ICs for Audio Common Use

AN7158N
Dual 7.5W Audio Power Amplifier Circuit

■ Overview Unit : mm
The AN7158N is an integrated circuit designed for
power amplifier of 7.5W (16V, 4Ω) output with low noise 15.0±0.3 7.7±0.25 4.7±0.3
and low distortion, and it suits TV set with multi-sound. 3.6±0.2 1.0±0.5 2.7±0.4
Stereo operation is enabled due to incorporating two 12
amplifiers on one chip. 12-pin SIL package enabled com- 11

2.54
1.8R 10
pact and high-densely mounted set. 9
8

30.0±0.3
24.0±0.3
7

1.26±0.25
■ Features 6

0.7±0.1
5
• Incorporating protection circuits (surge, thermal protec- 4
tion and etc.) 3
2
• Automatic operating point stabilizer circuit 1
• Low distortion, low 1/f noise

– 0.05
+ 0.1
5.5±0.3
• Low shock noise from power ON/OFF operation

0.95±0.25

0.35
• Better channel separation
• Fewer external components 0.35±0.25

12-Lead SIP Package (HSIP012-P-0000B)

■ Block Diagram

Ch.2 Bootstrap GND

8 7 10

Shock Noise Temperature Over Voltage

Suppression Compensation Protection

Ch.2 9 Input Circuit Drive Output Circuit 11 Ch.2

Input Output

1 VCC

Ch.1 Ch.1
4 Input Circuit Drive Output Circuit 2
Input Output

Shock Noise Temperature Over Voltage

12 Suppression Compensation Protection

5 6 3
Ch.1 Bootstrap GND

This datasheet has been downloaded from http://www.digchip.com at this page

AN7158N ICs for Audio Common Use

■ Absolute Maximum Ratings (Ta= 25˚C)

Parameter Symbol Rating Unit
Supply Voltage Note 1) VCC 24 V
Supply Voltage Note 2) VCC 20 V
Supply Current ICC 4 A
Power Dissipation (Ta= 45˚C) PD 30 W
Operating Ambient Temperature Topr – 30 ~ + 75 ˚C
Storage Temperature Tstg – 55 ~ + 150 ˚C
Note 1) Without signal VCC = 24V (For non-stabilized supply)
Note 2) Operation VCC= 20V (For stabilized supply)

■ Electrical Characteristics (Ta = 25˚C)

• VCC=13.2V, RL= 4Ω, f =1kHz
Parameter Symbol Condition min. typ. max. Unit
Quiescent Circuit Current ICQ Vi = 0mV 40 70 120 mA
Voltage Gain GV Vi = 3mV 52 54 56 dB
Output Power PO THD = 10% 4.8 5.5 W
Total Harmonic Distortion THD Vi = 3mV 0.15 1 %
Output Noise Voltage Vno Rg = 10kΩ 1 3 mV
Channel Balance CB 0 1 dB
Vi = 3mV
Separation Sep. 45 50 dB
Ripple Rejection Ratio RR f = 60Hz, Rg = 600Ω 40 dB

• VCC =16V, RL= 8Ω, f =1kHz

Parameter Symbol Condition min. typ. max. Unit
Quiescent Circuit Current ICQ Vi = 0mV 40 80 140 mA
Voltage Gain GV Vi = 4mV 52 54 56 dB
THD = 10% 4 4.5 W
Output Power PO
RL = 4Ω, THD = 10% 7.5 W
Total Harmonic Distortion THD Vi = 4mV 0.1 1 %
Output Noise Voltage Vno Rg = 10kΩ 1 3 mV
Crosstalk CT Vi = 4mV, Rg = 10kΩ 45 dB

PD – Ta
40
(1) Tc = Ta
36 (2) With a 100cm2 × 3mm
Al heat sink (black)
or a 200cm2 × 2mm
32
(1) Al heat sink
(3) With a 100cm2 × 2mm
Power Dissipation PD (W)

28 Al heat sink
(4) Without heat sink
24

20
(2)
16
(3)
12

4 (4)

0
–20 0 20 40 60 80 100 120 140 160 180
Ambient Temperature Ta (˚C)
 ICs for Audio Common Use AN7158N

PO, ICQ – VCC PO, THD – Vi PO, THD – Vi

16 100 100

Output Power PO (W), Total Harmonic Distortion THD (%)

Output Power PO (W), Total Harmonic Distortion THD (%)

VCC = 13.2V VCC = 16V
THD = 10% RL = 4Ω THD RL = 8Ω
14 140 30 f = 1kHz 30 f = 1kHz
: GV ≈ 54dB THD : GV ≈ 54dB
12 120 10 : GV ≈ 46dB 10 : GV ≈ 46dB

Quiescent Circuit Current ICQ (mA)

PO (with 4, 9 (with 4, 9 Pin 82Ω)
Output Power PO (W)

Pin 82Ω)
10 RL = 3Ω 100 3 3
4Ω
8 otal 80 1 1
2-ch. T
ICQ PO
6 60 0.3 0.3
8Ω THD
4 40 0.1 0.1
PO

2 20 0.03 0.03
PO
0 0 0.01 0.01
0 4 8 12 16 20 0.1 0.3 1 3 10 30 100 0.1 0.3 1 3 10 30 100
Supply Voltage VCC (V) Input Voltage Vi (mV) Input Voltage Vi (mV)

THD, GV – f GV, THD – f PD – PO

3 1 4.0 8.0
Total Harmonic Distortion THD (%), Voltage Gain Response ,GV (dB)

Total Harmonic Distortion THD (%), Voltage Gain Response GV (dB)

Power Dissipation (Single Channel Operation) PD (W)

2 VCC = 13.2V GV
RL = 4Ω 0 f = 1kHz
3.6
1 Ta = 25˚C

Power Dissipation (Dual Operation) PD (W)

GV PO = 0.5W
0 –1
3.2 6.4
–1 –2
–2 2.8 5.6
–3
–3
–4 VCC = 16V 2.4 4.8
–4 RL = 8Ω VCC = 13.2V
–5 –5 PO = 0.5W 2.0 RL = 4Ω 4.0
: GV ≈ 54dB : GV ≈ 54dB
: GV ≈ 46dB : GV ≈ 46dB 1.6 3.2
(with 4, 9 Pin 82Ω) (with 4, 9
2.0 Pin 82Ω) 1.2 2.4
2.0 1.5 13.2V, 8Ω
1.5 0.8 1.6
1.0 9V, 4Ω
1.0
0.5 0.4 0.8
0.5 THD THD 9V, 8Ω
0 0 0 0
10 100 1k 10k 100k 10 100 1k 10k 100k 0 2 4 6 8 10
Frequency f (Hz) Frequency f (Hz) Output Power PO (W)

THD – PO Vno – Rg
100 2.0
VCC = 13.2V
RL = 4Ω V = 13.2V
50 1.8 R CC= 4Ω
f =100kHz L
30
Total Harmonic Distortion THD (%)

1.6
Output Noise Voltage Vno (mV)

: Commend Circuit
1.4 : GV ≈ 47dB (with82Ω to
10 Pin 4, 9)
1.2
5 82Ω100µF or less
3 1.0

0.8
1
0.6
0.5
0.4
0.3
0.2

0.1 0
0.01 0.1 1 10 100 10 100 1k 10k 100k
Output Power PO (W) Source Resistance Rg (Ω)
AN7158N ICs for Audio Common Use

47µF

+ –

– 2.2Ω
100µF
+

0.1µF
5 3 6 1000µF
2
+ –
Ch.1
Input 4 Ch.1
1 VCC Ch.1
1000pF 30kΩ AN7158N + 1000µF RL
–

12
+ –
Ch.2 Ch.2 100µF
9 1000µF
Input
11
+ –
1000pF 30kΩ 8 10 7
0.1µF
Ch.2
+ RL
100µF
– 2.2Ω
47µF

+ –

■ Printed Circuit Board Layout ■ Pin Descriptions

AN7158N Pin No. Pin Name Pin No. Pin Name
Output Output
1 VCC 7 Bootstrap Ch.2
– – –
1000µF

1000µF

1000µF

Ch.2 + + Ch.1 + 2 Output Ch.1 8 N.F.B Ch.2

47µF VCC
47µF
3 GND 9 Input Ch.2
– +
100µF

2.2Ω + – 4 Input Ch.1 10 GND

0.1µF

0.1µF – 5 N.F.B Ch.1 11 Output Ch.2

100µF

–
2.2

+ +
– + IN IN 6 Bootstrap Ch.1 12 Ripple Filter
1000pF 1000pF
100µF
30kΩ 30kΩ

12 11 10 9 8 7 6 5 4 3 2