Scribd
Upload
27 views2 pages

Sheet 3

This document contains 7 problems related to designing compensators for automatic control systems. The problems involve designing compensators to achieve specific closed-loop pole locations and responses, including setting the static velocity error constant and limiting overshoot and settling time. Compensators include lead, lag, and lag-lead configurations. Students are instructed to use MATLAB to plot unit-step and unit-ramp responses for some of the designed systems. The problems are from a course on automatic control systems in the Electrical Engineering department at Aswan University.

Uploaded by

bipico9217
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
27 views2 pages

Sheet 3

This document contains 7 problems related to designing compensators for automatic control systems. The problems involve designing compensators to achieve specific closed-loop pole locations and responses, including setting the static velocity error constant and limiting overshoot and settling time. Compensators include lead, lag, and lag-lead configurations. Students are instructed to use MATLAB to plot unit-step and unit-ramp responses for some of the designed systems. The problems are from a course on automatic control systems in the Electrical Engineering department at Aswan University.

Uploaded by

bipico9217
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Aswan University

Fourth Year
Faculty of Engineering
Automatic Control (II) Course
Electrical Engineering Department
First Semester
Computers and Systems Section
Sheet No. 3

Sheet No. 3

1- Design a lead compensator such that the dominant closed-loop poles are located at 𝑠 = −2 ±
𝑗2√3. Plot the unit-step response curve of the designed curve with MATLAB.
C(s)
R(s) 5
+ Gc (s)
- s ( 0 . 5 s  1)

2- Design a compensator such that the unit-step response curve will exhibit maximum overshoot of
25% or less and settling time of 5 sec or less.

C(s)
R(s) 1
+ Gc (s)
- s (s  4)
2

3- Design a compensator such that the dominant closed-loop poles are located at 𝑠 = −2 ± 𝑗2√3 and
static velocity error constant Kv is 50 sec-1. Plot the unit-step response curve of the designed curve
with MATLAB.

C(s)
R(s) 10
+ Gc (s)
- s(s  2)(s  5)

4- Design a compensator such that the dominant closed-loop poles are located at 𝑠 = −2 ± 𝑗2√3 and
the static velocity error constant Kv is equal to 80 sec-1.

C(s)
R(s) 10
+ Gc (s)
- s ( s  2)( s  8)

5- Design a compensator such that the unit-step response curve will exhibit maximum overshoot of 30
% or less and settling time of 3 sec or less.

2s 1
R(s) C(s)
+ Gc (s)
- s(s 1)(s  2)

With my best wishes Dr. Mountasser M. Mohamed


Aswan University
Fourth Year
Faculty of Engineering
Automatic Control (II) Course
Electrical Engineering Department
First Semester
Computers and Systems Section
Sheet No. 3

6- Design a lag compensator Gc(s) such that the static velocity error constant Kv is 50 sec-1 without
appreciably changing the location of the original closed-loop poles, which are at 𝑠 = −2 ± 𝑗√6.
Plot the compensated system for a unit step input as well as unit ramp input (Use MATLAB).

R(s) C(s)
10
+ Gc (s)
- s(s  4)

7- Design a lag-lead compensator such that the static velocity error constant Kv is 50 sec-1 and the
damping ratio (ζ) of the dominant closed-loop poles is 0.5. (Choose the zero of the lead portion of
the lag-lead compensator to cancel the pole at s = -1 of the plant.) Determine all closed-loop poles
of the compensated system.

C(s)
R(s) 1
+ Gc (s)
- s(s  1)(s  5)

With my best wishes Dr. Mountasser M. Mohamed

You might also like