Cemfix GP

General purpose, cementitious tile adhesive with high slip resistance for
internal and external use

DESCRIPTION
TECHNICAL PROPERTIES. W/P = 0.32
Cemfix GP is a general purpose, polymer modified cement
based tile adhesive for bonding all types of ceramic tiles Colour: White or grey
and stone on most common construction substrates Fresh wet density: 1.7 ± 0.1 g/cm³
for internal and external applications using the thin bed
method. Pot life:
2:30 hr @ 25oC
BDS EN 1015-9
Cemfix GP is supplied in the form of white or grey powder
that is ready to use with the addition of water to provide a Open time:
30 min
good workable and easy to apply tile adhesive. BDS EN 1346
Consistency:
Since it has excellent slip resistance properties, Cemfix GP ≈ 150 mm
BDS EN 1015-3
is suitable to be applied vertically without sagging and with
no need for using spacers for normal sized tiles. Cemfix Tensile adhesion strength in compliance with BDS
GP can be used in wet or dry conditions. EN 1348
Initial bond @ 28 days ≥ 1.0 MPa
APPLICATIONS
After heat exposure ≥ 1.0 MPa
After water immersion ≥ 1.0 MPa
» For wall and floor applications. After freeze/thaw ≥ 1.0 MPa
» Suitable for exterior and interior applications. cycles
» Can be used in wet areas such as bathrooms and
kitchens. Open time - tensile
» On concrete, cement based mortar, screed and plaster. bond strength after 30
> 0.5 MPa
» On drywall such as gypsum boards and cement boards. min.:
BDS EN 1346
ADVANTAGES
Slip:
≤ 0.5 mm
BDS EN 1308
» High bond strength.
» For ceramic, granite and stone tiles. VOC: ≤ 10 g/ltr
» Extended open time for easier application. ASTM D2369 (comply with LEED)
» Easy to apply, non-sag with good workability.
» Ready mixed, just requires addition of water.
» Water and frost resistant. METHOD OF USE
» Economical.
SUBSTRATE PREPARATION
LIMITATIONS
All surfaces must be clean, dry and free from dust, oil,
Do not use for: grease, paints or any loose material.

» Thick bed applications. Concrete and cement based substrates must be sufficiently
» Tile over tile applications. cured and dimensionally stable. Allow time for shrinkage
» Cases that require a rapid utilization for the surfaces. and structural strain movements.
» On metal, rubber, PVC or wood substrates.
Plaster based substrates must be primed with Grundix
STANDARDS contact+. Tiles should not be placed over expansion
and contraction joints, these joints should be filled with a
Cemfix GP complies with BS EN 12004 as an improved suitable flexible sealant from the DCP Flexseal range.
cementitious tile adhesive with slip resistance, extended
open time (C2TE).
Cemfix GP
MIXING CLEANING

To ensure proper mixing, a mechanically powered mixer or All tools should be cleaned immediately after use with
drill fitted with suitable paddle should be used. fresh clean water. Hardened materials should be cleaned
mechanically.
7.75 - 8.25 litres of clean fresh water for each 25 kg bag
(water/powder ratio of 0.31 - 0.33 by weight) should be REMARKS
added to a clean container. The powder is then added
slowly to the water while mixing continuously at low speed » The laying of the tiles should only be carried out when
(400 - 600 rpm). substrate and ambient temperature are in the range of
5 to 25°C.
Mixing time should be continued for 3 minutes until a » For large format and heavy tiles, it is good practice to
uniform consistency and free of lumps mixture is obtained. back butter the tile back surfaces with the adhesive to
Allow a slake time for 10 minutes, then remix for additional ensure 100% coverage. The joint for large tiles must be
1 minute without adding any more water. at least 3 mm.
» Protect the applied adhesive for 24 hours from high
APPLICATION temperatures, wetting and freezing
» For large format and heavy tiles where the weight
» Apply the adhesive to the substrate using a notched of the tiles cannot be supported by the adhesive,
trowel with teeth size 8 x 8 or 10 x 10 mm. With a very the installation method shall follow a bottom-up
flat base, you can also use a 6 x 6 mm screed. The approach, and If more than two rows of tiles are to be
maximum thickness of the adhesive layer should not fixed simultaneously, the tiles are to be mechanically
exceed 2 cm. When laying tiles on a wall, comb the supported using temporary anchor nails in between tile
adhesive with the trowel only in a horizontal direction gaps or by using inclined support stud.
(parallel to the floor).
» Place the tiles with firm pressure and tap them into place For further information please contact your local DCP
with a rubber hammer to ensure proper contact with the Representation Office.
adhesive without leaving any voids or air bubbles.
» It is always better to work in a manageable area that PACKAGING
can be tiled within the open wet time of the adhesive.
» Leave a minimum 2 mm joint between the tiles. The
Cemfix GP is available in 25 kg bags.
joint prevents possible movements in the base and
guarantees the strength and durability of the adhesives.
YIELD
For rooms larger than 36 m², provide expansion joints.
» Immediately after work, clean the faces of the tiles from
adhesive with a damp sponge. Approximately 6.4 m² per 25 kg bag @ 3 mm thickness.
» Allow 24 hours for the adhesive to dry completely and
clean the joints between the tiles with a sharp tool and STORAGE
then with a brush before proceeding with grouting.
» Cemafill PRO tile grout is recommended to its tested Cemfix GP has a shelf life of 12 months from date of
compatibility with the Cemfix GP adhesive. You can manufacture if stored at temperatures between 2°C and
choose from 25 contemporary and fresh colors. Cemafill 30°C.
PRO has antibacterial ingredients and is resistant to
cracking. If these conditions are exceeded, DCP Technical
» For the corners of wet rooms and bathrooms, use the Department should be contacted for advice.
sanitary silicone Flexseal AS122.
 Cemfix GP
CAUTIONS

HEALTH AND SAFETY

As Cemfix GP contains Portland cement and sand, Cemfix

For further information refer to the Material Safety Data

FIRE

Cemfix GP is nonflammable.

MORE FROM DON CONSTRUCTION PRODUCTS

A wide range of construction chemical products are

» Concrete admixtures.
» Surface treatments
» Grouts and anchors.
» Concrete repair.
» Flooring systems.
» Protective coatings.
» Sealants.
» Waterproofing.
» Adhesives.
» Tile adhesives and grouts.
» Building products.
» Structural strengthening.
 10-0005-A-2022
Cemfix GP