MA0303-A

USER’S GUIDE 2747

About This Manual
∑ Button operations are indicated using the letters shown
in the illustration.
∑ Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.

General Guide
∑ Press C to change from mode to mode. After you perform an operation (except for
B) in any mode, pressing C returns to the Timekeeping Mode.
∑ In any mode, press B to illuminate the display.

Timekeeping Mode Telememo Mode World Time Mode Alarm Mode Countdown Timer Stopwatch Mode Hand Setting Mode
Mode

Press C.

Timekeeping
This watch features separate digital and analog timekeeping. The procedures for To toggle between 12-hour and 24-hour timekeeping
setting the digital time and analog time are different. In the Timekeeping Mode, press D to toggle between 12-hour timekeeping (indicated
∑ In the Timekeeping Mode, press A to toggle the display between the date screen by A or P on the display), or 24-hour timekeeping.
and the time screen. ∑ With the 12-hour format, the P (PM) indicator appears on the display for times in the
range of noon to 11:59 p.m. and the A (AM) indicator appears for times in the range
Date Screen Time Screen of midnight to 11:59 a.m.
∑ With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
Seconds any indicator.
Minute hand ∑ The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
Hour hand applied in all modes.
Press A. Digital Time Daylight Saving Time (DST) Setting
Daylight Saving Time (summer time) advances the digital time setting by one hour
Day of week from Standard Time. Remember that not all countries or even local areas use Daylight
PM indicator Saving Time.
Hour : Minutes
To toggle the Timekeeping Mode digital time between DST and Standard Time
Month – Day 1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
Digital Time and Date screen.
Use the Timekeeping Mode to set and view a digital display of the current time and 2. Press C once to display the DST setting screen.
date. When setting the digital time, you can also configure settings for summer time 3. Press D to toggle between Daylight Saving Time
(Daylight Saving time or DST). (ON displayed) and Standard Time (OFF displayed).
4. Press A to exit the setting screen.
To set the digital time and date ∑ The DST indicator appears on the Timekeeping, Alarm,
1. In the Timekeeping Mode, hold down A until the and Hand Setting Mode to indicate that Daylight Saving
seconds start to flash, which indicates the setting Time is turned on.
screen.
2. Press C to move the flashing in the sequence shown Setting the Analog Time
below to select the other settings. Perform the procedure below when the time indicated by the analog hands does not
match the time of the digital display.

Seconds DST Hour Minutes To adjust the analog time

1. In the Timekeeping Mode, press C six times to enter
the Hand Setting Mode.
Day Month Year 2. Hold down A until the current digital time starts to
flash, which indicates the analog setting screen.
3. When the setting you want to change is flashing, use B and D to change it as 3. Press D to advance the analog time setting by
described below. 20 seconds.
∑ Holding down D advances the analog time setting at
Screen To do this: Do this:
high speed.
FA Reset the seconds to AA. Press D.
OFF Toggle between Daylight Saving Time (ON) Press D.
and Standard Time (OFF).
P10:08
Use D (+) and B (–).
∑ If you need to advance the analog time a long way, press D and B at the same
Change the hour or minutes.
time. This locks the high speed hand movement, so you can release the two
CAAD Change the year. buttons. High-speed hand movement continues until you press any button. It will
6-30 Change the month or day. also stop automatically after the time advances 12 hours or if an alarm (daily
alarm, Hourly Time Signal, or countdown alarm) starts to sound.
4. Press A to exit the setting screen. 4. Press A to exit the setting screen.
∑ Resetting the seconds only (without changing the hour, minute, or DST setting) ∑ To return to the Timekeeping Mode, press C.
causes the analog minute hand setting to be adjusted automatically. If you change
the hour, minute, or DST setting, you should also use the procedure under “To
adjust the analog time” to adjust the analog hands accordingly.
∑ See “Digital Time Daylight Saving Time (DST) Setting” for details about the DST
setting.
∑ Resetting the seconds toAA while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to AA without changing the minutes.
∑ The day of the week is automatically displayed in accordance with the date (year,
month, and day) settings.
∑ The year can be set in the range of 2000 to 2099.
∑ The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.