CS609- System Programming

Solved MCQS genrica

From Midterm Papers

https://genrica.com Virtual University

MIDTERM EXAMINATION
CS609- System Programming

Question No: 1 ( Marks: 1 ) - Please choose one

DMA stands for_________

►Direct Memory Access (Page 4)

►Distinct Memory Access
►Direct Module Access
►Direct Memory Allocation

Question No: 2 ( Marks: 1 ) - Please choose one

Standard PC operates in two modes in terms of memory which are

►Real mode and Extended Mode

►Base mode and Memory Mode
►None of the given
►Real mode and protected mode (Page 6)

Question No: 3 ( Marks: 1 ) - Please choose one

UART stands for_______

►Universal Asynchronous Receiver Transmitter (Page 107)

►Universal Adjustment and Realigning Tool
►Unconventional Assisted Recovery Team
►None of these

Question No: 4 ( Marks: 1 ) - Please choose one

Usually interrupt procedures are reentrant procedures especially those interrupt procedure compiled using C
language compiler are reentrant.
►True (Page 38)
►False

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 5 ( Marks: 1 ) - Please choose one
DTE is ____________.

►Data terminal equipment (Page 109)

►Data transmitting equipment
►Dual terminal equipment
►None of the given.

Question No: 6 (Marks: 1) - Please choose one

Interrupt Vector Table (IVT) in short is a _______ bytes sized table.

►1024 (Page 10)

►2048
►3072
►4096

Question No: 7 ( Marks: 1 ) - Please choose one

Hardware Interrupts are __________.

►Preemptive
►Non-Preemptive (Page 48)
►Both Preemptive and Non-Preemptive
►None of Given

Question No: 8 (Marks: 1) - Please choose one

Timer interrupt is a _________.

►Hardware Interrupt (Page 28)

►Software Interrupt
►Both of these
►None of These

Question No: 9 ( Marks: 1 ) - Please choose one

Int 14H __________ can be used to set the line parameter of the UART or COM port.

►Service # 0 (Page 119)

► Service # 1
►Service # 2
►None of the given options

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 10 ( Marks: 1 ) - Please choose one
The keyboard makes use of interrupt number _______ for its input operations.
►9 (Page 34)
►10
►11
►12

Question No: 11 ( Marks: 1 ) - Please choose one

In self test mode the output of the UART is routed to its input.

►True (Page 117)

►False

Question No: 12 ( Marks: 1 ) - Please choose one

In case of synchronous communication a timing signal is required to identify the start and end of a bit.

►True (Page 105)

►False

Question No: 13 ( Marks: 1 ) - Please choose one

Register can be used to divide frequency is _________

►Counter Register (Page 69)

►Accumulator Register
►None of these

Question No: 14 ( Marks: 1 ) - Please choose one

Only ________ ports are important from programming point of view.

► 70 and 71H (Page 141)

►71 and 72H
►70 and 72H
►72 and 73H

Question No: 15 ( Marks: 1 ) - Please choose one

Which port is known as Data Port______
►60H (Page 177)
►61H
►64H
►69H

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 16 ( Marks: 1 ) - Please choose one
LPTs can be swapped.
►True (Page 92)
►False

Question No: 17 ( Marks: 1 ) - Please choose one

PPI is used to perform parallel communication
►True (Page 81)
►False

Question No: 18 ( Marks: 1 ) - Please choose one

__________is used to control the printer via the BIOS

►Int 16H
►Int 17H (Page 84)
►Int 18H
►Int 19H

Question No: 19 ( Marks: 1 ) - Please choose one

_____ bit is cleared to indicate the low nibble is being sent.

►D1
►D2
►D3
►D4 (Page 104)

Question No: 20 ( Marks: 1 ) - Please choose one

DSR stands for __________ .

►Data set ready (Page 111)

►Data service ready
►Data stock ready
►None of the given

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
 MIDTERM EXAMINATION
CS609- System Programming

Question No: 1 ( Marks: 1 ) - Please choose one

There are two main types of interrupts namely _________________.

►PC based and Window based

►Hardware based and Kernal based
►Hardware interrupts and Software interrupts (Page 10)
►None of the given

Question No: 2 ( Marks: 1 ) - Please choose one

To set the interrupt vector means is to change the double word sized interrupt vector within the IVT.

►True (Page 22)

►False

Question No: 3 ( Marks: 1 ) - Please choose one

The service number is usually placed in the ________ register.
►AL
►CL
►AH (Page 26)
►AX

Question No: 4 ( Marks: 1 ) - Please choose one

The keyboard makes use of interrupt number _______ for its input operations.
► 9 (Page 34)
►10
►11
►12

Question No: 5 ( Marks: 1 ) - Please choose one

The service _________ is called the keyboard hook service.

►15H/2FH
►15H/4FH (Page 44)
►15H/FFH

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 6 ( Marks: 1 ) - Please choose one
The BIOS interrupt ________ can be used to configure RTC.

►1AH (Page 136)

►2AH
►3AH
►4AH

Question No: 7 ( Marks: 1 ) - Please choose one

The interval timer can operate in _______ modes.

►Five
►Seven
►Four
►Six (Page 72)

Question No: 8 ( Marks: 1 ) - Please choose one

______ is Disk interrupt.
►10H
►11H
►13H (Page 42)
►14H

Question No: 9 ( Marks: 1 ) - Please choose one

PPI stands for
►Parallel Programmable interface
►Peripheral Programmable interface (Page 76)
►Port Programmable interface
►None of the given

Question No: 10 ( Marks: 1 ) - Please choose one

Int ________ is used to control the printer via the BIOS.
►17H (Page 84)
►18H
►20H
►21H

Question No: 11 ( Marks: 1 ) - Please choose one

Counter register can be used to divide clock signal.
►True (Page 69)
►False

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 12 ( Marks: 1 ) - Please choose one
DCE stands for __________.

►Data communication equipment (Page 109)

►Distributed Computing Environment
►Data Communications Equipment
►Data Carrier Equipment

Question No: 13 ( Marks: 1 ) - Please choose one

_________ is used to identify the cause of interrupt.

►Interrupt ID Register (Page 116)

►PC Register
►AC Register
►None of All These

Question No: 14 ( Marks: 1 ) - Please choose one

The bit number _______ of the coprocessor control word is the interrupt enable flag.

►7 (Page 168)
►8
►9
►6

Question No: 15 ( Marks: 1 ) - Please choose one

There are __________ kinds of serial communication.

►2 (Page 105)
►3
►4
►5

Question No: 16 ( Marks: 1 ) - Please choose one

________ store the base address for LPT1.

►40:00H
►40:02H
►40:08H (Page 92)
►40:1AH

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 17 ( Marks: 1 ) - Please choose one
The amount of memory above conventional memory (extended memory) can be determined using the service
_______.

►15H/88H (Page 162)

►16H/88H
►17H/88H
►21H/88H

Question No: 18 ( Marks: 1 ) - Please choose one

The output on the monitor is controlled by a controller called __________within the PC.

►Video controller (Page 30)

►Bus controller
►Ram controller
►None of the given

Question No: 19 ( Marks: 1 ) - Please choose one

The keyboard input character scan code is received at ___ port.

►60H (Page 179)

►61H
►62H
►63H

Question No: 20 ( Marks: 1 ) - Please choose one

_______ is LED control byte.

►0xFD
►0xED (Page 181)
►0xFF
►0xEE

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
 MIDTERM EXAMINATION
CS609- System Programming

Question No: 1 ( Marks: 1 ) - Please choose one

There are two main types of interrupts, namely

►PC based and Window based

►Hardware based and Kernal based
►Hardware interrupts and Software interrupts (Page 10) rep
►None of the given

Question No: 2 ( Marks: 1 ) - Please choose one

Standard PC operates in two modes in terms of memory which are

►Real mode and Extended Mode

►Base mode and Memory Mode
►None of the given
►Real mode and protected mode (Page 6) rep

Question No: 3 ( Marks: 1 ) - Please choose one

BPB stands for _________.
►BIOS parameter block (Page 243)
►BIOS processing block
►Base processing block
►BIOS partition block

Question No: 4 ( Marks: 1 ) - Please choose one

The Function of I/O controller is to provide ____________.

►I/O control signals

►Buffering
►Error Correction and Detection
►All of given (Page 5)

Question No: 5 ( Marks: 1 ) - Please choose one

IVT is a table containing ______ byte entries each of which is a far address of an interrupt service routine.
►2
►4 (Page 20)
►8
►16

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 6 ( Marks: 1 ) - Please choose one
Each paragraph in keep function is ____ bytes in size.

►4
►8
►16 (Page 24)
►32

Question No: 7 ( Marks: 1 ) - Please choose one

Interrupt 9 usually reads the _________ from keyboard.
►ASCII code
►Scan code (Page 34)
►Both ASCII and Scan code
►None of the above

Question No: 8 ( Marks: 1 ) - Please choose one

A software interrupt does not require EOI (End of interrupt).
►True (Page 49)
►False

Question No: 9 ( Marks: 1 ) - Please choose one

To store each character in keyboard buffer ____ bytes are required.
►2 (Page 54)
►4
►6
►8

Question No: 10 ( Marks: 1 ) - Please choose one

Interrupt _____ is empty; we can use its vector as a flag.

►9H
►13H
►15H
►65H (Page 65)

Question No: 11 ( Marks: 1 ) - Please choose one

Command register is an _____ bit register

►4
►8 (Page 71)
►16
►32

10

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 12 ( Marks: 1 ) - Please choose one
The interval timer can operate in ____modes.

►Three
►Four
►Five
►Six (Page 72) rep

Question No: 13 ( Marks: 1 ) - Please choose one

The following command “outportb (0x61,inportb(0x61) | 3);” will ________ .
►Turn on the speaker (Page 74)
►Turn off the speaker
►Toggle the speaker
►None of the above

Question No: 14 ( Marks: 1 ) - Please choose one

The PPI acts as an interface between the CPU and a parallel ________ .
►I/O device (Page 83)
►CPU
►BUS
►None of Given

Question No: 15 ( Marks: 1 ) - Please choose one

DTE is ____________.
►Data terminal equipment (Page 109) rep
►Data transmitting equipment
►Dual terminal equipment
►None of the given.

Question No: 16 ( Marks: 1 ) - Please choose one

DSR stands for __________ .

►Data set ready (Page 111) rep

►Data service ready
►Data stock ready
►None of the given

Question No: 17 ( Marks: 1 ) - Please choose one

In self test mode the output of the UART is routed to its input.

►True (Page 117) rep

►False

11

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 18 ( Marks: 1 ) - Please choose one
Interrupt ______ is used to get or set the time.

►0AH
►1AH (Page 136)
►2AH
►3AH

Question No: 19 ( Marks: 1 ) - Please choose one

______ is used to set time.

►1A/02H
►1A/03H (Page 138)
►1A/04H
►1A/05H

Question No: 20 ( Marks: 1 ) - Please choose one

Communication between keyboard and keyboard controller is __________.

►Asynchronous serial
►Synchronous serial (not sure)
►Parallel communication
►None of the given

MIDTERM EXAMINATION
CS609- System Programming

Question No: 1 ( Marks: 1 ) - Please choose one

Following is not a method of I/O

►Programmed I/O
► Interrupt driven I/O
►Hardware Based I/O (Page 4)
►None of given

12

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 2 ( Marks: 1 ) - Please choose one
The Function of I/O controller is to provide ____________.
►I/O control signals
►Buffering
►Error Correction and Detection
►All of given (Page 5) rep

Question No: 3 ( Marks: 1 ) - Please choose one

Which of the following are types of ISR __________.

►BIOS (Basic I/O service ) ISR

►DOS ISR
►ISR provided by third party device drivers
►All of the given (Page 13)

Question No: 4 ( Marks: 1 ) - Please choose one

Interrupt service number is usually placed in ____________ register.
►CH
►CL
►AH (Page 26) rep
►AL

Question No: 5 ( Marks: 1 ) - Please choose one

NMI Stand for

►Non Maskable Interrupt (Page 46)

►Non Multitude Interrupt
►Non Maskable Instruction
►None of Given

Question No: 6 ( Marks: 1 ) - Please choose one

A single interrupt controller can arbitrate among ____ different devices.
►4
►6
►8 (Page 47)
►10

Question No: 7 ( Marks: 1 ) - Please choose one

Hardware Interrupts are __________.
►Preemptive
►Non-Preemptive (Page 48) rep
►Both Preemptive and Non-Preemptive
►None of Given

13

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 8 ( Marks: 1 ) - Please choose one
The microprocessor package has many signals for data. Below are some in Correct priority order (Higher to
Lower).

►Reset,Hold,NMI,INTR (Page 46)

►NMI, INTR,Hold,Reset
►INTR,NMI,Reset,Hold
►None of the Given

Question No: 9 ( Marks: 1 ) - Please choose one

The interval timer can operate in ____modes.

►Three
►Four
►Five
►Six (Page 72) rep

Question No: 10 ( Marks: 1 ) - Please choose one

PPI stands for _____________.

►Parallel Programmable interface

►Peripheral Programmable interface (Page 76) rep
►Port Programmable interface
►None of the given

Question No: 11 ( Marks: 1 ) - Please choose one

The following command “outportb (0x61,inportb(0x61) & 0xFC);” will

►Turn on the speaker (Page 74)

►Turn off the speaker
►Toggle the speaker
►None of the given

Question No: 12 ( Marks: 1 ) - Please choose one

The PPI acts as an interface between the CPU and a parallel ________ .

►I/O device (Page 83) rep

►CPU
►BUS
►None of Given

14

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 13 ( Marks: 1 ) - Please choose one
BIOS DO NOT support ______.

►LPT1
►LPT2
►LPT3
►LPT4 (Page 91)

Question No: 14 ( Marks: 1 ) - Please choose one

_____ bit is cleared to indicate the low nibble is being sent.

►D1
►D2
►D3
►D4 (Page 101)

Question No: 15 ( Marks: 1 ) - Please choose one

The bit ______ of Line control register in UART, if cleared will indicate that DLL is the data register.

►1
►3
►5
►7 (Page 114)

Question No: 16 ( Marks: 1 ) - Please choose one

Int 14H __________ can be used to set the line parameter of the UART or COM port.

►Service # 0 (Page 119) rep

►Service # 1
►Service # 2
►Service # 3

Question No: 17 ( Marks: 1 ) - Please choose one

_________ used to determine the amount of conventional memory interfaced with the processor in kilobytes.

►INT 10 H
►INT 11 H
►INT 12 H (Page 162)
►INT 13 H

15

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 18 ( Marks: 1 ) - Please choose one
Bit number _______ of coprocessor control word is the Interrupt Enable Flag.

►7 (Page 168)
►8
►9
►10

Question No: 19 ( Marks: 1 ) - Please choose one

To distinguish 486 with Pentium CPUID Test is used.

►True (Page 166)

►False

Question No: 20 ( Marks: 1 ) - Please choose one

______ is LED control byte.

►0xF3
►0xED (Page 181) rep
►0xE5
►0xFF

MIDTERM EXAMINATION
CS609- System Programming

Question No: 1 ( Marks: 1 ) - Please choose one

The memory addresses of COM ports remain same for all computers

►True
►False

Question No: 2 ( Marks: 1 ) - Please choose one

Int_____________ service 0 can be used to set the line parameter of the UART or COM port.

►14H (Page 119)

►15H
►13H
►None of the given option

16

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 3 ( Marks: 1 ) - Please choose one
In case of synchronous communication a timing signal is required to identify the start and end of a bit.

►True (Page 105) rep

►False

Question No: 4 ( Marks: 1 ) - Please choose one

BIOS support _____________UARTS as COM ports.
►6
►4 (Page 113)
►3
►2

Question No: 5 ( Marks: 1 ) - Please choose one

The________ function uses the COM port number to receive a byte from the COM port using BIOS services.
►recievebyte()
►initialize ()
►receive()
►recievechar() (Page 125)

Question No: 6 ( Marks: 1 ) - Please choose one

DTE is ___________
►Data terminal equipment (Page 109) rep
►Data transmitting equipment
►Dual terminal equipment
►None of above

Question No: 7 ( Marks: 1 ) - Please choose one

Int 14H____________ can be used to send a byte

►Service#0
►Service#1 (Page 121)
►Service#2
►None of the given option.

Question No: 8 ( Marks: 1 ) - Please choose one

Int 14H______ can be used to set the line parameter of the UART or COM port

►Service#0 (Page 119) rep

►Service#1
►Service#2
►None of the given option

17

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 9 ( Marks: 1 ) - Please choose one
The ________function initialize the COM port whose number is passed as parameter using BIOS services.

►Initializecom()
►Initialize() (Page 125)
►Recievechar()
►None of these option

Question No: 10 ( Marks: 1 ) - Please choose one

____whenever received indicates the start of communication and ______ whenever received indicates a
temporary pause in the communication.

►XON & XOFF (Page 135)

►XOFF & XON
►XON & YOFF
►YON & XOFF

Question No: 11 ( Marks: 1 ) - Please choose one

___________ is used to identify cause of interrupt.

►Interrupt enable register

►Interrupt ID register (Page 116) rep
►Interrupt Status register
►None of the above

Question No: 12 ( Marks: 1 ) - Please choose one

In ____________each byte is needed to be encapsulated in start and end.

►Synchronous communication
►Asynchronous communication (Page 106)
►Both
►None of given

Question No: 13 ( Marks: 1 ) - Please choose one

________ is a device incorporated into the PC to update time even if the computer is off.

►Clock counter
►ROM
►Clock
►Real time clock (Page 136)

18

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question No: 14 ( Marks: 1 ) - Please choose one
There are two type of communication synchronous and Anti Synchronous
►True
►False (Page 105)

Question No: 15 ( Marks: 1 ) - Please choose one

The ____________ function simply enables the self test facility within the modem control register

►STOn()
►SelfTest()
►SelfTestOn() (Page 127)
►Non of these

Question No: 16 ( Marks: 1 ) - Please choose one

DCE is _____________

►Data communication equipment (Page 109) rep

►Dual communication equipment
►Data clearing equipment
► None of given

Question No: 17 ( Marks: 1 ) - Please choose one

REGS is a Union

►True
►False

Question No: 18 ( Marks: 1 ) - Please choose one

In self test mode the output of the UART is routed to its input

►True (Page 117) rep

►False

19

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
 CS609 System Programming
Mid Term Examination

Question No. 1 Marks : 2

If CPUID instruction is not present then the processor can be a

► 486 processor (Page 166)

► 386 processor
► 286 processor
► All of the above

Question No. 2 Marks : 2

On the execution of IRET instruction, number of bytes popped from stack is

► 4 bytes
► 6 bytes
► 8 bytes Click here for detail
► 10 bytes

Question No. 3 Marks : 2

Keyboard Status Byte is located at the address

► 0040:0000H
► 0040:0013H
► 0040:0015H
► 0040:0017H (Page 29)
Question No. 4 Marks : 2
If we use keep (0, 1000) in a TSR program, the memory allocated to it is

► 64000 bytes
► 32000 bytes
► 16000 bytes
► 80000 bytes

Question No. 5 Marks : 2

Maximum number of interrupts in a standard PC is

► 64
► 128
► 256 (Page 10)
► 512

20

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
 CS609 – Solved Quizzes (1 & 2)
Quiz No.1
Question : 1 of 10 ( Marks: 1 ) - Please choose one
Total No. of bytes that can be stored in Keyboard Buffer is____.

►16
►32 (Page 54)
►64
►128

Question : 2 of 10 ( Marks: 1 ) - Please choose one

If printer is _____ then printer sends back the ACK signal to the printer interface

►idle (Page 97)

►busy
►Out of paper
►None of the given

Question : 3 of 10 ( Marks: 1 ) - Please choose one

The baud rate is set in accordance with the divisor value loaded within the UART internal registers base +0 and
base +1.

►TRUE (Page 114)

►FALSE

Question : 4 of 10 ( Marks: 1 ) - Please choose one

Int 14H __________ can be used to receive a byte.

►Service # 0
►Service # 1
► Service # 2 (Page 121)
►None of the given options

Question : 5 of 10 ( Marks: 1 ) - Please choose one

The BIOS interrupt 0x1AH can be used to configure real time clock

►True (Page 136)

►False

21

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question : 6 of 10 ( Marks: 1 ) - Please choose one
------------ is used to read date from RTC

►1A\02H
►1A\03H
►1A\04H (Page 138)
►1A\05H

Question : 7 of 10 ( Marks: 1 ) - Please choose one

The -------- function receive a byte and COM port number is passed as parameter using BIOS service

►Receivebyte ();
►Receive ();
►Receivechar (); (Page 125)
►None of the given option

Question : 8 of 10 ( Marks: 1 ) - Please choose one

------------ whenever receive indicates the start of communication ……….. whenever receive indicates the end
of communication

►XON\XOFF (Page 135)

►XOFF\XON
►XON\YOFF
►YON\XOFF

Question : 9 of 10 ( Marks: 1 ) - Please choose one

------------ is used to read time from RTC
►1A\02H (Page 137)
►1A\03H
►1A\04H
►1A\05H

Question : 10 of 10 ( Marks: 1 ) - Please choose one

------------ is used to set time from RTC

►1A\02H
►1A\03H (Page 138)
►1A\04H
►1A\05H

22

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
 Quiz No.2
Question : 1 of 10 ( Marks: 1 ) - Please choose one
Software based flow control make use of -------- control characters

►Xon
►XOFF
►Both (Page 135)
►None

Question : 2 of 10 ( Marks: 1 ) - Please choose one

What will be the value of DL register when we are accessing C drive using undocumented service 21H/32H?

►0
►1
►2
►3 (Page 249)

Question : 3 of 10 ( Marks: 1 ) - Please choose one

Set the Interrupt vector means to change the double word sized interrupt vector within IVT.
►True (Page 22)
►False

Question : 4 of 10 ( Marks: 1 ) - Please choose one

If keyboard buffer is empty the head and tail points at the same location.
►True (Page 55)
►False

Question : 5 of 10 ( Marks: 1 ) - Please choose one

Standard PC can have _____ PPI.
►1
►4 (Page 84)
►8
►16

Question : 6 of 10 ( Marks: 1 ) - Please choose one

By cascading two DMAs ____ bits can be transferred.
►4
►8
►16 (Page 186)
►32

23

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question : 7 of 10 ( Marks: 1 ) - Please choose one
PPI interconnection _______ bits is cleared to indicate low nibble is being sent.

►D1
►D2
► D3
► D4 (Page 101)

Question : 8 of 10 ( Marks: 1 ) - Please choose one

File can be______ viewed as collection of clusters or blocks.

►Physically (Page 256)

►Logically
►Both physically and logically
►None

Question : 9 of 10 ( Marks: 1 ) - Please choose one

Operating system name contains ____ bytes in boot block.

►3
►5
►8 (Page 257)
►11

Question : 10 of 10 ( Marks: 1 ) - Please choose one

File system used in CD’s is_______ file system

►Contiguous http://www.pgallert.de/english/SysAdmin/OS/file.htm
►Chained
►Indexed
►None

Question : 1 of 10 ( Marks: 1 ) - Please choose one

________means typematic rate will be sent in next byte.

►0xF3 (Page 180)

►0xF4
►0xF5
►0xF6

24

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question : 2 of 10 ( Marks: 1 ) - Please choose one
To access the block within cluster using BIOS services the cluster number should be converted into _____.

►CHS
►LBA
►LSN (Page 258)
►None of the given

Question : 3 of 10 ( Marks: 1 ) - Please choose one

Display device (Monitor) performs _________ I/O.

►memory mapped (Page 30)

►Isolated
►Both of above
►None of these

Question : 4 of 10 ( Marks: 1 ) - Please choose one

Timer interrupt occurs _______ times every second by means of hardware.

►18.2 (Page 28)

►16.2
►15.2
►14.2

Question : 5 of 10 ( Marks: 1 ) - Please choose one

An I/O device cannot be directly connected to the busses so controller is placed between CPU and I/O.

►True (Page 83)

►False

Question : 6 of 10 ( Marks: 1 ) - Please choose one

Keyboard uses port ____ as status port.
►64H (Page 177)
►66H
►67H
►69H

Question : 7 of 10 ( Marks: 1 ) - Please choose one

Tail of keyboard should get to get the start of buffer.
►True (Page 55)
►False

25

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question : 4 of 10 ( Marks: 1 ) - Please choose one
Control information in files is maintained using

►BPB
►DPB
►FCB (Page 256)
►FPB

Question : 5 of 10 ( Marks: 1 ) - Please choose one

____ No. of bytes are used to store the character in the keyboard buffer.

►1
►2 (Page 54)
►4
►8

Question : 6 of 10 ( Marks: 1 ) - Please choose one

The ______ service # is not used in any interrupt.

►01
►02
►03
►FF

Question : 7 of 10 ( Marks: 1 ) - Please choose one

At IRQ 7 Interrupt # ___ is used.

► 0x0A
►0x0B
► 0x0C
►0x0F (Page 95)

Question : 8 of 10 ( Marks: 1 ) - Please choose one

We have set the bit No. 7 of IMR(Interrupt Mask Register) to unmask the Interrupt so that interrupt _____ can
occur at ____ line.

►0xf ,IRQ 7
► 0xa, IRQ 6
► 0x8, IRQ 5
►0x6, IRQ 2

26

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan
Question : 9 of 10 ( Marks: 1 ) - Please choose one
If we want to produce the grave voice from speaker phone then we have to load the ____ divisor values at Port
____.
►high, 0x42
►low, 0x22
►high, 0x22
►low, 0x42

Question : 10 of 10 ( Marks: 1 ) - Please choose one

In order to produce the sound from PC internal Speaker we have to load the___bit divisor value at the ___port.
►8, 0x21
►16, 0x42
►32, 0x22
►64, 0x32

Question : 1 of 10 ( Marks: 1 ) - Please choose one

In counter register bit no. 3 changes its value between 0 and 1 with in ____clock cycles
►1
►2
►4
► 16 (Page 69)

Question : 2 of 10 ( Marks: 1 ) - Please choose one

In keyboard status byte bit no. 2 and 3 are used for ctrl and alt keys respectively. which of the following
condition is used to check that Ctrl + Alt keys are pressed. Where: unsigned char far * scr = (unsigned char far
*)(0x00400017);

►if (((*scr)&12)==12)
►if (((*scr)&8)==8)
►if (((*scr)&4)==4)
►if (((*scr)&2)==2)

27

https://genrica.com https://youtube.com/c/VirtualUniversityPakistan