A1

A.1 BASE PLATE DESIGN FOR 2028-SPS-009 frame 1

SUPPORT REACTION SUMMARY ( Refer Staad File 2028-SPS-003&004) :

Beam L/C Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm

Max Fx 4 351 OPERATING (D+L+WINDWEST) STR 6.696 30.991 0 0 0 -6.345

Min Fx 1 353 OPERATING (D+L+WINDEAST) STR -5.117 5.846 0 0 0 7.821

Max Fy 4 353 OPERATING (D+L+WINDEAST) STR -3.032 37.382 0 0 0 6.712

Min Fy 1 385 OPERATING (D+WINDE)STR/STB -4.971 3.548 0 0 0 7.35

Max Fz 4 344 OPERATING (D+L+WINDNORTH)STR 0.561 34.364 4.826 10.226 -0.12 1.297

Min Fz 4 346 OPERATING (D+L+WINDSOUTH)STR 0.561 34.364 -4.826 -10.226 0.12 1.297

Max Mx 4 344 OPERATING (D+L+WINDNORTH)STR 0.561 34.364 4.826 10.226 -0.12 1.297

Min Mx 4 346 OPERATING (D+L+WINDSOUTH)STR 0.561 34.364 -4.826 -10.226 0.12 1.297

Max My 4 346 OPERATING (D+L+WINDSOUTH)STR 0.561 34.364 -4.826 -10.226 0.12 1.297

Min My 4 344 OPERATING (D+L+WINDNORTH)STR 0.561 34.364 4.826 10.226 -0.12 1.297
Max Mz 1 353 OPERATING (D+L+WINDEAST) STR -5.117 5.846 0 0 0 7.821
Min Mz 4 383 OPERATING (D+WINDW)STR/STB 6.55 22.081 0 0 0 -6.681
 Horizontal Vertical Horizontal Moment
Node L/C Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
Max Fx 4 351 OPER 6.696 30.991 0 0 0 -6.345
Min Fx 1 353 OPER -5.117 5.846 0 0 0 7.821
Max Fy 4 353 OPER -3.032 37.382 0 0 0 6.712
Min Fy 1 385 OPER -4.971 3.548 0 0 0 7.35
Max Fz 4 344 OPER 0.561 34.364 4.826 10.226 -0.12 1.297
Min Fz 4 346 OPER 0.561 34.364 -4.826 -10.226 0.12 1.297
Max Mx 4 344 OPER 0.561 34.364 4.826 10.226 -0.12 1.297
Min Mx 4 346 OPER 0.561 34.364 -4.826 -10.226 0.12 1.297
Max My 4 346 OPER 0.561 34.364 -4.826 -10.226 0.12 1.297
Min My 4 344 OPER 0.561 34.364 4.826 10.226 -0.12 1.297
Max Mz 1 353 OPER -5.117 5.846 0 0 0 7.821
Min Mz 4 383 OPER 6.55 22.081 0 0 0 -6.681
 A 3+7

CALCULATION SHEET
Office
Mumbai Page No. Cont'n page No.

Job No. &

PJ 06/12/23
Title
60R95001 CAT FEED INJECTION Originator Date

Section AYP 06/12/23

STEEL DESIGN FOR PLATFORM STRUCTURE -EAST PAU 2 AND 3 Checker Date

ATTACHMENT E - PAU EAST 2 AND 3 PLATFORM Base plate Design

References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

H B

Ped size - 400 x 250

Column Section - PFC150X90X24

h= 150 mm

b= 90 mm

tf = 12 mm

tw = 6.5 mm

Base plate hb = 250 mm

bb = 180 mm

tp = 15 mm

c = 50 mm

Anchors M 16 A - 4.6

No.of bolts on ten. side = 1

Total No. of bolts = 2

Spacing of ha = 0 mm

anchors ba = 180 mm

edge distance e = 125 mm

fy for base plate 275 N/mm2

— Distribution of internal forces fy for rebar 500 N/mm2

Max. Axial Comp.+ Moment Factored reactions

(For base Plate design) Fsd.v = Ned = 33.64 KN

Fsd.H = 1.3 KN

Mx = 0 KNm

Mz = 0 KNm

Resultant M = Sqrt(Mx2 + Mz2) = 0 KNm

Distribution of internal forces

1
Z . F T , I , E + 2 (h−T f ). N Ed −M Ed = 0

Z= 0.5Z1 + ZT = 69 mm

Z1 = 150- 12 = 138 mm

ZT = 0/2 = 0 mm

0 E3 - 0.5 x138 x 33.64

=
69

= -33.64 KN hence FT,I,E = 0 KN

Ned/2+M/z1 = 16.8 KN
 A 4+7

CALCULATION SHEET
Office
Mumbai Page No. Cont'n page No.

Job No. &

PJ 06/12/23
Title
60R95001 CAT FEED INJECTION Originator Date

Section AYP 06/12/23

STEEL DESIGN FOR PLATFORM STRUCTURE -EAST PAU 2 AND 3 Checker Date

Min.
Axial
Comp.+
Moment
(For Anchor bolt design) Fsd.v = Ned = -2.4 KN

Fsd.H = 1.6 KN

Mx = 0 KNm

Mz = 0 KNm

Resultant M = Sqrt(Mx + Mz ) =
2 2
0 KNm

Distribution of internal forces

1
Z . F T , I , E + 2 (h−T f ). N Ed −M Ed = 0
Z= 0.5Z1 + ZT = 69 mm
Z1 = 150- 12 = 138 mm
ZT = 0/2 = 0 mm

0 E3 - 0.5 x138 x -2.4

=
69

= 2.4 KN hence FT,I,E = 2.4 KN

Ned/2+M/z1 = -1.2 KN

— Design bearing strength

fc Compressive strength of concrete γC Partial factor for concrete

fcd Design value of concrete compressive strength

αcc is the coefficient taking account of long term effects on the compressive strength and

of unfavourable effects resulting from the way the load is applied.

Note: The value of αcc for use in a Country should lie between 0,8 and 1,0 and may be found in its National

Annex. The recommended value is 0.85.

Concrete 28 ./ 35

as per EN-1992-1-1 CL. No. 3.1.6 Page 34

= 0.85 x 28/1.5

= 15.9 N/mm2

For a uniform distribution of load on an area Ac0 (see Figure ) the concentrated CL 6.7 PAGE 111
resistance force may be determined as follows:

FRdu = Ac0 ⋅ fcd ⋅( Ac1 / Ac0 )0.5 ≤ 3,0 ⋅ fcd ⋅ Ac0 where: Ac0 is the loaded area,
Ac1 is the maximum design distribution area with a similar shape to Ac0
 A 5+7

CALCULATION SHEET
Office
Mumbai Page No. Cont'n page No.

Job No. &

PJ 06/12/23
Title
60R95001 CAT FEED INJECTION Originator Date

Section AYP 06/12/23

STEEL DESIGN FOR PLATFORM STRUCTURE -EAST PAU 2 AND 3 Checker Date

Aco = b1 x d1 = 20160 mm2 Ac1 = b2 x d2 = 84000 mm2

b1 = beff = tf + min { c, (hb - h)/2 } + c = 12 + 50 + 50 = 112.0 mm (Refer sketch next

d1= leff = min{ bb, [b + (2 x c)] } = 180 mm 180 mm page)

b2 = min(H , 3xb1) = min(400, 3 x 112) = 336 mm

d2 = min(B , 3xd1) = min(250, 3 x 180) = 250 mm

Ac1 / Ac0 = 2.04

FRdu = 20160 x 15.9 x 2.04 = 653.9 KN 3 x fcd x Aco 961.632 KN

Hence FRdu 653.9 KN

The design bearing strength of the joint fjd should be determined from:

fjd = βj FRdu / (beff leff) ... (6.6) Page 68 EN 1993-1-8: 2003 (Design of joints)

where:

βj is the foundation joint material coefficient, which may be taken as 2/3 provided that the

characteristic strength of the grout is not less than 0,2 times the characteristic strength of the

concrete foundation and the thickness of the grout is not greater than 0,2 times the smallest width

of the steel base plate. In cases where the thickness of the grout is more than 50 mm, the

characteristic strength of the grout should be at least the same as that of the concrete foundation.

FRdu is the concentrated design resistance force given in EN 1992, where "Ac0 is to be taken as (beff leff).

0.67 x 653.9 / 20160 = 21.7 N/mm2

— Additional bearing width

EN-1993-1-8 6.2.5 pg 67

0.5
c= 15[ 275/ (3 x 21.7 x 1) ]

c= 30.8 mm < c =50mm

 A 6+7

CALCULATION SHEET
Office
Mumbai Page No. Cont'n page No.

Job No. &

PJ 06/12/23
Title
60R95001 CAT FEED INJECTION Originator Date

Section AYP 06/12/23

STEEL DESIGN FOR PLATFORM STRUCTURE -EAST PAU 2 AND 3 Checker Date

— Design compression resistance of T-stub as per EN-1993-1-8 - 6.2.6.9

Fig 6.4a Fig 6.4b

Max = MAX( 16.82 , -1.2 ) =

= 16.8 kN

EN 1993-1-8 2003 PG 67

beff = tf + min { c, (hb - h)/2 } + c =

12 + 50 + 50 = 112.0 mm

leff = min{ bb, [b + (2 x c)] } = 180 mm

FC,RD = 21.7 x 112 x 180

FC,RD = 437.5 KN > = 16.8 kN ok

— Verification of plate cross-section

Max FT,I,E = MAX( 0 , 2.4 ) = 2.4 kN

1/4 x 180 x 15^2 x 275 Table 6.2 EN 1993-1-8

1
 A 7+7

CALCULATION SHEET
Office
Mumbai Page No. Cont'n page No.

Job No. &

PJ 06/12/23
Title
60R95001 CAT FEED INJECTION Originator Date

Section AYP 06/12/23

STEEL DESIGN FOR PLATFORM STRUCTURE -EAST PAU 2 AND 3 Checker Date

— Anchors

For Anchor Bolt M 16 As = 157 mm2

Ultimate tensile strength Fub = 400 N/mm2

Tension Check

Max FT,I,E = MAX( 0 , 2.4 ) = 2.40 KN ( total tension in two bolts )

Ft,Ed = 2.40 KN tension per bolt

Allowable tension capacity of bolt

as per EN-1993-1-8, Table 3.4

0.9 x 400 x 157 = 45.216 KN

1.25
Ft,Ed < Ft,Rd OK

Shear Check

Max Shear = Fsd.H = MAX( 1.3 , 1.6 ) = 1.6 kN

= 0.3 x -1.2 = 0 KN Ff,Rd > Fsd.H

Friction between grout and plate is ignored as per EN-1993-1-8

Design shear resistance of the anchor bolts

By the 2 anchors in compression region :

= 0.248 also

0.248 x 400 x 157 = 12.46 kN

1.25

Total Shear resistance for 4 anchors = 0 + 4 x 12.46 =

= 49.8 kN > Fsd.H 1.6 kN OK

Combine Tension and shear check

For Max. Axial Comp.+ Moment

0.65 0.00 = 0.05 + 0 = 0.05 < 1

+
12.46 1.4 x 45.3 OK

For Min. Axial Comp.+ Moment

0.80 2.40 = 0.06 + 0.04 = 0.10 < 1

+
12.46 1.4 x 45.3 OK
 A 8+7

CALCULATION SHEET
Office
Mumbai Page No. Cont'n page No.

Job No. &

PJ 06/12/23
Title
60R95001 CAT FEED INJECTION Originator Date

Section AYP 06/12/23

STEEL DESIGN FOR PLATFORM STRUCTURE -EAST PAU 2 AND 3 Checker Date

— Thickness of base plate

2
2

t = Sqrt (4 x Mbp / fy )

trequired= 12 mm

tprovided= 15 mm Hence OK
 A 9+7
BASE PLATE DESIGN with Loadcase 144 and 131 Staad Node 13 and 2
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

H B

Ped size - 600 x 600

Column Section - UC203X203X46

h= 203.2 mm

b= 203.6 mm

tf = 11 mm

tw = 7.2 mm

Base plate hb = 450 mm

bb = 450 mm

tp = 20 mm

c = 123.4 mm

Anchors M 24 A - 4.6

No.of bolts on ten. side = 2

Total No. of bolts = 4

Spacing of ha = 300 mm

anchors ba = 300 mm

edge distance e = 75 mm

fy for base plate 355 N/mm2

— Distribution of internal forces fy for rebar 500 N/mm2

Max. Axial Comp.+ Moment Factored reactions

(For base Plate design) Fsd.v = Ned = 68 KN

Fsd.H = 14 KN

Mx = 2 KNm

Mz = 26 KNm

Resultant M = Sqrt(Mx2 + Mz2) = 26.1 KNm

Distribution of internal forces

1
Z . F T , I , E + 2 (h−T f ). N Ed −M Ed = 0

Z= 0.5Z1 + ZT = 246.1 mm

Z1 = 203.2- 11 = 192.2 mm

ZT = 300 / 2 = 150 mm

26.1 E3 - 0.5 x192.2 x 68

=
246.1

= 79.5 KN hence FT,I,E = 79.5 KN

= 147.5 KN
 A 10+7
BASE PLATE DESIGN with Loadcase 144 and 131 Staad Node 13 and 2
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

Min. Axial Comp.+ Moment (Factored reacions)

(For Anchor bolt design) Fsd.v = Ned = -36 KN

Fsd.H = 32 KN

Mx = 3 KNm

Mz = 7 KNm

Resultant M = Sqrt(Mx2 + Mz2) = 7.6 KNm

Distribution of internal forces

1
Z . F T , I , E + 2 (h−T f ). N Ed −M Ed = 0

Z= 0.5Z1 + ZT = 246.1 mm

Z1 = 203.2- 11 = 192.2 mm

ZT = 300 / 2 = 150 mm

7.6 E3 - 0.5 x192.2 x -36

=
246.1
= 44.94 KN hence FT,I,E = 80.94 KN
= 0.0 KN

— Design bearing strength

fc Compressive strength of concrete γC Partial factor for concrete

fcd Design value of concrete compressive strength

αcc is the coefficient taking account of long term effects on the compressive strength and

of unfavourable effects resulting from the way the load is applied.

Note: The value of αcc for use in a Country should lie between 0,8 and 1,0 and may be found in its National

Annex. The recommended value is 0.85.

Concrete C32 ./ 35

as per EN-1992-1-1 CL. No. 3.1.6 Page 34

= 0.85 x 32/1.5

= 18.10 N/mm2

For a uniform distribution of load on an area Ac0 (see Figure ) the concentrated CL 6.7 PAGE 111

resistance force may be determined as follows:

FRdu = Ac0 ⋅ fcd ⋅( Ac1 / Ac0 )0.5 ≤ 3,0 ⋅ fcd ⋅ Ac0 where: Ac0 is the loaded area,

Ac1 is the maximum design distribution area with a similar shape to Ac0
 A 11+7
BASE PLATE DESIGN with Loadcase 144 and 131 Staad Node 13 and 2
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

Aco = b1 x d1 = 116010 mm2 Ac1 = b2 x d2 = 360000 mm2

b1 = beff = tf + min { c, (hb - h)/2 } + c = 11 + 75 + 123.4 = 257.8 mm (Refer sketch

d1= leff = min{ bb, [b + (2 x c)] } = 450 mm 450 mm next page)

b2 = min(H , 3xb1) = min(600, 3 x 257.8) = 600 mm

d2 = min(B , 3xd1) = min(600, 3 x 450) = 600 mm

Ac1 / Ac0 = 1.76

FRdu = 116010 x 18.1 x 1.76 = 3695.6 KN 3 x fcd x Aco 6299.34 KN

Hence FRdu 3695.6 KN

The design bearing strength of the joint fjd should be determined from:

fjd = βj FRdu / (beff leff) ... (6.6) Page 68 EN 1993-1-8: 2003 (Design of joints)

where:

βj is the foundation joint material coefficient, which may be taken as 2/3 provided that the

characteristic strength of the grout is not less than 0,2 times the characteristic strength of the

concrete foundation and the thickness of the grout is not greater than 0,2 times the smallest width

of the steel base plate. In cases where the thickness of the grout is more than 50 mm, the

characteristic strength of the grout should be at least the same as that of the concrete foundation.

FRdu is the concentrated design resistance force given in EN 1992, where "Ac0 is to be taken as (beff leff).

0.67 x 3695.6 / 116010 = 21.3 N/mm2

— Additional bearing width

EN-1993-1-8 6.2.5 pg 67

0.5
c= 20[ 355/ (3 x 21.3 x 1) ]

c= 47.1 mm < c =123.4mm

 A 12+7
BASE PLATE DESIGN with Loadcase 144 and 131 Staad Node 13 and 2
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

— Design compression resistance of T-stub as per EN-1993-1-8 - 6.2.6.9

Fig 6.4a Fig 6.4b

Max = MAX( 147.5 , 0 ) =

= 147.5 kN

EN 1993-1-8 2003 PG 67

beff = tf + min { c, (hb - h)/2 } + c =

11 + 75 + 123.4 = 257.8 mm

leff = min{ bb, [b + (2 x c)] } = 450 mm

FC,RD = 21.3 x 257.8 x 450

FC,RD = 2471 KN > = 147.5 kN ok

— Verification of plate cross-section

Max FT,I,E = MAX( 79.5 , 44.94 ) = 80.9 kN

1/4 x 450 x 20^2 x 355 Table 6.2 EN 1993-1-8

 A 13+7
BASE PLATE DESIGN with Loadcase 144 and 131 Staad Node 13 and 2
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

16 KNm

( 300 - 203.2 ) /2 = 48.4 mm

16 = 330.5785124 > 80.9 kN ok

0.0484

— Anchors

For Anchor Bolt M 24 As = 353 mm2

Ultimate tensile strength Fub = 400 N/mm2

Tension Check

Max FT,I,E = MAX( 79.5 , 80.94 ) = 80.94 KN ( total tension in two bolts )

Ft,Ed = 40.47 KN tension per bolt

Allowable tension capacity of bolt

as per EN-1993-1-8, Table 3.4

0.9 x 400 x 353 = 101.664 KN

1.25
Ft,Ed < Ft,Rd OK

Shear Check

Max Shear = Fsd.H = MAX( 14 , 32 ) = 32 kN

= 0.3 x 0 = 0 KN Ff,Rd > Fsd.H

Friction between grout and plate is ignored as per EN-1993-1-8

Design shear resistance of the anchor bolts

By the 2 anchors in compression region :

= 0.248 also

0.248 x 400 x 353 = 28.01 kN

1.25

Total Shear resistance for 4 anchors = 0 + 4 x 28.01 =

= 112.0 kN > Fsd.H 32 kN OK

Combine Tension and shear check

3.50 40.47 = 0.12 + 0.28 = 0.41 < 1

+
28.01 1.4 x 101.7 therefore ok
 A 14+7
BASE PLATE DESIGN with Loadcase 144 and 131 Staad Node 13 and 2
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

— Thickness of base plate

2
= 21.3 x47.1 = 23626 Nmm

t = Sqrt (4 x Mbp / fy )

trequired= 16 mm

tprovided= 20 mm Hence OK

— Check for Anchor bolt Embedment length

Bar to be fully stressed? N

Area of rebar required, Ast = Tu = 40 = 89.933 mm2

0.9 fy 0.9 x 0.5

Rebar used: 20 Number of rebars resisting tension, N = 1

Area of steel provided, Arebar =1 * 314 = 314.0 mm2 > 89.933 mm2 OK

σb,sd = T/Abar = 40.47 x 1000 / 314 = 129 N/mm2 ..Ref. cl 8.4 of EN-1992-1-1:2005(E)

Required embedment length:

lbd = α1 x α2 x α3 x α4 x α5 x lb, reqd

= 1 x 1 x 1 x 1 x 1x lb, reqd

lb, reqd = f x ssd fbd = 2.25 x n1 x n2 x fctd ….cl 8.4.2

4x x fbd = 2.25 x 1 x 1x fctd

fctd = a ct x fctk 0.05 / gc

75mm
= 1 x 2.08/ 1.5 N/mm2

= 1.386666667 N/mm2

330mm
fbd = 2.25 x 1 x 1 x 1.3867

= 3.12 N/mm2
75mm

lb, reqd = 20 x 129

4 x 3.12

= 206.55

lbd = 1 x 1 x 1 x 1 x 1x 206.547

= 206.55 mm

X = distance from bolt to bar = 60 mm

Y = X tan 35 = 42 mm
 A 15+7

BASE PLATE DESIGN with Loadcase 144 and 131 Staad Node 13 and 2
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

Projection = 80 mm Grout = 25 mm

Total Bolt Length required = 404 mm Total Bolt length provided = 510 mm O.K.
 BASE PLATE DESIGN with Loadcase 141 and 132 Staad Node 3 and 13
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

H B

Ped size - 600 x 600

Column Section - UC203X203X46

h= 203.2 mm

b= 203.6 mm

tf = 11 mm

tw = 7.2 mm

Base plate hb = 450 mm

bb = 450 mm

tp = 20 mm

c = 123.4 mm

Anchors M 24 A - 4.6

No.of bolts on ten. side = 2

Total No. of bolts = 4

Spacing of ha = 300 mm

anchors ba = 300 mm

edge distance e = 75 mm

fy for base plate 355 N/mm2

— Distribution of internal forces fy for rebar 500 N/mm2

Max. Axial Comp.+ Moment Factored reactions

(For base Plate design) Fsd.v = Ned = 2.42 KN

Fsd.H = 40 KN

Mx = 4 KNm

Mz = 14.5 KNm

Resultant M = Sqrt(M + M ) =
x
2
z
2
15 KNm

Distribution of internal forces

1
Z . F T , I , E + 2 (h−T f ). N Ed −M Ed = 0

Z= 0.5Z1 + ZT = 246.1 mm

Z1 = 203.2- 11 = 192.2 mm

ZT = 300 / 2 = 150 mm

15 E3 - 0.5 x192.2 x 2.42

=
246.1

= 60.01 KN hence FT,I,E = 60.01 KN

= 62.4 KN
 BASE PLATE DESIGN with Loadcase 141 and 132 Staad Node 3 and 13
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

Min. Axial Comp.+ Moment (Factored reacions)

(For Anchor bolt design) Fsd.v = Ned = -29.5 KN

Fsd.H = 5 KN

Mx = 1.65 KNm

Mz = 10 KNm

Resultant M = Sqrt(Mx2 + Mz2) = 10.1 KNm

Distribution of internal forces

1
Z . F T , I , E + 2 (h−T f ). N Ed −M Ed = 0

Z= 0.5Z1 + ZT = 246.1 mm

Z1 = 203.2- 11 = 192.2 mm

ZT = 300 / 2 = 150 mm

10.1 E3 - 0.5 x192.2 x -29.5

=
246.1
= 52.56 KN

= 82.1 KN

— Design bearing strength

fc Compressive strength of concrete γC Partial factor for concrete

fcd Design value of concrete compressive strength

αcc is the coefficient taking account of long term effects on the compressive strength and

of unfavourable effects resulting from the way the load is applied.

Note: The value of αcc for use in a Country should lie between 0,8 and 1,0 and may be found in its National

Annex. The recommended value is 0.85.

Concrete C32 ./ 35

as per EN-1992-1-1 CL. No. 3.1.6 Page 34

= 0.85 x 32/1.5

= 18.10 N/mm2

For a uniform distribution of load on an area Ac0 (see Figure ) the concentrated CL 6.7 PAGE 111

resistance force may be determined as follows:

FRdu = Ac0 ⋅ fcd ⋅( Ac1 / Ac0 )0.5 ≤ 3,0 ⋅ fcd ⋅ Ac0 where: Ac0 is the loaded area,

Ac1 is the maximum design distribution area with a similar shape to Ac0
 BASE PLATE DESIGN with Loadcase 141 and 132 Staad Node 3 and 13
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

Aco = b1 x d1 = 116010 mm2 Ac1 = b2 x d2 = 360000 mm2

b1 = beff = tf + min { c, (hb - h)/2 } + c = 11 + 75 + 123.4 = 257.8 mm (Refer sketch

d1= leff = min{ bb, [b + (2 x c)] } = 450 mm 450 mm next page)

b2 = min(H , 3xb1) = min(600, 3 x 257.8) = 600 mm

d2 = min(B , 3xd1) = min(600, 3 x 450) = 600 mm

Ac1 / Ac0 = 1.76

FRdu = 116010 x 18.1 x 1.76 = 3695.6 KN 3 x fcd x Aco 6299.34 KN

Hence FRdu 3695.6 KN

The design bearing strength of the joint fjd should be determined from:

fjd = βj FRdu / (beff leff) ... (6.6) Page 68 EN 1993-1-8: 2003 (Design of joints)

where:

βj is the foundation joint material coefficient, which may be taken as 2/3 provided that the

characteristic strength of the grout is not less than 0,2 times the characteristic strength of the

concrete foundation and the thickness of the grout is not greater than 0,2 times the smallest width

of the steel base plate. In cases where the thickness of the grout is more than 50 mm, the

characteristic strength of the grout should be at least the same as that of the concrete foundation.

FRdu is the concentrated design resistance force given in EN 1992, where "Ac0 is to be taken as (beff leff).

0.67 x 3695.6 / 116010 = 21.3 N/mm2

— Additional bearing width

EN-1993-1-8 6.2.5 pg 67

0.5
c= 20[ 355/ (3 x 21.3 x 1) ]

c= 47.1 mm < c =123.4mm

 BASE PLATE DESIGN with Loadcase 141 and 132 Staad Node 3 and 13
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

— Design compression resistance of T-stub as per EN-1993-1-8 - 6.2.6.9

Fig 6.4a Fig 6.4b

Max = MAX( 62.4 , 82.1 ) =

= 82.1 kN

EN 1993-1-8 2003 PG 67

beff = tf + min { c, (hb - h)/2 } + c =

11 + 75 + 123.4 = 257.8 mm

leff = min{ bb, [b + (2 x c)] } = 450 mm

FC,RD = 21.3 x 257.8 x 450

FC,RD = 2471 KN > = 82.1 kN ok

— Verification of plate cross-section

Max FT,I,E = MAX( 60.01 , 52.56 ) = 82.1 kN

1/4 x 450 x 20^2 x 355 Table 6.2 EN 1993-1-8

 BASE PLATE DESIGN with Loadcase 141 and 132 Staad Node 3 and 13
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

16 KNm

( 300 - 203.2 ) /2 = 48.4 mm

16 = 330.5785124 > 82.1 kN ok

0.0484

— Anchors

For Anchor Bolt M 24 As = 353 mm2

Ultimate tensile strength Fub = 400 N/mm2

Tension Check

Max FT,I,E = MAX( 60.01 , 82.1 ) = 82.10 KN ( total tension in two bolts )

Ft,Ed = 41.05 KN tension per bolt

Allowable tension capacity of bolt

as per EN-1993-1-8, Table 3.4

0.9 x 400 x 353 = 101.664 KN

1.25
Ft,Ed < Ft,Rd OK

Shear Check

Max Shear = Fsd.H = MAX( 40 , 5 ) = 40 kN

= 0.3 x 82.1 = 0 KN Ff,Rd > Fsd.H

Friction between grout and plate is ignored as per EN-1993-1-8

Design shear resistance of the anchor bolts

By the 2 anchors in compression region :

= 0.248 also

0.248 x 400 x 353 = 28.01 kN

1.25

Total Shear resistance for 4 anchors = 0 + 4 x 28.01 =

= 112.0 kN > Fsd.H 40 kN OK

Combine Tension and shear check

10.00 41.05 = 0.36 + 0.29 = 0.65 < 1

+
28.01 1.4 x 101.7 therefore ok
 BASE PLATE DESIGN with Loadcase 141 and 132 Staad Node 3 and 13
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

— Thickness of base plate

2
= 21.3 x47.1 = 23626 Nmm

t = Sqrt (4 x Mbp / fy )

trequired= 16 mm

tprovided= 20 mm Hence OK

— Check for Anchor bolt Embedment length

Bar to be fully stressed? N

Area of rebar required, Ast = Tu = 41 = 91.222 mm2

0.9 fy 0.9 x 0.5

Rebar used: 20 Number of rebars resisting tension, N = 1

Area of steel provided, Arebar =1 * 314 = 314.0 mm2 > 91.222 mm2 OK

σb,sd = T/Abar = 41.05 x 1000 / 314 = 131 N/mm2 ..Ref. cl 8.4 of EN-1992-1-1:2005(E)

Required embedment length:

lbd = α1 x α2 x α3 x α4 x α5 x lb, reqd

= 1 x 1 x 1 x 1 x 1x lb, reqd

lb, reqd = f x ssd fbd = 2.25 x n1 x n2 x fctd ….cl 8.4.2

4x x fbd = 2.25 x 1 x 1x fctd

fctd = a ct x fctk 0.05 / gc

75mm
= 1 x 2.08/ 1.5 N/mm2

= 1.386666667 N/mm2

330mm
fbd = 2.25 x 1 x 1 x 1.3867

= 3.12 N/mm2
75mm

lb, reqd = 20 x 131

4 x 3.12

= 209.51

lbd = 1 x 1 x 1 x 1 x 1x 209.5072

= 209.51 mm

X = distance from bolt to bar = 60 mm

Y = X tan 35 = 42 mm
 BASE PLATE DESIGN with Loadcase 141 and 132 Staad Node 3 and 13
References EC2 Part 1 of 1 EN 1992-1-1 2004

EC3 Part 1 of 8 EN 1993-1-8 2003

Projection = 75 mm Grout = 25 mm

Total Bolt Length required = 402 mm Total Bolt length provided = 405 mm O.K.
 SHEAR LUG DESIGN

300

300

600

#REF!
G=25

Grout H=100

Shear Lug
25.000

Input Data:

Column Loadings:
Shear Load, V(total) = 116.00 KN
Axial Load, P(DL) = 0 KN

Base and Shear Lug Data:

Base Plate Length, N = #REF! mm
Base Plate Width, B = #REF! mm
Base Plate Thk., tp = #REF! mm
Grout Thickness, G = 25.00 mm
Lug Height, H = 100.00 mm
 Lug Width, W = 250.00 mm
Lug Thickness, t = 25.000 mm
Weld Size, w = 6.0000 mm
Lug Yield Stress, Fy = 355.00 N/mm2
Coef. of Friction, m = 0.55
Pier Length, Lpx = 600.000 mm
Pier Width, Lpy = 600.000 mm
Concrete Strength, f 'c = 32 N/mm2

Shear Lug Design Loads:

Shear, V(lg) = V-1/2*m*ABS(P(DL)) Friction between grout and plate is ignored

116.00 kN

Moment, M(lg) = (V(lg)/W)*(H+G)/2

(116/250)* (100+25)/2 = 29000 Nmm

Shear Lug Thickness:

t(req'd) = Sqrt (4 x Mbp / fy )

18.08 mm t(req'd) <= t, O.K.

Concrete Bearing at Lug:

fp = V/(W*(H-G)) = 6.19 N/mm2

Bearing strength of concrete = Fp = 0.6*(f'c) 19.2 N/mm2

Fp >= fp, O.K.

Concrete Shear in Front of Lug:

Width of Shear area = 600 mm

Depth of Shear area = 400 mm
Av = (600 * 400 ) - ( 250 * 100) = 215000 mm2
Vc = x Av 635.27 kN

Vc >=V, O.K.

Shear Lug Welding:

Ultimate fillet weld capacity for S355 baseplate with and shear key joined at 90deg

Weld s = 6.0000 mm
Throat thickness = 0.707s= 4.242 mm
Longitudinal capacity = 1.05 kN/mm Refer Table
472.5 kN

Weld capacity >= req'd., O.K.

4.3.1 Design of Anchor bolts and base plate for PSC-802-330

H B

Ped size - 650 x 650

Column Section - HE240B

tf = 14 mm

Base plate hb = 450 mm

bb = 450 mm

tp = 20 mm

assume c = 105 mm

Anchors M 20 Z - 8.8

Fub = 800

No of bolts on one side = 2

Spacing of anchors

ha = 300

ba = 300

edge distance e = 75

Loads for LC 206 node 15

Fsd.v = Ned = 15.43 KN

Fsd.H = 2.83 KN

Mx = 8.7 KNm

Mz = 0 KNm

Resultant M = Sqrt(Mx2 + Mz2) = 8.7 KNm

Distribution of internal forces

= 0

Z= 0.5Z1 + ZT = 263 mm

Z1 = 240- 14 = 226 mm

ZT = 300 / 2 = 150 mm

8.7 E3 - 0.5 x226 x 15.43

=
263

= 26.45 KN

= 41.9 KN
Design bearing strength

Concrete C28 ./ 35

as per EN-1992-1-1 Cl. No. 3.15

= 1 x 28/1.5

= 18.70 N/mm2

Aco = b1 x d1 = 1E+05 mm2 Ac1 = b2 x d2 = 5E+05 mm2

b1 = beff = tf + 2c = 14 + 2 x 105 = 224.0 mm

d1 = bp = 450 mm

b2 = 224+ 2 x 75 = 374 mm

d2 = 3 x 450 = 1350 mm

Ac1 / Ac0 = 2.24

FRdu = 100800 x 18.7 x 2.24 = 4222.3 KN

0.67 x 4222.3 / 100800 = 28.1 N/mm2

Additional bearing width

as per EN-1993-1-8-6.2.5
0.5
C= 20[ 235 / (3 x fjd x Ymo ) ]

20[ 235 / (3 x 28.1 x 1) ] 0.5

C= 33.4 mm < overhang

Design compression resistance of T-stub

Fig.6.4b as per EN-1993-1-8 - 6.2.6.9

beff = 75 + 14 + 33.4

beff = 122.4 mm

leff = bp = 450 mm

FC,RD = 28.1 x 122.4 x 450

FC,RD = 1547.7 KN > = 41.9 ok

Verification of plate cross-section

0.25 x 450 x 20^2 x 235

10.6 KNm

( 300 - 240 ) = 30 mm

10.6 = 353.33 > 26.5 ok

0.03

Anchors

= 26.5 KN ( total tension in two bolts )

= 13.225 KN tension per bolt

Allowable tension capacity of bolt

as per EN-1993-1-8-6.2.5

Table 3.4

0.9 x 800 x 244.9 = 141.062 KN > 13.225 ok

1.25
Thickness of base plate

2
= 28.1 x33.4 = 15674 Nmm

t = Sqrt (6 x Mbp / fy )

t = 20 mm

therefore base plate provided of thickness 20 mm is ok

Shear check

= .0.2 x 41.9 = 8.38 KN Ff,Rd > Fsd.H

as per EN-1993-1-8-6.2.5

Design shear resistance of the anchor bolts

By the 2 anchors in compression region :

= 0.6

fyb = 640

also

therefore

0.6 x 800 x 244.9 = 94.0416

1.25

for 2 anchors 188.08 KN > Fsd.H = 2.83 KN

Combination Tension and shear

0.71 13.225 = 0.01 + 0.07 = 0.07 < 1

+
94.042 1.4 x 141.1 therefore ok