Scribd
Upload
18 views

Fitting Format Report EDITED

This document is a report template for a Mechanical Workshop Practice 1 fitting session. It provides guidelines for students to document their workshop work, including sections for introduction, safety precautions, equipment used, procedures followed, discussion of results, and conclusions. The template specifies what information should be included in each section, such as listing safety measures, describing tools and machinery, outlining the step-by-step process, addressing any errors or findings, and determining if objectives were achieved. Pictures or diagrams can also be added where relevant.

Uploaded by

Harith Danial
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
18 views

Fitting Format Report EDITED

This document is a report template for a Mechanical Workshop Practice 1 fitting session. It provides guidelines for students to document their workshop work, including sections for introduction, safety precautions, equipment used, procedures followed, discussion of results, and conclusions. The template specifies what information should be included in each section, such as listing safety measures, describing tools and machinery, outlining the step-by-step process, addressing any errors or findings, and determining if objectives were achieved. Pictures or diagrams can also be added where relevant.

Uploaded by

Harith Danial
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 11

MECHANICAL ENGINEERING DEPARTMENT

DJJ10022

MECHANICAL WORKSHOP PRACTICE 1

(FITTING)

NAME HARITH DANIAL BIN SHARIZAL SHAN

MATRIC 10DKM23F1076 CLASS DKM1B


NO.
GROUP SESSION 1 : 2023/2024
LECTURER
REPORT 4 3 2 1 points

(CLO 1) weightage

A. Introduction 2 _____/
8
B. Safety 3 _____/
12
C. Equipment 5 _____/
20
Total _____/
40
REPORT D. Procedures 5 ____/
20
(CLO 2) E. Discussion 3
____/12
F. Conclusion 2 ____/8

Tot _____/
al 40

Contents of Report
1. Introduction
▪ Title
▪ Objective stated ( depends on the practical task)
▪ Theory explained clearly related to the workshop respectively

2. Safety Precaution
▪ Detail information about safety precaution taken in workshop which related to the
Occupational Safety and Health Administration (OSHA).

3. Equipment
▪ Picture / figure any related equipment and measurement instruments used
▪ Information and function for each equipment and measurement instruments
➢ Measurement instruments that related to the task (E.g; steel ruler, Vernier caliper, centre
gauge, L square)

4. Procedures
▪ A clear information of how the procedure was performed
▪ Explain the process of the task from the beginning until to the last process include the
relevant figure of the procedure

5. Discussion
▪ Discuss the finished product gained after the task is completed ➢ Attach the
picture of your project.
▪ List down the error from the task and explain how to overcome the error. ▪
Any related information can be discussed

6. Conclusion
▪ Make a conclusion based on the respective project and workshops
▪ Conclude the stated objectives whether achieved or not Any related information
can be conclude.

1.0 Introduction
………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

2.0 Safety Precautions

• ………………………………………………………………………………………………………

………………………………………………………………………………………………………

• ………………………………………………………………………………………………………

………………………………………………………………………………………………………

• ………………………………………………………………………………………………………

………………………………………………………………………………………………………

• ………………………………………………………………………………………………………

………………………………………………………………………………………………………

• ………………………………………………………………………………………………………

………………………………………………………………………………………………………

• ………………………………………………………………………………………………………

………………………………………………………………………………………………………

3.0 Apparatus / Equipment A)


Measurement Tools
No. Figure Name Function
1

5
6

B) Marking Tools

No. Figure Name Function


1

C) Clipping Tools
No. Figure Name Function
1

D) Cutting Tools
No. Figure Name Function
1

E) Rotating Tools
No. Figure Name Function
1

4.0 Procedures

Figure Description

1. File the surface of the work


piece until it is exactly 90

2.
3.

4.

5.
6.

7.

8.
5.0 Discussion

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

……………………………………………………………………………………………………………….

6.0 Conclusion

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………
………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

………………………………………………………………………………………………………………

You might also like