raper / Subject Code: 59009 / Elective 1:Analysis &Design of Multistorey Buildings

ME CivilSem I
R-22-23
Max, Marks: 80
Time: 3 hours

Note: I].Question Number one is compulsory

remaining five
2]. Attempt any three questions fromn
3]Assume any other data needed suitably, if not given. However, justify the same
covered.
4] Figures to the right indicate full marks and Course outcomes
S]IS 1893-2016 IS 13920 is permitted
(20)
Q.No.1 Solve any Four

a) Explain with sketch Centre of Mass and Centrc of Rigidity

b)Explain with sketches failurc mechanism of in filled frames
Frame
c) Ordinary Moment-Resting Frame and Special Moment-Resting
d)Response Reduction Factor (R)
e) Zone Factor (Z )

in fig. The storey (20)

QNO2 A 10 storey OMRF building has plan dimensions as shown
consisting of the floor slab
height is 3.5 meter. The DL per unit area of the floor,
to be 2
finishes etc is 5 kN/m Weight of the partition on the floor can be assumed
on the roof is 1.5
kN/m The intensity of live load on each floor is 4 kN/m and
in Delhi.
kN/m The soil below the foundation is hard and building is located
Determine the seismic forces and shears at different floor levels.
Beam of size 300mm x 750 mm
Column of size 300.mm X 750 mm
(20)

14736 1

IAE8418CED6360OE3EOD2F09F74B605B4
 QNo.4 illsi 2.1
ei
ioon
ei
BeamTake Max bsbcad
Shear Axil ti
concreteDesign
ColumnC1-4 Storey Q.NO.3
Self-weightPeriphery
wall:
partial
andBending force load C1
Sm Load 400 er
6m
column and= the 5-15
safety 570OkN at x400 Subject
6 ductile calculation.
seismic
load
Determine A
m
Moment base tor of on
Sm Typical
T sizefactor steel kN/m: beam kN/m, the mm, C2
= Code:
=1400kN shear slab
=30,000kNm Fe Storey
3 M30; the
floor
300mm = Sm
C1
415 ColumnkN/m centre
59009
Shear
waif 1.5 wall 6
kN/m?. C2,450 4- plan
for C3
to 15 C2
/
6m x500 the ofand Elective
resist C2-5 ;LivekN/m mass
mm following x450mm, part
the kN/m: load and I:
m
6 elevation
2 Analysis
seismic centre.
data. on
M30;
Sheaf
walt 4
slab of of
Sm &
Refer
forces C3 Sm rigidity six Design
kN/m:V 4
kN/m
C3-6 500 stored
figure 4 4m
using of of
Floor 6
500mm, x floor
building Multistorey
below M25 Floor 5

5
in
gradeof M30; shown
context
Buildings
in
vith Gc
(20)
(20)
Paper /Subject Code: 59009 /Electivel:Analysis &Design of Matistorey Baildings

third (20)
frames spaced at 45 t oc. The
Q.No 5 Afive storicd building has 6 msigle span with
kN/m.
of ( 25+ 20)
floor beam of front clevation is subjected to á characteristic udl
supported on
depth and is
The beam has a Section of 300 tmm wide x500 mm overall
reinforcements at
The beam
column with size 400 mm x 400 mm at either ends. column joint
and 3-20 mm tor at bottom while at beam-
centre are 2-20 mm tor at top 3-20 mmtor
4-20 mm tor extraand at bottom
tot +
the top reinforcement is 2-20 mm combinations is
from various load
with normal ductile detailing. The design shear fromthe
support and also at 2d
230 kN at support. Designthe shear reinforcement at
grade concrete and
support as per IS: 13920. The materials are M25
Tace of the
HYSD reinforcement of grade Fe415.

2000
2000

-20
300
--208

-F201

column of size 450 mm x450 mm (20)

Q.No.6 Design the reinforcement for a
,subjected unsupported length of 3,0
tothe following forces. The column has andirections. Use M25 Fe
both
m and is braced against side sway in Seismic load = 550 kN Live load
415 Axial load dead load =1000 kN
kNm Live load = 40 kNm
-800 kN and Moment dead load =50
Seismic load = 100 kNm

3
14736

IAE8418CED6360E3EOD2FO9F74B60SB4