Scribd
Upload
169 views

Demagnetization of Pipe Magnetization

This document discusses methods for demagnetizing pipe that has become magnetized. It explains that using an alternating current (AC) power supply and wrapping welding leads around the pipe can effectively demagnetize it. The process involves wrapping leads around the pipe circumference to induce a circular magnetic field and then reducing the wraps and current. Wrapping leads longitudinally induces a magnetic field from one end to the other that changes polarity with AC current, further demagnetizing the pipe. While direct current (DC) can also be used, it requires manually switching polarity with each current change.

Uploaded by

thiyagusuper
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
169 views

Demagnetization of Pipe Magnetization

This document discusses methods for demagnetizing pipe that has become magnetized. It explains that using an alternating current (AC) power supply and wrapping welding leads around the pipe can effectively demagnetize it. The process involves wrapping leads around the pipe circumference to induce a circular magnetic field and then reducing the wraps and current. Wrapping leads longitudinally induces a magnetic field from one end to the other that changes polarity with AC current, further demagnetizing the pipe. While direct current (DC) can also be used, it requires manually switching polarity with each current change.

Uploaded by

thiyagusuper
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DEMAGNETIZATION OF PIPE MAGNETIZATION

you can demagnetize a piece by magnetizing it with AC.

The secret to demagnetizing a work piece is to remagnetize it with a field that


is stronger than the residual magnetic field that is giving you problems. The
residual magnetic field can be the result of machining the part secured with a
magnetic chuck, from grinding or machining the beveled edge, welding with
DC, or in some cases it can be the result of the magnetic field encircling the
earth. Remember, the earth is a huge magnet which can magnetize long
components transported in a northerly/southerly direction. This can be very
troublesome with long members such as pipe, beams, and rods.

AC power supplies can be used very effectively to demagnetize various


shapes using the "coil" or "cable wrap" technique. In the case of pipe, run
several wraps of welding lead through the length of the pipe. This induces a
circular field around the circumference of the pipe when it is energized with
AC current. Start with high current and then reduce it. Remove a wrap of
welding lead and energized the current again, starting with high current and
reducing it to low current. Clearly, if your welder only has taps to reduce the
current you will have to open the circuit each time you reduce the current. The
easiest way to make a switch for the current is to short out the "stinger" on a
piece of scrap and then break the arc before reducing the current by selecting
a lower current setting.

Once you have reduced the number of cable wraps to 1, wrap the welding
lead around the pipe several times. This will induce a longitudinal field so that
one end of the pipe is the North Pole and the other the South Pole. Using AC
current causes the polarity of the magnetic field to change many times per
second (depending of the cycles used, i.e., 60 Hz or 50Hz). Once again,
energize the circuit using high current and reduce the current. Repeat the
steps after removing a wrap of welding lead until there are no more wraps to
remove.

If performed properly, you should be able to hold a paper clip to the end of the
pipe and it should fall to the ground if the magnetic field is reduced
sufficiently.
This same procedure can be performed with DC, but it is more laborious
because you have to switch the polarity of the welding machine at the end of
each current cycle. Wrap the leads, energize with high current, reduce the
current, remove a wrap, switch the welding leads to change polarity, start with
high current moving to low current, remove a wrap and repeat. This should be
performed using approximately 30 steps, each at a lower current, fewer
wraps, and current reversals.

The sketch shows the general layout and the "make/break" switch. Remember
to start with the welding leads passing through and around the pipe to create
a circular field, followed by the welding leads wrapped around the pipe to
create a longitudinal field. The embedded sketch shows the latter.

You might also like