General

Build
Guide
Your first stop
for build info

Contents of this document are ©2023 Pedal Parts Ltd.

No reproduction permitted without the express written
permission of Pedal Parts Ltd. All rights reserved. Rev 1.0
June 2023
CONTENTS
03 What’s this all about? 31 TESTING

32 Why test?

04 THE BASICS 33 Simple test rig

05 Introduction 34 Test wiring
06 Tools

07 Preparation 35 FINAL ASSEMBLY

08 Components 36 Assembly order

09 Resistors 39 LED

10 Resistor Colour Codes

11 Capacitors 40 BYPASS WIRING

12 Capacitor Codes 41 Introduction

13 Diodes 42 3PDT - Original

14 Transistors 44 3PDT - Compact

15 Integrated Circuits (ICs) 46 3PDT - Top LED

16 Potentiometers 48 DPDT - OptoPuss

17 Trimmers (Presets) 51 Other variations

18 Toggle Switches 52 Top-mounted DC socket

19 Rotary Switches 53 Top-mounted DC socket and jacks

20 LEDs 54 Positive ground wiring

21 Jack Sockets

22 DC Sockets

23 Footswitches

25 GENERAL BUILD GUIDELINES

26 Introduction
These contents are clickable
27 Parts and layout conventions
- no need to scroll around.
28 Holding parts in place

29 Placing pots and switches

Click the link in the top left
30 Ribbon connectors
of any page to return here.
<
WHAT’S THIS ALL ABOUT?
We’ll give you some basic information about what all those bits and pieces are in front of you,
the best way to populate the PCBs, and how to do the final assembly.

Hopefully you’ll have a lovely working pedal at the end of it.

There are four distinct sections:

• The Basics
This was originally a separate document altogether, but no harm having
it here. You can easily jump past this if you know what’s what. This will
give an outline of the different components, including connectors and
switches.

• General build guidelines

Directions on the best way to approach getting all those parts soldered
onto the PCB.

• Testing
In almost every case it’s best to test the main circuit board before
connecting up the offboard elements.

• Bypass and final assembly

Instructions for the different bypass methods we offer and how to
connect everything together once the circuit is complete.

Some of the above - particularly the last two sections - may not be relevant to your kit. In these
cases the individual documents for those kits will be more comprehensive than those that follow
these guidelines. You won’t be left hanging.

Some of the images used in this document are from the excellent
Pedal Builders Vector Pack from On the Road Effects.

INTRO 3
<

THE BASICS
What’s that stripe? Why does that hurt?

4
<
What’s in this section?
The basic information you’ll need to recognise a component, read its value
and find where to put it on a PCB.

What is it not?
A technical document or an indepth explanation of the ins, outs, whys and wherefores of
all things electronic. There are many online resources which will give you as much
information as you need about components, schematics, electricity, soldering
techniques etc. They’ll explain it far better than we could, so go out and learn if you want
to do more than put your nice new kit together.

There’s a lot of text...

Sorry, but that’s entirely necessary. You’ll only need to read it through once, maybe twice.

Hopefully by the end of it

you’ll have gone from a
bag of bits to a finished pedal.

THE BASICS > INTRO 5

<
TOOLS
There’s a bare minimum you should have in
your arsenal if you’re going to get through
this. Sure, you can probably get away with
trying to clip component legs with kitchen
scissors, but you’re going to get sick of it.

Soldering Iron / Solder

You want something with a fine tip, not a
massive plumber’s spade tip. Soldering
stations are easier to work with, but a simple
iron with an in-line power cord will be fine,
though you will need a stand with cleaning
sponge. Then ditch the sponge.
Get some brass wool tip cleaner and stick Heat Sinks
it where the sponge used to be. Fine solder is Anything metal that will grip onto something
best for small work like this - 0.7-1mm. on its own. Crocodile clips will do it.
Self-closing tweezers are great.
Wire Strippers / Cutters
Separate or combined. Stripping wires with a Multi Meter
Stanley knife is tedious and gives you grey The best £20 you’ll ever spend. Again,
hair much sooner than is necessary. budget-dependent, but even the cheaper end
of things will do most of what you need.
Pliers
Fine needle-nose will serve you well. Screwdrivers / Spanners / Hex Keys
You know, just general tools. A set of
Desolder Pump and Solder Wick precision screwdrivers will serve you well.
You WILL put something in the wrong place There are a few spanner sizes that you’ll
and have to remove it. These will help. repeatedly use when assembling - 14mm,
Fluxed wick is well worth the extra cost. 12mm, 10mm for sure. You could take the
really sensible route and get a set of
Helping Hands
Pepers’ Pedals Rocket Sockets - a specially
Moveable arms with crocodile clips to hold
designed tightening tool set that won’t
your work. Handy. There are loads to choose
scratch your enclosure.
from, so go with what your budget allows.

A NOTE ON STATIC
Some components are very sensitive to
static, so you should take precautions to
ensure you aren’t going to damage them.
We wouldn’t expect someone starting out UN
LIK
to invest in specialist items to do this, so EL
Y
please do a search on ‘ESD protection’.
It can be as simple as touching something
metal before handling items.

THE BASICS > TOOLS 6

<
PREPARE THYSELF...
Soldering your first PCB
Don’t.
If you haven’t soldered before, please do a bit of practice first.
Get hold of some strip board (also known as vero board),
watch some How-To videos and practice on that.

Lesson 1
Soldering irons are hot. Solder gets hot. Everything a soldering iron touches gets hot.
Your hands don’t like it, and neither do the components you’ll be soldering.

Sure, some will complain less than others, but the basic rule is - only apply heat for as
long as necessary.

Learn which components are more resilient than others, and take the right precautions
where needed.

Lesson 2
Electricity kills. If you’re reading this you probably
don’t know nearly enough to go anywhere near mains
power. Stick to batteries and 9V power supplies, and
then only use the latter when you’ve tested your
circuit with the former.

OK, I’m ready

Cool. Now you need to learn how to recognise what that bewildering pile of components is and
where they go. Read on...

THE BASICS > PREPARATION 7

<
COMPONENTS
You won’t get an explanation of
what components actually do in
this document. Again, there are
many resources that will do that
far better than we could.

This document deals entirely with

through-hole components. That is,
components with bits sticking out
that will go through holes on a
PCB. Surface mount is a whole
different ball game.

Hopefully the following pages will have you recognising components with ease.

Seriously - invest in Electronics for Dummies and read it cover to cover. Twice.
Then go back and read the bits you weren’t sure of for a third time.

You don’t need to know how electrons move to build a fuzz box, but it sure is fascinating.

Recognising the parts on your PCB

RESISTOR TRANSISTOR

DIODE

TRANSISTOR
DIODE

BOX OR CERAMIC CAPACITOR

TRIMMER
ELECTROLYTIC CAPACITOR

POT

THE BASICS > COMPONENTS 8

<
RESISTORS Heat tolerance: HIGH

There are lots of different looking ones around, but for the most part you’ll deal with two kinds that
look very similar.

Most resistors supplied with our kits are rated at 0.25W (quarter watt) which is more than
adequate for the power they need to handle.

They’ll be made of either Carbon Film (usually beige/yellowish case) or Metal Film (blue case).
They do the same job, they’re just made of different stuff and have different tolerances. In most kits
these parts will be around 6mm in length. Some kits have smaller 3mm resistors which are fiddly
to handle but do the same job in a tighter space..

Carbon film resistors normally have quite a high tolerance - around 5%, meaning a 100K resistor
may measure anywhere between 95-105K. This is fine in a lot of cases, but sometimes something
more precise is required.

Metal Film resistors are normally 1% tolerance, even 0.1% if you want to spend a lot of money, but
that kind of precision simply isn’t required here.

So, you recognise resistors...

Now, which is which?

They’re just full of stripes!

THE BASICS > COMPONENTS > RESISTORS 9

<
RESISTOR COLOUR CODES
You can learn how to read these, or just Google ‘Resistor Code Calculator’, select your colours and
it’ll show you the value. Or you can set your newly purchased multimeter to Resistance and just
measure the value by placing your probes on each leg. Or learn how to read them - here you go:

Resistors are measured in ohms, and the codes are shown as multiples of 1 ohm.

Each stripe represents a number:

0 BLACK 5 GREEN
The tolerance band shows you the %
1 BROWN 6 BLUE
margin of possible variation in the shown
2 RED 7 VIOLET
value. There are a few of these, but you’ll
3 ORANGE 8 GREY
mostly come across Silver (10%), Gold (5%),
4 YELLOW 9 WHITE
Brown (1%)

4-BAND 5-BAND

1st Digit 2nd Digit Multiplier Tolerance 1st Digit 2nd Digit 3rd Digit Multiplier Tolerance

The first two bands of this resistor give you The first three bands of this resistor give you
two digits. In this case 2 and O. three digits. In this case 3, 9 and 0.

The third band gives you the multiplier, which The fourth band gives you the multiplier, in this
is the number of zeros to add after the first case 4.
two digits, in this case 1.
The resistor above measures 390 followed by 4
The resistor above measures 200 ohms. zeros. That makes it 3,900,000, or 3900K, so
3.9M (also written as 3M9).

It would be a bit much having to write out

75,000 ohm and such, so we dont:
This one is:
1000 ohm = 1K (1 Kilohm)
5, 6 and 2, which is 56 followed by 2 zeros, so
5600 ohms, or 5.6K (or 5K6). 1000K = 1M (1 Megaohm)

Resistor values under 1K will often be written as the value followed by R. Resistance, get it?

So you may see a 100 ohm resistor written as 100R.

THE BASICS > COMPONENTS > RESISTORS 10

<
CAPACITORS Heat tolerance: MEDIUM

There are many different shapes and sizes of capacitors, or ‘caps’ out there, made from lots of
different materials, but they’ll generally fit into two distinct categories.

POLARISED means that the capacitor has a NON-POLARISED means there isn’t a positive
positive (+) side and a negative (-) side. or negative leg. Non-polarised caps can go
In essense that means that in a circuit a into the circuit either way round.
polarised cap has to go in a certain way.
The caps below are all different shapes, sizes
The positive leg will normally be longer than and materials, but they’re all non-polar and,
the negative. There’ll usually also be some believe it or not, all have exactly the same
kind of marking on the case to indicate which value. If placed in a circuit they’ll all do exactly
is which. In the image below the white stripe the same job, though different materials can
on the middle cap indicates the negative lead. have an effect on the sound of a circuit. Most
The small yellow cap is made of Tantalum, and of the non-polar caps that come with our kits
the positive leg is indicated by a +. are either polybox type (like the small cream
one, though they can be many other colours),
or ceramic like the small brown disc.

100n? 10u? 100p? What the....?

Capacitance is measured in Farads.
A Farad is huge. You will not be coming across any caps with whole Farad measurements until you
start building fuzz boxes based on tesla coils and military laser systems. We’ll be dealing with tiny
fractions of Farads - microfarads (uf or, if you want to be pedantic, μf), nanofarads (nf) and
picofarads (pf). Everything is based on multiples of 1000 so they aren’t too hard to remember.

THE BASICS > COMPONENTS > CAPACITORS 11

<
RECOGNISING CAPACITOR VALUES
Most caps you come across will have their value shown in uf, nf or pf.

1uf = 1,000nf = 1,000,000pf

0.1uf = 100nf = 100,000pf
0.01uf = 10nf = 10,000pf
See where that’s going? Obviously there are circumstances where one unit of measurement is
going to be more appropriate than another, and manufacturers tend to use their common sense.
You wouldn’t label a 1uf cap as 1,000,000pf now would you?

That being said, sometimes they don’t make as much sense as you’d like.

POLY BOX CAPS CERAMIC CAPS

These will be marked in one of two ways, These tend to be used for lower values (though
either in nf or uf. It will be easy to tell which. not always), and are measured in pf. The
Different manufacturers follow different rules, markings take the format of three digits, and
but generally the following will apply. similar to resistors they are:

Caps between 1n and 100n will normally be Digit Digit Multiplier

shown as the actual value followed by an n,
so for instance, 10n. So a cap marked as 101 would be 10 with one
trailing zero, which would be 100pf.
Over 100n and it can get trickier. They may be
shown with their actual nf value, but often they 223 would be 22 with three zeros - so 22,000pf,
are marked in uf. In this case it will be shown which is 22nf.
as a decimal fraction, such as .22, and won’t
We won’t normally supply ceramic caps for
be followed by a letter.
values above 1nf.
In this case, the cap value is 0.22uf, which, in
nf, is 220n. As there are 1000 nf in 1 uf, simply
put three zeros after the uf value shown.
0.22 followed by three zeros is 220.

There are other markings on there which

indicate tolerance and voltage rating.
Don’t worry about them. .1J63 indicates a 100n
cap with 5% tolerance (J) and rated to handle
63 volts. Everything supplied in the kits is well
within necessary tolerances and voltage
ratings. Only concern yourself with the values.

Hopefully the whole x1000 thing is making a little sense by now..?

THE BASICS > COMPONENTS > CAPACITORS 12

<
DIODES Heat tolerance: VERY LOW

Once again, these vary greatly in size

and appearance. This electronics thing
isn’t as straight forward as you were
expecting, eh?

Though they look fairly different, diodes

will normally follow one format - a
barrel with a leg sticking out of each
end, one leg being positive (anode), one
negative (cathode).

In most cases you’ll find the cathode

end is indicated by one or more
stripes, and in most cases this leg will
go to a square pad on the PCB.

In MOST cases, but....

Say hello to our Russian friends. These follow their own rules, and will usually have stripes
indicating the anode. Helpful, no?

As with all components you should treat diodes with care, especially when bending the legs.
The points where they meet the glass casing are easily cracked, especially on the large DO-7 style
cases of the 1N34A or Russian germaniums. The best way to approach them is to grab the leg right
up against the body with your smallest needle-nosed pliers and bend the leg with your finger,
letting the pliers take the strain away from the casing.

Diodes have many purposes in the circuits we’re dealing with. This document is about identifying
them, not psychoanalysing them.

One thing diodes do have in common is their dislike of excessive heat.

CAREFUL!
THE BASICS > COMPONENTS > DIODES 13
<
TRANSISTORS Heat tolerance: VERY LOW

Do we really need to keep repeating the fact that most

components come in many different forms? Thought not.

Transistors are perhaps the most varied though, and probably

the parts that’ll cause you the most heartache. They’re very easy
to fry with excessive heat, especially FETs and MOSFETS such
as 2N5457 or BS170. Take your time with them.

They are also sensitive to static (especially FETs and MOSFETS),

so make sure you’re suitably discharged before handling them,
and leave at least ten seconds between soldering each leg.

You’ll mostly deal with two different classes of transistors

in stomps.

BJT - Bi Junction Transistor

FET - Field Effect Transistor
You’ll be dealing with three legs pretty much all the time. There are transistors with more, but we’re
not getting too exotic right now.

BJTs consist of: FETs consist of:

Collector Base Emitter Drain Gate Source
On older style metal hat casings the Again, looking at the case is no help
emitter is normally identified by a small whatsoever. Check the build document or
metal tag, and the collector leg will often be datasheet for more info on each type as the
shorter than the others. On the most pin-out - the order the legs are in - will
common, more modern TO-92 black plastic differ between models.
casings we aren’t so lucky.

They can be arranged pretty much any

which way, and it’s a case of checking with Once again, Russian stuff plays by its own
an online datasheet or using a component rules. Tester or datasheet required, though
tester to identify which is which. we’ll always mark the legs on any we
supply in kits.
Fortunately PCBs are usually designed with
specific transistors in mind. Certainly any There are others transistor types, such as
FuzzDog PCB you come across will show the Uni Junction Transistor (UJT) found in
the transistor outline on the PCB exactly as the Repeat Percussion, but we could fill a
it should be placed, or there’ll be an whole document with them.
explanation of any deviation in the build
Sometimes you’ll find an IC in a transistor-
document.
style case, i.e. voltage regulator 78L05.

THE BASICS > COMPONENTS > TRANSISTORS 14

<
INTEGRATED CIRCUITS Heat tolerance: VERY LOW

...or ICs, or chips. Little (usually) black packages of goodness, containing many tiny components.
One part to do the job of many. We recommend you always use a socket for these parts.

Once again, this is purely about identification and orientation/placement.

You’ll normally come across a black case with two rows of legs, like a lovely robotic insect from the
future. These are known as Dual InLine (DIL) packages. Occasionally you may have to deal with a
single row of legs, which are Single InLine packages (SIL), but these are less common.

You need to know which way round they go, and which leg is which. If you put them in the wrong
way and power up, chances are it’s goodnight IC. Hope you have a spare.

The silkscreen legend on our PCBs will have a notch at one end of the IC. This indicates the top.
The pin to the left of that notch is always pin 1. Sometimes an IC won’t have a notch, but will have a
small dot printed on the top of the case instead. This indicates pin 1.

From pin 1 you count down the package, then back up the other side to find your leg numbers.

Dimple
Dot

Pin 1 Pin 1 Pin 14

Pin 4 Pin 4
Pin 5

Sockets will save you Pin 7 Pin 8

a world of pain >>>

HEAT AND STATIC ALERT!

ICs don’t like either. Handle with care, ground yourself before picking them up, and use
sockets instead of soldering them direct to the PCB where possible.

....and CONFUSION ALERT - the 78L05 voltage regular mentioned on the last page is actually
an IC in a transistor package. Don’t worry about it.

THE BASICS > COMPONENTS > INTEGRATED CIRCUITS 15

<
POTENTIOMETERS Heat tolerance: MEDIUM

The fun part. These, along with switches, are likely your only point of interaction with a finished
circuit, so get them right.

They’ll either mount straight into the PCB or will be wired. The important thing to get right is the
leg numbering.

They look like tough cookies, but guess

what? Beneath that tough exterior they
have delicate souls.

The variable resistance they produce is

normally via a thin wafer of carbon that is
easily damaged by too much heat on the
pins. Careful now.

As well as a value, pots are marked with a

code to indicate their taper. What’s taper? PIN 1 PIN 3
It’s the way in which the pot changes the
resistance when turned.

A = Logarithmic (also sometimes known as Audio)

The resistance changes slowly at the start of the turn from fully
counter-clockwise, but gets increasingly quicker towards the end
of the turn.

B = Linear
Change in resistance is the same throughout the turn.

C = Anti-Logarithmic / Reverse Logarithmic

Changes quickly at first but slows down towards the end of the turn.

W = A combination taper sometimes called ‘Tone’ taper.

Not so common, but seen in Tube Screamer type circuits.
Kind of does its own thing.

Just to complicate things a little you may also come across DUAL-GANG pots. These have two rows
of pins - so six in total, and are essentially two pots in one. They enable control of two different
elements of a circuit with one knob. The two sets of resistances are almost always of the same
value, i.e. a 100KB dual-gang. If you ever come across a circuit that requires a dual-gang with two
different values, move on. That’s a world of pain, and thankfully very rare.

THE BASICS > COMPONENTS > POTENTIOMETERS 16

<
TRIMMERS (or presets) Heat tolerance: MEDIUM

The potentiometer’s shy cousin. These are normally used for set-and-forget adjustments such as
transistor biasing. If you want to get really tweaky you can normally replace a trimmer with an
external pot, but more often than not there’s a good reason that control has been left inside.

These come in lots of shapes and sizes, as well as having different operational characteristics.
Some, such as lefty and centre up there, cover their entire resistance range in one single turn.
Others, such as righty, will require many turns - usually 13 or 25 - to get from one end to the other.
Easy does it. In both cases it can be quite easy to force the turn too far and snap the mechanism,
especially with the multiturns. Adjust these very slowly and delicately - you’ll feel a slight
resistance to the turn when they reach the end of the range. Don’t push it.

On most boards we’ve produced since

around 2018 the PCB footprint for trimmers
has multiple pads to allow for different formats.

The pads are connected within the copper

traces of the PCB as shown. As long as you
have one leg of your trimmer in each column
of pads you’re good to go.

THE BASICS > COMPONENTS > TRIMMERS 17

<
TOGGLE SWITCHES Heat tolerance: HIGH

These come in lots of different shapes, sizes and configurations.

You shouldn’t have to worry about that, as we’ll provide

whatever is required, or list them with enough
info to help you source the correct unit.

You’ll find them described by the number of poles

and the type of throw they have. Say what?

OK, a switch with one column of lugs will be described

as single-pole.

Two columns will be double-pole. Three columns... you get the idea.

This is followed by the throw - single or double. That’s usually all we’ll be dealing with, so no need
to get overly complicated here.

One more thing - the way they switch between those sets of poles. Maybe the switch has two
positions, switching from one sets of poles (ON) to the other (ON), which would be described as
ON-ON. If stops in the middle, where the centre pole connects to neither of the outer poles, so
totally off. This would be ON-OFF-ON. Simple, right?

You’d think so. We also deal with another type - ON-ON-ON - whereby in the centre position two
opposite sets of poles are connected. OK, brain freeze. It’ll be easier with illustrations - these show
the lugs on the bottom of the switch.

Below we have a DPDT ON-ON switch (double pole, double throw, two position).

The first simply shows the 6 poles - two sets of three. Centre pic shows which lugs are connected
when the switch is in the down position - the connection will always be the opposite side to that
which the switch is pointing in. The third pic shows the connections with the switch up. With an
ON-ON switch the centre two lugs will always be connected to one or the other sets of outer poles.
For an ON-OFF-ON, with the switch in the middle position the centre lugs aren’t connected to
either of the outer sets.

We’ll touch on ON-ON-ON (far right pic). In the centre position the lugs are connected as shown.
There are two types though, one connects as here, the other the opposite way. Phew!

Don’t sweat the ON-ON-ON -

where this is used the
complicated bits are dealt
with in the PCB design.

THE BASICS > COMPONENTS > TOGGLE SWITCHES 18

<
ROTARY SWITCHES Heat tolerance: MEDIUM

Sometimes you need more than the two or three options offered by a simple toggle, no matter how
many poles you cram on there. In this case we can turn to the rotary.

Once again, these come in lots of different We may wish to switch three different
configurations depending on the number of elements of the circuit, but only want three
poles and throws required. different variations. We’d still need three poles,
but you’d only use three of the four throws.
For instance, if you needed one part of your
circuit to have twelve different switchable These often have long
options, you could use a 1P12T (one pole, shafts, so will require
twelve throw) switch. Perhaps you want to some hacksaw action to
change two things in the circuit, and have six shorten them.
different options of each - 2P6T. And so on, for
3P4T (three poles, four throws) and 4P3T (four
poles, three throws).

Here’s a 3P4T, which is what we mostly use.

Notice the locator lug - where there is a space
on one of our PCBs for one of these switches
there’s a circle with a cross inside to indicate
the correct postion for this.

The washer under the nut has a lug

on it. This can be located in one of the holes
around the body of the switch to limit the
number of positions it can be turned.

Here’s a view from below of a 3PDT rotary. It shows the central three poles connecting to each of
the corresponding outer poles as the switch is rotated through its four positions:

1 2 3 4

THE BASICS > COMPONENTS > ROTARY SWITCHES 19

<
LEDs Heat tolerance: VERY LOW

Shh. Be very quiet. These little fellas are

incredibly delicate. And difficult to clearly
photograph, so...
The image to the left is a single colour LED.
ANODE There are others, but you’ll rarely come across
them in our kits. Just for clarity, here’s
examples of others that we supply with a small
amount of kits.
CATHODE
Bi-colour LED will display two different
colours depending on which side of the device
is powered. These come in two different types
LEDs are diodes that light up when current
- common anode and common cathode.
flows through them. It’s that simple.

The ANODE (+) leg will always be longer than

the CATHODE (-) leg, so it’s easy enough to
identify which is which. Once those legs are
snipped, you can recognise the cathode by a
slightly flattened edge on the casing.

As well as being a handy indicator as to

whether your pedal is on or off, they can be
used to clip your signal, just like a regular
diode. So, with that in mind, don’t worry about
seeing them on circuit boards but not poking
out of the enclosure. They’re busy inside.

You need to take extra care when soldering

these fellas. A heat-sink of sorts is a must.
There’s no need to poke the legs all the way Common anode - the positive supply is always
through the board before soldering - feel free applied to the single anode. The negative
to leave the body a good distance away from supply will be applied to one cathode or the
the surface of the PCB. other, lighting up whichever colour is powered.
You can also supply both cathodes at once and
As with most other components, these come have a combination of both colours, but why?
in many shapes and sizes. We normally supply
3mm for your on-off indicator, but others Common cathode is the same but the other
within kits may be 5mm. way around, if that makes sense?

We highly recommend you avoid colour-cycling

LEDs which will constantly change colour
when powered. These can cause noise in your
circuit.

THE BASICS > COMPONENTS > LEDs 20

<
JACKS Heat tolerance: HIGH

The gateway in and out of your pedal. We deal almost entirely with 6.35mm (1/4”),
and use three particular types across our range.

OPEN FRAME TIP

The type used in most of our kits. We tend to stick with Neutrik as a
manufacturer as the quality is second to none. Beware cheap
immitations. SLEEVE

These come in two configurations: two-pole (mono) and three-pole RING

(Tip Ring Sleeve - sometimes referred to as stereo).

You’ll normally deal with mono unless you want battery provision in SLEEVE

your pedal, in which case the TRS jack is used as a nifty way to
disconnect the battery when the input jack is removed. TIP

TIP

RING

LUMBERG SLEEVE
Handy in a tight spot, and also great quality. TIP
Same deal as above regarding configs.

SLEEVE

THROUGH-HOLE SLEEVE TIP

There are lots of types of these, but we tend to stick to those shown.
Again, available mono and TRS. Where these are used on our PCBs
we normally include extra pads so TRS can be used even when
mono will suffice. These jacks have two sets of pins for each
TIP RING SLEEVE
connection, one set being switched. This switch is opened when the
jack is inserted. Don’t worry about it. Our PCBs have you covered.

THE BASICS > COMPONENTS > JACK SOCKETS 21

<
DC SOCKETS Heat tolerance: HIGH

You have the power!

Once again, three types across our kits.

All are 2.1mm barrel, normally wired with the tip negative.

BOSS-STYLE SWITCHED
SWITCHED/
Used on almost everything we supply. BATTERY +

POSITIVE
These can be wired as a simple +/- or in conjunction with
GROUND
a TRS jack you can use them to include a battery in your
pedal. There’s a switch mechanism which disconnects
the battery supply when a DC plug is inserted.

MINI
Used for tighter builds such as FuzzPups POSITIVE
(hey - that’s a whole different document),
GROUND
or for pedals with top-mounted DC and jacks.
These have only two pins. The longer pin is
normally for your positive connection unless
otherwise stated in an individual build doc.

GROUND

THROUGH-HOLE POSITIVE
A PCB-mounted jack used on a few of our kits, such as
tester units or buffers. It’s difficult to get a square hole
drilled into an enclosure, so these will normally sit inside
the box with a round hole offering access. SWITCHED/
BATTERY +

THE BASICS > COMPONENTS > DC SOCKETS 22

<
FOOTSWITCHES Heat tolerance: HIGH

Very important, as in most cases this is your main point of contact with your pedal.

We currently deal with two different types of these, one of which has two variants.

By far the most common type used is 3PDT (or three-pole, double throw). The actual mechanics of
these should be fairly clear from the description of the toggle switches.

We’ve been at this a long time, and have tried these switches from many different manufacturers.
We now have a standard 3PDT switch which we’re entirely confident in. This is the blue one.

We also offer a premium 3PDT from Gørva. This has a softer click than the standard switch and is,
in our opinion, worth the extra investment for a pedal you’re going to be stomping on a lot.

Our OptoPuss bypass system uses a DPDT switch, along with some clever circuitry to provide the
functionality of the 3PDT with one less pole. This has a much shorter throw - the distance the
switch travels before engaging - than the two 3PDT. It still has a definite ‘click’, somewhere in
between the other two.

Honestly, if you’re reading this section of

the document you’re probably new to this.
We’d recommend avoiding the OptoPuss bypass
as the optocoupler used in the circuit is incredibly
sensitive to heat, and very easily damaged.

THE BASICS > COMPONENTS > FOOTSWITCHES 23

<

Hopefully this spot of light reading will have set you

on your way to populating your PCB.

It’s by no means a comprehensive field guide for engineers,

but as a part-spotter’s guide it should see you right.

Here endeth The Basics

THE BASICS > COMPONENTS > CONCLUSION 24

<

GENERAL
BUILD
GUIDELINES
What to do... what not to do.

25
<
This isn’t paint by numbers
Sorry, no hand-holding here, just general tips on
putting the bits in the right place and getting your
pedal together.

1 Read your kit-specific build document from start to finish.

2 Separate out the parts, read the values and check against the bill of materials (BOM).

3 Contact us immediately if something is missing, incorrect, or you simply can’t identify it.

4 Decide which order to assemble the parts - usually height is a good indicator. It’s good
practice to start with the smallest and least susceptible to heat, i.e. resistors. Here’s our
recommended order:

Resistors
Diodes (flat)
IC sockets
Film box caps
Electrolytic caps
Diodes (vertical)
Transistors
LEDs

Of course this list will totally depend on the individual kit, and you’ll find your own way after
a few builds.

5 TEST! See later in this doc.

6 Fix.

Repeat steps 5-6 until everything sounds good. It’s entirely pointless boxing up a partially
working circuit then trying to troubleshoot.

7 Embelish your enclosure. Of course you can do this first, but we sometimes hear from people
who’ve spent forever making the box look sweet but just can’t get the circuit working. What a
waste of time and effort.

8 Box it up with the off-board bits in place.

9 Enjoy.

GENERAL BUILD GUIDELINES > OUTLINE 26

<
Putting parts on to (in to?) the PCB
Our PCBs have clear silkscreen part placement guides printed on them, including part numbers.
Follow this and you can’t really go wrong.

As mentioned on the previous page, READ THE KIT SPECIFIC BUILD DOCUMENT before you start.
Maybe we’ve messed up and mislabelled something.

General Layout Conventions

Unless otherwise stated in the build doc, these are universal across our PCBs:

Electrolytic capacitors:
Long leg (anode) to square pad. Stripe indicates cathode.

Diodes/LEDs:
Striped leg (cathode) to square pad. Short leg to square pad for LEDs.
The exception to this is with Russian germanium diodes - stripe = anode.

ICs:
Square pad indicates pin 1.

Making components fit

Resistors - you need to bend the legs, obviously.

Capacitors - most will drop straight into the holes in the space provided, though with ceramic caps
the legs may need to splay slightly.

Transistors - most will need the two outer pins to splay slightly, some will be pre-formed to fit.

Diodes - bend those legs. Do this VERY carefully with large-bodied (DO-7) germanium diodes.
The body will very easily break if you don’t offer some strain relief. Grip the leg with needle-nosed
pliers tight against the body and bend the leg with your finger, letting the pliers take the strain.
Sometimes diodes need to be placed vertically - just bend one leg 180° to be parallel with the other.

ICs - the legs need to be eased inwards slightly to fit into their sockets.

GENERAL BUILD GUIDELINES > PLACEMENT 27

<
Holding parts in place
We use two main methods for this. The tip and balance, and the leg bend.

We use a combination of both. Where there are a bunch of parts of the same height - i.e. resistors,
box caps etc - we use the first. Once you get onto electrolytic caps and transistors the latter is
definitely more practical.

Tip and balance

With your PCB in your helping hands, silkscreen side up, place your group of parts (i.e. resistors).
Leave the legs straight as shown left. Now take your enclosure lid, or any other hand flat, stiff
object, and hold it onto the parts to keep them held in place. Now flip the whole thing over so the
PCB is sitting on the lid. Boom! You can now solder everything in place, snip the legs and continue
with the next batch of parts.

Leg bend
Place your components one at a time and bend the legs out slightly against the pad so they can’t
fall back through. Done. Why don’t we just use this method for everything? We find the bent legs
can get in the way more when making your way through with the soldering iron. You could of course
just do a few parts at a time. Wish we’d thought of that...

GENERAL BUILD GUIDELINES > PLACEMENT 28

<
Pots and toggle switches
Almost always best to do these last. In a lot of cases, once you solder the pots in place you’ll have
covered up a lot of the underside of the PCB, restricting access to the pads. You can bend the pots
out of the way if you really need to, but you can only subject them to so much of that before the legs
give up and snap.

Getting pots straight t

Get the pot in place, solder one pin. Do a visual You really don’t want to be poking a hot
check to see that all three pins are all the way soldering iron into that tight space where the
into the PCB and the pot is straight. If not, bass and treble pot pins are, risking burning
melt that one joint and push the pot firmly into nearby components. Fortunately we’re dealing
the correct position. Once all three are snugly with double sided PCBs, so you can solder the
home you can solder in the remaining two. pots from either side of the board.

Now, sometimes the pot pins will be hard to In this case it’d be best to place the two rear
access once all the other parts are soldered in pots first, soldering on the same side as the
- see below. pots with unhindered access. Then you can
approach the front pair from either side.

Toggles T
You shouldn’t ever have to worry about Single pin first, melt, adjust with some
accessing the pins for these - there’ll always wiggling until you get it nice and straight, then
be plenty of space. Use the same method to commit the other pins.
get them straight as per the pots.

GENERAL BUILD GUIDELINES > POTS AND TOGGLES 29

<
Ribbon connectors
These aren’t necessary - four lengths of wire will do the same job - but they do make a neat finish.

Some people don’t like them as the joints where they meet the board can become brittle and snap
with repeated bending, but the same could be said of any wire.

On the majority of our kits these are 4-way, i.e. there are four individual wires in the ribbon.
Sometimes there are six or more, but individual kit documents will deal with that.

There’s really only two things to watch out for with these.

• Don’t try to make sharp bends. They will break internally. Keep your bends nicely curved.

• Determine which side of the PCB they’re going to go on before you break out the iron.
In some cases the ribbon will have to attach to the main component side of the board, in
others the pot side. You really don’t want to try to remove one of these once they’re attached.
They are difficult to strip if you need to shorten them, so it’s best to plan how they’re going to
sit in the enclosure to work out if you need to cut them or not.

Here the ribbon is on the same side as the In the case below there’s a pesky pot right
pots. It runs vertically straight down to the face where the ribbon would normally attach. Here
of the enclosure, has a gentle bend, runs we keep it on the component side of the PCB
below the jacks, another gentle bend and up to and solder it in before that pot. From here it
the underside of the daughtboard PCB. Nice. can arch over the top of the jacks and into the
If it was still a little long it could have bent top side of the daughterboard. No rules, just
back and gone under the main PCB a little. common sense and care.

GENERAL BUILD GUIDELINES > RIBBON CONNECTORS 30

<

TESTING
You really should y’know

31
<
Why test?
Yes, you’re keen to get this thing boxed and cranked, but testing is important. Why’s that?

• It MAY save time in the long run

There’s a good chance your finished pedal will work fine if you skip the test stage, in which
case - kudos. But don’t push your luck. One of your builds at some point is going to fizzle and
pop or do nothing at all when you stomp it. If only you’d done this test stage it’d save having to
pull it all apart.

• It will definitely narrow down any issues

If the worst does happen, and your circuit isn’t sounding like it oughta at this stage, as least
you’ve got it pinned down to something on the main PCB. If you’d already attached your
daughterboard, jacks and footswitch then they also come into play as possible problems.

• It really doesn’t take much effort

OK, if you haven’t done the smart thing and purchased one of our tester units there’s a little bit
of time and faff involved, but nothing too outrageous. If you want to save a few quid you can
knock up a test rig with just two jacks, a battery snap and a 4-way SIL socket. Stay tuned.

By far the simplest way is to use one of our testers

There are several models, but in most cases you’ll be fine with the Simple Circuit Tester (pictured).
This has a strip of SIL sockets to insert your ribbon connector if using one, or screw terminals if
you prefer to use individual wires on your builds.

If you don’t want to invest the price

of a couple of beers, there are
other methods detailed overleaf.

TESTING > WHY? 32

<
Multi-use bodge rig
You can make a reuseable test rig with two jacks,
a battery snap and a 4-way SIL socket.

You can then test board with ribbon connectors as much as you like.

INPUT

IN
V
G
OUT

OUTPUT

It looks a little messy due to all the ground connections having to go together, but it works.

TESTING > ALTERNATIVES TO TEST RIGS 33

<
Not using ribbon? No prob
You’re just going to have to do a little desoldering
on the jacks and battery snap after testing.

Build your circuit and add your four lengths of wire to the I V G O pads. Make them nice and lengthy
as you’re probably going to cut them after testing.

You then wire up a temporary test configuration a lot like the previous page, but without the socket.
Instead of wiring the battery + to the main PCB, join the battery wire to the length of wire you’ve
connected to the main board.

INPUT

OUTPUT

Once tested, desolder the wires from the jacks, trim them to a better length for final assembly and
move onto the next stage. Job done.

TESTING > ALTERNATIVES TO TEST RIGS 34

<

FINAL
ASSEMBLY
Nearly there...

35
<
Still a little way to go
You’re going to have to scroll on further to find specific
instructions for your chosen bypass type, but the basic
method is the same regardless.

In most cases you’re going to have two jacks, a DC socket and a footswitch of some sort.
These all connect to a daughterboard which in turn drops onto your footswitch and connects
to your main circuit, completing the picture.

Our recommended assembly order in the enclosure:

1 DC socket
It’s a bit fiddly trying to get the nut on once the footswitch is in place, so do this first.

2 Footswitch
It’s important to assemble this correctly. There are two nuts. One goes right down the threaded
part until it almost touches the body of the switch. Don’t set it right against the body. This nut
is there to put all the strain on the threads rather than where the body meets them. If you don’t
include this nut the switch will just pull apart when fastened up.

Next there’s either a serrated anti-vibration washer (3PDT switches) or a split washer (Alpha
DPDT switches) that goes on the inside of the enclosure against this first nut. Slip the
footswtich through the hole in the enclosure. Add the smooth washer if you have one, or
indeed want to include one, then the final nut to fasten it. Ensure it’s straight and tighten.

3 Jacks
Washer and nut on the outside of the enclosure. Fasten very loosely at first. Take note of the
position of the lugs in case they’ll interfere with the circuit board. Don’t fully tighten until the
circuit board is in place and you’ve manoeuvred the ribbon cable below them if necessary.

4 Main circuit board

Once this is in you can fasten those pots right up.

5 Footswitch daughterboard
...which you’ve already prepped after looking at that specific section.

Then it’s just a case of soldering everything to the daughterboard. We recommend doing the DC
socket wires first, as they’ll be hard to get to once the daughterboard is placed onto the footswtich.
We then locate the ribbon connector into the daughterboard pads and place the board onto the
footswitch before soldering them in, just to ensure everything sits nicely. Then just make all your
other connections. Everything should be readily accessible.

FINAL ASSEMBLY 36
<

Ensure your footswitch is straight, otherwise

your ribbon connector will be twisted when
soldered to the daughterboard.

And it just looks nicer than wonkly.

We prefer to have the DC socket oriented as

shown. It makes for easy access for the wiring.

Daughterboard prep
It’s easiest to add your wires before soldering the PCB to the footswitch.
Here’s a typical example for a standard box layout as above.

As a rough guide we’d say:

DC + and G - 20mm

Input jack ground - 25mm

Input jack signal (JI) - 40mm

Output jack signal (JO) - 20mm

Output jack ground - 40mm

FINAL ASSEMBLY 37
<

Note the position of the ribbon cable. It’s been curved below the jacks and is pointing straight up
around the same level as the footswitch poles, ready to drop the daughtboard onto.

FINAL ASSEMBLY 38
<
Dealing with the LED
We don’t use bezels, so this is what we do.

Before you solder the daughterboard to the footswitch you need to get the LED in there.

Before that, solder your Current Limiting Resistor, which stops the power destroying your LED, into
the two pads marked CLR. It should go on the underside of the daughterboard, positioned verically
as shown below.

You’re not soldering the LED yet. Just push the legs into the pads, slide it up a ways and then bend
the legs to stop it falling out.

Do the rest of your assembly, then this final step. Push the LED down through the daughterboard
and locate it into the hole in the enclosure. It’ll be nice and snug, and may need a little push with
your pliers. Ensure the legs aren’t twisted at all or touching each other. Once you’re happy, solder it
in. It’s now just as secure as if it had one of those ugly bezels. It’s good enough for EHX, Boss and
many others, so it should be good enough for you. If not, source a bezel. Myeh.

FINAL ASSEMBLY > LED 39

<

Awesome FUZZ

Clean
TONE

BYPASS
Several variations, same results

40
<
More than one way...
We offer several bypass switching options. The basic idea is the same in each case, but different
circuit boards are utilisied in each. You don’t have to use a daughterboard, but we highly
recommend them. If you want to do without you’ll have to find a way to secure your LED in the
enclosure. There are plenty of resources for wiring diagrams - search ‘3PDT true bypass wiring’.

In all cases we’re dealing with the same four main connections between your
main circuit board and your footswitch bypass daughterboard:

In V G Out
I or CI The signal being sent to the main circuit
V Your positive power supply, normally 9V DC
G The ground connection
O or CO The output of the main circuit

The other connections on the daughterboard are also the same in each case:
JI The connection to your input jack socket
V Positive connection to the DC power socket
G Negative connection to the DC power socket
JO The output jack socket.

However, not every connection will necessarily be made on the daughterboard depending on the
configuration of the main circuit board and your chosen pedal layout. This will be outlined later.

Identify the daughterboard you have below and click on it to go to that section. The first three utilise
our standard 3PDT or Gørva footswitches, the OptoPuss uses Alpha DPDT switches. The original
3PDT PCB is being phased out as supplies run out, being replaced with the compact version. The
connections are the same for each board but positioned in different places, so we’ll show each in
the following pages.

IMPORTANT - in every variant the Current Limiting Resistor (CLR) should be placed on the
daughterboard. Our older main circuit boards have a space for it,
but you should leave this empty. If your main PCB has a pad
marked LED to the right of the IVGO connections, this is the case.

3PDT - ORIGINAL 3PDT - COMPACT 3PDT - TOP LED OPTOPUSS

BYPASS 41
<
3PDT - Original
No battery provision

This configuration is for DC power supply only.

If using the mini-DC socket the red wire goes to the longer pin.

BYPASS > 3PDT ORIGINAL 42

<
3PDT - Original
Battery provision

This configuration allows for battery or DC power.

The battery ground is disconnected when your input jack is removed, so your battery won’t drain.
The battery is disconnected when you insert a DC power plug. This requires a TRS jack socket.

BYPASS > 3PDT ORIGINAL 43

<
3PDT - COMPACT
No battery provision

This configuration is for DC power supply only.

If using the mini-DC socket the red wire goes to the longer pin.

BYPASS > 3PDT COMPACT 44

<
3PDT - COMPACT
Battery provision

This configuration allows for battery or DC power.

The battery ground is disconnected when your input jack is removed, so your battery won’t drain.
The battery is disconnected when you insert a DC power plug. This requires a TRS jack socket.

BYPASS > 3PDT COMPACT 45

<
3PDT - TOP LED
No battery provision

This configuration is for DC power supply only.

If using the mini-DC socket the red wire goes to the longer pin.

This board was designed to go with main circuit boards that provide the jack connections on-board.
There are no pads for the jack grounds, so it’s a bit messy to use on ‘normal’ builds. See later.

BYPASS > 3PDT TOP LED 46

<
3PDT - TOP LED
Battery provision

This configuration allows for battery or DC power.

The battery ground is disconnected when your input jack is removed, so your battery won’t drain.
The battery is disconnected when you insert a DC power plug. This requires a TRS jack socket.
As you can see, the ground connections will get a bit messy. We don’t recomment this other than to
use with main circuit boards designed specifically to go with it.

BYPASS > 3PDT TOP LED 47

<
DPDT - OPTOPUSS
The OptoPuss utilises some circuitry to switch your signal.

This all goes on the same side of the PCB as the footswitch.

R1 2K2-4K7
C1 220n
OK1 TLP222G or A*
D1 1N4001
D2 LED**
SW1 Latching DPDT

How does it work?

When bypassed there’s no power going to the internal LED of the Optocoupler (pins 1+2). This keeps
the connections between pins 3+4 (the FET) open. This means the input of the connected circuit (CI -
Circuit In) is connected to ground and your signal goes from JI (Jack In) straight to JO (Jack Out).
IMPORTANT - be super careful soldering the optocoupler - they’re very easy to overheat.

When the switch is latched you’re connecting pins 1+2 from

V to GND via C1, R1 and the LED. This current flow lights
the optocoupler’s internal LED, causing a drop in
resistance between pins 3+4 to almost nothing. Now JI is
connected to CI, and CO is connected to JO - your signal
goes from Jack In > Circuit In > Circuit Out > Jack Out and
all is well.

*Note orientation of OK1 on the image. Dot indicates pin 1.

The board has been designed for Alpha brand

footswitches. Others may fit.

BYPASS > OPTOPUSS 48

<
DPDT - OPTOPUSS
No battery provision

This configuration is for DC power supply only.

If using the mini-DC socket the red wire goes to the longer pin.

BYPASS > OPTOPUSS 49

<
DPDT - OPTOPUSS
Battery provision

This configuration allows for battery or DC power.

The battery ground is disconnected when your input jack is removed, so your battery won’t drain.
The battery is disconnected when you insert a DC power plug. This requires a TRS jack socket.

BYPASS > OPTOPUSS 50

<
Variations on a theme
There are times other wiring variations will be available on your build, when a main circuit board
has provision for a top-side DC socket or even top-side jacks.

We’ll only illustrate one of each case here, as the basic principle is the same for every one of our
bypass boards. You simply make the appropriate connections on the main PCB instead of the
daughterboard, and in the case of top-jacks you should use all six of the connecting pads between
the main PCB and the daughterboard.

BYPASS > VARIATIONS 51

<
TOP-MOUNTED DC SOCKET
Sometimes our main PCBs will have pads at the top of the board for the V and G connections, as
seen in the illustration here. In this case you can simply eliminate the DC V and G connections from
the daughterboard and make them on the main PCB instead.

BYPASS >VARIATIONS > TOP-MOUNTED DC SOCKET 52

<
TOP DC AND JACKS
In some cases our main PCBs will have pads at the top of the board for the power and jacks
connections, as seen below. In this case the only connections you need to make to the
daughterboard are the six pads corresponding to the main PCB. This is entirely optional of course.
You could ignore the pads on the main PCB and wire it as normal with just the four connections,
using the daughterboard for your jacks and DC.

BYPASS >VARIATIONS > TOP-MOUNTED DC AND JACKS 53

<
POSITIVE-GROUND
Some circuits are positive-ground. Often these will have an onboard voltage inverter which enables
them to be powered by a standard negative-ground supply. If not you can wire them with the power
connections reversed. A downside of this is you can’t daisychain this with standard negative ground
pedals. It will need its own supply or battery power.

BYPASS >VARIATIONS > POSITIVE GROUND 54

<

We hope this document has been of help.

We’ve tried to make it as

comprehensive as possible.

If you have any comments or suggestions for improvement,

please feel free to get in touch.

Cheers from Team FuzzDog

Contents of this document are ©2023 Pedal Parts Ltd.

No reproduction permitted without the express written permission of Pedal Parts Ltd. All rights reserved.