Warranty

To receive after-sales service, have the following

ready when you contact our branches
1. Name of the product
2. Model number of the product
3. The area of problem
4. Phone number and address at which you can be contacted. VIDEO DOORPHONE KVM-524RG Operating Installation Manual

Clear & Bright Picture at Low Light

Thank you very much
■ CCIR/EIA: Images Recordable for purchasing KOCOM
Warranty Card ■ 4″Flat Monitor / 4 Wired In Polarity video doorphone.
please read this manual
■ Easy Installation thoroughly to ensure
PRODUCT ■ Wide view angle correct usage, before
■ AC 110V or 220V (50Hz / 60Hz) Transformer type operating
MODEL
DATE PURCHASED ■ Door release function
■ Additional 1 Monitor + 1 Camera + 2 Doorphone available
WARRANTY PERIOD ■ I
AGENCY ADDRESS

◉ KOCOM Warranties the original purchaser of this product

as follows.
1) This product is produced under strict quality control and inspection procedures.
PLAY

AUTO
REC

2) If this product breaks down during proper use as a result of product defect, KOCOM REC

TIMES

will repair it within one year from date of purchase free of charge.
3) The following cases will be subject to charge, even during warranty period:
a. Breakdown during transport, or through careless treatment, by consumer. Camera
4-wires In
b. Breakdown cause by unauthorized repair, or system modification. polarity KC-D20
c. Breakdown caused by natural disaster or power disorder.
or
Monitor
KVM-524RG

"CAUTION: IT HAS POSSIBILITY TO HAPPEN ※Option

INOPERABLE, AS THIS PRODUCT Camera
EXPOSED TO ELECTRON WAVE" KC-B61

This manual is based on the date as shown in the right and specifications
are subject to change without notice for quality improvement. KVM-524RG 04.08
 Warnings
Cautions for Safety Warnings for disposal
For safe use, please stick to the following cautions. � Do not throw used-up battery into fire places, which may cause fire and explosion.

�Read this cautions carefully and keep it within easy reach of you. Cautions
�For right installation, read this cautions thoroughly. Please install the product according to its specifications.
�This Cautions for Safety may include items that are not contained in specifications of the product that consumer Cautions for installation
purchases. � The relevant law obliges users to have a qualified electrician carry out wiring work for power supply. Work by disqualified
�Reading this cautions, use the product in a right manner. For further information, please contact our A/S center. persons may cause fire and electric shock.
� Wiring work for communication cables needs techniques and experiences. For this type of wiring work, please consult to your
About Symbol local sales agent.
A variety of symbols are used in this Cautions for Safety and your products to guide you to use products in a right � According to the standard for electric work and other relevant regulations, install communication cables at the place away
and safe manner and to prevent possible risks for users and other persons and damages to their property. The meaning from power cables. The failure to install cables separately may cause fire, electric shock and communication troubles.
of each symbol is as follows. After fully aware of meaning of each symbol, read the following cautions. � Do not install the product on rolling table or sloping place.
Dropping or falling may cause damage on your product.
This symbol means that wrong handling or ignorance of matters that this symbol indicates � In installation, avoid the place exposed to tremor or shocks, which may cause damages on your product.
Warnings may cause serious injury or even death of user. � Even if your product is waterproof, do not install it slanted place of water leakage, which may cause a short circuit.
� For the product of wall-mounting type with fixing pegs, keep it safely.
This symbol means that wrong handling or ignorance of matters that this symbol indicates Fixing pegs may cause injury of user.
may cause serious injury or property damage of user.
Cautions
� Install the product of wall-mounting type carefully not to drop from the wall. Dropping due to earthquake or tremors may
cause injury of user.
This symbol means the matter that user should not do at nay event. � When installing the product on the wall, consider the thickness and material of the wall.
Dropping in use may cause injury of user.
This symbol means that user should follow the instructions.

Cautions for Use

� Do not put heavy thing on the product. Dropping or falling due to heavy things on it may cause injury of user.
Symbols on Drawing
This symbol means that contents (high voltage, electric shock, warnings, etc.) to which user Cautions for Repairs and Maintenance
should pay attention are included. � Clean the dust inside the product regularly. Failure to clean the dust for long time may cause fire. For inspection and cleaning
of the inside of product, please contact your local sales agent.
This symbols means that a certain action is not permitted. Specific points not permitted are � When putting your hands into the inside of equipment, be sure that plug is already detached form an outlet or circuit-breaker is
depicted around this symbol (for example, in the left drawing, disassembly is not permitted.). turned off.
� Be careful not to expose the product to benzene, thinner or hot water.
This symbol means instructions or is used to force user to do a certain action. Specific � Do not expose detergent directly to the product in a way of spaying, etc.
instructions are depicted on the drawing � Moving equipment, be sure that the plug is detached from an outlet.
(for example, the left drawing instructs user to detach power plug from an outlet). � For equipment whose cables are connected to terminals, please contact your local sales agent or qualified electrician.
� When replacing old fuse with new one, do not directly touch it with bare hands.
Use insulated tools or contact A/S center.
 Warnings Warnings
Cautions for Use Cautions for Use
�Do not install the product at bathroom or at the place near a washing machine, or at other humid places. It may cause fire or �This product is only for home. Do not the product for industrial or military use.
electric shock. � Do not handle the equipment with wet hand, which may cause electric shock.
�Do not install the product at the place near a dresser, humidifier or heater. Also avoid the place exposed to spark, heat or � Do not place wet or metallic materials on equipment. Water leakage or intrusion of metallic materials may cause fire and
humidity. All of them may cause fire and electric shock. electric shock.
�Do not install the product at the place exposed to dust, metals and harmful gas such as hydrogen sulfide gas, all of which � Do not block the ventilating opening of equipment or put alien substances into it, which may cause fire and electric shock.
may cause fire and electric shock. � Do not use battery that is not designated or mix new battery with old ones. Insert batteries to fit their polarity. Explosion or
�Do not install the product at the place exposed to water and chemicals. This may cause fire and electric shock. leakage of battery may cause fire and injury of user.
� Do not scratch, break or arbitrarily process power cable, which may cause fire and electric shock. Putting a heavy thing on a � When visitor's image or voice is not displayed on screen or not sounded from speaker, please check his/her identity before
cable, heating it or pulling it may cause impairment on it. opening the door and contact our A/S center.
�Do not place power cable at the place near heating equipment. It may cause damage of cable's clothing material, which �Do not use equipment when lighting is expected or strokes. It may cause fire and electric shock.
result in fire ad electric shock. When detaching plug from an outlet, do not pull power cable.
�Damages on power cable may cause fire and electric shock. When detaching plug from an outlet, please hold the plug � Do not open rear cover, cabinet and cover of equipment. It may cause electric shock.
tightly.
�Do not detach plug from an outlet with wet hand. I may cause electric shock. � Do not modify power cable or pull it with excessive strength, which may cause fire and electric shock.
�When using the existing wiring, be sure of the suitability of it to the product and install the product. Failure to this caution �Do not modify equipment. It may cause fire and electric shock.
may cause fire. �Call signal may cause damage on user's hearing ability.
�When moving equipment, be sure that plug is detached from an outlet and communication cable is disconnected. Damage
on cables may cause fire. Cautions for Abnormality
�Voltage other than prescribed rated voltage is not permitted, which cause fire and electric shock. � When power cable is broken (exposure of core or short-circuit), do not fail to replace broken cable with new one. Failure to
�Do not use power terminal of product's main body in other equipment than prescribed ones. It may cause fire and short- replace broken power cable may cause fire and electric shock.
circuit. �When detecting any abnormalities in equipment (communication is not available, images do not be displayed on screen, calling
�In wiring work, use the designated wiring materials. is not available, or abnormal sound is heard), immediately detach plug from an outlet, or turn off circuit breaker or detach
Wiring work using other materials than designated ones may cause fire. batteries from equipment (in case that equipment has no plug) before requesting repairs to sales agent or A/S center. Keeping
� The equipment without waterproof marking shall not be installed at the place water leaks. It may cause electric shock and connection to power supply may cause fire and electric shock.
short circuit. �When alien substances go into equipment, immediately detach plug from an outlet, or turn off circuit breaker or detach batteries
�When working, be sure that power is disconnected. Failure to disconnect power may cause electric shock. from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center.
� Be sure that the power cable is connected and earths according to designated method. Failure to connection and earth may � In the case of smoke or smell of unknown origin from equipment, keeping use it may cause fire and electric shock. Detach
cause fire. plug from an outlet, or turn off circuit breaker or detach batteries from equipment (in case that equipment has no plug) and be
�Do not connect power to other terminals than designated ones. sure to check no more smoke or smell from equipment before requesting repair to sales agent or A/S center. Since personal
�It may cause fire and electric shock. repairing work by user may serious accidents. In any case, do not repair equipment with your own hand.
� When building a system with the product, do not connect the product other equipment than designated one. It may cause �When dropping equipment or breaking its cabinet, detach plug from an outlet, or turn off circuit breaker or detach batteries
fire. from equipment (in case that equipment has no plug) before requesting repair to sales agent or A/S center. Keeping use
�When installing A/C switch, do work after removing the substance that may cause short circuit or electric shock. equipment may cause fire and electric shock.
�Before installing or providing A/S service, be sure that the power is disconnected. � Avoid direct exposure to sunlight and store equipment at the place free from dust and high temperature as you can. High
temperature of equipment may cause fire and electric shock.
 Safety Instructions, Warnings, and Cautions of Each System

- This equipment is electronically precision equipment, so do not arbitrarily disassemble it.

- In installation of the product, do not fail to follow the specifications (specifications offered by KOCOM).
- Do not touch the product with alien materials (for example, sticker, magnet, opener, metal chopstick, etc.)
or insert them into the product (it may cause reduction of the product's durability and harmful results to user as well).
- In the rainy season, water is likely to penetrate into the product along the wiring. Thus, U-type finishing is recommended
as a desirable method of end part finishing.

Video Phone
- In assembling the product, be careful that wall-mounting pegs should not contact with wirings.
- In connection of cables, strip its insulation off as much as necessary (Excessive stripping off its insulation may cause short circuit).
- Be careful that signal cables should not be wired with A/C wiring (it may cause poor display quality).
- Do not drop handset (its damage or short-circuit due to drop may make communication impossible).
- When connecting wires to terminals, use standard screwdriver (otherwise, screws may loosen, which will result in disconnection of wiring).
- Do not clean CRT screen with wet towel or cloth. When water penetrates into the product, it may cause short-circuit.
Do not fail to clean it with dry towel or soft cloth.
- Do not install camera at the place where water penetrates or leaks. Penetration or leakage of water may cause electric shock or short circuit.

4-Line Related Products

- In wiring work, be careful that wirings should keep away from the wall-mounting pegs or other furniture at regular interval. Contact of wiring with
wall-mounting pegs, etc. may cause short-circuit, electric shock and fire (it is applied to all products with wall-mounting pegs).
- Use the prescribed standard wirings. Non-standardized wirings may give adverse effects on operation of product
(it is applied to both video phone and CCTV).
 Precautions for Operation Component

PLAY

AUTO
REC

REC

PLAY
●Monitor & Camera ●Camera Accessories
TIMES AUT
REC O
PLAY

REC AUTO
REC

TIME
S

REC

TIMES

PLAY

AUTO
REC

REC
�finishing rubber
TIMES

�Screw for fixing camera

main body supporter
Keep away from humidifier and Do not drop monitor or door Keep away from devices 4 x 10mm
stove. High temperature and camera, and avoid strong generating strong magnetic field �Main body
humidity can cause breakdown. impact. (TV, Speaker, etc.) (Picture can supporter �Screws for fixing camera
be disturbed or blurred and 4 x 16mm
breakdown can result)
●Monitor Accessories ●KDP-602G Connector Wire for
Extention
PLAY

AUTO
REC
4 x 150mm (5264-04TYPE)
PLAY
REC

TIMES
�Screws for
AUTO
REC

REC

TIMES
REC
PLAY

AUTO
REC
fixing
4 x 30mm
TIMES

T
B E N Z E NEHIN N E R

�Wall hanger panel

※Wall hanger panel is

When cleaning, never use wet Keep picture clear by cleaning As this device consists of packed in the Monitor
hands, volatile benzene or paint camera window frequently with electronic precision
thinner. soft cloths. components, and high voltage Specifications
is generated internally, do not
attempt to disassemble.
Power source AC 110V - 120V ~ (50Hz / 60Hz) or
AC 220V - 230V ~ (50Hz / 60Hz)
Power consumption Max: 19W, Stand by : 4W
Installation Precautions
MONITOR Ambient temperature 0℃~+50℃
� Monitor and camera must be installed away from direct (KVM-524RG) Braun tube 4 inch Flat Tube (B/W)
light and counter light. Communication system Duplex handset conversation
� Camera must be installed at a place free from rain. Call signal sound Electric chime & beep sound
� Standard height of monitor must be 1,450mm~1,500mm Output Impedance Picture : 75ohm, Voice : 600ohm
from ground, centered around brawn tube. Wiring 4 Wired in Polarity (VCC / GND/VOICE / PICTURE )
� Camera should be installed on the wall in which cement Max Wiring Distance �0.65 Single Cable/50m, 5C-2V Coaxial Cable/100m
is completely dry. Dimension 210(W)×222(H)×53(D)mm
� If installed during winter season at temperature below Power source DC12V± 1V(power from Monitor)
-5� , condensation might be generated inside monitor and Power consumption Max: 2.5W
camera due to temperature difference between indoors Assurance temperature -10℃~50℃
and outdoors. To prevent breakdown due to such Scanning frequency Horizontal: 15.734KHz,15.625KHz
condensation, connection should be made in 2 hours or Stop up P.V.C. pipe using
CAMERA Vertical: 50Hz (CCIR)/60Hz (EIA)
more after installation. adiabatic substances, to (KC-D20) Lens F:2.0, f=3.0mm
prevent air circulation
� Do not install monitor and camera in locations subject to ※ Stopping up pipe as above minimizes Min. Illumination 0.1Lux (LED ON)
direct heating as harmful gases may subsequently be temperature difference between indoors Dimension 96(W)×127(H)×32(D)mm
and outdoors, and also eliminates
emitted in significant amounts. moisture and condensation on Illumination Infra-red LED
door camera window. Angle of picture Diagonal 120。 (KC-B61), 90。(KC-D20)
Color of KC-D20 Black or Silver
 Name of each part Monitor Installation
■ KVM-524RG Monitor �Handset
Basic Installation method of Monitor When system is attached to 1 rectangular switch box
To communicate with Screw 1 Rectangular Screw
Wall
Manual/Auto recording � door camera.
switch box

Lamp � PLAY

� 4 inch screen
AUTO
REC

PLAY

Play Button�
REC
AUTO
REC

TIMES

REC

PLAY

AUTO To identify visitor TIMES

Can confirm recording� REC

images in order�
REC

TIMES
� Button Wall hanger panel
To call and commu- Wall hanger
for fixing Monitor panel for
Auto-Rec. Button � nicate with other fixing Monitor
s�
To record all visitor’ monitor or doorphone

image automatically� � Button

when you absent� To confirm visitor
Mamual Rec. Button � without holding
Can record visitor� the handset Center of monitor

on purpose�
� Button � Standard height monitor
Time mode Button� Door opens when this Bottom of
To select the month,� button is pressed. � Standard height of monitor is ranged 1,450 ~ 1,500 1 Rectangular

time..etc.�
� Power Lamp Available only for from bottom to the center of monitor screen. switch box

To check power the door equipped � For installation, avoid the places where there is any
Time set Button � ON/OFF status with door opener. excessive humidity,magnetic force, dangerous
To set up the� chemicals, direct ray of sun, and any places near a
month, time..etc�
� Brightness Control heater which can cause break down.
(unit:mm)
Knob
To control brightness
Call Signal � of monitor screen
Volume Control Knob� Door camera Installation
To control calling� � Contrast Control Knob
signal volume.� To control contrast of
monitor screen.
� KC-D20 Surface-mounting Door Camera Installation

Straight Ahead Installation

Bottom base of
One hall Box
■ KC-D20 Metal Pinhole Camera & KC-B61 Camera Surface mount

Flush mount

� Speaker � C-Mic
When visitor calls, the To communicate
voice from monitor comes with Monitor
out of the speaker.
� Speaker
� Camera Lens When visitor calls,
Clear picture quality realized the voice from monitor (unit:mm)
by adopting 1/3" CCD comes out of the speaker.
� Call Button � Power Lamp After attach the body supporter with 2 screws,
By pressing the button, the To check power put the Door Camera into the grooves of body supporter,
related house will be called. ON/OFF status and then fix it with 2 screws and stick the finishing materials.

� C-Mic � Standard Height of Door Camera

To communicate
with Monitor � Standard height of the door camera is 1,400mm � 1,450mm from the bottom of one camera to the floor.
� In case that the height of Door camera exceeds the range of min. 1,250mm�1,550mm, it is impossible to control
the screen picture with only the lens angle, and therefore, be careful of the height of camera installation.
 How to operate (Instruction for operating) � Checking out door side - Don’t need to hold handset
� Identifying and talking to visitors 1. If press button on the monitor, screen is turned on
automatically. And, you can check out door side.
PLAY PLAY

AUTO AUTO
REC REC

REC

TIMES
REC

TIMES 2. After checking, screen is turned off as pressing button again.

PLAY

3. After internal call is made, the monitoring is not availalle for 60 sec.
AUTO
REC

REC

TIMES

1.Call signal rings from the monitor, while screen is 4. Monitoring when 2 cameras are connected.
turned on and visitor is appeared automatically.
-Using hanset
When visitor presses the call If the handset is picked up, press button shortly in order to
button of door camera. change the camera.
-Without using handset
2-1 Hold handset and identify visitor. Camera 1selection : press button shortly
Then, communicate with visitor. And,unless you replace handset within 3minutes, the Camera 2selection : press button a little longer, till screen is on.
PLAY

AUTO
REC
monitor screen is turned off automatically.
2-2 When the handset is held on and the call is made from the camera, press button
�
REC

TIMES

on the monitor. then communicate with visitor.

Identifying visitors
2-3 While communicating with camera, if the internal call is made from the extended
monitor or doorphone, the beep signal sounds in 5 sec. and disconnected with the camera PLAY PLAY
1. If press call button on the door camera, the screen is turned
AUTO AUTO

automatically Then you can communicate with extended monitor or doorphone after
REC

on automatically. And, you can check out door side.

REC

REC REC

TIMES TIMES

pressing button on the monitor. 2. At this time, you can easily identify visitors without lifting
handset. ( After 60sec., Monitor screen is turned off
automatically)
PLAY

AUTO
REC
3.After communication replace handset. However, if conversation continue more than
REC

TIMES
3minutes, monitor screen is turned off automatically. And if you want to communicate
more time, press button again.
� Opening door automatically (Regardless of handset status)

PLAY

AUTO
REC
PLAY

AUTO
REC
1. For this purpose, automatic AC doorlock should be first
REC REC

TIMES TIMES

installed on the door and then connected with video doorphone

� Manual Record & Auto Record
REC
1. Manual Record : Please choose monitor image as pushing“Camera 1” or ‘Camera 2’ button. 2. After communication with visitor, press button,
And then the image will be recorded when you push ‘REC’ button. and the door is automatically opened
AUTO
REC
2. Auto Record : If you push ‘AUTO-REC’ button, the green LED lamp will turn on and the
images will be recorded with blinking red color LED automatically when push camera’s call button.
(Auto-recording. is not available within 30 seconds after recorded)
� Internal call and intercom function
� Play Recorded Image
Hold on handset and press button on the monitor.
If you push ‘Play’ button , you can find one cut image with time in order from the latest images. PLAY

AUTO
REC

PLAY REC

TIMES
Then the call signal sounds from the extended monitor or doorphone.
It’s not available with auto re-play for all images by one touch.
※In the case of full recorded images, it will be removed from the oldest image in order.
And if it is answered from the extended monitor or doorphone you can
communicate.
� Time Setting In case the handset of the extended monitor is held on, and button
1. Turn on the monitor’s screen as pushing camera1 or camera 2 button on the extended monitor is pressed, you can communicate.
TIMES
2. Press “Time Mode” (for 2 seconds), then appears “Time Mode” at the center of monitor’s screen
and “Minute” is on the blink.
During internal communication, if the call is made from the camera, the beep signal sounds in a sec. and the
call signal from the camera sounds.
3. Change the number as pushing “Time set”button & Select wanted number with “Time Mode”
At same time the monitor is disconnected automatically with extended monitor or doorphone
button. As like above method, set time & date continuously (minutes -> time -> date -> month ->year). Then if you press button on the monitor, you can talk with visitor
4.‘REC’ button :Down-Count , “ Time set” button:Up -Count

� Opening front door automatically When additional monitor and door phone are connected to the monitor.
※ Caution as doorphone has no security function, the conversation between 2 monitors
After communication with visitor, press door key button. Then, the door is opened automatically.
can be heard from the extended doorphone without notice.
 Video Doorphone Wiring Diagram 1 Video Doorphone Wiring Diagram 2

In case of UPT cable wiring, please refer to the wiring and this wiring is recommended.
please avoid wiring R(audio)and W(video) in a twisted cable.

● In case, 2 camera are used, terminal GND(Y) of each camera should be connected
to the terminal Y1 of the first monitor. AC or DC

● For the dotted line (A) in TIV 1.6 must be used

● For the dotted line in TIV 0.65must be (B) used. (Max. cable distance 50m)

Transmission 4-wired Wiring

TIV0.5� : Max. 20m
Cable Distance TIV0.6� : Max. 30m
TIV0.65�: Max. 50m
Coaxial cable : Max. 100m

Transmission 4-wired Wiring

● For the dotted line (A) in TIV 1.6 must be used
Caution for wiring TIV0.5� : Max. 20m
● For the dotted line in TIV 0.65must be (B) used.
(Max. cable distance 50m) Cable Distance TIV0.6� : Max. 30m
�Available video doorphone wiring with TIV O.65mm is less than 50m in length.
TIV0.65�: Max. 50m
�Connecting wiring between monitor and door camera should not be installed Coaxial cable : Max. 100m
near other electrical cable, nor be horizontal.
(In such case, clear picture can not be expected due to interruption by electrical noise)