Scribd
Upload
45 views

2023 PROSOP-006 Operation - & - Cleaning of Grinding Machine

This document provides a procedure for operating and cleaning a grinding machine. It describes plugging the machine into a power source, loading materials, and switching it on to start grinding. After use, the machine should be unplugged and materials sealed. For cleaning, excess powder is vacuumed, surfaces are wiped with cleaning solution and rinsed with water. Parts are scrubbed, rinsed until suds-free, dried and reassembled before being disinfected with 70% ethyl alcohol and labeled as clean.

Uploaded by

colinvelasco
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
45 views

2023 PROSOP-006 Operation - & - Cleaning of Grinding Machine

This document provides a procedure for operating and cleaning a grinding machine. It describes plugging the machine into a power source, loading materials, and switching it on to start grinding. After use, the machine should be unplugged and materials sealed. For cleaning, excess powder is vacuumed, surfaces are wiped with cleaning solution and rinsed with water. Parts are scrubbed, rinsed until suds-free, dried and reassembled before being disinfected with 70% ethyl alcohol and labeled as clean.

Uploaded by

colinvelasco
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

DOC NO.

: BSPROSOP-11

REV NO.: 00

DEPARTMENT: PRODUCTION PAGE NO.: Page 1 of 2


EFFECTIVITY
TITLE: OPERATION AND CLEANING OF 01 May 2023
DATE:
GRINDING MACHINE

PROCEDURE

1. Purpose : This procedure describes operation and cleaning of grinding machine.

2. Scope : Grinding machine

3. Responsibility:
Operator  Compliance to the procedure
Production Head  Implementation of this procedure

4. Materials/Equipment to be used: Cleaning solution


Disinfectant Solution: 70 % Alcohol
Water
Lint free cloth
Dilution of cleaning agent
Name of cleaning agent Concentration Volume of Liquid cleaning Volume of diluent (tap
agent water)

Liquid cleaning agent-unscented 2% 20 mL 1000 mL

Dilution of disinfectant
Name of disinfectant Concentration Volume of disinfectant Volume of diluent
(deiozed water)
Ethyl alcohol 70 % 736.80 mL 263.20 mL

5. Frequency of Cleaning: After each use


Before Use, if equipment was left idle for more than 1 month.

6. Procedure:

6.1 Operation

PREPARED BY: NOTED BY: APPROVED BY

Mr. Colin Nathaniel Velasco Ms. Elinor Roquel Mr. Patrick Roquel
QC/QA Administrative and HR Manager General Manager
DOC NO.: BSPROSOP-11

REV NO.: 00

DEPARTMENT: PRODUCTION PAGE NO.: Page 2 of 2


EFFECTIVITY
TITLE: OPERATION AND CLEANING OF 01 May 2023
DATE:
GRINDING MACHINE

6.1.1 Plug the machine to a 220 v power supply source.

6.1.2 Ensure that the machine is clean.

6.1.3 With the sieve installed and a polybag in a drum underneath the hopper, pour the
materials into the hopper. Switch “on” to start the operation.
Note: Do not load too much material into the hopper to avoid too much pressure
on the sieve.
Caution: Avoid touching the moving parts of the machine during operation

Load the dried material into the grinder. Install the cover and lock tightly after loading
the product.

PREPARED BY: NOTED BY: APPROVED BY

Mr. Colin Nathaniel Velasco Ms. Elinor Roquel Mr. Patrick Roquel
QC/QA Administrative and HR Manager General Manager
DOC NO.: BSPROSOP-11

REV NO.: 00

DEPARTMENT: PRODUCTION PAGE NO.: Page 3 of 2


EFFECTIVITY
TITLE: OPERATION AND CLEANING OF 01 May 2023
DATE:
GRINDING MACHINE

6.1.4 After use, seal the material/product tightly.


6.1.5 Switch “off” and unplug from power source.
6.2 Cleaning

6.2.1 Unplug the machine from power source.


6.2.2 Vacuum excess powder from the product contact parts and exteriors of the grinder.
6.2.2. Wipe the exteriors with lint free cloth soaked in cleaning solution, wipe again with wet
cloth.
6.2.3 Detach the sieve, rinse the hopper, roller barrel and sieve with tap water until powder
is removed.
6.2.4 Scrub with lint free cloth or sponge soaked in cleaning solution.
6.2.5 Rinse with tap water until free of suds, finally rinse with 10 L of tap water. Let it dry and
re-assemble.
6.2.6 Cover or wrap the product contact parts with plastic.
6.2.7 Disinfect the product contact parts with 70% ethyl alcohol solution after cleaning and
prior to use.
6.2.8 Label the equipment with “Clean tag, PF-002” .
6.29 Have the equipment checked by Area In Charge or Department Head or QA.

PREPARED BY: NOTED BY: APPROVED BY

Mr. Colin Nathaniel Velasco Ms. Elinor Roquel Mr. Patrick Roquel
QC/QA Administrative and HR Manager General Manager

You might also like