PLC Interface.

匯出日期：2023-05-11
修改日期：2023-05-09
 机床产品/Machine Tool Products
–
PLC Interface.

1 CNC and PLC Interface

1.1 C Bit Interface (From PLC To CNC)
No Title Description

C000 Cycle Under auto mode, when this bit ON CNC will start to execute the NC program.
Start

C001 Feed During machining, when this flag ON, CNC will pause the execution of the NC program.
Hold

C002

C003

C004

C005

C006® X Axis Under JOG MODE, when this flag ON, machine will move in X+ direction.
JOG+

C007® X Axis (As above)

JOG -

C008® Y Axis (As above)R

JOG +

C009® Y Axis (As above)

JOG -

C010® Z Axis (As above)

JOG+

C011® Z Axis (As above)

JOG -

C012® C(6th) (As above)

Axis
JOG +

CNC and PLC Interface – 2

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C013® C(6th) (As above)

Axis
JOG -

C014

C015 M30 This Bit is valid only when Pr732 is set to 1. When this Bit is ON, main program does not
support execute Reset after M30 is executed. Instead, like M99 returns to the program initial
progra position, then continues executing machining.
m
Notifications（While Pr732 set to 1）：
rewind
1. When M30 is executed, M code content description is updated in R1/R616/R620/R624.
a. If C15 ON and Pr3804 part count M code number is 30, only when M30 is
executed, each path will update the M code content to 30 in R1/R616/R620/R624
respectively.
b. If C15 OFF, regardless of the Pr3804 part count M code number, when M30 is
executed, each path will update the M code content to 30 in R1/R616/R620/R624
respectively.
2. Effective vision：10.116.54, 10.117.54

C016 X Axis Select MPG to control X axis, when this FLAG is ON, controller will input as MPG and drive
MPG the X-axis to move relative displacement.
Selectio
n

C017 Y Axis (As above)

MPG
Selectio
n

C018 Z Axis (As above)

MPG
Selectio
n

C019 C(6th) (As above)

Axis
MPG
Selectio
n

CNC and PLC Interface – 3

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C020 MPG 1. In auto mode (Auto or MDI), when this Bit ON and cycle start, the machine axial moving
Simulati speed determined by the MPG rotation speed and the current G01 override. The faster
on MPG is rotated, the faster the machine moves; when MPG stops, the machine also
stopped. It is suitable for trial machining.
2. As mentioned above, "determined by current G01 override" means that even when the
MPG is rotated under rapid traverse G00 block, and the rapid traverse feedrate (R18) is
zero, machine will still move.
3. When using MPG simulation at G00 or G53 block, the maximum feedrate will be limited
to the last G00 moving speed multiplied by 37.5% of the G01 override.
4. When using MPG simulation, the number of lines/single blocks to be reversed is limited.
As for the number of lines/single blocks can be reversed, it depends on how the NC
code is written.

C021 Tool When this function is triggered, the system will automatically pause (Feedhold). After the
Withdra machine stops, the tool will retract according to the tool retraction position set by G10.6
w and feedrate override.

C022

C023 Rapid Press this button under CON JOG mode, the machine movement speed changes from the
Travers JOG SPEED to RAPID SPEED(G00) , and enable the panel RAPID OVERRIDE.
e

C024

C025 Set X To set the axial machine coordinates, the set value is determined by R38.
Axis
Restrictions:
Machine
Position Do not use C025～ and C230～ to set machine position when machining.
Compatibility:
Version 10.118.70E, 10.118.74 or befoe
Can use C025～and C230～ to set machine position when machining.
Version 10.118.70F, 10.118.75 or later
Using C025～ and C230～ to set machine position when machining, OP-033 alarm will be
issued.

C026 Set Y (As above)

Axis
Machine
Position

CNC and PLC Interface – 4

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C027 Set Z (As above)

Axis
Machine
Position

C028 Set (As above)

C(6th)
Axis
Machine

Position

C029

C030

C031 X Axis The axial trips from control mode and enters feedback monitoring mode. At this moment,
MANUAL controller can no longer send commands to the axis. If the axis moves due to external force,
CONTR the HMI displayed coordinates will also be updated.
OL
Serial axis, if you need to SERVO_OFF certain axis, you can use this Cbit to SERVO OFF the
serial axis.
Notification:
When the axis is switched back to the control mode from the feedback monitoring mode, if
machine is still moving, will cause zero speed check fails (Pr901~), system will issue
MOT-020/MOT-021 alarm, and at this moment axial needs to re-do homing.

C032 Y Axis (As above)

MANUAL
CONTR
OL

C033 Z Axis (As above)

MANUAL
CONTR
OL

C034 C(6th) (As above)

Axis
MANUAL
CONTR
OL

CNC and PLC Interface – 5

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C035 Absolut If any manual displacement (by Jog, MPG, PLC axis...) requires to be preserved during
e Feedhold state, upper edge trigger this C-BIT before the program started. In this case, the
Position amount of displacement of all axis will be synchronized to MPG offset, the program
Sync. coordinates will resume to state before feedhold. And once program starts, the machining
path will always retain this amount of displacement.
Restrictions:
This function is invalid when BIT triggered during machining, tool retract function
executing or O888801 executing.
Compatibility: Version 10.114.50G ~ 10.116.12 or later
Between Version 10.114.50G~10.116.12, when using upper edge triggers this BIT, the main
system path will perform a coordinate synchronization. This BIT has no effect in earlier
versions.

C036 Emerge When the Emergency Stop button is pressed, LADDER should triggers this FLAG and CNC
ncy stops all the movement of the machine and enters NOT READY state. Until the E-stop
Stop button is released, this FLAG is disabled and CNC generate the REST command and return
to the READY state.

C037 External • Send the RESET command to the CNC from external device.
Reset • In 10.118.40 and later version, when Pr741 is set to 1, the reset range is not including
the axis group of independent operation.

C038 M.S.T When LADEER executes M, S, T CODE, CNC will wait for this FLAG ON to start the execution
Finish of the next BLOCK. Therefore, after LADDER executed M, S, T CODE, this FLAG needs to be
ON.

C039 Part • When this BIT is ON, the part count M-code of the main program will be paused (B-
count STOP).
M-code • If the part count M-code of the main program is M99, CNC will only be paused (M-99)
stop when the M99 with the smallest path number is read.
request • 10.118.29Z, 10.118.40F, 10.118.44 and later: The request is invalid in MDI mode.
Relative reference: Parameter3804, S35

C040 Single When the machining program is executed under this FLAG ON, a block will be executed and
Block then enter the single block stop. It is necessary to Cycle Start again before executing the
next single block (Block).
(Please turn ON C40 before machining. If you turn ON C40 during machining, it may
requires several blocks to decelerate to zero before block stop. If it is required to check the
program during machining, it is recommended to stop with the MPG simulation C20 or M00.

CNC and PLC Interface – 6

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C041 Optiona When the machining program is executed while this FLAG ON, if the jump character '/' is
l Skip written in the program, the line will be skipped and the next block will be executed directly.
(This function cannot support partial syntax. When an unsupported syntax is encountered,
a COM alarm will be issued.)

C042 Dry Run When this FLAG is ON, the execution of G CODE is performed at an dry run speed.
G01 dry run speed is up to 500% of the feedrate command in the program. The dry run
speed is limited by Pr405 and Pr621~. Under this mode, G01 override is valid.
G00 dry run speed is 100% of the original G00 speed.

C043 Machine When this FLAG is ON, and program is executed, the program will run but the machine will
Lock not move. It is usually used for program check.
Note: Version 10.114.45, 10.115.46B, 10.115.48 and after C43 function is cancelled.
This function enables (C43 ON) first, and sends a command to the axis, i.e. : G91G00X100.,
then axis does not move, and the remaining distance and program coordinates are
displayed normally, but the machine coordinates are not changed. The system will
synchronize the machine coordinates to the program coordinates until this function is
turned off.
If the function is enabled (C43 ON) during axial movement, the axis will not move and the
remaining distance and program coordinates will be displayed normally, but the machine
coordinates will stop when the function is activated. The system will synchronize the
machine coordinates to the program coordinates until this function is turned off.

C044 Optiona When this FLAG is ON and M01 is executed, controller will enter the FEEDHOLD state.
l Stop
When this FLAG is OFF and M01 is executed, controller will ignore M01 and continue to
execute the next BLOCK.

C045 Z Axis When this FLAG is ON, and program is executed, the program will run but the machine will
Lock not move. It is usually used for program check.
This function enables (C45 ON) first, and sends a command to the Z axis, i.e. : G91G00Z100.,
then Z axis does not move, and the remaining distance and program coordinates are
displayed normally, but the machine coordinates are not changed. The system will
synchronize the machine coordinates to the program coordinates until this function is
turned off.
If the function is enabled (C45 ON) during axial movement, the Z axis will not move and the
remaining distance and program coordinates will be displayed normally, but the machine
coordinates will stop when the function is activated. The system will synchronize the
machine coordinates to the program coordinates until this function is turned off.

CNC and PLC Interface – 7

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C046 Axis The first set of axis coupling state switches, when Pr3825 is set to non-mechanical coupling,
Couplin the actual coupling state is determined by this bit.
g When this FLAG is ON, the coupling axis enters the coupling state.
Request When this FLAG is OFF, the coupling state is disabled.
In the coupling state, when the master axis moves, the slave axis moves according to the
set ratio.

C047 Inhibit When this FLAG is ON, the system is prohibited from storing persistent data. However, the
Persist system will force to synchronize once this FLAG turns from OFF to ON.
State
Flush

C048 Wait All main system path skip the WAIT() command, and continues the look ahead in the
Functio following machining program.
n Skip
Signal

C049 Macro Interrupt signal of interrupted subprogram function. When this C Bit On, the program that
Interrup was originally executed stops immediately and calls the interrupt subprogram.
tion
Request

C050 Over The X-axis machine hardware limit, when this FLAG ON controller will automatically enter
Travel Feedhold state. Meanwhile, it will not accept the JOG command or MPG command in this
X+ direction, and can be retracted only in the opposite direction.

C051 Over (As above)

Travel
X-

C052 Over (As above)

Travel
Y+

C053 Over (As above)

Travel Y-

C054 Over (As above)

Travel
Z+

CNC and PLC Interface – 8

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C055 Over (As above)

Travel
Z-

C056 Over (As above)

Travel
C(6th)+

C057 Over (As above)

Travel
C(6th)-

C058

C059

C060 Spindle When C60 ON, the spindle running speed will be forced to run at the spindle positioning
JOG drifting speed set by Pr1721. This function is usually used for milling machine spindle tool
Mode change, calibration or automatic lathe machine tending.
C60 only affects and designate the speed of the spindle, which does not activate the
spindle rotation; therefore, it still needs to be used with C64. The spindle is originally under
C64, and follow S code command; under C64+C60, follow the Pr1721 command.

CNC and PLC Interface – 9

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C061 Spindle When C61 is ON, the spindle positioning function is executed. This function must be
Orientat equipped with position encoder on the spindle side or the gear ratio is 1:1. C61 can be
ion Stop disabled only when positioning completed; during positioning, press Reset (C37 ON) will
not interrupt the positioning action.
General Spindle
1. Pr1741 sets the speed of spindle positioning. After the spindle reaches the positioning
speed, it starts to detect the signal. Pr1751 sets the spindle positioning offset angle.
This angle is the offset angle in respect to the index signal. After replacing the motor,
encoder, or belt, this parameter must be re-calibrated; Pr1761 sets the spindle
positioning time; S61 is the spindle positioning completion signal. When C61 is ON, the
spindle will stop first and then start positioning from stationary.
2. Pr1771 is invalid after version 10.116.26A, 10.116.36I.
3. Spindle positioning angle description:

General Serial Spindle

1. Pr1791= 1~2, the positioning action is same as general spindle.
2. Pr1791= 3, the first positioning actin is same as general spindle. After the second time,
the positioning can be reached within one revolution by using the acceleration of
Pr1801 / Pr1831 / Pr1841. The positioning angle is Pr1751. Since the whole process is
position control, the controller can directly position the spindle to the set value even if
the spindle is running at high speed.
3. When the positioning is completed, S61 is ON, and the spindle angle is displayed as the
setting of "Pr1751"
4. spindle positioning angle description: same as the general spindle
Syntec Serial Spindle
1. Use the built-in spindle quick positioning function in the driver.
2. The spindle positioning angle is determined by Pr1771.
3. Syntec M2 Pr1771 will be synchronized with the driver P6-20. The rules are as follows:
a. Power on, the P6-20 of the driver is synchronized to Pr1771~Pr1776 for the first
time,

CNC and PLC Interface – 10

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

b. Afterwards, no matter modifying the controller parameters (Pr1771~Pr1776) or

the driver parameters (P6-20), it will be synchronized in both sides.
c. Syntec M3 has no P6-20 parameters, so there will be no such synchronous
action.
4. Pr1751 is invalid and must be set to 0, otherwise system issue SPD-026 alarm.
5. After positioning is completed, the spindle angle is displayed as 0 degrees.
6. Spindle positioning angle description：

Any point high speed positioning function

1. G10 L20 P0 R_ can be used to modify the positioning angle dynamically and display it
synchronously at #1610.
2. M19 C_ : The standard arbitrary point positioning function provided by the controller. It
needs to register M0019 as Macro to use. (ex. Pr3601 set as 19).
3. The actual specifications of M0019 are as follows：
a. Read the C argument and set the spindle positioning angle through G10 L20 P0
R#3. (G10 L20 detailed usage please see the development manual)
b. As above, if there is no C argument, the default angle is set by Pr1751~Pr1756,
that is, in a. #3 will be replaced by Pr1751~Pr1756.
c. After the positioning angle is determined, issue M19 to PLC for triggering C61 ON
to perform positioning. (PLC needs to cooperate with C61 ON)
4. Support positioning when the spindle is rotating clockwise (counterclockwise), that is,
directly position when C64 (C65) is ON.
5. The positioning speed and acceleration are controlled by the driver and are not
affected by the controller parameter setting.
6. After positioning is executed, the positioning angle is restored to the angle set by the
parameter.
7. For Syntec M2 spindle, the driver firmware must be updated to version 1.4.2 and above.
Operating restrictions
1. In the tapping mode, this C Bit is invalid.

CNC and PLC Interface – 11

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

2. Because the controller will synchronize the coordinates when C63 is switched, it is
recommended to use this function in the case of C63 OFF. Otherwise, the error
coordinate synchronization may cause, and the machining action is not as expected
after the positioning is completed.
Version compatibility description
1. Refer to the page "Spindle Application - Spindle Positioning (C61)".

C062® Skip When C62 is ON, the measurement escape command G31 will be recording the current
Signal mechanical position and interrupt the G31 action, then jump directly to the next block to
State continue execution. If there are multiple G31 to be triggered in the program, it is
recommended that C62 is upper triggered, preventing multiple G31 from being tripped
within the same C62_ON.

C063 Spindle For non-inverter spindle type (Pr1791~≠0, 5, 6, 7), this C BIT ON means that the spindle is
OFF switched to the position control mode. Now controller will perform mechanical coordinate
synchronization (motor feedback synchronize back to the mechanical coordinate); but
when C BIT is OFF, it means to switch back to the spindle speed control mode, and its
clockwise and counterclockwise rotation control is determined by C64/C65.
Compatibility change:
1. Version 10.116 and before, when using M Code to switch the spindle C/S axis conversion,
it is recommended that C38 in the PLC wait for S63 to ensure the correctness of the position
control mode.
2. Version 9.x and before, the position control mode can be switched without using C63, but
should follow the behavior of #1820 first turn on then turn off later to synchronize the
coordinates, in order to ensure the correctness of the mechanical coordinates.
Operating restrictions:
In tapping mode, this C Bit is invalid.

C064 Rotating For non-inverter spindle type (Pr1791~≠0, 5, 7), this signal is the spindle clockwise rotation
the command.
spindle
In order to correctly use the spindle speed arrival check function Pr1991~, even if it is a
clockwis
variable frequency spindle, this C Bit must be triggered to notify the system spindle to enter
e
the running state.
Operating restrictions:
In the tapping mode, this C Bit is invalid.

CNC and PLC Interface – 12

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C065 Rotating For non-inverter spindle type (Pr1791~≠0, 5, 7), this signal is the spindle counterclockwise
the rotation command.
spindle
In order to correctly use the spindle speed arrival check function Pr1991~, even if it is a
counter
variable frequency spindle, this C Bit must be triggered to notify the system spindle to enter
clockwis
the running state.
e
Operating restrictions:
In the tapping mode, this C Bit is invalid.

C066® X axis 1. When this signal is ON, the PLC axis movement is executed. The movement command
controll of the NC program does consider the movement of the PLC axis, that is, the coordinate
ed by synchronization between the NC axis and the PLC axis, but the movement speed of the
PLC PLC axis at this time will not be added to display on HMI.
2. When this signal is OFF, the PLC axis movement is executed. The movement command
of the NC program does not consider the movement of the PLC axis, but the movement
speed of the PLC axis will be added to display on HMI.
3. Following item 2, since this signal is OFF, the axis is not declared as PLC control.
Therefore, when mode switches, the specific axis' PLC movement will be interrupted.
4. When NC program and the PLC axis simultaneously command the same axis, the axial
command will have an additive effect, user should pay extra attention on this.
5. This signal can only be used in position control mode. If the axis is spindle, you need to
switch to position control mode to perform PLC axis.

C067® Y axis (As above)

controll
ed by
PLC

C068® Z axis (As above)

controll
ed by
PLC

C069® C (As above)

axis(6th)
controll
ed by
PLC

C070

CNC and PLC Interface – 13

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C071 Enable Under non-MPG mode, this signal is enabled (ON), and the input of the No. 1 MPG is used as
MPG an axial position command to move the corresponding axis.
No1
※ Under MPG mode, the default MPG channel is enabled, so this signal is disabled (OFF),
and the MPG signal cannot be blocked as the axial position command input.
※The channel signal can be turned off by setting the parameter Pr2021 to 0.

C072 Enable (As above)

MPG
No2

C073 Enable (As above)

MPG
No3

C074

C075

C076

C077

C078

C079 X HOME When HOME DOG signal is read from IO board, this C BIT needs to be ON, so need to add
DOG this C BIT in LADDER.

C080 Y HOME (As above)

DOG

C081 Z HOME (As above)

DOG

C082 C(6th) (As above)

HOME
DOG

CNC and PLC Interface – 14

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C083 The The third software stroke limit switch. Off: protection disabled; On: protection enabled.
third Please refer to parameters 2441~2480 for further explanation. (Version 10.116.x and after it
softwar is renamed to the third software stroke limit)
e stroke
limit
switch

C084 Relieve When the controller is powered off, and axial movement exceeds the setting range of
the Pr1021~1040 which R940 is triggered, this can be relieved by this C Bit.
excessiv
e
amount
of
movem
ent
while
power-
off
FLAG.

C085

CNC and PLC Interface – 15

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C086 CHPST Enabled Chopping function, relative parameter：Pr3951~3956，safety cautions as below;

1. Valid version: 10.118.19(Include) and before.
2. Cannot be mixed with the first path G81.1.
3. When C86 Off → On, it means the Chopping function is enabled. Chopping axis image
will move to the reference point first, and then move back and forth between up and
down vertex.
4. When C86 On → Off, it means the Chopping function is , and the Chopping axis will
move to the lower vertex first and then back to the R point.
5. If the emergency stop (C36) is pushed during the Chopping process, the Chopping axis
will stop immediately.
6. If the controller is reset (C37) during Chopping, the Chopping axis will move back to the
specified R point coordinates before stopping.
7. When the controller has an alarm, the Chopping axis will act according to the alarm
urgency level:
a. The alarm that makes system enter Not Ready State (Servo Off), the Chopping
axis will stop immediately.
b. The alarm that stop the system from machining cycle, the Chopping axis will
move back to the specified R point coordinates before stopping.
c. The alarm does not stop the system from machining cycle, the Chopping axis
will work normally.
8. Chopping cannot be used at the RTCP mode, otherwise COR-342 alarm is issued.
9. When Chopping is in progress, the Chopping axis can no longer input other movement
commands, otherwise COR-339 alarm is issued.
a. Movement commands such as: G0, G1, G2/G3, G31, G53, and etc.
10. When Chopping is in process, the Chopping axis cannot change the coordinate data,
otherwise COR-340 alarm is issued.
a. Coordinate data such as: G54 P1~G54 P100, G92/G92.1, G10 L2, G10 L1300, G68/
G68.2/G68.3, #value(#1880~#1933, #20001~#20658), external coordinate offset,
MPG offset.
11. When the Chopping axis is in the PLC axis execution state, or as spindle, or it has been
specified by other path as the Chopping axis, COR-341 alarm will be issued.
12. Chopping axial does not support mirroring.

CNC and PLC Interface – 16

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C087 CHLD Chopping Feedhold function

Valid version: 10.118.19 (include) and before.
When C87 On → Off while in movement, the Chopping axis will stop and return to the R
point; when C87 goes from Off → On, the Chopping axis action will activate again.
While feedhold, you may change the upper and lower vertex's coordinates. There can be
different actions when you change in different timings. Below are four possible situations:
• When the upper vertex coordinates are modified, during the axial movement from the
upper vertex to the lower vertex, the axis first moves to the lower vertex and then to the
new upper vertex coordinates.
When the axis moves to the lower vertex coordinates, the servo lag compensation
function will also be canceled at the same time. When the new upper vertex is reached,
the compensation will be activated again.

• When the lower vertex coordinates are modified during the axial movement from the
upper vertex to the lower vertex, the axis first moves to the upper vertex and then to
the new lower vertex coordinates.
When the axis moves to the upper vertex coordinates, the servo lag compensation
function will also be canceled at the same time. When the new lower vertex is reached,
the compensation will be activated again.

CNC and PLC Interface – 17

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

• When the upper vertex coordinates are modified during the axial movement from the
lower vertex to the upper vertex, the axis moves to the upper vertex first, then to the
lower vertex and the new upper vertex coordinates.
When the axis moves to the lower vertex coordinates, the servo lag compensation
function will also be canceled at the same time. When the new upper vertex is reached,
the compensation will be activated again.

• When the lower vertex coordinates are modified during the axial movement from the
lower vertex to the upper vertex, the axis moves directly to the new lower vertex
coordinates after moving to the upper vertex coordinates.
When the axis moves to the upper vertex coordinates, the servo lag compensation
function will also be canceled at the same time. When the new lower vertex is reached,
the compensation will be activated again.

C088 Disable Disable the screen saver after screen saver is already activatd by on this bit. The
Screen recommended igniting time is 500ms at least.(Only available on CE system)
Saver Valid version: 10.114.53, 10.115.55, 10.114.50C

C089 Edit Prohibit edit program mode (Including MDI edit) 0: Allow program editing 1: Prohibit
inhibitio program edition.
n

C090 Progra Switch to program edit screen.

m Edit
Screen

C091 Graph Switch to graphical dialog screen.

Dialog
Screen

CNC and PLC Interface – 18

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C092 Monitor Switch to program processing monitor screen.

Screen

C093 Position Switch to Position Monitor screen

Screen

C094 Tool Switch to Tool Offset screen

Offset
Screen

C095

C096 File Switch to File Management screen

Manage
ment
Screen

C097

C098

C099

C100

C101~ Macro Mapping to the macro system variables (#6001~#6032)

C132 mappin
g
variable

C133 Axis First path switch function

Exchang
Enable axis exchange status of two axis assigned by Pr3721 & Pr3722.
e
Request
1

C134 Axis Second path switch function

Exchang
Enable axis exchange of two axis assigned by Pr3726 & Pr3727.
e
Request
2

CNC and PLC Interface – 19

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C135 Axis Third path switch function

Exchang
Enable axis exchange of two axis assigned by Pr3731 & Pr3732.
e
Request
3

C136 Axis Fourth path switch function

Exchang
Enable axis exchange of two axis assigned by Pr3736 & Pr3737.
e
Request
4

C137 Tension Two axis designated by Pr2901、Pr2902 will enter tension control state.
Control
Switch

C138

C139

C140 4th Axis The 4th axis machine positive hardware limit, when this FLAG ON controller will
OT + automatically enters Feedhold state. Meanwhile, it will not accept the JOG command or
MPG command in this direction, and can be retracted only in the opposite direction.

C141 4th Axis (As above)

OT -

C142 5th Axis (As above)

OT +

C143 5th Axis (As above)

OT -

C144 7th Axis (As above)

OT +

C145 7th Axis (As above)

OT -

C146 8th Axis (As above)

OT +

CNC and PLC Interface – 20

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C147 8th Axis (As above)

OT -

C148 9th Axis (As above)

OT +

C149 9th Axis (As above)

OT -

C150 10th Axis (As above)

OT +

C151 10th Axis (As above)

OT -

C152 11th Axis (As above)

OT +

C153 11th Axis (As above)

OT -

C154 12th Axis (As above)

OT +

C155 12th Axis (As above)

OT -

C156 13th Axis (As above)

OT +

C157 13th Axis (As above)

OT -

C158 14th Axis (As above)

OT +

C159 14th Axis (As above)

OT -

CNC and PLC Interface – 21

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C160 15th Axis (As above)

OT +

C161 15th Axis (As above)

OT -

C162 16th Axis (As above)

OT +

C163 16th Axis (As above)

OT -

C164 17th (As above)

Axis OT
+

C165 17th (As above)

Axis OT -

C166 18th (As above)

Axis OT
+

C167 18th (As above)

Axis OT -

C168

C169

C170® 4th Axis User JOG MODE, press the 4th Axis JOG+ button on the panel. When this FLAG is ON in the
JOG + LADDER, controller will move along this direction.

C171® 4th Axis (As above)

JOG -

C172® 5th Axis (As above)

JOG +

CNC and PLC Interface – 22

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C173® 5th Axis (As above)

JOG -

C174® 7th Axis (As above)

JOG +

C175® 7th Axis (As above)

JOG -

C176® 8th Axis (As above)

JOG +

C177® 8th Axis (As above)

JOG -

C178® 9th Axis (As above)

JOG +

C179® 9th JOG (As above)

-

C180® 10th Axis (As above)

JOG +

C181® 10th Axis (As above)

JOG -

C182® 11th Axis (As above)

JOG +

C183® 11th Axis (As above)

JOG -

C184® 12th Axis (As above)

JOG +

C185® 12th Axis (As above)

JOG -

CNC and PLC Interface – 23

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C186® 13th Axis (As above)

JOG +

C187® 13th Axis (As above)

JOG -

C188® 14th Axis (As above)

JOG +

C189® 14th Axis (As above)

JOG -

C190® 15th Axis (As above)

JOG +

C191® 15th Axis (As above)

JOG -

C192® 16th Axis (As above)

JOG +

C193® 16th Axis (As above)

JOG -

C194 17th (As above)

Axis
JOG +

C195 17th (As above)

Axis
JOG -

C196 18th (As above)

Axis
JOG +

C197 18th (As above)

Axis
JOG -

CNC and PLC Interface – 24

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C198

C199

C200 4th Axis When HOME DOG is read from IO board, LADDER needs to trigger this C BIT.
Home
Dog

C201 5th Axis (As above)

Home
Dog

C202 7th Axis (As above)

Home
Dog

C203 8th Axis (As above)

Home
Dog

C204 9th Axis (As above)

Home
Dog

C205 10th Axis (As above)

Home
Dog

C206 11th Axis (As above)

Home
Dog

C207 12th Axis (As above)

Home
Dog

C208 13th Axis (As above)

Home
Dog

CNC and PLC Interface – 25

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C209 14th Axis (As above)

Home
Dog

C210 15th Axis (As above)

Home
Dog

C211 16th Axis (As above)

Home
Dog

C212 17th Axis (As above)

Home
Dog

C213 18th (As above)

Axis
Home
Dog

C214

C215 4th Axis The 4th axis' axial MPG selection. When this FLAG is ON, controller will input pulse of the
MPG MPG and drive the 4th axis to move in relative displacement.
Selectio
n

C216 5th Axis (As above)

MPG
Selectio
n

C217 7th Axis (As above)

MPG
Selectio
n

C218 8th Axis (As above)

MPG
Selectio
n

CNC and PLC Interface – 26

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C219 9th Axis (As above)

MPG
Selectio
n

C220 10th Axis (As above)

MPG
Selectio
n

C221 11th Axis (As above)

MPG
Selectio
n

C222 12th Axis (As above)

MPG
Selectio
n

C223 13th Axis (As above)

MPG
Selectio
n

C224 14th Axis (As above)

MPG
Selectio
n

C225 15th Axis (As above)

MPG
Selectio
n

C226 16th Axis (As above)

MPG
Selectio
n

CNC and PLC Interface – 27

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C227 17th Axis (As above)

MPG
Selectio
n

C228 18th Axis (As above)

MPG
Selectio
n

C229

C230 Set 4th Set the axial machine coordinates, the content filled is determined by R38.
Axis Restrictions:

Machine Do not use C025～ and C230～ to set machine position when machining.
Position Compatibility:
Version 10.118.70E or befoe
Can use C025～and C230～ to set machine position when machining.
Version 10.118.70F or later
Using C025～ and C230～ to set machine position when machining, OP-033 alarm will be
issued.

C231 Set 5th (As above)

Axis

Machine
Position

C232 Set 7th (As above)

Axis

Machine
Position

C233 Set 8th (As above)

Axis

Machine
Position

CNC and PLC Interface – 28

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C234 Set 9th (As above)

Axis

Machine
Position

C235 Set 10th (As above)

Axis

Machine
Position

C236 Set 11th (As above)

Axis

Machine
Position

C237 Set 12th (As above)

Axis

Machine
Position

C238 Set 13th (As above)

Axis

Machine
Position

C239 Set 14th (As above)

Axis

Machine
Position

C240 Set 15th (As above)

Axis

Machine
Position

CNC and PLC Interface – 29

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C241 Set 16th (As above)

Axis

Machine
Position

C242 Set 17th (As above)

Axis
Machine
Position

C243 Set 18th (As above)

Axis
Machine
Position

C244

C245 4th Axis When axial trips from control mode, and enters the feedback monitoring mode. Now
MANUAL controller can no longer send commands to the axis. If the axis moves due to external force,
CONTR the coordinates on MHI will also be updated.
OL Remark:
When the axis is switched back to the control mode from the feedback monitoring mode, if
the machine is still moving, will cause zero speed check fails (Pr901~), the system will issue
a MOT-020/MOT-021 alarm, and the axis needs to redo homing.

C246 5th Axis (As above)

MANUAL
CONTR
OL

C247 7th Axis (As above)

MANUAL
CONTR
OL

C248 8th Axis (As above)

MANUAL
CONTR
OL

CNC and PLC Interface – 30

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C249 9th Axis (As above)

MANUAL
CONTR
OL

C250 10th Axis (As above)

MANUAL
CONTR
OL

C251 11th Axis (As above)

MANUAL
CONTR
OL

C252 12th Axis (As above)

MANUAL
CONTR
OL

C253 13th Axis (As above)

MANUAL
CONTR
OL

C254 14th Axis (As above)

MANUAL
CONTR
OL

C255 15th Axis (As above)

MANUAL
CONTR
OL

C256 16th Axis (As above)

MANUAL
CONTR
OL

CNC and PLC Interface – 31

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C257 17th Axis (As above)

MANUAL
CONTR
OL

C258 18th Axis (As above)

MANUAL
CONTR
OL

C259

C260® 4th axis 1. When this signal is ON, the PLC axis movement is executed. The movement command
controll of the NC program does consider the movement of the PLC axis, that is, the coordinate
ed by synchronization between the NC axis and the PLC axis, but the movement speed of the
PLC PLC axis at this time will not be added to display on HMI.
2. When this signal is OFF, the PLC axis movement is executed. The movement command
of the NC program does not consider the movement of the PLC axis, but the movement
speed of the PLC axis will be added to display on HMI.
3. Following item 2, since this signal is OFF, the axis is not declared as PLC control.
Therefore, when mode switches, the specific axis' PLC movement will be interrupted.
4. When NC program and the PLC axis simultaneously command the same axis, the axial
command will have an additive effect, user should pay extra attention on this.
5. This signal can only be used in position control mode. If the axis is spindle, you need to
switch to position control mode to perform PLC axis.

C261® 5th axis (As above)

controll
ed by
PLC

C262® 7th axis (As above)

controll
ed by
PLC

C263® 8th axis (As above)

controll
ed by
PLC

CNC and PLC Interface – 32

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C264® 9th axis (As above)

controll
ed by
PLC

C265® 10th axis (As above)

controll
ed by
PLC

C266® 11th axis (As above)

controll
ed by
PLC

C267® 12th axis (As above)

controll
ed by
PLC

C268® 13th axis (As above)

controll
ed by
PLC

C269® 14th axis (As above)

controll
ed by
PLC

C270® 15th axis (As above)

controll
ed by
PLC

C271® 16th axis (As above)

controll
ed by
PLC

CNC and PLC Interface – 33

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C272 17th axis (As above)

controll
ed by
PLC

C273 18th axis (As above)

controll
ed by
PLC

C274 Enable Under non-MPG mode, this signal is enabled (ON), and the input of the No. 4 MPG is used as
MPG an axial position command to move the corresponding axis.
No4
※ Under MPG mode, the default MPG channel is enabled, so this signal is disabled (OFF),
and the MPG signal cannot be blocked as the axial position command input.
※The channel signal can be turned off by setting the parameter Pr2024 to 0.

C275 Enable (As above)

MPG
No5

C276 Enable (As above)

MPG
No6

C277 Enable (As above)

MPG
No7

C278

C279

C280

C281

C282

C283

CNC and PLC Interface – 34

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C284

C285

C286

C287

C288

C289

C290

C291

C292

C293

C294

C295

C296

C297

C298

C299

C300 Reload The Reload ECam insertion point is modified in the R value. (For electronic cam function)
ECam

C301 Enable Enable the first group of electronic cams. When this Bit ON, the first group of electronic cam
1st will start executing, and the S Bit with same number will be ON; when this Bit is OFF, the
ECam ECam function will only be terminated until all curve paths are finished.

CNC and PLC Interface – 35

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C302 Enable 2 (As above)

nd
ECam

C303 Enable 3 (As above)

rd
ECam

C304 Enable (As above)

4th
ECam

C305 Enable (As above)

5th
ECam

C306 Enable (As above)

6th
ECam

C307 Enable (As above)

7th
ECam

C308 Enable (As above)

8th
ECam

C309

C310

C311

C312

C313

C314

C315

CNC and PLC Interface – 36

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C316

C317~
C319

C320~ For Robot kernel usage area (not customizable area)

C350 robot
kernel

C351~
C400

C401~ Standar Mapping to the standard PC keyboard scan code 1~88

C488 d
keyboar
d Scan
Code

C489 OEM Application self-defined extension keys 89-111 are user defined by individual applications.
extende
d key
Mapping to PC keyboard ALT-1

C490 Mapping to PC keyboard ALT-2

C491 Mapping to PC keyboard ALT-3

C492 Mapping to PC keyboard ALT-4

C493 Mapping to PC keyboard ALT-5

C494 Mapping to PC keyboard ALT-6

C495 Mapping to PC keyboard ALT-7

C496 Mapping to PC keyboard ALT-8

C497 Mapping to PC keyboard ALT-9

C498 Mapping to PC keyboard ALT-0

CNC and PLC Interface – 37

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

C499 Mapping to PC keyboard ALT-B

C500 Mapping to PC keyboard ALT-V

C501 Mapping to PC keyboard ALT-E

C502 Mapping to PC keyboard ALT-F

C503 Mapping to PC keyboard ALT-I

C504 Mapping to PC keyboard ALT-J

C505 Mapping to PC keyboard ALT-K

C506 Mapping to PC keyboard ALT-L

C507 Mapping to PC keyboard ALT-W

C508 Mapping to PC keyboard ALT-N

C509 Mapping to PC keyboard ALT-S

C510 Mapping to PC keyboard ALT-T

C511 Mapping to PC keyboard ALT-U

All the C bits will be read simultaneously and only the C bit with ® mark is processed at real time. Other signals will
be send to the stack after being read, then run by sequence non-simultaneously.

1.2 S Bit Interface (From CNC To PLC)

No Title Description

S000 Cycle Start During machining (BUSY status), this FLAG will be ON.
Light

S001 Feed Hold Pause Machining (FEEDHOLD status)，this FLAG will be ON.
Light

CNC and PLC Interface – 38

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S002 Block stop During single block stop (BLOCK STOP status)，this FLAG will be ON.

S003 Feedhold When this FLAG is ON，it indicates that feedhold status is prohibited now.
inhibit

S004 Rigid First spindle is on rigid tapping mode.

Tapping

S005

S006 X Axis Busy When this FLAG is ON, it indicates that the X-axis manual function (MPG/JOG/
Homing/PLC axis) is being executed, and the new manual command cannot be
accepted. When this FLAG is OFF, the X-axis is in the Idle state and is allowed to
accept new manual command.

S007 Y Axis Busy (As above)

S008 Z Axis Busy (As above)

S009 C(6th) Axis (As above)

Busy

S010

S011 2nd of When Pr3810 (activating the same block M code simultaneous execution function) is
Multiple M set to 1, and the controller executes the second M code in the same block, this FLAG
code read will be ON, and inform LADDER to execute M code, the content of M code is stored in
R2051. After the controller issues this FLAG, it will wait until the C BIT FLAG ON of M
code FIN, then starting to execute the next BLOCK.

S012 3rd of (As above, and M mode content is stored in R2052)

Multiple M
code read

S013 4th of (As above, and M mode content is stored in R2053)

Multiple M
code read

CNC and PLC Interface – 39

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S014 5th of (As above, and M mode content is stored in R2054)

Multiple M
code read

S015

S016 X Axis Home X Homing OK, X axis HOME process finished, and this FLAG will be ON. The software
OK stroke limit protection will be activated after homing completed. Therefore, in the
case that this S BIT FLAG is not ON, LADDER should write not allowed to cycle start
and give homing not complete alarm.

S017 Y Axis Home (As above)

OK

S018 Z Axis Home (As above)

OK

S019 C(6th) Axis (As above)

Home OK

S020

S021 During Tool After entering the tool retract function and leaving the original machining path, this
Withdraw FLAG will be ON; until the tool returned and repositioned to the original machining
program path, and this FLAG will be OFF.

S022 Tool deviates When system status is FeedHold or BlockStop, this FLAG will be ON after the tool
from deviates from the original path. After the tool reposition is done and return to the
reposition original path, then the FLAG will be set to OFF.
point

S023 Servo Not • Description

Ready • When all the axes(except axes in spindle mode or watch mode) of CNC
system are in servo-on state, this S bit will be off.
• When NOT all the axes(except axes in spindle mode or watch mode) of
CNC system are in servo-on state, this S bit will be on.
• Attention note
• Valid version: 10.118.24A, 10.118.25A, 10.118.28N, 10.118.37 and later.
• In 10.118.40 and later version, when Pr741 is set to 1, this status is not
including the axis of axis group of independent operation.

CNC and PLC Interface – 40

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S024

S025

S026

S027

S028

S029 M Code Read When CNC executes M CODE, this FLAG will be ON, and tell LADDER to execute M
CODE. The content of M CODE is saved in R1. After CNC issues this FLAG, it has to wait
until M CODE FIN's C BIT FLAG ON, then executes the next BLOCK.

CNC and PLC Interface – 41

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S030 Distribution After G code has finished moving command in single block, system will send
End DEN(distribution end) signal, usually used when G and M codes move simultaneously
and need to wait for the completion of the movement command.
Example: G01 X100. M9 // G and M codes are on the same line
When X axis really reaches 100.(G code command in this block has been finished), S30
will be ON, M9 can know that G01 command is finished by S30 and finish M code
action.
Ladder diagram writing example
Assuming that the M9 command is to turn off the cutting water, and it needs to wait
for the completion of the movement command, it is necessary to check S30 first.

Assuming that the M8 command is to turn on the work light, there is no need to wait
for the completion of the movement command, and there is no need to check S30.

After that, the combined judgment result of A109 and A108 will be updated to A38 as
the judgment of whether the M code is completed.

And wait for the M, S, T codes to be completed before turning C38 ON. If one of them
has not been completed, C38 remains OFF.

Precautions
1. If the PLC turns off C38 when it reads the M code, no matter the GM code is in the
same line or only the M code, the system will check whether the NC has been
distribution end or not, and after the NC has been distribution end, set S30 to ON.
2. If the PLC turns C38 ON, no matter the line is the same line as GM or only the M
code, the system will set S30 to OFF and start to execute the next line of
instructions.
If the M code instruction does not need to wait for the completion of the
movement instruction, there is no need to check S30.

CNC and PLC Interface – 42

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S031 Alarm • When an alarm appears in CNC or driver, and makes the system must stop or
feedhold, and this flag will be ON.
• In 10.118.40 and later version, when Pr741 is set to 1, this flag is not including the
axis group of independent operation has alarm.
Controller alarm:
CNC: COR alarm, MOT alarm, SPD alarm, OP alarm, COM alarm;
ROT: ROT alarm;
SPLC: SERIALPLCAXIS alarm;
SRI: SRI alarm;
Laser marking: LaserCtrl alarm.

S032 Reset 1. When press RESET on the panel, this FLAG will send a ONE SHOT signal.
2. When _Reset Action is triggered, this FLAG will send a ONE SHOT signal.

S033 NC Ready • After the boot is completed and the system is normal, NC READY FLAG will be ON.
• In 10.118.40 and later version, when Pr741 is set to 1, this status is nothing to do
with the axis group of independent operation.

S034 Require Part When the required workpieces number is reached, this S FLAG will be ON, and when
Count Cycle Start or Reset, this FLAG will be OFF.
Reached

S035 The Part When main program reads a part count M code (default as M99), this FLAG sends out
Count M- a ON/OFF one shot signal.
code in Main
Relative information: Parameter3804, C39
Program

S036 In Guidance When CNCis under Guidance Function mode, this BITwill be ON.
Mode

S037 Loss data When the user data (Registry.dat) is lost, this Bit will be ON.

S038 MACRO WAIT When system enters waiting mode (MACRO function WAIT() is read)

S039

S040

CNC and PLC Interface – 43

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S041 PLC Alarm When the PLC has an alarm, this flag will be ON, and when the PLC alarm disappears,
the flag will be OFF.
• 10.118.40D, 10.118.42 and version before:
The first 16 bits (R4x.0~R4x.15) of R40~R49 are PLC alarm messages, and the
last 16 bits are PLC warning message. The last 16 bits will not trigger S41.
• 10.118.40E, 10.118.43 and version after:
The first 16 bits (R4x.0~R4x.15) of R40~R49 are PLC alarm messages, and the
last 16 bits are can be either alarm or warning depended on the setting of
Pr3249.
When the last 16 bits are alarm messages, the S41 can be triggered.

S042 CNC Warning • When the controller or driver has an warning, this flag will be ON, and when all
Warnings disappear, the flag will be OFF.
• In 10.118.40 and later version, when Pr741 is set to 1, this flag is not including the
axis group of independent operation has warning.

S043 PLC Warning When PLC has an alarm, this flag ON, and when all alarms disappear, the flag OFF.
• 10.118.40D, 10.118.42 and version before:
The first 16 bits (R4x.0~R4x.15) of R40~R49 are PLC alarm messages, and the
last 16 bits are PLC warning message. The last 16 bits will trigger S43.
• 10.118.40E, 10.118.43 and version after:
The first 16 bits (R4x.0~R4x.15) of R40~R49 are PLC alarm messages, and the
last 16 bits can be either alarms or warnings depended on the setting of
Pr3249.
When the last 16 bits are warning messages, the S43 can be triggered.

S044

S045

S046

S047

S048

S049

S050

CNC and PLC Interface – 44

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S051

S052

S053 B Code Read This function is enabled by Pr3806.

When CNC executes to B CODE, this FLAG will be ON, and LADDER will be told to
execute B CODE, the content of B CODE will be placed in R5. After the CNC sends this
FLAG, it will wait until the B CODE FINISH (C38)'s C BIT FLAG ON, then start executing
the next BLOCK.
Only the first MST channel supports thePLC B CODE execution (refer to Pr721~Pr730)

S054 S Code Read When CNC executes to S CODE, this FLAG will be ON, and LADDER will be told to
execute S CODE, the content of S CODE will be placed in R2. After CNC issues this
FLAG, it will wait until the S CODE FINISH (C38)'s C BIT FLAG ON, then start executing
the next BLOCK.

S055

S056

S057

S058

CNC and PLC Interface – 45

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S059 Spindle Spindle Speed Arrival when Threading.

Threading
Speed Arrival Spindle CW/CCW Signal (C64/ Spindle Speed Arrival Condition
C65, R583.x/R584.x)

On The speed difference of spindle feedback Fbk

and spindle command Cmd is less than the
command speed Cmd multiplies a speed
arrival check range percentage (Pr1992 or
Pr1993).。

i.e. | Fdbk - Cmd | < Cmd * Pr1993 * 0.01

Off Spindle feedback less than 50 RPM.

i.e. Fdbk < 50 (RPM)

When the spindle is not equipped with an encoder (Pr1711~ = 0), the spindle speed
arrival determined with following conditions.

Spindle Type Spindle Speed Arrival Condition

Serial Bus Spindle Directly reflects the spindle speed arrival

information provided by driver.
(In serial communication, it can be known from
the V_CMP bit in the status of the driver packet,
S59 reacts to this bit, and the PLC can be used.)

Pulse Train Spindle Controller side considers spindle speed arrived

S59 On. (CNC's S59 is always On)
If you want to check the spindle speed arrival, you
can send an O bit to the TB16IN through the
driver, PLC can get this information, and check the
speed arrival in PLC.

S060 1st Set 1st set spindle superimposition completion signal.

Spindle
Superimposi
tion Finish

CNC and PLC Interface – 46

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S061 Spindle Spindle positioning completion signal

Orientation
Stop Finish

S062 1st Set 1st set spindle speed/angle synchronization is completed.

Spindle
Synchronizat
ion Finish

S063 Spindle axis When this S BIT is ON, it indicates that the spindle is in the position control mode;
mode when this S BIT is OFF, it indicates that the spindle is in the spindle speed control
mode.

CNC and PLC Interface – 47

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S064 Spindle Spindle speed arrival signal while cutting.

Cutting
Speed Arrival Spindle CW/CCW Signal: C64/ Spindle Speed Arrival Criteria
C65, R583.x/R584.x

On The speed difference of spindle feedback Fbk

and spindle command Cmd is less than the
command speed Cmd multiplies a speed
arrival check range percentage (Pr1992 or
Pr1993).。

i.e. | Fbk - Cmd | < Cmd * Pr1992 * 0.01

Off Spindle speed feedback < 50RPM

i.e. Fbk < 50 (RPM)

When the spindle is not equipped with an encoder (Pr1711~ = 0), the spindle speed
arrival determined with following conditions.

Spindle Type Spindle Speed Arrival Criteria

Serial Bus Spindle Directly reflects the spindle speed arrival

information provided by driver.
(In serial communication, it can be known from
the V_CMP bit in the status of the driver packet,
S59 reacts to this bit, and the PLC can be used.)

Pulse Train Spindle Controller side considers spindle speed arrived

S64 On. (CNC's S64 is always On)
If you want to check the spindle speed arrival, you
can send an O bit to the TB16IN through the
driver, PLC can get this information, and check the
speed arrival in PLC.

S065

S066

S067

CNC and PLC Interface – 48

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S068

S069 T Code Read When the controller executes to T CODE, this flag will be ON, and inform ladder to
execute T CODE, the content of T CODE will be stored in R3.
After the controller issues this flag, it will wait until C38 ON, then start to execute the
next block.

S070 At start point • When this flag is ON, it indicates it's not in processing status. When it's
processing, S70 will be OFF.
• S70 will be ON after receiving process finish signal, like Reset or M30.
• This flag can monitor the status of single axis group which is specified by R21.
• When R21 = 0, it corresponds to 1st axis group.
• When R21 = N, it corresponds to Nth axis group.

S071 At end point • When this flag is ON, it indicates it's not in processing status or the processing is
completed.
• S71 will be OFF when it's processing, and be ON when the processing is
completed.
• This flag can monitor the status of single axis group which is specified by R21.
• When R21 = 0, it corresponds to 1st axis group.
• When R21 = N, it corresponds to Nth axis group.

S072 2nd Set 2nd set spindle speed/angle synchronization is completed.

Spindle
Synchronizat
ion Finish

S073 3rd Set 3rd set spindle speed/angle synchronization is completed.

Spindle
Synchronizat
ion Finish

S074

S075

S076

S077

S078

CNC and PLC Interface – 49

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S079

S080 M00 Signal M00 is read flag. This flag is automatically enabled after the M code is read until the
system reset (Reset) or M Code Finish (C38 On).
Note:
1. Valid version: 10.114.56U, 10.116.0R, 10.116.10C, 10.116.13
2. Only support the first MST channel.
3. To ensure that the system properly enables this flag, it is recommended that in PLC
applications the C38 is off until the kernel enables this flag.

S081 M01 Signal M01 is read flag. When the optional stop function (C44) is activated, this flag will be
automatically enabled after the M code is read until the system reset (Reset) or M
Code Finish (C38 On).
Note: Same as S080.

S082 M02 Signal M02 is read flag. this flag will be automatically enabled after the M code is read until
the system reset (Reset) or M Code Finish (C38 On).
Note: Same as S080.

S083 M30 Signal M30 is read flag. this flag will be automatically enabled after the M code is read until
the system reset (Reset) or M Code Finish (C38 On).
Note1: Same as S080.
Note2: If below conditions both fulfilled, M30 will enable the program return function
(Valid version: 10.116.41, 10.117.41 and after). M30 will not be placed in R1 for
LADDER to read, and S083 is not supported at this time.
1. Pr732 * Multi-program MST channel, set to 1
2. C015 ON

S084

S085

S086

S087

S088 Screen Saver Screen saver mode enabled. (Only in CE system)

S089

CNC and PLC Interface – 50

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S090

S091

S092

S093

S094

S095

S096

S097 Exe File CRC When this signal is ON, it indicates that system's specific file encounters CRC check
error error. This condition usually occurs. It may be that the system is infected with the
virus and cannot be recovered. The relevant records will be stored in C:
\CRC_Chk.log.
Compatibility change:
Valid version starts from 10.114.52.

S098 OCAPI Server Whether OCAPIServer is activated. When OCAPIServer is activated, this Bit is set to
is Running True; and when OCAPIServer is deactivated, this Bit is set to False.

S099 Dipole Whether Dipole connection is in progress. When any remote program is connected to
connection the kernel, this Bit is set to 1; and when no remote program is connected, this Bit is
in use set to False.

S100 DOS USB in on: DOS USB in use; off: DOS USB not in use.
use

S101~ Mapping macro system variable (#6001~#6032)

S132

S133 Axis First set of axis exchange successfully flag.

Exchange
The axis exchange is completed inside the system, and this state changes.
Status 1

S134 Axis Second set of axis exchange successfully flag.

Exchange
The axis exchange is completed inside the system, and this state changes.
Status 2

CNC and PLC Interface – 51

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S135 Axis Third set of axis exchange successfully flag.

Exchange
The axis exchange is completed inside the system, and this state changes.
Status 3

S136 Axis Fourth set of axis exchange successfully flag.

Exchange
The axis exchange is completed inside the system, and this state changes.
Status 4

S137

S138

S139

S140 4th Axis 4th axis Homing OK, 4th axis axis HOME process finished, and this FLAG will be ON.
Home OK The software stroke limit protection will be activated after homing completed.
Therefore, in the case that this S BIT FLAG is not ON, LADDER should write not
allowed to cycle start and give homing not complete alarm.

S141 5th Axis (As above)

Home OK

S142 7th Axis (As above)

Home OK

S143 8th Axis (As above)

Home OK

S144 9th Axis (As above)

Home OK

S145 10th Axis (As above)

Home OK

S146 11th Axis (As above)

Home OK

S147 12th Axis (As above)

Home OK

CNC and PLC Interface – 52

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S148 13th Axis (As above)

Home OK

S149 14th Axis (As above)

Home OK

S150 15th Axis (As above)

Home OK

S151 16th Axis (As above)

Home OK

S152 17th Axis (As above)

Home OK

S153 18th Axis (As above)

Home OK

S154

S155 4th Axis Busy When this FLAG is ON, it indicates that the fourth axis is being executed, and a new
command cannot be accepted. When this FLAG is OFF, the fourth axis is in the Idle
state, allowing new commands to be accepted.

S156 5th Axis Busy (As above)

S157 7th Axis Busy (As above)

S158 8th Axis Busy (As above)

S159 9th Axis Busy (As above)

S160 10th Axis (As above)

Busy

S161 11th Axis (As above)

Busy

CNC and PLC Interface – 53

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S162 12th Axis (As above)

Busy

S163 13th Axis (As above)

Busy

S164 14th Axis (As above)

Busy

S165 15th Axis (As above)

Busy

S166 16th Axis (As above)

Busy

S167 17th Axis (As above)

Busy

S168 18th Axis (As above)

Busy

S169

S170

CNC and PLC Interface – 54

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S171~ Servo Alarm Alarm state for the port of motion card.
S186 State
Pulse Train Drives: This S bit will be activated when motion card does not receive
alarm signal.
Serial Bus Drives: This S bit will be activated when Servo Drive sens out a alarm
signal.
system reserved S171: Pulse Train Drive- Alarm state for the port 1; Serial Bus Drive-
The station number 1 drive.
S172: Pulse Train Drive- Alarm state for the port 2; Serial Bus Drive- The station
number 2 drive.
…
S186: Pulse Train Drive- Alarm state for the port 16; Serial Bus Drive- The station
number 16 drive.
Note：
This function does not support Servo6.

Operation Restriction：
1. The slot chassis type Servo6 axis card does not support this feature.
2. This function is only supported by pulse train type and M2 type.
3. Following from item 2, when using other communication types, please use S31
and S42.
Pulse Train type：Indicates the signal status of the servo alarm contact
This S-Bit only reflects the status of the servo alarm contact corresponding to the axis
card port. When there is signal input, this S-Bit OFF; when there is no signal input, this
S-Bit ON. According to the parameter "Pr10 servo alarm contact type", the system will
trigger the corresponding axial "MOT-9 driver alarm" when this S-Bit ON/OFF is
triggered.

Servo Alarm Contact Port Alarm Signal S-17x System Alarm

Type

Pr10 = 0 ( A contact ) No ON No

Yes OFF MOT-9

Pr10 = 1 ( B contact ) No ON MOT-9

Yes OFF No

S171：Corresponding to the 1st axis card port.

S172：Corresponding to the 2nd axis card port
…
S186：Corresponding to the 16th axis card port

CNC and PLC Interface – 55

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

M2 Serial：Indicates the driver alarm state

If an M2 serial driver is used, the corresponding S-bit On will occur when a driver
alarm occurs.
S171：Corresponding to the driver station no. which is set to be 1.
S172：Corresponding to the driver station no. which is set to be 2.
…
S186：Corresponding to the driver station no. which is set to be 16.
i.e.：In the M2 serial environment, when the driver station number which set as 3
gives alarm, S173 will be On.

S190~ (System reserved area)

S290

S291 Axis Gantry The gantry calibration complete signal of the first group of gantry set. The system has
Calibration completed the calibration, then this state will be changed.
Status 1

S292 Axis Gantry The gantry calibration complete signal of the second group of gantry set. The system
Calibration has completed the calibration, then this state will be changed.
Status 2

S293 Axis Gantry The gantry calibration complete signal of the third group of gantry set. The system
Calibration has completed the calibration, then this state will be changed.
Status 3

S294 Axis Gantry The gantry calibration complete signal of the fourth group of gantry set. The system
Calibration has completed the calibration, then this state will be changed.
Status 4

S295 (System reserved area)

～
S299

S300 ECam Reload Reload the ECam insertion point R value. When this Bit is On, it means that reload is
Status completed and the electronic cam can be activated; when this Bit is Off, Reloading.

S301 1st ECam The first group of electronic cams is busy. When this Bit is On, it means that the first
Busy group of electronic cams are working; when this Bit Off, the cam relationship motion
between the master and slave axis is canceled.

CNC and PLC Interface – 56

 机床产品/Machine Tool Products
–
PLC Interface.

No Title Description

S302 2nd ECam (As above) When this Bit On is on, it indicates that the first group of electronic cams
Busy are in use; when this Bit is off, the master and slave axis are not working according to
cam relationship.

S303 3rd ECam (As above)

Busy

S304 4th ECam (As above)

Busy

S305 5th ECam (As above)

Busy

S306 6th ECam (As above)

Busy

S307 7th ECam (As above)

Busy

S308 8th ECam (As above)

Busy

S309~
S319

S321~ For robot Robot kernel usage area (non-product customization area).
S250 kernel

S351~ Keyboard S Bit mapping to keyboard scan code, and now only S355~S374 are open.
S400 Sbit

S401~ Keyboard Mapping to the keyboard scan code 1~88.

488 Scan Code

~S511 Reserved for System reserved area.

CNC

CNC and PLC Interface – 57

 机床产品/Machine Tool Products
–
PLC Interface.

1.3 PC Keyboard C/S Mapping

1.3.1 Basic Key Area

Esc F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12
401 458 460 461 462 463 464 465 466 467 468 469 470

` 1 2 3 4 5 6 7 8 9 0 - = \ Back
441 402 403 404 405 406 407 408 409 410 411 412 413 443 414

Tab Q W E R T Y U I O P [ ] Enter
415 416 417 418 419 420 421 422 423 424 425 426 427 428

Cap A S D F G H J K L ; ‘
s
430 431 432 433 434 435 436 437 438 439 440
458

Shif Z X C V B N M , . / Shift
t
444 445 446 447 448 449 450 451 452 453 454

Ctrl Alt Space Alt Ctrl

429 456 457 456 429

1.3.2 Extension Key Area

Print Scroll Pause Num / * _
470 469 453 455 474

Insert Home Up 7 Home 8↑ 9 Up +

482 471 473 471 472 473 478

Delete End Down 4← 5 6→

483 479 481 475 476 477

↑ 1 End 2↓ 3 Down Enter

472 479 480 481 428

CNC and PLC Interface – 58

 机床产品/Machine Tool Products
–
PLC Interface.

← ↓ → 0 .
475 480 477 482 483

1.4 R Register Interface

1.4.1 Resources Distribution Table

Number Instructions Reading/ Bit Permane
Writing Stora nt
Regulations ge Preservat
(HMI、PLC、 ion
MACRO)

R0~R39 CNCSystem Interface Defined Yes No

according to
the charts
below

R40~R49 PLC Alarm Message

R50~R80 User-defined Read/Write Yes No

R81~R100 Correspond to system parameters 3401~3420 Read Only Yes Yes

R101~R102 Tool Status (save in FRAM) Read/Write Yes Yes

R103~R192 Correspond to milling machine tool data Read/Write Yes Yes

T1~T90 (saved in FRAM)
User-defined (non milling machine)

R193~R255 User-defined (save in FRAM)

R256~R511 User-defined No

R512~R639 CNCSystem Interface Defined Yes No

according to
the charts
R640~R1023 No
below

R1000 Part Count Read/Write No Yes

CNC and PLC Interface – 59

 机床产品/Machine Tool Products
–
PLC Interface.

Number Instructions Reading/ Bit Permane

Writing Stora nt
Regulations ge Preservat
(HMI、PLC、 ion
MACRO)

R1002 Required Part Count Read/Write

R1004 Total Part Count Read/Write

R1005~R1007 Controller ASCIICode Read Only

R1009~R1019 CNC system machining time/up time, please Read Only

refer to the descriptions of each R value.

R1024~R1032 Milling Machine: Occupied by the milling Read/Write No No

machine auto middle function/auto tool
presetting and measuring function.
Lathe: User-Defined

R1033~R2049 User-defined Read/Write No No

R2050~R2090 Pr3810=0:User-defined Read/Write No No

Pr3810=1: Occupied by the concurrent

multiple M codes executing function

R2091~R2099 User-defined Read/Write No No

R2100~R3100 Pr3228=0: User-defined Read/Write No No

Pr3228=1: Occupied by the tool managing Yes

function

R3101~R4095 User-defined Read/Write No No

R4096~R5999 CNC System Interface Defined No No

according to
the charts
below

R6000~R7999 User-defined (save in FRAM) Read/Write No Yes

CNC and PLC Interface – 60

 机床产品/Machine Tool Products
–
PLC Interface.

Number Instructions Reading/ Bit Permane

Writing Stora nt
Regulations ge Preservat
(HMI、PLC、 ion
MACRO)

R8000~R8500 Correspond to system parameters 5001~5500 Read Only No No

R8501~R8999 CNC System Interface Read Only No No

R9000~R9999 Robot Kernel Operating Area (Not Customized Read/Write No No

Area)

R10000~R10999 CNC system value adding applications Read/Write No Yes

memory area

R11000~R14999 CNC System Interface Read Only No No

R15000~R19909 CNCsystem value adding applications non- Read/Write No No

memory area

R20000~R65535 User-defined Read/Write No No

NOTE:
1. The permanent storage of R6000~R7999 is in Fram. If using PIO3, simulator, or controller using PIO5 and
Pr5's setting is 9 (Virtual I/O Card), system will not be able to make permanent preservation.
2. DOS system only supports R0~R7999.
3. The part of this table about the macro program is only suitable for read and write R values using G10 L1000
P_ R_; if you use the @ method to read and write R values in the macro program, please refer to the Macro变
数规格.

1.4.2 Interface Instructions

No Title & Function Description Read/
Range Write
Princi
ple

R0 Marking Records the special edition version of the controller installation package. Read
special only
edition
(ISSUE-
ID + 2
version
codes)

CNC and PLC Interface – 61

 机床产品/Machine Tool Products
–
PLC Interface.

R1 M Code When the CNC executes M CODE, it stores the contents of the M CODE here for Read
the LADDER to read. only

R2 S Code When the CNC executes S CODE, it stores the contents of the S CODE here for the Read
LADDER to read. only

R3 T Code When the CNC executes T CODE, it stores the contents of the T CODE here for the Read
LADDER to read. only

R4 Synthesis feedrate command value. Unit: LIU/min

R5 B Code The function can be enabled by Pr 3806 Read

only
When CNC executes B CODE, it stores the contents of the B CODE here for the
LADDER to read.

Only the 1stMST channel supports the execution of B CODE on PLC. (Refer to
Pr721~Pr730)

R6~R1 Reserve System Reserved Area

2 d for
CNC

R13® Mode Machining mode selection Write

Selectio only
0: Not Select
n
1: Edit
2: Auto
3: MDI
4: JOG
5:INCJOG
6: MPG
7: HOME

CNC and PLC Interface – 62

 机床产品/Machine Tool Products
–
PLC Interface.

R14 Increme Incremental JOG mode and MPG mode segments settings, this R value will not Write
nt Feed be affected by Pr3207. only
INCJOG Mode:
1: x1 LIU
2: x10 LIU
3: x100 LIU
4: x1000 LIU

MPG Mode:
1: x1 LIU
2: x10 LIU
3: x100 LIU
4: The magnified rate is set in Pr2001
Note: Please refer to Pr17 for the definition of LIU.

R15 Spindle Spindle segment setting (Maximum value is 200%) Write

Override only
1. If Pr3207=1, R15 is the percentage of spindle override, i.e. R15=5 means
spindle override is 5%.
2. If Pr3207=2, override segment defined as below:
R15=1, spindle override is 50%
R15=2, spindle override is 60%
……
R15=8, spindle override is 120%
3. The actual spindle override is R15*R851~, which the unit of R851~ is defined
as percentage, it does not affected by Pr3207~

R16 Feedrate G01,G02,G03 segment setup Write

Override only
1. If Pr3207=1, R16 is the percentage of spindle override, e.g. R16=5 means
spindle override is 5%.
2. If Pr3207=2, R16 definition as below:
R16=1, spindle override is 10%
R16=2, spindle override is 20%
……
R16=20, spindle override is 200%

CNC and PLC Interface – 63

 机床产品/Machine Tool Products
–
PLC Interface.

R17 JOG JOG segment setup Write

Override only
1. If Pr3207=1, R17 is the percentage of jog override, e.g. R17=5 means spindle
override is 5%.
2. If Pr3207=2, R17 definition as below:
R17=1, spindle override is 10%.
R17=2, spindle override is 20%,
……
R17=20, spindle override is 200%.
3. The lower limit of R17 is 0, JOG Override will be 0% if R17 is set to be a
negative value; there is no upper limit for R17, but the speed of axis is limited
by Pr461~

R18 Rapid G00 segment setup Write

Traverse only
1. If Pr3207=1, R18 is the percentage of spindle override, e.g. R18=1 means
Override
spindle override is 1%.
2. If Pr3207=2, R18 definition as below:
R18=1, spindle override is F0.
R18=2, spindle override is 25%.
R18=3, spindle override is 50%.
R18=4, spindle override is 100%.

R19 Choppin Chopping feedrate segments settings Write

g only
1. If Pr3207=1, the feeding percentage equals to the content of R19.
Feedrate
e.g. R19=5 means the feedrate override is 5%.
Override
2. If Pr3207=2, the R19 definition as below:
R19=1 represents 10%
R19=2 represents 20%
……
R19=15 represents 150%

R20 Servo Servo Axis Enabled Read

Axis only
Bit 0 reserved, not using.
Enabled
Bit1 represents the 1stAxis (X) enabled.

Bit 2 represents the 2ndAxis (Y) enabled.

……

Bit18 represents the 18thAxis enabled.

CNC and PLC Interface – 64

 机床产品/Machine Tool Products
–
PLC Interface.

R21 Active Multi-Path CNC main system executing mode: Read

Session only
0: Execute the Multi-Path program or run the general non-Multi-Path program in
ID
the 1stpath.
1: Only execute the $1 program or general non-Multi-Path program in the
1stpath.
2: Only execute the $2 program or general non-Multi-Path program in the
2ndpath.
3: Only execute the $3 program or general non-Multi-Path program in the
3rdpath.
4: Only execute the $4 program or general non-Multi-Path program in the
4thpath.

Function expansions from 10.116.34, 10.117.34.

If R21.11 is OFF, the specifications remain the same as above; if R21.11 is ON,
change the specifications as below:
Bit 0, 12-31 reserved, not using

Bit 1: execute the $1 program or general non-Multi-Path program in the 1st path.

Bit 2: execute the $2 program in the 2nd path.

Bit 3: execute the $3 program in the 3rd path.

Bit 4: execute the $4 program in the 4th path.

Bit 5-10: not using, only reserved for the possibility of future expansion to 10
axis.
Bit 11: R21 definition switch.

R21 expansion function (R21.11 on) remarks;

• R21.1~R21.4 OFF: All the paths won’t CycleStart when activated C0, suggest
the developing personnel to provide proper protection for the action in PLC.
• Pr731=3 (The 1/2/3 path is the main system path), if R21.1, 2, R21.4are ON,
only the 1stand 2ndpaths CycleStart when activated C0.
• Switching R21 during machining/pause/block stop does not effect to the
actual machining paths and HMI display, suggest the developing personnel
to provide proper protection for the action in PLC.

R22 MPG: The 2nd MPG segment selection Write

1: x1 only
2: x10
3: x100
4: Base
on
Pr2001.

CNC and PLC Interface – 65

 机床产品/Machine Tool Products
–
PLC Interface.

R23 MPG: The 3rd MPG segment selection Write

1: x1 only
2: x10
3: x100
4: Base
on
Pr2001.

R24 Spindle Spindle gear shifting settings: Write

Gear only
Selectio
n 1 represents the 1st gear

2 represents the 2nd gear

3 represents the 3rd gear

9 represents the blank gear.

R25 Actual
Feedrate

R26 Program X axis program coordinate position，the unit is the minimum input unit，LIU. Read
Coordin When control precision is micro meter, its value would be: only
ate X
0.01 mm
0.01 deg,
0.0001 inch

R27 Program (As above) Read

Coordin only
ate Y

R28 Program (As above) Read

Coordin only
ate Z

R29 Program (As above) Read

Coordin only
ate
C(6th)

CNC and PLC Interface – 66

 机床产品/Machine Tool Products
–
PLC Interface.

R30 IO Signal R30.1~R30.18 correspond to the 1stAxis~ 18thAxis driver IO signal. Read
of 1st only
Note 1: Supporting 10.116.20, 10.117.21 or above version, that is supporting the
Driver
torque arrival signal.
Set
Note 2: Torque arrival signal is only supported by;
1. YASKAWA M2/M3
2. SYNTEC M2/M3
3. EtherCAT, for brands and version info refer to EtherCAT Driver Application
Manual
Note 3: To activate the function, set the driver parameters first to enable the
torque limitation function and restart the driver.
Note 4:
R30 was preset to monitor the torque arrival signal, via Pr3266~Pr3267 Select the
drive signal to be monitored (External 1 signal or Brake signal)
Pr3266 = 1, R30.1~R30.18 corresponds to the torque arrival signal of the
1st~16thaxis, the Bit becomes 1 when the torque arrives the limit value.

Pr3266 = 2, R30.1~R30.18 corresponds to the EXT1 signal of the 1st~16thaxis, the

Bit becomes 1 when the driver receives the EXT1 input signal.

Pr3266 = 3, R30.1~R30.18 corresponds to the Brake signal of the 1st~16thaxis, the

Bit becomes 1 when the driver activates the brake.
Supporting 10.116.36Y, 10.116.51, 10.117.51 and above version.
Note 5: Only YASKAWA M2/M3 supports the External 1 signal and the Brake
signal.

R31 Machine X axis machine coordinate position，the unit is the minimum length input unit: Read
Coordin LIU, same as the length unit of system parameters. only
ate X

R32 Machine (As above) Read

Coordin only
ate Y

R33 Machine (As above) Read

Coordin only
ate Z

R34 Machine (As above) Read

Coordin only
ate
C(6th)

CNC and PLC Interface – 67

 机床产品/Machine Tool Products
–
PLC Interface.

R35 Spindle Spindle machine position. Unit: 0.001 degree. Read

Machine only
Position

R36 1st Current 1st spindle speed according to the feedback value or the command value Read
Spindle if there is no encoder. If the 1st spindle is not activated, the value is fixed to 0 only
Speed RPM. Unit: RPM.

R37 Moveme Movement direction of tool relative to current working plan, unit is 0.001 degree. Read
nt only
direction
relative
to
current
working
plane

R38 Argume Argument one，the meaning is defined by the C Bit function that uses this Write
nt one argument. Only

R39 Relay 2 Relay2 A/D converter value Read

A/D only
value

R40 PLC System default alarm area, corresponds to alarm number 1 to 16, please refer to Write
Alarm the mechanical logic control alarm list for definitions. Only
Message
Bit 0~15 #1 ~ #16 PLC Alarm Message, save to history.
#1 ~ #16
#251 ~ Bit16~31 #251 ~ #266 PLC Waring Message, no save to history.
#266

R41 PLC System default alarm area, corresponds to alarm number 17 to 32, please refer Write
Alarm to the mechanical logic control alarm list for definitions. Only
Message
Bit 0~15 #17 ~ #32 PLC Alarm Message, save to history.
#17 ~
#32 Bit16~31 #267 ~ #282 PLC Warning Message, no save to history.
#267 ~
#282

R42 PLC System default alarm area, corresponds to alarm number 33 to 48, please refer Write
Alarm to the mechanical logic control alarm list for definitions. Only
Message
Bit 0~15 #33~ #48 PLC Alarm Message, save to history.
#33 ~
#48 Bit16~31 #283 ~ #298 PLC Warning Message, no save to history.
#283 ~
#298

CNC and PLC Interface – 68

 机床产品/Machine Tool Products
–
PLC Interface.

R43 PLC System default alarm area, corresponds to alarm number 49 to 64, please refer Write
Alarm to the mechanical logic control alarm list for definitions. Only
Message
Bit 0~15 #49 ~ #64 PLC Alarm Message, save to history.
#49 ~
#64 Bit16~31 #299 ~ #314 PLC Warning Message, no save to history.
#299 ~
#314

R44 PLC User define alarm message, corresponds to alarm number 65 to 80. Write
Alarm Only
Bit 0~15 #65 ~ #80 PLC Alarm Message, save to history.
Message
#65 ~ Bit16~31 #315 ~ #330. Depending on Pr3249, this area can be PLC Alarm
#80 Message or PLC Waring Message.
#315 ~
PLC Alarm Message will be saved to alarm history but PLC Warning Message will
#330
not be saved.

R45 PLC User define alarm message, corresponds to alarm number 81 to 96. Write
Alarm Only
Bit 0~15 #81 ~ #96 PLC Alarm Message, save to history.
Message
#81 ~ Bit16~31 #331 ~ #346. Depending on Pr3249, this area can be PLC Alarm
#96 Message or PLC Waring Message.
#331 ~
PLC Alarm Message will be saved to alarm history but PLC Warning Message will
#346
not be saved.

R46 PLC User define alarm message, corresponds to alarm number 97 to 112. Write
Alarm Only
Bit 0~15 #97 ~ #112 PLC Alarm Message, save to history.
Message
#97 ~ Bit16~31 #347 ~ #362. Depending on Pr3249, this area can be PLC Alarm
#112 Message or PLC Waring Message.
#347 ~
PLC Alarm Message will be saved to alarm history but PLC Warning Message will
#362
not be saved.

R47 PLC User define alarm message, corresponds to alarm number 113 to 128. Write
Alarm Only
Bit 0~15 #113 ~ #128 PLC Alarm Message, save to history.
Message
#113 ~ Bit16~31 #363 ~ #378. Depending on Pr3249, this area can be PLC Alarm
#128 Message or PLC Waring Message.
#363 ~
PLC Alarm Message will be saved to alarm history but PLC Warning Message will
#378
not be saved.

CNC and PLC Interface – 69

 机床产品/Machine Tool Products
–
PLC Interface.

R48 PLC User define alarm message, corresponds to alarm number 129 to 144. Write
Alarm Only
Bit 0~15 #129 ~ #144 PLC Alarm Message, save to history.
Message
#129 ~ Bit16~31 #379 ~ #394. Depending on Pr3249, this area can be PLC Alarm
#144 Message or PLC Waring Message.
#379 ~
PLC Alarm Message will be saved to alarm history but PLC Warning Message will
#394
not be saved.

R49 PLC User define alarm message, corresponds to alarm number 145 to 160. Write
Alarm Only
Bit 0~15 #145 ~ #160 PLC Alarm Message, save to history.
Message
#145 ~ Bit16~31 #395 ~ #410. Depending on Pr3249, this area can be PLC Alarm
#160 Message or PLC Waring Message.
#395 ~
PLC Alarm Message will be saved to alarm history but PLC Warning Message will
#410
not be saved.

R50~R User User-defined Read/

80 define Write

R81~R MLC Apply MLC system parameter No.3401~No3420 to build a LADDER which is Read
100 System adaptable to various machines, such as tool changing and etc. Only
Paramet
er

R101 Tool Tool Magazine position status Read/

Magazin Write
e
Position

R102 Current Current Spindle Tool Number Read/

Spindle Write
Used in the HMI display of T code in single program system (Pr731=1); please
Tool
refer to R525 for multi-program system.
Number

R103~ Mill Tool Correspond to milling machine tool data T1~T90 (saved in FRAM) Read/
R192 Data Write
User-defined (non milling machine)

R193~ User User-define (saved in FRAM) Read/

R255 define Write

R256~ User User-define Read/

R511 define Write

CNC and PLC Interface – 70

 机床产品/Machine Tool Products
–
PLC Interface.

R512 Net Net PLC Function, when the corresponding bit is ON, means the station in Read
Ready network is READY. All the shared data are the latest. Only
Bit 0: Reserved.
Bit 1: Station 1 ready
Bit 2: Station 2 ready
.....
Please check Pr3236~Pr3238 for Net PLC setups.

R513 Net Net PLC Function. Read

Timeout Only
The network should have been timeout when the corresponding Bit shows ON.
It’s an exception if just started up the system, but if not receiving any updates of
the station within 100ms after the connection, then it’ll be a timeout. The
information update frequency is decided by the PLC scanning time.
Bit 0: Reserved.
Bit 1: Station 1 timeout.
Bit 2: Station 2 timeout.
....

R514 Pending Pending alarm module ID of current PLC display.

alarm
Updates the pending alarm module information to PLC every 3 seconds by HMI.
module
ID For alarm module ID, please refer to Alarm Class Table.
For alarm information about serial servo drives, please also refer to to S171~186.

R515 Pending Pending alarm ID of current PLC display.

alarm ID
Updates the pending alarm information to PLC every 3 seconds by HMI.

R516 Pending Pending alarm Axis ID of current PLC display.

alarm
Updates the pending alarm information to PLC every 3 seconds by HMI.
Axis ID

R517 Pending Pending alarm Spindle ID of current PLC display.

alarm
Updates the pending alarm information to PLC every 3 seconds by HMI.
Spindle
ID

R518 Manual Define the coordinate system referring to when giving manual commands (MPG
Coordin 、JOG、INCJOG)
ate (5
0: Machine Coordinate
Axis
RTCP) 1: Program Coordinate (G92 Coordinate)
2: Tool Coordinate (Only effective in five-axis machine.)

CNC and PLC Interface – 71

 机床产品/Machine Tool Products
–
PLC Interface.

R519 Manual Manual RTCP

RTCP

Set R519 to 1 and execute G43.4 to enable RTCP.

CNC and PLC Interface – 72

 机床产品/Machine Tool Products
–
PLC Interface.

R520~ First Axis The R value in this area is the control interface of the first axis group, which can
R529 Group be used to give commands to the first axis group and monitor the status of the
Control first axis group.
Register
s
Definition and description of each R value

Definition Description Notifications

R52 Command • The user can order • If the multi-axis group

0 Register the axis group independent function
through this R is not enabled (ie
value. Pr732 is not 2), the
• The R value is a bit main system axis
value, each bit group can only be
represents controlled through
different axis group the interface of the
commands. See the first axis group (ie
table below for R520~R529), and the
details. control interfaces of
the other main
system axis groups
will be invalid.

R52 State • The user can -

1 Register monitor the status
of the axis group
through this R
value.
• The R value is a bit
value, each bit
represents
different axis group
commands. See the
table below for
details.

CNC and PLC Interface – 73

 机床产品/Machine Tool Products
–
PLC Interface.

R52 Program No. • Used to specify the • When this axis group
2 file name of the is the main system
processing axis group:
program. • If R522 is non-
For example: R522 zero, the file
= ABCD, it means name is
that the processing determined by
program with the R522.
file name "OABCD" Triggering
is assigned to the R520.0 will
first axis group. execute the
• Valid value range: processing
[0~999,999] program
specified by
R522.
• If R522 is zero,
the file name
will be
selected by
the man-
machine, and
triggering
R520.0 will be
equivalent to
triggering C0.
• The program
specified by
R522 allows
the use of $1,
$2, which is a
multi-axis
group
program.
• When the axis group
is a non-main system
axis group:
• If R522 is non-
zero,
triggering
R520.0 will
execute the
processing
program
specified by
R522.

CNC and PLC Interface – 74

 机床产品/Machine Tool Products
–
PLC Interface.

• If R522 is zero
and R520.0 is
triggered, the
axis group will
not have any
action.
• R522 does not
support to assign
multi-path profiles
large than 60 KB.

R52 Feedrate • It is used to control • If the multi-axis group

3 Override the G01/G02/G03 independent function
feed percentage of is not enabled (that is,
the axis group. Pr732 is not 2), the
• Valid value range: R523 interface of the
[-200~200] main system axis
group will be invalid,
but will be controlled
by R16.
• The interface of the
first axis group (ie
R523) is actually
invalid, and only the
interface of the
second to fourth axis
group (ie R533, R543,
R553) is valid.

R52 Rapid Travel • G00 feed • If the multi-axis group

4 Override percentage used to independent function
control the axis is not enabled (that is,
group. Pr732 is not 2), the
• Valid value range: R524 interface of the
[-100~100] main system axis
group will be invalid,
but will be controlled
by R18.
• The interface of the
first axis group (ie
R524) is actually
invalid, and only the
interface of the
second to fourth axis
group (ie R534, R544,
R554) is valid.

CNC and PLC Interface – 75

 机床产品/Machine Tool Products
–
PLC Interface.

R52 Target Tool • For multi-program -

5 Number. system (Pr731≠1),
display the T code
of the first main
system axis group
on the man-
machine screen; for
single program
system, please
refer to R102.

R52 Remaining Display the remaining -

6 block distance of the running
distance block of the axis group,
read only and always
greater than zero, the
unit is BLU.

R52 CNC Mode The switching interface • The interface of the

7 of processing mode is first axis group (ie
the same as R13. R527) is actually
invalid, and only the
interface of the
second to fourth axis
group (ie R537, R547,
R557) is valid.

R52 (Reserved) - -
8

R52 (Reserved) - -
9

Command Register Guideline (the bit out of below description No. is reserved):

No. Command Description Attention note

R520.0 Cycle Start The axis group Please refer to the

execute specified program numbers
program. above for the
designation of
executing program.

CNC and PLC Interface – 76

 机床产品/Machine Tool Products
–
PLC Interface.

No. Command Description Attention note

R520.1 Feedhold Feedhold the axis

group movement.

R520.2 Reset/Abort • Pr741 is 0 • Please refer to

• Only reset Pr741 *The rule of
the non-primary axis
internal group for setting of
status of axis group of
axis group. independent
• Pr741 is 1 operation.
• if it is the • Pr741 can be set to
axis group 1, only if the system
of is 10.118.40 and
independe later version.
nt
operation,
then reset
for axis
and
spindle
under axis
group, and
clear
alarm.
• Otherwise,
only reset
the
internal
status of
axis group.

R520.3 MPG
Simulation

R520.4 Block Block optional skip is

Optional not compatible with all
Skip G code format, a COM
alarm will appear when
the unsupported
format detected.

CNC and PLC Interface – 77

 机床产品/Machine Tool Products
–
PLC Interface.

No. Command Description Attention note

R520.5 Emergency • Pr741 is 0 • Please refer to

Stop • Not Pr741 *The rule of
support. non-primary axis
• Pr741 is 1 group for setting of
• The bit is axis group of
supported independent
only for operation.
axis group • Pr741 can be set to
of 1, only if the system
independe is 10.118.40 and
nt later version.
operation.
• When C36
is on, the
axis group
state will
be not
ready. And
when C36
is off, the
axis group
use this bit
to further
select
ready/not
ready
state.

R520.6 M30 Turning this bit to ON, • The interface of the

Support when the machining first axis group (ie
Program program is executed R520.6) is actually
Rewind to M30, it will not be invalid, and only
reset, but it will return the interface of the
to the starting second to fourth
position of the axis group (ie
program like M99 and R530.6, R540.6,
re-execute the R550.6) is valid.
machining.

CNC and PLC Interface – 78

 机床产品/Machine Tool Products
–
PLC Interface.

No. Command Description Attention note

R520.7 Single Block Turning this bit to ON, • This bit is only valid
Pause the axis group will when Pr732 is set
enter the single-block to 2.
pause state every • The interface of the
time a block is first axis group (ie
executed when the R520.7) is actually
machining program is invalid, and only
executed. Start the interface of the
machining again second to fourth
(Cycle Start), the axis axis group (ie
group will execute the R530.7, R540.7,
next block. R550.7) is valid.
• This bit only
supports the main
system axis group.
• Please switch this
bit to ON before
processing. If the
switch is performed
during processing,
it may execute
several more
blocks to enter the
single block pause.
If the user needs to
check the
processing
program during
processing, it is
recommended to
use the handwheel
to simulate R5X0.3
or M00 pause.

CNC and PLC Interface – 79

 机床产品/Machine Tool Products
–
PLC Interface.

No. Command Description Attention note

R520.8 Optional • Turn this bit to • This bit is only valid

Stop ON, and when the when Pr732 is set
machining to 2.
program is • The interface of the
executed to M01, first axis group (ie
the axis group will R520.8) is actually
enter the pause invalid, and only
state. the interface of the
• Turn this bit to second to fourth
OFF, and when axis group (ie
the processing R530.8, R540.8,
program is R550.8) is valid.
executed to M01, • This bit only
M01 will be supports the main
ignored and system axis group.
continue to
execute on the
next block.

R520.11~ Block • R520.11 Block • Only support

R520.19 Optional Optional Skip 1, '/ 10.114.20 and later
Skip #, '/#' 1' version.
• R520.12 Block • Block optional skip
Optional Skip 2, '/ is not compatible
2' with all G code
• R520.13 Block format, a COM
Optional Skip 3, '/ alarm will appear
3' when the
• R520.14 Block unsupported
Optional Skip 4, '/ format detected.
4'
• R520.15 Block
Optional Skip 5, '/
5'
• R520.16 Block
Optional Skip 6, '/
6'
• R520.17 Block
Optional Skip 7, '/
7'
• R520.18 Block
Optional Skip 8, '/
8'
• R520.19 Block
Optional Skip 9, '/
9'

CNC and PLC Interface – 80

 机床产品/Machine Tool Products
–
PLC Interface.

State Registers guideline (the bit out of below description No. is reserved):

No. State Description Attention note

R521. Busy When the system is

0 busy, this bit will be on.

R521. Feedhold When the system is

1 feedhold, this bit will be
on.

R521. Work When a system is busy(

2 S0, R521.0 on ),
feedhold( S1, R521.1
on ) or block stop( S2
on ), this bit will be on.

CNC and PLC Interface – 81

 机床产品/Machine Tool Products
–
PLC Interface.

No. State Description Attention note

R521. NC Ready • Pr741 is 0 • Only support

3 • When there 10.118.40 and
are "C36 on" later version.
or "system • Please refer to
in alarm", Pr741 *The rule
this bit will of non-primary
be off. axis group for
• When there setting of axis
are "C36 off" group of
and "system independent
no alarm", operation.
this bit will • Pr741 can be set
be to 1, only if the
represented system is
for the all 10.118.40 and
axis under later version.
axis group
whether are
all servo on.
• Pr741 is 1
• Only for axis
group of
independen
t operation
to extend
rule, and
others axis
group
remain
original rule
the same as
Pr741 is set
to 0.

CNC and PLC Interface – 82

 机床产品/Machine Tool Products
–
PLC Interface.

No. State Description Attention note

• Whe
n
there
are
"C36
on",
"Inde
pend
ent
axis
grou
p in
alar
m" or
"
R520.
5
on",
this
bit
will
be
off.

CNC and PLC Interface – 83

 机床产品/Machine Tool Products
–
PLC Interface.

No. State Description Attention note

• Whe
n
there
are
"C36
off",
"Inde
pend
ent
axis
grou
p no
alar
m"
and
"
R520.
5
off",
this
bit
will
be
repre
sente
d for
the
all
axis
unde
r axis
grou
p
whet
her
are
all
servo
on.

R521. Servo Not Ready It represents that Only support

4 whether there is any 10.118.40 and later
servo not ready under version.
the axis group.

CNC and PLC Interface – 84

 机床产品/Machine Tool Products
–
PLC Interface.

No. State Description Attention note

R521. System Alarm • ON indicates that • Only support

5 there exist(s) 10.118.40 and
alarm(s) in the axis later version.
group. • Please refer to
• OFF indicates that Pr741 *The rule
there is NO alarm in of non-primary
the axis group. axis group and
• This bit is only Pr732 *MST
supported for main channel rules of
axis groups and multi-programs
independent for setting of
subordinate axis axis group of
groups. independent
• If Pr732 is not set to operation.
2, this bit is • Pr741 can be set
supported only in to 1, only if the
the first axis group system is
for the entire main 10.118.40 and
axis groups. later version.

R521. System Warning • ON indicates that

6 there exist(s)
warning(s) in the
axis group.
• OFF indicates that
there is NO warning
in the axis group.
• This bit is only
supported for main
axis groups and
independent
subordinate axis
groups.
• If Pr732 is not set to
2, this bit is
supported only in
the first axis group
for the entire main
axis groups.

R521. Block stop During single block • Only support

7 stop( BLOCK STOP 10.118.29W,
status ), this bit will be 10.118.40C,
on. 10.118.42 and
later version.

CNC and PLC Interface – 85

 机床产品/Machine Tool Products
–
PLC Interface.

No. State Description Attention note

R521. The number of • When this bit is ON, • This bit is only
8 required it indicates that the valid when
workpieces number of required Pr732 is set to 2.
arrives workpieces of the • This bit only
axis group has supports the
reached. main system
• When Cycle Start or axis group.
Reset is triggered,
this bit will be
turned OFF.

R530~ Second The R value in this area is the control interface of the second axis group, which
R539 Axis can be used to command and monitor the status of the second axis group.
Group The definition of each R value is the same as R520~R529, and will not be listed
Control one by one. Please refer to the description of R520~R529 for details.
Register
s
Note:
1. When the axis group independent function is not enabled (Pr732 is not 2)
and the second axis group is the main system axis group, the second axis
group will be controlled by the main system axis group uniformly, and the
control interface in this area will be invalid.
The effectiveness of the control interface is as follows:
2nd Axis Group Belongs to 2nd Axis Group Belongs
Main Axis Groups to Secondary Axis
Groups

Pr732 ≠2 Ineffective (Unified control Partially Effective

by the main system axis
group)

Pr732 =2 Effective Partially Effective

2. More Information in the 軸群獨立功能應用手冊

CNC and PLC Interface – 86

 机床产品/Machine Tool Products
–
PLC Interface.

R540~ Third The R value in this area is the control interface of the third axis group, which can
R549 Axis be used to command and monitor the status of the third axis group.
Group The definition of each R value is the same as R520~R529, and will not be listed
Control one by one. Please refer to the description of R520~R529 for details.
Register
s
Note:
1. When the axis group independent function is not enabled (Pr732 is not 2)
and the third axis group is the main system axis group, the third axis group
will be controlled by the main system axis group uniformly, and the control
interface in this area will be invalid.
The effectiveness of the control interface is as follows:
3rd Axis Group Belongs to 3rd Axis Group Belongs
Main Axis Groups to Secondary Axis
Groups

Pr732 ≠2 Ineffective (Unified control Partially Effective

by the main system axis
group)

Pr732 =2 Effective Partially Effective

2. More Information in the 軸群獨立功能應用手冊

CNC and PLC Interface – 87

 机床产品/Machine Tool Products
–
PLC Interface.

R550~ Fourth The R value in this area is the control interface of the fourth axis group, which
R559 Axis can be used to command and monitor the status of the fourth axis group.
Group The definition of each R value is the same as R520~R529, and will not be listed
Control one by one. Please refer to the description of R520~R529 for details.
Register
s
Note:
1. When the axis group independent function is not enabled (Pr732 is not 2)
and the fourth axis group is the main system axis group, the fourth axis
group will be controlled by the main system axis group uniformly, and the
control interface in this area will be invalid.
The effectiveness of the control interface is as follows:
4th Axis Group Belongs to 4th Axis Group Belongs
Main Axis Groups to Secondary Axis
Groups

Pr732 ≠2 Ineffective (Unified control Partially Effective

by the main system axis
group)

Pr732 =2 Effective Partially Effective

2. More Information in the 軸群獨立功能應用手冊

R560~ Reserve Reserved for 1st Axis Group

R564 d for
CNC

R565~ Machini R565：Part Count R/W

R569 ng Info R566：Required Part Count
of 2nd R567：Total Part Count
Axis R568：Cycle Time
Group R569：Accumulated Machining Time

R570~ Machini R570：Part Count R/W

R574 ng Info R571：Required Part Count
of 3rd R572：Total Part Count
Axis R573：Cycle Time
Group R574：Accumulated Machining Time

R575~ Machini R575：Part Count R/W

R579 ng Info R576：Required Part Count
of 4th R577：Total Part Count
Axis R578：Cycle Time
Group R579：Accumulated Machining Time

CNC and PLC Interface – 88

 机床产品/Machine Tool Products
–
PLC Interface.

R580 Spindle Spindle PLC Control Mode

PLC
Under this mode, the spindle command will be controlled by PLC and decided
Control
Mode by R941~R950 (Correspond to the 1st~10thspindle).
It represents the PLC control mode when the corresponding Bit is 1; general CNC
control mode when the corresponding Bit is 0.
Bit 0, 11-31 → Reserved
Bit 1 → 1st spindle controlled by PLC
Bit 2 → 2nd spindle controlled by PLC
....
Bit 10 → 10th spindle controlled by PLC

R581 Spindle Spindle Mode Command Write

OFF Only
The corresponding Bit (R581.x) only works when the parameter 179x sets up the
spindle motor type to servo motor.
When the corresponding bit is 1, the logic axis switches to position orientation
control mode;
when the corresponding bit is 0, the logic axis switches back to spindle control
mode, the clockwise/counterclockwise rotation control is defined by R583/R584.

Bit 0, 1, 11-31 → Reserved

Bit 2 → 2nd spindle mode command.
Bit 3 → 3rd spindle mode command.
...
Bit 10 → 10th spindle mode command.
Note:
- 1st spindle mode command is controlled by C63.
- When using M code to operate the Spindle CS axis exchange, the action is
directly done by the kernel (not with C38).

R582 Spindle Spindle current axis mode Read

axis Only
When the corresponding bit is 1, the spindle is under position orientation control
mode
mode;
when the corresponding bit is 0, the spindle is under spindle speed control
mode.
Bit 0, 11-31 → Reserved
Bit 1 → 1st spindle axis control mode
Bit 2 → 2nd spindle axis control mode
...
Bit 10 → 10th spindle axis control mode

CNC and PLC Interface – 89

 机床产品/Machine Tool Products
–
PLC Interface.

R583 Rotating Spindle clockwise rotation Write

the Only
Bit 0, 1, 11-31 → Reserved
spindle
Bit 2 → 2nd spindle clockwise rotation.
clockwis
Bit 3 → 3rd spindle clockwise rotation.
e
...
Bit 10 → 10th spindle clockwise rotation.
Note:
1. 1st spindle clockwise rotation is controlled by C64.
2. To use the spindle rotating speed arrival check function correctly (parameter
1991~), it is necessary to activate the R bit to switch the system spindle into
operating mode even it is a VFD spindle.

R584 Rotating Spindle counterclockwise rotation Write

the Only
Bit0,1, 11-31 → Reserved
spindle
Bit 2 → 2nd spindle counterclockwise rotation.
counterc
Bit 3 → 3rd spindle counterclockwise rotation.
lockwise
...
Bit 10 → 10th spindle counterclockwise rotation.
Note:
1. 1st spindle counterclockwise is controlled by C65.
2. To check spindle speed arrival, this bit must be triggered even if it is a
inverter spindle.
3. To use the spindle rotating speed arrival check function correctly (parameter
1991~), it is necessary to activate the R bit to switch the system spindle into
operating mode even it is a VFD spindle.

R585 Spindle Spindle JOG Mode Command Write

JOG Only
When the corresponding bit is 1, it forces the spindle to rotate with the spindle
Mode
JOG speed set by parameter 172x.
The function is usually used on spindle tool change and modeling of Milling
machine or auto feed of Lathe.
Bit 0, 1, 11-31 → Reserved
Bit 2 → 2nd spindle JOG mode
Bit 3 → 3rd spindle JOG mode
...
Bit 10 → 10th spindle JOG mode.
Note: 1st spindle JOG mode is controlled by C60.

CNC and PLC Interface – 90

 机床产品/Machine Tool Products
–
PLC Interface.

R586 Spindle Spindle Orientation Mode Command Write

Orientati Only
When the corresponding bit is 1, it runs the spindle orientation function.
on Stop
The function only works with an encoder installed on the spindle and the
corresponding bit remains ON.
Parameter 174x: Modify the spindle orientation speed.
Parameter 175x: Modify the spindle orientation angle, the angle is the
synchronization signal position relative to the encoder. Therefore, the
parameter must be readjusted every time after changing a motor,
encoder or belt.
Parameter 176x: Modify the spindle orientation time.
R587: Show the complete signal of the spindle orientation function.

Bit 0, 1, 11-31 → Reserved

Bit 2 → 2nd spindle orientation mode.
Bit 3 → 3rd spindle orientation mode.
...
Bit 10 → 10th spindle orientation mode.
Note: 1st spindle Orientation is controlled by C61

R587 Spindle Spindle Orientation finish flag Read

Orientati Only
Bit 0, 1, 11-31 → Reserved
on Stop
Bit 1 → 1st spindle orientation finish
Finish
Bit 2 → 2nd spindle orientation finish
Bit 3 → 3rd spindle orientation finish
...
Bit 10 → 10th spindle orientation finish
Note: S61 & R587.1 both are flags of 1st spindle.

R588 Rigid Spindle rigid tapping mode

Tapping
Bit 1 → 1st spindle is in rigid tapping mode
Mode
Bit 2 → 2nd spindle is in rigid tapping mode
Bit 3 → 3rd spindle is in rigid tapping mode
...
Bit 10 → 10th spindle is in rigid tapping mode

CNC and PLC Interface – 91

 机床产品/Machine Tool Products
–
PLC Interface.

R589 Multiple This Registry stores M/S/T information triggered by S29/S54/S69, and the
Axis information will be contained until next M/S/T command is read.
Group
[ Bit 1 ~ 4, M/S/T Command Path Information ]
MST
associat R589.1 The current M/S/T is being sent by $1 (1st path).
ed
R589.2 The current M/S/T is being sent by $2 (2nd path).
informat
ion ...
[Bit 11 ~ 20 Spindle Information]
R589.11, The current M/S/T is being sent by $x, its main spindle is the first
spindle.
R589.12, The current M/S/T is being sent by $x, its main spindle is the second
spindle.
...
R589.20, The current M/S/T is being sent by $x, its main spindle is the tenth
spindle.

R590~ PLC PLC Hint(Warning) Message Area, each bit triggers one hint. There are 32 bits in
R599 warning one register, and a total 320 messages can be used.
message R590.0 Reserved
R590.1 for 1st hint message
R590.2 for 2nd hint message
..
R590.31 for 31st hint message
R591.0 for 32nd hint message
..
R592.0 for 64th hint message
..
R593.0 for 96th hint message
..
Hint message is defined from string list 23001. That is, 23001 is the content of 1st
hint, 23002 is the content of 2nd hint, so on and so forth.

CNC and PLC Interface – 92

 机床产品/Machine Tool Products
–
PLC Interface.

R600 Machine Machine Lock Write

Lock Bit 0 Reserved Only
Bit 1 for 1st axis (X) lock
Bit 2 for 2nd axis (Y) lock
...
Bit 18 for 18th axis lock
…
• The axis won’t be moving if the command (e.g. G91G00X100) is sent under
this function being activated (R600.X ON), both the remaining distance and
the program coordinate will show normally, but the machine coordinate will
be fixed till the function being turned off, then the system will synchronize
the machine coordinate with the program coordinate.
• If this function being activated (R600.X.ON) during axial movements, the axis
won’t be moving and both the remaining distance and the program
coordinate will show normally, but the machine coordinate will be fixed
right after the function being activated till the function being turned off,
then the system will synchronize the machine coordinate with the program
coordinate.

R601 Axis MPG Under the PLC Axis program, if the corresponding flag bit is 1, the feedrate speed
simulati of the PLC axis is decided by the rotating speed of MPG. The machine moves
on faster when the MPG rotates faster; the machine moves backwards when the
MPG is rotating reversely; the machine stops when the MPG stops. It is suitable
for trial machining.
Bit 0 Reserved.
Bit 1 for 1st axis (X) MPG simulation
Bit 2 for 2nd axis (Y) MPG simulation
...
Bit 18 for 18th axis MPG simulation

R602 Spindle Spindle Y-Delta request mode, the switching speed is set by parameter
Y-Delta 1841~1850.
Request
If the corresponding bit is 0 means Y connect; 1 means Delta connect.
Mode
Bit 0 Reserved.
Bit 1 is 1st axis Y-Delta connect Mode.
Bit 2 is 2nd axis Y-Delta connect Mode.
…
Bit 10 is 10th axis Y-Delta connect Mode.

CNC and PLC Interface – 93

 机床产品/Machine Tool Products
–
PLC Interface.

R603 Inhibit Inhibit specific axis moving command.

Axis
When the Inhibit Axis command is ON, the running program turns into Feedhold
Comma
state. R841~R844 will show the feedhlold reason.
nd
(Versions after 10.116.38B, 10.116.52E, 10.116.54, 10.117.54 turn into
Feedhold state, previous versions turn into Block Stop state)
Bit 0: Reserved.
Bit 1: Inhibit 1st Axis Motion Command.
Bit 2: Inhibit 2nd Axis Motion Command.
…
Bit 18: Inhibit 18th Axis Motion Command.

R604 Teach In Teach In Command Area

comman
Bit 0 Rapid orientation endpoint teaching
d
Bit 1 Straight cutting endpoint teaching
Bit 2 Arc cutting teaching. Frist trigger is the arc middle point input, second
trigger is the arc endpoint input.
Bit 3 Point coordinate teaching.
Bit 7 Designate the arc teaching plane to be G17, and add G17 in front of G codes
when generating.
Bit 8 Designate the arc teaching plane to be G18, and add G18 in front of G codes
when generating.
Bit 9 Designate the arc teaching plane to be G19 and add G19 in front of G codes
when generating.
Bit 15 Edit Overwrite Mode. On: Overwrite the line where cursor at; Off: insert
line.
<Note> R604.x Teach In Command is only allowed to be used in F2 Program Edit
-> F6 Teaching Page

R605 Tool Tool Length Measurement Write In Command

Offset
Bit 0 Tool Length Measuring Function activated.
Write
Bit 1: Z+ contacting surface write in request.
Bit 2: Z- contacting surface write in request.
Bit 3: X+ contacting surface write in request.
Bit 4: X- contacting surface write in request.
…

CNC and PLC Interface – 94

 机床产品/Machine Tool Products
–
PLC Interface.

R606 MPG MPG Shift Enable Commad Write

Shift Only
1. R606=0 Disable MPG Shift
R606=1 Enable MPG Shift
2. Caution: When MPPG shift enabled, with C16~ to assign MPG axis, the axis
can be moved by MPG under 「AUTO」and「MDI」mode. Please be extra
careful!

R607 Spindle Spindle Speed Arrival Signal, identical to S64/S59. Read

Speed Only
Bits 0, 1, 11, 21-31 Reserved.
Arrival
1. Under cutting G01/G02/G03
R607.2 means 2nd Spinde speed arrival
R607.3 means 3rd Spinde speed arrival
...
R607.10 means 10th Spinde speed arrival
2. Under threading
R607.12 means 2nd Spinde speed arrival
R607.13 means 3rd Spinde speed arrival
...
R607.20 means 10th Spinde speed arrival

R608 Modbus R608.0 Trigger this Bit to show that the master is ready for Modbus
PLC communication. ( R608.10, R608.31, and error code R5039 will be cleared when
Commu the PLC Modbus component is triggered . )
nication
R608.1 (Read Only) Transmitting Status.
R608.2 (Read Only) Waiting to Receive.
R608.3 (Read Only) Receiving.
R608.10 (Read Only) Reception finished correctly.
R608.31 (Read Only) Error Flag . ON indicates that error(s) occurred and the
error code will be displayed at R5039.
Note: All MODBUS read, write, and custom components
share R608. It is recommended to stagger the use timing
of different components to know which component the
corresponding status is for.
For example, wait for the previous component to
complete the transmission (R608.10 or R608.31 on)
before executing the next component.

CNC and PLC Interface – 95

 机床产品/Machine Tool Products
–
PLC Interface.

R609 Axis Axis Coupling Status

Coupling
When coupling type (Pr3825/Pr3865/Pr3875/Pr3885) ≠1 (non-mechanical
Status
coupling type), the Register displays coupling status. If the coupling status is
changed by C46/R614, this Register will update after system finishes mode
switch.
Bit 1: 1st set of axis is coupling.
Bit 2: 2nd set of axis is coupling.
Bit 3: 3rd set of axis is coupling.
Bit 4: 4th set of axis is coupling.
Note : C046/R614 and the Gantry Tuning Function can affect the coupling state
R609.

R610 Skip PLC Axes that executing G31 or G28.1 skip command touch the skip signal and Read
Position record the position. Only
of PLC
Bit 0: Reserved
axis
Bit 1: 1st axis (X) skip occur
Latched
Bit 2: 2nd axis (Y) skip occur
...
Bit 18: 18th axis skip occur

R611 Axis Display each axis movement status, according to the feedback value, failing the
Moveme Zero Speed Check means the axis is moving. Zero Speed Check parameters are
nt Flag Pr901-920.
Bit 0 Reserved
Bit 1 : 1st axis (X) is moving
Bit 2 : 2nd axis (Y) is moving
...
Bit 18 : 18th axis is moving

R612 Machine Machine Positive Direction Lock.

Positive
Bit 0 Reserved
Directio
Bit 1 : 1st axis (X) positive direction lock.
n Lock
Bit 2 : 2nd axis (Y) positive direction lock.
...
Bit 18 : 18th axis positive direction lock.
• The axis won’t be moving if the command (e.g. G91G00X100) is sent under
the function being activated (R612.xx ON), and both the program and the
machine coordinate will be fixed.
• If the function being activated (R612.x ON) during axial movements, the axis
will stop moving immediately, and both the program and the machine
coordinate will be fixed right after the function being activated.

CNC and PLC Interface – 96

 机床产品/Machine Tool Products
–
PLC Interface.

R613 Machine Machine Negative Direction Lock.

Negiaive
Bit 0 Reserved
Directio
Bit 1 : 1st axis (X) negative direction lock.
n Lock
Bit 2 : 2nd axis (Y) negative direction lock.
...
Bit 18 : 18th axis negative direction lock.
• The axis won’t be moving if the command (e.g. G91G00X100) is sent under
the function being activated (R612.xx ON), and both the program and the
machine coordinate will be fixed.
• If the function being activated (R612.x ON) during axial movements, the axis
will stop moving immediately, and both the program and the machine
coordinate will be fixed right after the function being activated.

R614 Axis Axis coupling status switch.

Coupling
If Coupling Type (Pr3865/Pr3875/Pr3885) ≠1 (non-mechanical coupling), the
Request
actual coupling mode is decided by this Register. When FLAG ON, the coupling
axis direction turns into coupling status; when FLAG OFF, the coupling axis
direction leaves coupling status. Under coupling status, the slave axis moves
with the set ratio when the spindle moves.
Bit 0, 1 Reserved
Bit 2 → 2nd set of axis coupling command
Bit 3 → 3rd set of axis coupling command
Bit 4 → 4th set of axis coupling command
Note:

• The 1st set of axis coupling command is activated by C46.

• Please refer to R609 Axis Coupling Status for axis coupling status.

CNC and PLC Interface – 97

 机床产品/Machine Tool Products
–
PLC Interface.

R615~ Second Second M/S/T Execution Channel

R618 M/S/T
Executio R615 command and status
n R616 M code
Channel R617 S code
R618 T code

R615.0 MST code finish (PLC→CNC)

R615.1 DEN moving command finish (CNC→PLC)
R615.2 M code read (CNC→PLC)
R615.3 S code read (CNC→PLC)
R615.4 T code read (CNC→PLC)
…
R615.8 M/S/T code is executed by 1st path ($1)
R615.9 M/S/T code is executed by 2nd path ($2)
R615.10 M/S/T code is executed by 3rd path ($3)
R615.11 M/S/T code is executed by 4th path ($4)
R615.12 M00 Read Flag
R615.13 M01 Read Flag; need to activate the optional stop function (C44).
R615.14 M02 Read Flag
R615.15 M30 Read Flag
Note:
1. Valid version: 116.41, 10.117.41
2. The flag only works when the parameter of “Pr732 * multi-program MST
channel rules” is set to 1.
3. The flag will activate automatically after reading the M code till system reset
(Reset) or M Code Finish (R615.0 On).
4. To ensure the system activates the flag correctly, R615.0 should be OFF
before the flag being activated by the kernel in PLC applications.
R615.16 The current M/S/T is being sent by $x, its main spindle is the 1st spindle.
R615.17 The current M/S/T is being sent by $x, its main spindle is the 2nd
spindle.
…
R615.23 The current M/S/T is being sent by $x, its main spindle is the 8th spindle.
R615.29…The current M/S/T is being sent by $x, its main spindle is the 9th
spindle.
R615.30…The current M/S/T is being sent by $x, its main spindle is the 10th
spindle.
(When parameter 3810 activates the Single Block multi-M code execution
function)
R615.24 1st M code execution request
R615.25 2nd M code execution request
R615.26 3rd M code execution request
R615.27 4th M code execution request

CNC and PLC Interface – 98

 机床产品/Machine Tool Products
–
PLC Interface.

R615.28 5th M code execution request

R619~ Third M/ Third M/S/T Execution Channel

R622 S/T
R619 Control and Status Register
Executio
n R620 M Code
Channel
R621 S Code
R622 T Code
For related functions, please refer to the description of R615~R618.

R623~ Fourth Fourth M/S/T Execution Channel

R626 M/S/T
R623 Control and Status Register
Executio
n R624 M Code
Channel
R625 S Code
R626 T Code
For related functions, please refer to the description of R615~R618.

R627 Axis The axis switch to torque control under the mode, the corresponding commands Write
Torque are R880~R895. Only
Mode
When the corresponding bit is 1 means the axis is switched to torque control
mode; when the corresponding bit is 0 means the axis is position control mode.
R627.0 Reserved, not using.

R627.1 represents the 1staxis torque control mode

R627.2 represents the 2ndaxis torque control mode

...

R627.18 represents the 18thaxis torque control mode

Note 1: The interface only works for serial bus communication.

Note 2: The control interface only supports version 10.118.10 and below.

CNC and PLC Interface – 99

 机床产品/Machine Tool Products
–
PLC Interface.

R628 Spindle Display the current spindle cutting speed mode. Read
CSS Only
When the corresponding Bit is ON, the spindle is in the constant surface cutting
Mode
speed control mode (G96); when the corresponding Bit is OFF, the spindle is in
the rotating speed control mode (G97).
Bit 0, 5-31 Reserved

Bit 1 → machining spindle of the 1st path

Bit 2 → machining spindle of the 2nd path

Bit 3→ machining spindle of the 3rd path

Bit 4 → machining spindle of the 4th path

R629 Axis M The register provides the PLC axis M code request signal. When axis executes to Read
code M codes, the corresponding Bit ON and request new M code from PLC program, Only
M code contents are stored in the R618~R696. After the controller send the
request, only until M code completion signal (R630) On, then next block start
executing.
Bit 0 Reserved

Bit 1 → 1st axis (X) M code request

Bit 2 → 2nd axis (Y) M code request

...

Bit 18 → 18th axis M code request

R630 M Code Completion Signal (Please refer to R629) Write

Only
Bit 0 Reserved, not using

Bit 1 represents the 1staxis (X) M code completion.

Bit 2 represents the 2ndaxis (Y) M code completion.

...

Bit 18 represents the 18thaxis M codes completion.

R631 The Each spindle Y-Delta target state

target When the corresponding bit is 0, the spindle is Y connection; 1 means Delta
winding connection.
of Y- Bit 0 reserved
Delta of Bit 1: 1st spindle Y-Delta target state.
each Bit 2: 2nd spindle Y-Delta target state.
spindle. ...
Bit 10: 10th spindle Y-Delta target state.

CNC and PLC Interface – 100

 机床产品/Machine Tool Products
–
PLC Interface.

R632 The Each spindle Y-Delta adopted winring

adopted When the corresponding bit is 0, the spindle is Y connection; 1 means Delta
winring connection.
of Y- Bit 0 reserved
Delta of Bit 1: 1st spindle Y-Delta target state.
each Bit 2: 2nd spindle Y-Delta target state.
spindle. ...
Bit 10: 10th spindle Y-Delta target state.

R633~ 1st~4th The arrival flag for 1st~4th reference point (machine coordinate), will be Read
R636 referenc updated at each PLC scan time. Only
e point
(machin • R633: Represent arrival status of each axis for 1st reference point (machine
e origin).
coordina • R634: Represent arrival status of each axis for 2nd reference point
te) (corresponding to Pr2801~).
arrival • R635: Represent arrival status of each axis for 3rd reference point
flag (corresponding to Pr2821~).
• R636: Represent arrival status of each axis for 4th reference point
(corresponding to Pr2841~).
Bit 0 reserved, not used.

Bit 1 represents reference point arrival flag for 1st axis (X). If the axis has arrived
then flag is 1 (On), otherwise 0 (Off).

Bit 2 represents reference point arrival flag for 2nd axis (Y). If the axis has arrived
then flag is 1 (On), otherwise 0 (Off).
...

Bit 18 represents reference point arrival flag for 18th axis. If the axis has arrived
then flag is 1 (On), otherwise 0 (Off).
• To determine whether the arrival flag is on or not, the following conditions
must be confirmed simultaneously.
a. The homing process has finished (S Bit of Axis Home OK should be
on) and the axis is not used as spindle.
b. The axis has arrived at target machine position.
c. The position error between servo command and motor feedback
should be less or equals to Pr481~Pr500 Axial rapid travel in-position
window.

R637~ Reserve System Reserved Area

R639 d for
CNC

CNC and PLC Interface – 101

 机床产品/Machine Tool Products
–
PLC Interface.

R641~ Axis MPG Set the manual ratio of each axis; set the manual multiplier ratio of the MPG JOG Write
R658 comman axis. Only
d
multiplie R641: multiplier ratio of the 1st axis.
r ratio R642: multiplier ratio of the 2nd axis.
so on and so forth...
The actual affective ratio is equal to the MPG segment (defined by R14, R22, R23)
multiplied the multiplier ratio of the register.
Register=1000 means the ratio is 1.0
Register=1 means the ratio is 0.001, but when Register=0 ratio is default as 1.0.
Note: The R value only valid when the MPG corresponding coordinate is set up to
be controlled by MLC (Ref. Parameter 2031~2040).

R661~ PLC axis Set the feedrate range of each axis PLC program -200~200, Default value 100. Write
R678 program Only
G00/G01 R661 → feedrate range of the 1st axis PLC program
feedrate R662 → feedrate range of the 2nd axis PLC program
override
so on and so forth...

R681~ PLC axis (please refer to R629) Read

R698 M code Only
value

R700 Actual Actual compound feedrate command of the first main system axis group, unit:
compou LIU/min (PLC axis doesn’t count in compound feedrate calculation)
nd
Always regarded as linear axis, for the rotary axis is in Imperial units, the value
feedrate
should be magnified 10 times.

i.e. Pr17=2, under Imperial units, the 3rd axis is rotary axis feedrate F100.
R700 = 100 (IU/min) * (10000 LIU/IU)
LIU: 0.0001 inch, IU = inch
R703 = 100 (IU/min) * (1000 BLU/IU)
BLU: 0.001 deg, IU = deg
Thus, R700 is 10 times to R703.

R701~ Axis Velocity of each axis, Servo On mode: according to command value; Servo Off Read
R718 Velocity mode: according to feedback value, unit : BLU/min. Only

R701 → single axis speed of the 1st axis

R702 → single axis speed of the 2nd axis

so on and so forth...

CNC and PLC Interface – 102

 机床产品/Machine Tool Products
–
PLC Interface.

R721~ Program Axis program coordinate position，unit: minimum input unit (LIU). Read
R738 Coordin Only
ate R721 → 1st axis program coordinate position

R722 → 2nd axis program coordinate position

so on and so forth...

When control precision is micro meter and the value:

0.01 mm
0.01 deg,
0.0001 inch

R741~ Machine Axis machine coordinate position, unit: minimum input unit (LIU). Read
R758 Coordin Only
ate R741 → 1st axis machine coordinate position

R742 → 2nd axis machine coordinate position

so on and so forth...

R761~ Spindle Display the machine position of the corresponding spindle, unit: 0.001 deg. Read
R770 Machine Only
Position R761 → 1st spindle machine position
R762 → 2nd spindle machine position
so on and so forth...

R771~ Spindle Current Spindle Speed according to the feedback value, if there’s no encoder Read
R780 Speed then refer to the command value. If the spindle is not activated, the value should Only
be fixed to 0. Unit: RPM.

R771 → 1st spindle speed.

R772 → 2nd spindle speed.
so on and so forth...

CNC and PLC Interface – 103

 机床产品/Machine Tool Products
–
PLC Interface.

R781 Axis This register is used to determine which axis group information will be R/W
group processed by the HMI.
switchin
R781=1: The HMI will display the processing information of the 1st axis group,
g
and the settings made by the HMI will be set to the 1st axis group.
interface
R781=2: The HMI will display the processing information of the 2nd axis group,
of HMI
and the settings made by the HMI will be set to the 2nd axis group.
R781=3: The HMI will display the processing information of the 3rd axis group,
and the settings made by the HMI will be set to the 3rd axis group.
R781=4: The HMI will display the processing information of the 4th axis group,
and the settings made by the HMI will be set to the 4th axis group.
If R781 is set to other values, the HMI will always process the processing
information of the 1st axis group.
Example: R781 is set to 2. then:
1. The HMI will display the information of the 2nd axis group.
2. Set the number of workpieces to be processed through the HMI, and it will be
set to the 2nd axis group.

R782~ Spindle Spindle Gear setting ： Write

R790 Gear 1 → 1st Gear Only
Selectio 2 → 2nd Gear
n
3 → 3rd Gear
9 → Neutral
R782 → 2nd spindle gear position
R783 → 3rd spindle gear position
so on and so forth...
Note: 1st spindle gear position is controlled by R24 setting.

CNC and PLC Interface – 104

 机床产品/Machine Tool Products
–
PLC Interface.

R791~ Effective The machining spindle under multi-axis applications is selected by the content Write
R794 Spindle of the register, value definition: Only
Selectio
n 1. the 1st spindle is the machining spindle
2. the 2nd spindle is the machining spindle
3. the 3rd spindle is the machining spindle
4. the 4th spindle is the machining spindle
so on and so forth...
R791 → machining spindle of 1st path
R792 → machining spindle of 2nd path
R793 → machining spindle of 3rd path
R794 → machining spindle of 4th path
When the spindle of the path is selected, the S command given to the path ($1,
$2) will be directly send to the corresponding affective spindle. e.g. R791 = 1,
R792 = 2,

$1 S1000 → 1000 RPM is assigned to 1st spindle

$2 S1500 → 1500 RPM is assigned to 2nd spindle
Note: Before switching the machining spindle (R791~), if the current spindle is in
the tapping state, must first cancel with G80 to avoid unexpected subsequent
machining actions.

R801~ MLC System parameter No.3421 ~ No.3450 of MLC parameter (Extension Parameter), Read
R830 System for which one LADDER can be applicable to various machines, i.e. tool change… Only
Paramet
er

R831~ MLC System parameter No.3451 ~ No.3460 of MLC parameter (Extension Parameter),
R840 System for which one LADDER can be applicable to various machines, i.e. tool change…
Paramet
** These parameters don't need to Login and can be edit by user.
er

R841~ Cause of Cause of block stop.

R844 Block
0: Normal. Stop by M00/M01 or Feedhold by user.
Stop
1: axis motion prohibited command, system automatically enter
Feedhold status.

R841 Cause of 1st path block stop.

R842 Cause of 2nd path block stop.
R843 Cause of 3rd path block stop.
R844 Cause of 4th path block stop.

~R850 Reserve System reserved area

d for
CNC

CNC and PLC Interface – 105

 机床产品/Machine Tool Products
–
PLC Interface.

R851~ Spindle Override % of an individual spindle. R15 is the common override of all spindles,
R860 Override the actual override is R15*R851~. The unit of R851~ is %, and does not affected
by Pr3207 setting.

R851 1st Spindle override

R852 2nd Spindle override
....
R856 10 th Spindle override

R861~ Break Machine coordinate position where machining stops. Unit is BLU, and the
R870 point Registries support up to 10 axes.
machine
Machining Break Point Machine Position, unit: minimum length unit (BLU), same
position
as the length parameter of system parameters. Registries support up to 10 axis.

R871~ Spindle Spindle effective speed command, unit: RPM. Read

R879 Effective Effective RPM means the actual speed command after calculation with spindle Only
Speed override or constant surface speed.
Comma
The Effective Command is the final effective speed command value calculated
nd
after the spindle override command, constant surface speed cutting (G96/G97)
and all other related factors.

R871 1st Spindle Effective Speed Command

R871 2nd Spindle Effective Speed Command
...

R879 9th Spindle Effective Speed Command

Note: Please refer to R930 for the 10thspindle.

CNC and PLC Interface – 106

 机床产品/Machine Tool Products
–
PLC Interface.

R880~ Referenc Write/

Control Mode Machine Model Descriptions
R895 e Value Read
for D/A
of Servo Servo card D/A EZ, 10A R881 is active as D/A
Card or command (range: ± command only if all the axis
Torque 10000mV), effective and spindle have not been
Comma version: 10.116.5 defined as voltage control
nd mode (i.e., Pr381~ ≠ 1,
Pr1791~ ≠ 0/2).

10B/11B R881 is active as D/A

command only if all the axis
and spindle which are linked
to P5~P8 have not been
defined as voltage control
mode (i.e., Pr381~ ≠ 1,
Pr1791~ ≠ 0/2)

Super-servo4 R880~R883 are active as

servo card D/A command
only if all the axis and
spindle of the servo card
have not been defined as
voltage control mode (i.e.,
Pr381~ ≠ 1, Pr1791~ ≠ 0/2)
R880 → 1st servo card D/
A command.
R881 → 2nd servo card D/
A command.
R882 → 3rd servo card D/
A command
R883 → 4th servo card D/
A command

Super-servo6 R880 → 1st servo card D/

A command
R881 → 2nd servo card D/
A command
R882 → 3rd servo card D/
A command
R883 → 4th servo card D/
A command

CNC and PLC Interface – 107

 机床产品/Machine Tool Products
–
PLC Interface.

Control Mode Machine Model Descriptions

60A Pre-defined zone for DAC

value, reserve 16 channels.
ps: Except Servo-6/60A, all
other models needs to
activate at least 1 axis to use
this function.

Servo Card 1st D/A & 3, 6, 11, 21, eHMC Have 2 sets of DA (DA1 &
2nd D/A command series DA2).
(Range ± 10000mV), (effective version: 1. When DA is not occupied
10.114.56R, by any spindle or axis,
10.116.0O, Registries can control DA
10.116.6G, voltage.
10.116.10A) 2. Under condition 1, it’s
able to control DA1
output with R880; DA2
FC-
output with R884.
B, FC-60WA,
FC-60CB and 60DB
(Valid
version: 10.118.12R,
10.118.22)

71SA Have 2 sets of D/A (DA1 &

DA2)
(Valid
version: 10.118.12R, 1. When the DA is not
occupied by any spindle
10.118.22)
or axis, Registries can
control DA voltage.
2. Under condition 1, it’s
able to control DA1
output with R880; DA2
output with R884.
3. The DA output of FC-
LSMK laser source is
controlled by R881.

70SB The DA output of the laser

source is controlled by R881.
(Valid version:
10.118.12R,
10.118.22)

CNC and PLC Interface – 108

 机床产品/Machine Tool Products
–
PLC Interface.

Control Mode Machine Model Descriptions

Expansion D/A Card Multi-Axis Servo When Pr3261~Pr3263 =n004

on Multi-Axis Servo Drive Embedded (n: card station number),
Drive Embedded Controller R880/R884/R888/R892
Controller represents the 1st~4th DA
(Valid version:
port on expansion card.
(Range:±10000, unit: 10.116.36I,
mV) 10.116.41, 10.117.41
)

Rated Torque 6MD, 20, 21, 200 Serial controllers support

Reference Command series torque control. Use R627 to
(Unit: Rated torque/ enable/disable torque
(Valid version: 10.11
1000) control mode. When axis
4.56, 10.116.0)
under R627 torque control
mode, these registers are
torque reference command,
with positive value means
positive output, negative
value means negative
output.
R880 → 1st axis torque
command.
R881 → 2nd axis torque
command.
...
R895 → 16th axis torque
command
Note1: Not Support the
17th & 18thaxis.
Note2: The control interface
only supports version
10.118.10 and below.

CNC and PLC Interface – 109

 机床产品/Machine Tool Products
–
PLC Interface.

Control Mode Machine Model Descriptions

D/A port output 720BA D/A:

PWM port output R880 1st port D/A output，
parameter range: ±10000，unit: mV
R884 2nd port D/A output，
range: ±10000，unit: mV
R888 3rd port D/A output，
range: ±10000，unit: mV
R892 4th port D/A output，
range: ±10000，unit: mV
PWM:
R881 1st port PWM output
basic unit(B)，range:
0~65535，unit: ns
R882 1st port PWM output
period(T)，range:
0~65535，unit: times for
basic unit
R883 1st port PWM output
duty cycle(t)，range:
0~65535，unit: times
for basic unit

R896~ A/D (1) A/D converter value, 2 channel per servo 6 board. Read
R899 value (2 ) Pre-defined zone for ADC value, reserve 4 channels. Only

Control Mode Machine Model Descriptions

A/D port input 720BA R896 1st port A/D input，

unit: mV
72BA
R897 2nd port A/D input，
unit: mV

CNC and PLC Interface – 110

 机床产品/Machine Tool Products
–
PLC Interface.

R900 Data A/D converter value, 2 channel per servo 6 board (DOS only) Write
Acquisiti Only
DOS system:
on
Trigger When this R value is On, the oscilloscope will activate the capture
(On DOS function.
System)
WinCE system:
Ballbar
When this R value is On, start executing ballbar tuning.
Adjust
Trigger When this R value is Off, stop executing ballbar tuning.
(On
WinCE)

R901~ Axis Temperature Compensation Amount, unit: BLU Write

R918 tempera Only
ture R901 1st axis temperature compensation amount
compen R902 2ndaxis temperature compensation amount
sation
amount …

R918 18thaxis temperature compensation amount

R919 Laser D/ Laser D/A output. Range: ±10000. Unit: mV.

A output
Hint: Only supported on 720 SA.

R920 EDM EDM discharge enabled. (0: Disable, 1: Enable) Write

discharg Only
e enable.

R921 EDM EDM discharge control mode. Write

control 0: Fixed Frequency. suitable for laser machine. Only
mode 1: Fixed Energy. suitable for EDM.

R922 EDM EDM normal ON time level, unit: Discharge resolution set by Pr3831. Write
normal Only
(When PR3261~Pr3263= n004, this parameter means the setting for PWM on
ON time
Expandable Card of Servo Drive Embedded Controller. Valid version 10.116.36I,
10.116.41, 10.117.41)

R923 EDM EDM normal OFF time level, unit: Discharge resolution set by Pr3831. Write
normal Only
(When PR3261~Pr3263= n004, this parameter means the setting for PWM on
OFF time
Expandable Card of Servo Drive Embedded Controller. Valid version 10.116.36I,
10.116.41, 10.117.41)

R924 EDM arc EDM arc ON time level, unit: Discharge resolution set by Pr3831. Write
ON time Only

CNC and PLC Interface – 111

 机床产品/Machine Tool Products
–
PLC Interface.

R925 EDM arc EDM arc OFF time level, unit: Discharge resolution set by Pr3831. Write
OFF time Only

R926 Reserve Reserved for system.

d

R927 Total Constant energy machining, total discharge count. Read

Discharg Only
e Count

R928 Normal Constant energy machining, total normal discharge count. Read
Discharg Only
e Count

R929 Abnorm Constant energy machining, total abnormal discharge count. Read
al Only
Discharg
e Count

R930 Spindle The effective speed command of the 10thspindle, unit: RPM.
Effective
Speed The Effective Command is the final effective speed command value of spindle
Comma commend calculation result from percentage, constant linear velocity control on
nd surface (G96/G97), and all related factors.

R934 MPG: 4th MPG override selection. Write

only
1: x1
2: x10
3: x100
4: x
magnifie
d based
on
Pr2001
setting.

R935 MPG: 5th MPG override selection. Write

only
1: x1
2: x10
3: x100
4: x
magnifie
d based
on
Pr2001
setting.

CNC and PLC Interface – 112

 机床产品/Machine Tool Products
–
PLC Interface.

R936 MPG: 6th MPG override selection. Write

only
1: x1
2: x10
3: x100
4: x
magnifie
d based
on
Pr2001
setting.

R937 MPG: 7th MPG override selection. Write

only
1: x1
2: x10
3: x100
4: x
magnifie
d based
on
Pr2001
setting.

R938 Start Start program No. of "auxiliary program function before and after machining" Read/
program Write
1. When value = or <0, auxiliary program will not be executed.
No. of
2. Auxiliary program needs to start with letter "O". (O####)
"auxiliar
3. If value is less than 4 digit, system recognizes it as a 4 digit program No.; if
y
less than 6 digit, system recognizes a 6 digits.
program
Example:
function
• R938 = 12 → Program No. O0012
before
• R938 = 1234 → Program No. O1234
and after
• R938 = 12345 → Program No. O012345
machini
• R938 = 123456 → Program No. O123456
ng"

R939 End End program No. of "auxiliary program function before and after machining" Read/
program Write
1. When value = or <0, auxiliary program will not be executed.
No. of
2. Auxiliary program needs to start with letter "O". (O####)
"auxiliar
3. If value is less than 4 digit, system recognizes it as a 4 digit program No.; if
y
less than 6 digit, system recognizes a 6 digits.
program
i.e.:
function
• R939 = 12 → Program No. O0012
before
• R939 = 1234 → Program No. O1234
and after
• R939 = 12345 → Program No. O012345
machini
• R939 = 123456 → Program No. O123456
ng"

CNC and PLC Interface – 113

 机床产品/Machine Tool Products
–
PLC Interface.

R940 Excessiv In absolute system, when CNC axis position displacement exceeds the range set Read
e in Pr1021~1040 during power off, the Bit of corresponding R value will be On. Only
Displace When C84 ON this R value is cleared to 0.
ment
If needs the Bit value to send MLC alarms of corresponding axis, it can be
During
processed by filling the value into R44~R49.
Power
Off Bit 0: 1st axis excess displacement during power off
Bit 1: 2nd axis excess displacement during power off
...
Bit 18: 18th axis excess displacement during power off
Note:
Due to the limitation of ladder file format, the R value that can be accessed on
the ladder edit is only till R639. Therefore, when using this R value, better choose
a user-defined section and an accessible R value then write the ladder as the
example shows below (take R50 for example).

R941~ PLC PLC Spindle Command, unit: RPM. This function enabled by R580. Read/
R950 Spindle R941 → 1st spindle Write
Comma R942 → 2nd spindle
nd ...
R950 → 10th spindle

R951~ Current Current interpolation mode, possible value: 1/2/3/4/33/34/35 Read

R954 interpol Only
ation R951 current interpolation mode of 1st path.
mode R952 current interpolation mode of 2nd path.
R953 current interpolation mode of 3rd path.
R954 current interpolation mode of 4th path.

CNC and PLC Interface – 114

 机床产品/Machine Tool Products
–
PLC Interface.

R956~ Extende Switch & Operation Status of extended stroke limit Read/
R959 d Stroke Write
The extended limit switch is defined by the Bit value, Bit =1 means activated; =0
Limit
means de-activated.

R956 .0~.31 : 01~32 set of extended stroke limit switch.

R957 .0~.31 : 01~32 set of extended stroke limit operation status.
R958 .0~.31: 33~64 set of extended stroke limit switch.
R959 .0~.31: 33~64 set of extended stroke limit operation status.
Notification:
1. Due to the limitation of ladder file format, the R value that can be accessed
on the ladder edit is only till R639. Therefore, when using this R value, better
choose a user-defined section and an accessible R value then write the
ladder as the example shows below (take R50 for example).

2. The supported models are listed below.

81RG / HC-8A / HC-10A/ HC-7C / HC-8C / HC-10C / HC-15C / HC-8E / HC-10E /
HC-15E / HC-8S / FC-A / FC-B / FC-C

R961~ Home The shift (offset) from Home Dog signal to motor index. Unit for rotary encoder:
R978 Dog 0.01 rev; for linear encoder: 0.01 mm. (Equivalent to System Data 56~59)
Shift
R961 is the home dog shift limit of the 1st axis

R962 is the home dog shift limit of 2nd axis

so on and so forth……

R981~ Axis The absolute position feedback of each axis, which is the axial motor encoder Read
R998 Absolute feedback. For axis with dual feedback control, the Registry displays feedback Only
Counter from 2nd (external) encoder. Unit: BLU.

R981, the position sensor value of the 1st axis

R982, the position sensor value of the 2nd axis

so on and so forth……

R1000 Part Part count Read/

count Write

R1002 Require Required part count Read/

d part Write
count

CNC and PLC Interface – 115

 机床产品/Machine Tool Products
–
PLC Interface.

R1004 Total Total part count Read/

part Write
count

R1005 Controll 4 bytes as one set, uses “little endian” display method; below is an example with Read
~R100 er S/N M9A0001: only
7 ASCII
Code Number Hexadecimal Decimal (Controller Display)

R1005 0x30 0x41 0x39 0x4D 809580877

0 A 9 M

R1006 0x31 0x30 0x30 3223600

1 0 0

R1007 0 0

R1007 is reserved for “controller serial number” expansion.

Situation Applied:
If customers have encryption demands for “machine MACRO”, usually check the
controller serial numbers with CHKSN ("Serial Number") inside the MACRO. But
if customer wants to protect the serial number again with the encryption logic
designed by themselves, then will decrypt inside the MACRO to compare the
controller serial "number", and R1005~R1007 can provide customers to perform
this checkup.
Note: For “little endian” method, the least significant bit is in front of the most
significant bit.

R1009 Motion Motion interpolation times after power-on, refer to System Data No. 4, multiply Read
interpol the 2 factors can get the run time after power-on. only
ation
times
after i.e. R1009=1000, and System Data No. 4=3000, means that the controller has
power- been powered-on for 3 seconds.
on

R1010 Cutting Machining time per cycle, unit: second. Not retained after power-off. Read
time per only
cycle

R1011 Accumul Accumulating machining time, unit: second. Value reserved when power off, Read
ate value can be reset to 0 by user on HMI manually. only
cutting
time

CNC and PLC Interface – 116

 机床产品/Machine Tool Products
–
PLC Interface.

R1012 Power- Power-on time, unit: second. Value not-reserved after power off. Read
on only
time_1

R1013 Accumul Accumulated power-on time, unit: second. Value reserved after power-off. Read
ate only
power-
on time

R1014 Installati Installation cutting time for total, unit: hour. Value reserved after power-off, can Read
on only be cleared at the 1st installation. only
cutting
time

R1015 Power- Power-on time, unit: hour. Value not-reserved after power-off. Read
on only
time_2

R1016 System YYYYMMDD Read

date YYYY: Year; MM: Month; DD: Day only

R1017 System HHMMSS Read

time HH: Hour; MM: Minute; SS: Second only

R1018 Cutting Cutting time of last machining part, update after a part (program) is finished, Read
time per unit: ms. value not-reserved after power-off. only
cycle

R1019 PLC PLC Version, format is ##,##. Read/

Version Write
R1019=101 means V1,01
R1019=1020 means V10.20.

R1020 PLC File R1020 allowed file number of PLC file system. Write
~1023 System only
R1021 set store data width, unit is number of register.
R1022 set store data height, unit row number.
R1023 set the starting address of file system.
Control format as follow:

CNC and PLC Interface – 117

 机床产品/Machine Tool Products
–
PLC Interface.

R1024 User Mill: Used for auto tool center & tool height measure function; Read/
~R103 define/ Write
X Axis: R1024~R1026
2 System
Y Axis: R1027~R1029
use
Z Axis: R1030~R1032
Lathe: User-Defined Registers

R2050 User When Pr3810 is set to 0, these registers are user defined; when Pr3810 is set to 1, Read
~R209 define/ these registers are used by system. only
0 System
For details, please refer to Pr3810 *Paralleled executing multiple M code in one
use
block.

R2091 User User defined Read/

~R209 define Write
9

R2100 User When Pr3228 'Enable tool manager' =0, these registers are user-defined; Read/
~R310 define/ when Pr3228=1, registers are used by HMI, and HMI system will auto load or save Write
0 System to Registry Table 2100~3100.
use

R3101 User User defined Read/

~R409 define Write
5

CNC and PLC Interface – 118

 机床产品/Machine Tool Products
–
PLC Interface.

R4096 Accumul G01, G02, G03 look-ahead accumulated length ( unit : mm ) (Effective version:
~R409 ate look- 10.118.12 and above )
9 ahead
length R4096 : 1st path accumulated length

R4097 : 2nd path accumulated length

R4098 : 3rd path accumulated length

R4099 : 4th path accumulated length

Note 1 : Maximum Accumulated length is 2147483647 (unit: mm)

Note 2 : Stop to accumulate length under Feedhold and Emergency stop.
Note 3 : After reset and Emergency stop, clear the accumulator.
Note 4 : M30 will clear the accumulator
Note 5 : When executing the M Code of Workpiece Counter( Pr3804 ), clear clear
the accumulator of all paths.
Note 6 : Using M99 to repeat cycleing, the accumulated length will not be clear.
Unless Pr3804 is 99 ( Note 5 ).
Note 7 : Special Situation ( Insert Program、Tool break retract、Feedhold Point
Retract 、Tool Retraction )
1. Insert Program : Continue to accumulate when executing sub-program.
2. Tool break retract : Accumulator only starts on the middle of the program,
user can use #1048, #1052 to evaluate remain time.
3. Feedhold Point Retract : Stop to accumulate under Feedhold. Restart to
accumulate after cycling start. The length of tool back will not accumulate.
4. Tool Retraction : Tool Retraction ( that is, the moment between Tool retract
and recover ) will not accumulate length.

R4100 Reserve System reserved area

~R500 d for
0 CNC

R5001 Axis R5001: 1st axis following error. Read

~R501 Followin only
8 g Error R5002: 2nd axis following error.
so on and so forth..

R5021 Spindle Spindle maximum cutting speed Read

~R502 Max only
R5021 is the spindle of 1st path.
4 Cutting
R5022 is the spindle of 2nd path.
Speed
R5023 is the spindle of 3rd path.
R5024 is the spindle of 4th path.

CNC and PLC Interface – 119

 机床产品/Machine Tool Products
–
PLC Interface.

R5025 Reserve System reserved area

~R502 d for
8 CNC

R5029 Modbus Modbus Slave Error Code. When the slave is controller, this error code can be Read
Slave used for troubleshooting. only
Error
For Modbus TCP slave, it can use R5303 for more information.
Code
0：Slave (Server) activate success
1：Slave (Server) activate failure
2：Invalid Port
3：Invalid Station ID
4：Incorrect packet length
5：Incorrect packet content
6：Data confirmation error (CRC error)
7：Machining file upload abort command not received
8：Machining file read error
9：Response return failure

CNC and PLC Interface – 120

 机床产品/Machine Tool Products
–
PLC Interface.

R5030 Modbus When R5030.0 is set to disabled, PLC Modbus component communication use Write/
Protocol the set value of Pr39xx (COM2: Pr3941~Pr3950, COM3: Pr3961~ Pr3970) Read
Setup
b0 Enable Modbus protocol Disable: 0
setting Enabled: 1

b1 Data length 7 bit: 0

8 bit: 1

b3b2 Polarity Bit No: 00

Odd Corresponding: 01
Even Corresponding: 11

b4 Stop Bit 1 bit: 0

2 bit: 1

b8b7b6b5 Baud Rate 2400 bps：0000

4800 bps：0001
9600 bps：0010
19200 bps：0011
38400 bps：0100
57600 bps：0101
115200 bps：0110
230400 bps：0111
460800 bps：1000
912600 bps：1001

b9~b31 System reserved area (do not use)

Communication Format R5030 setting example:

Baud Rate "9600"/Stop bit "1"/Polarity Bit "None"/Data length "8"/Enable "1"
b8b7b6b5=0010 / b4 =0 / b3b2 =00 / b1 =1 / b0 =1
R5030=001000011(2) → Binary format should be converted to decimal format,
R5030=67(10)

CNC and PLC Interface – 121

 机床产品/Machine Tool Products
–
PLC Interface.

R5031 1st Serial Absolute value of Serial MPG Pulse Count, corresponds to M3 IO 1st station MPG Read
MPG Pul pulse feedback signal. Only
se Count
After software version 10.118.13, when activating the customized IO chart (Pr5
*I_O board type=100), it’s able to modify the corresponding initial point R at the
I/O chart page and not using R5031~R5033.

R5032 2nd As above, corresponds to MPG pulse feedback signal of M3 IO 2nd station. Read
Serial Only
MPG Pul
se Count

R5033 3rd Serial As above, corresponds to MPG pulse feedback signal of M3 IO 3rd station. Read
MPG Only
Pulse
Count

R5034 Reserve Serial MPG Function Reserved Area

~R503 d for
8 Serial
MPG

CNC and PLC Interface – 122

 机床产品/Machine Tool Products
–
PLC Interface.

R5039 Modbus When the master is controller, this error code can be used for troubleshooting.
Error
Modbus Error Code Instruction
Code
R5039 Detail

0 Success

1 Function Code error

2 Address error

3 Data Value error - Data value is defined invalid by Slave

4 Slave Device error

5 Confirm Acknowledge (ACK), when Slave defined longer

process time is needed, then return ACK to prevent
timeout.

6 Slave Device Busy

8 Memory Parity error

10 Gateway Path Unavailable

11 Gateway target Device failed to Respond

245 Non-supported Function Code

246 Modbus Packet format error

247 The COM Port assigned by R5040 is incorrect.

248 Server busy, halt communication command.

249 Data confirmation error (CRC error)

250 TimeOut error

251 Read COM Port error

CNC and PLC Interface – 123

 机床产品/Machine Tool Products
–
PLC Interface.

R5039 Detail

252 Write COM Port error

253 Open COM Port error

254 Unknown error

R5040 Modbus Modbus COM Port is used to set up the actual wirings.
COM If the hardware is SUPER/10/20/200, the COM Port is 3 (R5040=3);
Port If it is ARM series controller (exclude 81R series), the COM Port is 2 (R5040=2).
If it is 81R series controller, it does not support this function.
COM Port is Modbus TCP when set to 9, it would be able to transmit data through
the Internet (LAN), the specifications are the same as Modbus RS485, and
differences are:
1. Controller client (Master) and the connecting device server (Slave) should be
under the same domain.
2. The station ID of the connecting device server (Slave) should set to be the
same as the 4thdigit of IP.
i.e. If the IP is 192.168.1.5, the station ID should set to be 5.
3. Can connect at most 2 server (Slave) devices.
4. The communication error timeout can be set in Pr 3971.

R5041 Reserve Syntec Reserved Area

~R506 d for
0 CNC

R5061 A/D When Pr3261~Pr3263 =n004 (n: card station number), R5061~R5066 mapping to Read
~R508 value 1st~6th DA port on expansion card of Syntec Servo Drive Embedded Controller. only
0 (Effective version: 10.116.36I, 10.116.41, 10.117.41)

R5081 Thermal Pre-defined zone for Thermal value, reserve 20 channels Read
~R510 value only
0

R5101 Axis R5101: 1st axis index counter Read

~R511 Index R5102: 2nd axis index counter only
8 Counter so on and so forth...

CNC and PLC Interface – 124

 机床产品/Machine Tool Products
–
PLC Interface.

R5121 Accumul Axis corresponding register value +1 whenever an index signal is read. Read
~R513 ated only
8 Total R5121: 1staxis total index counts
Index R5122: 2ndaxis total index counts
Signal
Counts so on and so forth...

R5139 Reserve Reserved for system

~R514 d for
0 CNC

R5141 Spindle Spindle Torque Load: actual torque output of motor, unit % of rated torque. Read
~R515 Torque only
0 Load R5141: 1st spindle torque load
R5142: 2nd spindle torque load
...
R5150: 10th spindle torque load
Note 1: The function only works for serial bus communication.
Note 2: Supporting Version 10.116.9 and above.
Note 3: For the supporting versions and brands of EtherCAT serial, Refer to
EtherCAT驱动器应用手册#主轴与轴向负载率.
Note 4: For Panasonic RTEX (A6N) set driver parameter Pr7.34=18,
supporting versions refer to RTEX驱动器应用手册.
Note 5: When spindle type is inverter spindle (Pr1791~ = 0, 5), this value will be 0.

R5151 Axial Axial Torque Load: actual torque output of motor, unit % of rated torque. Read
~R516 Torque
8 Load R5151: 1st axis (X) torque load
R5152: 2nd axis (Y) torque load
so on and so forth...
Note 1: The function only works for serial bus communication.
Note 2: Supporting Version 10.116.15 and above.
Note 3: Please refer to EtherCat driver application manual for the supporting
versions and brands of EtherCat serial PLC.
Note 4: For Panasonic RTEX (A6N) set driver parameter Pr7.34=18,
supporting versions refer to RTEX驱动器应用手册

CNC and PLC Interface – 125

 机床产品/Machine Tool Products
–
PLC Interface.

R5171 Axial Torque limit ratio, unit thousands (1/1000) of rated torque. The Registers =0 Write
~R518 Rated means the axis is under maximum torque for position control. /Read
8 Torque
Limit R5171: 1st axis (X) torque limit ratio
Permille R5172: 2nd axis (Y) torque limit ratio
so on and so forth..
Note 1: The function only supports
1. YASKAWAM2/M3
2. SYNTECM3
3. EtherCAT serial supporting versions and brand, ref. EtherCAT驱动器应用手
册
Note 2:To activate the function, enable the torque limitation function by setting
driver parameters and restart the driver.
Note 3: If R5171~5188 are not 0, both Pulse and Serial System do not protect the
loss pulse and tracking error.
Note4: Supporting version: 10.116.20, 10.117.21 and above
Note5: Current supporting modes are NC Axis Position Mode, Spindle
Orientation Mode (C61), Spindle Speed Mode (C64), Spindle C Axis Mode (C63)

R5189 Reserve Reserved for system

~R519 d for
0 CNC

R5191 Velocity Velocity FeedForward under Axis Position Mode, unit: um/sec. Read/
~R520 FeedFor Write
8 wardund R5191 is the 1st axis Velocity FeedForward under Axis Position Mode.
er Axis R5192 is the 2nd axis Velocity FeedForward under Axis Position Mode.
Position
Mode so on and so forth…...
Note1: The function only supports YASKAWA M3 and Panasonic RTEX.
Note2: Loss pulse and tracking error won’t be protected when using this
function.
Note3: YASKAWA M3 supporting version should be 10.116.51, 10.117.51 and
above.
Note4: Panasonic RTEX supporting version should be 10.118.12I, 10.118.17 and
above, please refer to RTEX Driver Application Manual(CHT) for related
parameters settings of RTEX velocity feedforward.

R5211 Unbalan Read

ce- Only
Induced
Accelera
tion of
Spindle

CNC and PLC Interface – 126

 机床产品/Machine Tool Products
–
PLC Interface.

R5212 Unbalan Read

ce- Only
Induced
Velocity
of
Spindle

R5213 Unbalan Read

ce- Only
Induced
Displace
ment of
Spindle

R5214 Reserve System Reserved Area

~R529 d for
0 CNC

R5291 2nd It’s able to monitor other driver signals (Torque Limit or Brake signal) Read
Driver IO by Pr3266~Pr3267 Select the first set of driver signal to be monitored. Only
Signal,
Pr3267 = 1, R5291.1~R5291.18 corresponds to the torque arrival signal of the 1st
default
as ~18th axis, the Bit becomes 1 when the torque arrives the limit value.
external Pr3267 = 2, R5291.1~R5291.18 corresponds to the EXT1 signal of the 1st ~18th
latch axis, the Bit becomes 1 when the driver receives the EXT1 input signal.。
signal
(External Pr3267 = 3，R5291.1~R5291.18corresponds to the Brake signal of the 1st~18th
latch 1 axis, the Bit becomes 1 when the driver activates the brake..
input)
When applying high speed function G31, it would be able to monitor the signal
with R value and adjust it more easily if the signal resource of G31 is set up to
come from driver EXT1.
Note1: Supporting Version 10.116.36Y, 10.116.51, 10.117.51 and above
Note2: Please refer to R30 for the signal state supported by drivers from each
brand.

R5292 Reserve System Reserved Area

~R530 d for
0 CNC

CNC and PLC Interface – 127

 机床产品/Machine Tool Products
–
PLC Interface.

R5301 Modbus • Supporting Version：10.118.46F, 10.118.48Q, 10.118.52K, 10.118.56E,

~R530 TCP 10.118.60, and above
5 Slave • Modbus TCP Slave connection diagnosis function for using CNC as Modbus
connecti TCP Slave
on
diagnosi R function describtion Reading/
s Writing
function Regulations
for the (HMI、PLC、
first MACRO)
client
R5301 The Forth • must in range of read/write
Number of 1~254，
Modbus TCP otherwise it will
Master IP not be valid
• R5302~R5303 will
be valid after
setting R5301

CNC and PLC Interface – 128

 机床产品/Machine Tool Products
–
PLC Interface.

R function describtion Reading/

Writing
Regulations
(HMI、PLC、
MACRO)

R5302 Modbus TCP • When the idle read/write

Master Idle time of Modbus
Time TCP Master out
of the value of
R5302, CNC will
disconnect with
client
automatically
• must in range of
1~65535，unit：
second
• if the
input
value of
R5302 is
smaller
than 1，
then
R5302 will
be set by
1
• if the
input
value of
R5302 is
over
65535，
then
R5302 will
be set by
65535

CNC and PLC Interface – 129

 机床产品/Machine Tool Products
–
PLC Interface.

R function describtion Reading/

Writing
Regulations
(HMI、PLC、
MACRO)

R5303 Modbus TCP • Display the only read

Master connection state
Connection of Modbus TCP
State Master
• bit0:
connectio
n state
OFF:
disconnec
t、ON:
connect
• bit1~31:
reserved,
set by OFF

R5304~R reserved
5305

R5306 Reserve for Modbus TCP Slave

~R535 d
0

R5351 Reserve System Reserved Area

~R587 d for
9 CNC

R5880 Cruise Axis Switch between Positioning Control Mode and Gap Control Mode
Control
0: Switch back to Positioning Control Mode
Switch
1: Switch the 1st axis to Gap Control Mode

2: Switch the 2nd axis to Gap Control Mode

...
so on and so forth.

R5881 Target Cruise Control Mode Target Capacitance (count: 0~500,000)

Capacita
nce

CNC and PLC Interface – 130

 机床产品/Machine Tool Products
–
PLC Interface.

R5882 Tracing Cruise Control Mode Tracing Slope (pulse/count: -500,000~500,000)

Slope

R5883 Check ~10.118.28M, 10.118.36: Cruise Control Mode Position Check Window (BLU:
Window 0~10,000)
/ Max
10.118.28N, 10.118.37 and above: Max Capacitance(count: -32,768~32,767), 1
Capacita
Unit equals 1000 Units of R5881; Drive version must be 2.15.0, 2.14.105, 3.0.0 and
nce
above.

R5884 Capacita ~10.118.28M, 10.118.36:Capacitance Threshold Value (count: 0~500,000)

nce
10.118.28N, 10.118.37 and above: Min Capacitance(count: -32,768~32,767), 1
Threshol
Unit equals 1000 Units of R5881; Drive version must be 2.15.0, 2.14.105, 3.0.0 and
d/
above.
Min
Capacita
nce

R5885 Cruise Cruise Control Axial Status

Control
0: Not In Cruise Control Mode
Status
1: In Cruise Control Mode

R5886 Cruise in Cruise Control Status

Position
0: Cruise control unfinished/not support
1: Cruise control finished

R5887 Increme Increment Position Limit (BLU: -999,999~999,999)

nt
Position
Limit

R5888 Reserve System Reserved Area

~R589 d for
0 CNC

R5891 Coordin Combined feedrate FEEDBACK of axis group, unit LIU/min. Read
~R589 ate
4 Feedrate R5891: Combined feedrate of the 1st path
Feedbac R5892: Combined feedrate of the 2nd path
k R5893: Combined feedrate of the 3rd path
R5894: Combined feedrate of the 4th path

CNC and PLC Interface – 131

 机床产品/Machine Tool Products
–
PLC Interface.

R5895 Reserve Reserved for system

~R590 d for
0 CNC

R5901 Coordin Combined feedrate COMMAND of axis group, unit: LIU/min. Read
~R590 ate
4 Feedrate R5901: Combined feedrate of the 1st path
Comma R5902: Combined feedrate of the 2nd path
nd R5903: Combined feedrate of the 3rd path
R5904: Combined feedrate of the 4th path

R5905 Reserve System Reserved Area

~R591 d for
0 CNC

R5911 Robot Robot Path Actual Speed Command Value, unit: LIU/s Read
~R593 Coordin
R5911: Shows the maximum single axis speed percentage the internal axis of the
0 ate
Feedrate 1st path can reach (unit: 0.001%)
Comma R5912: Shows the linear direction feeding speed of the 1st path end point.
nd
R5913: Shows the rotary direction feeding speed of the 1st path end point.
R5914: Shows the maximum single axis speed percentage the external axis of the
1st path can reach (unit: 0.001%).
R5915: Reserved.
Each path provides 5 R values, and so on to R5930.

R5931 Reserve System Reserved Area

~5996 d for
CNC

R5997 Preview 9: Syntec customer service staff Read

Manager 99: Machine Manufacturer
Classfica 100: End-User Manager
tion 101: End-User Operator
999: Not Logged In
Effective version 10.116.10 and above

R5998 Backgro Register for PLC customized Image ACTION Read/

und Write
Action

CNC and PLC Interface – 132

 机床产品/Machine Tool Products
–
PLC Interface.

R5999 Tapping Max. Z axis to spindle following error under rigid/rapid tapping Read
Maximu
m
Tracking
Error

R6000 F-RAM F-RAM memory for user self defined Read/

~R799 memory Write
9 for user
define

R8000 MLC R8001~R8500 correspond to System parameter No.5001 ~ No.5500. Read

~R850 System
0 Paramet
er

R8500 Reserve Reserved for system

~R899 d for
9 CNC

R9000~R For robot Robot Kernel Operating Area (Not Customized Area) Read
9999 kernel /
Writ
e

R10000~ Reserved for Reserved for Vision system, ref. 3.7 system variables (R/L) instructions Read
R10499 Vision
Memory

R10500~ Reserved for Reserved for system

R14999 CNC

R15000~ Reserved for Reserved for Vision system, ref. 3.7 system variables (R/L) instructions
R15199 Vision
Processing

R15200~ Reserved for Reserved for Robot HMI

R15499 Robot HMI

R15500~ Reserved for Reserved for Vision system, ref. 3.7 system variables (R/L) instructions
R15999 Vision

CNC and PLC Interface – 133

 机床产品/Machine Tool Products
–
PLC Interface.

R16000 Trigger The register represents _CycleStart action on software panel. Read
Software
When user triggers _CycleStart on software panel, this register = 1.
Panel
_CycleStart
Action

R16001 Disable If this Register = 0, triggering _CycleStart on software panel will start Writ
Direct Cycle running program; e/
Start by Read
if this Register≠ 0, system will not start when triggering _CycleStart.
Software
Panel

R16002 Trigger The register represents _FeedHold action on software panel. Read
Software
When user triggers _FeedHold on software panel, this register = 1.
Panel
_FeedHold
Action

R16003 Disable If this Register = 0, triggering _FeedHold on software panel will pause Writ
Direct Feed running program; e/
Hold by Read
if this Register≠ 0, system will not pause when triggering _FeedHold.
Software
Panel

R16004 Trigger The register represents _Jog+Axis_1, _StopJog+Axis_1 action on Read

Software software panel.
Panel
When user triggers _Jog+Axis_1 on software panel, this register = 1.
_Jog+Axis_
When user triggers _StopJog+Axis_1 on software panel, this register = 0.
1,
_StopJog+A
xis_1 Action

R16005 Disable If this Register = 0, triggering _Jog+Axis_1 on software panel, system will Writ
Direct X Axis do X Axis JOG + ; e/
JOG + by Read
if this Register≠ 0, system will not do X Axis JOG + when triggering
Software
_Jog+Axis_1.
Panel

R16006 Trigger The register represents _Jog-Axis_1, _StopJog-Axis_1 action on software Read
Software panel.
Panel
When user triggers _Jog-Axis_1 on software panel, this register = 1.
_Jog-
When user triggers _StopJog-Axis_1 on software panel, this register = 0.
Axis_1,
_StopJog-
Axis_1
Action

CNC and PLC Interface – 134

 机床产品/Machine Tool Products
–
PLC Interface.

R16007 Disable If this Register = 0, triggering _Jog-Axis_1 on software panel, system will Writ
Direct X Axis do X Axis JOG - ； e/
JOG - by Read
if this Register≠ 0, system will not do X Axis JOG - when triggering _Jog-
Software
Axis_1.
Panel

R16008 Trigger The register represents _Jog+Axis_2, _StopJog+Axis_2 action on Read

Software software panel.
Panel
When user triggers _Jog+Axis_2 on software panel, this register = 1.
_Jog+Axis_
When user triggers _StopJog+Axis_2 on software panel, this register = 0.
2,
_
StopJog+Ax
is_2 Action

R16009 Disable If this Register = 0, triggering _Jog+Axis_2 on software panel, system will Writ
Direct Y Axis do Y Axis JOG + ; e/
JOG + by Read
if this Register≠ 0, system will not do Y Axis JOG + when triggering
Software
_Jog+Axis_2.
Panel

R16010 Trigger The register represents _Jog-Axis_2, _StopJog-Axis_2 action on software Read
Software panel.
Panel
When user triggers _Jog-Axis_2 on software panel, this register = 1.
_Jog-
When user triggers _StopJog-Axis_2 on software panel, this register = 0.
Axis_2 ,
_StopJog-
Axis_2
Action

R16011 Disable If this Register = 0, triggering _Jog-Axis_2 on software panel, system will Writ
Direct Y Axis do Y Axis JOG - ； e/
JOG - by Read
if this Register≠ 0, system will not do Y Axis JOG - when triggering _Jog-
Software
Axis_2.
Panel

R16012 Trigger The register represents _Jog+Axis_3, _StopJog+Axis_3 action on Read

Software software panel.
Panel
When user triggers _Jog+Axis_3 on software panel, this register = 1.
_Jog+Axis_
When user triggers _StopJog+Axis_3 on software panel, this register = 0.
3,
_StopJog+A
xis_3 Action

CNC and PLC Interface – 135

 机床产品/Machine Tool Products
–
PLC Interface.

R16013 Disable If this Register = 0, triggering _Jog+Axis_3 on software panel, system will Writ
Direct Z Axis do Z Axis JOG + ; e/
JOG + by Read
if this Register≠ 0, system will not do Z Axis JOG + when triggering
Software
_Jog+Axis_3.
Panel

R16014 Trigger The register represents _Jog-Axis_3, _StopJog-Axis_3 action on software Read
Software panel.
Panel
When user triggers _Jog-Axis_3 on software panel, this register = 1.
_Jog-
When user triggers _StopJog-Axis_3 on software panel, this register = 0.
Axis_3 ,
_StopJog-
Axis_3
Action

R16015 Disable If this Register = 0, triggering _Jog-Axis_3 on software panel, system will Writ
Direct Z Axis do Z Axis JOG - ; e/
JOG - by Read
if this Register≠ 0, system will not do Z Axis JOG - when triggering _Jog-
Software
Axis_3.
Panel

R16016~ Trigger Same as above Read

R16067 Software
Panel
_Jog+/-
Axis_4~16 ,
_StopJog+/-
Axis_4~16
Action

Disable Writ
Direct e/
4th~16th Read
Axis JOG + /
- by
Software
Panel

R16068 Trigger The register represents _MPGSimuOn, _MPGSimuOff action on software Read
Software panel.
Panel
When user triggers _MPGSimuOn on software panel, this register = 1.
_MPGSimu
When user triggers _MPGSimuOff on software panel, this register = 0.
On , _MPGSi
muOff
Action

CNC and PLC Interface – 136

 机床产品/Machine Tool Products
–
PLC Interface.

R16069 Disable If this Register = 0, triggering _MPGSimuOn on software panel, system Writ
Direct MPG will enable MPG Simulation ; e/
Simulation Read
if this Register≠ 0, system will not enable MPG Simulation when
by Software
triggering _MPGSimuOn.
Panel

R16070 Trigger The register represents _SetMachinePosAxis_1 action on software panel. Read
Software
When user triggers _SetMachinePosAxis_1 on software panel, this register
Panel
= 1.
_SetMachin
ePosAxis_1
Action

R16071 Disable If this Register = 0, triggering _SetMachinePosAxis_1 on software panel, Writ

Direct Set X system will Set X Axis Machine Position ; e/
Axis Read
if this Register≠ 0, system will not Set X Axis Machine Position when
Machine
triggering _SetMachinePosAxis_1.
Position by
Software
Panel

R16072 Trigger The register represents _SetMachinePosAxis_2 action on software panel. Read
Software
When user triggers _SetMachinePosAxis_2 on software panel, this register
Panel
= 1.
_SetMachin
ePosAxis_2
Action

R16073 Disable If this Register = 0, triggering _SetMachinePosAxis_2 on software panel, Writ

Direct Set Y system will Set Y Axis Machine Position ; e/
Axis Read
if this Register≠ 0, system will not Set Y Axis Machine Position when
Machine
triggering _SetMachinePosAxis_2.
Position by
Software
Panel

R16074 Trigger The register represents _SetMachinePosAxis_3 action on software panel. Read
Software
When user triggers _SetMachinePosAxis_3 on software panel, this register
Panel
= 1.
_SetMachin
ePosAxis_3
Action

CNC and PLC Interface – 137

 机床产品/Machine Tool Products
–
PLC Interface.

R16075 Disable If this Register = 0, triggering _SetMachinePosAxis_3 on software panel, Writ

Direct Set Z system will Set Z Axis Machine Position ; e/
Axis Read
if this Register≠ 0, system will not Set Z Axis Machine Position when
Machine
triggering _SetMachinePosAxis_3.
Position by
Software
Panel

R16076~ Trigger Same as above Read

R16101 Software
Panel
_SetMachin
ePosAxis_4
~16th
Action

Disable Writ
Direct Set e/
4th~16th Ax Read
is
Machine
Position by
Software
Panel

R16102 Trigger The register represents _ManualControlOnAxis_1 , Read

Software _ManualControlOffAxis_1 action on software panel.
Panel
When user triggers _ManualControlOnAxis_1 on software panel, this
_ManualCo register = 1.
ntrolOnAxis
When user triggers _ManualControlOffAxis_1 on software panel, this
_1 ,
register = 0.
_ManualCo
ntrolOffAxis
_1
Action

R16103 Disable If this Register = 0, triggering _ManualControlOnAxis_1 on software Writ

Direct X Axis panel, system will enable X Axis MANUAL CONTROL ; e/
MANUAL Read
if this Register≠ 0, system will not enable X Axis MANUAL CONTROL when
CONTROL
triggering _ManualControlOnAxis_1.
by Software
Panel

CNC and PLC Interface – 138

 机床产品/Machine Tool Products
–
PLC Interface.

R16104 Trigger The register represents _ManualControlOnAxis_2 , Read

Software _ManualControlOffAxis_2 action on software panel.
Panel
When user triggers _ManualControlOnAxis_2 on software panel, this
_ManualCo register = 1.
ntrolOnAxis
When user triggers _ManualControlOffAxis_2 on software panel, this
_2 ,
register = 0.
_ManualCo
ntrolOffAxis
_2
Action

R16105 Disable If this Register = 0, triggering _ManualControlOnAxis_2 on software Writ

Direct Y Axis panel, system will enable Y Axis MANUAL CONTROL ; e/
MANUAL Read
if this Register≠ 0, system will not enable Y Axis MANUAL CONTROL when
CONTROL
triggering _ManualControlOnAxis_2.
by Software
Panel

R16106 Trigger The register represents _ManualControlOnAxis_3 , Read

Software _ManualControlOffAxis_3 action on software panel.
Panel
When user triggers _ManualControlOnAxis_3 on software panel, this
_ManualCo register = 1.
ntrolOnAxis
When user triggers _ManualControlOffAxis_3 on software panel, this
_3 ,
register = 0.
_
ManualCont
rolOff
Axis_3
Action

R16107 Disable If this Register = 0, triggering _ManualControlOnAxis_3 on software Writ

Direct Z Axis panel, system will enable Z Axis MANUAL CONTROL ; e/
MANUAL Read
if this Register≠ 0, system will not enable Z Axis MANUAL CONTROL when
CONTROL
triggering _ManualControlOnAxis_3.
by Software
Panel

CNC and PLC Interface – 139

 机床产品/Machine Tool Products
–
PLC Interface.

R16108~ Trigger Same as above Read

R16133 Software
Panel
_ManualCo
ntrolOnAxis
_4~16 ,
_ManualCo
ntrolOffAxis
_4~16
Action

Disable Writ
Direct e/
4th~16th Read
Axis
MANUAL
CONTROL
by Software
Panel

R16134 Trigger The register represents _Reset action on software panel. Read
Software
When user triggers _Reset on software panel, this register = 1.
Panel
_Reset
Action

R16135 Disable If this Register = 0, triggering _Reset on software panel, system will Writ
Direct Reset RESET; e/
Read
by Software if this Register≠ 0, system will not RESET when triggering _Reset.
Panel

R16136 Trigger The register represents _SingleBlockOn, _SingleBlockOff action on Read

Software software panel.
Panel
When user triggers _SingleBlockOn on software panel, this register = 1.
_SingleBloc
When user triggers _SingleBlockOff on software panel, this register = 0.
kOn,
_SingleBloc
kOff
Action

CNC and PLC Interface – 140

 机床产品/Machine Tool Products
–
PLC Interface.

R16137 Disable If this Register = 0, triggering _SingleBlockOn on software panel, system Writ
Direct will enable Single Block Stop; e/
Single Read
if this Register≠ 0, system will not enable Single Block Stop when
Block
triggering _SingleBlockOn.
by Software
Panel

R16138 Software The register represents the argument N of _Mode_N action on software Read
Panel Mode panel, and the action switch modes base on value of N:
Selection
1: Edit
2: Auto
3: MDI
4: Jog
5: InJog
6: MPG
7: Home
I.e.: Triggering _Mode_2 will set the register =2, and switch to Auto Mode.

R16139 Disable If this Register = 0, triggering _Mode_N on software panel, system will Writ
Direct Chang switch Modes; e/
e Mode Read
if this Register≠ 0, system will not switch Modes when triggering
Selection by
_Mode_N.
Software
Panel

R16140 Software The register represents the argument N of _IncrementFeed_N action on Read
Panel software panel, which decides the magnify ratio of 1st MPG & InJog
Increment
Example: Triggering _IncrementFeed_10, this register =10 and the
Feed
magnify ratio become x10. The single movement of InJog increased from
0.001 to 0.10.

R16141 Disable If this Register = 0, triggering _IncrementFeed_N on software panel, Writ

Direct system will adjust Magnify Ratio of 1st MPG & InJog; e/
Change Read
if this Register≠ 0, system will not adjust Magnify Ratio of 1st MPG &
Increment
Injog when triggering _IncrementFeed_N.
Feed by
Software
Panel

R16142 Software The register represents the argument N of _SpindleOverride_N action on Read
Panel software panel, which decides the Override of Spindle.
Spindle
Example: Triggering _SpindleOverride_10, this register = 50 and the
Override
Spindle Override become 50%.

CNC and PLC Interface – 141

 机床产品/Machine Tool Products
–
PLC Interface.

R16143 Disable If this Register = 0, triggering _SpindleOverride_N on software panel, Writ

Direct Chang system will adjust spindle override; e/
e Spindle Read
if this Register≠ 0, system will not adjust spindle override when
Override by
triggering _SpindleOverride_N.
Software
Panel

R16144 Software The register represents the argument N of _FeedrateOverride_N action on Read
Panel software panel, which decides the Override of G01.
Feedrate
Example: Triggering _FeedrateOverride_50, this register = 50 and the
Override
G01 Override become 50%.

R16145 Disable If this Register = 0, triggering _FeedrateOverride_N on software panel, W/R

Direct system will adjust G01 override;
Change
if this Register≠ 0, system will not adjust G01 override when triggering
Feedrate
_FeedrateOverride_N.
Override by
Software
Panel

R16146 Software The register represents the argument N of _JOGOverride_N action on Read
Panel JOG software panel, which decides the Override of Jog.
Override
Example: Triggering _JOGOverride_50, this register = 50 and the override
become 50%.

R16147 Disable If this Register = 0, triggering _JOGOverride_N on software panel, system Read
Direct will adjust Jog override; /
Change JOG Writ
if this Register≠ 0, system will not adjust Jog override when triggering
Override by e
_JOGOverride_N.
Software
Panel

R16148 Software The register represents the argument N of _RapidTravelOverride_N Read

Panel Rapid action on software panel, which decides the Override of G00.
Traverse
Example: Triggering _RapidTravelOverride_50, this register = 50 and the
Override
G00 Override become 50%.

R16149 Disable If this Register = 0, triggering _RapidTravelOverride_N on software Read

Direct panel, system will adjust G00 override; /
Change Writ
if this Register≠ 0, system will NOT adjust G00 override when triggering
Rapid e
_RapidTravelOverride_N.
Traverse
Override by
Software
Panel

CNC and PLC Interface – 142

 机床产品/Machine Tool Products
–
PLC Interface.

R16150~ Reserved for Reserved for Software Panel Function

R16999 Software
Panel

R17000 Reserved for Reserved for Laser Marking Function

Laser
Marking

R17001 SCANNER_O X Offset of laser marking galvanometer module, unit : µm. Read
FFSET /
XOffset Writ
e

R17002 SCANNER_O Y Offset of laser marking galvanometer module, unit : µm. Read
FFSET Y /
Offset Writ
e

R17003 Reserved for Reserved for expansion of Z offset.

Laser
Marking

R17004 SCANNER_A Galvonometer module scanner mirror rotation angle，unit: 10^-6 deg. Read
NGLE Angle /
angle > 0 rotate counter-clockwise.
Writ
angle < 0 rotate clockwise.
e

R17005 MAX laser Maximum laser frequency (unit: kHz) Rea

frequency( u d/
nit: kHz ) Writ
e

R17006 MIN laser Minimum laser frequency (unit: kHz) Rea

frequency( u d/
nit: kHz ) Writ
e

R17007 Laser delay Laser delay time ( unit: 0.1 ms) Rea
time ( unit: d/
0.1 ms ) Writ
e

CNC and PLC Interface – 143

 机床产品/Machine Tool Products
–
PLC Interface.

R17008 Laser mode Laser mode selection Rea

selection d/
0: Not selected
Writ
1: Auto Mode
e
2: Marking while data transmitting

R17009 Laser Laser program start running when the Register=1, and the Register is Read
Marking cleared to 0 when program starts. /
Control Writ
When the corresponding Bit ON, the corresponding function is triggered,
Interface e
and R17009 is automatically cleared to 0. (Do not trigger multiple functions
at once)
Bit 0: Trigger laser marking machining.
Bit 1: Trigger the laser marking reset. (C37 can also trigger a reset)

R17010 Laser end When the R value is 1, end the machining process of marking-while-data- Read
programmin transmitting, except under synchronous marking mode. /
g request Writ
After activated, system clear R-value with 0 automatically.
e

R17011 Enable Enable manual control of galvo motor Read

manual /
R17011= 0: Disabled
function for Writ
galvo meter R17011= 1: Enabled e

R17012 Enable Enable manual laser emitting Read

manual laser /
R17012 = 0: Enabled
energy Writ
R17012 = 1: Disabled e

R17013 Set manual Set manual laser frequency (unit: kHz) Read
laser /
frequency( u Writ
nit: kHz ) e

R17014~ Set manual Setup the manual jog for galvanometer scanner Read
R17016 jog for galvo /
R17014: Axis ID (1:X, 2: Y, 3: Z)
motor Writ
R17015: Magnify Ratio e
0: 0.1x
1: 1x
2: 10x
3: 100x
R17016: Basic Movement, unit: mdeg. Take the deviation value as the
current movement.

CNC and PLC Interface – 144

 机床产品/Machine Tool Products
–
PLC Interface.

R17018 Machining 0: Single interpretation of the machining file. Read

cycle mode 1: Repeat the interpretation of the machining file a limited number of /
times. Writ
2: Repeat the interpretation of the machining file indefinitely until the reset e
signal (Reset) is triggered.
3: Record mode for the small files (unsupported with 70SB)
4: Play mode for the small files (unsupported with 70SB)

R17019 Machining If R17018 is set to 1, the value specified by this R value is used as the counts Read
paths interp of repeated interpretations of the processing file. /
retation If R17018 is set to 1, and R17019 is set to a non-positive integer, cycle start Writ
repeat count will trigger the alarm LASERCTRL-006. e

R17020 Laser Setup laser marking feedrate override, override must be > 0 and ≤ 200％。 Read
marking /
R17020 = 100 means feedrate is100%;
override Writ
R17020 = 150 means feedrate is 150%.
e

R17021 Part Only applied in conveyer marking mode, an I Bit is used to detect whether Read
detecting the parts on the conveyer passed by, and the I Bit informs the kernel there /
trigger are parts passing by with R17021. Writ
signal e
When R17021 turns to 1 from 0 means there are parts being detected. The
laser kernel will set R17021 back to 0 automatically after receiving the
signal.

R17022 Part Only applied in conveyer marking mode, an I Bit is used to detect whether Read
detecting the parts on the conveyer passed by, and the I Bit informs macro there are /
trigger parts passing by with R17022. Writ
signal - e
When R17022 turns to 1 from 0 means there are parts being detected.
macro
Macro will send the marking data to kernel and set R17022 back to 0
automatically after receiving the signal.

R17023~ Laser Reserved for Laser Marking Functions Read

R17024 Marking /
Function Writ
Reserved e
Area

R17025 Laser Laser Marking Synchronous Mode/Tracking Mode Setup Read

Marking /
0: Disabled
Synchronou Writ
s Mode/ 1: Tracking Mode (Product Line) e
Tracking
Mode Setup

CNC and PLC Interface – 145

 机床产品/Machine Tool Products
–
PLC Interface.

R17026 Laser Laser Marking Synchronous Mode Setup Read

Marking /
0: Disp-Base
Synchronou Writ
s Mode 1: Time-Base e
Setup

R17027~ Laser Reserved for Laser Marking Functions Read

R17030 Marking /
Function Writ
Reserved e
Area

R17031~ Assign laser Assign Laser File Name, 10 R values reserved, maximum 39 bytes (Plus 1 Rea
R17040 file name ending character) d/
Writ
Example:
e
Macro :
@117031:= "Laser_Main"
Registers:
R17031'e''s''a''L'
R17032 'a''M''_''r'
R17033 '\0''n''i'

R17041~ Laser Source R17041: Set to 1, laser source switched to data transmission mode; set to Read
R17042 Pulse Width be 0, laser source data transmission mode off. /
Modulation Writ
R17042: Pulse width (unit: ns). Range limitation: 0~65535
e
The 71SA needs to use with the FC-LSMPW to connect to the first piece of
the first station.

R17043~ Reserved Reserved for Laser source pulse width setting

R17045 for Laser
source pulse
width
setting

R17046~ Reserved for Reserved for Laser Marking

R17099 Laser
Marking

R17100 Laser status Laser status Read

0：Not Ready
1：Ready
2：Processing
3：Manual

CNC and PLC Interface – 146

 机床产品/Machine Tool Products
–
PLC Interface.

R17101 Laser mode Laser mode Rea

d
0: Not selected
1: Auto Mode
2: Marking while data transmitting

R17103~ Reserved for Reserved for Laser Marking Function

R17109 Laser
Marking
Function

R17110 Laser energy Laser energy command (0~255) Read

command

R17111~ Laser galvo Laser galvanometer scanner axis command (unit: mdeg) Read
R17113 axis
command( u
nit: mdeg )

R17114~ Laser galvo Laser galvanometer scanner axis feedback command (unit: mdeg) These Read
R17116 axis Registers display command value if no feedback.
feedback( u
nit: mdeg )

R17117~ Reserved for Reserved for Laser Marking Read

R17119 Laser
Marking

R17120 Conveyor Conveyor Current Speed Read

Current
When the conveyor sensor being set as a normal encoder, it shows the
Speed
actual feedback; when being set as the virtual speed, it shows the virtual
conveyor speed.

R17121~ Laser Laser Marking Function Reserved Area Read

R17124 Marking
Function
Reserved
Area

R17125 Laser Laser Marking Synchronous Mode/Tracking Mode Setup Read

Marking
0: Disabled
Synchronou
s Mode/ 1: Tracking Mode (Product Line)
Tracking
Mode Setup

CNC and PLC Interface – 147

 机床产品/Machine Tool Products
–
PLC Interface.

R17126 Laser Current Laser Marking Synchronous Mode Status Read

Marking
0: Disp-Base
Synchronou
s Mode 1: Time-Base
Status

R17127~ Laser Laser Marking Function Reserved Area Read

R17150 Marking
Function
Reserved
Area

R17151 Laser Energy Decide the laser source type according to parameter 3402 and display the Read
Display laser energy of each laser source type corresponding R value, unit: %.
The corresponding R value of SPI is R880
The corresponding R value of IPG is R53

R17152 Manual The R value is related to the manual laser time of the controller, the laser Read
Laser On turns on when the R value is not 0, unit: second. /
Time Input Writ
e

R17153 Remaining The R value is related to the remaining manual laser time, the laser turns Read
Manual off when the R value is 0, unit: second.
Laser On
Time

R17154 Laser Energy Decide the laser source type according to parameter 3402 and fill the Read
Setup energy into corresponding R values. /
Writ
The corresponding R value of SPI is R880
e
The corresponding R value of IPG is R53

R17155 Part Rotary Set the rotary amount of laser marking, the original unit: 10^-6 deg, change Read
Angle Setup the rotary amount unit to deg. /
Writ
angle > 0 means rotating counterclockwise
e
angle < 0 means rotating clockwise

CNC and PLC Interface – 148

 机床产品/Machine Tool Products
–
PLC Interface.

R17156 Set the grid The grid point number on single side when calling G533 for Grid Distortion Read
point Correction Marking. /
number on Writ
i.e. When the value is 5, it means to mark a 5x5 grid points.
single side e
of Grid Since the kernel of the Grid Distortion Correction only accepts 3x3, 5x5,
Distortion 9x9. 17x17, 33x33, total 5 correction options, the value should better set to
Correction be 3,5,6,17,33.
Marking
(NxN)

R17157 Grid The unilateral length (mm) when calling G533 for Grid Calibration Marking. Read
Distortion /
Correction Writ
Marking e
Range Setup
(mm)

R17158 Maximum The maximum distortion amount of all grid points when doing vision Read
Distortion distortion measurements (um). /
Amount Writ
e

R17159 Host When R17159=1, it triggered C37 and run the sub-program O1111. The Read
stopped content of O1111 is controller send HMI_Reset action. /
slave device Writ
machining e
mechanism

R17160 Set manual Manual Laser Pulse Width Setup (Unit: ns) Read
laser pulse /
width (unit: Writ
ns) e

R17161~ Laser Laser Marking HMI System Reserved Area

R17200 Marking HMI
System
Reserved
Area

R17201~ Woodworkin 0: Empty, not processing, or being overwrite to 0 by PLC after reset. Read
R17210 g Drilling /
1: The station is ready for machining.
Machine Writ
Occupied R e
value
G54~G57
station cycle
start

CNC and PLC Interface – 149

 机床产品/Machine Tool Products
–
PLC Interface.

R17211 Woodworkin When system couldn’t find the R1720x file, unable to assign, the R value Read
g Station changes to x ( x= 1~4 ).
Alarm

R17212~ Woodworkin Woodworking Function Reserved Area

R17300 g Function
Reserved
Area

R17301~ Five-Axis Five-Axis Function Reserved Area

R17350 Function
Reserved
Area

R17351~ Laser Laser Cutting Process Parameters, CYC File. Read

R17400 Cutting /
Process Writ
Parameters e

R17401~ Laser Laser Cutting Servo Correction – Height Voltage Parameters, CYC File. Read
R17440 Cutting /
Servo Writ
Correction – e
Height
Voltage
Parameters

R17441~ Laser Laser Cutting Speed Power Chart, CYC File. Read
R17461 Cutting /
Speed Writ
Power Chart e

R17462~ Laser Laser Cutting Software Panel Parameters (Software Panel) Read
R17500 Cutting /
Software Writ
Panel e
Parameters
(Software
Panel)

R17501~ Laser Laser Cutting Power, Frequency, Servo PLC Calculating Area. Read
R17548 Cutting /
Power, Writ
Frequency, e
Servo PLC
Calculating
Area.

CNC and PLC Interface – 150

 机床产品/Machine Tool Products
–
PLC Interface.

R17549~ Laser Laser Cutting Customized Functions (Tube exchange, Process repeat, Read
R17556 Cutting Coordinate transformation) /
Customized Writ
Functions e
(Tube
exchange,
Process
repeat,
Coordinate
transformati
on)

R17557~ Laser Laser Cutting Function Reserved Area Read

R17600 Cutting /
Function Writ
Reserved e
Area

R17601~ High-Speed High-Speed Spindle Glass Milling Machine Reserved Area

R17699 Spindle
Glass Milling
Machine
Reserved
Area

R17700~ Reserved for System Reserved Area

R17999 CNC

R18000~ Vision Vision Reserved Area - ref 3.7 System Parameter(R/L) Instructions
R18999 Function
Reserved
Area

R19000~ Robot Robot Process Package Reserved Area

R19199 Process
Package
Reserved
Area

R19000~ Robot Robot Process Package Reserved Area

R19199 Process
Package
Reserved
Area

R19200~ Reserved for Reserved for system (Consider the robot data coherence when using)
R19999 CNC

CNC and PLC Interface – 151

 机床产品/Machine Tool Products
–
PLC Interface.

R20000~ User define User-defined

R65535

® marked components mean the signal or Register will be processed instantly.

CNC and PLC Interface – 152

 机床产品/Machine Tool Products
–
PLC Interface.

2 PLC Interface Integration-Axis & Spindle

• This page integrates PLC interface of axis and spindle related functions, so that the developers can improve
the search speed.
• For the detail of each component, please refers to PLC Interface.

Axis Spindle others

2.1 Command
Functio 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 18
n\Axis 0 1 2 3 4 5 6 7
ID

1 Axis Jog C6 C C C C C C C C C C C C C C C C C1
（+） 8 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 96
0 7 7 2 7 7 7 8 8 8 8 8 9 9 9
0 2 4 6 8 0 2 4 6 8 0 2 4

2 Axis Jog C7 C C C C C C C C C C C C C C C C C1
（-） 9 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 97
1 7 7 3 7 7 7 8 8 8 8 8 9 9 9
1 3 5 7 9 1 3 5 7 9 1 3 5

3 Axis C1 C C C C C C C C C C C C C C C C C2
MPG 6 1 1 2 2 1 2 2 2 2 2 2 2 2 2 2 2 28
Selectio 7 8 1 1 9 1 1 1 2 2 2 2 2 2 2 2
n 5 6 7 8 9 0 1 2 3 4 5 6 7

4 Set C2 C C C C C C C C C C C C C C C C C2
Machine 5 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 43
Position 6 7 3 3 8 3 3 3 3 3 3 3 3 4 4 4
0 1 2 3 4 5 6 7 8 9 0 1 2

5 Axis C3 C C C C C C C C C C C C C C C C C2
Manual 1 3 3 2 2 3 2 2 2 2 2 2 2 2 2 2 2 58
Control 2 3 4 4 4 4 4 4 5 5 5 5 5 5 5 5
（ 5 6 7 8 9 0 1 2 3 4 5 6 7
Monitor
Mode）

6 Over C5 C C C C C C C C C C C C C C C C C1
Travel 0 5 5 1 1 5 1 1 1 1 1 1 1 1 1 1 1 66
（+） 2 4 4 4 6 4 4 4 5 5 5 5 5 6 6 6
0 2 4 6 8 0 2 4 6 8 0 2 4

PLC Interface Integration-Axis & Spindle – 153

 机床产品/Machine Tool Products
–
PLC Interface.

Functio 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 18
n\Axis 0 1 2 3 4 5 6 7
ID

7 Over C5 C C C C C C C C C C C C C C C C C1
Travel 1 5 5 1 1 5 1 1 1 1 1 1 1 1 1 1 1 67
（-） 3 5 4 4 7 4 4 4 5 5 5 5 5 6 6 6
1 3 5 7 9 1 3 5 7 9 1 3 5

8 Axis C6 C C C C C C C C C C C C C C C C C2
Controll 6 6 6 2 2 6 2 2 2 2 2 2 2 2 2 2 2 73
ed by 7 8 6 6 9 6 6 6 6 6 6 6 6 7 7 7
PLC 0 1 2 3 4 5 6 7 8 9 0 1 2

9 Home C7 C C C C C C C C C C C C C C C C C2
Dog 9 8 8 2 2 8 2 2 2 2 2 2 2 2 2 2 2 13
Signal 0 1 0 0 2 0 0 0 0 0 0 0 0 1 1 1
0 1 2 3 4 5 6 7 8 9 0 1 2

10 Machine R6 R R R R R R R R R R R R R R R R R6
Lock 00 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 00
.0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 .1
1 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 0. 8
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7

11 Axis R6 R R R R R R R R R R R R R R R R R6
MPG 01 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 01
Simulati .0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 .1
on（PLC 1 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 1. 8
Axis） 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7

12 Prohibit R6 R R R R R R R R R R R R R R R R R6
Axis 03 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 03
Comma .0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 .1
nd 1 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 8
0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7

13 Machine R6 R R R R R R R R R R R R R R R R R6
Lock for 12 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 12
Positive .0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 .1
Directio 1 2. 2. 2. 2. 2. 2. 2. 2. 2. 2. 2. 2. 2. 2. 2. 2. 8
n 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7

PLC Interface Integration-Axis & Spindle – 154

 机床产品/Machine Tool Products
–
PLC Interface.

Functio 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 18
n\Axis 0 1 2 3 4 5 6 7
ID

14 Machine R6 R R R R R R R R R R R R R R R R R6
Lock for 13 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 6 13
Negative .0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 .1
Directio 1 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 3. 8
n 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7

2.2 Status
Func 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 17 18
tion\ 0 1 2 3 4 5 6
Axis
ID

1 Axis S S S S S S S S S S S S S S S S S1 S1
Busy 6 7 8 15 15 9 15 15 15 1 16 16 16 16 16 16 67 68
5 6 7 8 9 6 1 2 3 4 5 6
0

2 Axis S S S S S S S S S S S S S S S S S1 S1
Homi 16 17 18 14 14 19 14 14 14 1 14 14 14 14 15 15 52 53
ng 0 1 2 3 4 4 6 7 8 9 0 1
OK 5

3 Serv S S S S S S S S S S S S S S S S （only
o 17 17 17 17 17 17 17 17 17 1 18 18 18 18 18 18 support
Axis 1 2 3 4 5 6 7 8 9 8 1 2 3 4 5 6 16
Alar 0 axes ）
m

4 Axis R R R R R R R R R R R R R R R R R2 R2
Enab 20 20 20 20 20 20 20 20 20 2 20 20 20 20 20 20 0. 0.
led .0 .0 .0 .0 .0 .0 .0 .0 .0 0. .1 .1 .1 .1 .1 .1 17 18
1 2 3 4 5 6 7 8 9 1 1 2 3 4 5 6
0

PLC Interface Integration-Axis & Spindle – 155

 机床产品/Machine Tool Products
–
PLC Interface.

Func 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 17 18
tion\ 0 1 2 3 4 5 6
Axis
ID

5 Axis R R R R R R R R R R R R R R R R R6 R6
Move 61 61 61 61 61 61 61 61 61 6 61 61 61 61 61 61 11 11
ment 1. 1. 1. 1. 1. 1. 1. 1. 1. 1 1. 1. 1. 1. 1. 1. .1 .1
Flag 01 02 03 04 05 06 07 08 09 1. 11 12 13 14 15 16 7 8
1
0

6 M R R R R R R R R R R R R R R R R R6 R6
Code 62 62 62 62 62 62 62 62 62 6 62 62 62 62 62 62 29 29
Read 9. 9. 9. 9. 9. 9. 9. 9. 9. 2 9. 9. 9. 9. 9. 9. .1 .1
for 01 02 03 04 05 06 07 08 09 9. 11 12 13 14 15 16 7 8
PLC 1
Axis 0

7 M R R R R R R R R R R R R R R R R R6 R6
Code 63 63 63 63 63 63 63 63 63 6 63 63 63 63 63 63 30 30
Finis 0. 0. 0. 0. 0. 0. 0. 0. 0. 3 0. 0. 0. 0. 0. 0. .1 .1
h for 01 02 03 04 05 06 07 08 09 0. 11 12 13 14 15 16 7 8
PLC 1
Axis 0

2.3 Value
Func 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 1
tion\ 0 1 2 3 4 5 6 7 8
Axis
ID

1 Progr R7 R7 R7 R R R7 R R R R R R R R R R R R
am 21/ 22/ 23/ 7 7 26/ 7 7 7 7 7 7 7 7 7 7 7 7
Coor R2 R2 R2 2 2 R2 2 2 2 3 3 3 3 3 3 3 3 3
dinat 6 7 8 4 5 9 7 8 9 0 1 2 3 4 5 6 7 8
e

2 Mach R7 R7 R7 R R R7 R R R R R R R R R R R R
ine 41/ 42/ 43/ 7 7 46/ 7 7 7 7 7 7 7 7 7 7 7 7
Coor R3 R3 R3 4 4 R3 4 4 4 5 5 5 5 5 5 5 5 5
dinat 1 2 3 4 5 4 7 8 9 0 1 2 3 4 5 6 7 8
e

PLC Interface Integration-Axis & Spindle – 156

 机床产品/Machine Tool Products
–
PLC Interface.

Func 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 1
tion\ 0 1 2 3 4 5 6 7 8
Axis
ID

3 MPG R6 R6 R6 R R R6 R R R R R R R R R R R R
Com 41 42 43 6 6 46 6 6 6 6 6 6 6 6 6 6 6 6
mand 4 4 4 4 4 5 5 5 5 5 5 5 5 5
Ratio 4 5 7 8 9 0 1 2 3 4 5 6 7 8

4 G00/ R6 R6 R6 R R R6 R R R R R R R R R R R R
G01 61 62 63 6 6 66 6 6 6 6 6 6 6 6 6 6 6 6
Feedr 6 6 6 6 6 7 7 7 7 7 7 7 7 7
ate 4 5 7 8 9 0 1 2 3 4 5 6 7 8
Overr
ide
for
PLC
Axis

5 M R6 R6 R6 R R R6 R R R R R R R R R R R R
Code 81 82 83 6 6 86 6 6 6 6 6 6 6 6 6 6 6 6
Cont 8 8 8 8 8 9 9 9 9 9 9 9 9 9
ent 4 5 7 8 9 0 1 2 3 4 5 6 7 8
for
PLC
Axis

6 Axis R7 R7 R7 R R R7 R R R R R R R R R R R R
Veloc 01 02 03 7 7 06 7 7 7 7 7 7 7 7 7 7 7 7
ity 0 0 0 0 0 1 1 1 1 1 1 1 1 1
4 5 7 8 9 0 1 2 3 4 5 6 7 8

7 Axis R9 R9 R9 R R R9 R R R R R R R R R R R R
Temp 01 02 03 9 9 06 9 9 9 9 9 9 9 9 9 9 9 9
eratu 0 0 0 0 0 1 1 1 1 1 1 1 1 1
re 4 5 7 8 9 0 1 2 3 4 5 6 7 8
Com
pens
ation
Value

PLC Interface Integration-Axis & Spindle – 157

 机床产品/Machine Tool Products
–
PLC Interface.

Func 1 2 3 4 5 6 7 8 9 1 1 1 1 1 1 1 1 1
tion\ 0 1 2 3 4 5 6 7 8
Axis
ID

8 Hom R9 R9 R9 R R R9 R R R R R R R R R R R R
e Dog 61 62 63 9 9 66 9 9 9 9 9 9 9 9 9 9 9 9
Signa 6 6 6 6 6 7 7 7 7 7 7 7 7 7
l 4 5 7 8 9 0 1 2 3 4 5 6 7 8
Offse
t

9 Positi R9 R9 R9 R R R9 R R R R R R R R R R R R
on 81 82 83 9 9 86 9 9 9 9 9 9 9 9 9 9 9 9
Feed 8 8 8 8 8 9 9 9 9 9 9 9 9 9
back 4 5 7 8 9 0 1 2 3 4 5 6 7 8
Coun
ter

10 Follo R5 R5 R5 R R R5 R R R R R R R R R R R R
wing 001 002 003 5 5 006 5 5 5 5 5 5 5 5 5 5 5 5
Error 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 1 1 1 1 1 1 1 1 1
4 5 7 8 9 0 1 2 3 4 5 6 7 8

11 Index R5 R5 R5 R R R5 R R R R R R R R R R R R
Signa 121 122 123 5 5 126 5 5 5 5 5 5 5 5 5 5 5 5
l 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Coun 2 2 2 2 2 3 3 3 3 3 3 3 3 3
ter 4 5 7 8 9 0 1 2 3 4 5 6 7 8

12 Torq R5 R5 R5 R R R5 R R R R R R R R R R R R
ue 151 152 153 5 5 156 5 5 5 5 5 5 5 5 5 5 5 5
Load 1 1 1 1 1 1 1 1 1 1 1 1 1 1
5 5 5 5 5 6 6 6 6 6 6 6 6 6
4 5 7 8 9 0 1 2 3 4 5 6 7 8

13 Torq R5 R5 R5 R R R5 R R R R R R R R R R R R
ue 171 172 173 5 5 176 5 5 5 5 5 5 5 5 5 5 5 5
Limit 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Value 7 7 7 7 7 8 8 8 8 8 8 8 8 8
4 5 7 8 9 0 1 2 3 4 5 6 7 8

Axis Spindle others

PLC Interface Integration-Axis & Spindle – 158

 机床产品/Machine Tool Products
–
PLC Interface.

2.4 Command
Function\Spindle S1 S2 S3 S4 S5 S6 S7 S8 S9 S10
ID

1 Spindle PLC R580 R580 R580 R580. R580 R580 R580 R580. R580 R580
Control Mode .01 .02 .03 04 .05 .06 .07 08 .09 .10

2 Switch to C Axis C63 R581 R581 R581. R581 R581 R581 R581. R581 R581
Control Mode .02 .03 04 .05 .06 .07 08 .09 .10

3 Spindle Rotating C64 R583 R583 R583. R583 R583 R583 R583. R583 R583
CW .02 .03 04 .05 .06 .07 08 .09 .10

4 Spindle Rotating C65 R584 R584 R584. R584 R584 R584 R584. R584 R584
CCW .02 .03 04 .05 .06 .07 08 .09 .10

5 Spindle JOG C60 R585 R585 R585. R585 R585 R585 R585. R585 R585
Mode .02 .03 04 .05 .06 .07 08 .09 .10

6 Spindle C61 R586 R586 R586. R586 R586 R586 R586. R586 R586
Orientation .02 .03 04 .05 .06 .07 08 .09 .10

7 Target State of Y- R631 R631 R631 R631. R631 R631 R631 R631. R631 R631
D Winding .01 .02 .03 04 .05 .06 .07 08 .09 .10

2.5 Status
Function\S S1 S2 S3 S4 S5 S6 S7 S8 S9 S10
pindle ID

1 Switched to R582.01 R582. R582. R582. R582. R582. R582. R582. R582. R582.
C Axis / S63 02 03 04 05 06 07 08 09 10
Control
Mode

2 Spindle R587.01 R587. R587. R587. R587. R587. R587. R587. R587. R587.
Orientation / S61 02 03 04 05 06 07 08 09 10
Completed

PLC Interface Integration-Axis & Spindle – 159

 机床产品/Machine Tool Products
–
PLC Interface.

Function\S S1 S2 S3 S4 S5 S6 S7 S8 S9 S10
pindle ID

3 Rigid R588.01 R588. R588. R588. R588. R588. R588. R588. R588. R588.
Tapping / S04 02 03 04 05 06 07 08 09 10
Mode

4 Spindle R602.01 R602. R602. R602. R602. R602. R602. R602. R602. R602.
Request 02 03 04 05 06 07 08 09 10
Mode of Y-D
Winding

5 Spindle S64 R607. R607. R607. R607. R607. R607. R607. R607. R607.
Speed 02 03 04 05 06 07 08 09 10
Arrival for
Cutting

6 Spindle S59 R607. R607. R607. R607. R607. R607. R607. R607. R607.
Speed 12 13 14 15 16 17 18 19 20
Arrival for
Threading

7 Status of Y- R632.01 R632. R632. R632. R632. R632. R632. R632. R632. R632.
D Winding 02 03 04 05 06 07 08 09 10

2.6 Value
Function\Spind S1 S2 S3 S4 S5 S6 S7 S8 S9 S10
le ID

1 Spindle R761 R762 R763 R764 R765 R766 R767 R768 R769 R770
Machine （
Position R35）

2 Spindle Speed R771 R772 R773 R774 R775 R776 R777 R778 R779 R780
Feedback （
R36）

3 Spindle Gear R24 R782 R783 R784 R785 R786 R787 R788 R789 R790
Selection

4 Spindle Speed R851 R852 R853 R854 R855 R856 R857 R858 R859 R860
Override

PLC Interface Integration-Axis & Spindle – 160

 机床产品/Machine Tool Products
–
PLC Interface.

Function\Spind S1 S2 S3 S4 S5 S6 S7 S8 S9 S10
le ID

5 Spindle R871 R872 R873 R874 R875 R876 R877 R878 R879 R930
Effective Speed
Command

6 Spindle Speed R941 R942 R943 R944 R945 R946 R947 R948 R949 R950
Command for
PLC Control
Mode

7 Spindle Torque R5141 R514 R514 R514 R514 R514 R514 R514 R514 R515
Load 2 3 4 5 6 7 8 9 0

Axis Spindle others

2.7 Command
Function\Group 1 2 3 4

1 Axis Coupling Request C46 R614.02 R614.03 R614.04

2 Axis Exchange Request C133 C134 C135 C136

2.8 Status
Function\Group 1 2 3 4

1 Spindle Synchronization S62 S72 S73 NA

Finish

2 Axis Exchange Status S133 S134 S135 S136

3 Axis Coupling Status R609.01 R609.02 R609.03 R609.04

4 Spindle CSS Mode R628.01 R628.02 R628.03 R628.04

PLC Interface Integration-Axis & Spindle – 161

 机床产品/Machine Tool Products
–
PLC Interface.

2.9 Value
Function\Group 1 2 3 4

1 Effective Spindle Selection R791 R792 R793 R794

2 Spindle Max. Cutting Speed R5021 R5022 R5023 R5024

PLC Interface Integration-Axis & Spindle – 162