Data sheet 6ES7131-6BF01-0BA0

SIMATIC ET 200SP, Digital input module, DI 8x 24V DC Standard, type 3

(IEC 61131), sink input, (PNP, P-reading), Packing unit: 1 piece, fits to BU-
type A0, Colour Code CC01, input delay time 0,05..20ms, module
diagnostics for: short-circuit of sensor supply, wire break, supply voltage

General information
Product type designation DI 8x24 VDC ST
HW functional status From FS02
Firmware version V0.0
● FW update possible No
usable BaseUnits BU type A0
Color code for module-specific color identification plate CC01
Product function
● I&M data Yes; I&M0 to I&M3
● Isochronous mode No
Engineering with
● STEP 7 TIA Portal configurable/integrated from V14
version
● STEP 7 configurable/integrated from version V5.5 SP3 or higher
● PCS 7 configurable/integrated from version V8.1 SP1
● PROFIBUS from GSD version/GSD revision One GSD file each, Revision 3 and 5 and higher
● PROFINET from GSD version/GSD revision GSDML V2.3
Operating mode
● DI Yes
● Counter No
● Oversampling No
● MSI No
Supply voltage
Rated value (DC) 24 V
permissible range, lower limit (DC) 19.2 V
permissible range, upper limit (DC) 28.8 V
Reverse polarity protection Yes
Input current
Current consumption, max. 50 mA; All channels are supplied from the encoder supply
Encoder supply
Number of outputs 8
Output voltage, min. 19.2 V
Short-circuit protection Yes; per module
24 V encoder supply
● 24 V Yes
● Short-circuit protection Yes
● Output current, max. 700 mA
● Output current per channel, max. 700 mA
● Output current per module, max. 700 mA

6ES71316BF010BA0 Subject to change without notice

6/15/2022
Page 1/3 © Copyright Siemens
Power loss
Power loss, typ. 1 W; 24 V, 8 inputs supplied via encoder supply
Address area
Address space per module
● Inputs 1 byte; + 1 byte for QI information
Hardware configuration
Automatic encoding Yes
● Mechanical coding element Yes
● Type of mechanical coding element Type A
Selection of BaseUnit for connection variants
● 1-wire connection BU type A0
● 2-wire connection BU type A0
● 3-wire connection BU type A0 with AUX terminals or potential distributor module
● 4-wire connection BU type A0 + Potential distributor module
Digital inputs
Number of digital inputs 8
Digital inputs, parameterizable Yes
Source/sink input P-reading
Input characteristic curve in accordance with IEC 61131, Yes
type 3
Input voltage
● Rated value (DC) 24 V
● for signal "0" -30 to +5 V
● for signal "1" +11 to +30V
Input current
● for signal "1", typ. 2.5 mA
Input delay (for rated value of input voltage)
for standard inputs
— parameterizable Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay
of 30 to 500 µs, depending on line length)
— at "0" to "1", min. 0.05 ms
— at "0" to "1", max. 20 ms
— at "1" to "0", min. 0.05 ms
— at "1" to "0", max. 20 ms
Cable length
● shielded, max. 1 000 m
● unshielded, max. 600 m
Encoder
Connectable encoders
● 2-wire sensor Yes
— permissible quiescent current (2-wire sensor), 1.5 mA
max.
Interrupts/diagnostics/status information
Diagnostics function Yes
Alarms
● Diagnostic alarm Yes
Diagnoses
● Diagnostic information readable Yes
● Monitoring the supply voltage Yes
— parameterizable Yes
● Monitoring of encoder power supply Yes; Module-by-module, optional protective circuit for preventing wire-
break diagnostics in the case of simple encoder contacts: 25 kOhm to
45 kOhm
● Wire-break Yes; Module-wise
● Short-circuit Yes; Module-wise
Diagnostics indication LED
● Monitoring of the supply voltage (PWR-LED) Yes; green PWR LED
● Channel status display Yes; green LED
● for channel diagnostics No
● for module diagnostics Yes; green/red DIAG LED

6ES71316BF010BA0 Subject to change without notice

6/15/2022
Page 2/3 © Copyright Siemens
Potential separation
Potential separation channels
● between the channels No
● between the channels and backplane bus Yes
● between the channels and the power supply of the No
electronics
Isolation
Isolation tested with 707 V DC (type test)
Standards, approvals, certificates
Suitable for safety functions No
Ambient conditions
Ambient temperature during operation
● horizontal installation, min. -30 °C; < 0 °C as of FS02
● horizontal installation, max. 60 °C
● vertical installation, min. -30 °C; < 0 °C as of FS02
● vertical installation, max. 50 °C
Altitude during operation relating to sea level
● Installation altitude above sea level, max. 5 000 m; Restrictions for installation altitudes > 2 000 m, see manual
Dimensions
Width 15 mm
Height 73 mm
Depth 58 mm
Weights
Weight, approx. 28 g

last modified: 9/24/2021

6ES71316BF010BA0 Subject to change without notice

6/15/2022
Page 3/3 © Copyright Siemens