Scribd
Upload
21 views

Temporary Footingfor Rectangular Tank

The document summarizes the design of a temporary tank footing based on ACI 318-05 standards. It provides the input data for the design including the tank size, base plate edge size, concrete strength, rebar yield stress, dead and live loads. It then summarizes the design including the required footing width and length, and checks that the design is adequate for soil bearing capacity, flexure, flexure shear, and punching shear. The analysis found the design to be satisfactory for all checks.

Uploaded by

Abdul Wahab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
21 views

Temporary Footingfor Rectangular Tank

The document summarizes the design of a temporary tank footing based on ACI 318-05 standards. It provides the input data for the design including the tank size, base plate edge size, concrete strength, rebar yield stress, dead and live loads. It then summarizes the design including the required footing width and length, and checks that the design is adequate for soil bearing capacity, flexure, flexure shear, and punching shear. The analysis found the design to be satisfactory for all checks.

Uploaded by

Abdul Wahab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

Daniel PROJECT : PAGE :

CLIENT : DESIGN BY :
Tian Li JOB NO. : DATE : REVIEW BY :
Temporary Tank Footing Design Based on ACI 318-05

INPUT DATA DESIGN SUMMARY


TANK SIZE c1 = 40 ft FOOTING WIDTH B = 22.00 ft
c2 = 20 ft FOOTING LENGTH L = 42.00 ft
BASE PLATE EDGE SIZE b1 = 40.5 ft FOOTING EDGE THICKNESS T = 10 in
b2 = 20.5 ft
FOOTING CONCRETE STRENGTH fc' = 2 ksi
REBAR YIELD STRESS fy = 60 ksi
TOTAL DEAD LOAD PDL = 23 kips
LIVE LOAD PLL = 1450 kips
SURCHARGE qs = 0.1 ksf
SOIL WEIGHT ws = 0.11 pcf
FOOTING EMBEDMENT DEPTH Df = 0.50 ft
FOOTING EDGE THICKNESS T = 10 in
ALLOW SOIL PRESSURE Qa = 2 ksf
FOOTING WIDTH B = 22 ft
FOOTING LENGTH L = 42 ft

THE FOOTING DESIGN IS ADEQUATE.

ANALYSIS
DESIGN LOADS (ACI 318-05 SEC.9.2.1)
ASD: DL + LL P = 1582 kips
SD: 1.2 DL + 1.6 LL Pu = 2189 kips

CHECK SOIL BEARING CAPACITY (ACI 318-05 SEC.15.2.2)


ASD
P
q MAX  = 1.71 ksf, < Qa [Satisfactory]
BL
DESIGN FOR FLEXURE (ACI 318-05 SEC.22.5.1)


 M n  MIN 5 f 'c S , 0.85 f 'cS  = 45.09 ft-kips

where f = 0.55 (ACI 318-05, Section 9.3.5 )


S = elastic section modulus of section = 4400 in3

 0.5L 0.25b10.25c1
2
P u ,max
Mu  = 19.95 ft-kips < fMn [Satisfactory]
2L
CHECK FLEXURE SHEAR (ACI 318-05 SEC.22.5.4)

4
 V n   f 'c BT = 86.58 kips
3
where f = 0.55 (ACI 318-05, Section 9.3.5 )

P u ,ma x
V u   0.5 L  0.25b1  0.25c 1  T  = 2.17 kips < fVn [Satisfactory]
L
CHECK PUNCHING SHEAR (ACI 318-05 SEC.22.5.4)

 4 8  
 V n  MIN    , 2.66   f c  c1  c 2  b1  b2  4T  T
'
= 976.18 kips
 3 3 c  
where f = 0.55 (ACI 318-05, Section 9.3.5 )
bc = ratio of long side to short side of concentrated load = 1.99

 1  b1  c 1  b  c 
V u  P u ,ma x 1    T   2 2  T  = 136.98 ft-kips < fVn [Satisfactory]
 BL  2   2 

You might also like