INSTALLATION MANUAL

Bolden™ Single Handle

Pull Down Kitchen Faucet

KPF-1610

www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I Rev. March 29, 2023
Congratulations on the purchase of your new
Kraus plumbing fixture!
R

Please keep the box and packaging materials until your product is
completely installed. If you have any questions, require technical
assistance or have any problems with your product:

STOP DO NOT RETURN TO STORE

Please contact our Customer Service Team

1-800-775-0703 / [email protected]

Have the model number available and retain a copy of your

receipt with purchase date for reference.

If for any reason this product does not meet your expectations,
please be sure to repack this product in the original box and
packaging material to avoid damage during transit.

2
 STOP

Prior to Installation:

· Make sure you have all necessary parts by checking the diagram and
parts list. If any part is missing or damaged, please contact Kraus
R

Customer Service at 800-775-0703 for a replacement.

· Read all instructions and safety warnings and ensure you have all tools,
parts, and equipment necessary for a safe installation.

· Turn off the hot and cold water supply at the angle stops and turn on
the old faucet to release any built up pressure. Remove existing faucet.

· Pre-drilled hole size requirement: 1 3/8" (min)

· Max countertop thickness: 1 3/4”

For technical assistance or replacement parts, please contact Kraus Customer

Service and one of our representatives will be happy to help:
Toll-Free: 800-775-0703 or [email protected]

Tools Required

Adjustable Wrench Phillips Screwdriver Silicone Sealant Safety Goggles Pipe Tape

Care & Maintenance

* To keep the product clean & shining, follow the steps below:

1. Rinse with clean water & dry with a soft cloth

2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners ACID
3. Do not use cloth with a coarse surface
4. Unscrew the aerator and clean when necessary

* This installation manual is subject to change without further notice.

3
Diagram and Parts List

A. Spray Head
B. Faucet Body
C. Mounting Hardware
C1. Rubber & Metal
Washer
C2. Mounting Nut
C3. Mounting Screws
B D. Quick Connector
E. Weight
A E1. Weight Clip
E2. Weight
F. 2.5mm Hex Wrench

E1
C1
C2
E2 C3 F

4
 Faucet Dimensions

10 3/4"
(274mm)
(456mm)

3 1/2"
18"

(88mm)

25°
Ø1 7/8" 8 3/4"
(48mm)
(221mm)

90°
6 3/8"
(162mm)
4 1/2"
(116mm)

2 1/4"
(56mm)

Ø2 1/8"
(54mm)
(432mm)
17"

22 3/4"
(578mm)

3/8" compression

Installer Tip:

Shut off main water supply before installing new faucet.

5
Step 1. Remove mounting hardware

Shut off the water supply. Remove the

old faucet. Clean the mounting surface.
Remove mounting hardware (C) from
faucet body (B).

Step 2. Installing the faucet assembly

Optional No Escutcheon Installation.

Insert faucet body through the hole in
the sink or countertop.

6
Step 3. Securing the faucet assembly

Install the rubber washer and metal

washer (C1) onto the threaded
mounting shank. Thread the nut (C2)
onto the mounting shank. Lock the
nut (C2) into position by tightening
the screws (C3). Do not overtighten.

C1
C2
C3

Step 4. Securing the faucet assembly

Push the quick connector (D) firmly

upward and attach it to the receiving
block (1). Pull down moderately to
ensure the connection has been made.

7
Step 5. Installing the counterweight

Install the weight clip (E1) at the point

of the hose marking "weight here".
Insert the weight (E2) onto the clip
(E1) by sliding it down onto the clip
(E1).

Weight
here
E2
E2
E1 Weight
here

E1

Step 6. Making the waterline connections

Thread the nut (1) on the supply line

onto the outlet of the water supply
valve and tighten with a wrench. Do
1 not overtighten.

NOTE: Please make sure filter

washers are installed before
connecting to the main valve.

8
Step 7. Flushing and checking for leaks

Pull the hose assembly out of the spout and

remove the spray head by unscrewing it from
the hose in a counterclockwise direction. Be
sure to hold the end of the hose down into the
sink and turn the faucet on to the warm
position where it mixes hot and cold water.
Flush the water lines for one minute. This
flushes away any debris that could cause
damage to internal parts. Check for leaks.
Retighten any connections if necessary, but do
not overtighten. Reinstall the spray head by
hand tightening it back onto the spray hose.
After installation is completed, turn on the hot
and cold water supplies. Check for leaks.

9
 Replacement Parts
Replacement Finish/Color Part #
Parts List
1. Sprayer CH,SFS,SS,SB,MB,SFSB,BG,BB KP27216
6
SFACB,SFACBMB,BGMB**
4
2. Screen Washer KP27208
5 3. Sprayer Hose BLBG,BLMB,BLSFS,BLSS,GRCH KP27247
BLSFACB,GRSFS,GRSS,BLBB*
7 4. Flow Regulator WH** KP27074
7.1 Assembly (1.8GPM)
7.2 5. Quick Connector KP27090
8 Assembly
9
3 10 6. Spring Assembly CH,MB,SB,SFS,BG,SS,SFSB** KP27220
11
12 6. Spring Assembly SFACB,BB** KP27322
7. Sprayer Holder CH,SFS,SS,SB,SFSMB,BG,SFACB,BB KP27218
MB,SFACBMB,BGMB,SFSB,MBSB,
13 Assembly SFSCH,SSCH,SSMB,MBSFSB,BBMB**
2 16 14
15 7.1. Inverter KP27245
1 19 17
20 7.2. Wearable Ring & KP27085
24 18 O-ring Assembly
21 8. Set Screw KP27084
23 9. Index BL,GR** KP27124
22 10. Cartridge Kerox KP27083
K-35
*Denotes spray hose assembly color options:
Spray hose assembly color options: Black hose w/Brushed
11. Bonnet Nut KP27082
Gold connector (BLBG), Black hose with Spot-Free 12. Cap CH, SFS, SS, SB, MB, KP27081
Stainless connector (BLSFS), Gray hose with Chrome BG, SFACB, SFSB, BB**
connector (GRCH), Gray hose with Spot-Free Stainless 13. Handle Assembly CH, SFS, SS, SB, MB, KP27072
connector (GRSFS), Gray hose with Stainless Steel BG, SFACB, SFSB, BB**
connector (GRSS), Black hose with Matte Black connector 14. Set Screw KP27001
(BLMB), Black hose with Stainless Steel connector (BLSS), 15. Cover Button BL,GR** KP27002
Black hose with Spot-Free Antique Champagne Bronze 16. Washer KP27091
(BLSFACB), Black hose with Brushed Brass (BLBB) 17. Rubber & Metal KP27028
**Denotes faucet component color options: Washer
CH - Chrome
18. Mounting Nut & KP27079
SFS - Spot Free Stainless Steel
SS - Stainless Steel Screws
MB - Matte Black 19. Block KP27073
BG - Brushed Gold 20. O-ring KP27092
SB - Black Stainless
BB - Brushed Brass 21. Weight & Clip KP27236
MBSFSB - Matte Black/Spot Free Black Stainless Assembly
SFACB - Spot Free Antique Champagne Bronze 22. Hex Wrench KP27020
MBSB - Matte Black/Black Stainless
SFSCH - Spot Free Stainless Steel/Chrome 23. Inverter KP27123
BGMB - Brushed Gold/Matte Black 24. Filter Washers KP27167
SFSB - Spot Free Black Stainless
SFSMB - Spot Free Stainless Steel/Matte Black
SSMB - Stainless Steel/Matte Black
SSCH - Stainless Steel/Chrome
BBMB - Brushed Brass/Matte Black
SFACBMB - Spot Free Antique Champagne Bronze/Matte Black
BL - Black WH - White GR- Grey

10
Troubleshooting
If you have followed the instructions carefully and your faucet still does not work properly,
take the following corrective steps:

PROBLEM CAUSE ACTION

Leakage under faucet handle Bonnet nut (11) has Remove the cover button (15). Loosen set
come loose screw (14) with hex wrench (22). Remove
the handle. Unscrew cap (12). Tighten
bonnet nut (11) with an adjustable wrench.

The aerator has an The aerator is dirty or Remove the aerator and check for debris.
irregular or reduced mis-fitted Ensure that the rubber washer is properly
water flow installed.

The water pressure The connector underneath Turn off the water supply and disconnect
is low. the deck is clogged with debris the connector / aerator. Unscrew the
connector / aerator and clean under
The aerator is clogged running water. Screw the connector /
aerator back.
Test water flow. If water pressure is still low
then replace the connector / aerator.

There is a low flow of The screen filters in the Turn off the water supply at the water
water. hose connectors are dirty. valves and unscrew the hose connectors
from the water supply lines. Clean the
screens in the water lines with hot water,
removing any debris or calcium build up.

11
Codes/Standards Applicable:

NSF/ANSI 372 NSF/ANSI/CAN 61: Q ≤ 1 LEAD FREE

UP UP IA
P
ASME A112.18.1
NSF/ANSI 61
MO
C C R&
T
1.8GPM 6.8L/min maximum
C R
C R TM

Faucet - Lifetime Limited Warranty

Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the
R

Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is
non-transferable.

Kraus warrants the structure and finish of the Faucet to be free from defects in material and workmanship under normal
usage for as long as the original purchaser resides in the residence in which the Faucet was first installed.

Kraus warrants the Faucet's sprayhead assembly (including the engine, aerators, structure, restrictors, back flow
preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel) of the product
to be free from defects in material and workmanship under normal usage for a period of one (1) year from the date of
purchase.

Kraus warrants the Faucet's cartridge to be free from defects in material and workmanship under normal usage for a
period of five (5) years from the date of purchase.

Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired
or replaced with a product of equal value at the option of Kraus.

Commercial Warranty

Kraus USA Plumbing, LLC (“Kraus”) warrants its Products for a period of one (1) year to commercial purchasers of
Products used in industrial, commercial and business applications.

Care and Cleaning Instructions

Certain cleaning products may cause damage to a Product's finish and use of the following on the Product will void this
warranty:

• Abrasive cleaners such as powders, bleach, ammonia, alcohol or chorine

• Abrasive pads, steel wool or wire brushes

What is Not Covered

This warranty does not cover Products that were discontinued when purchased or display Products, whether such
Products were purchased at discount outlets, unauthorized dealers, and/or sold on clearance. This warranty does not
cover any free gifts included with purchase.

This warranty does not cover damage resulting from neglect, misuse (including use for an unintended application),
abuse, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, improper maintenance,
alteration of the Product, or failure to follow care, cleaning or installation instructions enclosed with your Product. Kraus
recommends that all Kraus Products be installed by a fully licensed and insured trade professional with experience in the
installation of bathroom and/or kitchen manufactured goods.

12
How to Make a Warranty Claim

If you are a consumer purchaser, please contact a Kraus Customer Service Representative at:
R

Kraus USA Plumbing, LLC

12 Harbor Park Drive
Port Washington, NY 11050
Toll-free 800-775-0703
[email protected]

If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8955
[email protected]

If you are an authorized partner, please contact a Partner Support Representative at:
Kraus USA Plumbing, LLC
12 Harbor Park Drive
Port Washington, NY 11050
516-801-8954
[email protected]

In requesting warranty service, please be ready to provide your proof of purchase and a description of the problem. Shipping charges
will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply).
International shipping fees are not included.

Limitation on Duration of Implied Warranties

Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the
below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY,
INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO
THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.

Limitation of Special, Incidental or Consequential Damages

Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental or
consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND KRAUS USA PLUMBING, LLC SHALL NOT BE LIABLE FOR, ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS
PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR
OTHERWISE.

This warranty gives you specific legal rights, and you may also have other rights which vary from state/province to state/province.

Download the Kraus Care & Maintenance Guide at:

http://www.kraususa.com/maintenance

13
 IMPORTANT

Register Your Kraus Product

Activate Your Warranty

Access Premium Customer Support
Get Product Information

REGISTER TODAY
http://www.kraususa.com/registration

www.kraususa.com