2 (m – mo)

Ek = m c2 – mo c2

This is the relativistic formula for kinetic energy.

When the body is at rest, the internal energy stored in the body is m o c2. This energy is
called rest mass energy

So, the total energy of the body

E = kinetic energy + rest mass energy

E = Ek + mo c2

E = m c2 – mo c2 + mo c2

E = mc2

This is Einstein’s mass – energy relation.

MATH
 MERGEFOR

Mathematical Problems
1. Express the energy of a quantum of light of wavelength 4 × 10 -7 m in electron
volt. ( h = 6.63 × 10-34 Js )
2. Calculate the frequency and wavelength of a photon of energy of 100 MeV.
3. Calculate the velocity achieved by an electron at rest when it is passed through a
potential difference of 10 kilo volt.
4. An ultraviolet ray of wavelength of 2500 A 0 is incident on a metal surface. If the
work function of the metal is 2.3 eV. What is the maximum velocity of the
emitted photoelectron?
5. The threshold wavelength of sodium is 6800 A 0 . Calculate its work function.
6. The work function of platinum is 6.31 eV. What is its threshold frequency? ( h =
6.63 × 10-34 Js )
7. When radiation of frequency of 4 × 1015 Hz is incident on a metal surface,
electron of maximum energy of 3.6 × 10-19 J is emitted. What is the threshold
frequency of that metal?
8. The work function of a metal is 1.85 eV. What is its threshold frequency?
9. A metal surface is exposed to light of wavelength of 6000 A0 . 1.77 eV is required
to remove an electron. What is the kinetic energy of the fastest electron? What is
the threshold frequency? ( h = 6.63 × 10 -34 Js and 1eV = 1.6 × 10-19 J)
10. What is the energy of an X-ray photon of wavelength of 2× 10 -10 m?
11. The half life of a radioactive element is 4d. Determine the decay constant of the
element.
12. What time will it take to decay 60% of a piece of radon? Half life of radon is 3.82
days.
13. If 108 numbers of atoms of radon initially remains in a piece of a substance, then
how many atoms will disintegrate in one day? Half life of radon is 4 days.
14. The half life of a radioactive substance is 10 days. After how many days 75% of
that substance will be disintegrated?
15. The decay constant of a radioactive substance is 3.75 × 10 -3 sec-1 . Calculate its half
life.
16. A piece of radium is transformed by radioactive emission to th of its initial
mass in 4000 years. Calculate the decay constant of radium.

17. If an electron moves with a velocity of 0.99c, what is its mass?

 MERGEFOR

18. A particle is moving with velocity of 0.5c. Determine the ratio of the mass at rest
to the moving mass of the particle.

19. The rest mass of an electron is 9.028× 10-31 Kg. Find its equivalent energy.What
will be the value in eV ?

20. The total energy of a moving particle is 2.5 times the stationary energy, what is
the speed of the particle?

21. What is the mass of an electron having kinetic energy of 1.6× 10 6 eV ?

22. The mass of a particle is 9.1× 10-28 Kg. If it is totally converted into energy, how
much energy will be obtained? (c = 3 × 10 8 ms-1)

23. Calculate the mass and speed of an electron having kinetic energy of 1.5 × 10 6 eV
according to the theory of relativity.

24. Determine the equivalent energy of 1g mass in (i) Joule (ii) MeV.

25. The mass of an object is 8.30 × 10-3 Kg. It is converted totally into energy. How
much energy will be generated?

26. Express the equivalent energy of 10 amu mass.

27. Express the equivalent energy of 12 amu mass in (i) eV, (ii) MeV.

28. Determine the momentum, kinetic energy and total energy of a particle moving
with velocity .
√
29. Total energy of a particle is twice its stationary energy. What is the speed of the
particle?

30. The mass of a star is 4M0. If the star is transformed into a black hole, then what
will its Schwarzchild or critical radius? (Mass of the sun, M 0 = 1.99× 1030 Kg)

31. Calculate the binding energy when

(i) One neutron and one proton combine to form a deuteron.

 MERGEFOR

(ii) Two neutrons and two protons combine to form an Alpha particle.

32. The mass of 17𝑐𝑙 is 34.9800 amu. Calculate its binding energy. What is the
binding energy per nucleon?
(Mass of 0𝑛 = 1.008665 amu and 1𝐻 = 1.007825 amu)