0% found this document useful (0 votes)
143 views4 pages

ls2 Torque Specs

The document provides specifications for tightening various fasteners for a 2006 Chevrolet Corvette engine, listing the application, metric torque specification, and English torque specification. It includes over 70 individual fastener specifications.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
143 views4 pages

ls2 Torque Specs

The document provides specifications for tightening various fasteners for a 2006 Chevrolet Corvette engine, listing the application, metric torque specification, and English torque specification. It includes over 70 individual fastener specifications.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

Document ID: 1409810 Page 1 of 4

2006 Chevrolet Corvette | Corvette VIN Y Service Manual | Document ID: 1409810

Fastener Specifications
Fastener Tightening Specifications

Specification

Application Metric English

Camshaft Position (CMP) Sensor Bolt 12 Y 106 lb in

CMP Sensor Wire Harness Bolt 12 Y 106 lb in

Camshaft Retainer Bolts – Hex Head Bolts 25 Y 18 lb ft

Camshaft Retainer Bolts – TORX® Head Bolts 15 Y 11 lb ft

Camshaft Sprocket Bolts 25 Y 18 lb ft

Clutch Pressure Plate Bolts 70 Y 52 lb ft

Connecting Rod Bolts – First Pass 20 Y 15 lb ft

Connecting Rod Bolts – Final Pass 85 degrees

Coolant Air Bleed Pipe and Cover Bolts 12 Y 106 lb in

Coolant Temperature Sensor 20 Y 15 lb ft

Crankshaft Balancer Bolt – Installation Pass to Ensure


330 Y 240 lb ft
the Balancer is Completely Installed

Crankshaft Balancer Bolt – First Pass – Install a NEW


Bolt After the Installation Pass and Tighten as 50 Y 37 lb ft
Described in the First and Final Passes

Crankshaft Balancer Bolt – Final Pass 140 degrees

Crankshaft Bearing Cap M10 Bolts – First Pass in


20 Y 15 lb ft
Sequence

Crankshaft Bearing Cap M10 Bolts – Final Pass in


80 degrees
Sequence

Crankshaft Bearing Cap M10 Studs – First Pass in


20 Y 15 lb ft
Sequence

Crankshaft Bearing Cap M10 Studs – Final Pass in


51 degrees
Sequence
© 2017 General Motors. All rights reserved.

https://gsi.ext.gm.com/gsi/showDoc.do?docSyskey=1409810&cellId=133779&pubObjSyskey=2818920&from=sm&pubCellSyskey=8... 2/27/2017
Document ID: 1409810 Page 2 of 4

Specification

Application Metric English

Crankshaft Bearing Cap M8 Bolts 25 Y 18 lb ft

Crankshaft Oil Deflector Nuts 25 Y 18 lb ft

Crankshaft Position (CKP) Sensor Bolt 25 Y 18 lb ft

Crankshaft Rear Oil Seal Housing Bolts 30 Y 22 lb ft

Cylinder Head M11 Bolts – First Pass in Sequence 30 Y 22 lb ft

Cylinder Head M11 Bolts – Second Pass in Sequence 90 degrees

Cylinder Head M11 Bolts – Final Pass in Sequence 70 degrees

Cylinder Head M8 Bolts – in Sequence 30 Y 22 lb ft

Cylinder Head Coolant Plug 20 Y 15 lb ft

Engine Block Coolant Drain Hole Plug 60 Y 44 lb ft

Engine Block Coolant Heater 40 Y 30 lb ft

Engine Block Oil Gallery Plug 60 Y 44 lb ft

Evaporative Emission (EVAP) Canister Purge Solenoid


50 Y 37 lb ft
Valve Bolt

Exhaust Manifold Bolts – First Pass 15 Y 11 lb ft

Exhaust Manifold Bolts – Final Pass 20 Y 15 lb ft

Exhaust Manifold Heat Shield Bolts 9Y 80 lb in

Exhaust Manifold Studs 20 Y 15 lb ft

Flywheel Bolts – First Pass 20 Y 15 lb ft

Flywheel Bolts – Second Pass 50 Y 37 lb ft

Flywheel Bolts – Final Pass 100 Y 74 lb ft

Front Cover Bolts 25 Y 18 lb ft

Fuel Injection Fuel Rail Bolts 10 Y 89 lb in

https://gsi.ext.gm.com/gsi/showDoc.do?docSyskey=1409810&cellId=133779&pubObjSyskey=2818920&from=sm&pubCellSyskey=8... 2/27/2017
Document ID: 1409810 Page 3 of 4

Specification

Application Metric English

Ignition Coil Bracket-to-Valve Rocker Arm Cover Stud 12 Y 106 lb in

Ignition Coil-to-Bracket Bolts 10 Y 89 lb in

Intake Manifold Bolts – First Pass in Sequence 5Y 44 lb in

Intake Manifold Bolts – Final Pass in Sequence 10 Y 89 lb in

J 41798 M8 Bolt 25 Y 18 lb ft

J 41798 M10 Bolts 50 Y 37 lb ft

Knock Sensor Bolts 25 Y 18 lb ft

Motor Mount Bracket Bolts 50 Y 37 lb ft

Oil Cooler Bolts 12 Y 106 lb in

Oil Filter 30 Y 22 lb ft

Oil Filter Fitting 55 Y 40 lb ft

Oil Level Indicator Tube Bolt 25 Y 18 lb ft

Oil Level Sensor 20 Y 15 lb ft

Oil Pan Closeout Cover Bolt – Left Side 9Y 80 lb in

Oil Pan Closeout Cover Bolt – Right Side 9Y 80 lb in

Oil Pan Cover Bolts 12 Y 106 lb in

Oil Pan Drain Plug 25 Y 18 lb ft

Oil Pan M6 Bolts – Oil Pan-to-Rear Oil Seal Housing 12 Y 106 lb in

Oil Pan M8 Bolts – Oil Pan-to-Engine Block and Oil Pan


25 Y 18 lb ft
-to-Front Cover

Oil Pressure Sensor 35 Y 26 lb ft

Oil Pump Cover Bolts 12 Y 106 lb in

Oil Pump Relief Valve Plug 12 Y 106 lb in

https://gsi.ext.gm.com/gsi/showDoc.do?docSyskey=1409810&cellId=133779&pubObjSyskey=2818920&from=sm&pubCellSyskey=8... 2/27/2017
Document ID: 1409810 Page 4 of 4

Specification

Application Metric English

Oil Pump Screen Nuts 25 Y 18 lb ft

Oil Pump Screen-to-Oil Pump Bolt 12 Y 106 lb in

Oil Pump-to-Engine Block Bolts 25 Y 18 lb ft

Spark Plugs 15 Y 11 lb ft

Throttle Body Bolts 10 Y 89 lb in

Timing Chain Dampener Bolts 25 Y 18 lb ft

Valley Cover Bolts 25 Y 18 lb ft

Valve Lifter Guide Bolts 10 Y 89 lb in

Valve Rocker Arm Bolts 30 Y 22 lb ft

Valve Rocker Arm Cover Bolts 12 Y 106 lb in

Water Inlet Housing Bolts 15 Y 11 lb ft

Water Pump Bolts – First Pass 15 Y 11 lb ft

Water Pump Bolts – Final Pass 30 Y 22 lb ft

https://gsi.ext.gm.com/gsi/showDoc.do?docSyskey=1409810&cellId=133779&pubObjSyskey=2818920&from=sm&pubCellSyskey=8... 2/27/2017

You might also like