CMP CMP PRODUCTS CABLE GLAND CATALOGUE

CMP EXPLOSIVE ATMOSPHERES PRODUCTS

E1FX
TECHNICAL DATA
Design Specification BS 6121:Part 1:1989, IEC 62444, EN 62444
Mechanical Classifications* Impact = Level 8, Retention = Class B

E1FX Internationally Approved, Explosive Enclosure Protection IK10 to IEC 62262 (20 joules) Brass & Stainless Steel only

Atmosphere Cable Gland Electrical Classifications* Category B (Category A when used with braid, tape or pliable wire armour cables)
ATEX Certificate SIRA13ATEX1071X, SIRA13ATEX4077X
^ II 2G, II 1D, Ex d IIC Gb, Ex e IIC Gb, Ex ta IIIC Da,
For Braid & Steel Tape Armoured Cables Code of Protection
^ II 3G Ex nR IIC Gc, ^ IM2 Ex d I Mb, Ex e I Mb
Compliance Standards EN 60079-0,1,7,15,31
• Metal-to-metal armour clamping IECEx Certificate IECEx SIR 13.0026X, IECEx SIM 14.0007X
• Direct & remote installation Code of Protection Ex d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
• Displacement type flameproof inner seal Compliance Standards IEC 60079-0,1,7,15,31

• Controlled outer ‘load retention’ seal cCSAus Certificate 1310517

Ex d IIC; Ex e II; Ex nR II; Class I, Div 2, Groups A,B,C,D, Class II, Div 2 Groups E,F,G, Class III;
• Unique OSTG prevents overtightening Code of Protection
Encl Type 4X Class I, Zone 1, AEx e II / AEx nR II
CAN/CSA-C22.2 No 0,18,25,30,174,94, CAN/CSA-E60079-0,1,7,15
• Designed to prevent Coldflow Compliance Standards
ANSI/UL 514B Ed 5, ANSI/UL 50 Ed 11, ANSI/UL 2225 Ed 4, UL60079-0,1,7,15
EAC Certificate
• -60˚C to +130˚C TC RU C-GB.ГБ05.B00138
(Formerly GOST R, K & B)
• Class I Zone 1, 21 and Zone 2, 22 Class I Division 2 ABCD KCC Certificate 14-GA4BO-0257X
CCOE / PESO (India) Certificate P333688
• Globally marked, IECEx, ATEX & cCSAus
NEPSI Certificate GYJ13.1140X / GYJ13.1282X
• EMC tested
INMETRO Approval TÜV 12.0618X
RETIE Approval Number 03866
Marine Approvals LRS: 01/00172 (E3), DNV: E-13848, ABS: 14-LD234401A-4-PDA
Ingress Protection Rating IP66 as standard (IP67, IP68 available upon request)**
Deluge Protection Compliance DTS01:91 option available on request (white ferrule for identification purposes)
Cable Gland Material Brass, Electroless Nickel Plated Brass, Aluminium
Seal Material CMP SOLO LSF Halogen Free Thermoset Elastomer
Screened Flexible (EMC) Wire Braid (e.g. CY / SY), Pliable Wire Armour (PWA), Steel Tape
Cable Type Armour (STA), Wire Braid Armour (e.g. SWB), Aluminium Strip Armour (ASA), Armoured &
† Grooved Cone (X) is predominantly used for Wire Braid (e.g. GSWB, TCWB), Steel Tape Armour Jacketed
(STA, DSTA) and Aluminium Strip Armour (ASA) but is also suitable for Single Wire Armour (SWA),
Aluminium Wire Armour (AWA) and Pliable Wire Armour (PWA) if the range is outside that of the Armour Clamping Detachable Armour Cone & AnyWay Universal Clamping Ring
Stepped Cone (W).
Sealing Technique CMP Inner Displacement Seal & Unique CMP ‘LRS’ TM Outer Load Retention Seal
Note: Grooved Cone (X) dimensions shown in the Cable Gland Selection Table below are for a
double wire strand of braid armour cables. Tapes can also be doubled over. For cables that have only a Sealing Area(s) Cable Inner Bedding & Outer Cable Sheath
single layer of armour such as SWA the clamping range should be used as shown in the table below.
Note : * Mechanical & Electrical Classifications applied as per IEC 62444 & EN 62444
Note : ** Refer to page 7 or www.cmp-products.com for further information on Ingress Protection Ratings

Cable Gland Selection Table

Refer to illustration at the top of the page
Available Entry Threads “C” Cable Overall Armour
Across Combined Ordering
(Alternate Metric Thread Lengths Available) Bedding Cable Range † Across
Corners Reference Cable
Cable Diameter Diameter Grooved Flats “D” Protrusion
Standard Option “D” (*Brass Metric) Gland
Gland “A” “B” Cone (X) Length Shroud
Weight
Size Thread “F”
Thread Length Ordering (Kgs)
Metric NPT Length (NPT) NPT Min Max Min Max Min Max Max Max Size Type
(Metric) “E” Suffix
“E”
20s16 M20 15.0 1/2” 19.9 3/4” 3.1 8.6 6.1 13.1 0.3 1.0 24.0 26.4 72.5 20S16 E1FX 1RA PVC04 0.16
20S M20 15.0 1/2” 19.9 3/4” 6.1 11.6 9.5 15.9 0.3 1.0 24.0 26.4 70.0 20S E1FX 1RA PVC04 0.15
20 M20 15.0 1/2” 19.9 3/4” 6.5 13.9 12.5 20.9 0.4 1.0 30.5 33.6 73.0 20 E1FX 1RA PVC06 0.21
25S M25 15.0 3/4” 20.2 1” 11.1 19.9 14.0 22.0 0.4 1.2 37.5 41.3 89.0 25S E1FX 1RA PVC09 0.33
25 M25 15.0 3/4” 20.2 1” 11.1 19.9 18.2 26.2 0.4 1.2 37.5 41.3 89.0 25 E1FX 1RA PVC09 0.33
32 M32 15.0 1” 25.0 1 1/4” 17.0 26.2 23.7 33.9 0.4 1.2 46.0 50.6 86.0 32 E1FX 1RA PVC11 0.43
40 M40 15.0 1 1/4” 25.6 1 1/2” 22.0 32.1 27.9 40.4 0.4 1.6 55.0 60.5 90.0 40 E1FX 1RA PVC15 0.62
50S M50 15.0 1 1/2” 26.1 2” 29.5 38.1 35.2 46.7 0.4 1.6 60.0 66.0 91.0 50S E1FX 1RA PVC18 0.75
50 M50 15.0 2” 26.9 2 1/2” 35.6 44.0 40.4 53.0 0.6 1.6 70.1 77.1 95.0 50 E1FX 1RA PVC21 0.95
63S M63 15.0 2” 26.9 2 1/2” 40.1 49.9 45.6 59.4 0.6 1.6 75.0 82.5 102.0 63S E1FX 1RA PVC23 1.34
63 M63 15.0 2 1/2” 39.9 3” 47.2 55.9 54.6 65.8 0.6 1.6 80.0 88.0 104.0 63 E1FX 1RA PVC25 1.34
75S M75 15.0 2 1/2” 39.9 3” 52.8 61.9 59.0 72.0 0.6 1.6 90.0 99.0 115.0 75S E1FX 1RA PVC28 2.11
75 M75 15.0 3” 41.5 3 1/2” 59.1 67.9 66.7 78.4 0.6 1.6 100.0 110.0 117.0 75 E1FX 1RA PVC30 2.42
90 M90 24.0 3 1/2” 42.8 4” 66.6 78.6 76.2 90.3 0.8 1.6 114.3 125.4 147.0 90 E1FX 1RA PVC32 4.21
100 M100 24.0 4” 44.0 5” 76.0 90.9 86.1 101.4 0.8 1.6 123.0 135.3 140.0 100 E1FX 1RA LSF33 4.45
115 M115 24.0 4” 44.0 5” 86.0 97.9 101.5 110.2 0.8 1.6 133.4 146.7 162.0 115 E1FX 1RA LSF34 6.19
130 M130 24.0 5” 46.8 6” 97.0 114.9 110.2 123.2 0.8 1.6 152.4 167.6 174.0 130 E1FX 1RA LSF35 8.34
*Note : For material options please add the following suffix to change the Ordering Reference ; Brass (no suffix required), Nickel Plated Brass “5”, Copper Free Aluminium “1”
For NPT options add the following digits to the material suffix; 1/2” = 31; 3/4” = 32; 1” = 33; 1 1/4” = 34; 1 1/2” = 35; 2” = 36; 2 1/2” = 37; 3” = 38; 3 1/2” = 39; 4” = 310 (Brass requires prefix ‘0’)
Examples: 32E1FX1RA534 = Nickel Plated Brass 1-1/4” NPT, 50SE1FX1RA035 = Brass 1-1/2” NPT, 20E1FX1RA5 = Nickel Plated Brass M20
Dimensions are displayed in millimetres unless otherwise stated

TDS548 ISSUE6 08/15 www.cmp-products.com