Scribd
Upload
15 views

Q1 Display

The document is a certificate of conformance from The Lincoln Electric Company certifying that an ER70S-6 welding electrode meets various specifications. It provides test results for the electrode including mechanical properties, operating settings used, and electrode composition.

Uploaded by

Oscar Basantes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15 views

Q1 Display

The document is a certificate of conformance from The Lincoln Electric Company certifying that an ER70S-6 welding electrode meets various specifications. It provides test results for the electrode including mechanical properties, operating settings used, and electrode composition.

Uploaded by

Oscar Basantes
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

The Lincoln Electric Company

22801 St. Clair Avenue


CERTIFICATE OF CONFORMANCE
Cleveland, Ohio 44117-1199 (APPLIES ONLY TO U.S. PRODUCTS)
Q1 Lot Number: 15391164
Product: Lincoln® ER70S-6
Classification: ER70S-6
Specification: AWS A5.18:2005, ASME SFA-5.18
Date June 25, 2013
This is to certify that the product named above and supplied on the referenced order number is of the same classification, manufacturing process, and material
requirements as the material which was used for the test that was concluded on the date shown, the results of which are shown below. All tests required by the
specifications shown for classification were performed at that time and the material tested met all requirements. It was manufactured and supplied according to
the Quality System Program of the Lincoln Electric Company, Cleveland, Ohio, U.S.A., which meets the requirements of ISO9001, NCA3800, AWS A5.01, and
other specification and Military requirements, as applicable. The Quality System Program has been approved by ASME, ABS, and VdTUV.

Operating Settings RESULTS


Electrode Size 696 1/8 1inch
Polarity DC- DC-
Shielding Gas (per AWS A5.32) 100% Ar (I1-Ar-100) 100% Ar (I1-Ar-100)
Voltage, V 16 - 19 16
Current, A 250 - 280 265
Travel Speed, cm/min (in/min) (4 - 6) 13 (5)
Pass/Layers 16/8
Preheat Temperature, °C (°F) (275 min.) 135 (275)
Interpass Temperature, °C (°F) (325 max.) 150 (300)
Postweld Heat Treatment As-welded As-welded
Mechanical properties of weld deposits
Tensile Strength, MPa (ksi) (70 min.) 590 (86)
Yield Strength, 0.2% Offset, MPa (ksi) (58 min.) 450 (65)
Elongation % 22 min. 31
Average Impact Energy (20 min.) See Note
Joules @ -29 °C (ft-lbs @ -20 °F) 446,446,450 (329,329,332)
Average Hardness, HRB Not Required 88

Electrode composition (weight %) 1/8 Electrode


Results
C 696 0.06 - 0.15 1 0.09
Mn 1.40 - 1.85 1.46
Si 0.80 - 1.15 0.87
S 0.035 max. 0.001
P 0.025 max. 0.005
Cr 0.15 max. 0.03
Ni 0.15 max. 0.01
Mo 0.15 max. 0.00
V 0.03 max. 0.00
Total Cu 0.50 max. 0.15
NOTE: One or more of the reported impact values exceeds the machine capacity (542 J or 400 ft-lbs) or is greater than its 80% capacity (434 J or 320
ft-lbs). The values reported are approximate and should not be averaged, per ASTM E23.

1. This certificate complies with the requirements of EN 10204, Type 2.2.


2. The electrode size required to be tested for this classification is 1/8 inch. All other sizes manufactured will also meet these requirements.
3. Test assembly constructed of ASTM A36 steel.
4. Radiographic Inspection: Met requirements.
5. Results below the detection limits of the instrument or lower than the precision required by the specification are reported as zero. Strength values in SI
units are reported to the nearest 10 MPa converted from actual data. Preheat and interpass temperature values in SI units are reported to the nearest
5 degrees.

June 25, 2013 June 25, 2013


Toronto Cunningham, Certification Supervisor Date Dave Fink, Manager, Compliance Date
Engineering, Consumable R&D

Page 1 of 1 Cert. No. 9150

You might also like