DYNAMIXEL PLATFORM STEAM SOFTWARE PARTS FAQ ROBOTIS Robot Source GitHub

Enter Search Terms

Edit on GitHub
XM430-W350

1. Specifications ▲
TOP
1. 1. Performance Graph

2. Control Table

2. 1. Control Table, Data, Address

- Area(EEPROM, RAM)
XM430-W350
- Size
- Access
- Initial Value 1. Specifications
2. 2. EEPROM Area Item Specifications

2. 3. RAM Area MCU ARM CORTEX-M3 (72 [MHz], 32Bit)

2. 4. Control Table Description
Contactless absolute encoder (12Bit, 360 [°])
Position Sensor
- Model Number(0) Maker : ams(www.ams.com), Part No : AS5045
- Firmware Version(6)
Motor Coreless
- ID(7)
- Baud Rate(8) Baud Rate 9,600 [bps] ~ 4.5 [Mbps]
- Return Delay Time(9)
Control Algorithm PID control
- Drive Mode(10)
- Operating Mode(11) Resolution 4096 [pulse/rev]

- Secondary(Shadow) ID(12) Backlash 15 [arcmin] (0.25 [°])

- Protocol Version(13)
- Homing Offset(20) Current Control Mode
Velcoity Control Mode
- Moving Threshold(24)
Position Control Mode (0 ~ 360 [°])
- Temperature Limit(31) Operating Modes
Extended Position Control Mode (Multi-turn)
- Min/Max Voltage Limit(32,34) Current-based Position Control Mode
- PWM Lmit(36) PWM Control Mode (Voltage Control Mode)
- Current Limit(38)
Weight 82 [g]
- Velocity Limit(44)
- Min/Max Position Limit(48, 52) Dimensions (W x H x D) 28.5 x 46.5 x 34 [mm]

- Shutdown(63) Gear Ratio 353.5 : 1

- Torque Enable(64)
3.8 [N.m] (at 11.1 [V], 2.1 [A])
LED(65)
Stall Torque 4.1 [Nm] (at 12.0 [V], 2.3 [A])
4.8 [Nm] (at 14.8 [V], 2.7 [A])

43 [rev/min] (at 11.1 [V])

No Load Speed 46 [rev/min] (at 12.0 [V])
57 [rev/min] (at 14.8 [V])

Radial Load 40 [N] (10 [mm] away from the horn)

Axial Load 20 [N]

Operating Temperature -5 ~ +80 [°C]

Input Voltage 10.0 ~ 14.8 [V] (Recommended : 12.0 [V])

Command Signal Digital Packet

TTL Half Duplex Asynchronous Serial Communication with 8bit, 1stop, No Parity
Protocol Type
RS485 Asynchronous Serial Communication with 8bit, 1stop, No Parity

Physical Connection RS485 / TTL Multidrop Bus

ID 253 ID (0 ~ 252)

Feedback Position, Velocity, Current, Realtime tick, Trajectory, Temperature, Input Voltage, etc

Full Metal Gear

Part Material
Metal (Front, Middle), Engineering Plastic (Back)

Standby Current 40 [mA]

DANGER
(May cause serious injury or death)
Never place items containing water, flammables, and solvents near product.
Never place fingers, arms, toes, and other body parts near product during operation.
Cut power off if product emits strange odors or smoke.
Keep product out of reach of children.
Check the power polarity before wiring.

CAUTION
(May cause injury or damage to product)
Do not operate the product at a temperature exceeding -5 ~ +80 [°C] range.
Do not insert sharp blades nor pins during product operation.

ATTENTION
(May cause injury or damage to product)
Do not disassemble or modify product.
Do not drop or apply strong shock to product.

1. 1. Performance Graph

NOTE : The Max Torque and the Stall Torque of Performance Graph are different in measurement methods. Stall torque is a measured value of the momentary torque that it can reach. This is generally how RC
servos are measured. The Performance graph is also called as N-T curves, which is measured with the gradually increasing load. The actual motor operation environment is closer to the performance graph, not
stall torque method. For this reason, the performance graph is broadly used in the industrial field. Generally, Max Torque of the Performance Graph is less than the Stall Torque.

CAUTION : When supplying power

It is recommended using ROBOTIS controller or SMPS2DYNAMIXEL.
Do not connect or disconnect DYNAMIXEL when power is being supplied.

2. Control Table
The Control Table is a structure of data implemented in the device. Users can read a specific Data to get status of the device with Read Instruction Packets, and modify Data as well to control the
device with WRITE Instruction Packets.

2. 1. Control Table, Data, Address

The Control Table is a structure that consists of multiple Data fields to store status or to control the device. Users can check current status of the device by reading a specific Data from the
Control Table with Read Instruction Packets. WRITE Instruction Packets enable users to control the device by changing specific Data in the Control Table. The Address is a unique value when
accessing a specific Data in the Control Table with Instruction Packets. In order to read or write data, users must designate a specific Address in the Instruction Packet. Please refer to Protocol
2.0 for more details about Instruction Packets.

NOTE : Two’s complement is applied for the negative value. For more information, please refer to Two’s complement from Wikipedia.

2. 1. 1. Area (EEPROM, RAM)

The Control Table is divided into 2 Areas. Data in the RAM Area is reset to initial values when the power is reset(Volatile). On the other hand, data in the EEPROM Area is maintained even
when the device is powered off(Non-Volatile).

Data in the EEPROM Area can only be written to if Torque Enable(64) is cleared to ‘0’(Off).

2. 1. 2. Size
The Size of data varies from 1 ~ 4 bytes depend on their usage. Please check the size of data when updating the data with an Instruction Packet. For data larger than 2 bytes will be saved
according to Little Endian.

2. 1. 3. Access
The Control Table has two different access properties. ‘RW’ property stands for read and write access permission while ‘R’ stands for read only access permission. Data with the read only
property cannot be changed by the WRITE Instruction. Read only property(‘R’) is generally used for measuring and monitoring purpose, and read write property(‘RW’) is used for controlling
device.

2. 1. 4. Initial Value
Each data in the Control Table is restored to initial values when the device is turned on. Default values in the EEPROM area are initial values of the device (factory default settings). If any
values in the EEPROM area are modified by a user, modified values will be restored as initial values when the device is turned on. Initial Values in the RAM area are restored when the
device is turned on.

2. 2. Control Table of EEPROM Area

Size Default
Address Data Name Access Range Unit
(Byte) Value

0 2 Model Number R 1,020 - -

2 4 Model Information R - - -

6 1 Firmware Version R - - -

7 1 ID RW 1 0 ~ 253 -

8 1 Baud Rate RW 1 0~7 -

9 1 Return Delay Time RW 250 0 ~ 254 2 [μsec]

10 1 Drive Mode RW 0 0~1 -

11 1 Operating Mode RW 3 0 ~ 16 -

12 1 Secondary(Shadow) ID RW 255 0 ~ 252 -

13 1 Protocol Type RW 2 1~2 -

-1,044,479 ~
20 4 Homing Offset RW 0 1 [pulse]
1,044,479

24 4 Moving Threshold RW 10 0 ~ 1,023 0.229 [rev/min]

31 1 Temperature Limit RW 80 0 ~ 100 1 [°C]

32 2 Max Voltage Limit RW 160 95 ~ 160 0.1 [V]

34 2 Min Voltage Limit RW 95 95 ~ 160 0.1 [V]

36 2 PWM Limit RW 885 0 ~ 885 0.113 [%]

38 2 Current Limit RW 1,193 0 ~ 1,193 2.69 [mA]

44 4 Velocity Limit RW 200 0 ~ 1,023 0.229 [rev/min]

48 4 Max Position Limit RW 4,095 0 ~ 4,095 1 [pulse]

52 4 Min Position Limit RW 0 0 ~ 4,095 1 [pulse]

63 1 Shutdown RW 52 - -

2. 3. Control Table of RAM Area

Size Default
Address Data Name Access Range Unit
(Byte) Value

64 1 Torque Enable RW 0 0~1 -

65 1 LED RW 0 0~1 -

68 1 Status Return Level RW 2 0~2 -

69 1 Registered Instruction R 0 0~1 -

70 1 Hardware Error Status R 0 - -

76 2 Velocity I Gain RW 1,920 0 ~ 16,383 -

78 2 Velocity P Gain RW 100 0 ~ 16,383 -

80 2 Position D Gain RW 0 0 ~ 16,383 -

82 2 Position I Gain RW 0 0 ~ 16,383 -

84 2 Position P Gain RW 800 0 ~ 16,383 -

88 2 Feedforward 2nd Gain RW 0 0 ~ 16,383 -

90 2 Feedforward 1st Gain RW 0 0 ~ 16,383 -

98 1 Bus Watchdog RW 0 1 ~ 127 20 [msec]

-PWM Limit(36) ~
100 2 Goal PWM RW - -
PWM Limit(36)

-Current Limit(38) ~
102 2 Goal Current RW - 2.69 [mA]
Current Limit(38)

-Velocity Limit(44) ~
104 4 Goal Velocity RW - 0.229 [rev/min]
Velocity Limit(44)

0 ~ 32,767 214.577 [rev/min2]

108 4 Profile Acceleration RW 0
0 ~ 32,737 1 [ms]

112 4 Profile Velocity RW 0 0 ~ 32,767 0.229 [rev/min]

Min Position Limit(52) ~

116 4 Goal Position RW - 1 [pulse]
Max Position Limit(48)

120 2 Realtime Tick R - 0 ~ 32,767 1 [msec]

122 1 Moving R 0 0~1 -

123 1 Moving Status R 0 - -

124 2 Present PWM R - - -

126 2 Present Current R - - 2.69 [mA]

128 4 Present Velocity R - - 0.229 [rev/min]

132 4 Present Position R - - 1 [pulse]

136 4 Velocity Trajectory R - - 0.229 [rev/min]

140 4 Position Trajectory R - - 1 [pulse]

144 2 Present Input Voltage R - - 0.1 [V]

146 1 Present Temperature R - - 1 [°C]

168 2 Indirect Address 1 RW 224 64 ~ 661 -

170 2 Indirect Address 2 RW 225 64 ~ 661 -

172 2 Indirect Address 3 RW 226 64 ~ 661 -

… … … … … - -

218 2 Indirect Address 26 RW 249 64 ~ 661 -

220 2 Indirect Address 27 RW 250 64 ~ 661 -

222 2 Indirect Address 28 RW 251 64 ~ 661 -

224 1 Indirect Data 1 RW 0 0 ~ 255 -

225 1 Indirect Data 2 RW 0 0 ~ 255 -

226 1 Indirect Data 3 RW 0 0 ~ 255 -

… … … … … - -

249 1 Indirect Data 26 RW 0 0 ~ 255 -

250 1 Indirect Data 27 RW 0 0 ~ 255 -

251 1 Indirect Data 28 RW 0 0 ~ 255 -

578 2 Indirect Address 29 RW 634 64 ~ 661 -

580 2 Indirect Address 30 RW 635 64 ~ 661 -

582 2 Indirect Address 31 RW 636 64 ~ 661 -

… … … … … - -

628 2 Indirect Address 54 RW 659 64 ~ 661 -

630 2 Indirect Address 55 RW 660 64 ~ 661 -

632 2 Indirect Address 56 RW 661 64 ~ 661 -

634 1 Indirect Data 29 RW 0 0 ~ 255 -

635 1 Indirect Data 30 RW 0 0 ~ 255 -

636 1 Indirect Data 31 RW 0 0 ~ 255 -

… … … … … - -

659 1 Indirect Data 54 RW 0 0 ~ 255 -

660 1 Indirect Data 55 RW 0 0 ~ 255 -

661 1 Indirect Data 56 RW 0 0 ~ 255 -

CAUTION : Protocol 1.0 does not support addresses greater than 256. Therefore, Indirect Address 29 ~ 56 and Indirect Data 29 ~ 56 can only be accessed with Protocol 2.0.

2. 4. Control Table Description

CAUTION : Data in the EEPROM Area can only be written when the value of Torque Enable(64) is cleared to ‘0’.

2. 4. 1. Model Number(0)
This address stores model number of the DYNAMIXEL.

2. 4. 2. Firmware Version(6)
This address stores firmware version of the DYNAMIXEL.

2. 4. 3. ID(7)
The ID is a unique value in the network to identify each DYNAMIXEL with an Instruction Packet. 0~252 (0xFC) values can be used as an ID, and 254(0xFE) is occupied as a broadcast ID.
The Broadcast ID(254, 0xFE) can send an Instruction Packet to all connected DYNAMIXELs simultaneously.

NOTE : Please avoid using an identical ID for multiple DYNAMIXELs. You may face communication failure or may not be able to detect Dynamixels with an identical ID.

2. 4. 4. Baud Rate(8)
Baud Rate determines serial communication speed between a controller and DYNAMIXELs.

Value Baud Rate Margin of Error

7 4.5M 0.000%

6 4M 0.000%

5 3M 0.000%

4 2M 0.000%

3 1M 0.000%

2 115,200 0.000%

1(Default) 57,600 0.000%

0 9,600 0.000%

NOTE : Less than 3% of the baud rate error margin will not affect to UART communication.

NOTE : For the stable communication with higher Baudrate, configure USB Latency value to the lower.
USB Latency Setting

2. 4. 5. Return Delay Time(9)

After the DYNAMIXEL receives an Instruction Packet, it delays transmitting the Status Packet for Return Delay Time(9). For instance, if the Return Delay Time(9) is set to ‘10’, the Status
Packet will be returned after 20[μsec] when the Instruction Packet is received.

Unit Value Range Description

2[μsec] 0 ~ 254 Default value ‘250’(500[μsec]), Maximum 508[μsec]

2. 4. 6. Drive Mode(10)
This address configures Drive Mode of DYNAMIXEL. Drive Mode is available from the firmware V38.

Bit Item Description

Bit 7(0x80) - Unused, always ‘0’

Bit 6(0x40) - Unused, always ‘0’

Bit 5(0x20) - Unused, always ‘0’

Bit 4(0x10) - Unused, always ‘0’

Bit 3(0x08) - Unused, always ‘0’

[0] Velocity-based Profile: Create a Profile based on Velocity

Bit 2(0x04) Profile Configuration [1] Time-based Profile: Create Profile based on time
※ Please refer to Profile Velocity(112)

Bit 1(0x02) - Unused, always ‘0’

[0] Normal Mode: CCW(Positive), CW(Negative)

Bit 0(0x01) Normal/Reverse Mode
[1] Reverse Mode: CCW(Negative), CW(Positive)

NOTE : Time-based Profile is available from firmware V42.

NOTE : If the value of Bit 0(Normal/Reverse Mode) of the Drive Mode(10) is set to 1 , rotational direction is inverted.
Thus, Goal Position, Present Position will have a inverted direction.
This feature can be very useful when configuring symmetrical joint or wheel system.

2. 4. 7. Operating Mode(11)

Value Operating Mode Description

DYNAMIXEL only controls current(torque) regardless of speed and position. This mode is ideal for a gripper or a system that only uses current(torque) control or a system that has
0 Current Control Mode
additional velocity/position controllers.

1 Velocity Control Mode This mode controls velocity. This mode is identical to the Wheel Mode(endless) from existing DYNAMIXELs. This mode is ideal for wheel-type robots.

This mode controls position. This mode is identical to the Joint Mode from existing DYNAMIXELs. Operating position range is limited by Max Position Limit(48) and Min Position Limit(52).
3(Default) Position Control Mode
This mode is ideal for articulated robots that each joint rotates less than 360 degrees.

Extended Position Control This mode controls position. This mode is identical to the Multi-Turn Mode from existing DYNAMIXELs. 512 turns are supported(-256[rev] ~ 256[rev]). This mode is ideal for multi-turn
4
Mode(Multi-turn) wrists or conveyer systems or a system that requires an additional reduction gear.

Current-based Position This mode controls both position and current(torque). Up to 512 turns are supported(-256[rev] ~ 256[rev]). This mode is ideal for a system that requires both position and current control
5
Control Mode such as articulated robots or grippers.

PWM Control Mode (Voltage

16 This mode directly controls PWM output. (Voltage Control Mode)
Control Mode)

NOTE : Switching Operating Mode will reset gains(PID, Feedfoward) properly to the selected Operating Mode. The profile generator and limits will also be reset.
1. Profile Velocity(112), Profile Acceleration(108) : Reset to ‘0’
2. Goal PWM(100), Goal Current(102) : Reset to PWM Limit(36), Current Limit(38) respectively
3. Current-based Position Control Mode : Reset to Position Gain(PID) and PWM Limit(36) values.
Changed Position Gain(PID) and PWM Limit(36) values can be read from the Control Table.

NOTE : PWM is the abbreviation for Pulse Width Modulation that modulates PWM Duty to control motors.
The PWM Control Mode changes pulse width to control average supply voltage to the motor and this technique is widely used in the motor control field.
Therefore, PWM Control Mode uses Goal PWM(100) value to control supply voltage for DYNAMIXEL.
PWM Control Mode is similar to the Wheel Mode of DYNAMIXEL AX and RX series.

2. 4. 8. Secondary(Shadow) ID(12)
Set the Dynamixel’s Secondary ID. Secondary ID(12) is a value to identify each Dynamixel, just like the ID(7). However, unlike ID(7), Secondary ID(12) is not a unique value. Therefore,
Dynamixels with the same Secondary ID value form a group. The differences between Secondary ID(12) and ID(7) are as follows :
1. Secondary ID(12) is not a unique value. i.e., a lot of Dynamixels may have the same Secondary ID value.
2. ID(7) has a higher priority than Secondary ID(12). i.e., if Secondary ID(12) and ID(7) are the same, ID(7) will be applied first.
3. The EEPROM area of the Control Table cannot be modified with Secondary ID(12). Only the RAM area can be modified.
4. If Instruction Packet ID is the same as Secondary ID(12), the Status Packet will not be returned.
5. If the value of Secondary ID(12) is 253 or higher, the Secondary ID function is deactivated.

Values Description

0 ~ 252 Activate Secondary ID function

253 ~ 255 Deactivate Secondary ID function, Default value ‘255’

The following are examples of operation when there are five Dynamixels with ID (7) set from 1 to 5.
1. Set all five Dynamixels’ Secondary ID(12) to ‘5’.
2. Send Write Instruction Packet(ID = 1, LED(65) = 1).
3. Turn on LED of Dynamixel with ID ‘1’ and return the Status Packet.
4. Send Write Instruction Packet(ID = 5, LED(65) = 1).
5. Turn on LED on five Dynamixels. However, Status Packet of Dynamixel with ID ‘5’ will be returned.
6. Set the Secondary ID(12) of all five Dynamixels to ‘100’.
7. Send Write Instruction Packet(ID = 100, LED(65) = 0).
8. Turn off LED on five Dynamixels. However, as there is no Dynamixel with ID ‘100’, Status Packet is not returned.

2. 4. 9. Protocol Type(13)
Users can select Dynamixel protocol version (1.0 and 2.0).
Even if Protocol 1.0 is selected, Protocol 2.0 Control Table will be used.
It is recommended to use an identical protocol version for multiple Dynamixels.

Value Protocol Version Compatible Dynamixels

1 1.0 AX Series, DX Series, RX Series, EX Series, MX Series with Firmware below v39

2(default) 2.0 MX-28/64/106 with Firmware v39 or above, X Series, PRO Series

WARNING : In order to change the Protocol Type to Protocol 1.0, please use DYNAMIXEL Wizard 2.0 as R+ Manager 2.0 does not support Protocol 1.0.

NOTE : The protocol 2.0 is greatly enhanced from the protocol 1.0. Accessing some of the Control Table area might be denied if protocol 1.0 is selected. This manual complies with protocol 2.0. Please refer
to the Protocol 1.0 and Protocol 2.0 of e-Manual for more details about the protocol.

NOTE : Please refer to the Protocol Compatibility table for product.

2. 4. 10. Homing Offset(20)

Users can adjust the Home position by setting Home Offset(20). The Homing Offset value is added to the Present Position(132).
Present Position(132) = Actual Position + Homing Offset(20)

Unit Value Range Description

-1,044,479 ~ 1,044,479
about 0.088 [°] 4,096 resolution
(-255 ~ 255[rev])

NOTE : In case of the Position Control Mode(Joint Mode) that rotates less than 360 degrees, any invalid Homing Offset(20) values will be ignored(valid range : -1,024 ~ 1,024).

NOTE : In the case of Reverse Mode bit is set in Drive Mode(10), the sign of Homing Offset value will not be reversed.

2. 4. 11. Moving Threshold(24)

This value helps to determine whether the Dynamixel is in motion or not.
When the absolute value of Present Velocity(128) is greater than the Moving Threshold(24), Moving(122) is set to ‘1’, otherwise it is cleared to ‘0’.

Values Description

Unit about 0.229 rpm All velocity related Data uses the same unit

Range 0 ~ 1,023 -

2. 4. 12. Temperature Limit(31)

This value limits operating temperature.
When the Present Temperature(146) that indicates internal temperature of Dynamixel is greater than the Temperature Limit(31), the Over Heating Error Bit(0x04) and Hardware Error
Bit(0x80) in the Hardware Error Status(70) will be set.
If Overheating Error Bit(0x04) is configured in the Shutdown(63), Torque Enable(64) is cleared to ‘0’ and Torque will be disabled.
For more details, please refer to the Shutdown(63) section.

Unit Value Range Description

About 1° 0 ~ 100 0 ~ 100°

CAUTION : Do not set the temperature higher than the default value. When the temperature alarm shutdown occurs, wait 20 minutes to cool the temperature before re-use. Keep using the product when the
temperature is high can cause severe damage.

2. 4. 13. Min/Max Voltage Limit(32, 34)

These values are maximum and minimum operating voltages. When present input voltage acquired from Present Input Voltage(144) exceeds the range of Max Voltage Limit(32) and Min
Voltage Limit(34), Input Voltage Error Bit(0x01) in the Hardware Error Status(70) are set.
If Input Voltage Error Bit(0x10) is configured in the Shutdown(63), Torque Enable(64) is cleared to ‘0’ and Torque is disabled.
For more details, please refer to the Shutdown(63) section.

Unit Value Range Description

About 0.1 [V] 95 ~ 160 9.5 ~ 16.0 [V]

2. 4. 14. PWM Limit(36)

This value indicates maximum PWM output. Goal PWM(100) can’t be configured with any values exceeding PWM Limit(36). PWM Limit(36) is commonly used in all operating mode as an
output limit, therefore decreasing PWM output will result in decreasing torque and velocity. For more details, please refer to the Gain section of each operating modes.

Values Description

0(0 [%]) ~ 885(100 [%]) 885 = 100 [%] output

2. 4. 15. Current Limit(38)

This value indicates maximum current(torque) output limit. Goal Current(102) can’t be configured with any values exceeding Current Limit(38). The Current Limit(38) is used in Torque
Control Mode and Current-based Position Control Mode, therefore decreasing Current Limit(38) will result in decreasing torque of DYNAMIXEL. For more details, please refer to the Position
PID Gain(80 ~ 84).

Unit Value Range

about 2.69[mA] 0 ~ 1,193

NOTE : Current Limit(38) could be differ by each DYNAMIXEL so please check the Control Table.

2. 4. 16. Velocity Limit(44)

This indicates the maximum value of Goal Velocity(104). For more details, please refer to Goal Velocity(104).

Unit Value Range

0.229rpm 0 ~ 1,023

NOTE: The default value of Velocity Limit(44) has been decreased since Firmware V42.

2. 4. 17. Min/Max Position Limit(48, 52)

These values limit maximum and minimum desired positions for Position Control Mode(Joint Mode) within the range of 1 rotation(0 ~ 4,095).
Therefore, Goal Position(116) should be configured within the position limit range.
These values are not used in Extended Position Control Mode and Current-based Position Control Mode.

Unit Value Range

0.088 [°] 0 ~ 4,095(1 rotation)

NOTE : Max Position Limit(48) and Min Position Limit(52) are only used in Position Control Mode with a single turn.

2. 4. 18. Shutdown(63)
The Dynamixel can protect itself by detecting dangerous situations that could occur during the operation.
Each Bit is inclusively processed with the ‘OR’ logic, therefore, multiple options can be generated.
For instance, when ‘0x05’ (binary : 00000101) is defined in Shutdown(63), Dynamixel can detect both Input Voltage Error(binary : 00000001) and Overheating Error(binary : 00000100).
If those errors are detected, Torque Enable(64) is cleared to ‘0’ and the motor output becomes 0[%].
REBOOT is the only method to reset Torque Enable(64) to ‘1’(Torque ON) after the shutdown.
The followings are detectable situations.

Bit Item Description

Bit 7 - Unused, Always ‘0’

Bit 6 - Unused, Always ‘0’

Bit 5 Overload Error(default) Detect persistent load that exceeds maximum output

Bit 4 Electrical Shock Error(default) Detect electric shock on the circuit or insufficient power to operate the motor

Bit 3 Motor Encoder Error Detect malfunction of the motor encoder

Bit 2 OverHeating Error(default) Detect internal temperature exceeds the configured operating temperature

Bit 1 - Unused, Always ‘0’

Bit 0 Input Voltage Error Detect input voltage exceeds the configured operating voltage

NOTE : If Shutdown occurs, use below method to reboot Dynamixels.

1. H/W REBOOT : Turn off the power and turn on again
2. S/W REBOOT : Transmit REBOOT Instruction (For more details, please refer to the Reboot section of Protocol e-Manual.)

NOTE : If Shutdown occurs, LED will flicker every second.(Firmware v41 or above)

2. 4. 19. Torque Enable(64)

Controls Torque ON/OFF. Writing ‘1’ to this address will turn on the Torque and all Data in the EEPROM area will be protected.

Value Description

0(Default) Turn off the torque

1 Turn on the torque and lock EEPROM area

NOTE : Present Position(132) can be reset when Operating Mode(11) and Torque Enable(64) are updated. For more details, please refer to the Homing Offset(20) and Present Position(132).

2. 4. 20. LED(65)
Turn on or turn off the LED on Dynamixel.

Bit Description

0(Default) Turn OFF the LED

1 Turn ON the LED

NOTE : The LED indicates present status of the device.

Status LED Representation

Booting LED flickers once

Factory Reset LED flickers 4 times

Alarm LED flickers

Boot Mode LED On

2. 4. 21. Status Return Level(68)

This value decides how to return Status Packet when Dynamixel receives an Instruction Packet.

Value Responding Instructions Description

0 PING Instruction Status Packet will not be returned for all Instructions

PING Instruction
1 Status Packet will be returned only for READ Instruction
READ Instruction

2 All Instructions Status Packet will be returned for all Instructions

NOTE : If the ID of Instruction Packet is set to Broad Cast ID(0xFE), Status Packet will not be returned for READ and WRITE Instructions regardless of Status Return Level. For more details, please refer to
the Status Packet section for Protocol 1.0 or Protocol 2.0.

2. 4. 22. Registered Instruction(69)

Value Description

0 REG_WRITE instruction is not received

1 REG_WRITE instruction is received

NOTE : If ACTION instruction is executed, the value will be changed to 0.

2. 4. 23. Hardware Error Status(70)

This value indicates hardware error status. The Dynamixel can protect itself by detecting dangerous situations that could occur during the operation.
Each Bit is inclusively processed with the ‘OR’ logic, therefore, multiple options can be generated.
For instance, when ‘0x05’ (binary : 00000101) is defined in Shutdown(63), Dynamixel can detect both Input Voltage Error(binary : 00000001) and Overheating Error(binary : 00000100).
If those errors are detected, Torque Enable(64) is cleared to ‘0’ and the motor output becomes 0[%].
REBOOT is the only method to reset Torque Enable(64) to ‘1’(Torque ON) after the shutdown.
The followings are detectable situations.

Bit Item Description

Bit 7 - Unused, Always ‘0’

Bit 6 - Unused, Always ‘0’

Bit 5 Overload Error(default) Detect persistent load that exceeds maximum output

Bit 4 Electrical Shock Error(default) Detect electric shock on the circuit or insufficient power to operate the motor

Bit 3 Motor Encoder Error Detect malfunction of the motor encoder

Bit 2 OverHeating Error(default) Detect internal temperature exceeds the configured operating temperature

Bit 1 - Unused, Always ‘0’

Bit 0 Input Voltage Error Detect input voltage exceeds the configured operating voltage

NOTE : If Shutdown occurs, use below method to reboot Dynamixels.

1. H/W REBOOT : Turn off the power and turn on again
2. S/W REBOOT : Transmit REBOOT Instruction (For more details, please refer to the Reboot section of Protocol e-Manual.)

NOTE : If Shutdown occurs, LED will flicker every second.(Firmware v41 or above)

2. 4. 24. Velocity PI Gain(76, 78)

These values indicate Gains of Velocity Control Mode. Gains of DYNAMIXEL’s internal controller can be calculated from Gains of the Control Table as shown below. Velocity P Gain of
DYNAMIXEL’s internal controller is abbreviated to KVP and that of the Control Table is abbreviated to KVP(TBL).

Controller Gain Conversion Equations Range Description

Velocity I Gain(76) KVI KVI = KVI(TBL) / 65,536 0 ~ 16,383 I Gain

Velocity P Gain(78) KVP KVP = KVP(TBL) / 128 0 ~ 16,383 P Gain

Below figure is a block diagram describing the velocity controller in Velocity Control Mode. When the instruction transmitted from the user is received by DYNAMIXEL, it takes following steps
until driving the horn.
1. An Instruction from the user is transmitted via DYNAMIXEL bus, then registered to Goal Velocity(104).
2. Goal Velocity(104) is converted to desired velocity trajectory by Profile Acceleration(108).
3. The desired velocity trajectory is stored at Velocity Trajectory(136).
4. PI controller calculates PWM output for the motor based on the desired velocity trajectory.
5. Goal PWM(100) sets a limit on the calculated PWM output and decides the final PWM value.
6. The final PWM value is applied to the motor through an Inverter, and the horn of DYNAMIXEL is driven.
7. Results are stored at Present Position(132), Present Velocity(128), Present PWM(124) and Present Current(126).

NOTE : Ka stands for Anti-windup Gain and β is a conversion coefficient of position and velocity that cannot be modified by users. For more details about the PID controller, please refer to the PID Controller
at wikipedia.

2. 4. 25. Position PID Gain(80, 82, 84), Feedforward 1st/2nd Gains(88, 90)
These Gains are used in Position Control Mode and Extended Position Control Mode. Gains of DYNAMIXEL’s internal controller can be calculated from Gains of the Control Table as shown
below. The constant in each equations include sampling time. Position P Gain of DYNAMIXEL’s internal controller is abbreviated to KPP and that of the Control Table is abbreviated to
KPP(TBL).

Controller Gain Conversion Equations Range Description

Position D Gain(80) KPD KPD = KPD(TBL) / 16 0 ~ 16,383 D Gain

Position I Gain(82) KPI KPI = KPI(TBL) / 65,536 0 ~ 16,383 I Gain

Position P Gain(84) KPP KPP = KPP(TBL) / 128 0 ~ 16,383 P Gain

Feedforward 2nd Gain(88) KFF2nd KFF2nd(TBL) / 4 0 ~ 16,383 Feedforward Acceleration Gain

Feedforward 1st Gain(90) KFF1st KFF1st(TBL) / 4 0 ~ 16,383 Feedforward Velocity Gain

Below figure is a block diagram describing the position controller in Position Control Mode and Extended Position Control Mode. When the instruction from the user is received by
DYNAMIXEL, it takes following steps until driving the horn.
1. An Instruction from the user is transmitted via DYNAMIXEL bus, then registered to Goal Position(116).
2. Goal Position(116) is converted to desired position trajectory and desired velocity trajectory by Profile Velocity(112) and Profile Acceleration(108).
3. The desired position trajectory and desired velocity trajectory is stored at Position Trajectory(140) and Velocity Trajectory(136) respectively.
4. Feedforward and PID controller calculate PWM output for the motor based on desired trajectories.
5. Goal PWM(100) sets a limit on the calculated PWM output and decides the final PWM value.
6. The final PWM value is applied to the motor through an Inverter, and the horn of DYNAMIXEL is driven.
7. Results are stored at Present Position(132), Present Velocity(128), Present PWM(124) and Present Current(126).

NOTE : In case of PWM Control Mode, both PID controller and Feedforward controller are deactivated while Goal PWM(100) value is directly controlling the motor through an Inverter. In this manner, users
can directly control the supplying voltage to the motor.

NOTE : Ka is an Anti-windup Gain that cannot be modified by users.

For more details about the PID controller and Feedforward controller, please refer to the PID Controller and Feed Forward.

Below figure is a block diagram describing the current-based position controller in Current-based Position Control Mode. As Current-based Position Control Mode is quite similar to Position
Control Mode, differences will be focused in the following steps. The differences are highlighted with a green marker in the block diagram as well.
1. Feedforward and PID controller calculates desired current based on desired trajectory.
2. Goal Current(102) decides the final desired current by setting a limit on the calculated desired current.
3. Current controller calculates PWM output for the motor based on the final desired current.
4. Goal PWM(100) sets a limit on the calculated PWM output and decides the final PWM value.
5. The final PWM value is applied to the motor through an Inverter, and the horn of DYNAMIXEL is driven.
6. Results are stored at Present Position(132), Present Velocity(128), Present PWM(124) and Present Current(126).

NOTE : Ka is an Anti-windup Gain that cannot be modified by users.

2. 4. 26. Bus Watchdog(98)

Bus Watchdog (98) is available from firmware v38. It is a safety device (Fail-safe) that stops the DYNAMIXEL if the communication between the controller and DYNAMIXEL communication
(RS485, TTL) is disconnected due to an unspecified error. Communication is defined as all the Instruction Packet in the DYNAMIXEL Protocol.

Values Description

Unit 20[ms] -

Range 0 Deactivate Bus Watchdog Function, Clear Bus Watchdog Error

Range 1 ~ 127 Activate Bus Watchdog

Range -1 Bus Watchdog Error Status

The Bus Watchdog function monitors the communication interval (time) between the controller and DYNAMIXEL when Torque Enable(64) is ‘1’. If the measured communication interval
(time) is larger than Bus Watchdog(98), the DYNAMIXEL will stop. Bus Watchdog(98) will be changed to ‘-1’ (Bus Watchdog Error). If the Bus Watchdog Error screen appears, the Goal
Value (Goal PWM(100), Goal Current(102), Goal Velocity(104), Goal Position(116)) will be changed to read-only-access. Therefore, when a new value is written to the Goal Value, a Range
Error will be returned via the Status packet. If the value of Bus Watchdog(98) is changed to ‘0’, Bus Watchdog Error will be cleared.

NOTE : For details of Range Error, please refer to the protocol of the e-Manual.

The following are examples of the operation of the Bus Watchdog function.
1. After setting the Operating Mode(11) to speed control mode, change the Torque Enable(64) to ‘1’.
2. If ‘50’ is written in the Goal Velocity(104), the DYNAMIXEL will rotate in CCW direction.
3. Change the value of Bus Watchdog(98) to ‘100’ (2,000 [ms]). (Activate Bus Watchdog Function)
4. If no instruction packet is received for 2,000 [ms], the DYNAMIXEL will stop. When it stops, the Profile Acceleration(108) and Profile Velocity(112) are applied as ‘0’.
5. The value of Bus Watchdog(98) changes to ‘-1’ (Bus Watchdog Error). At this time, the access to the Goal Value will be changed to read-only.
6. If ‘150’ is written to the Goal Velocity(104), Range Error will be returned via Status Packet.
7. If the value of Bus Watchdog(98) is changed to ‘0’, Bus Watchdog Error will be cleared.
8. If “150” is written in the Goal Velocity(104), the DYNAMIXEL will rotate in CCW direction.

2. 4. 27. Goal PWM(100)

In case of PWM Control Mode, both PID controller and Feedforward controller are deactivated while Goal PWM(100) value is directly controlling the motor through an Inverter. In other
control modes, this value is used to limit PWM value. This value cannot exceed PWM Limit(36). Please refer to the Gain section in order to see how Goal PWM(100) affects to different
control modes.

Range Description

-PWM Limit(36) ~ PWM Limit(36) Initial Value of PWM Limit(36) : ‘885’

2. 4. 28. Goal Current(102)

In case of Torque Control Mode, Goal Current(102) can be used to set a desired current. This value sets a limit to current in Current-based Position Control mode. This value cannot exceed
Current Limit(38).

Unit Value Range

about 2.69[mA] -Current Limit(38) ~ Current Limit(38)

NOTE : Applying high current to the motor for long period of time might damage the motor.

2. 4. 29. Goal Velocity(104)

In case of Velocity Control Mode, Goal Velocity(104) can be used to set a desired velocity. This value cannot exceed Velocity Limit(44). For now, Goal Velocity(104) is used for desired
velocity, but this value is not used to limit the velocity.

Unit Value Range

0.229 rpm -Velocity Limit(44) ~ Velocity Limit(44)

NOTE : The maximum velocity and maximum torque of DYNAMIXEL is affected by supplying voltage.
Therefore, if supplying voltage changes, so does the maximum velocity. This manual complies with recommended supply voltage(12[V]).

NOTE : If Profile Acceleration(108) and Goal Velocity(104) are modified simultaneously, modified Profile Acceleration(108) will be used to process Goal Velocity(104).

2. 4. 30. Profile Acceleration(108)

If Velocity-based Profile is selected for Drive Mode(10), Profile Acceleration(108) sets acceleration of the Profile.
If Time-based Profile is selected for Drive Mode(10), Profile Acceleration(108) sets accelerating time of the Profile.
Profile Acceleration(108) is applied in all control mode except Current Control Mode.
Please refer to Profile Velocity(112) for more details.

Velocity-based Profile Values Description

Unit 214.577 [rev/min2] Sets acceleration of the Profile

Range 0 ~ 32767 ‘0’ stands for an infinite acceleration

Time-based Profile Values Description

Unit 1 [msec] Sets accelerating time of the Profile

‘0’ stands for an infinite accelerating time(‘0 [msec]’).

Range 0 ~ 32737
Profile Acceleration(108) will not exceed 50% of Profile Velocity(112) value.

NOTE : Time-based Profile is available from the firmware version 42.

2. 4. 31. Profile Velocity(112)

If Velocity-based Profile is selected for Drive Mode(10), Profile Velocity(112) sets the maximum velocity of the Profile.
If Time-based Profile is selected for Drive Mode(10), Profile Velocity(112) sets the time span for the Profile.
Profile Velocity(112) is applied only in Position Control Mode and Extended Position Control Mode.

NOTE: Velocity Control Mode only uses Profile Acceleration(108) without Profile Velocity(112).

Velocity-based Profile Values Description

Unit 0.229 [rev/min] Sets velocity of the Profile

Range 0 ~ 32767 ‘0’ stands for an infinite velocity

Time-based Profile Values Description

Unit 1 [msec] Sets the time span for the Profile

‘0’ stands for an infinite velocity.

Range 0 ~ 32737
Profile Acceleration(108) will not exceed 50% of Profile Velocity(112) value.

NOTE : Time-based Profile is available from the firmware version 42.

The Profile is an acceleration/deceleration control method to reduce vibration, noise and load of the motor by controlling dramatically changing velocity and acceleration.
It is also called Velocity Profile as it controls acceleration and deceleration based on velocity.
DYNAMIXEL provides 3 different types of Profile.
The following explains 3 Profiles.
Profiles are usually selected by a combination of Profile Velocity(112) and Profile Acceleration(108).

When given Goal Position(116), Dynamixel’s profile creates desired velocity trajectory based on present velocity(initial velocity of the Profile).
When Dynamixel receives updated desired position from a new Goal Position(116) while it is moving toward the previous Goal Position(116), velocity smoothly varies for the new desired
velocity trajectory.
Maintaining velocity continuity while updating desired velocity trajectory is called Velocity Override.
For a simple calculation, let’s assume that the initial velocity of the Profile is ‘0’.
The following explains how Profile processes Goal Position(116) instruction in Position Control mode, Extended Position Control Mode, Current-based Position Control Mode.
1. An Instruction from the user is transmitted via Dynamixel bus, then registered to Goal Position(116) (If Velocity-based Profile is selected).
2. Acceleration time(t1) is calculated from Profile Velocity(112) and Profile Acceleration(108).
3. Types of Profile is decided based on Profile Velocity(112), Profile Acceleration(108) and total travel distance(ΔPos, the distance difference between desired position and present position).
4. Selected Profile type is stored at Moving Status(123).(Refer to the Moving Status(123))
5. Dynamixel is driven by the calculated desired trajectory from Profile.
6. desired velocity trajectory and desired position trajectory from Profile are stored at Velocity Trajectory(136) and Position Trajectory(140) respectively.

Condition Types of Profile

Profile not used

VPRFL(112) = 0
(Step Instruction)

(VPRFL(112) ≠ 0) & (APRF(108) = 0) Rectangular Profile

(VPRFL(112) ≠ 0) & (APRF(108) ≠ 0) Trapezoidal Profile

NOTE : Velocity Control Mode only uses Profile Acceleration(108). Step and Trapezoidal Profiles are supported. Velocity Override are supported as well. Acceleration time(t1) can be calculated as below
equation.
Velocity-based Profile : t1 = 64 * {Goal Velocity(104) / Profile Acceleration(108)}
Time-based Profile : t1 = Profile Acceleration(108)

NOTE : If Time-based Profile is selected, Profile Velocity(112) is used to set the time span of the Profile(t3), while Profile Acceleration(108) sets accelerating time(t1) in millisecond[ms]. Profile
Acceleration(108) will not exceed 50% of Profile Velocity(112) value.

2. 4. 32. Goal Position(116)

Desired position can be set with Goal Position(116). From the front view of Dynamixels, CCW is an increasing direction whereas CW is a decreasing direction. The way to reaching Goal
Position(116) is differ by 4 Profiles provided by Dynamixels. Please refer to the Profile Velocity(112) for more details.

Mode Values Description

Position Control Mode Min Position Limit(52) ~ Max Position Limit(48) Initial Value : 0 ~ 4,095

Extended Position Control Mode -1,048,575 ~ 1,048,575 -256[rev] ~ 256[rev]

Current-based Position Control Mode -1,048,575 ~ 1,048,575 -256[rev] ~ 256[rev]

Degree Conversion Constant Description

0.088°/Value 1[rev] : 0 ~ 4,095

NOTE : Profile Velocity(112) and Profile Acceleration(108) are applied in below cases:
In Position Control Mode, Profile Velocity(112) and Profile Acceleration(108) are used to create a new profile when Goal Position(116) is updated.
In Velocity Control Mode, Profile Acceleration(108) is used to create a new profile when Goal Velocity(104) is updated.

2. 4. 33. Realtime Tick(120)

This value indicates Dynamixel’s time.

Unit Value Range Description

1 ms 0 ~ 32,767 The value resets to ‘0’ when it exceeds 32,767

2. 4. 34. Moving(122)
This value indicates whether Dynamixel is in motion or not.
If absolute value of Present Velocity(128) is greater than Moving Threshold(24), Moving(122) is set to ‘1’.
Otherwise, it will be cleared to ‘0’.
However, this value will always be set to ‘1’ regardless of Present Velocity(128) while Profile is in progress with Goal Position(116) instruction.

Value Description

0 Movement is not detected

1 Movement is detected, or Profile is in progress(Goal Position(116) instruction is being processed)

2. 4. 35. Moving Status(123)

This one byte data provides additional information about the movement.
Following Error(0x08) and In-Position(0x01) are available under Position Control Mode, Extended Position Control Mode, Current-based Position Control Mode.

Bit Value Information Description

Bit 7 X - Reserved

Bit 6 X - Reserved

11 11 : Trapezoidal Profile
10 10 : Triangular Profile
Bit [5:4] Velocity Profile
01 01 : Rectangular Profile
00 00 : Profile not used(Step)

DYNAMIXEL is following the desired position trajectory

Bit 3 0 or 1 Following Error 0 : Following
1 : Not following

Bit 2 X - Reserved

Profile is in progress with Goal Position(116) instruction

Bit 1 0 or 1 Profile Ongoing 0 : Not in progress
1 : In progress

DYNAMIXEL has arrived to the desired position

Bit 0 0 or 1 In-Position 0 : Not arrived
1 : Arrived

NOTE : Triangular velocity profile is configured when Rectangular velocity profile cannot reach to the Profile Velocity(112).

NOTE : In-Position bit will be set when the positional deviation is smaller than a predefined value under Position related control modes.

2. 4. 36. Present PWM(124)

This value indicates current PWM. For more details, please refer to the Goal PWM(100).

2. 4. 37. Present Current(126)

This value indicates current Current. For more details, please refer to the Goal Current(102).

2. 4. 38. Present Velocity(128)

This value indicates current Velocity. For more details, please refer to the Goal Velocity(104).

2. 4. 39. Present Position(132)

This value indicates present Position. For more details, please refer to the Goal Position(116).

NOTE : Present Position(132) represents 4 byte continuous range(-2,147,483,648 ~ 2,147,483,647) when Torque is turned off regardless of Operating Mode(11). However, Present Position(132) will be
reset in those cases:
1. Present Position(132) is reset with the value within 1 rev (0 ~ 4,095) when Operating Mode(11) is changed to Position Control Mode.
2. Present Position(132) is reset with the value within 1 rev (0 ~ 4,095) when Torque is turned on in Position Control Mode.
Reset Present Position(132) value can be affected by Homing Offset(20).

2. 4. 40. Velocity Trajectory(136)

This is a desired velocity trajectory created by Profile. Operating method can be changed based on control mode. For more details, please refer to the Profile Velocity(112).
1. Velocity Control Mode : When Profile reaches to the endpoint, Velocity Trajectory(136) becomes equal to Goal Velocity(104).
2. Position Control Mode, Extended Position Control Mode, Current-based Position Control Mode : Velocity Trajectory is used to create Position Trajectory(140). When Profile
reaches to an endpoint, Velocity Trajectory(136) is cleared to ‘0’.

2. 4. 41. Position Trajectory(140)

This is a desired position trajectory created by Profile.
This value is only used in Position Control Mode, Extended Position Control Mode and Current-based Position Control Mode.
For more details, please refer to the Profile Velocity(112).

2. 4. 42. Present Input Voltage(144)

This value indicates present voltage that is being supplied. For more details, please refer to the Max/Min Voltage Limit(32, 34).

2. 4. 43. Present Temperature(146)

This value indicates internal temperature of Dynamixel. For more details, please refer to the Temperature Limit(31).

2. 4. 44. Indirect Address, Indirect Data

Indirect Address and Indirect Data are useful when accessing two remote addresses in the Control Table as sequential addresses. Sequential addresses increase Instruction Packet
efficiency. Addresses that can be defined as Indirect Address is limited to RAM area(Address 64 ~ 661). If specific address is allocated to Indirect Address, Indirect Address inherits features
and properties of the Data from the specific Address. Property includes Size(Byte length), value range, and Access property(Read Only, Read/Write). For instance, allocating 65(Address of
LED) to Indirect Address 1(168), Indirect Data 1(224) can perform exactly same as LED(65).
Example 1 Allocating Size 1 byte LED(65) to Indirect Data 1(224).
1. Indirect Address 1(168) : change the value to ‘65’ which is the address of LED.
2. Set Indirect Data 1(224) to ‘1’ : LED(65) also becomes ‘1’ and LED is turned on.
3. Set Indirect Data 1(224) to ‘0’ : LED(65) also becomes ‘0’ and LED is turned off.
Example 2 Allocating Size 4 byte Goal Position(116) to Indirect Data 2(225), 4 sequential bytes have to be allocated.
1. Indirect Address 2(170) : change the value to ‘116’ which is the first address of Goal Position.
2. Indirect Address 3(172) : change the value to ‘117’ which is the second address of Goal Position.
3. Indirect Address 4(174) : change the value to ‘118’ which is the third address of Goal Position.
4. Indirect Address 5(176) : change the value to ‘119’ which is the fourth address of Goal Position.
5. Set 4 byte value ‘1,024’ to Indirect Data 2 : Goal Position(116) also becomes ‘1024’ and Dynamixel moves.

Indirect Address Range Description

64 ~ 661 EEPROM address can’t be assigned to Indirect Address

NOTE : In order to allocate Data in the Control Table longer than 2[byte] to Indirect Address, all address must be allocated to Indirect Address like the above Example 2.

NOTE : Indirect Address 29 ~ 56 and Indirect Data 29 ~ 56 can only be accessed with Protocol 2.0.

3. How to Assemble

3. 1. Wiring through Back Case

CAUTION : Dynamixel X-Series cable assembly through hollow case

Organize the entangled cable before assembling the back case.
Do not assemble the back case with entangled cable. The entangled cable can be squashed by the case and cause communication error.

3. 2. Option Frame Assembly

4. Maintenance

4. 1. Horn and Gear Replacement

The horn is installed on the front wheel gear serration of the DYNAMIXEL whereas the bearing set is installed on the back.

4. 1. 1. Installing the Horn

When installing horn, carefully match the align markings on the horn and the wheel gear serration.

Once alignment is properly done, gently push the center of the horn toward the actuator.

4. 1. 2. Gear Replacement
You may need to replace the internal gear set when gears are worn out or damaged. Please follow the gear replacement instruction video.

Gear Replacement Procedure for DYNAMIXEL XH430 & XM430

5. Reference

NOTE
Compatibility Guide
Harness Compatibility

5. 1. Certifications
Please inquire us for information regarding unlisted certifications.

5. 1. 1. FCC

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

WARNING
Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

5. 2. Quick Start

5. 2. 0. 1. Prerequisites
Power supply to DYNAMIXEL(12V SMPS / Controllers)
PC with Windows or OSX
Connection between PC and DYNAMIXEL (U2D2, USB2Dynamixel or Micro USB cable)

5. 2. 0. 2. R+ Manager
In order to change settings of DYNAMIXEL, R+ Manager 1.0 or R+ Manager 2.0 must be installed on your system.
You can also use Dynamixel SDK or Dynamixel Workbench.

5. 3. Connector Information

Item TTL RS-485

1 GND
1 GND
2 VDD
Pinout 2 VDD
3 DATA+
3 DATA
4 DATA-

Diagram

Housing

JST EHR-04
JST EHR-03

PCB Header

JST B3B-EH-A JST B4B-EH-A

Crimp Terminal JST SEH-001T-P0.6 JST SEH-001T-P0.6

Wire Gauge 21 AWG 21 AWG

WARNING: Check the pinout! The pinout of Dynamixel can differ from the pinout of connector manufacturer.

5. 4. Communication Circuit
To control the Dynamixel actuators, the main controller needs to convert its UART signals to the half duplex type. The recommended circuit diagram for this is shown below.

5. 4. 1. TTL Communication

5. 4. 2. RS-485 Communication

The power of Dynamixel is supplied via Pin1(-), Pin2(+).

(The above circuit is built into Dynamixel-only controller.)
In the above circuit diagram, the direction of data signal of TxD and RxD in the TTL Level is determined according to the level of DIRECTION 485 as follows:
In case of DIRECTION485 Level = High: The signal of TxD is output to D+ and D-
In case of DIRECTION485 Level = Low: The signal of D+ and D- is output to RxD

WARNING: Check the pinout! The pinout of Dynamixel can differ from the pinout of connector manufacturer.

5. 5. Drawings
Download X_430_idle_ref.pdf
Download X-430_idle_ref.dwg
Download x-430_idle.stp

Please also checkout ROBOTIS Download Center for software applications, 3D/2D CAD, and other useful resources!

© 2019 ROBOTIS. Powered by Jekyll & Minimal Mistakes.