Scribd
Upload
143 views

MICRO PILE Miq-Makmal-Meyerhoff Formula

The document provides calculations for the geotechnical capacity of piles based on borehole 7 using the Meyerhof formulae, with details on pile size, soil types and properties at different depths, calculations for skin friction and base pressure, and determination that a 150mm pile of 7.075m length would have sufficient capacity to support an applied load of 100kN per pile. Safety factors of 2 for skin friction and 3 for base pressure were used in the design.

Uploaded by

Naziemi Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
143 views

MICRO PILE Miq-Makmal-Meyerhoff Formula

The document provides calculations for the geotechnical capacity of piles based on borehole 7 using the Meyerhof formulae, with details on pile size, soil types and properties at different depths, calculations for skin friction and base pressure, and determination that a 150mm pile of 7.075m length would have sufficient capacity to support an applied load of 100kN per pile. Safety factors of 2 for skin friction and 3 for base pressure were used in the design.

Uploaded by

Naziemi Ahmad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 9

BW PERUNDING SDN. BHD. COMPANY NO.

27875 P

CALCULATION SHEET SHEET

JOB: Semanggol Contract No: MIQ


Part of Work: MIXING CHAMBER
Group: Structural Assistant: ABA Checked by:
Date: December 11, 2023 File:
'file:///conversion/tmp/activity_task_scratch/711924865.xls'#$load at base

Total Weight for base at level 5.30

Base level +6.00 1 x 9.325 x 4 x 0.5 x 24 = 448

Wall 1 2 x 9.325 x 5.95 x 0.5 x 24 = 1332

Wall 2 1 x 4 x 5.95 x 0.5 x 24 = 286

Wall 3 1 x 3 x 1.5 x 0.35 x 24 = 38

Wall 4 1 x 3 x 4.87 x 0.35 x 24 = 123

Wall 5 1 x 3 x 3.95 x 0.3 x 24 = 85

Wall 6 1 x 3 x 5.45 x 2.25 x 24 = 883

Walkway 1 1 x 10.725 x 0.7 x 0.15 x 24 = 27

Walkway 2 1 x 4 x 0.7 x 0.15 x 24 = 10

Water 1 x 8.35 x 3 x 5.45 x 10 = 1365

Imposed load 1 x 3 = 3 kN

TOTAL 4599

Total Weight = 4599 kN


extra 20 % of Total Weight = 5519 kN
Project: TWPS- Semanggol -Kontrak 1

Client: LAP
Location: Makmal
Subject: GEOTECHNICAL CAPACITY OF PILES BASED ON BH 7
USING MEYERHOF FORMULAE
File location 'file:///conversion/tmp/activity_task_scratch/711924865.xls'#$pile dsgn_ meyerhoff-size 150

Original Ground Level(OGL) : 0.0 m

Pile size 150


Type of soil
Sand = 1, Silt =2
Base area= 0.017671459 m2
Perimeter= 0.471238898 m
F.O.S for skin friction= 2
F.O.S for base pressure= 3
Limiting Skin Friction= Ton/m2
Recomm. Structural capacity= 24 tonnes
Meyerhof Formulae:-
Qsu =0.2*Nave*As for sand Nave= Average SPT value along the shaft
Qbu=40*N*Ab for sand N= SPT value at pile base
Qsu =0.17*Nave*As for silt As= Area of pile shaft Qu= Qsu+Qbu
Qbu=25*N*Ab for silt Ab= Area of pile base Qw=Qu/S.F

Layer Depth Thick SPT Nave Type Shaft Qsu (Qsu)sum Qbu Qw
(m) (m) N' of area Ton at depth
Value Soil (m2) (Ton) (Ton) (Ton) LEVEL
1(OGL) 0.00 0.00 0 0.0 1 0.00 0.00 0.00 0.00 0.00 0.000
2 1.50 1.50 4 2.0 1 0.71 0.28 0.28 2.83 1.08 -1.500
3 3.00 1.50 3 3.5 2 0.71 0.42 0.70 1.33 0.79 -3.000
4 4.50 1.50 21 12.0 2 0.71 1.44 2.15 9.28 4.17 -4.500
5 6.00 1.50 27 24.0 2 0.71 2.88 5.03 11.93 6.49 -6.000
6 7.50 1.50 50 38.5 2 0.71 4.63 9.66 22.09 12.19 -7.500
7 9.00 1.50 50 50.0 2 0.71 6.01 15.66 22.09 15.20 -9.000
8 10.50 1.50 50 50.0 2 0.71 6.01 21.67 22.09 18.20 -10.500
9 12.00 1.50 50 50.0 2 0.71 6.01 27.68 22.09 21.20 -12.000
10 13.50 1.50 50 50.0 2 0.71 6.01 33.69 22.09 24.21 -13.500
11 15.00 1.50 50 50.0 2 0.71 6.01 39.70 22.09 27.21 -15.000
12 16.50 1.50 50 50.0 2 0.71 6.01 45.71 22.09 30.22 -16.500
13 18.00 1.50 50 50.0 2 0.71 6.01 51.71 22.09 33.22 -18.000

SUMMARY OF PILE DESIGN CALCULATION USING MEYERHOFF FORMULA


Note: GEOTECHNICAL CAPACITY OF PILES BASED ON BH 7
F.O.S for skin friction= 2
F.O.S for base pressure= 3

Total Load at base level +5.50m = 100.0 kN = 100.0 kN


1.0 nos of piles

Geotechnical
Capacity Per
Pile (kN) =

Size Of Pile Applied suitable


Actual 121.91 Quick FOS level length
No(s) of Proposed Load Per Remarks so level cut level for
Load Check
Ground level bottom of pile
pile(s) (mm) Pile (kN) of pile (m) bottom of
(kN) So for design base (m) req (m)
pile (m)
stage, load per
pile should be

120

100.0 1.0 150 100.00 120.00 1.200 OK!! 7.620 7.120 7.195 0.120 7.075

Nos of Piles Length of Piles (m)


1.0 7.075
Project: TWPS- Semanggol -Kontrak 1

Client: LAP
Location: Makmal
Subject: GEOTECHNICAL CAPACITY OF PILES BASED ON BH 7
USING MEYERHOF FORMULAE
File location 'file:///conversion/tmp/activity_task_scratch/711924865.xls'#$pile dsgn_ meyerhoff-size150(2)

Original Ground Level(OGL) : 0.0 m

Pile size 150


Type of soil
Sand = 1, Silt =2
Base area= 0.017671459 m2
Perimeter= 0.471238898 m
F.O.S for skin friction= 2
F.O.S for base pressure= 3
Limiting Skin Friction= Ton/m2
Recomm. Structural capacity= 24 tonnes
Meyerhof Formulae:-
Qsu =0.2*Nave*As for sand Nave= Average SPT value along the shaft
Qbu=40*N*Ab for sand N= SPT value at pile base
Qsu =0.17*Nave*As for silt As= Area of pile shaft Qu= Qsu+Qbu
Qbu=25*N*Ab for silt Ab= Area of pile base Qw=Qu/S.F

Layer Depth Thick SPT Nave Type Shaft Qsu (Qsu)sum Qbu Qw
(m) (m) N' of area Ton at depth
Value Soil (m2) (Ton) (Ton) (Ton) LEVEL
1(OGL) 0.00 0.00 0 0.0 1 0.00 0.00 0.00 0.00 0.00 0.000
2 1.50 1.50 4 2.0 1 0.71 0.28 0.28 2.83 1.08 -1.500
3 3.00 1.50 3 3.5 2 0.71 0.42 0.70 1.33 0.79 -3.000
4 4.50 1.50 21 12.0 2 0.71 1.44 2.15 9.28 4.17 -4.500
5 6.00 1.50 27 24.0 2 0.71 2.88 5.03 11.93 6.49 -6.000
6 7.50 1.50 50 38.5 2 0.71 4.63 9.66 22.09 12.19 -7.500
7 9.00 1.50 50 50.0 2 0.71 6.01 15.66 22.09 15.20 -9.000
8 10.50 1.50 50 50.0 2 0.71 6.01 21.67 22.09 18.20 -10.500
9 12.00 1.50 50 50.0 2 0.71 6.01 27.68 22.09 21.20 -12.000
10 13.50 1.50 50 50.0 2 0.71 6.01 33.69 22.09 24.21 -13.500
11 15.00 1.50 50 50.0 2 0.71 6.01 39.70 22.09 27.21 -15.000
12 16.50 1.50 50 50.0 2 0.71 6.01 45.71 22.09 30.22 -16.500
13 18.00 1.50 50 50.0 2 0.71 6.01 51.71 22.09 33.22 -18.000

SUMMARY OF PILE DESIGN CALCULATION USING MEYERHOFF FORMULA


Note: GEOTECHNICAL CAPACITY OF PILES BASED ON BH 7
F.O.S for skin friction= 2
F.O.S for base pressure= 3

Total Load at base level +5.50m = 190.0 kN = 95.0 kN


2.0 nos of piles

Geotechnical
Capacity Per
Pile (kN) =

Size Of Pile Applied suitable


Actual 121.91 Quick FOS level length
No(s) of Proposed Load Per Remarks so level cut level for
Load Check
Ground level bottom of pile
pile(s) (mm) Pile (kN) of pile (m) bottom of
(kN) So for design base (m) req (m)
pile (m)
stage, load per
pile should be

120

190.0 2.0 150 95.00 120.00 1.263 OK!! 7.620 7.120 7.195 0.120 7.075

Nos of Piles Length of Piles (m)


2.0 7.075
Micropile arragement at Makmal Gu

5 m ( casing & API


pipe)

2 m (steel casing)

3m m
(API) (API)

Length of API = 8 m Length of API =


Length of casing = 7 m Length of casing =
Nos of piles = 20 nos Nos of piles =
Nos of joint = 2 nos Nos of joint =

Micropile size = 150 mm diameter


API pipe size = OD= 88.9 mm
t= 6.45 mm
assume length of API pipe = 7.00 mm
assume weigth of steel = 7850.00 kg/m3

Calculation

804.013 Bore vertical hole. 160 m

804.014 Cement grout 2.83 m2

804.015 Steel casing 140 m


804.016 cutt off pile head 20 nos

804.017 API pipe OD area =


inside area =

total volume =

total weight =

804.018 no of point 20 nos

804.019
weld to extension of casing

804.020 18.8 m
weld to extension of API pipe
rragement at Makmal Gunung Semanggol (Kontrak 1)

m ( casing & API m ( casing & API


pipe) pipe)

m (steel casing)
m (steel casing)

m
(API)

0 m Length of API = 0 m
0 m Length of casing = 0 m
0 nos Nos of piles = 0 nos
0 nos Nos of joint = 0 nos

Plate = 230 x230x10


400x400x10- hollow 177

Calculation in BQ

160 m

10 m2

140 m
20 nos

0.00621
0.00534

0.139 m3

1,090.2 kg 1,100.0 kg

20 nos

20 m

20 m
m ( casing & API
pipe)

m (steel casing)

You might also like