Power Distribution Systems

June 2006
Sheet 0019

1.0-1

Index

Master TOC

Power Distribution Systems

Contents
Power Distribution Systems System Design Basic Principles. . . . . . . . . . . 1.1-1 Modern Electric Power Technologies . . . . . . . . . . . 1.1-1 Goals of System Design . . . 1.1-2 Voltage Classications; BILs Basic Impulse Levels . . . . . 1.1-4 3-Phase Transformer Winding Connections . . . . 1.1-5 Types of Systems Radial, Loop, Selective, Two-Source, Sparing Transformer, Spot Network, Distribution . . . . 1.1-6 Health Care Facility Design Considerations . . . 1.1-14 Generator Systems . . . . . . 1.1-17 Generator System Design Types of Generators . . . . . . . 1.2-1 Generator Systems . . . . . . . 1.2-2 Generator Grounding. . . . . . 1.2-3 Generator Controls. . . . . . . . 1.2-4 Generator Short Circuit Characteristics . . . . . . . . . . 1.2-4 Generator Protection . . . . . . 1.2-5 System Analysis Systems Analysis . . . . . . . . . 1.3-1 Short Circuit Currents . . . . . 1.3-2 Fault Current Waveform Relationships . . . . . . . . . . . 1.3-3 Fault Current Calculations and Methods Index . . . . . . 1.3-4 Determine X and R from Transformer Loss Data . . . 1.3-19 Voltage Drop Considerations . . . . . . . . . . 1.3-23 System Application Considerations Capacitors/Power Factor. . . 1.4-1 Overcurrent Protection and Coordination . . . . . . . . 1.4-3 Protection of Conductors . . . 1.4-5 Circuit Breaker Cable Temperature Ratings . . . . . 1.4-5 Zone Selective Interlocking . 1.4-5 Ground Fault Protection . . . 1.4-6 Suggested Ground Fault Settings . . . . . . . . . . . . . 1.4-6 Grounding/Ground Fault Protection Grounding Equipment, System, MV System, LV System . . . . . . . . . . . . . . 1.4-6 Ground Fault Protection . . . . 1.4-11 Lightning and Surge Protection . . . . . . . . . . . . . . 1.4-14 Grounding Electrodes. . . . . . 1.4-14 Power Quality Terms, Technical Overview . . 1.4-15 TVSS . . . . . . . . . . . . . . . . . . . 1.4-16 Harmonics and Nonlinear Loads . . . . . . . . . 1.4-18 UPS . . . . . . . . . . . . . . . . . . . . 1.4-22 Other Application Considerations Secondary Voltage . . . . . . . . 1.4-28 Energy Conservation . . . . . . 1.4-29 Building Control Systems . . 1.4-30 Cogeneration. . . . . . . . . . . . . 1.4-30 Emergency Power. . . . . . . . . 1.4-30 Peak Shaving. . . . . . . . . . . . . 1.4-31 Sound Levels. . . . . . . . . . . . . 1.4-32 Reference Data IEEE Protective Relay Numbers . . . . . . . . . . . . . . . 1.5-1 Codes and Standards . . . . . . 1.5-6 Motor Protective Device Data . . . . . . . . . . . . . 1.5-7 Chart of Short Circuit Currents for Transformers . . 1.5-9 Transformer Full Load Amperes and Impedances . . . . . . . . . 1.5-10 Transformer Losses, TP-1 Losses . . . . . . . . . . . . . 1.5-12 Power Equipment Losses . . . 1.5-13 NEMA Enclosure Denitions . . 1.5-13 Cable R, X, Z Data . . . . . . . . . 1.5-15 Conductor Ampacities . . . . . 1.5-16 Conductor Temperature Ratings . . . . . . . . . . . . . . . . 1.5-16 Formulas and Terms . . . . . . . 1.5-18 Seismic Requirements . . . . . 1.5-19

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

Designing a Distribution System

21

CA08104001E

For more information visit: www.EatonElectrical.com

1.0-2

Power Distribution Systems

TOC Index

June 2006
Sheet 0020

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

This page intentionally left blank.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0021

TOC

Index

Power Distribution Systems System Design

1.1-1

Master TOC

Basic Principles
The best distribution system is one that will, cost effectively and safely, supply adequate electric service to both present and future probable loads this section is included to aid in selecting, designing and installing such a system. The function of the electric power distribution system in a building or installation site is to receive power at one or more supply points and deliver it to the individual lamps, motors, and all other electrically operated devices. The importance of the distribution system to the function of a building makes it almost imperative that the best system be designed and installed. In order to design the best distribution system, the system design engineer must have information concerning the loads and a knowledge of the various types of distribution systems that are applicable. The various categories of buildings have many specic design challenges, but certain basic principles are common to all. Such principles, if followed, will provide a soundly executed design.

The basic principles or factors requiring consideration during design of the power distribution system include:
s s s

Modern Electric Power Technologies

Several new factors to consider in modern power distribution systems result from two relatively recent changes. The rst recent change is utility deregulation. The traditional dependence on the utility for problem analysis; energy conservation measurements and techniques; and a simplied cost structure for electricity has changed. The second change is less obvious to the designer yet will have an impact on the types of equipment and systems being designed. It is the diminishing quantity of qualied building electrical operators; maintenance departments; and facility engineers. Modern electric power technologies may be of use to the designer and building owner in addressing these new challenges. The advent of microprocessor devices (smart devices) into power distribution equipment has expanded facility owners options and capabilities, allowing for automated communication of vital power system information (both energy data and system operation information) and electrical equipment control. These technologies may be grouped as:
s s s s s

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

s s

s s s s s s s s s

Functions of structure, present and future. Life and exibility of structure. Locations of service entrance and distribution equipment, locations and characteristics of loads, locations of unit substations. Demand and diversity factors of loads. Sources of power; including normal, standby and emergency (see Section 42). Continuity and quality of power available and required (see Section 41). Energy efciency and management. Distribution and utilization voltages. Bus and/or cable feeders. Distribution equipment and motor control. Power and lighting panelboards and motor control centers. Types of lighting systems. Installation methods. Power monitoring systems. Electric utility requirements.

Power monitoring and control. Building management systems interfaces. Lighting control. Automated energy management. Predictive diagnostics.

Various sections of this guide cover the application and selection of such systems and components that may be incorporated into the power equipment being designed. See Sections 2, 3, 4, 23 and 43.

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-2

Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0022

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Goals of System Design

When considering the design of an electrical distribution system for a given customer and facility, the electrical engineer must consider alternate design approaches which best t the following overall goals. 1. Safety: The No. 1 goal is to design a power system which will not present any electrical hazard to the people who utilize the facility, and/or the utilization equipment fed from the electrical system. It is also important to design a system which is inherently safe for the people who are responsible for electrical equipment maintenance and upkeep. The National Electrical Code (NEC), NFPA 70 and NFPA 70E, as well as local electrical codes provide minimum standards and requirements in the area of wiring design and protection, wiring methods and materials as well as equipment for general use with the overall goal of providing safe electrical distribution systems and equipment. The NEC also covers minimum requirements for special occupancies including hazardous locations and special use type facilities such as health care facilities, places of assembly, theaters, etc. and the equipment and systems located in these facilities. Special equipment and special conditions such as emergency systems, standby systems and communication systems are also covered in the code. It is the responsibility of the design engineer to be familiar with the NFPA and NEC code requirements as well as the customers facility, process, and operating procedures; to design a system which protects personnel from electrical live conductors and utilizes adequate circuit protective devices which will selectively isolate overloaded or faulted circuits or equipment as quickly as possible.

2. Minimum Initial Investment: The owners overall budget for rst cost purchase and installation of the electrical distribution system and electrical utilization equipment will be a key factor in determining which of various alternate system designs are to be selected. When trying to minimize initial investment for electrical equipment, consideration should be given to the cost of installation, oor space requirements and possible extra cooling requirements as well as the initial purchase price. 3. Maximum Service Continuity: The degree of service continuity and reliability needed will vary depending on the type and use of the facility as well as the loads or processes being supplied by the electrical distribution system. For example, for a smaller commercial ofce building a power outage of considerable time, say several hours, may be acceptable, whereas in a larger commercial building or industrial plant only a few minutes may be acceptable. In other facilities such as hospitals, many critical loads permit a maximum of 10 seconds outage and certain loads, such as real-time computers, cannot tolerate a loss of power for even a few cycles. Typically, service continuity and reliability can be increased by: A. Supplying multiple utility power sources or services. B. Supplying multiple connection paths to the loads served. C. Using short-time rated power circuit breakers. D. Providing alternate customerowned power sources such as generators or batteries supplying uninterruptable power supplies. E. Selecting the highest quality electrical equipment and conductors. F. Using the best installation methods. G. Designing appropriate system alarms, monitoring and diagnostics. H. Selecting preventative maintenance systems or equipment to alarm before an outage occurs.

4. Maximum Flexibility and Expendability: In many industrial manufacturing plants, electrical utilization loads are periodically relocated or changed requiring changes in the electrical distribution system. Consideration of the layout and design of the electrical distribution system to accommodate these changes must be considered. For example, providing many smaller transformers or loadcenters associated with a given area or specic groups of machinery may lend more exibility for future changes than one large transformer; the use of plug-in busways to feed selected equipment in lieu of conduit and wire may facilitate future revised equipment layouts. In addition, consideration must be given to future building expansion, and/or increased load requirements due to added utilization equipment when designing the electrical distribution system. In many cases considering transformers with increased capacity or fan cooling to serve unexpected loads as well as including spare additional protective devices and/ or provision for future addition of these devices may be desirable. Also to be considered is increasing appropriate circuit capacities or quantities for future growth. Power monitoring communication systems connected to electronic metering can provide the trending and historical data necessary for future capacity growth.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0023

TOC

Index

Power Distribution Systems System Design

1.1-3

Master TOC

5. Maximum Electrical Efciency (Minimum Operating Costs): Electrical efciency can generally be maximized by designing systems that minimize the losses in conductors, transformers and utilization equipment. Proper voltage level selection plays a key factor in this area and will be discussed later. Selecting equipment, such as transformers, with lower operating losses, generally means higher rst cost and increased oor space requirements; thus, there is a balance to be considered between the owners utility energy change for the losses in the transformer or other equipment versus the owners rst cost budget and cost of money. 6. Minimum Maintenance Cost: Usually the simpler the electrical system design and the simpler the electrical equipment, the less the associated maintenance costs and operator errors. As electrical systems and equipment become more complicated to provide greater service continuity or exibility, the maintenance costs and chance for operator error increases. The systems should be designed with an alternate power circuit to take electrical equipment (requiring periodic maintenance) out of service without dropping essential loads. Use of drawout type protective devices such as breakers and combination starters can also minimize maintenance cost and out-of-service time.

7. Maximum Power Quality: The power input requirements of all utilization equipment has to be considered including the acceptable operating range of the equipment and the electrical distribution system has to be designed to meet these needs. For example, what is the required input voltage, current, power factor requirement? Consideration to whether the loads are affected by harmonics (multiples of the basic 60 cycle per second sine wave) or generate harmonics must be taken into account as well as transient voltage phenomena. The above goals are interrelated and in some ways contradictory. As more redundancy is added to the electrical system design along with the best quality equipment to maximize service continuity, exibility and expandability, and power quality, the more initial investment and maintenance are increased. Thus, the designer must weigh each factor based on the type of facility, the loads to be served, the owners past experience and criteria.

Summary
It is to be expected that the engineer will never have complete load information available when the system is designed. The engineer will have to expand the information made available to him on the basis of experience with similar problems. Of course, it is desirable that the engineer has as much denite information as possible concerning the function, requirements, and characteristics of the utilization devices. The engineer should know whether certain loads function separately or together as a unit, the magnitude of the demand of the loads viewed separately and as units, the rated voltage and frequency of the devices, their physical location with respect to each other and with respect to the source and the probability and possibility of the relocation of load devices and addition of loads in the future. Coupled with this information, a knowledge of the major types of electric power distribution systems equips the engineers to arrive at the best system design for the particular building. It is beyond the scope of this guide to present a detailed discussion of loads that might be found in each of several types of buildings. Assuming that the design engineer has assembled the necessary load data, the following pages discuss some of the various types of electrical distribution systems that can be utilized. The description of types of systems, and the diagrams used to explain the types of systems on the following pages omits the location of utility revenue metering equipment for clarity. A discussion of short circuit calculations, coordination, voltage selection, voltage drop, ground fault protection, motor protection, and other specic equipment protection is also presented.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-4

Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0024

Master TOC

i ii 1 2 3 4 5 6 7

Voltage Classications
ANSI and IEEE standards dene various voltage classications for single-phase and 3-phase systems. The terminology used divides voltage classes into:
s

Table 1.1-2. Metal-Clad Switchgear Voltage and Insulation Levels (From ANSI/IEEE C37.20.2-1999)
Rated Maximum Voltage (kV rms) 4.76 8.25 15.0 27.0 38.0 Impulse Withstand (kV) 60 95 95 125 150

Voltage Recommendations by Motor Horsepower

Some factors affecting the selection of motor operating voltage include:
s s s s s s

Low voltage. Medium voltage. s High voltage. s Extra-high voltage. s Ultra-high voltage.
s

Table 1.1-3. Metal-Enclosed Switchgear Voltage and Insulation Levels (From ANSI C37.20.3-1987)
Rated Maximum Voltage (kV rms) 4.76 8.25 15.0 15.5 25.8 38.0 Impulse Withstand (kV) 60 75 95 110 125 150

Table 1.1-1 presents the nominal system voltages for these classications. Table 1.1-1. Standard Nominal System Voltages and Voltage Ranges (From IEEE Standard 141-1993)
Voltage Class Low Voltage Nominal System Voltage 3-Wire 4-Wire 208Y/120 240/120 480Y/277

Motor, motor starter and cable rst cost. Motor, motor starter and cable installation cost. Motor and cable losses. Motor availability. Voltage drop. Qualications of the building operating staff; and many more.

The following table is based in part on the above factors and experience. Since all the factors affecting the selection are rarely known, it is only an approximate guideline. Table 1.1-5. Selection of Motor Horsepower Ratings as a Function of System Voltage
Motor Voltage Motor (Volts) hp Range 460 2,300 4,000 4,600 13,200 125 350 450 550 up to 500 250 to 2000 250 to 3000 250 to 3000 above 2000 System Voltage 480 2,400 4,160 4,800 13,800

240/120 240 480 600 2,400 4,160 4,800 6,900 13,200 13,800 23,000 34,500 46,000 69,000 115,000 138,000 161,000 230,000

Medium Voltage

8 9 10
High Voltage

4160Y/2400 8320Y/4800 12000Y/6930 12470Y/7200 13200Y/7620 13800Y/7970 20780Y/12000 22860Y/13200 24940Y/14400 34500Y/19920

Table 1.1-4. Liquid-Immersed Transformers Voltage and Basic Lightning Impulse Insulation Levels (BIL) (From ANSI/IEEE C57.12.00-2000)
Application Nominal BIL System (kV Crest) Voltage (kV rms) 1.2 2.5 5.0 8.7 15.0 25.0 34.5 46.0 69.0 Power 1.2 2.5 5.0 8.7 15.0 25.0 34.5 46.0 69.0 115.0 138.0 161.0 230.0 345.0 500.0 765.0 30 45 60 75 95 150 200 250 350 45 60 75 95 110 150 200 250 350 550 650 750 125 150 200 250 30 45 60 75 95 200 250 450 550 650

Distribution

Table 1.1-6. Dry-Type Transformers Voltage and Basic Lightning Impulse Insulation Levels (BIL) From ANSI/IEEE C57.12.01-1989)
Nominal System Voltage (kV rms) 1.2 2.5 5.0 8.7 15.0 25.0 34.5 BIL (kV Crest)

11 12 13 14 15 16 17 18 19 20 21
Extra-High Voltage

345,000 500,000 765,000 1,100,000

Ultra-High Voltage

95

10 20 30 45 60 110 125

20 30 45 60 95 125 150

30 45 60 95 110 150 200

BIL Basic Impulse Levels

ANSI standards dene recommended and required BIL levels for: Metal-Clad Switchgear (typically vacuum breakers). s Metal-Enclosed Switchgear (typically load interrupters, switches). s Liquid Immersed Transformers. s Dry-Type Transformers.
s

900 825 750 650 1,175 1,050 900 1,675 1,550 1,425 1,300 2,050 1,925 1,800

BIL values in bold typeface are listed as standard. Others listed are in common use. Optional higher levels used where exposure to overvoltage occurs and higher protection margins are required. Lower levels where surge arrester protective devices can be applied with lower spark-over levels.

Tables 1.1-2 through 1.1-6 contain those values.

BIL values in bold typeface are listed as standard. Others listed are in common use.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0025

TOC

Index

Power Distribution Systems System Design

1.1-5

Master TOC

Table 1.1-7. 3-Phase Transformer Winding Connections

Phasor Diagram
DELTA-DELTA Connection Phasor Diagram: H2 X2

Notes 1. Suitable for both ungrounded and effectively grounded sources. 2. Suitable for a 3-wire service or a 4-wire service with a mid-tap ground.

i ii 1

H1

H3

X1

X3

2
1. Suitable for both ungrounded and effectively grounded sources. 2. Suitable for a 3-wire service or a 4-wire grounded service with XO grounded. 3. With XO grounded, the transformer acts as a ground source for the secondary system. 4. Fundamental and harmonic frequency zero-sequence currents in the secondary lines supplied by the transformer do not ow in the primary lines. Instead the zero sequence currents circulate in the closed delta primary windings. 5. When supplied from an effectively grounded primary system does not see load unbalances and ground faults in the secondary system. 1. Suitable for both ungrounded and effectively grounded sources. 2. Suitable for a 3-wire service or a 4-wire delta service with a mid-tap ground. 3. Grounding the primary neutral of this connection would create a ground source for the primary system. This could subject the transformer to severe overloading during a primary system disturbance or load unbalance. 4. Frequently installed with mid-tap ground on one leg when supplying combination 3-phase and single-phase load where the 3-phase load is much larger than single-phase load. 5. When used in 25 kV and 35 kV 3-phase 4-wire primary systems, ferroresonance can occur when energizing or de-energizing the transformer using single-pole switches located at the primary terminals. With smaller kVA transformers the probability of ferroresonance is higher. 1. Suitable for both ungrounded and effectively grounded sources. 2. Suitable for a 3-wire service only, even if XO is grounded. 3. This connection is incapable of furnishing a stabilized neutral and its use may result in phase-to-neutral overvoltage (neutral shift) as a result of unbalanced phase-to-neutral load. 4. If a 3-phase unit is built on a three-legged core, the neutral point of the primary windings is practically locked at ground potential.

Angular Displacement (Degrees): 0 DELTA-WYE Connection Phasor Diagram: H2 X2 X1 H1 H3 X0 X3

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Angular Displacement (Degrees): 30 WYE-DELTA Connection Phasor Diagram: H2 X2

X1 H1 H3 X3

Angular Displacement (Degrees): 30

WYE-WYE Connection Phasor Diagram: H2 X2

X0 H1 H3 X1 X3

Angular Displacement (Degrees): 0

GROUNDED WYE-WYE Connection Phasor Diagram: H2 X2

H0 H1 H3 X1

X0 X3

Angular Displacement (Degrees): 0

1. Suitable for 4-wire effectively grounded source only. 2. Suitable for a 3-wire service or for 4-wire grounded service with XO grounded. 3. 3-phase transformers with this connection may experience stray ux tank heating during certain external system unbalances unless the core conguration (four or ve legged) utilized provides a return path for the ux. 4. Fundamental and harmonic frequency zero-sequence currents in the secondary lines supplied by the transformer also ow in the primary lines (and primary neutral conductor). 5. Ground relay for the primary system may see load unbalances and ground faults in the secondary system. This must be considered when coordinating overcurrent protective devices. 6. 3-phase transformers with the neutral points of the high voltage and low voltage windings connected together internally and brought out through an HOXO bushing should not be operated with the HOXO bushing ungrounded (oating). To do so can result in very high voltages in the secondary systems. 1. Suitable for both ungrounded and effectively grounded sources. 2. Suitable for a 3-wire service or a 4-wire service with a mid-tap ground. 3. When using the tap for single-phase circuits the single-phase load kVA should not exceed 5% of the 3-phase kVA rating of the transformer. The 3-phase rating of the transformer is also substantially reduced.

DELTA-DELTA Connection with Tap Phasor Diagram: H2 X4 X2

H1

H3

X1

X3

Angular Displacement (Degrees): 0

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-6

Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0026

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Types of Systems
In many cases, power is supplied by the utility to a building at the utilization voltage. In these cases, the distribution of power within the building is achieved through the use of a simple radial distribution system. In cases where the utility service voltage is at some voltage higher than the utilization voltage within the building, the system design engineer has a choice of a number of types of systems which may be used. This discussion covers several major types of distribution systems and practical modications of them. 1. Simple Radial. 2. Loop-Primary System Radial Secondary System. 3. Primary Selective System Secondary Radial System. 4. Two-Source Primary Secondary Selective System. 5. Sparing Transformer System. 6. Simple Spot Network. 7. Medium Voltage Distribution System Design.

Low voltage feeder circuits run from the switchgear or switchboard assemblies to panelboards that are located closer to their respective loads as shown in Figure 1.1-1. Each feeder is connected to the switchgear or switchboard bus through a circuit breaker or other overcurrent protective device. A relatively small number of circuits are used to distribute power to the loads from the switchgear or switchboard assemblies and panelboards. Since the entire load is served from a single source, full advantage can be taken of the diversity among the loads. This makes it possible to minimize the installed transformer capacity. However, the voltage regulation and efciency of this system may be poor because of the low voltage feeders and single source. The cost of the low voltagefeeder circuits and their associated circuit breakers are high when the feeders are long and the peak demand is above 1000 kVA.

A fault on the secondary low voltage bus or in the source transformer will interrupt service to all loads. Service cannot be restored until the necessary repairs have been made. A low voltage feeder circuit fault will interrupt service to all loads supplied over that feeder. A modern and improved form of the conventional simple radial system distributes power at a primary voltage. The voltage is stepped down to utilization level in the several load areas within the building typically through secondary unit substation transformers. The transformers are usually connected to their associated load bus through a circuit breaker, as shown in Figure 1.1-2. Each secondary unit substation is an assembled unit consisting of a 3-phase, liquid-lled or air-cooled transformer, an integrally connected primary fused switch, and low voltage switchgear or switchboard with circuit breakers or fused switches. Circuits are run to the loads from these low voltage protective devices.

Primary Fused Switch Transformer 600 V Class Switchboard

1. Simple Radial System

The conventional simple radial system receives power at the utility supply voltage at a single substation and steps the voltage down to the utilization level. In those cases where the customer receives his supply from the primary system and owns the primary switch and transformer along with the secondary low voltage switchboard or switchgear, the equipment may take the form of a separate primary switch, separate transformer, and separate low voltage switchgear or switchboard. This equipment may be combined in the form of an outdoor pad-mounted transformer with internal primary fused switch and secondary main breaker feeding an indoor switchboard. Another alternative would be a secondary unit substation where the primary fused switch, transformer and secondary switchgear or switchboard are designed and installed as a close coupled single assembly. In those cases where the utility owns the primary equipment and transformer, the supply to the customer is at the utilization voltage, and the service equipment then becomes low voltage main distribution switchgear or a switchboard.

Distribution Dry-Type Transformer Distribution Panel MCC Distribution Panel Lighting Panelboard

Figure 1.1-1. Simple Radial System

52 Primary Main Breaker

52 52 52 52 52 52 Primary Feeder Breakers

Primary Cables

Secondary Unit Substation

Figure 1.1-2. Primary and Secondary Simple Radial System

For more information visit: www.EatonElectrical.com CA08104001E

June 2006
Sheet 0027

TOC

Index

Power Distribution Systems System Design

1.1-7

Master TOC

Since each transformer is located within a specic load area, it must have sufcient capacity to carry the peak load of that area. Consequently, if any diversity exists among the load area, this modied primary radial system requires more transformer capacity than the basic form of the simple radial system. However, because power is distributed to the load areas at a primary voltage, losses are reduced, voltage regulation is improved, feeder circuit costs are reduced substantially, and large low voltage feeder circuit breakers are eliminated. In many cases the interrupting duty imposed on the load circuit breakers is reduced. This modern form of the simple radial system will usually be lower in initial investment than most other types of primary distribution systems for buildings in which the peak load is above 1000 kVA. A fault on a primary feeder circuit or in one transformer will cause an outage to only those secondary loads served by that feeder or transformer. In the case of a primary main bus fault or a utility service outage, service is interrupted to all loads until the trouble is eliminated. Reducing the number of transformers per primary feeder by adding more primary feeder circuits will improve the exibility and service continuity of this system; the ultimate being one secondary unit substation per primary feeder circuit. This of course increases the investment in the system but minimizes the extent of an outage resulting from a transformer or primary feeder fault. Primary connections from one secondary unit substation to the next secondary unit substation can be made with double lugs on the unit substation primary switch as shown, or with separable connectors made in manholes or other locations. Depending on the load kVA connected to each primary circuit and if no ground fault protection is desired for either the primary feeder conductors and transformers connected to that feeder or the main bus, the primary main and/or feeder breakers may be changed to primary fused switches. This will signicantly reduce the rst cost, but also decrease the level of conductor and equipment protection. Thus, should a fault or overload condition occur, downtime increases signicantly and higher costs associated with increased damage levels and the need for fuse replacement is typically encountered.
CA08104001E

In addition, if only one primary fuse on a circuit opens, the secondary loads are then single phased, causing damage to low voltage motors. Another approach to reducing costs is to eliminate the primary feeder breakers completely, and utilize a single primary main breaker or fused switch for protection of a single primary feeder circuit with all secondary unit sub-stations supplied from this circuit. Although this system results in less initial equipment cost, system reliability is reduced drastically since a single fault in any part of the primary conductor would cause an outage to all loads within the facility.

break switches with load side bus connection) sectionalizing switches and primary load break fused switch as shown in Figure 1.1-4. When pad-mounted compartmentalized transformers are utilized, they are furnished with loop feed oil immersed gang operated load break sectionalizing switches and drawout current limiting fuses in dry wells as shown in Figure 1.1-5. By operating the appropriate sectionalizing switches, it is possible to disconnect any section of the loop conductors from the rest of the system. In addition, by opening the transformer primary switch (or removing the load break drawout fuses in the pad-mounted transformer) it is possible to disconnect any transformer from the loop. A key interlocking scheme is normally recommended to prevent closing all sectionalizing devices in the loop. Each primary loop sectionalizing switch and the feeder breakers to the loop are interlocked such that to be closed they require a key (which is held captive until the switch or breaker is opened) and one less key than the number of key interlock cylinders is furnished. An extra key is provided to defeat the interlock under qualied supervision.

i ii 1 2 3 4 5 6 7 8 9 10

2. Loop Primary System Radial Secondary System

This system consists of one or more PRIMARY LOOPS with two or more transformers connected on the loop. This system is typically most effective when two services are available from the utility as shown in Figure 1.1-3. Each primary loop is operated such that one of the loop sectionalizing switches is kept open to prevent parallel operation of the sources. When secondary unit substations are utilized, each transformer has its own duplex (2-load

Primary Main Breaker 1 52

52 52 52

52 Primary Main Breaker 2

11 12 13

Tie Breaker

52

52

Loop Feeder Breaker

Loop A Loop B NC NO NC NC Fault Sensors

14 15 16

NC

NC

NO

NC

NC

NC

17 18 19

Secondary Unit Substations Consisting of: Duplex Primary Switches/Fused Primary Switches/ Transformer and Secondary Main Feeder Breakers

20 21

Figure 1.1-3. Loop Primary Radial Secondary System

For more information visit: www.EatonElectrical.com

1.1-8

Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0028

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Loop Feeder

Loop Feeder Load Break Loop Switches

Fused Disconnect Switch

Figure 1.1-4. Secondary Unit Substation Loop Switching

Loop Feeder Loop Feeder Load Break Loop Switches

When a primary feeder conductor fault occurs, the associated loop feeder breaker opens and interrupts service to all loads up to the normally open primary loop load break switch (typically half of the loads). Once it is determined which section of primary cable has been faulted, the loop sectionalizing switches on each side of the faulted conductor can be opened, the loop sectionalizing switch which had been previously left open then closed and service restored to all secondary unit substations while the faulted conductor is replaced. If the fault should occur in a conductor directly on the load side of one of the loop feeder breakers, the loop feeder breaker is kept open after tripping and the next load side loop sectionalizing switch manually opened so that the faulted conductor can be sectionalized and replaced.
Note: Under this condition, all secondary unit substations are supplied through the other loop feeder circuit breaker, and thus all conductors around the loop should be sized to carry the entire load connected to the loop. Increasing the number of primary loops (two loops shown in Figure 1.1-6) will reduce the extent of the outage from a conductor fault, but will also increase the system investment.

52

Loop A

Loop A

In cases where only one primary line is available, the use of a single primary breaker provides the loop connections to the loads as shown here.

Figure 1.1-6. Single Primary Feeder Loop System A basic primary loop system which utilizes a single primary feeder breaker connected directly to two loop feeder switches which in turn then feed the loop is shown in Figure 1.1-6. In this basic system the loop may be normally operated with one of the loop sectionalizing switches open as described above or with all loop sectionalizing switches closed. If a fault occurs in the basic primary loop system, the single loop feeder breaker trips, and secondary loads are lost until the faulted conductor is found and eliminated from the loop by opening the appropriate loop sectionalizing switches and then reclosing the breaker.

Load Break Drawout Fuses

Figure 1.1-5. Pad-Mounted Transformer Loop Switching In addition, the two primary main breakers which are normally closed and primary tie breaker which is normally open are either mechanically or electrically interlocked to prevent paralleling the incoming source lines. For slightly added cost, an automatic throw-over scheme can be added between the two main breakers and tie breaker. During the more common event of a utility outage, the automatic transfer scheme provides signicantly reduced power outage time. The system in Figure 1.1-3 has higher costs than in Figure 1.1-2, but offers increased reliability and quick restoration of service when 1) a utility outage occurs, 2) a primary feeder conductor fault occurs, or 3) a transformer fault or overload occurs. Should a utility outage occur on one of the incoming lines, the associated primary main breaker is opened and the tie breaker closed either manually or through an automatic transfer scheme.

When a transformer fault or overload occurs, the transformer primary fuses open, and the transformer primary switch manually opened, disconnecting the transformer from the loop, and leaving all other secondary unit substation loads unaffected.
Primary Metal-Clad Switchgear Lineup Bus A
52
52

3. Primary Selective System Secondary Radial System

The primary selective secondary radial system, as shown in Figure 1.1-7, differs from those previously described in that it employs at least two primary feeder circuits in each load area. It is

52

Primary Main Breaker Bus B

52
52

52

52

Primary Feeder Breaker

Feeder A1

Feeder B1

Feeder B2 Feeder A2

To Other Substations

NO

NC

NO

NC NO

Typical Secondary Unit Substation Duplex Primary Switch/Fuses Transformer/600 V Class Secondary Switchgear

NC

Figure 1.1-7. Basic Primary Selective Radial Secondary System

For more information visit: www.EatonElectrical.com CA08104001E

June 2006
Sheet 0029

TOC

Index

Power Distribution Systems System Design

1.1-9

Master TOC

designed so that when one primary circuit is out of service, the remaining feeder or feeders have sufcient capacity to carry the total load. Half of the transformers are normally connected to each of the two feeders. When a fault occurs on one of the primary feeders, only half of the load in the building is dropped. Duplex fused switches as shown in Figure 1.1-7 and detailed in Figure 1.1-8 are the normal choice for this type of system. Each duplex fused switch consists of two (2) load break 3-pole switches each in their own separate structure, connected together by bus bars on the load side. Typically, the load break switch closest to the transformer includes a fuse assembly with fuses. Mechanical and/or key interlocking is furnished such that both switches cannot be closed at the same time (to prevent parallel operation) and interlocking such that access to either switch or fuse assembly cannot be obtained unless both switches are opened.
Primary Feeders

Primary Feeders

Non-Load Break Selector Switches

Interlock Load Break Disconnect

or most of the loads, may more than offset the greater cost. Having twosources allows for either manual or automatic transfer of the two primary main breakers and tie breaker should one of the sources become unavailable. The primary selective-secondary radial system, however, may be less costly or more costly than a primary loop secondary radial system of Figure 1.1-3 depending on the physical location of the transformers while offering comparable downtime and reliability. The cost of conductors for the two types of systems may vary greatly depending on the location of the transformers and loads within the facility and greatly override primary switching equipment cost differences between the two systems.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Fuses

Figure 1.1-9. Fused Selector Switch in One Structure This means limited cable space especially if double lugs are furnished for each line as shown in Figure 1.1-7 and should a faulted primary conductor have to be changed, both lines would have to be deenergized for safe changing of the faulted conductors. In Figure 1.1-7 when a primary feeder fault occurs the associated feeder breaker opens, and the transformers normally supplied from the faulted feeder are out of service. Then manually, each primary switch connected to the faulted line must be opened and then the alternate line primary switch can be closed connecting the transformer to the live feeder, thus restoring service to all loads. Note that each of the primary circuit conductors for Feeder A1 and B1 must be sized to handle the sum of the loads normally connected to both A1 and B1. Similar sizing of Feeders A2 and B2, etc., is required. If a fault occurs in one transformer, the associated primary fuses blow and interrupts the service to just the load served by that transformer. Service cannot be restored to the loads normally served by the faulted transformer until the transformer is repaired or replaced. Cost of the primary selective secondary radial system is greater than that of the simple primary radial system of Figure 1.1-1 because of the additional primary main breakers, tie breaker, two-sources, increased number of feeder breakers, the use of primary-duplex or selector switches, and the greater amount of primary feeder cable required. The benets from the reduction in the amount of load lost when a primary feeder is faulted, plus the quick restoration of service to all

4. Two-Source Primary Secondary Selective System

This system uses the same principle of duplicate sources from the power supply point utilizing two primary main breakers and a primary tie breaker. The two primary main breakers and primary tie breaker being either manually or electrically interlocked to prevent closing all three at the same time and paralleling the sources. Upon loss of voltage on one source, a manual or automatic transfer to the alternate source line may be utilized to restore power to all primary loads. Each transformer secondary is arranged in a typical double-ended unit substation arrangement as shown in Figure 1.1-10. The two secondary main breakers and secondary tie breaker of each unit substation are again either mechanically or electrically interlocked to prevent parallel operation. Upon loss of secondary source voltage on one side, manual or automatic transfer may be utilized to transfer the loads to the other side, thus restoring power to all secondary loads. This arrangement permits quick restoration of service to all loads when a primary feeder or transformer fault occurs by opening the associated secondary main and closing the secondary tie breaker. If the loss of secondary voltage has occurred because of a primary feeder fault with the associated primary feeder breaker opening, then all secondary loads normally served by the faulted feeder would have to be transferred to the opposite primary feeder. This means each primary feeder conductor must be sized to carry the load on both sides of all the secondary buses it is serving under

Load Break Switches

Fuses

Figure 1.1-8. Duplex Fused Switch in Two Structures As an alternate to the duplex switch arrangement, a non-load break selector switch mechanically interlocked with a load break fused switch can be utilized as shown in Figure 1.1-9. The non-load break selector switch is physically located in the rear of the load break fused switch, thus only requiring one structure and a lower cost and oor space savings over the duplex arrangement. The non-load break switch is mechanically interlocked to prevent its operation unless the load break switch is opened. The main disadvantage of the selector switch is that conductors from both circuits are terminated in the same structure.

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-10 Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0030

Master TOC

i ii 1 2 3

secondary emergency transfer. If the loss of voltage was due to a failure of one of the transformers in the doubleended unit substation, then the associated primary fuses would open taking only the failed transformer out of service, and then only the secondary loads normally served by the faulted transformer would have to be transferred to the opposite transformer.

In either of the above emergency conditions, the in-service transformer of a double-ended unit substation would have to have the capability of serving the loads on both sides of the tie breaker. For this reason, transformers utilized in this application have equal kVA rating on each side of the doubleended unit substation and the normal operating maximum load on each transformer is typically about 2/3 base

nameplate kVA rating. Typically these transformers are furnished with fancooling and/or lower than normal temperature rise such that under emergency conditions they can carry on a continuous basis the maximum load on both sides of the secondary tie breaker. Because of this spare transformer capacity, the voltage regulation provided by the double-ended unit substation system under normal conditions is better than that of the systems previously discussed. The double-ended unit substation arrangement can be utilized in conjunction with any of the previous systems discussed which involve two primary sources. Although not recommended, if allowed by the utility, momentary re-transfer of loads to the restored source may be made closed transition (anti-parallel interlock schemes would have to be defeated) for either the primary or secondary systems. Under this condition, all equipment interrupting and momentary ratings should be suitable for the fault current available from both sources. For double-ended unit substations equipped with ground fault systems special consideration to transformer neutral grounding and equipment operation should be made see Grounding and Ground Fault Protection in Section 1.4. Where two single-ended unit substations are connected together by external tie conductors, it is recommended that a tie breaker be furnished at each end of the tie conductors.

52

52 52

Primary Main Breakers

4 5 6 7 8 9 10 11 12 13
K K Primary Fused Switch Transformer To Other Substations Typical Double-Ended Unit Substation 52 52

52

52

Primary Feeder Breakers

To Other Substations

Tie Breaker

Secondary Main Breaker

Figure 1.1-10. Two-Source Primary Secondary Selective System

5. Sparing Transformer System

K

14 15 16
K K Sparing Transformer

17 18 19
K K Typical Single-Ended Substation Typical Secondary Busway Loop

The sparing transformer system concept came into use as an alternative to the capital cost intensive double-ended secondary unit substation distribution system (see Two-Source Primary Secondary Selective System). It essentially replaces double-ended substations with single-ended substations and one or more sparing transformer substations all interconnected on a common secondary bus (see Figure 1.1-11).
Generally no more than 3 to 5 singleended substations are on a sparing loop. The essence of this design philosophy is that conservatively designed and loaded transformers are highly reliable electrical devices and rarely fail. Therefore, this design provides a single common backup transformer for a group of transformers in lieu of a backup transformer for each and every transformer. This system design still maintains a high degree of continuity of service.
CA08104001E

20 21
Figure 1.1-11. Sparing Transformer System

For more information visit: www.EatonElectrical.com

June 2006
Sheet 0031

TOC

Index

Power Distribution Systems System Design

1.1-11

Master TOC

Referring to Figure 1.1-11, it is apparent that the sparing concept backs up primary switch and primary cable failure as well. Restoration of lost or failed utility power is accomplished similarly to primary selective scheme previously discussed. It is therefore important to use an automatic throwover system in a two source lineup of primary switchgear to restore utility power as discussed in the Two-Source Primary scheme see Figure 1.1-10. A major advantage of the sparing transformer system is the typically lower total base kVA of transformation. In a double-ended substation design, each transformer must be rated to carry the sum of the loads of two busses and usually requires the addition of cooling fans to accomplish this rating. In the sparing concept, each transformer carries only its own load, which is typically not a fan-cooled rating. Major space savings is also a benet of this system in addition to rst cost savings. The sparing transformer system operates as follows: All main breakers, including the sparing main breaker are normally closed; the tie breakers are normally open. s Once a transformer (or primary cable or primary switch/fuse) fails, the associated secondary main breaker is opened. The associated tie breaker is then closed, which restores power to the single-ended substation bus. s Schemes which require the main to be opened before the tie is closed (open transition), and which allow any tie to be closed before the substation main is opened, (closed transition) are possible.
s

In facilities with no qualied electrical power operators, an open transition with key interlocking is often a prudent design.
Note: Each pair of main breaker/tie breaker key cylinders should be uniquely keyed to prevent any paralleled source operations.

Careful sizing of these transformers as well as careful specication of the transformers is required for reliability. Low temperature rise specied with continuous overload capacity or upgraded types of transformers should be considered. One disadvantage to this system is the external secondary tie system, see Figure 1.1-11. As shown, all singleended substations are tied together on the secondary with a tie busway or cable system. Location of substations is therefore limited because of voltage drop and cost considerations. Routing of busway, if used, must be carefully layed out. It should also be noted, that a tie busway or cable fault will essentially prevent the use of the sparing transformer until it is repaired. Commonly, the single-ended substations and the sparing transformer must be clustered. This can also be an advantage, as more kVA can be supported from a more compact space layout.

The major advantage of the secondary network system is continuity of service. No single fault anywhere on the primary system will interrupt service to any of the systems loads. Most faults will be cleared without interrupting service to any load. Another outstanding advantage that the network system offers is its exibility to meet changing and growing load conditions at minimum cost and minimum interruption in service to other loads on the network. In addition to exibility and service reliability, the secondary network system provides exceptionally uniform and good voltage regulation, and its high efciency materially reduces the costs of system losses. Three major differences between the network system and the simple radial system account for the outstanding advantages of the network. First, a network protector is connected in the secondary leads of each network transformer in place of, or in addition to, the secondary main breaker, as shown in Figure 1.1-12. Also, the secondaries of each transformer in a given location (spot) are connected together by a switchgear or ring bus from which the loads are served over short radial feeder circuits. Finally, the primary supply has sufcient capacity to carry the entire building load without overloading when any one primary feeder is out of service. A network protector is a specially designed heavy duty air power breaker, spring close with electrical motor-charged mechanism, with a network relay to control the status of the protector (tripped or closed). The network relay is usually a solid-state microprocessorbased component integrated

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

6. Simple Spot Network Systems

The ac secondary network system is the system that has been used for many years to distribute electric power in the high-density, downtown areas of cities, usually in the form of utility grids. Modications of this type of system make it applicable to serve loads within buildings.

With a closed transition scheme it is common to add a timer function that opens the tie breaker unless either main breaker is opened within a time interval. This closed transition allows power to be transferred to the sparing transformer without interruption, such as for routine maintenance, and then back to the substation. This closed transition transfer has an advantage in some facilities, however, appropriate interrupting capacities and bus bracing must be specied suitable for the momentary parallel operation.

Typical Feeder Primary Circuit Network Transformer Network Protector Fuses Optional Main, 50/51 Relaying and/or Network Disconnect To Other Networks

Tie NC

Tie NC Drawout Low Voltage Switchgear

18 19

LV Feeder

Customer Loads

Customer Loads

Customer Loads

20 21

Figure 1.1-12. Three-Source Spot Network

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-12 Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0032

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

into the protector enclosure which functions to automatically close the protector only when the voltage conditions are such that its associated transformer will supply power to the secondary network loads, and to automatically open the protector when power ows from the secondary to the network transformer. The purpose of the network protector is to protect the integrity of the network bus voltage and the loads served from it against transformer and primary feeder faults by quickly disconnecting the defective feeder-transformer pair from the network when backfeed occurs. The simple spot network system resembles the secondary-selective radial system in that each load area is supplied over two or more primary feeders through two or more transformers. In network systems, the transformers are connected through network protectors to a common bus, as shown in Figure 1.1-12, from which loads are served. Since the transformers are connected in parallel, a primary feeder or transformer fault does not cause any service interruption to the loads. The paralleled transformers supplying each load bus will normally carry equal load currents, whereas equal loading of the two separate transformers supplying a substation in the secondary-selective radial system is difcult to obtain. The interrupting duty imposed on the outgoing feeder breakers in the network will be greater with the spot network system. The optimum size and number of primary feeders can be used in the spot network system because the loss of any primary feeder and its associated transformers does not result in the loss of any load even for an instant. In spite of the spare capacity usually supplied in network systems, savings in primary switchgear and secondary switchgear costs often result when compared to a radial system design with similar spare capacity. This occurs in many radial systems because more and smaller feeders are often used in order to minimize the extent of any outage when a primary fault event occurs. In spot networks, when a fault occurs on a primary feeder or in a transformer, the fault is isolated from the system through the automatic tripping of the primary feeder circuit breaker and all of the network protectors associated

with that feeder circuit. This operation does not interrupt service to any loads. After the necessary repairs have been made, the system can be restored to normal operating conditions by closing the primary feeder breaker. All network protectors associated with that feeder will close automatically. The chief purpose of the network bus normally closed ties is to provide for the sharing of loads and a balancing of load currents for each primary service and transformer regardless of the condition of the primary services. Also, the ties provide a means for isolating and sectionalizing ground fault events within the switchgear network bus, thereby saving a portion of the loads from service interruptions, yet isolating the faulted portion for corrective action. The use of spot network systems provides users with several important advantages. First, they save transformer capacity. Spot networks permit equal loading of transformers under all conditions. Also, networks yield lower system losses and greatly improve voltage conditions. The voltage regulation on a network system is such that both lights and power can be fed from the same load bus. Much larger motors can be started acrossthe-line than on a simple radial system. This can result in simplied motor control and permits the use of relatively large low voltage motors with their less expensive control. Finally, network systems provide a greater degree of exibility in adding future loads; they can be connected to the closest spot network bus. Spot network systems are economical for buildings which have heavy concentrations of loads covering small areas, with considerable distance between areas, and light loads within the distances separating the concentrated loads. They are commonly used in hospitals, high rise ofce buildings, and institutional buildings where a high degree of service reliability is required from the utility sources. Spot network systems are especially economical where three or more primary feeders are available. Principally, this is due to supplying each load bus through three or more transformers and the reduction in spare cable and transformer capacity required.

They are also economical when compared to two transformer doubleended substations with normally opened tie breakers. Emergency power should be connected to network loads downstream from the network, or upstream at primary voltage, not at the network bus itself.

7. Medium Voltage Distribution System Design

A. Single Bus, Figure 1.1-13
The sources (utility and/or generator(s)) are connected to a single bus. All feeders are connected to the same bus.
Utility G

52 Main Bus

52

52

One of Several Feeders

Figure 1.1-13. Single Bus This conguration is the simplest system, however, outage of the utility results in total outage. Normally the generator does not have adequate capacity for the entire load. A properly relayed system equipped with load shedding, automatic voltage/ frequency control may be able to maintain partial system operation. Any future addition of breaker sections to the bus will require a shutdown of the bus, since there is no tie breaker.

B. Single Bus with Two-Sources from the Utility, Figure 1.1-14

Same as the single bus, except that two utility sources are available. This system is operated normally with the main breaker to one source open. Upon loss of the normal service the transfer to the standby Normally Open (NO) breaker can be automatic or manual. Automatic transfer is preferred for rapid service restoration especially in unattended stations.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0033

TOC

Index

Power Distribution Systems System Design

1.1-13

Master TOC

Utility #1

Utility #2

Normal

Standby

Again, the closing of the tie breaker can be manual or automatic. The statements made for the retransfer of scheme B apply to this scheme also.
Utility #1 Utility #2

The third tie breaker allows any bus to be fed from any utility source. Caution for Figures 1.1-14, 1.1-15 and 1.1-16: If continuous paralleling of sources is planned, reverse current, reverse power and other appropriate relaying protection should be added. When both sources are paralleled for any amount of time, the fault current available on the load side of the main device is the sum of the available fault current from each source plus the motor fault contribution. It is required that bus bracing, feeder breakers and all load side equipment is rated for the increased available fault current.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

52 NC

52 NO 52 NC Loads Bus #1 NO 52 Bus #2 52 NC

Figure 1.1-14. Single Bus with Two-Sources Retransfer to the Normal can be closed transition subject to the approval of the utility. Closed transition momentarily (5 10 cycles) parallels both utility sources. Caution: when both sources are paralleled, the fault current available on the load side of the main device is the sum of the available fault current from each source plus the motor fault contribution. It is recommended that the short circuit ratings of the bus, feeder breakers and all load side equipment are rated for the increased available fault current. If the utility requires open transfer, the disconnection of motors from the bus must be ensured by means of suitable time delay on reclosing as well as supervision of the bus voltage and its phase with respect to the incoming source voltage. This busing scheme does not preclude the use of cogeneration, but requires the use of sophisticated automatic synchronizing and synchronism checking controls, in addition to the previously mentioned load shedding, automatic frequency and voltage controls. This conguration is more expensive than the scheme shown in Figure 1.1-13, but service restoration is quicker. Again, a utility outage results in total outage to the load until transfer occurs. Extension of the bus or adding breakers requires a shutdown of the bus. If paralleling sources, reverse current, reverse power, and other appropriate relaying protection should be added as requested by the utility.
52 52

Summary
The medium voltage system congurations shown are based on using metalclad drawout switchgear. The service continuity required from electrical systems makes the use of single source systems impractical. In the design of a modern medium voltage system the engineer should: 1. Design a system as simple as possible. 2. Limit an outage to as small a portion of the system as possible. 3. Provide means for expanding the system without major shutdowns. 4. Relay the system so that only the faulted part is removed from service, and damage to it is minimized consistent with selectivity. 5. Specify and apply all equipment within its published ratings and national standards pertaining to the equipment and its installation.

Load

Load

Figure 1.1-15. Two-Source Utility with Tie Breaker If looped or primary selective distribution system for the loads is used, the buses can be extended without a shutdown by closing the tie breaker and transferring the loads to the other bus. This conguration is more expensive than B. The system is not limited to two buses only. Another advantage is that the design may incorporate momentary paralleling of buses on retransfer after the failed line has been restored to prevent another outage. See the Caution for Figures 1.1-14, 1.1-15 and 1.1-16. In Figure 1.1-16, closing of the tie breaker following the opening of a main breaker can be manual or automatic. However since a bus can be fed through two tie breakers the control scheme should be designed to make the selection.
Utility #1

Utility #2

Utility #3

16 17
52 NC NO 52 52 NC NO 52 52 NC

18 19

C. Multiple Sources with Tie Breaker, Figure 1.1-15 and Figure 1.1-16
This conguration is similar to conguration B. It differs signicantly in that both utility sources normally carry the loads and also by the incorporation of a normally open tie breaker. The outage to the system load for a utility outage is limited to half of the system.
CA08104001E

Bus #1

Bus #2

Bus #3

52 NO 52 Typical Feeder Tie Busway

52

52

52 NO

20 21

Figure 1.1-16. Triple-Ended Arrangement

For more information visit: www.EatonElectrical.com

1.1-14 Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0034

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11

Health Care Facilities

Health Care Facilities are dened by NFPA (National Fire Protection Agency) as Buildings or portions of buildings in which medical, dental, psychiatric, nursing, obstetrical, or surgical care are provided. Due to the critical nature of the care being provided at these facilities and their increasing dependence on electrical equipment for preservation of life, health care facilities have special requirements for the design of their electrical distribution systems. These requirements are typically much more stringent than commercial or industrial facilities. The following section summarizes some of the unique requirements of health care facility design. There are several agencies and organizations that develop requirements for health care electrical distribution system design. The following is a listing of some of the specic NFPA (National Fire Protection Agency) standards that affect health care facility design and implementation: NFPA 37 Standard for Stationary Combustion Engines and Gas Turbines. s NFPA 70 National Electrical Code. s NFPA 99 Health Care Facilities.
s

NFPA 101 Life Safety Code. NFPA 110 Standard for Emergency and Standby Power Systems. s NFPA 111 Standard on Stored Electrical Energy Emergency and Standby Power Systems.
s s

These NFPA guidelines represent the most industry recognized standard requirements for health care electrical design. However, the electrical design engineer should consult with the authorities having jurisdiction over the local region for specic electrical distribution requirements.

The electrical system requirements for the Essential Electrical System (EES) vary according to the type of health care facility. Health care facilities are categorized by NFPA 99 as Type 1, Type 2 or, Type 3 facilities. Some example health care facilities, classied by Type, are summarized in the following Table 1.1-8. Table 1.1-8. Health Care Facilities
Description Denition EES Type Hospitals NFPA 99 Chap. 13 Type 1 Nursing Homes NFPA 99 Chap. 17 Type 2 Limited Care Facilities NFPA 99 Chap. 18 Type 2 Ambulatory Surgical Facilities NFPA 99 Chap. 14 Type 3 Other Health Care Facilities NFPA 99 Chap. 14 Type 3 If electrical life support or critical care areas are present then facility is classied as Type 1.

Health Care Electrical System Requirements

Health care electrical systems usually consist of two parts: 1. Non-essential or Normal Electrical System. 2. Essential Electrical System. All electrical power in a health care facility is important, though some loads are not critical to the safe operation of the facility. These non-essential or normal loads include things such as general lighting, general lab equipment, non-critical service equipment, patient care areas, etc. These loads are not required to be fed from an alternate source of power.

Type 1 Essential Electrical Systems (EES)

Type 1 Essential Electrical Systems (EES) have the most stringent requirements for providing continuity of electrical service and will, therefore, be the focus of this section. Type 1 EES requirements meet or exceed the requirements for Type 2 and Type 3 facilities.

Normal Source

Normal Source

Normal Source

Emergency Power Supply G

12 13 14 15 16
Non-Essential Loads Non-Essential Loads

17 18 19 20 21
Manual Transfer Switch Delayed Automatic Transfer Switch Automatic (Non-Delaying) Transfer Switch Equipment System Life Safety Critical Branch Branch Emergency System Essential Electrical System

Figure 1.1-17. Typical Large Hospital Electrical System Type 1 Facility

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0035

TOC

Index

Power Distribution Systems System Design

1.1-15

Master TOC

Sources: Type 1 systems are required to have a minimum of two independent sources of electrical power. A normal source that generally supplies the entire facility and one or more alternate sources that supply power when the normal source is interrupted. The alternate source(s) must be an on-site generator driven by a prime mover unless a generator(s) exists as the normal power source. In the case where a generator(s) is utilized as the normal source, it is permissible for the alternate source to be a utility feed. Alternate source generators must be classied as Type 10, Class X, Level 1 gensets per NFPA 110 2-2 capable of providing power to the load in a maximum of 10 seconds. Typically, the alternate sources of power are supplied to the loads through a series of automatic and/or manual transfer switches. (See Section 25.) The transfer switches can be non-delayed automatic, delayed automatic, or manual transfer depending on the requirements of the specic branch of the EES that they are feeding. It is permissible to feed multiple branches or systems of the EES from a single automatic transfer switch provided that the maximum demand on the EES does not exceed 150 kVA. This conguration is typically seen in smaller health care facilities that must meet Type 1 EES requirements. (See Figure 1.1-18.)
Normal Source Alternate Source G

Table 1.1-9. Type 1 EES Applicable Codes

Description Design Sources Uses Emergency Power Supply Classication Distribution Standard NFPA 99 NFPA 99 NFPA 99 Section 4.4.1.1.1 4.4.1.1.4 thru 4.4.4.1.1.7.2 4.4.1.1.8 (1-3)

NFPA 110 NFPA 99 NEC

4 4.4.2 517-30

Systems and Branches of Service: The Type 1 EES consists of two separate power systems capable of supplying power considered essential for life safety and effective facility operation during an interruption of the normal power source. They are the Emergency System and the Equipment System. 1. Emergency System consists of circuits essential to life safety and critical patient care. The Emergency System is an electrical sub-system that must be fed from an automatic transfer switch or series of automatic transfer switches. This Emergency System consists of two mandatory branches that provide power to systems and functions essential to life safety and critical patient care. A. Life Safety Branch supplies power for lighting, receptacles, and equipment to perform the following functions: 1. 2. 3. 4. Illumination of means of egress. Exit signs and exit direction signs. Alarms and alerting systems. Emergency communications systems. 5. Task illumination, battery chargers for battery powered lighting, and select receptacles at the generator. 6. Elevator lighting control, communication and signal systems. 7. Automatic doors used for egress. These are the only functions permitted to be on the life safety branch. Life Safety Branch equipment and wiring must be entirely independent of all other loads and branches of service. This includes separation of raceways, boxes or cabinets. Power must be supplied to the Life Safety Branch from a non-delayed automatic transfer switch.

B. Critical Branch supplies power for task illumination, xed equipment, selected receptacles and selected power circuits for areas related to patient care. The purpose of the critical branch is to provide power to a limited number of receptacles and locations to reduce load and minimize the chances of fault conditions. The transfer switch(es) feeding the critical branch must be automatic type. They are permitted to have appropriate time delays that will follow the restoration of the life safety branch but should have power restored within 10 seconds of normal source power loss. The critical branch provides power to circuits serving the following areas and functions: 1. Critical care areas. 2. Isolated Power Systems in special environments. 3. Task illumination and selected receptacles in the following patient care areas: infant nurseries, medication prep areas, pharmacy, selected acute nursing areas, psychiatric bed areas, ward treatment rooms, nurses stations. 4. Specialized patient care task illumination, where needed. 5. Nurse call systems. 6. Blood, bone and tissue banks. 7. Telephone equipment rooms and closets. 8. Task illumination, selected receptacles, and selected power circuits for the following: general care beds (at least one duplex receptacle), angiographic labs, cardiac catheterization labs, coronary care units, hemodialysis rooms, selected emergency room treatment areas, human physiology labs, intensive care units, selected postoperative recovery rooms. 9. Additional circuits and singlephase fraction motors as needed for effective facility operation.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Non-Essential Loads Entire Essential Electric System (150 kVA or Less)

Figure 1.1-18. Small Hospital Electrical System Single EES Transfer Switch

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-16 Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0036

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Table 1.1-10. Type 1 Emergency System Applicable Codes

Description General Life Safety Branch Critical Branch Wiring Standard NFPA 99 NEC NFPA 99 NEC NFPA 99 NEC NFPA 99 NEC Section 4.4.2.2.2 517-31 4.4.2.2.2.2 517-32 4.4.2.2.2.3 517-33 4.4.2.2.4 517-30(c)

The following equipment must be arranged for delayed automatic or manual transfer to the emergency power supply: 1. Select heating equipment. 2. Select elevators. 3. Supply, return and exhaust ventilating systems for surgical, obstetrical, intensive care, coronary care, nurseries, and emergency treatment areas. 4. Supply, return and exhaust ventilating systems for airborne infectious/isolation rooms, labs and medical areas where hazardous materials are used. 5. Hyperbaric facilities. 6. Hypobaric facilities. 7. Autoclaving equipment. 8. Controls for equipment listed above. 9. Other selected equipment in kitchens, laundries, radiology rooms, and central refrigeration as selected. Table 1.1-11. Type 1 Equipment System Applicable Codes
Description General Equipment Standard NFPA 99 NEC NFPA 99 NEC Section 4.4.2.2.3 517-34 4.4.2.2.3 (3-5) 517-34(a)-(b)

must be congured such that the loads will not cause the generator to overload and must be shed in the event the generator enters an overload condition. Ground Fault Protection per NFPA 70 NEC article 230-95, ground fault protection is required on any feeder or service disconnect 1000 A or larger on systems with line to ground voltages of 150 volts or greater and phase-to-phase voltages of 600 volts or less. For health care facilities (of any type), a second level of ground fault protection is required to be on the next level of feeder downstream. This second level of ground fault is only required for feeders that serve patient care areas and equipment intended to support life. 100% selective coordination of the two levels of ground fault protection must be achieved with a minimum six-cycle separation between the upstream and downstream device. NEC 517-17 prohibits the installation of ground fault protection between the on-site generator(s) and any EES transfer switch or on the load side of a transfer switch feeding EES circuits. (See Figure 1.1-19 Additional Level of Ground Fault). The intent of this code section is to prevent a ground fault that causes a trip on the normal system to also cause a trip on the emergency system. Such an event could result in complete power loss of both normal and emergency power sources and could not be recovered until the source of the ground fault was located and isolated from the system. To prevent this condition, NEC 700-26 removes the

2. Equipment System consists of major electrical equipment necessary for patient care and Type 1 operation. The Equipment System is a subsystem of the EES that consists of large electrical equipment loads needed for patient care and basic hospital operation. Loads on the Equipment System that are essential to generator operation are required to be fed by a non-delayed automatic transfer switch. The following equipment must be arranged for delayed automatic transfer to the emergency power supply: 1. Central suction systems for medical and surgical functions. 2. Sump pumps and other equipment required for the safe operation of a major apparatus. 3. Compressed air systems for medical and surgical functions. 4. Smoke control and stair pressurization systems. 5. Kitchen hood supply and exhaust systems, if required to operate during a re.
Normal Source

Any loads served by the generator that are not approved as outlined above as part of the Essential Electrical System must be connected through a separate transfer switch. These transfer switches
Normal Source(s)

G Generator Breakers are Typically Supplied with Ground Fault Alarm Only. (NEC 700-26) Additional Level of Ground Fault is not Permitted Between Generator and EES Transfer Switches. (NEC 517-17a(1))

480/277 V

480/277 V 1000 A Service GF or Larger Entrance

480/277 V 1000 A Service GF or Larger Entrance

15 16 17 18 19 20

1000 A Service GF or Larger Entrance

GF GF GF GF GF

Additional Level of Ground Fault Protection

GF GF GF

GF GF GF

Non-Essential Loads

Non-Essential Loads

GF = Ground Fault Protection Required Essential Electrical System

Additional Level of Ground Fault is not Permitted on Load Side of EES Transfer Switches. (NEC 517-17a(2))

Figure 1.1-19. Additional Level of Ground Fault Protection

21

Ground fault protection is required for service disconnects 1000 amperes and larger or systems with less than 600 volts phase-to-phase and greater than 150 volts to ground per NEC 230-95.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0037

TOC

Index

Power Distribution Systems System Design

1.1-17

Master TOC

ground fault protection requirement for the emergency system source. Typically, the emergency system generator(s) are equipped with ground fault alarms that do not automatically disconnect during a ground fault. Table 1.1-12. Ground Fault Protection Applicable Codes
Description Services Feeders Additional Level Alternate Source Standard NEC NEC NEC NFPA 99 NEC NEC Section 230-95 215-10 517-17 4.3.2.5 700-26 700-7 (d)

Maintenance and Testing

Regular maintenance and testing of the electrical distribution system in a health care facility is necessary to ensure proper operation in an emergency and, in some cases, to maintain government accreditation. Any health care facility receiving Medicare or Medicaid reimbursement from the government must be accredited by the Joint Commission on Accreditation of Health Care Organizations (JCAHO). JCAHO has established a group of standards called the Environment of Care, which must be met for health care facility accreditation. Included in these standards is the regular testing of the emergency (alternate) power system(s). The emergency power system must be tested in accordance with NFPA 110 Standard for Emergency and Standby Power Systems guidelines at intervals not less than 20 days and not exceeding 40 days. Generators must be tested for a minimum of 30 minutes under the criteria dened in NFPA 110. One method to automate the task of monthly generator tests is through the use of PowerNet communications. With the PowerNet integrated metering, monitoring and control system, a facility maintenance director can initiate a generator test, control/monitor loads, meter/monitor generator test points and create a JCAHO compliant report automatically from a central PC. The report contains all metered values, test results, date/time information, etc. necessary to satisfy JCAHO requirements. This automated generator testing procedure reduces the labor, training and inaccuracies that occur during manual emergency power system tests. (See Power Monitoring Section 2.) Table 1.1-14. Maintenance and Testing Applicable Codes
Description Grounding Emergency Power System Generator Transfer Switches Breakers Standard NFPA 99 NFPA 99 JCAHO NFPA 110 NFPA 110 NFPA 99 NFPA 110 Section 4.3.3.1 4.4.4.1.1 EC.2.14(d) 8.4.2 8.4.5 4.4.4.1.2 8.4.6

trained in development and execution of annual preventative maintenance procedures of health care facility electrical distribution systems.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Paralleling Emergency Generators

Without Utility Paralleling
In many health care facilities (and other large facilities with critical loads), the demand for standby emergency power is large enough to require multiple generator sets to power all of the required Essential Electrical System (EES) loads. In many cases, it becomes more exible and easier to operate the required multiple generators from a single location utilizing Generator Paralleling Switchgear. Figure 1.1-20 on Page 1.1-18 shows an example of a typical one-line for a paralleling switchgear lineup feeding the EES. A typical abbreviated sequence of operation for a multiple emergency generator and ATS system follows. Note that other modes of operation such as generator demand priority and automated testing modes are available but are not included below. (Reference Section 43 for complete detailed sequences of operation.) 1. Entering Emergency Mode a. Upon loss of normal source, automatic transfer switches send generator control system a run request. b. All available generators are started. The rst generator up to voltage and frequency is closed to the bus. c. Unsheddable loads and Load Shed Priority 1 loads are powered in less than 10 seconds. d. The remaining generators are synchronized and paralleled to the bus as they come up to voltage and frequency. e. As additional generators are paralleled to the emergency bus, Load Shed Priority levels are added, powering their associated loads. f. The system is now in Emergency Mode. 2. Exit from Emergency Mode a. Automatic transfer switches sense the utility source is within acceptable operational tolerances for a time duration set at the automatic transfer switch.

Wet Locations A wet location in a health care facility is any patient care area that is normally subject to wet conditions while patients are present. Typical wet locations can include operating rooms, anesthetizing locations, dialysis locations, etc. (Patient beds, toilets, sinks, are not considered wet locations.) These wet locations require special protection to guard against electric shock. The ground fault current in these areas must be limited not to exceed 6 mA. In areas where the interruption of power is permissible, ground fault circuit interrupters (GFCI) can be employed. GFCIs will interrupt a circuit when ground fault current exceeds the present level (typically 2-5 mA). In areas where the interruption of power cannot be tolerated, protection from ground fault currents is accomplished through the use of an Isolated Power System. Isolated Power Systems provide power to an area that is isolated from ground (or ungrounded). This type of system limits the amount of current that ows to ground in the event of a single line-to-ground fault and maintains circuit continuity. Electronic Line Isolation Monitors (LIM) are used to monitor and display leakage currents to ground. When leakage current thresholds are exceeded, visible and/or audible alarms are initiated to alert occupants of a possible hazardous condition. This alarm occurs without interrupting power to allow for the safe conclusion of critical procedures. Table 1.1-13. Wet Location Applicable Codes
Description General Isolated Power Systems Standard NFPA 99 NEC NFPA 99 NEC Section 4.3.2.2.9 517-20 4.3.2.6 517-160

Routine maintenance should be performed on circuit breakers, transfer switches, switchgear, generator equipment, etc. by trained professionals to ensure the most reliable electrical system possible. See Section 43 for Eaton - Electrical Services & Systems E-ESS), which provides engineers,

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-18 Power Distribution Systems System Design

TOC

Index

June 2006
Sheet 0038

Master TOC

i ii 1 2 3 4 5 6 7

b. As each automatic transfer switch transfers back to utility power, it removes its run request from the generator plant. c. When the last automatic transfer switch has retransferred to the utility and all run requests have been removed from the generator plant, all generator circuit breakers are opened. d. The generators are allowed to run for their programmed cool- down period. e. The system is now back in Automatic/Standby Mode.

With Utility Paralleling

Today, many utilities are offering their customers excellent nancial incentives to utilize their onsite generation capacity to remove load from the utility grid. These incentives are sometimes referred to as Limited Interruptible Rates (LIP). Under these incentives, utilities will greatly reduce or eliminate kWhr or kW Demand charges to their customers with onsite generation capabilities. In exchange, during times of peak loading of the utility grid, the utility can ask their LIP rate customers to drop load from the grid by utilizing their onsite generation capabilities. Health care facilities are ideally suited to take advantage of these programs because they already have signicant onsite generation capabilities due to the Code requirements described.

Many health care facilities are taking advantage of these utility incentives by adding generator capacity over and above the NFPA requirements. Figure 1.1-21 on Page 1.1-19 shows an example one-line of a health care facility with complete generator backup and utility interconnect. NFPA 110 requirements state that the normal and emergency sources must be separated by a re rated wall. The intent of this requirement is so that a re in one location cannot takeout both sources of power. To meet this requirement, the Paralleling Switchgear must be split into separate sections with a tie bus through a re rated wall. For more information on Generator Paralleling Switchgear, see Section 43.

Utility Transformer

Generators X = Number of Units Utility Metering Typical Generator Breaker G1 G2 Gx

8 9 10 11 12 13 14 15 16 17
Non-Essential Loads

Service Main

Normal Bus Optional Electrically Operated Stored Energy Breakers

Emergency Bus Optional Electrically Operated Stored Energy Breakers F1 F2 Fx EF1 EF2 EFx

Equipment ATS # 1

Life Safety ATS # 2

Critical ATS # X

Load Shed/Load Add ATS Units

EP1

EP2

Typical Panelboards

EPX

Optional Closed Transition Paralleling of Generators and Utility

Figure 1.1-20. Typical One-Line for a Paralleling Switchgear Line-up Feeding the Essential Electrical System (EES)

18 19 20 21
For more information visit: www.EatonElectrical.com CA08104001E

June 2006
Sheet 0039

TOC

Index

Power Distribution Systems System Design

1.1-19

Master TOC

Utility Transformer

Fire Rated Wall or Separation Barrier Generators X = Number of Units

i ii 1 2 3
Emergency Bus

Utility Metering Utility Protective Relay Service Main Normal Bus Closed Transition Paralleling of Generators and Utility, Plus Soft Loading/ Unloading TIE Optional Electrically Operated Stored Energy Breakers Typical Generator Breaker

G1

G2

Gx

Optional TIE Electrically Operated Stored Energy Breakers EF1 EF2 EFx

4 5 6

F1

F2

Fx

Field Installed Cable or Busway

Non-Essential Loads EP1

Equipment ATS # 1

Life Safety ATS # 2

Critical ATS # X

Load Shed/ Load Add ATS Units

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

EP2

EPX

Typical Panelboards

Figure 1.1-21. Typical One-Line Health Care Facility with Complete Generator Backup and Utility Interconnect

CA08104001E

For more information visit: www.EatonElectrical.com

1.1-20 Power Distribution Systems

TOC Index

June 2006
Sheet 0040

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

This page intentionally left blank.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0041

TOC

Index

Power Distribution Systems Generator System Design

1.2-1

Master TOC

Generators and Generator Systems

Types of Engines
Many generator sets are relatively small in size, typically ranging from several kilowatts to several megawatts. These units are often required to come on line and operate quickly. They need to have the capacity to run for an extended period of time. The internal combustion engine is an excellent choice as the prime mover for the majority of these applications. Turbines may also be utilized. Diesel fueled engines are the most common, but other fuels used include natural gas, digester gas, landll gas, propane, biodiesel, crude oil, steam and others. Some campuses and industrial facilities use and produce steam for heating and other processes. These facilities may nd it economically feasible to produce electricity as a by-product of the steam production. These installations would typically be classied as a cogeneration facility producing a fairly constant power output and operating in parallel with the electric utility system.

Types of Generators
Generators can be either synchronous or asynchronous. Asynchronous generators are also referred to as induction generators. The construction is essentially the same as an induction motor. It has a squirrel-cage rotor and wound stator. An induction generator is a motor driven above its designed synchronous speed thus generating power. It will operate as a motor if it is running below synchronous speed. The induction generator does not have an exciter and must operate in parallel with the utility or another source. The induction generator requires vars from an external source for it to generate power. The induction generator operates at a slip frequency so its output frequency is automatically locked in with the utility's frequency. An induction generator is a popular choice for use when designing cogeneration systems, where it will operate in parallel with the utility. This type of generator offers certain advantages over a synchronous generator. For example, voltage and frequency are controlled by the utility; thus voltage and frequency regulators are not required. In addition, the generator construction offers high reliability and little maintenance. Also, a minimum of protective relays and controls are required. Its major disadvantages are that it requires vars from the system and it normally cannot operate as a standby/emergency generator. Synchronous generators, however, are the most common. Their output is determined by their eld and governor controls. Varying the current in the dc eld windings controls the voltage output. The frequency is controlled by the speed of rotation. The torque applied to the generator shaft by the driving engine controls the power output. In this manner, the synchronous generator offers precise control over the power it can generate. In cogeneration applications, it can be used to improve the power factor of the system.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Typical Diesel Genset Caterpillar

Introduction
The selection and application of generators into the electrical distribution system will depend on the particular application. There are many factors to consider including code requirements, environmental constraints, fuel sources, control complexity, utility requirements and load requirements. The Health Care Requirements for legally required emergency standby generation systems are described starting on Page 1.1-14. Systems described in this section are applicable to Health Care requirements, as well as other facilities that may require a high degree of reliability. The electrical supply for data centers, nancial institutions, telecommunications, government and public utilities also require high reliability. Threats of disaster or terror attacks have prompted many facilities to require complete self-sufciency for continuous operation.

CA08104001E

For more information visit: www.EatonElectrical.com

1.2-2

Power Distribution Systems Generator System Design

TOC

Index

June 2006
Sheet 0042

Master TOC

i ii 1 2 3 4 5 6 7 8

Generator Systems
Emergency Standby Generator System
There are primarily three types of generator systems. The rst and simplest type is a single generator that operates independently from the electric utility power grid. This is typically referred to as an Emergency Standby Generator System. Figure 1.2-1 shows a single standby generator, utility source and a transfer switch. In this case, the load is either supplied from the utility or the generator. The generator and the utility are never continuously connected together. This simple radial system has few requirements for protection and control. It also has the least impact on the complete electric power distribution system. It should be noted that this type of generator system improves overall electrical reliability but does not provide the redundancy that some facilities require if the generator fails to start or is out for maintenance.

Multiple Isolated Standby Generators

The second type of generator system is a multiple isolated set of standby generators. Figure 1.2-2 shows multiple generators connected to a paralleling bus feeding multiple transfer switches. The utility is the normal source for the transfer switches. The generators and the utility are never continuously connected together in this scheme. Multiple generators may be required to meet the load requirements (N system). Generators may be applied in an N+1 or a 2N system for improved system reliability.

Multiple generator systems have a more complex control and protection requirement as the units have to be synchronized and paralleled together. The generators are required to share the load proportionally without swings or prolonged hunting in voltage or frequency for load sharing. They may also require multiple levels of load shedding and/or load restoration schemes to match generation capacity.

Multiple Generators Operating in Parallel with Utility System

The third type of system is either one with a single or multiple generators that operate in parallel with the utility system. Figure 1.2-3 shows two generators and a utility source feeding a switchgear lineup feeding multiple loads. This system typically requires generator capacity sufcient to carry the entire load or sophisticated load shedding schemes. This system will require a complete and complex protection and control scheme. The electric utility may have very stringent and costly protection requirements for the system. IEEE standard 1547 describes the interconnection requirements for paralleling to the utility.
Utility G1 G2

Utility G1 G2

Switchgear

ATS-1

ATS-2

Load 1

Load 2

Utility

9 10 11
ATS

G1

Figure 1.2-2. Multiple Isolated Set of Standby Generators In an N system, where N is the number of generators required to carry the load; if a generator fails or is out for maintenance, then the load may be dropped. This is unacceptable for most critical 24/7 operations. In an N + 1 system, N is the number of generators needed to carry the load and 1 is an extra generator for redundancy. If one generator fails to start or is out for maintenance, it will not affect the load. In a 2N system, there is complete 100% redundancy in the standby generation system such that the failure of one complete set of generators will not affect the load.

Switchgear

12 13 14 15 16 17 18 19 20 21
Load

Load 1

Load 2

Load 3

Figure 1.2-1. Emergency Standby Generator System

Figure 1.2-3. Multiple Generators Operating in Parallel with Utility System

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0043

TOC

Index

Power Distribution Systems Generator System Design

1.2-3

Master TOC

Generator Fundamentals
A generator consists of two primary components, a prime mover and an alternator. The prime mover is the energy source used to turn the rotor of the alternator. It is typically a diesel combustion engine for most emergency or standby systems. In cogeneration applications, the prime mover may come from a steam driven turbine or other source. On diesel units, a governor and voltage regulator are used to control the speed and power output. The alternator is typically a synchronous machine driven by the prime mover. A voltage regulator controls its voltage output by adjusting the eld. The output of a single generator or multiple paralleled generator sets is controlled by these two inputs. The alternator is designed to operate at a specied speed for the required output frequency, typically 60 or 50 hertz. The voltage regulator and engine governor along with other systems dene the generators response to dynamic load changes and motor starting characteristics. Generators are rated in power and voltage output. Most generators are designed to operate at a 0.8 power factor. For example, a 2000 kW generator at 277/480 V would have a kVA rating of 2500 kVA (2000 kW/ 08 pf) and a continuous current rating of 3007 A ( 2500 kVA 480V 3 ). Typical synchronous generators for industrial and commercial power systems range in size from 100 to 3,000 kVA and from 208 V to 13,800 V. There are other ratings available and these discussions are applicable to those ratings as well. Generators must be considered in the short circuit and coordination study as they may greatly impact the rating of the electrical distribution system. This is especially common on large installations with multiple generators and systems that parallel with the utility source. Short circuit current contribution from a generator typically ranges from 8 to 12 times full load amperes.

The application of generators requires special protection requirements. The size, voltage class, importance and dollar investment will inuence the protection scheme associated with the generator(s). Mode of operation will inuence the utility company's interface protection requirements. Paralleling with the electric utility is the most complicated of the utility inter-tie requirements. IEEE ANSI 1547 provides recommended practices.

need to be switched for 4-wire loads or ground fault relays could misoperate and unbalanced neutral current may be carried on ground conductors. An IEEE working group has studied the practice of low resistance grounding of medium voltage generators within the general industry. This working group found that, for internal generator ground faults, the vast majority of the damage is done after the generator breaker is tripped off-line and the eld and the turbine is tripped. This is due to the stored energy in the generator ux that takes several seconds to dissipate after the generator is tripped offline. It is during this time that the Low Resistance Ground contributes huge energy over time into the generator ground fault. One of the solutions set forth by this working group is a Hybrid High Resistance Grounding (HHRG) scheme as shown in Figure 1.2-4. In the HHRG scheme, the Low Resistance Ground (LRG) is quickly tripped off-line when the generator protection senses the ground fault. The LRG is cleared at the same time that the generator breaker clears leaving the High Resistance Ground portion connected to control the transient overvoltages during the coast-down phase of the generator thereby all but eliminating generator damage.

i ii 1 2 3 4 5 6 7 8 9 10 11

Generator Grounding
Generator grounding methods need to be considered and may affect the distribution equipment and ratings. Generators may be connected in delta or wye but wye is the most typical connection. A wye-connected generator can be solidly grounded, low impedance grounded, high impedance grounded or ungrounded. Section 1.4 discusses general grounding schemes, benets of each and protection considerations. A solidly grounded generator may have a lower zero sequence impedance than its positive sequence impedance. In this case, the equipment will need to be rated for the larger available ground fault current. The generator ground can be the same as the system ground or it could be a separate ground. If they are separate grounds, then the neutral will

HRG 51G Gen Phase Relays 87GN 86 R R LRG 59G

12 13 14 15

Figure 1.2-4. Hybrid High Resistance Grounding Scheme

16 17 18 19 20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.2-4

Power Distribution Systems Generator System Design

TOC

Index

June 2006
Sheet 0044

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Generator Controls
The engine generator set has controls to maintain the output frequency (speed) and voltage. These controls consist of a governor and voltage regulator. As loads change on the system the frequency and voltage will change. The speed control will then adjust the governor to correct for the load (kW) change. The voltage regulator will change the eld current to adjust the voltage to the desired voltage value. These are the basic controls found on all synchronous generators. Multiple generator systems require more sophisticated controls. Generators are paralleled in a multi-generator system and they must share the load. These systems often have a load shed scheme, which adds to the complexity. Multiple generator schemes need a master controller to prevent units from being connected out of phase. The sequence of operation is to send a start signal to all generators simultaneously. The rst unit up to frequency and voltage will be permitted to close its respective breaker and energize the paralleling bus. Breakers for the other generators are held open, not permitted to close, until certain conditions are met. Once the paralleling bus is energized the remaining generators must be synchronized to it before the generators can be paralleled. Synchronization compares the voltage phasors angle and magnitude. Both generators must be operating at the same frequency and lined up within typically 5 to 10 degrees with each other. The voltage magnitude typically must be within 20 to 24%. A synch-scope is typically supplied on paralleling gear. The synch-scope displays the relative relationship between voltage phasors on the generator to be paralleled and the bus. If the generator is running slower than the bus (less than 60 Hz) then the needle on the scope will spin in the counterclockwise direction. If it is running faster then it will rotate in the clockwise direction. The greater the frequency difference, the faster is the rotation. It is important that the generators are in phase before they are paralleled. Severe damage will occur if generators are paralleled out-of-phase.

Generator Short Circuit Characteristics

If a short circuit is applied directly to the output terminals of a synchronous generator it will produce an extremely high current initially; gradually decaying to a steady state value. This change is represented by a varying reactive impedance. There are three specic reactance's used for short circuit fault currents. They are:
s

Subtransient reactance Xd which is used to determine the fault current during the rst 1 to 5 cycles. s Transient reactance Xd which is used to determine the fault current during the next 5 to 200 cycles. s Synchronous reactance Xd which is used to determine the steady state fault current. The subtransient reactance Xd will range from a minimum of approximately 9% for a two pole round rotor machine to approximately 32% for a low speed salient pole hydro-generator. The initial symmetrical fault current can be as much as 12 times full load current. Depending on the generator type, the zero sequence impedance may be less than the subtransient reactance and the ground fault current substantially higher than the three phase short circuit current. For example, a 2500 kVA, 480/277 V, 4 pole, 2/3rds pitch stand-by generator has a 0.1411 per unit subtransient reactance Xd and a 0.033 per unit zero sequence Xo reactance. The ground current is approximately a third larger than the three-phase fault current. The ground fault current can be reduced to the three-phase level by simply adding a small reactance between the generator neutral and ground while still being considered solidly grounded. The electric power system analysis must be performed based on the worst case operating conditions. Typically this is when all sources are paralleled. If the system can operate with both the utility supply and generators in parallel then the equipment must be rated for the combined fault current plus motor contribution. If the generator and utility will not be paralleled, then both cases will need to be looked at independently and the worst case used for selecting the equipment ratings.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0045

TOC

Index

Power Distribution Systems Generator System Design

1.2-5

Master TOC

Generator Protection
Generator protection will vary and depend on the size of the generator, type of system and importance of the generator. Generator sizes are dened as: small 1000 kVA maximum up to 600 V (500 kVA maximum when above 600 V); medium over 1000 kVA to 12,500 kVA maximum regardless of voltage; large from 12,500 50,000 kVA. The simplest is a single generator system used to feed emergency and/or standby loads. In this case, the generator is the only source available when it is operating and it must keep operating until the normal source returns. Figure 1.2-5 Part (A) shows minimum recommended protection for a single generator used as an emergency or standby system. Phase and ground time overcurrent protection (Device 51 and 51G) will provide protection for external faults. For medium voltage generators, a voltage controlled time overcurrent relay (Device 51V) is recommended for the phase protection as it can be set more sensitive than standard overcurrent relays and is less likely to false operate on normal overloads. This scheme may not provide adequate protection for internal generator faults when no other power source exists. Local generator controllers may offer additional protection for voltage and frequency conditions outside the generators capabilities. Figure 1.2-5 Part (B) shows the recommended protection for multiple isolated medium voltage small generators. Additional protection may be desired and could include generator differential, reverse power and loss of eld protection. Differential protection (Device 87) can be accomplished with either a self-balancing set of CTs as in Figure 1.2-6 or with a percentage differential scheme as in Figure 1.2-7 on Page 1.2-6. The percentage differential scheme offers the advantage of reducing the possibility for false tripping due to CT saturation. The self-balancing scheme offers the advantages increased sensitivity; needing three current transformers in lieu of six and the elimination of current transformer external wiring from the generator location to the generator switchgear location.
Generator Protection ANSI/IEEE Std 242-1986

i ii

1 51 Alternate Location

1 51V

1 32

1 40

1 2

1 Gen 1 51 Preferred Location Gen 51G

3 87

3 4 5

1 51G

(A)

(A) Single Isolated Generator on Low Voltage System (B) Multiple Isolated Generator on Medium Voltage System

(B)

6 7

Figure 1.2-5. Typical Protective Relaying Scheme for Small Generators

8
R

9 10 11 12 13 14

50/5A

87-1

50/5A

87-2

50/5A

87-3

Gen

15 16
Figure 1.2-6. Self-Balancing Generator Differential Relay Scheme

17 18 19 20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.2-6

Power Distribution Systems Generator System Design

TOC

Index

June 2006
Sheet 0046

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Reverse power protection (Device 32) is used to prevent the generator from being motored. Motoring could damage (with other hazards) the prime mover. A steam turbine could overheat and fail. A diesel or gas engine could either catch re or explode. A steam turbine can typically withstand approximately 3% reverse power where a diesel engine can withstand up to 25% reverse power. Loss of eld protection (Device 40) is needed when generators are operating in parallel with one another or the power grid. When a synchronous generator loses its eld, it will continue to generate power as an induction generator obtaining its excitation from the other machines on the system. During this condition, the rotor will quickly overheat due to the slip frequency currents induced in it. Loss of excitation in one machine could jeopardize the operation of the other machines beyond their capability and the entire system.

Grounding Resistor 51G

87 01 PC R1 R1 02 Gen OC R2 03 87G R3 R3 R2

52

To Main Bus

OC = Operating Coil PC = Permissive Coil

Figure 1.2-7. Generator Percentage Differential Relay (Phase Scheme) and Ground Differential Scheme Using a Directional Relay

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0047

TOC

Index

Power Distribution Systems Generator System Design

1.2-7

Master TOC

Typical protection for larger generators is shown in Figure 1.2-8. It adds phase unbalance and eld ground fault protection. Phase unbalance (Device 46) or negative sequence overcurrent protection prevents the generators from rotor overheating damage. Unbalanced loads, fault conditions or open phasing will produce a negative sequence current to ow. The unbalanced currents induce double system frequency currents in the rotor, which quickly causes rotor overheating. Serious damage will occur to the generator if the unbalance is allowed to persist.
3 1 87

i
3 87B 81U/O

ii 1
27/59

2
3 51V 1 40 1 32 1 46

3 4

Other protection functions such as under/over voltage (Device 27/59) could be applied to any size generator. The voltage regulator typically maintains the output voltage within its desired output range. This protection can provide backup protection in case the voltage regulator fails. Under/over frequency protection (Device 81U/81O) could be used for backup protection for the speed control. Synch check relays (Device 25) are typically applied as a breaker permissive close function where generators are paralleled. Many modern protective relays are microprocessor-based and provide a full complement of generator protection functions in a single package. The cost per protection function has been drastically reduced such that it is feasible to provide more complete protection even to smaller generators. IEEE ANSI 1547 provides recommended practices for utility inter-tie protection. If the system has closed transition or parallel capability, additional protection may be required by the utility. Typically, no additional protection is required if the generator is paralleled to the utility for a maximum of 100 msec or less. Systems that offer soft transfer, peak shaving or co-generation will require additional utility inter-tie protection. The protection could include directional overcurrent and power relays and even transfer trip schemes. Please consult your local utility for specic requirements.

87G

60 Voltage Regulator and Metering Circuits 1 1 49 64

5 6 7

Gen E

8
51G

9 10 11

Figure 1.2-8. Typical Protective Relaying Scheme for Large Generator

12 13 14 15 16 17 18 19 20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.2-8

Power Distribution Systems Generator System Design

TOC

Index

June 2006
Sheet 0048

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Generator Set Sizing and Ratings

Many factors must be considered when determining the proper size or electrical rating of an electrical power generator set. The engine or prime mover is sized to provide the actual or real power in kW, as well as speed (frequency) control through the use of an engine governor. The generator is sized to supply the kVA needed at startup and during normal running operation and it also provides voltage control using a brushless exciter and voltage regulator. Together the engine and generator provide the energy necessary to supply electrical loads in many different applications encountered in todays society. The generator set must be able to supply the starting and running electrical load. It must be able to pick up and start all motor loads and low power factor loads, and recover without excessive voltage dip or extended recovery time. Non-linear loads like variable frequency drives, uninterruptible power supply (UPS) systems and switching power supplies also require attention because the SCR switching causes voltage and current waveform distortion and harmonics. The harmonics generate additional heat in the generator windings and the generator may need to be upsized to accommodate this. The type of fuel (diesel, natural gas, propane etc.) used is important as it is a factor in determining generator set transient response. It is also necessary to determine the load factor or average power consumption of the generator set. This is typically dened as the load (kW) x time (hrs. while under that particular load) / total running time. When this load factor or average power is taken into consideration with peak demand requirements and the other operating parameters mentioned above, the overall electrical rating of the genset can be determined. Other items to consider include the unique installation, ambient and site requirements of the project. These will help to determine the physical conguration of the overall system.

Typical rating denitions for diesel gensets are: standby, prime plus 10, continuous and load management (paralleled with or isolated from utility). Any diesel genset can have several electrical ratings depending on the number of hours of operation per year and the ratio of electrical load/genset rating when in operation. The same diesel genset can have a standby rating of 2000 kW at 0.8 power factor (pf) and a continuous rating of 1825 kW at 0.8 pf. The lower continuous rating is due to the additional hours of operation and higher load that the continuous genset must carry. These additional requirements put more stress on the engine and generator and therefore the rating is decreased to maintain longevity of the equipment. Different generator set manufacturers use basically the same diesel genset electrical rating denitions and these are based on international diesel fuel stop power standards from organizations like ISO, DIN and others. A standby diesel genset rating is typically dened as supplying varying electrical loads for the duration of a power outage with the load normally connected to utility, genset operating < 100 hours per year and no overload capability. A prime plus 10 rating is typically dened as supplying varying electrical loads for the duration of a power outage with the load normally connected to utility, genset operating 500 hours per year and overload capability of 10% above its rating for one hour out of twelve. A continuous rating is typically dened as supplying unvarying electrical loads (i.e., base loaded) for an unlimited time. The load management ratings apply to gensets in parallel operation with the utility or isolated/islanded from utility and these ratings vary in usability from < 200 hours per year to unlimited usage. Refer to generator set manufacturers for further denitions on load management ratings, load factor or average power consumption, peak demand and how these ratings are typically applied. Even though there is some standardization of these ratings across the manufacturers, there also exists some uniqueness with regards to how each manufacturer applies their generator sets.

Electrical rating denitions for natural gas powered gensets are typically dened as standby or continuous with denitions similar to those mentioned above for diesels. Natural gas gensets recover more slowly than diesel gensets when subjected to block loads. Diesel engines have a much more direct path from the engine governor and fuel delivery system to the combustion chamber and this results in a very responsive engine-generator. A natural gas engine is challenged with air-fuel ow dynamics and a much more indirect path from the engine governor (throttle actuator) and fuel delivery system (natural gas pressure regulator, fuel valve and actuator, carburetor mixer, aftercooler, intake manifold) to the combustion chamber and this results in a less responsive engine-generator. Diesel gensets recover about twice as fast as natural gas gensets. For the actual calculations involved for sizing a genset, there are readily accessible computer software programs which are available on the genset manufacturer's Internet sites or from the manufacturer's dealers or distributors. These programs are used to quickly and accurately size generator sets for their application. The programs take into consideration the many different parameters discussed above including the size and type of the electrical loads (resistive, inductive, SCR etc.), reduced voltage soft starting devices (RVSS), motor types, voltage, fuel type, site conditions, ambient conditions and other variables. The software will optimize the starting sequences of the motors for the least amount of voltage dip and determine the starting kVA needed from the genset. It also provides transient response data including voltage dip magnitude and recovery duration. If the transient response is unacceptable, then design changes can be considered including oversizing the generator to handle the additional kvar load, adding RVSS devices to reduce the inrush current, improving system power factor and other methods. The computer software programs are quite exible in that they allow changes to the many different variables and parameters to achieve an optimum design. The software allows, for example, minimizing voltage dips or using paralleled gensets vs. a single genset.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0049

TOC

Index

Power Distribution Systems Generator System Design

1.2-9

Master TOC

Genset Sizing Guidelines

Some conservative rules of thumb for genset sizing include: 1. Oversize genset 20 25% for reserve capacity and for motor starting. 2. Oversize gensets for unbalanced loading or low power factor running loads. 3. Use 1/2 hp per kW for motor loads. 4. For variable frequency drives, oversize the genset by at least 40%. 5. For UPS systems, oversize the genset by 40% for 6 pulse and 15% for 6 pulse with input lters or 12 pulse. 6. Always start the largest motor rst when stepping loads. For basic sizing of a generator system, the following example could be used:

Generator Set Installation and Site Considerations

There are many different installation parameters and site conditions that must be considered to have a successful generator set installation. The following is a partial list of areas to consider when conducting this design. Some of these installation parameters include:
s

s s s s

s s s s s

Step 1: Calculate Running Amperes

Motor loads: u 200 hp motor . . . . . . . . . . . . 156 A u 100 hp motor . . . . . . . . . . . . . 78 A u 60 hp motor . . . . . . . . . . . . . . 48 A s Lighting Load . . . . . . . . . . . . . . 68 A s Miscellaneous Loads . . . . . . . . 95 A s Running Amperes . . . . . . . . . . 445 A
s

Foundation type (crushed rock, concrete, dirt, wood, separate concrete inertia pad etc.). Foundation to genset vibration dampening (spring type, cork and rubber etc.). Noise attenuation (radiator fan mechanical noise, exhaust noise, air intake noise). Combustion and cooling air requirements. Exhaust backpressure requirements. Emissions permitting. Delivery and rigging requirements. Genset derating due to high altitudes or excessive ambient temperatures.

s s

Hazardous waste considerations for fuel, antifreeze, engine oil. Meeting local building and electrical codes. Genset exposure (coastal conditions, dust, chemicals etc.). Properly sized starting systems (compressed air, batteries and charger). Allowing adequate space for installation of the genset and for maintenance (i.e., air lter removal, oil changing, general genset inspection etc). Flex connections on all systems that are attached to the genset and a rigid structure (fuel piping, foundation vibration isolators, exhaust, air intake, control wiring, power cables, radiator anges/duct work etc.). Diesel fuel day tank systems (pumps, return piping). Fuel storage tank (double walled, re codes) and other parameters.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

Please see the generator set manufacturers Application and Installation Guidelines for proper application and operation of their equipment.

Step 2: Calculating Starting Amperes Using 1.25 Multiplier

Motor loads: . . . . . . . . . . . . . . . . . . . . . . . 195 A u . . . . . . . . . . . . . . . . . . . . . . . . 98 A u . . . . . . . . . . . . . . . . . . . . . . . . 60 A s Lighting Load . . . . . . . . . . . . . . 68 A s Miscellaneous Loads . . . . . . . . 95 A s Starting Amperes . . . . . . . . . . 516 A
s u

Step 3: Selecting kVA of Generator

s

Running kVA = (445 A x 480 V x 1.732)/ 1000 = 370 kVA s Starting kVA = (516 A x 480 V x 1.732)/ 1000 = 428 kVA

Solution Generator must have a minimum starting capability of 428 kVA and minimum running capability of 370 kVA.
Also, please see Section Factors Governing Voltage Drop on Page 1.3-21 for further discussion on generator loading and reduced voltage starting techniques for motors.

Figure 1.2-9. Typical Genset Installation

Note: Courtesy of Caterpillar, Inc.

19 20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.2-10 Power Distribution Systems

TOC Index

June 2006
Sheet 0050

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

This page intentionally left blank.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0051

TOC

Index

Power Distribution Systems System Analysis

1.3-1

Master TOC

Systems Analysis
A major consideration in the design of a distribution system is to ensure that it provides the required quality of service to the various loads. This includes serving each load under normal conditions and, under abnormal conditions, providing the desired protection to service and system apparatus so that interruptions of service are minimized consistent with good economic and mechanical design. Under normal conditions, the important technical factors include voltage prole, losses, load ow, effects of motor starting, service continuity and reliability. The prime considerations under faulted conditions are apparatus protection, fault isolation and service continuity. During the system preliminary planning stage, before selection of the distribution apparatus, several distribution systems should be analyzed and evaluated including both economic and technical factors. During this stage if system size or complexity warrant, it may be appropriate to provide a thorough review of each system under both normal and abnormal conditions.

The principal types of computer programs utilized to provide system studies include:
s

Short circuit identify 3-phase and line-to-ground fault currents and system impedances. Arc ash calculates arc ash energy levels which lead to the selection of personal protective equipment (PPE). Circuit breaker duty identify asymmetrical fault current based on X/R ratio. Protective device coordination determine characteristics and settings of medium voltage protective relays and fuses, and entire low voltage circuit breaker and fuse coordination. Load ow simulate normal load conditions of system voltages, power factor, line and transformer loadings. Motor starting identify system voltages, motor terminal voltage, motor accelerating torque, and motor accelerating time when starting large motors.

Short circuit calculations dene momentary and steady-state fault currents for LV and MV breaker and fuse duty and bus bracings at any selected location in the system and also determine the effect on the system after removal of utility power due to breaker operation or scheduled power outages. Computer software programs can identify the fault current at any bus, in every line or source connected to the faulted bus, or to it and every adjacent bus, or to it and every bus which is one and two buses away, or currents in every line or source in the system. The results of these calculations permit optimizing service to the loads while properly applying distribution apparatus within their intended limits. The following additional studies should be considered depending upon the type and complexity of the distribution system, the type of facility and the type of loads to be connected to the system:
s s s s s

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Harmonic Analysis Transient Stability Insulation Coordination Grounding Study Switching Transient

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-2

Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0052

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Short Circuit Currents General

The amount of current available in a short circuit fault is determined by the capacity of the system voltage sources and the impedances of the system, including the fault. Voltage sources include the power supply (utility or on-site generation) plus all rotating machines connected to the system at the time of the fault. A fault may be either an arcing or bolted fault. In an arcing fault, part of the circuit voltage is consumed across the fault and the total fault current is somewhat smaller than for a bolted fault, so the latter is the worst condition, and therefore is the value sought in the fault calculations. Basically, the short circuit current is determined by applying Ohms Law to an equivalent circuit consisting of a constant voltage source and a time varying impedance. A time varying impedance is used in order to account for the changes in the effective voltages of the rotating machines during the fault. In an ac system, the resulting short circuit current starts out higher in magnitude than the nal steady state value and asymmetrical (due to the dc offset) about the X-axis. The current then decays toward a lower symmetrical steady-state value. The time varying characteristic of the impedance accounts for the symmetrical decay in current. The ratio of the reactive and resistive components (X/R ratio) accounts for the dc decay, see Figure 1.3-1. The fault current consists of an exponentially decreasing directcurrent component superimposed upon a decaying alternating-current. The rate of decay of both the dc and ac components depends upon the ratio of reactance to resistance (X/R) of the circuit. The greater this ratio, the longer the current remains higher than the steady-state value which it would eventually reach. The total fault current is not symmetrical with respect to the time-axis because of the direct-current component, hence it is called asymmetrical current. The dc component depends on the point on the voltage wave at which the fault is initiated. See Table 1.3-2 for multiplying factors that relate the rms asymmetrical value of Total Current to the rms symmetrical value, and the peak asymmetrical value of Total Current to the rms symmetrical value.

The ac component is not constant if rotating machines are connected to the system because the impedance of this apparatus is not constant. The rapid variation of motor and generator impedance is due to these factors: Subtransient Reactance (x d ), deter" mines fault current during the rst cycle, and after about 6 cycles this value increases to the transient reactance. It is used for the calculation of the momentary interrupting and/or momentary withstand duties of equipment and/or system. Transient Reactance (x d), which deter' mines fault current after about 6 cycles and this value in 1/2 to 2 seconds increases to the value of the synchronous reactance. It is used in the setting of the phase OC relays of generators and medium voltage circuit breakers. Synchronous Reactance (xd ), which determines fault current after steady state condition is reached. It has no effect as far as short circuit calculations are concerned but is useful in the determination of relay settings. Transformer Impedance, in percent, is dened as that percent of rated primary voltage that must be applied to the transformer to produce rated current owing in the secondary, with secondary shorted through zero resistance. Therefore, assuming the primary voltage can be sustained (generally referred to as an innite or unlimited supply), the maximum current a transformer can deliver to a fault condition is the quantity of (100 divided by percent impedance) times the transformer

rated secondary current. Limiting the power source fault capacity will thereby reduce the maximum fault current from the transformer. The electric network which determines the short circuit current consists of an ac driving voltage equal to the prefault system voltage and an impedance corresponding to that observed when looking back into the system from the fault location. In medium and high voltage work, it is generally satisfactory to regard reactance as the entire impedance; resistance may be neglected. However, this is normally permissible only if the X/R ratio of the medium voltage system is equal to or more than 25. In low voltage (1000 volts and below) calculations, it is usually worthwhile to attempt greater accuracy by including resistance with reactance in dealing with impedance. It is for this reason, plus ease of manipulating the various impedances of cables and buses and transformers of the low voltage circuits, that computer studies are recommended before nal selection of apparatus and system arrangements. When evaluating the adequacy of short circuit ratings of medium voltage circuit breakers and fuses, both the rms symmetrical value and asymmetrical value of the short circuit current should be determined. For low voltage circuit breakers and fuses, the rms symmetrical value should be determined along with either: the X/R ratio of the fault at the device or the asymmetrical short circuit current.

Total Current - A Wholly Offset Asymmetrical Alternating Wave 3.0 2.5 2.0 Scale of Curent Values 1.5 1.0 0.5 1 0 0.5 -1.0 -1.5 -2.0 Direct Component - The Axis Time in Cycles of of Symmetrical Wave a 60 Hz Wave 2 3 4 rms Value of Total Current Alternating Component Symmetrical Wave rms Value of Alternating Component

Figure 1.3-1. Structure of an Asymmetrical Current Wave

For more information visit: www.EatonElectrical.com CA08104001E

June 2006
Sheet 0053

TOC

Index

Power Distribution Systems System Analysis

1.3-3

Master TOC

Fault Current Waveform Relationships

The following Figure 1.3-2 describes the relationship between fault current peak values, rms symmetrical values and rms asymmetrical values depending on the calculated X/R ratio. The table is based on the following general formulas:
t ----------- 1 + e X R 2t -------------XR

i
2 60 --------------120 --------------- 1 + e X R = ---------

Based on a 60 Hz system and t = 1/2 cycle (ANSI/IEEEC37.13.1990/10.1.4) Ip ----- = 2 I 2 1 + e

XR

ii

Peak multiplication factor =

1
2 ----------XR

1.

Ip = I 2

rms multiplication factor = Example for X/R =15 Peak mf = 2 1 + e

------ 15

I rms asym ----------------------------- = 1 + 2e I

( 2 ) ( 2 60 ) -----------------------------120 -----------------------------XR

2 3 4

1 + 2e

2. I rms asym = I 1 + 2e Where:

2.5612

I = Symmetrical rms current Ip = Peak current e = 2.718 =2f f = Frequency in Hz t = Time in seconds rms mf = 1 + 2e
2 ---------15

5
1.5217

6 7 8 9

2.8 PEAK MAXIMUM ASYMMETRICAL 2.7 2.6 2.5 2.4 2.3 2.2 2.1 PEAK MULTIPLICATION FA L LT A AT FACTOR = 2.0 1.9 1.8 1.7 1.6 1.5
OR CT FA

Based Upon:

RMS SYMMETRICAL

RMS SYMMETRICAL

rms Asym = dc 2 + rms Sym2 with dc V e T Ta Taken at Current Peak

RMS MAXIMUM ASYMMETRICAL

10 11 12 13 14 15 16 17 18 19 20

CA TI O N

FA CT

O R

1.8 1.7 1.6 1.5 1.4

1.4 1.3 1.2 1.1

SM RM

L TIP UL

TI ICA

ON

1.5

2.5

8 9 10

15

20

25

30

40

50

60 70 80 90 100

CIRCUIT X/R RATIO (TAN PHASE) A AT T TA

Figure 1.3-2. Relation of X/R Ratio to Multiplication Factor

RMS MULTIPLICATION FACTOR = L LT A AT FA

PE A

U LT IP LI

21
CA08104001E For more information visit: www.EatonElectrical.com

1.3-4

Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0054

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Fault Current Calculations

The calculation of asymmetrical currents is a laborious procedure since the degree of asymmetry is not the same on all three phases. It is common practice for medium voltage systems, to calculate the rms symmetrical fault current, with the assumption being made that the dc component has decayed to zero, and then apply a multiplying factor to obtain the rst half-cycle rms asymmetrical current, which is called the momentary current. For medium voltage systems (dened by IEEE as greater than 1000 volts up to 69,000 volts) the multiplying factor is established by NEMA and ANSI standards depending upon the operating speed of the breaker. For low voltage systems, short circuit study software usually calculates the symmetrical fault current and the faulted system X/R ratio using ANSI guidelines. If the X/R ratio is within the standard, and the breaker interrupting current is under the symmetrical fault value, the breaker is properly rated. If the X/R ratio is higher than ANSI standards, the study applies a multiplying factor to the symmetrical calculated value (based on the X/R value of the system fault) and compares that value to the breaker symmetrical value to assess if it is properly rated. In the past, especially using manual calculations, a multiplying factor of 1.17 (based on the use of an X/R ratio of 6.6 representing a source short circuit power factor of 15%) was used to calculate the asymmetrical current. These values take into account that medium voltage breakers are rated on maximum asymmetry and low voltage breakers are rated average asymmetry. To determine the motor contribution during the rst half-cycle fault current, when individual motor horsepower load is known, the subtransient reactances found in the IEEE Red should be used in the calculations. When the system motor load is unknown, the following assumptions generally are made: Induction Motors Use 4.0 times motor full load current (impedance value of 25%).
Note: For motors fed through adjustable frequency drives or solid-state soft starters, there is no contribution to fault current, unless 1) they have an internal run contactor or 2) they have a bypass contactor.

Synchronous Motors Use 5.0 times motor full load current (impedance value of 20%). When the motor load is not known, the following assumptions generally are made:

Medium Voltage Motors

If known, use actual values otherwise use the values indicated for the same type of motor.

Calculation Methods
The following pages describe various methods of calculating short circuit currents for both medium and low voltage systems. A summary of the types of methods and types of calculations is as follows:
s s s

208Y/120 V Systems
s

Assume 50% lighting and 50% motor load. or

Assume motor feedback contribution of twice full load current of transformer. or

240/480/600 V 3-Phase, 3-Wire or 4-Wire Systems

s

Assume 100% motor load. or

s

Assume motors 25% synchronous and 75% induction.

s

or
s

Assume motor feedback contribution of four times full load current of transformer. Assume 50% induction motor load. or

s s s s

480Y/277 V Systems in Commercial Buildings

s

Assume motor feedback contribution of two times full load current of transformer or source.

Medium Voltage Switchgear exact method . . . . . . . . . Page 1.3-5 Medium Voltage Switchgear quick check table . . . . . . Page 1.3-7 Medium Voltage Switchgear Example 1 Verify ratings of breakers . . . . . . . . . . . . . Page 1.3-8 Medium Voltage Switchgear Example 2 Verify ratings of breakers with rotating loads . . . . . . . . . . . . . . . . Page 1.3-9 Medium Voltage Switchgear Example 3 Verify ratings of breakers with generators . . . . . . . . . . . Page 1.3-10 Medium Voltage Fuses exact method . . . . . . . . . Page 1.3-11 Power Breakers Asymmetry derating factors . . . . . . . Page 1.3-11 Molded Case Breakers asymmetry derating factors . . . . . . . Page 1.3-12 Short Circuit Calculations Short cut method for a system . . . . . . . . . . . . . Page 1.3-13 Short Circuit Calculations Short cut method for end of cable . . . . . . . . . . Page 1.3-15 Short Circuit Calculations Short cut method for end of cable chart method . . . . Page 1.3-16 Short Circuit Currents Chart of transformers 300 to 3750 kVA . . . . . . . . . . . . . Page 1.5-9

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0055

TOC

Index

Power Distribution Systems System Analysis

1.3-5

Master TOC

Fault Current Calculations for Specic Equipment Exact Method

The purpose of the fault current calculations is to determine the fault current at the location of a circuit breaker, fuse or other fault interrupting device in order to select a device adequate for the calculated fault current or to check the thermal and momentary ratings of noninterrupting devices. When the devices to be used are ANSI-rated devices, the fault current must be calculated and the device selected as per ANSI standards. The calculation of available fault current and system X/R rating is also utilized to verify adequate bus bar bracing and momentary withstand ratings of devices such as contactors.

a voltage = maximum rated voltage divided by K (for example, 4.76/1.24 = 3.85). If this breaker is applied in a system rated at 2.4 kV the calculated fault current must be less than 36 kA.

greater than the available system fault current of 20,000 amperes, the breaker is acceptable (assumes the breakers momentary and fault close rating is also acceptable).
Note: If the system available fault current were 22,000 amperes symmetrical, this breaker could not be utilized even though the Maximum Symmetrical Interrupting Capability is greater than 22,000 since Test 1 calculation is not satised.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

For example, consider the following case:

Assume a 12.47 kV system with 20,000 amperes symmetrical available. In order to determine if an Eatons Cutler-Hammer Type 150 VCP-W 500 vacuum breaker is suitable for this application, check the following: From Table 5.0-1 in Section 5 under column Rated Maximum Voltage V = 15 kV, under column Rated short circuit Current I = 18 kA, Rated Voltage Range Factor K = 1.3. Test 1 for V/Vo x I or 15 kV/12.47 kV x 18 kA = 21.65; also check K x I (which is shown in the column headed Maximum Symmetrical Interrupting Capability) or 1.3 x 18 kA = 23.4 kA. Since both of these numbers are Table 1.3-1. Reactance X
System Component

Medium Voltage VCP-W Metal-Clad Switchgear

The applicable ANSI Standards C37 is the latest applicable edition. The following is a review of the meaning of the ratings. (See Section 5.)

For approximate calculations, Table 1.3-1 provides typical values of % reactance (X) and X/R values for various rotating equipment and transformers. For simplication purposes, the transformer impedance (Z) has been assumed to be primarily reactance (X). In addition, the resistance (R) for these simplied calculations has been ignored. For detailed calculations, the values from the IEEE Red Book Standard 141, for rotating machines, and ANSI C57 and/or C37 for transformers should be utilized.

The Rated Maximum Voltage

This designates the upper limit of design and operation of a circuit breaker. For example, a circuit breaker with a 4.76 kV rated maximum voltage cannot be used in a 4.8 kV system.
2-Pole Turbo Generator 4-Pole Turbo Generator Hydro Generator with Damper Wedges and Synchronous Condensers Hydro Generator without Damper Windings All Synchronous Motors Ind. Motors Above 1000 hp, 1800 Rpm and Above 250 hp, 3600 Rpm Ind. Motors Below 50 hp and All Single-Phase Motors Distribution System from Remote Transformers Current Limiting Reactors

Reactance X Used for Typical Values and Range Short Circuit Close and Latch on Component Base Duty (Momentary) % Reactance X/R Ratio X X X .75X 1.5X 1.5X X X X .75X 1.0X 1.0X 1.2X Neglect X X 9 (7 14) 15 (12 17) 20 (13 32) 16 (16 50) 20 (13 35) 17 (15 25) 17 (15 25) 80 (40 120) 80 (40 120) 30 (10 60) 30 (10 60) 30 (10 60) 30 (15 40) 15 (2 40)

K-Rated Voltage Factor

The rated voltage divided by this factor determines the system kV a breaker can be applied up to the short circuit kVA rating calculated by the formula
3 Rated SC Current Rated Max. Voltage

All Other Induction Motors 50 hp and Above 3.0X Neglect X X

As Specied 15 (5 15) or Calculated As Specied 80 (40 120) or Calculated 8.0 18 (7 24)

Note: Interrupting capabilities of some of todays vacuum breakers may have K = 1, whereby the interrupting current is constant across its entire operating range.

Transformers
OA to 10 MVA, 69 kV OA to 10 MVA, above 69 kV FOA 12 to 30 MVA FOA 40 to 100 MVA X X X X X X X X 18 (7 24) 8.0 to 10.5 Depends on 20 (7 30) Primary Windings BIL 38 (32 44) Rating

Rated Short Circuit Current

This is the symmetrical rms value of current that the breaker can interrupt at rated maximum voltage. It should be noted that the product 3 x 4.76 x 29,000 = 239,092 kVA is less than the nominal 250,000 kVA listed. This rating (29,000 amperes) is also the base quantity that all the related capabilities are referred to.

Table 1.3-2. Typical System X/R Ratio Range (for Estimating Purposes)
Type of Circuit Remote generation through other types of circuits such as transformers rated 10 MVA or smaller for each 3-phase bank, transmission lines, distribution feeders, etc. Remote generation connected through transformer rated 10 MVA to 100 MVA for each 3-phase bank, where the transformers provide 90 percent or more of the total equivalent impedance to the fault point. Remote generation connected through transformers rated 100 MVA or larger for each 3-phase bank where the transformers provide 90 percent or more of the total equivalent impedance to the fault point. Synchronous machines connected through transformers rated 25 to 100 MVA for each 3-phase bank. Synchronous machines connected through transformers rated 100 MVA and larger. Synchronous machines connected directly to the bus or through reactors. X/R Range 15 or less 15 40

Maximum Symmetrical Interrupting Capability

This is expressed in rms symmetrical amperes or kiloamperes and is K x I rated; 29,000 x 1.24 = 35,960 rounded to 36 kA. This is the rms symmetrical current that the breaker can interrupt down to
CA08104001E

30 50

30 50 40 60 40 120

For more information visit: www.EatonElectrical.com

1.3-6

Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0056

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10

The Close and Latch Capability

This is also a related quantity expressed in rms asymmetrical amperes by 1.6 x maximum symmetrical interrupting capability. For example 1.6 x 36 = 57.6 or 58 kA, or 1.6 K x rated short circuit current. Another way of expressing the close and latch rating is in terms of the peak current, which is the instantaneous value of the current at the crest. ANSI Standard C37.09 indicates that the ratio of the peak to rms asymmetrical value for any asymmetry of 100% to 20% (percent asymmetry is dened as the ratio of dc component of the fault in per unit to 2 ) varies not more than 2% from a ratio of 1.69. Therefore the close and latch current expressed in terms of the peak amperes is = 1.6 x 1.69 x K x rated short circuit current. In the calculation of faults for the purposes of breaker selection, the rotating machine impedances specied in ANSI Standard C37.010 Article 5.4.1 should be used. The value of the impedances and their X/R ratios should be obtained from the equipment manufacturer. At initial short circuit studies, data from manufacturers is not available. Typical values of

impedances and their X/R ratios are given in Table 1.3-1. The ANSI Standard C37.010 allows the use of the X values only in determining the E/X value of a fault current. The R values are used to determine the X/R ratio, in order to apply the proper multiplying factor, to account for the total fault clearing time, asymmetry, and decrement of the fault current. The steps in the calculation of fault currents and breaker selection are described hereinafter: Step 1: Collect the X and R data of the circuit elements. Convert to a common kVA and voltage base. If the reactances and resistances are given either in ohms or per unit on a different voltage or kVA base, all should be changed to the same kVA and voltage base. This caution does not apply where the base voltages are the same as the transformation ratio. Step 2: Construct the sequence networks and connect properly for the type of fault under consideration. Use the X values required by ANSI Standard C37.010 for the interrupting duty value of the short circuit current.

Step 3: Reduce the reactance network to an equivalent reactance. Call this reactance XI. Step 4: Setup the same network for resistance values. Step 5: Reduce the resistance network to an equivalent resistance. Call this resistance RI. The above calculations of XI and RI may be calculated by several computer programs. Step 6: Calculate the E/XI value, where E is the prefault value of the voltage at the point of fault nominally assumed 1.0 pu. X Step 7: Determine X/R = ------I as RI previously calculated. Step 8: Go to the proper curve for the type of fault under consideration (3-phase, phase-to-phase, phase-toground), type of breaker at the location (2, 3, 5 or 8 cycles), and contact parting time to determine the multiplier to the calculated E/XI. See Figures 1.3-3, 1.3-4 and 1.3-5 for 5-cycle breaker multiplying factors. Use Figure 1.3-5 if the short circuit is fed predominantly from generators removed from the fault by two or more

130

130 120 8 7 110

5

130 120 5 110 4

11 12 13 14
Ratio X/R

120 110 100 90 80

12

10

90 80 Ratio X/R 70 60 50 40 30
5-CYCLE BREAKER

80 Ratio X/R 70 60 50 40 30 20 10 1.0 1.1 1.2 1.3 1.4

70 60 50 40

NT AC T P ART ING

17
30

CO

18 19 20 21

5-CYCLE BREAKER

20 10

20 10

5-CYCLE BREAKER

1.0 1.1 1.2 1.3 1.4 Multiplying Factors for E / X Amperes

1.0

1.1

CO

1.2

NT AC

16

PA RT IN
1.3 1.4

15

TIME

Multiplying Factors for E / X Amperes

Multiplying Factors for E / X Amperes

Figure 1.3-3. 3-phase Fault Multiplying Factors Which Include Effects of ac and dc Decrement

Figure 1.3-4. Line-to-Ground Fault Multiplying Factors Which Include Effects of ac and dc Decrement
For more information visit: www.EatonElectrical.com

Figure 1.3-5. 3-phase and Line-to-Ground Fault Multiplying Factors Which Include Effects of dc Decrement Only
CA08104001E

GT IME

90

100

8 6

100

June 2006
Sheet 0057

TOC

Index

Power Distribution Systems System Analysis

1.3-7

Master TOC

transformations or the per unit reactance external to the generation is 1.5 times or more than the subtransient reactance of the generation on a common base. Also use Figure 1.3-5 where the fault is supplied by a utility only. Step 9: Interrupting duty short circuit current = E/XI x MFx = E/X2. Step 10: Construct the sequence (positive, negative and zero) networks properly connected for the type of fault under consideration. Use the X values required by ANSI Standard C37.010 for the Close and Latch duty value of the short circuit current. Step 11: Reduce the network to an equivalent reactance. Call the reactance X. Calculate E/X x 1.6 if the breaker close and latch capability is given in rms amperes or E/X x 2.7 if the breaker close and latch capability is given in peak or crest amperes. Step 12: Select a breaker whose: a. Maximum voltage rating exceeds the operating voltage of the system: b.
V max E ------ I -------------- KI X2 Vo

Section 5 of ANSI C37 provides further guidance for medium voltage breaker application.

Application Above 3,300 Feet (1,000 m)

The rated one-minute power frequency withstand voltage, the impulse withstand voltage, the continuous current rating, and the maximum voltage rating must be multiplied by the appropriate correction factors below to obtain modied ratings which must equal or exceed the application requirements.
Note: Intermediate values may be obtained by interpolation.

i ii 1 2 3

Reclosing Duty
ANSI Standard C37.010 indicates the reduction factors to use when circuit breakers are used as reclosers. CutlerHammer VCP-W breakers are listed at 100% rating factor for reclosing.

Application Quick Check Table

For application of circuit breakers in a radial system supplied from a single source transformer. Short circuit duty was determined using E/X amperes and 1.0 multiplying factor for X/R ratio of 15 or less and 1.25 multiplying factor for X/R ratios in the range of 15 to 40. Table 1.3-4. Application Quick Check Table
Source Transformer MVA Rating Motor Load 100% 1 1.5 2 2.5 3 3.75 5 7.5 10 10 12 15 20 0% 1.5 2 2.5 3 3.75 5 7.5 10 10 12 15 20 20 25 30 50 Breaker Type and Symmetrical Interrupting Capacity at the Operating Voltage 50 VCP-W 350 46.9 kA 50 VCP-W 250 36 kA 50 VCP-W 350 49 kA 50 VCP-W 250 12 kA Operating Voltage kV 2.4 4.16 6.6

Table 1.3-3. Altitude Derating

Altitude in Feet (Meters) Correction Factor Current Voltage 1.00 0.95 0.80

3,300 (1,006) (and Below) 1.00 5,000 (1,524) 0.99 10,000 (3,048) 0.96

4 5 6 7

12

13.8

8
50 VCP-W 250 10.1 kA 150 VCP-W 500 23 kA 150 VCP-W 500 22.5 kA 150 VCP-W 500 19.6 kA

9 10 11

See Table 6.0-1, Section 6. Where: I = Rated short circuit current Vmax = Rated maximum voltage of the breaker VD KI = Actual system voltage = Maximum symmetrical interrupting capacity

50 VCP-W 250 33.2 kA

75 VCP-W 500 41.3 kA 150 VCP-W 750 35 kA 150 VCP-W 1000 46.3 kA 150 VCP-W 750 30.4 kA 150 VCP-W 1000 40.2 kA

12 13 14 15 16 17 18 19 20 21

c. E/X x 1.6 rms closing and latching capability of the breaker and/or E/X x 2.7 Crest closing and latching capability of the breaker. The ANSI standards do not require the inclusion of resistances in the calculation of the required interrupting and close and latch capabilities. Thus the calculated values are conservative. However, when the capabilities of existing switchgears are investigated, the resistances should be included. For single line-to-ground faults the symmetrical interrupting capability is 1.15 x the symmetrical interrupting capability at any operating voltage but not to exceed the maximum symmetrical capability of the breaker.

Transformer impedance 6.5% or more, all other transformer impedances are 5.5% or more.

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-8

Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0058

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Application on Symmetrical Current Rating Basis

Example 1 Fault Calculations
Given a circuit breaker interrupting and momentary rating in the table below, verify the adequacy of the ratings for a system without motor loads, as shown. Table 1.3-5. Short Circuit Duty
Type Breaker 50VCP W250 V Max. 3-Phase Symmetrical Interrupting Capability at V Max. 4.76 kV 29 kA Max. KI 36 kA at 4.16 kV Oper. Voltage Close and Latch or Momentary 58 kA I3

For 3-Phase Fault

E I 3-Phase = ---X where X is ohms per phase and E is the highest typical line-to-neutral operating voltage or IB I 3-Phase = ----X where X is per unit reactance IB is base current MVA Base current I B = 3.75 = .52 kA 3 ( 4.16 kV ) I1 .52 I 3-Phase = ---- = ----------------- = 8.6 kA Sym. .0604 X System X = 9 (is less than 15) R would use 1.0 multiplying factor for short circuit duty, therefore, short circuit duty is 8.6 kA sym. for 3-phase fault I1 and momentary duty is 8.6 x 1.6 = 13.7 kA I3.

4.76 ---------- (29) = 33.2 kA I1 4.16 LG Symmetrical Interrupting Capability 36 kA 1.15 (33.2) = 38.2 kA I2

Note: Interrupting capabilities I1 and I2 at operating voltage must not exceed maximum symmetrical interrupting capability Kl.

Check capabilities I1, I2 and I3 on the following utility system where there is no motor contribution to short circuit.
24,200 Watts Load Losses
13.8 kV X R 375 MVA Available

On 13.8 kV System, 3.75 MVA Base 3.75 MVA Z = -------------------------------- = .01 pu or 1% 375 MVA
2 2 2 2 2X Z = X + R = R ------- + 1 2 R

= 15

For Line-to-Ground Fault

3I B 3E I LG = -------------------------- = -------------------------2X 1 + X 0 2X 1 + X 0 For this system, X0 is the zero sequence reactance of the transformer which is equal to the transformer positive sequence reactance and X1 is the positive sequence reactance of the system. Therefore, 3(.52) I LG = = 9.1 kA Sym. 2(.0604) + .0505 Using 1.0 multiplying factor (see Table 1.3-6), short-circuit duty = 9.1 kA Sym. LG (I2)

13.8 kV 3750 kVA

Z 1 1 R = ---------------------- = --------------- = ----------------- = .066% 2 15.03 266 X- +1 ------R

2

X = X ( R ) = 15 (.066) = .99% ---R

4.16 kV

Transformer Standard 5.5% Impedance has a 7.5% Manufacturing Tolerance

50VPC-W250

5.50 Standard Impedance -.41 (-7.5% Tolerance) Transformer Z = 5.09%

Answer
Figure 1.3-6. Example 1 One-Line Diagram

From transformer losses per unit or percent R is calculated

31,000 Watts Full Load 6,800 Watts No Load Transformer X = Z R
2 2 2 2

The 50VCP-W250 breaker capabilities exceed the duty requirements and may be applied. 24.2 kW R = ------------------------------- = .0065 pu or .65% 3750 kVA With this application, short cuts could have been taken for a quicker check of the application. If we assume unlimited short circuit available at 13.8 kV and that Trans. Z = X I B .52 Then I 3-Phase = ----- = ------------- = 9.5 kA Sym. X .055 X/R ratio 15 or less multiplying factor is 1.0 for short circuit duty. The short circuit duty is then 9.5 kA Sym. (I1, I2) and momentary duty is 9.5 x 1.6 kA = 15.2 kA (I3).
For more information visit: www.EatonElectrical.com CA08104001E

(5.09) (.65) =

25.91 .42 =

25.48

X = 5.05% X .99% 5.05% 6.04% .0604 pu R X/R .066% 15 .65% 8 .716 % 9 .00716 pu

13.8 kV System Transformer System Total or

June 2006
Sheet 0059

TOC

Index

Power Distribution Systems System Analysis

1.3-9

Master TOC

Example 2 Fault Calculations

Given the system shown with motor loads, calculate the fault currents and determine proper circuit breaker selection. All calculations on per unit basis. 7.5 MVA Base 7.5 MVA Base Current I B = ------------------------------- = .628 kA 3 6.9 kV
X 13.8 kV System (6.9) X = .628 -------------- = .015 ---------21 (13.8) Transformer .015 .055 .001 .0055 15 10 2 X = 25 R 197A FL X'' = 20% d X = 35 R 173A FL X'' = 25% d R X/R 13.8 kV System 13.8 kV 7500 kVA 21 kA Sym. Available X = 5.5% R = 0.55% X = 15 R X = 10 R

i ii 1 2 3

Z = 5.53%

6.9 kV 1

4 5 6 7

Total Source Transformer .070 pu .0065 pu 11

3000 hp Synchronous Motor X = .20 (.628) = .638 pu at 7.5 MVA base -----------------.197 2500 hp Ind. Motor (.628) X = .25 ------------------ = .908 pu at 7.5 MVA base (.173) E IB I 3-Ph = ---- = ----- where X on per unit base X X Table 1.3-6. Multiplying Factor for E/X Amperes (ANSI C37.010, 1979, Figures 1.1-8, 1.1-9 and 1.1-10)
System X/R Type VCP-W Vacuum Circuit Breaker Rated Interrupting Time, 5 Cycle Type of Fault Ratio 3-Phase Local 1 15 20 25 30 36 40 45 50 55 60 65 70 75 80 85 90 95 100 100 120 130 1.00 1.00 1.00 1.00 1.04 1.06 1.08 1.12 1.13 1.14 1.16 1.17 1.19 1.20 1.21 1.22 1.23 1.24 1.24 1.24 1.00 1.00 1.02 1.06 1.10 1.14 1.16 1.19 1.22 1.25 1.26 1.28 1.29 1.30 1.31 1.32 1.33 1.34 1.35 1.35 LG 3-Phase & LG Remote 1.00 1.00 1.05 1.10 1.13 1.17 1.22 1.25 1.27 1.30 1.32 1.33 1.35 1.36 1.37 1.38 1.39 1.40 1.41 1.42 1.43 1.43 Source of Short Circuit 3000 hp 1.0 PF Syn. 2500 hp Ind.

Figure 1.3-7. Example 2 One-Line Diagram

Source of Short Circuit Current I3 Source Transformer I1 3000 hp Syn. Motor I1 2500 hp Syn. Motor Interrupting E/X Amperes .628 .070 .628 (1.5) .638 .628 (1.5) .908 I3F = or = 8.971 = .656 = .461 10.088 10.1 kA Momentary E/X Amperes .628 .070 .628 .638 .628 .908 = 8.971 = .984 = .691 X R 11 25 35 X (1) R (X) 11 .070 25 .638 35 .908 1 R = 157 = 39 = 39

8 9 10 11 12 13 14

10.647 Total 1/R = 235 x 1.6 17.0 kA Momentary Duty

IB Total X = ------- = .628 = .062 ------------10.1 I 3F

---System X = .062 (235) = 14.5 is a Multiplying Factor of 1.0 from Table 1.3-6 R

Table 1.3-7. Short Circuit Duty = 10.1 kA

Breaker Type 75VCP-W500 150VCP-W500 V Max. 3-Phase Symmetrical Interrupting Capability at V Max. Max. KI 41 kA 23 kA at 6.9 kV Oper. Voltage 8.25 6.9 (33) = 39.5 kA Close and Latch or Momentary 66 kA 37 kA

15 16 17 18 19 20 21

8.25 kV 33 kA 15 kV 18 kA

15 (18) (39.1) = 23 kA 6.9 (But not to exceed KI)

Answer
Either breaker could be properly applied, but price will make the type 150VCP-W500 the more economical selection.

Where system X/R ratio is 15 or less, the Multiplying Factor is 1.0.

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-10 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0060

Master TOC

i ii 1 2 3 4 5 6 7 8

Example 3 Fault Calculations

Check breaker application or generator bus for the system of generators shown. Each generator is 7.5 MVA, 4.16 kV 1040 amperes full load, I B = 1.04 kA Sub transient reactance Xd = 11% or, X = 0.11 pu X Gen ---- ratio is 30 R 1 1 1 1 1 3 1 1 1 3 = + + = and = + + = XS X X X X RS R R R R X ---or X S = X and R S = R Therefore, System X S = X = Gen ---- = 30 -------------R R 3 3 RS Since generator neutral grounding reactors are used to limit the I LG to I3-phase or below, we need only check the I3 short circuit duty. I B I B I B 31 B ---------------------I B Phase = ----- + ----- + ----- + ----------- = 3(1.04) = 28.4 kA Symmetrical E/X Amperes .11 X X X X
---System X of 30 is a Multiplying Factor of 1.04 from Table 1.3-6. R

Answer
The 50VCP-W250 breaker could be applied.

G1

G2

G3

4.16 kV

Short-circuit duty is 28.4 (1.04) = 29.5 kA Symmetrical

3-Phase Symmetrical Interrupting Capability Breaker Type V Max. 4.76 kV at V Max. 29 kA Max. KI 36 kA at 4.16 kV Oper. Voltage 4.76 (29) = 33.2 kA 4.16 50VCP-W250

Figure 1.3-8. Example 3 One-Line Diagram

9 10 11 12 13 14 15 16 17 18 19 20 21

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0061

TOC

Index

Power Distribution Systems System Analysis

1.3-11

Master TOC

Medium Voltage Fuses Fault Calculations

There are two basic types of medium voltage fuses. The following denitions are taken from ANSI Standard C37.40.

Step 4 Construct the sequence networks using resistances and connect properly for the type of fault under consideration and reduce to a single equivalent resistance. Step 5 Calculate the E/XI value, where E is the prefault value of the voltage at the point of fault normally assumed 1.0 in pu. For 3-phase faults E/XI is the fault current to be used in determining the required interrupting capability of the fuse.
Note: It is not necessary to calculate a single phase-to-phase fault current. This current is very nearly 3 /2 x 3-phase fault. The line-to-ground fault may exceed the 3-phase fault for fuses located in generating stations with solidly grounded neutral generators, or in delta-wye transformers with the wye solidly grounded, where the sum of the positive and negative sequence impedances on the high voltage side (delta) is smaller than the impedance of the transformer.

Expulsion Fuse (Unit)

A vented fuse (unit) in which the expulsion effect of the gases produced by internal arcing, either alone or aided by other mechanisms, results in current interruption.

Current-Limiting Fuse (Unit)

A fuse unit that, when its currentresponsive element is melted by a current within the fuses specied current- limiting range, abruptly introduces a high resistance to reduce current magnitude and duration, resulting in subsequent current interruption. There are two classes of fuses; power and distribution. They are distinguished from each other by the current ratings and minimum melting type characteristics. The current limiting ability of a current limiting fuse is specied by its threshold ratio, peak let-through current and I2t characteristics.

includes induction and synchronous motor loads. The assumption is made that in 208Y/120-volt systems the contribution from motors is 2 times the full load current of step-down transformer. This corresponds to an assumed 50% motor aggregate impedance on a kVA base equal to the transformer kVA rating or 50% motor load. For 480-, 480Y/277- and 600-volt systems the assumption is made that the contribution from the motors is four times the full load current of the step-down transformer which corresponds to an assumed 25% aggregate motor impedance on a kVA base equal to the transformer kVA rating or 100% motor load. In low voltage systems which contain generators the subtransient reactance should be used. If the X/R to the point of fault is greater than 6.6, a derating multiplying factor (MF) must be applied. The X/R ratio is calculated in the same manner as that for medium voltage circuit breakers. Calculated symmetrical amperes x MF breaker interrupting rating. The multiplying factor MF can be calculated by the formula: ( ) ( X/R ) 2 [ 1 + 2.718 ] MF = 2.29 If the X/R of system feeding the breaker is not known, use X/R = 15. For fused breakers by the formula: 1 + 2 ( 2.718 ) MF = 1.25
( 2 ) ( X/R )

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

For single line-to-ground fault; X I = X I (+) + X I () + X I (0) E I f = ------ 3 XI Step 6 Select a fuse whose published interrupting rating exceeds the calculated fault current. Figure 1.3-2 should be used where older fuses asymmetrically rated are involved. The voltage rating of power fuses used on 3-phase systems should equal or exceed the maximum line-to-line voltage rating of the system. Current limiting fuses for 3-phase systems should be so applied that the fuse voltage rating is equal to or less than 1.41 x nominal system voltage.

Interrupting Ratings of Fuses

Modern fuses are rated in amperes rms symmetrical. They also have a listed asymmetrical rms rating which is 1.6 x the symmetrical rating. Refer to ANSI/IEEE C37.48 for fuse interrupting duty guidelines.

Calculation of the Fuse Required Interrupting Rating:

Step 1 Convert the fault from the utility to percent or per unit on a convenient voltage and kVA base. Step 2 Collect the X and R data of all the other circuit elements and convert to a percent or per unit on a convenient kVA and voltage base same as that used in Step 1. Use the substransient X and R for all generators and motors. Step 3 Construct the sequence networks using reactances and connect properly for the type of fault under consideration and reduce to a single equivalent reactance.

If the X/R of the system feeding the breaker is not known, use X/R = 20. Refer to Table 1.3-8 for the standard ranges of X/R and Power Factors used in testing and rating low voltage breakers. Refer to Table 1.3-9 for the circuit breaker interrupting rating multiplying factors to be used when the calculated X/R ratio or power factor at the point the breaker is to be applied in the power distribution system falls outside of the Table 1.3-8 X/R or power factors used in testing and rating the circuit breakers. MF is always greater than 1.0.

Low Voltage Power Circuit Breakers Fault Calculations

The steps for calculating the fault current for the selection of a low voltage power circuit breaker are the same as those used for medium voltage circuit breakers except that where the connected loads to the low voltage bus

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-12 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0062

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Molded Case Breakers and Insulated Case Circuit Breakers Fault Calculations
The method of fault calculation is the same as that for low voltage power circuit breakers. Again the calculated fault current x MF breaker interrupting capacity. Because molded case breakers are tested at lower X/R ratios the MFs are different than those for low voltage power circuit breakers.
X 2 R 2 1 + 2.718

Low Voltage Circuit Breaker Interrupting Derating Factors

Refer to Table 1.3-8 for the standard ranges of X/R and power factors used in testing and rating low voltage breakers. Refer to Table 1.3-9 for the circuit breaker interrupting rating de-rating factors to be used when the calculated X/R ratio or power factor at the point the breaker is to be applied in the power distribution system falls outside of the Table 1.3-8 X/R or power factors used in testing and rating the circuit breakers. Normally the short circuit power factor or X/R ratio of a distribution system need not be considered in applying low voltage circuit breakers. This is because the ratings established in the applicable standard are based on power factor values which amply cover most applications. Established standard values include the following: Table 1.3-8. Standard Test Power Factors
Interrupting Rating in kA 10 or Less Over 10 to 20 Over 20 All Power Factor Test Range .45 .50 .25 .30 .15 .20 .15 Maximum X/R Test Range 1.98 1.73 3.87 3.18 6.6 4.9 6.6 Minimum

Molded Case Circuit Breaker

Low Voltage Power Circuit Breaker

MF = --------------------------------------------------X 1 R 1 1 + 2.718

X 1 R 1 = test X/R value. X 2 R 2 = X/R at point where breaker is applied.

For distribution systems where the calculated short circuit current X/R ratio differs from the standard values given in the above table, circuit breaker interrupting rating derating factors from Table 1.3-9 table should be applied.

Table 1.3-9. Circuit Breaker Interrupting Rating Derating Factors

% P.F. X/R Interrupting Rating Molded Case or Insulated Case < / = 10 kA 50 30 25 20 15 12 10 8.5 7 5 1.73 3.18 3.87 4.90 6.59 8.27 9.95 11.72 14.25 19.97 1.000 .847 .805 .762 .718 .691 .673 .659 .645 .627 >10 kA < / = 20 kA 1.000 1.000 .950 .899 .847 .815 .794 .778 .761 .740 >20 kA 1.000 1.000 1.000 1.000 .942 .907 .883 .865 .847 .823 Power Circuit Breaker Unfused 1.000 1.000 1.000 1.000 1.000 .962 .937 .918 .899 .874 Fused 1.000 1.000 1.000 1.000 .939 .898 .870 .849 .827 .797

Note: These are derating factors applied to the breaker and are the inverse of MF.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0063

TOC

Index

Power Distribution Systems System Analysis

1.3-13

Master TOC

Short Circuit Calculations Short Cut Method

Determination of Short Circuit Current
Note 1: Transformer impedance generally relates to self-ventilated rating (e.g., with OA/FA/FOA transformer use OA base). Note 2: kV refers to line-to-line voltage in kilovolts. Note 3: Z refers to line-to-neutral impedance of system to fault where R + jX = Z. Note 4: When totaling the components of system Z, arithmetic combining of impedances as ohms Z. per unit Z. etc., is considered a short cut or approximate method; proper combining of impedances (e.g., source, cables transformers, conductors, etc). should use individual R and X components. This Total Z = Total R + j Total X (See IEEE Red Book Standard No. 141).
1. 2. Select convenient kVA base for system to be studied. Change per unit, or percent, impedance from one kVA base to another: (a) Per unit = pu impedance kVA base 2 = (b) Percent = % impedance kVA base 2 = kVA base 2 kVA base 1 kVA base 1

i ii 1 2
(pu impedance on kVA base 1)

3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

kVA base 2 (% impedance on kVA base 1)

3.

Change ohms, or percent or per-unit, etc.:

(ohms impedance) (kVA base) (a) Per unit impedance = pu Z = percent = 2 impedance ( kV ) ( 1000 ) 100 (b) % impedance = % Z = (c) Ohms impedance = (ohms impedance) (kVA base) 2 ( kV ) ( 10 ) ( kV )2

(% impedance) (10) kVA base

4.

Change power-source impedance to per-unit or percent impedance on kVA base as selected for this study:

(a) if utility fault capacity given in kVA kVA base in study Per-unit impedance = pu Z = -----------------------------------------------------------------------------------------power-source kVA fault capacity (b) if utility fault capacity given in rms symmetrical short circuit amperes kVA base in study Per-unit impedance = pu Z = --------------------------------------------------------------------------------------------------------------(short-circuit current) ( 3 )(kV of source)

5.

Change motor rating to kVA:

(a) (b) (c) (d)

motor kVA ( 3 ) (kV) (I) where I = motor nameplate full-load amperes if 1.0 power factor synchronous motor kVA = (0.8) (hp) if 0.8 power factor synchronous motor kVA = (1.0) (hp) if induction motor kVA = (1.0) (hp) 3-phase kVA or 1-phasekVA ( 3 ) ( kV )

6.

Determine symmetrical short circuit current:

(a) Base current = I Base = (b) Per unit I SC 1.0 = puZ

kV line-to-neutral

(c) rms Symmetrical current = ISC = (pu ISC) (IBase Amperes) 3-phase kVA base 1-phase kVA base (d) rms Symmetrical current = Amperes = ------------------------------------------------- or ------------------------------------------------( puZ ) ( kV ) ( puZ ) ( 3 ) ( kV ) (e) (g) (3-phase kVA base) (100) 1-phase kVA base (100) = --------------------------------------------------------------------- or ----------------------------------------------------------------(%Z) ( kV ) (%Z) ( 3 ) ( kV ) (kV) (1000) = ---------------------------------3 (ohms Z)

7.

Determine symmetrical short circuit kVA:

( kV )2 ( 1000 ) (a) Symmetrical short circuit kVA = kVA base = (kVA base) (100) = ----------------------------------------------------------------------------------------------------( puZ ) %Z ohms Z (b) 3(line-to-neutral kV)2 ( 1000 ) = ---------------------------------------------------------------------------(ohms Z)

8.

Determine line-to-line short circuit current:

(a) from 3-phase transformer approx. 86% of 3-phase current (b) three single-phase transformers (e.g., 75 kVA, Z = 2%) calculate same as one 3-phase unit (i.e., 3 x 75 kVA = 225 kVA, Z = 2%). (c) from single-phase transformer see Page 1.3-15. (a) synchronous motor 5 times motor full load current (impedance 20%) See IEEE Standard No. 141 (b) induction motor 4 times motor full-load current (impedance 25%) (c) motor loads not individually identied, use contribution from group of motors as follows: on 208Y/120 volt systems 2.0 times transformer full-load current on 240-480-600 volt 3-phase, 3-wire systems 4.0 times transformer full-load current on 480Y/277 volt 3-phase, 4-wire systems In commercial buildings, 2.0 times transformers full-load current (50% motor load) In industrial plants, 4.0 times transformer full-load current (100% motor load)

9.

Determine motor contribution (or feedback) as source of fault current:

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-14 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0064

Master TOC

i ii 1

Example Number 1
How to Calculate Short Circuit Currents at Ends of Conductors
A. System Diagram B. Impedance Diagram (Using Short Cut Method for Combining Impedances and Sources).
A Utility Source 500 MVA V VA Utility Major Contribution B C

2
Transformer Cables Switchboard Fault 1,000 kVA V VA 5.75% 480 Volts Cable

3 4

Cables Fault

Switchboard Fault

5 6 7 8 9 10 11 12 13 14
2 4(a)
A B C 100 Feet (30 m) 3 350 kcmil Cable in Steel Conduit

.002 pu

1.00 pu

1.00 pu

1.00 pu

.0575 pu

.027 pu Switchboard Fault

.027 pu

.027 pu

Mixed Load Motors and Lighting Each Feeder 100 Feet (30 m) of 3 350 kcmil Cable in Steel Conduit Feeding Lighting and 250 kVA of Motors Cable Fault Combining Series Impedances: ZTO
L

.027 pu Cable Fault = = + Z2 + ... +Zn

C. Conductor impedance from Table 1.5-20, Page 1.5-14. Conductors: 3 350 kcmil copper, single conductors Circuit length: 100 feet (30 m), in steel (magnetic) conduit Impedance Z = 0.00619 ohms/100 feet (30 m). ZTOT = 0.00619 ohms (100 circuit feet) D. Fault current calculations (combining impedances arithmetically, using approximate Short Cut method see Note 4, Page 1.3-13)
Step 1 Equation (See)

Combining Parallel Impedances:

1 ZTOTAL

1 + 1 + ... 1 Z1 Z2 Zn

.0595 pu

.342 pu

.0507 pu E .0777 pu

.027 pu

.027 pu

Calculation Select 1000 kVA as most convenient base, since all data except utility source is on secondary of 1000 kVA transformer. kVA base 1000 Utility per unit impedance = Z pu = ------------------------------------------ = -------------------- = 0.002 pu utility fault kVA 500.000 %Z Transformer per unit impedance = Z pu = --------- = 5.75 = 0.0575 pu ---------100 100 kVA base 1000 Motor contribution per unit impedance = Z pu = --------------------------------------- = ------------------- = 1.00 pu 4 x motor kVA 4 x 250 Cable impedance in ohms (see above) = 0.00619 ohms (ohms)(kVA base) Cable impedance per unit = Z pu = ------------------------------------------------- = (0.00619)(1000) = 0.027pu -----------------------------------------2 2 (0.480) (1000) (kV) (1000)

15 16 17 18

3(a)

4(a) and 9(c) 3(a)

6(d)

Total impedance to switchboard fault = 0.0507 pu (see diagram above) 3-phase kVA base Symmetrical short circuit current at switchboard fault = = = 23,720 amperes rms 1000 ( Z pu ) ( 3 ) ( kV ) ( 0.0507 ) ( 3 ) ( 0.480 )

19 20 21
7 6(d)

Total impedance to cable fault = 0.0777 pu (see diagram above) Symmetrical short circuit current at cable fault = 3-phasebase = = 15, 480 amperes rms kVA 1000 ( Z pu ) ( 3 ) ( kV ) ( 0.0777 ) ( 3 ) ( 0.480 )

Figure 1.3-9. Example Number 1

For more information visit: www.EatonElectrical.com CA08104001E

June 2006
Sheet 0065

TOC

Index

Power Distribution Systems System Analysis

1.3-15

Master TOC

Example Number 2
Fault Calculation Secondary Side of Single-Phase Transformer
A. System Diagram
R = 0.1498 Z 480-Volt 3-Phase Switchboard Bus at 50,000 Amp Symmetrical, X/R = 6.6 X = 0.9887 Z

i
Deriving Transformer R and X:

ii 1

X = 6.6 R Z=
2

X = 6.6 R
2

X +R =

( 6.6R ) + R = 43.56R + R = R = 0.1498Z X = 0.9887Z

44.56R = 6.6753R

100 Ft. Two #2/0 Copper Conductors, Magnetic Conduit R = 0.0104 Ohms X = 0.0051 Ohms

R=
75 kVA Single-Phase 480-120/240 Volts; Z = 2.8%, R = 1.64%, X = 2.27% V VA

2 3 4 5 6 7 8 9
= 0.00054 pu = 0.00356 pu = 0.00677 pu

6.6753

X = 6.6R
120 Volts F2 240 V F1

Half-winding of Transformer Full-winding of Transformer

{ Multiply % R by 1.5 } Reference: IEEE Standard No. 141 Multiply % X by 1.2

B. Impedance Diagram Fault F1

RSyst = 0.00054 RCond = 0.00677 RTfmr = 0.0164 RTotal = 0.02371 T To F1 F1 RSyst = 0.00356 RCond = 0.00332 RTfmr = 0.0227 RTotal = 0.02958 T To

C. Impedance Diagram Fault F2

RSyst = 0.00054 RCond = 0.00677 RTfmr = 0.0246 RTotal = 0.03191 T To F2 F2 XSyst = 0.00356 XCond = 0.00332 XTfmr = 0.0272 XTotal = 0.03408 T To

D. Impedance and Fault Current Calculations 75 kVA Base

Note: To account for the outgoing and return paths of single-phase circuits (conductors, systems, etc.) use twice the 3-phase values of R and X.
ZSyst =

= 0.0018pu 3 0.480 50,000

ohms kVA Base

75

(From Page 1.3-13 Formula 4(b) )

RSyst = 2 (0.1498 x Z) XSyst = 2 (0.9887 x Z) 0.0104 75 RCond = 2 2 0.48 1000 0.0051 75 XCond = 2 ( 0.48 ) 2 1000 1.64 RTfmr = 100 2.27 XTfmr = 100

10 11

ZCond =

2 ( kV ) 1000

(From Page 1.3-13 Formula 3(a) )

= 0.00332 pu = 0.0164 pu = 0.0277 pu = 0.0246 pu

Full-winding of Transformer (75 kVA Base)

12 13 14

Half-winding of Transformer (75 kVA Base)

1.64 RTfmr = 1.5 ( ) 100 XTfmr = 1.2

( 2.27 )
100
2 2

= 0.0272 pu
2 2

Impedance to Fault F1 Full Winding Impedance to Fault F2 Half Winding Short circuit current F1 = 75 (0.03791 x 0.240 kV) = 8,243 Ampere Symmetrical Short circuit current F2 = 75 (0.04669 x 0.120 kV) = 13,386 Ampere Symmetrical

Z= Z=

( 0.02371 ) + ( 0.02958 ) ( 0.03191 ) + ( 0.03408 )

= 0.03791 pu = 0.04669 pu

15 16 17 18 19 20 21

Figure 1.3-10. Example Number 2

Method 1: Short Cut Methods End of Cable

This method uses the approximation of adding Zs instead of the accurate method of Rs and Xs. For Example: For a 480/277-volt system with 30,000 amperes symmetrical available at the line side of a conductor run of 100 feet (30 m) of 2 500 kcmil per phase and neutral, the approximate fault current at the load side end
CA08104001E

of the conductors can be calculated as follows. 277 volts/30,000 amperes = 0.00923 ohms (source impedance) Conductor ohms for 500 kcmil conductor from reference data in this section in magnetic conduit is 0.00551 ohms per 100 feet (30 m). For 100 feet (30 m) and 2 conductors per phase we have: 0.00551/2 = 0.00273 ohms (conductor impedance)
For more information visit: www.EatonElectrical.com

Add source and conductor impedance or 0.00923 + 0.00273 = 0.01196 total ohms
Next, 277 volts/0.01196 ohms = 23,160 amperes rms at load side of conductors X 30,000 amperes available 100 feet (30 m) 2 500 kcmil per phase X If = 23,160 amperes

Figure 1.3-11. Short Circuit Diagram

1.3-16 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0066

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Method 2: Chart Approximate Method

The chart method is based on the following:

Step Five
Enter the chart along the bottom horizontal scale with the distance (in feet) from the transformer to the fault point. Draw a vertical line up the chart to the point where it intersects the selected curve. Then draw a horizontal line to the left from this point to the scale along the left side of the chart.

Motor Contribution
For system voltages of 120/208 volts, it is reasonable to assume that the connected load consists of 50% motor load, and that the motors will contribute four times their full load current into a fault. For system voltages of 240 and 480 volts, it is reasonable to assume that the connected load consists of 100% motor load, and that the motors will contribute four times their full load current into a fault. These motor contributions have been factored into each curve as if all motors were connected to the transformer terminals.

Step Six
The value obtained from the left-hand vertical scale is the fault current (in thousands of amperes) available at the fault point. For a more exact determination, see the formula method. It should be noted that even the most exact methods for calculating fault energy use some approximations and some assumptions. Therefore, it is appropriate to select a method which is sufciently accurate for the purpose, but not more burdensome than is justied. The charts which follow make use of simplications which are reasonable under most circumstances and will almost certainly yield answers which are on the safe side. This may, in some cases, lead to application of circuit breakers having interrupting ratings higher than necessary, but should eliminate the possibility of applying units which will not be safe for the possible fault duty.

Feeder Conductors
The conductor sizes most commonly used for feeders from molded case circuit breakers are shown. For conductor sizes not shown, the following table has been included for conversion to equivalent arrangements. In some cases it may be necessary to interpolate for unusual feeder ratings. Table 1.3-10 is based on using copper conductor. Table 1.3-10. Conductor Conversion (Based on Using Copper Conductor)
If Your Conductor is: 3 No. 4/0 Cables 4 No. 2/0 Cables 3 2000 kcmil Cables 5 400 kcmil Cables 6 300 kcmil Cables 800 Ampere Busway 1000 Ampere Busway 1600 Ampere Busway Use Equivalent Arrangement 2 500 kcmil 2 500 kcmil 4 750 kcmil 4 750 kcmil 4 750 kcmil 2 500 kcmil 2 500 kcmil 4 750 kcmil

UTILITY KVA V VA

12.5

10.0 250 kcmil W WG W WG

Short Circuit Current Readout

The readout obtained from the charts is the rms symmetrical amperes available at the given distance from the transformer. The circuit breaker should have an interrupting capacity at least as large as this value.

7.5

5.0

How to Use the Short Circuit Charts

Step One
Obtain the following data: 1. 2. 3. 4. System voltage Transformer kVA rating (from transformer nameplate) Transformer impedance (from transformer nameplate) Primary source fault energy available in kVA (from electric utility or distribution system engineers)

2.5

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

Figure 1.3-12. 225 kVA Transformer/4.5% Impedance/208 Volts

KV Fault Current in Thousands of Amperes (Sym.) 30 kcmil 25 #4 A 20 B F 15 F 50,000

Step Two
Select the applicable chart from the following pages. The charts are grouped by secondary system voltage which is listed with each transformer. Within each group, the chart for the lowest kVA transformer is shown rst, followed in ascending order to the highest rated transformer.

Step Three
Select the family of curves that is closest to the available source kVA. The black line family of curves is for a source of 500,000 kVA. The lower value line (in red) family of curves is for a source of 50,000 kVA. You may interpolate between curves if necessary, but for values above 100,000 kVA it is appropriate to use the 500,000 kVA curves.

10

Step Four
Select the specic curve for the conductor size being used. If your conductor size is something other than the sizes shown on the chart, refer to the conductor conversion Table 1.3-10.

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

Figure 1.3-13. 300 kVA Transformer/4.5% Impedance/208 Volts

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0067

TOC

Index

Power Distribution Systems System Analysis

1.3-17

Master TOC

B KV Fault Current in Thousands of Amperes (Sym.) 30 F 25 100 W WG 20 80 B F 50,000 120 A

i ii 1 2 3
#4 AWG A AW

15 4 2 10

60

40

20

4
0 0 2 5 10 20 50 Distance in Feet from T 100 200 500 1000 2000 5000 0 0 2 5 10 20 50 Distance in Feet from T 100 200 500 1000 2000 5000

5 6

Figure 1.3-14. 500 kVA Transformer/4.5% Impedance/208 Volts

Figure 1.3-17. 1500 kVA Transformer/5.5% Impedance/208 Volts

A Fault Current in Thousands of Amperes (Sym.) 60 50 W WG 40 B F 30 60 F 50,000 80 F 100 120 B W WG F

7 8 9 10 11

50,000

20 4 10 kcmil

40

20

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

12 13

Figure 1.3-15. 750 kVA Transformer/5.5% Impedance/208 Volts

Figure 1.3-18. 2000 kVA Transformer/5.5% Impedance/208 Volts

Fault Current in Thousands of Amperes (Sym.)

Fault Current in Thousands of Amperes (Sym.)

60 B 50

kcmil kcmil

A 12

14 15

10 B 8 F 50,000

F 40 F

50,000

16
4 2

30

17 18

20

W WG

10

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

19
0 2 5 10 20 50 Distance in Feet from T 100 200 500 1000 2000 5000

Figure 1.3-16. 1000 kVA Transformer/5.5% Impedance/208 Volts

Figure 1.3-19. 300 kVA Transformer/4.5% Impedance/480 Volts

20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-18 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0068

Master TOC

i
A Fault Current in Thousands of Amperes (Sym.) A Fault Current in Thousands of Amperes (Sym.) 60

ii 1 2 3 4

30

25 F 20 15 B #1/0 AW A AWG #4 AWG A AW 50,000

50

kcmil F 50,000

40

#4 AW A AWG B

30

10

20

750 kcmil

10

5 6
Fault Current in Thousands of Amperes (Sym.) 30

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

Figure 1.3-20. 500 kVA Transformer/4.5% Impedance/480 Volts

Figure 1.3-23. 1500 kVA Transformer/5.5% Impedance/480 Volts

Fault Current in Thousands of Amperes (Sym.)

7 8 9 10 11 12 13 14

A 60 4 kcmil

25

750 500 F 50,000

50

W WG F 50,000

20

B F

40 F 30

15

10

kcmil

20

#4 A 5

10

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

Figure 1.3-21. 750 kVA Transformer/5.5% Impedance/480 Volts

Figure 1.3-24. 2000 kVA Transformer/5.5% Impedance/480 Volts

A Fault Current in Thousands of Amperes (Sym.) 30 W WG B 25 F 20 F 50,000

15 16 17 18 19 20 21

15 4 750 kcmil 2 10

5 10 20 50 Distance in Feet from T

100

200

500

1000 2000

5000

Figure 1.3-22. 1000 kVA Transformer/5.5% Impedance/480 Volts

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0069

TOC

Index

Power Distribution Systems System Analysis

1.3-19

Master TOC

Determining X and R Values from Transformer Loss Data

Method 1:
Given a 500 kVA, 5.5% Z transformer with 9000 W total loss; 1700 W no-load loss; 7300 W load loss and primary voltage of 480 V. 3 500 R = 7300 Watts 3 0.480 %R = .0067 ohms 0.0067 500 %R = 2 = 1.46% 10 0.48 %X = 5.5 1.46 = 5.30%
2 2 2

How to Estimate Short Circuit Currents at Transformer Secondaries:

Method 1:
To obtain 3-phase rms symmetrical short circuit current available at transformer secondary terminals, use the formula: I SC 100 = I FLC ----------%Z

Method 2:
Refer to Page 1.5-9 in the Reference section, and use appropriate row of data based on transformer kVA and primary short circuit current available. This will yield more accurate results and allow for including motor short circuit contribution.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

where %Z is the transformer impedance in percent, from Tables 1.5-6 through 1.5-11, Page 1.5-11. This is the maximum 3-phase symmetrical bolted-fault current, assuming sustained primary voltage during fault, i.e., an innite or unlimited primary power source (zero source impedance). Since the power source must always have some impedance this a conservative value; actual fault current will be somewhat less.
Note: This will not include motor short circuit contribution.

Method 2:
Using same values above. I R Losses %R = 10 kVA 7300 = 1.46 10 500 %X = 5.5 1.46 = 5.30%
2 2 2

See Tables 1.5-12 through 1.5-15 on Page 1.5-12 for loss data on transformers.

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-20 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0070

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Voltage Drop Considerations

The rst consideration for voltage drop is that under the steady-state conditions of normal load, the voltage at the utilization equipment must be adequate. Fine-print notes in the NEC recommend sizing feeders and branch circuits so that the maximum voltage drop-in either does not exceed 3%, with the total voltage drop for feeders and branch circuits not to exceed 5%, for efciency of operation. (Fine print notes in the NEC are not mandatory.) In addition to steady-state conditions, voltage drop under transient conditions, with sudden high-current, shorttime loads, must be considered. The most common loads of this type are motor inrush currents during starting. These loads cause a voltage dip on the system as a result of the voltage drop in conductors, transformers and generators under the high current. This voltage dip can have numerous adverse effects on equipment in the system, and equipment and conductors must be designed and sized to minimize these problems. In many cases, reduced-voltage starting of motors to reduce inrush current will be necessary.

Computer Equipment: With the proliferation of data-processing and computer- or microprocessor-controlled manufacturing, the sensitivity of computers to voltage has become an important consideration. Severe dips of short duration can cause a computer to crash shut down completely, and other voltage transients caused by starting and stopping motors can cause data-processing errors. While voltage drops must be held to a minimum, in many cases computers will require special power-conditioning equipment to operate properly. Industrial Plants: Where large motors exist, and unit substation transformers are relatively limited in size, voltage dips of as much as 20% may be permissible in some cases, if they do not occur too frequently. Lighting is often supplied from separate transformers, and is minimally affected by voltage dips in the power systems. However, it is usually best to limit dips to between 5 and 10% at most. One critical consideration is that a large voltage dip can cause a dropout (opening) of magnetic motor contactors and control relays. The actual dropout voltage varies considerably among starters of different manufacturers. The only standard that exists is that of NEMA, which states that a starter must not drop out at 85% of its nominal coil voltage, allowing only a 15% dip. While most starters will tolerate considerably more voltage dip before dropping out, limiting dip to 15% is the only way to ensure continuity of operation in all cases. X-Ray Equipment: Medical x-ray and similar diagnostic equipment, such as CAT-scanners, are extremely sensitive to low voltage. They present a small, steady load to the system until the instant the x-ray tube is red. This presents a brief but extremely high instantaneous momentary load. In some modern x-ray equipment, the ring is repeated rapidly to create multiple images. The voltage regulation must be maintained within the manufacturers limits, usually 2 to 3%, under these momentary loads, to ensure proper x-ray exposure.

Motor Starting
Motor inrush on starting must be limited to minimize voltage dips. Table 1.3-11 on the next page will help select the proper type of motor starter for various motors, and to select generators of adequate size to limit voltage dip. See Section 30 for additional data on reduced voltage motor starting.

Utility Systems
Where the power is supplied by a utility network, the motor inrush can be assumed to be small compared to the system capacity, and voltage at the source can be assumed to be constant during motor starting. Voltage dip resulting from motor starting can be calculated on the basis of the voltage drop in the conductors between the power source and the motor resulting from the inrush current. Where the utility system is limited, the utility will often specify the maximum permissible inrush current or the maximum hp motor they will permit to be started across-the-line.

Transformer Considerations
If the power source is a transformer, and the inrush kVA or current of the motor being started is small compared to the full-rated kVA or current of the transformer, the transformer voltage dip will be small and may be ignored. As the motor inrush becomes a signicant percentage of the transformer full-load rating, an estimate of the transformer voltage drop must be added to the conductor voltage drop to obtain the total voltage drop to the motor. Accurate voltage drop calculation would be complex and depend upon transformer and conductor resistance, reactance, and impedance, as well as motor inrush current and power factor. However, an approximation can be made on the basis of the low power-factor motor inrush current (30 40%) and impedance of the transformer. For example, if a 480 V transformer has an impedance of 5%, and the motor inrush current is 25% of the transformer full-load current (FLC), then the worst case voltage drop will be 0.25 x 5%, or 1.25%. The allowable motor inrush current is determined by the total permissible voltage drop in transformer and conductors.

Recommended Limits of Voltage Variation

General Illumination: Flicker in incandescent lighting from voltage dip can be severe; lumen output drops about three times as much as the voltage dips. That is, a 10% drop in voltage will result in a 30% drop in light output. While the lumen output drop in uorescent lamps is roughly proportional to voltage drop, if the voltage dips about 25%, the lamp will go out momentarily and then restrike. For high-intensity discharge (HID) lamps such as mercury vapor, highpressure sodium or metal halide, if the lamp goes out because of an excessive voltage dip, it will not restrike until it has cooled. This will require several minutes. These lighting icker effects can be annoying, and in the case of HID lamps, sometimes serious. In areas where close work is being done, such as drafting rooms, precision assembly plants, and the like, even a slight variation, if repeated, can be very annoying, and reduce efciency. Voltage variation in such areas should be held to 2 or 3% under motor-starting or other transient conditions.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0071

TOC

Index

Power Distribution Systems System Analysis

1.3-21

Master TOC

Table 1.3-11. Factors Governing Voltage Drop

Type of Motor Starting Starting Torque Current How Started Starting Current % Full-Load Starting Torque per Unit of Full Load Torque Motor Rpm 1750 Design A Normal Normal Across-the-Line Resistance Autotransformer Across-the-Line Resistance Autotransformer Across-the-Line Resistance Autotransformer 600 700 480 560 375 450 500 600 400 480 320 400 500 600 400 480 320 400 1.5 .96 .96 1.5 .96 .96 1150 1.35 .87 .87 1.35 .87 .87 .2 to 2.5 1.28 to 1.6 1.28 to 1.6 850 1.25 .80 .80 1.25 .80 .80 Full-Load Amperes per kVA Generator Capacity for Each 1% Voltage Drop .0109 .00936 .0136 .0117 .0170 .0146 .0131 .0109 .0164 .01365 .0205 .0170 .0131 .0109 .0164 .01365 .0205 .0170 .0655 .0218 .0145 .0118 .0228 .0197

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Design B

Normal

Low

Design C

High

Low

Wound Rotor

High

Low

Secondary Controller 100% current for 100% Torque Across-the-Line Across-the-Line Autotransformer 300 450 550 288 350

Synchronous (for compressors) Low Synchronous (for centrifugal pumps) Low

40% Starting, 40% Pull-In 60% Starting, 110% Pull-In 38% Starting, 110% Pull-In

Consult NEMA MG-1 sections 1 and 12 for the exact denition of the design letter. In each case, a solid-state reduced voltage starter can be adjusted and controlled to provide the required inrush current and torque characteristics. Where accuracy is important, request the code letter of the the motor and starting and breakdown torques from the motor vendor. Using 80% taps.

Engine Generator Systems

With an engine generator as the source of power, the type of starter that will limit the inrush depends on the characteristics of the generator. Although automatic voltage regulators are usually used with all ac enginegenerators, the initial dip in voltage is caused by the inherent regulation of the generator and occurs too rapidly for the voltage regulator to respond. It will occur whether or not a regulator is installed. Consequently, the percent of initial voltage drop depends on the ratio of the starting kVA taken by the motor to the generator capacity, the inherent regulation of the generator, the power-factor of the load thrown on the generator, and the percentage load carried by the generator. A standard 80% power-factor enginetype generator (which would be used where power is to be supplied to motor loads) has an inherent regulation of approximately 40% from no-load to full-load. This means that a 50% variation in load would cause approximately 20% variation in voltage (50% x 40% = 20%). Assume that a 100 kVA, 80% PF engine-type generator is supplying the power and that the voltage drop should not exceed 10%. Can a 7-1/2 hp, 220-volt, 1750 rpm, 3-phase, squirrelcage motor be started without exceeding this voltage drop? Starting ratio = Percent voltage drop gen. kVA 1000 F.L. amperes volts 3 reg. of gen.

From the nameplate data on the motor the full-load amperes of a 7-1/2 hp. 220-volt, 1750 rpm, 3-phase, squirrelcage motor is 19.0 amperes. Therefore: Starting current (%F.L.) = 10 100 1000 = 3.45 or 345%. 19.0 220 3 0.40 From Table 1.3-11, a NEMA design C or NEMA design D motor with an autotransformer starter gives approximately this starting ratio. It could also be obtained from a properly set solid-state adjustable reduced voltage starter. The choice will depend upon the torque requirements of the load since the use of an autotransformer starter reduces the starting torque in direct proportion to the reduction in starting current. In other words, a NEMA design C motor with an autotransformer would have a starting torque of approximately full-load (see Table 1.3-11) whereas the NEMA design D motor under the same conditions would have a starting torque of approximately 1-1/2 times full-load.
Note: If a resistance starter were used for the same motor terminal voltage, the starting torque would be the same as that obtained with autotransformer type, but the starting current would be higher, as shown.

Example:
Assuming a project having a 1000 kVA generator, where the voltage variation must not exceed 10%. Can a 75 hp, 1750 rpm, 220-volt, 3-phase, squirrel-cage motor be started without objectionable lamp icker (or 10% voltage drop)? From tables in the circuit protective devices reference section the full-load amperes of this size and type of motor is 158.0 amperes. To convert to same basis as column 7, 158 amperes must be divided by the generator capacity and % voltage drop, or: 158 = 0.0158 amperes per kVA per 1% voltage drop 1000 10 Checking against the table, 0.0158 falls within the .0170 .0146 range. This indicates that a general-purpose motor with autotransformer starting can be used.
Note: Designers may obtain calculated information from engine generator manufacturers.

Short-Cut Method
Column 7 in Table 1.3-11 has been worked out to simplify checking. The gures were obtained by using the formula above and assuming 1 kVA generator capacity and 1% voltage drop.
For more information visit: www.EatonElectrical.com

The calculation results in conservative results. The engineer should provide to the engine-generator vendor the starting kVA of all motors connected to the generator and their starting sequence. The engineer should also specify the maximum allowable drop. The engineer should request that the engine-generator vendor consider the proper generator size when closed-transition autotransformer reduced voltage starters, and soft-start solid-state starter are used; so the most economical method of installation is obtained.

CA08104001E

1.3-22 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0072

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Voltage Drop Formulas

Approximate Method
Voltage Drop E VD = IR cos + IX sin where Abbreviations are same as below Exact Method.

If the receiving end voltage, load current and power factor (PF) are known. E VD = ( E R cos + I R ) + ( E R sin + I X ) E R ER is the receiving end voltage. Exact Method 2 If receiving or sending mVA and its power factor are known at a known sending or receiving voltage.
2 2 ( ZMVA R ) E S = E R + --------------------------------- + 2ZMVA R cos ( R ) 2 ER 2 2 2 2

Exact Methods
Voltage Drop Exact Method 1 If sending end voltage and load PF are known. E VD = E S + IR cos + IX sin E S ( IX cos IR sin ) where: EVD = Voltage drop, line-to-neutral, volts ES I R X = Source voltage, line-to-neutral, volts = Line (Load) current, amperes = Circuit (branch, feeder) resistance, ohms = Circuit (branch, feeder) reactance, ohms
2

or
2 2 2 ( ZMVA R ) E R = E S + --------------------------------- 2ZMVA S cos ( S ) 2 ES

where: ER ES = Receiving Line-Line voltage in kV = Sending Line-Line voltage in kV

cos = Power factor of load, decimal sin = Reactive factor of load, decimal

MVAR = Receiving 3-phase mVA MVAS = Sending 3-phase mVA Z R S = Impedance between and receiving ends = The angle of impedance Z = Receiving end PF = Sending end PF, positive when lagging

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0073

TOC

Index

Power Distribution Systems System Analysis

1.3-23

Master TOC

Voltage Drop
Voltage Drop Tables
Note: Busway voltage drop tables are shown in Section 23 of this catalog.

Table 1.3-12. Temperature Correction Factors for Voltage Drop

Conductor Size Percent Correction Power Factors % 100 No. 14 to No. 4 No. 2 to 3/0 4/0 to 500 kcmil 600 to 1000 kcmil 5.0 5.0 5.0 5.0 90 4.7 4.2 3.1 2.6 80 4.7 3.7 2.6 2.1 70 4.6 3.5 2.3 1.5 60 4.6 3.2 1.9 1.3

To select minimum conductor size:

1. Determine maximum desired voltage drop, in volts. 2. Divide voltage drop by (amperes x circuit feet). 3. Multiply by 100. 4. Find nearest lower voltage drop value in tables, in correct column for type of conductor, conduit and power factor. Read conductor size for that value. 5. Where this results in an oversized cable, verify cable lug sizes for molded case breakers and fusible switches. Where lug size available is exceeded, go to next higher rating.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Tables for calculating voltage drop for copper and aluminum conductors, in either magnetic (steel) or nonmagnetic (aluminum or non-metallic) conduit, appear on Page 1.3-24. These tables give voltage drop per ampere per 100 feet (30 m) of circuit length. The circuit length is from the beginning point to the end point of the circuit regardless of the number of conductors.

Calculations
To calculate voltage drop:
1. Multiply current in amperes by the length of the circuit in feet to get ampere-feet. Circuit length is the distance from the point of origin to the load end of the circuit. 2. Divide by 100. 3. Multiply by proper voltage drop value in tables. Result is voltage drop.

Tables are based on the following conditions:

1. Three or four single conductors in a conduit, random lay. For threeconductor cable, actual voltage drop will be approximately the same for small conductor sizes and high power factors. Actual voltage drop will be from 10 to 15% lower for larger conductor sizes and lower power factors. 2. Voltage drops are phase-to-phase, for 3-phase, 3-wire or 3-phase, 4-wire 60 Hz circuits. For other circuits, multiply voltage drop given in the tables by the following correction factors: 3-phase, 4-wire, phase-to-neutral 1-phase, 2-wire 1-phase, 3-wire, phase-to-phase 1-phase, 3-wire, phase-to-neutral x 0.577 x 1.155 x 1.155 x 0.577

Example:
A 3-phase, 4-wire lighting feeder on a 208-volt circuit is 250 feet (76.2 m) long. The load is 175 amperes at 90% PF. It is desired to use aluminum conductors in aluminum conduit. What size conductor is required to limit the voltage drop to 2% phase-to-phase? 2 1. VD = 208 = 4.16 volts 100 2. 3. = 0.0000951 4.16 175 250 0.0000951 100 = 0.00951

Example:
A 460-volt, 100-hp motor, running at 80% PF, draws 124 amperes full-load current. It is fed by three 2/0 copper conductors in steel conduit. The feeder length is 150 feet (46 m). What is the voltage drop in the feeder? What is the percentage voltage drop? 1. 124 amperes x 150 feet (46 m) = 18,600 ampere-feet 2. Divided by 100 = 186 3. Table: 2/0 copper, magnetic conduit, 80% PF = 0.0187 186 x 0.0187 = 3.48 volts drop 3.48 x 100 = 0.76% drop 460 4. Conclusion: .76% voltage drop is very acceptable (See NEC 2005 Article 215, which suggests that a voltage drop of 3% or less on a feeder is acceptable.)

4. In table, under Aluminum Conductors, nonmagnetic conduit, 90% PF, the nearest lower value is 0.0091. Conductor required is 500 kcmil. (Size 4/0 THW would have adequate ampacity, but the voltage drop would be excessive).

3. Voltage drops are for a conductor temperature of 75C. They may be used for conductor temperatures between 60C and 90C with reasonable accuracy (within 5%). However, correction factors in the table below can be applied if desired. The values in the table are in percent of total voltage drop. For conductor temperature of 60C SUBTRACT the percentage from Table 1.3-12. For conductor temperature of 90C ADD the percentage from Table 1.3-12.

CA08104001E

For more information visit: www.EatonElectrical.com

1.3-24 Power Distribution Systems System Analysis

TOC

Index

June 2006
Sheet 0074

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Table 1.3-13. Voltage Drop Volts per Ampere per 100 Feet (30 m); 3-Phase, Phase-to-Phase
Conductor Size AWG or kcmil Magnetic Conduit (Steel) Load Power Factor, % 60 .3390 .2170 .1390 .0905 .0595 .0399 .0275 .0233 .0198 .0171 .0148 .0130 .0122 .0111 .0104 .0100 .0088 .0084 .0080 .3296 .2133 .1305 .0898 .0595 .0403 .0332 .0286 .0234 .0209 .0172 .0158 .0137 .0130 .0112 .0101 .0095 .0085 70 .3910 .2490 .1590 .1030 .0670 .0443 .0300 .0251 .0211 .0180 .0154 .0134 .0124 .0112 .0104 .0091 .0086 .0081 .0077 .3811 .2429 .1552 .1018 .0660 .0443 .0357 .0305 .0246 .0220 .0174 .0163 .0139 .0133 .0111 .0106 .0094 .0082 80 .4430 .2810 .1790 .1150 .0742 .0485 .0323 .0267 .0222 .0187 .0158 .0136 .0124 .0111 .0102 .0087 .0082 .0077 .0072 .4349 .2741 .1758 .1142 .0747 .0483 .0396 .0334 .0275 .0231 .0179 .0162 .0143 .0128 .0114 .0097 .0090 .0078 90 .4940 .3130 .1980 .1260 .0809 .0522 .0342 .0279 .0229 .0190 .0158 .0133 .0120 .0106 .0096 .0080 .0074 .0069 .0063 .4848 .3180 .1951 .1254 .0809 .0523 .0423 .0350 .0284 .0241 .0177 .0159 .0144 .0131 .0099 .0090 .0084 .0071 100 .5410 .3410 .2150 .1350 .0850 .0534 .0336 .0267 .0213 .0170 .0136 .0109 .0094 .0080 .0069 .0053 .0046 .0040 .0035 .5330 .3363 .2106 .1349 .0862 .0535 .0428 .0341 .0274 .0217 .0170 .0145 .0122 .0100 .0076 .0063 .0056 .0043 Nonmagnetic Conduit (Aluminum or Nonmetallic) Load Power Factor, % 60 .3370 .2150 .1370 .0888 .0579 .0384 .0260 .0218 .0183 .0156 .0134 .0116 .0107 .0097 .0090 .0078 .0074 .0069 .0064 .3312 .2090 .1286 .0887 .0583 .0389 .0318 .0263 .0227 .0160 .0152 .0138 .0126 .0122 .0093 .0084 .0081 .0069 70 .3900 .2480 .1580 .1010 .0656 .0430 .0287 .0238 .0198 .0167 .0141 .0121 .0111 .0099 .0091 .0077 .0072 .0067 .0062 .3802 .2410 .1534 .1011 .0654 .0435 .0349 .0287 .0244 .0171 .0159 .0144 .0128 .0123 .0094 .0085 .0080 .0068 80 .4410 .2800 .1780 .1140 .0730 .0473 .0312 .0256 .0211 .0176 .0147 .0124 .0112 .0099 .0091 .0075 .0070 .0064 .0058 .4328 .2740 .1745 .1127 .0719 .0473 .0391 .0322 .0264 .0218 .0171 .0147 .0133 .0119 .0094 .0085 .0078 .0065 90 .4930 .3120 .1970 .1250 .0800 .0513 .0333 .0270 .0220 .0181 .0149 .0124 .0110 .0096 .0087 .0070 .0064 .0058 .0052 .4848 .3052 .1933 .1249 .0800 .0514 .0411 .0337 .0274 .0233 .0179 .0155 .0132 .0120 .0091 .0081 .0072 .0058 100 .5410 .3410 .2150 .1350 .0849 .0533 .0335 .0266 .0211 .0169 .0134 .0107 .0091 .0077 .0066 .0049 .0042 .0035 .0029 .5331 .3363 .2115 .1361 .0849 .0544 .0428 .0339 .0273 .0222 .0172 .0138 .0125 .0101 .0072 .0060 .0051 .0038

Copper Conductors
14 12 10 8 6 4 2 1 1/0 2/0 3/0 4/0 250 300 350 500 600 750 1000

Aluminum Conductors
12 10 8 6 4 2 1 1/0 2/0 3/0 4/0 250 300 350 500 600 750 1000

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0075

TOC

Index

Power Distribution Systems System Application Considerations

Capacitors
ANSI Standard C37.06 (indoor oilless circuit breakers) indicates the preferred ratings of Eatons Cutler-Hammer Type VCP-W vacuum breaker. For capacitor switching careful attention should be paid to the notes accompanying the table. The denition of the terms are in ANSI Standard C37.04 Article 5.13 (for the latest edition). The application guide ANSI/IEEE Standard C37.012 covers the method of calculation of the quantities covered by C37.06 Standard. Note that the denitions in C37.04 make the switching of two capacitors banks in close proximity to the switchgear bus a back-to-back mode of switching. This classication requires a denite purpose circuit breaker (breakers specically designed for capacitance switching). We recommend that such application be referred to Eaton. A breaker specied for capacitor switching should include as applicable: 1. Rated maximum voltage. 2. Rated frequency. 3. Rated open wire line charging switching current. 4. Rated isolated cable charging and shunt capacitor switching current. 5. Rated back-to-back cable charging and back-to-back capacitor switching current. 6. Rated transient overvoltage factor. 7. Rated transient inrush current and its frequency. 8. Rated interrupting time. 9. Rated capacitive current switching life. 10. Grounding of system and capacitor bank. Loadbreak interrupter switches are permitted by ANSI/IEEE Standard C37.30 to switch capacitance but they must have tested ratings for the purpose. Refer to Cutler-Hammer Type MVS ratings.

1.4-1

Master TOC

Capacitors and Power Factor

Capacitor General Application Considerations
Additional application information is available in Section 37 regarding capacitors and harmonic lters as follows:
s s s s s s

Low Voltage Capacitor Switching

Circuit breakers and switches for use with a capacitor must have a current rating in excess of rated capacitor current to provide for overcurrent from overvoltages at fundamental frequency and harmonic currents. The following percent of the capacitor-rated current should be used as a general guideline: Fused and unfused switches. . . . 165% Molded case breaker or equivalent . . . . . . . . . . . . . . . . . 150% DSII power circuit breakers. . . . . 135% Magnum DS power circuit breaker . . . . . . . . . . . . . . 135% Contactors: Open type . . . . . . . . . . . . . . . . . . . 135% Enclosed type . . . . . . . . . . . . . . . . 150% The NEC, Section 460-8(c), requires the disconnecting means to be rated not less than 135% of the rated capacitor current (for 600 V and below). See Section 37 for switching device ampere ratings. They are based on percentage of capacitor-rated current as indicated (above). The interrupting rating of the switch must be selected to match the system fault current available at the point of capacitor application. Whenever a capacitor bank is purchased with less than the ultimate kvar capacity of the rack or enclosure, the switch rating should be selected based on the ultimate kvar capacity not the initial installed capacity. Refer to Section 37 for recommended selection of capacitor switching devices; recommended maximum capacitor ratings for various motor types and voltages; and for required multipliers to determine capacitor kvars required for Power Factor Correction.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Capacitor selection. Where to install capacitors in a plant distribution system. Locating capacitors on reduced voltage and multi-speed starters. Harmonic considerations. Eliminating harmonic problems. National Electrical Code requirements.

Medium Voltage Capacitor Switching

Capacitance switching constitutes severe operating duty for a circuit breaker. At the time the breaker opens at near current zero the capacitor is fully charged. After interruption, when the alternating voltage on the source side of the breaker reaches its opposite maximum, the voltage that appears across the contacts of the open breaker is at least twice the normal peak lineto-neutral voltage of the circuit. If a breakdown occurs across the open contact the arc is reestablished. Due to the circuit constants on the supply side of the breaker, the voltage across the open contact can reach three times the normal line-to-neutral voltage. After it is interrupted and with subsequent alternation of the supply side voltage, the voltage across the open contact is even higher.

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-2

Power Distribution Systems System Application Considerations

Capacitors

TOC

Index

June 2006
Sheet 0076

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Motor Power Factor Correction

See Section 37 containing suggested maximum capacitor ratings for induction motors switched with the capacitor. The data is general in nature and representative of general purpose induction motors of standard design. The preferable means to select capacitor ratings is based on the maximum recommended kvar information available from the motor manufacturer. If this is not possible or feasible, the tables can be used. An important point to remember is that if the capacitor used with the motor is too large, self-excitation may cause a motor-damaging overvoltage when the motor and capacitor combination is disconnected from the line. In addition, high transient torques capable of damaging the motor shaft or coupling can occur if the motor is reconnected to the line while rotating and still generating a voltage of self-excitation.

% AR percent reduction in line current due to the capacitor. A capacitor located on the motor side of the overload relay reduces line current through the relay. Therefore, a different overload relay and/or setting may be necessary. The reduction in line current may be determined by measuring line current with and without the capacitor or by calculation as follows: (Original PF) % AR = 100 100 (Improved PF) If a capacitor is used with a lower kvar rating than listed in tables, the % AR can be calculated as follows: Actual kvar % AR = Listed % AR kvar in Table The tables can also be used for other motor ratings as follows: A. For standard 60 Hz motors operating at 50 Hz: kvar = 1.7 1.4 of kvar listed % AR = 1.8 1.35 of % AR listed B. For standard 50 Hz motors operating at 50 Hz: kvar = 1.4 1.1 of kvar listed % AR = 1.4 1.05 of % AR listed C. For standard 60 Hz wound-rotor motors: kvar = 1.1 of kvar listed % AR= 1.05 of % AR listed
Note: For A, B, C, the larger multipliers apply for motors of higher speeds; i.e., 3600 rpm = 1.7 mult., 1800 rpm = 1.65 mult., etc.

To derate a capacitor used on a system voltage lower than the capacitor voltage rating, such as a 240-volt capacitor used on a 208-volt system, use the following formula:
Actual kvar =
( Applied Voltage ) Nameplate kvar --------------------------------------------------------------------2 ( Nameplate Voltage )
2

For the kVAC required to correct the power factor from a given value of COS 1 to COS 2, the formula is: kVAC = KW (tan phase1 tan phase2) Capacitors cause a voltage rise. At light load periods the capacitive voltage rise can raise the voltage at the location of the capacitors to an unacceptable level. This voltage rise can be calculated approximately by the formula MVA r % VR = MVA SC MVAR is the capacitor rating and MVASC is the system short circuit capacity. With the introduction of variable speed drives and other harmonic current generating loads, the capacitor impedance value determined must not be resonant with the inductive reactances of the system.

Denitions
kvar rating of the capacitor in reactive kilovolt-amperes. This value is approximately equal to the motor no-load magnetizing kilovars.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0077

TOC

Index

Power Distribution Systems System Application Considerations

Protection and Coordination
damage or withstand characteristics, (e) calculation of maximum short circuit currents (and ground fault currents if ground fault protection is included) available at each protective device location, (f) understanding of operating characteristics and available adjustments of each protective device, (g) any special overcurrent protection requirements including utility limitations. Refer to (Figure 1.4-1). To ensure complete coordination, the time-trip characteristics of all devices in series should be plotted on a single sheet of standard log-log paper. Devices of different-voltage systems can be plotted on the same sheet by converting their current scales, using the voltage ratios, to the same voltagebasis. Such a coordination plot is shown in Figure 1.4-1. In this manner, primary fuses and circuit breaker relays on the primary side of a substation transformer can be coordinated with the low voltage breakers. Transformer damage points, based on ANSI standards, and low voltage cable heating limits can be plotted on this set of curves to assure that apparatus limitations are not exceeded. Ground-fault curves may also be included in the coordination study if ground-fault protection is provided, but care must be used in interpreting their meaning. Standard denitions have been established for overcurrent protective devices covering ratings, operation and application systems. M Motor (100 hp). Dashed line shows initial inrush current, starting current during 9-sec. acceleration, and drop to 124 A normal running current, all well below CB A trip curve.

1.4-3

Master TOC

Overcurrent Protection and Coordination

Overcurrents in a power distribution system can occur as a result of both normal (motor starting, transformer inrush, etc.) and abnormal (overloads, ground fault, line-to-line fault, etc.) conditions. In either case, the fundamental purposes of current-sensing protective devices are to detect the abnormal overcurrent and with proper coordination, to operate selectively to protect equipment, property and personnel while minimizing the outage of the remainder of the system. With the increase in electric power consumption over the past few decades, dependence on the continued supply of this power has also increased so that the direct costs of power outages have risen signicantly. Power outages can create dangerous and unsafe conditions as a result of failure of lighting, elevators, ventilation, re pumps, security systems, communications systems, and the like. In addition, economic loss from outages can be extremely high as a result of computer downtime, or, especially in industrial process plants, interruption of production. Protective equipment must be adjusted and maintained in order to function properly when an overcurrent occurs, but coordination begins during power system design with the knowledgeable analysis and selection and application of each overcurrent protective device in the series circuit from the power source(s) to each load apparatus. The objective of coordination is to localize the overcurrent disturbance so that the protective device closest to the fault on the power-source side has the rst chance to operate; but each preceding protective device upstream toward the power source should be capable, within its designed settings of current and time, to provide backup and de-energize the circuit if the fault persists. Sensitivity of coordination is the degree to which the protective devices can minimize the damage to the faulted equipment. To study and accomplish coordination requires (a) a one-line diagram, the roadmap of the power distribution system, showing all protective devices and the major or important distribution and utilization apparatus, (b) identication of desired degrees of power continuity or criticality of loads throughout system, (c) denition of operating-current characteristics (normal, peak, starting) of each utilization circuit, (d) equipment
CA08104001E

i ii 1 2 3 4 5 6 7

SCALE X 100 = CURRENT IN AMPERES AT 480 VOLTS

1000 900 800 700 600 500 400 300 .5 .6 .7 .8 .9 1 2 3 4 5 6 7 8 9 10 20 30 40 50 60 6000 7000 8000 9000 10,000 1000 900 800 700 600 500 400 600 700 800 900 1000 2000 3000 4000 5000 70 80 90 100 200 300 400 500

4.16 kV

250 MVA

8 9 10 11 12 13 14 15 16 17

B A C D D

300

200

200

100 90 80 70 60 50 40 30 20

250 Amperes 1000 kVA 5.75% ANSI 3-Phase Thru Fault Protection Curve (More Than 10 in Lifetime) 4,160 V 480/277 V 19,600 Amperes

100 90 80 70 60 50 40 30

1,600 Amperes 24,400 Amperes 600 Amperes

20

TIME IN SECONDS

10 9 8 7 6 5 4 3

B M

10 9 8 7 6 5 4 3

TIME IN SECONDS

20,000 Amperes A 175 Amperes

1 .9 .8 .7 .6 .5 .4 .3

100 hp 124 Amperes FLC

1 .9 .8 .7 .6 .5

X = Available fault current including motor contribution. Ground Fault Trip C

.4 .3

.2

.2

.1 .09 .08 .07 .06 .05 .04 .03

Transformer Inrush Max. 3-Phase 4.16 kV Fault

.1 .09 .08 .07 .06 .05 .04 .03 .02

18 19 20 21

.02

.5 .6 .7 .8 .9 1

6 7 8 9 10

20

30

40 50 60

SCALE X 100 = CURRENT IN AMPERES AT 480 VOLTS

Figure 1.4-1. Time-Current Characteristic Curves for Typical Power Distribution System Protective Devices Coordination Analysis
For more information visit: www.EatonElectrical.com

6000 7000 8000 9000 10,000

600 700 800 900 1000

2000

3000

4000

5000

70 80 90 100

200

300

400

500

.01

Max. 480V Fault

.01

1.4-4

Power Distribution Systems System Application Considerations

Protection and Coordination
A CB (175 A) coordinates selectively with motor M on starting and running and with all upstream devices, except that CB B will trip rst on low level ground faults. B CB (600 A) coordinates selectively with all upstream and downstream devices, except will trip before A on limited ground faults, since A has no ground fault trips. C Main CB (1600 A) coordinates selectively with all downstream devices and with primary fuse D, for all faults on load side of CB. D Primary fuse (250 A, 4,160 V) coordinates selectively with all secondary protective devices. Curve converted to 480 V basis. Clears transformer inrush point (12 x FLC for 0.1 sec.), indicating that fuse will not blow on inrush. Fuse is underneath right-half of ANSI 3-phase withstand curve, indicating fuse will protect transformer for high-magnitude faults up to ANSI rating. Delta-Wye secondary side short circuit is not reected to the primary by the relation VS I P = I S VP Maximum 480 V 3-phase fault indicated on the horizontal current axis.

TOC

Index

June 2006
Sheet 0078

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Maximum 4160 V 3-phase fault indicated, converted to 480 V basis.

4160 I 480 V = I 4160 V 480 The ANSI protection curves are specied in ANSI C57.109 for liquid-lled transformers and C57.12.59 for dry-type transformers. Illustrative examples such as shown here start the coordination study from the lowest rated device proceeding upstream. In practice the setting or rating of the utilitys protective device sets the upper limit. Even in cases where the customer owns the medium voltage or higher distribution system, the setting or rating of the lowest set protective device at the source determines the settings of the downstream devices and the coordination. Therefore the coordination study should start at the present setting or rating of the upstream device and work towards the lowest rated device. If this procedure results in unacceptable settings, the setting or rating of the upstream device should be reviewed. Where the utility is the sole source they should be consulted. Where the owner has its own medium or higher voltage distribution the settings or ratings of all upstream devices should be checked. If perfect coordination is not feasible, then lack of coordination should be limited to the smallest part of the system. Application data is available for all protective equipment to permit systems to be designed for adequate overcurrent protection and coordination. For circuit breakers of all types, time-current curves permit selection of instantaneous and inverse-time trips. For more complex circuit breakers, with solid state trip units, trip curves include long- and short-time delays, as well as ground-fault tripping, with a wide range of settings and features to provide selectivity and coordination. For current-limiting circuit breakers, fuses, and circuit breakers with integral fuses, not only are time-current characteristic curves available, but also data on current-limiting per-formance and protection for downstream devices.

In a fully rated system, all circuit breakers must have an interrupting capacity adequate for the maximum available fault current at their point of application. All breakers are equipped with long-time-delay (and possibly short delay) and instantaneous overcurrent trip devices. A main breaker may have short time-delay tripping to allow a feeder breaker to isolate the fault while power is maintained to all the remaining feeders. A selective or fully coordinated system permits maximum service continuity. The tripping characteristics of each overcurrent device in the system must be selected and set so that the breaker nearest the fault opens to isolate the faulted circuit, while all other breakers remain closed, continuing power to the entire unfaulted part of the system. The 2005 National Electrical Code (NEC) has added specic requirements for designing certain circuits with selective coordination. Article 100 has added, under Coordination (Selective), the following denition: Localization of an overcurrent condition to restrict outages to the circuit or equipment affected, accomplished by the choice of overcurrent protective devices and their ratings or settings.
NEC 2005 NFPA 70: National Electrical Code International Electrical Code Series.

for L-L and L-G faults. For line-to-line fault the secondary (low voltage) side fault current is 0.866 x I 3-phase fault current.
However the primary (high voltage) side fault is the same as if the secondary fault was a 3-phase fault. Therefore in coordination studies, the knee of the short-time pickup setting on the secondary breaker should be multiplied by 1 or 1.1547 0.866 before it is compared to the minimum melting time of the upstream primary fuse curve. In the example shown, the knee is at 4000 amperes 30 sec., and the 30-sec. trip time should be compared to the MMT (minimum melt time) of the fuse curve at 4000 x 1.1547 = 4619 amperes. In this case there is adequate clearance to the fuse curve.

Article 620.62 (Elevators, Dumbwaiters, Escalators, Moving Walks, Wheelchair Lifts, and Stairway Chair Lifts) requires Where more than one driving machine disconnecting means is supplied by a single feeder, the overcurrent protective devices in each disconnecting means shall be selectively coordinated with any other supply side overcurrent protective device. A similar requirement under Article 700.27 is as follows; Emergency system(s) overcurrent devices shall be selectively coordinated with all supply side overcurrent protective devices. Also Article 701.18, added Legally required standby system(s) overcurrent devices shall be selectively coordinated with all supply side overcurrent devices. In addition, for health care facilities, Article 517.26, Application of Other Articles requires that The essential electrical system shall meet the requirements of Article 700, except as amended by Article 517.

In the example shown, the ANSI 3-phase through fault protection curve must be multiplied by 0.577 and replotted in order to determine the protection given by the primary for a single line to ground fault in the secondary.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0079

TOC

Index

Power Distribution Systems System Application Considerations

Protection and Coordination

1.4-5

Master TOC

All breakers must have an interrupting capacity not less than the maximum available short circuit current at their point of application. A selective system is a fully rated system with tripping devices chosen and adjusted to provide the desired selectivity. The tripping characteristics of each overcurrent device should not overlap, but should maintain a minimum time interval for devices in series (to allow for normal operating tolerances) at all current values. Generally, a maximum of four low voltage circuit breakers can be operated selectively in series, with the feeder or branch breaker downstream furthest from the source. Specify true rms sensing devices in order to avoid false trips due to rapid currents or spikes. Specify tripping elements with I2t or I4t feature for improved coordination with other devices having I2t or I4t (such as OPTIM trip units) characteristics, and fuses. In general for systems such as shown in the example: 1. The settings or ratings of the primary side fuse and main breaker must not exceed the settings allowed by NEC Article 450. 2. At 12 x IFL the minimum melting time characteristic of the fuse should be higher than 0.1 second. 3. 4. The primary fuse should be to the left of the transformer damage curve as much as possible. The correction factor for a single lineto-ground factor must be applied to the damage curve. 5. The setting of the short-time delay element must be checked against the fuse MMT after it is corrected for line-to-line faults. 6. The maximum fault current must be indicated at the load side of each protective device. 7. The setting of a feeder protective device must comply with Article 240 and Article 430 of the NEC. It also must allow the starting and acceleration of the largest motor on the feeder while carrying all the other loads on the feeder.

Protection of Conductors (Excerpts from NEC 240.4)

Conductors, other than exible cords and xture wires, shall be protected against overcurrent in accordance with their ampacities as specied in Section 310-15, unless otherwise permitted or required in (A) through (G). A. Power Loss Hazard. Conductor overload protection shall not be required where the interruption of the circuit would create a hazard, such as in a material handling magnet circuit or re pump circuit. Short circuit protection shall be provided.
Note: FPN See NFPA 20-2003, standard for the Installation of Stationary Pumps for Fire Protection.

E. Tap Conductors. Tap conductors shall be permitted to be protected against overcurrent in accordance with the following: 1. 210-19(A)(3) and (A)(4) Household Ranges and Cooking Appliances and Other Loads. 2. 240.5(B)(2) Fixture Wire. 3. 240.21 Location in Circuit. 4. 368.17(B) Reduction in Ampacity Size of Busway. 5. 368.17(C) Feeder or Branch Circuits (busway taps). 6. 430.53(D) Single Motor Taps.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Circuit Breaker Cable Temperature Ratings

UL listed circuit breakers rated 125 A or less shall be marked as being suitable for 60C (140F), 75C (167F) only or 60/75C (140/167F) wire. All CutlerHammer breakers rated 125 A or less are marked 60/75C. All UL listed circuit breakers rated over 125 A are suitable for 75C conductors. Conductors rated for higher temperatures may be used, but must not be loaded to carry more current than the 75C ampacity of that size conductor for equipment marked or rated 75C or the 65C ampacity of that size conductor for equipment marked or rated 65C. However, when applying derated factors, so long as the actual load does not exceed the lower of the derated ampacity or the 75C or 60C ampacity that applies.

B. Devices Rated 800 Amperes or Less. The next higher standard overcurrent device rating (above the ampacity of the conductors being protected) shall be permitted to be used, provided all of the following conditions are met. 1. The conductors being protected are not part of a multi-outlet branch circuit supplying receptacles for cord- and plug-connected portable loads. 2. The ampacity of the conductors does not correspond with the standard ampere rating of a fuse or a circuit breaker without overload trip adjustments above its rating (but that shall be permitted to have other trip or rating adjustments). 3. The next higher standard rating selected does not exceed 800 amperes. C. Devices Rated Over 800 Amperes. Where the overcurrent device is rated over 800 amperes, the ampacity of the conductors it protects shall be equal to or greater than the rating of the overcurrent device as dened in Section 240.6. D. Small Conductors. Unless specically permitted in 240.4(E) or 240.4(G), the overcurrent protection shall not exceed 15 amperes for 14 AWG, 20 amperes for 12 AWG, and 30 amperes for 10 AWG copper; or 15 amperes for 12 AWG and 25 amperes for 10 AWG aluminum and copper-clad aluminum after any correction factors for ambient temperature and number of conductors have been applied.

Zone Selective Interlocking

Trip elements equipped with zone selective interlocking, trip without intentional time delay unless a restraint signal is received from a protective device downstream. Breakers equipped with this feature reduce the damage at the point of fault if the fault occurs at a location between the zone of protection. The upstream breaker upon receipt of the restraint signal will not trip until its time-delay setting times out. If the breaker immediately downstream of the fault does not open, then after timing out, the upstream breaker will trip. Breakers equipped with ground fault trip elements should also be specied to include zone interlocking for the ground fault trip element.

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-6

Power Distribution Systems System Application Considerations

Protection and Coordination

TOC

Index

June 2006
Sheet 0080

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Ground Fault Protection

Article 230-95 of NEC requires groundfault protection of equipment shall be provided for solidly grounded wye electrical services of more than 150 volts to ground, but not exceeding 600 volts phase-to-phase for each service disconnect rated 1000 amperes or more. The rating of the service disconnect shall be considered to be the rating of the largest fuse that can be installed or the highest continuous current trip setting for which the actual overcurrent device installed in a circuit breaker is rated or can be adjusted. The maximum allowable settings are: 1200 amperes pickup, 1 second or less trip delay at currents of 3000 amperes or greater. The characteristics of the ground-fault trip elements create coordination problems with downstream devices not equipped with ground fault protection. The National Electrical Code exempts re pumps and continuous industrial processes from this requirement.

Suggested Ground Fault Settings

For the main devices: A ground fault pickup setting equal to 20 30% of the main breaker rating but not to exceed 1200 amperes, and a time delay equal to the delay of the short time element, but not to exceed 1 second. For the feeder ground fault setting: A setting equal to 20 30% of the feeder ampacity and a time delay to coordinate with the setting of the main (at least 6 cycles below the main). If the desire to selectively coordinate ground fault devices results in settings which do not offer adequate damage protection against arcing single lineground faults, the design engineer should decide between coordination and damage limitation. For low voltage systems with highmagnitude available short circuit currents, common in urban areas and large industrial installations, several solutions are available. High interrupting Series C molded case breakers, current-limiting circuit breakers, or current-limiting fuses, limiters integral with molded-case circuit breakers (TRI-PAC ) or mounted on power circuit breakers (MDSL) can be used to handle these large fault currents. To provide current limiting, these devices must clear the fault completely within the rst half-cycle, limiting the peak current (Ip) and heat energy (I2t) letthrough to considerably less than what would have occurred without the device. For a fully fusible system, rule-of-thumb fuse ratios or more accurate I2t curves can be used to provide selectivity and coordination. For fusebreaker combinations, the fuse should be selected (coordinated) so as to permit the breaker to handle those overloads and faults within its capacity; the fuse should operate before or with the breaker only on large faults, approaching the interrupting capacity of the breaker, to minimize fuse blowing. Recently, unfused, truly current-limiting circuit breakers with interrupting ratings adequate for the largest systems (Type Series C, FDC, JDC, KDC, LDC and NDC frames or Type Current Limit-R ) have become available.

Any of these current-limiting devices fuses, fused breakers, or currentlimiting breakers cannot only clear these large faults safely, but also will limit the Ip and I2t let-through signicantly to prevent damage to apparatus downstream, extending their zone of protection. Without the current limitation of the upstream device, the fault current could exceed the withstand capability of the downstream equipment. Underwriters Laboratories tests and lists these series combinations. Application information is available for combinations which have been tested and UL -listed for safe operation downstream from MDSL, TRI-PAC, and Current Limit-R, or Series C breakers of various ratings, under high available fault currents. Protective devices in electrical distribution systems may be properly coordinated when the systems are designed and built, but that is no guarantee that they will remain coordinated. System changes and additions, plus power source changes, frequently modify the protection requirements, sometimes causing loss of coordination and even increasing fault currents beyond the ratings of some devices. Consequently, periodic study of protective-device settings and ratings is as important for safety and preventing power outages as is periodic maintenance of the distribution system.

It is recommended that in solidly grounded 480/277-volt systems where main breakers are specied to be equipped with ground fault trip elements that the feeder breakers be specied to be equipped with ground fault trip elements as well.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0081

TOC

Index

Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection
with such an object while grounded could be seriously injured or killed. In addition, current ow from the accidental grounding of an energized part of the system could generate sufcient heat (often with arcing) to start a re. To prevent the establishment of such unsafe potential difference requires that (1) the equipment grounding conductor provide a return path for ground fault currents of sufciently low impedance to prevent unsafe voltage drop, and (2) the equipment grounding conductor be large enough to carry the maximum ground fault current, without burning off, for sufcient time to permit protective devices (ground fault relays, circuit breakers, fuses) to clear the fault. The grounded conductor of the system (usually the neutral conductor), although grounded at the source, must not be used for equipment grounding. The equipment grounding conductor may be the metallic conduit or raceway of the wiring system, or a separate equipment grounding conductor, run with the circuit conductors, as permitted by NEC. If a separate equipment grounding conductor is used, it may be bare or insulated; if insulated, the insulation must be green, green with yellow stripe or green tape. Conductors with green insulation may not be used for any purpose other than for equipment grounding. The equipment grounding system must be bonded to the grounding electrode at the source or service; however, it may be also connected to ground at many other points. This will not cause problems with the safe operation of the electrical distribution system. Where computers, data processing, or microprocessorbased industrial process control systems are installed, the equipment grounding system must be designed to minimize interference with their proper operation. Often, isolated grounding of this equipment, or isolated electrical supply systems are required to protect microprocessors from power system noise that does not in any way affect motors or other electrical equipment. Such systems must use single-point ground concept to minimize noise and still meet the NEC requirements. Any separate isolated ground mat must be tied to the rest of the facility ground mat system for NEC compliance.

1.4-7

Master TOC

Grounding
Grounding encompasses several different but interrelated aspects of electrical distribution system design and construction, all of which are essential to the safety and proper operation of the system and equipment supplied by it. Among these are equipment grounding, system grounding, static and lightning protection, and connection to earth as a reference (zero) potential.

i ii 1 2 3 4 5 6 7 8 9 10 11 12

1. Equipment Grounding
Equipment grounding is essential to safety of personnel. Its function is to ensure that all exposed noncurrentcarrying metallic parts of all structures and equipment in or near the electrical distribution system are at the same potential, and that this is the zero reference potential of the earth. Equipment grounding is required by both the National Electrical Code (Article 250) and the National Electrical Safety Code regardless of how the power system is grounded. Equipment grounding also provides a return path for ground fault currents, permitting protective devices to operate. Accidental contact of an energized conductor of the system with an improperly grounded noncurrent-carry metallic part of the system (such as a motor frame or panelboard enclosure) would raise the potential of the metal object above ground potential. Any person coming in contact

2. System Grounding
System grounding connects the electrical supply, from the utility, from transformer secondary windings, or from a generator, to ground. A system can be solidly grounded (no intentional impedance to ground), impedance grounded (through a resistance or reactance), or ungrounded (with no intentional connection to ground.

3. Medium Voltage System: Grounding

Table 1.4-1. Features of Ungrounded and Grounded Systems (from ANSI C62.92)
Description (1) Apparatus Insulation (2) Fault to Ground Current A Ungrounded Fully insulated Usually low B Solidly Grounded Lowest C Reactance Grounded Partially graded D Resistance Grounded Partially graded Low E Resonant Grounded Partially graded Negligible except when Petersen coil is short circuited for relay purposes when it may compare with solidlygrounded systems Is eliminated from consideration during single line-to-ground faults unless neutralizer is short circuited to isolate fault by relays Requires special provisions but can be made satisfactory Unlikely Effect of faults transmitted as excess voltage on sound phases to all parts of conductively connected network Seem to be more likely but conclusive information not available

13 14 15 16 17 18 19 20 21

Maximum value rarely Cannot satisfactorily be higher than 3-phase short reduced below one-half circuit current or one-third of values for solid grounding

(3) Stability

Usually unimportant

Lower than with other methods but can be made satisfactory by use of high-speed breakers

Improved over solid grounding particularly if used at receiving end of system

Improved over solid grounding particularly if used at receiving end of system

(4) Relaying

Difcult

Satisfactory

Satisfactory

Satisfactory

(5) Arcing Grounds (6) Localizing Faults

Likely

Unlikely

Possible if reactance is excessive Effect of faults localized to system or part of system where they occur unless reactance is quite high Unlikely unless reactance is quite high and insulation weak

Unlikely Effect of faults transmitted as excess voltage on sound phases to all parts of conductively connected network Unlikely unless resistance is quite high and insulation weak

Effect of fault transmitted Effect of faults localized as excess voltage on to system or part of sound phases to all system where they occur parts of conductively connected network Likely Likely

(7) Double Faults

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-8

Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection
Table 1.4-1. Features of Ungrounded and Grounded Systems (Continued)
Description (8) Lightning Protection A Ungrounded B Solidly Grounded C Reactance Grounded If reactance is very high arresters for ungrounded neutral service must be applied at sacrice in cost and efciency Will be reduced from solidly grounded values

TOC

Index

June 2006
Sheet 0082

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12

D Resistance Grounded Arresters for ungrounded, neutral service usually must be applied at sacrice in cost and efciency Will be reduced from solidly grounded values

E Resonant Grounded Ungrounded neutral service arresters must be applied at sacrice in cost and efciency Will be low in magnitude except in cases of double faults or series resonance at harmonic frequencies, but duration may be great May be high during faults

Ungrounded neutral Highest efciency and service arresters must be lowest cost applied at sacrice in cost and efciency Will usually be low except in cases of double faults or electrostatic induction with neutral displaced but duration may be great Will be greatest in magnitude due to higher fault currents but can be quickly cleared particularly with high speed breakers

(9) Telephone Interference

(10) Radio Interference (11) Line Availability

May be quite high during Minimum faults or when neutral is displayed Will inherently clear Must be isolated for themselves if total length each fault of interconnected line is low and require isolation from system in increasing percentages as length becomes greater

Greater than for solidly grounded, when faults occur Must be isolated for each fault

Greater than for solidly grounded, when faults occur Must be isolated for each fault

Need not be isolated but will inherently clear itself in about 60 to 80 percent of faults

(12) Adaptability to Interconnection

Cannot be interconnected Satisfactory indenitely Satisfactory indenitely unless interconnecting with reactance-grounded with solidly-grounded system is ungrounded systems systems or isolating transformers are used

Satisfactory with solidlyor reactance-grounded systems with proper attention to relaying

Cannot be interconnected unless interconnected system is resonant grounded or isolating transformers are used. Requires coordination between interconnected systems in neutralizer settings Interrupting capacity determined by 3-phase fault conditions

(13) Circuit Breakers

Interrupting capacity determined by 3-phase conditions

Same interrupting capacity as required for 3-phase short circuit will practically always be satisfactory Simple

Interrupting capacity determined by 3-phase fault conditions

Interrupting capacity determined by 3-phase fault conditions

(14) Operating Procedure

Ordinarily simple but possibility of double faults introduces complication in times of trouble

Simple

Simple

Taps on neutralizers must be changed when major system switching is performed and difculty may arise in interconnected systems. Difcult to tell where faults are located Highest unless the arc suppressing characteristic is relied on to eliminate transmission circuits when it may be lowest for the particular types of service

(15) Total Cost

13 14 15 16 17 18 19 20 21

High, unless conditions Lowest are such that arc tends to extinguish itself, when transmission circuits may be eliminated, reducing total cost

Intermediate

Intermediate

Because the method of grounding affects the voltage rise of the unfaulted phases above ground, ANSI C62.92 classies systems from the point of view of grounding in terms of a coefcient of grounding
Highest Power Frequency rms Line Ground Voltage COG = -------------------------------------------------------------------------------------------rms Line Line Voltage at Fault Location with the Fault Removed

This same standard also denes systems as effectively grounded when COG .8 such a system would have X0 /X1 3.0 and R0 /X1 1.0. Any other grounding means that does not satisfy these conditions at any point in a system is not effectively grounded.

The aforementioned denition is of signicance in medium voltage distribution systems with long lines and with grounded sources removed during light load periods so that in some locations in the system the X0 /X1, R0 /X1 may exceed the dening limits. Other standards (cable and lightning arrester) allow the use of 100% rated cables and arresters selected on the basis of an effectively grounded system only where the criteria in the above are met. In effectively grounded system the line-to-ground fault current is high and there is no signicant voltage rise in the unfaulted phases. With selective ground fault isolation the fault current should be at least 60%

of the 3-phase current at the point of fault. Damage to cable shields must be checked. Although this fact is not a problem except in small cables, it is a good idea to supplement the cable shields returns of ground fault current to prevent damage, by installing an equipment grounding conductor. The burdens on the current transformers must be checked also (for saturation considerations), where residually connected ground relays are used and the current transformers supply current to phase relays and meters. If ground sensor current transformers (zero sequence type) are used they must be of high burden capacity.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0083

TOC

Index

Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection
current transformers rating of the source. This rule will provide sensitive differential protection for wye-connected generators and transformers against line-to-ground faults near the neutral. Of course, if the installation of ground fault differential protection is feasible, or ground sensor current transformers are used, sensitive differential relaying in resistance grounded system with greater fault limitation is feasible. In general, ground sensor current transformers (zero sequence) do not have high burden capacity. Resistance grounded systems limit the circulating currents of triple harmonics and limit the damage at the point of fault. This method of grounding is not suitable for line-to-neutral connection of loads. On medium voltage systems, 100% cable insulation is rated for phase-toneutral voltage. If continued operation with one phase faulted to ground is desired, increased insulation thickness is required. For 100% insulation, fault clearance is recommended within one minute; for 133% insulation, one hour is acceptable; for indenite operation, as long as necessary, 173% insulation is required.

1.4-9

Master TOC

Table 1.4-2 taken from ANSI-C62.92 indicates the characteristics of the various methods of grounding.

Grounding Point
The most commonly used grounding point is the neutral of the system or the neutral point created by means of a zigzag or a wye-broken delta grounding transformer in a system which was operating as an ungrounded delta system.
In general, it is a good practice that all source neutrals be grounded with the same grounding impedance magnitude. However, neutrals should not be tied together to a single resistor. Where one of the medium voltage sources is the utility, their consent for impedance grounding must be obtained. The neutral impedance must have a voltage rating at least equal to the rated line-to-neutral voltage class of the system. It must have at least a 10-second rating equal to the maximum future line-to-ground fault current and a continuous rating to accommodate the triple harmonics that may be present.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Reactance Grounding
It is generally used in the grounding of the neutrals of generators directly connected to the distribution system bus, in order to limit the line-to-ground fault to somewhat less than the 3-phase fault at the generator terminals. If the reactor is so sized, in all probability the system will remain effectively grounded.

Resistance Grounded
Medium voltage systems in general should be low resistance grounded. The ground fault is typically limited to about 200 400 A but less than 1000 amperes (a cable shield consideration). With a properly sized resistor and relaying application, selective fault isolation is feasible. The fault limit provided has a bearing on whether residually connected relays are used or ground sensor current transformers are used for ground fault relaying. In general, where residually connected ground relays are used (51N), the fault current at each grounded source should not be limited to less than the Table 1.4-2. Characteristics of Grounding
Grounding Classes and Means A. Effectively 1. Effective 2. Very effective B. Noneffectively 1. Inductance a. Low Inductance b. High Inductance 2. Resistance a. Low Resistance b. High Resistance 3. Inductance and Resistance 4. Resonant 5. Ungrounded/Capacitance a. Range A b. Range B

4. Low Voltage System: Grounding

Solidly grounded 3-phase systems (Figure 1.4-2) are usually wyeconnected, with the neutral point grounded. Less common is the redleg or high-leg delta, a 240 V system supplied by some utilities with one winding center-tapped to provide 120 V to ground for lighting. This 240 V, 3-phase, 4-wire system is used where 120 V lighting load is small compared to 240 V power load, because the installation is low in cost to the utility. A corner-grounded 3-phase delta system is sometimes found, with one phase grounded to stabilize all voltages to ground. Better solutions are available for new installations.
Phase A Phase B Phase C Neutral

Ratios of Symmetrical Component Parameters X0/X1 0-3 0-1 R0/X1 0-1 0-0.1 R0/X0

Percent Fault Current

Per Unit Transient LG Voltage

>60 >95

2 <1.5

3-10 >10 0-10 >10

0-1 >100

<2 2 (-1) >2

>25 <25 <25 <1 <10 <1 <8 >8

<2.3 2.73 <2.5 2.73 2.73 2.73 3 >3

- to -40 -40 to 0

N
Grounded Wye

Values of the coefcient of grounding (expressed as a percentage of maximum phase-to-phase voltage) corresponding to various combinations of these ratios are shown in the ANSI C62.92 Appendix gures. Coefcient of grounding affects the selection of arrester ratings. Ground-fault current in percentage of the 3-phase short circuit value. Transient line-to-ground voltage, following the sudden initiation of a fault in per unit of the crest of the prefault line-to-ground operating voltage for a simple, linear circuit. In linear circuits, Class A1 limits the fundamental line-to-ground voltage on an unfaulted phase to 138% of the prefault voltage; Class A2 to less than 110%. See ANSI 62.92 para. 7.3 and precautions given in application sections. Usual isolated neutral (ungrounded) system for which the zero-sequence reactance is capacitive (negative). Same as NOTE (6) and refer to ANSI 62.92 para. 7.4. Each case should be treated on its own merit. Under restriking arcing ground fault conditions (e.g., vacuum breaker interrupter operation), this value can approach 500%. Under arcing ground fault conditions, this value can easily reach 700% but is essentially unlimited.

Phase B Phase C Phase A Neutral

17 18

Center-Tapped (High-Leg) Delta Phase A Phase B Phase C

19 20 21

Corner-Grounded Delta

Figure 1.4-2. Solidly Grounded Systems

CA08104001E For more information visit: www.EatonElectrical.com

1.4-10 Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection
Ungrounded systems (Figure 1.4-3) can be either wye or delta, although the ungrounded delta system is far more common.

TOC

Index

June 2006
Sheet 0084

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12

Selecting the Low Voltage System Grounding Method

There is no one best distribution system for all applications. In choosing among solidly grounded, resistance grounded, or ungrounded power distribution, the characteristics of the system must be weighed against the requirements of power loads, lighting loads, continuity of service, safety, and cost. Under ground fault conditions, each system behaves very differently. A solidly grounded system produces high fault currents, usually with arcing, and the faulted circuit must be cleared on the rst fault within a fraction of a second to minimize damage. An ungrounded system will pass limited current into the rst ground fault only the charging current of the system, caused by the distributed capacitance to ground of the system wiring and equipment. In low voltage systems, this is rarely more than 1 or 2 amperes. Therefore, on rst ground fault an ungrounded system can continue in service, making it desirable where power outages cannot be tolerated. However, if the ground fault is intermittent, sputtering or arcing, a high voltage as much as 6 to 8 times phase voltage can be built up across the system capacitance, from the phase conductors to ground. Similar high voltages can occur as a result of resonance between system capacitance and the inductances of transformers and motors in the system. The phase-to-phase voltage is not affected. This high transient phase-to-ground voltage can puncture insulation at weak points, such as motor windings, and is a frequent cause of multiple motor failures on ungrounded systems. Locating a rst fault on an ungrounded system can be difcult. If, before the rst fault is cleared, a second ground fault occurs on a different phase, even on a different, remote feeder, it is a high-current phase-toground-to-phase fault, usually arcing, that can cause severe damage if at least one of the grounds is not cleared immediately. If the second circuit is remote, enough current may not ow to cause protection to operate. This can leave high voltages and stray currents on structures and jeopardize personnel. In general, where loads will be connected line-to-neutral, solidly grounded systems are used. High resistance grounded systems are used as substitutes for ungrounded systems where high system availability is required.
For more information visit: www.EatonElectrical.com

Ungrounded Delta

With one phase grounded, the voltage to ground of the other two phases rises 73%, to full phase-to-phase voltage. In low voltage systems this is not important, since conductors are insulated for 600 V. A low voltage resistance grounded system is normally grounded so that the single line-to-ground fault current exceeds the capacitive charging current of the system. If data for the charging current is not available use 40 50 ohm resistor in the neutral of the transformer. In commercial and institutional installations, such as ofce buildings, shopping centers, schools, and hospitals, lighting loads are often 50% or more of the total load. In addition, a feeder outage on rst ground fault is seldom crucial even in hospitals, which have emergency power in critical areas. For these reasons, a solidly grounded wye distribution, with the neutral used for lighting circuits, is usually the most economical, effective, and convenient design. In some instances it is an NEC requirement. In industrial installations, the effect of a shutdown caused by a single ground fault could be disastrous. An interrupted process could cause the loss of all the materials involved, often ruin the process equipment itself, and sometimes create extremely dangerous situations for operating personnel. On the other hand, lighting is usually only a small fraction of the total industrial electrical load. A solidly grounded neutral circuit conductor is not imperative and, when required, can be obtained from inexpensive lighting transformers. Because of the ability to continue in operation with one ground fault on the system, many existing industrial plants use ungrounded delta distribution. Today, new installations can have all the advantages of service continuity of the ungrounded delta, yet minimize the problems of the system, such as the difculty of locating the rst ground fault, risk of damage from a second ground fault, and damage transient overvoltages. A high-resistance grounded wye distribution can continue in operation with a ground fault on the system, will not develop transient overvoltages, and, because the ground point is established, locating a ground fault is less difcult than on an ungrounded system especially when a pulsing contactor design is applied. When combined with sensitive ground-fault protection, damage
CA08104001E

Phase A Phase B Phase C

N
Ungrounded Wye

Phase A Phase B Phase C

Figure 1.4-3. Ungrounded Systems Resistance-grounded systems (Figure 1.4-4) are simplest with a wye connection, grounding the neutral point directly through the resistor. Delta systems can be grounded by means of a zig-zag or other grounding transformer. Wye broken delta transformer banks may also be used.
Phase A Phase B Phase C

N R

Resistance-Grounded Wye

Phase A

Phase B Phase C

13 14 15 16 17 18 19 20 21
Delta With Derived Neutral ResistanceGrounded Using Zig-Zag Transformer

Figure 1.4-4. Resistance-Grounded Systems This derives a neutral point, which can be either solidly or impedancegrounded. If the grounding transformer has sufcient capacity, the neutral created can be solidly grounded and used as part of a 3-phase, 4-wire system. Most transformer-supplied systems are either solidly grounded or resistance grounded. Generator neutrals are often grounded through a reactor, to limit ground fault (zero sequence) currents to values the generator can withstand.

June 2006
Sheet 0085

TOC

Index

Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection
this makes ground fault protection mandatory on 480Y/277-volt services, but not on 208Y/120-volt services. On a 208-volt system, the voltage to ground is 120 volts. If a ground fault occurs, the arc goes out at current zero, and the voltage to ground is often too low to cause it to restrike. Therefore, arcing ground faults on 208-volt systems tend to be self-extinguishing. On a 480-volt system, with 277 volts to ground, restrike usually takes place after current zero, and the arc tends to be self-sustaining, causing severe and increasing damage, until the fault is cleared by a protective device. The NEC requires ground fault protection on the service disconnecting means. This protection works so fast that for ground faults on feeders, or even branch circuits, it will often open the service disconnect before the feeder or branch circuit overcurrent device can operate. This is highly undesirable, and in the NEC (230-95) a Fine Print Note (FPN) states that additional ground fault protective equipment will be needed on feeders and branch circuits where maximum continuity of electric service is necessary. Unless it is acceptable to disconnect the entire service on a ground fault almost anywhere in the system, such additional stages of ground fault protection must be provided. At least two stages of protection are mandatory in health care facilities (NEC Sec. 517-17). Overcurrent protection is designed to protect conductors and equipment against currents that exceed their ampacity or rating under prescribed time values. An overcurrent can result from an overload, short circuit or (high level) ground fault condition. When currents ow outside the normal current path to ground, supplementary ground fault protection equipment will be required to sense low-level ground fault currents and initiate the protection required. Normal phase overcurrent protection devices provide no protection against low-level ground faults. There are three basic means of sensing ground faults. The most simple and direct method is the ground return method as illustrated in Figure 1.4-5. This sensing method is based on the fact that all currents supplied by a transformer must return to that transformer.

1.4-11

Master TOC

from a second ground fault can be nearly eliminated. Ungrounded delta systems can be converted to highresistance grounded systems, using a zig-zag or other grounding transformer to derive a neutral, with similar benets, see Section 38. While the majority of manufacturing plants use solidly grounded systems, in many instances, the high-resistance grounded distribution will be the most advantageous.

Main

i
Neutral

Service Transformer Sensor GFR Ground Bus Main Bonding Jumper Grounding Electrode Conductor Equipment Grounding Conductor Typical 4W Load Typical Feeder

ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Ground Fault Protection

A ground fault normally occurs in one of two ways: By accidental contact of an energized conductor with normally grounded metal, or as a result of an insulation failure of an energized conductor. When an insulation failure occurs, the energized conductor contacts normally noncurrent-carrying grounded metal, which is bonded to or part of the equipment grounding conductor. In a solidly grounded system, the fault current returns to the source primarily along the equipment grounding conductors, with a small part using parallel paths such as building steel or piping. If the ground return impedance were as low as that of the circuit conductors, ground fault currents would be high, and the normal phase overcurrent protection would clear them with little damage. Unfortunately, the impedance of the ground return path is usually higher, the fault itself is usually arcing and the impedance of the arc further reduces the fault current. In a 480Y/277-volt system, the voltage drop across the arc can be from 70 to 140 V. The resulting ground fault current is rarely enough to cause the phase overcurrent protection device to open instantaneously and prevent damage. Sometimes, the ground fault is below the trip setting of the protective device and it does not trip at all until the fault escalates and extensive damage is done. For these reasons, low level ground protection devices with minimum time delay settings are required to rapidly clear ground faults. This is emphasized by the NEC requirement that a ground fault relay on a service shall have a maximum delay of one second for faults of 3000 amperes or more. The NEC (Sec. 230-95) requires that ground fault protection, set at no more than 1200 amperes, be provided for each service disconnecting means rated 1000 amperes or more on solidly grounded wye services of more than 150 volts to ground, but not exceeding 600 volts phase-to-phase. Practically,

Figure 1.4-5. Ground Return Sensing Method When an energized conductor faults to grounded metal, the fault current returns along the ground return path to the neutral of the source transformer. This path includes the main bonding jumper as shown in Figure 1.4-5. A current sensor on this conductor (which can be a conventional bar-type or window type CT) will respond to ground fault currents only. Normal neutral currents resulting from unbalanced loads will return along the neutral conductor and will not be detected by the ground return sensor.

This is an inexpensive method of sensing ground faults where protection per NEC (230-95) is desired. For it to operate properly, the neutral must be grounded in only one place as indicated in Figure 1.4-5. In many installations, the servicing utility grounds the neutral at the transformer and additional grounding is required in the service equipment per NEC (250-24(a)(2)). In such cases, and others including multiple source with multiple, interconnected neutral ground points, residual or zero sequence ground sensing methods should be employed.
A second method of detecting ground faults involves the use of a zero sequence sensing method, as illustrated in Figure 1.4-6. This sensing method requires a single, speciallydesigned sensor either of a toroidal or rectangular shaped conguration. This core balance current transformer surrounds all the phase and neutral conductors in a typical 3-phase, 4-wire distribution system. The sensing method is based on the fact that the vectorial sum of the phase and neutral currents in any distribution circuit will equal zero unless a ground fault condition exists downstream from the sensor. All currents that ow only in the circuit conductors, including balanced or unbalanced phase-to-phase and phaseto-neutral normal or fault currents, and harmonic currents, will result in zero

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-12 Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection
sensor output. However, should any conductor become grounded, the fault current will return along the ground path not the normal circuit conductors and the sensor will have an unbalanced magnetic ux condition and a sensor output will be generated to actuate the ground fault relay.
Zero Sequence Sensor Main Alternate Sensor Location

TOC

Index

June 2006
Sheet 0086

Master TOC

i ii 1 2 3

neutral. In a residual sensing scheme, the relationship of the polarity markings as noted by the X on each sensor is critical. Since the vectorial sum of the currents in all the conductors will total zero under normal, nonground faulted conditions, it is imperative that proper polarity connections are employed to reect this condition.
Sensor Polarity Marks Main

or in multi-tier schemes where additional levels of ground fault protection are desired for added service continuity. Additional grounding points may be employed upstream of the residual sensors but, not on the load side. Both the zero sequence and residual sensing methods have been commonly referred to as vectorial summation methods. Most distribution systems can utilize either of the three sensing methods exclusively or a combination of the sensing methods depending upon the complexity of the system and the degree of service continuity and selective coordination desired. Different methods will be required depending upon the number of supply sources and the number and location of system grounding points. As an example, one of the more frequently used systems where continuity of service to critical loads is a factor is the dual source system illustrated in Figure 1.4-8. This system utilizes tie-point grounding as permitted under NEC Sec. 250-24(a)(3). The use of this grounding method is limited to services that are dual fed (double-ended) in a common enclosure or grouped together in separate enclosures and employing a secondary tie. This scheme utilizes individual sensors connected in ground return fashion. Under tie breaker closed operating conditions either the M1 sensor or M2 sensor could see neutral unbalance currents and possibly initiate an improper tripping operation. However, with the polarity arrangements of these two sensors along with the tie breaker auxiliary switch (T/a) and interconnections as shown, this possibility is

Residual Sensors

Neutral

4
GFR

Neutral

Typical Feeder
GFR

5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
Typical 4W Load

Typical Feeder

Typical 4W Load

Figure 1.4-6. Zero Sequence Sensing Method Zero sequence sensors are available with various window openings for circuits with small or large conductors, and even with large rectangular windows to t over bus bars or multiple large size conductors in parallel. Some sensors have split cores for installation over existing conductors without disturbing the connections. This method of sensing ground faults can be employed on the main disconnect where protection per NEC (230-95) is desired. It can also be easily employed in multi-tier systems where additional levels of ground fault protection are desired for added service continuity. Additional grounding points may be employed upstream of the sensor but, not on the load side. Ground fault protection employing ground return or zero sequence sensing methods can be accomplished by the use of separate ground fault relays (GFRs) and disconnects equipped with standard shunt trip devices or by circuit breakers with integral ground fault protection with external connections arranged for these modes of sensing. In some cases, a reliable source of control power is needed. The third basic method of detecting ground faults involves the use of multiple current sensors connected in a residual sensing method as illustrated in Figure 1.4-7. This is a very common sensing method used with circuit breakers equipped with electronic trip units, current sensors and integral ground fault protection. The 3-phase sensors are required for normal phase overcurrent protection. Ground fault sensing is obtained with the addition of an identically rated sensor mounted on the

Figure 1.4-7. Residual Sensing Method As with the zero sequence sensing method, the resultant residual sensor output to the ground fault relay or integral ground fault tripping circuit will be zero if all currents ow only in the circuit conductors. Should a ground fault occur, the current from the faulted conductor will return along the ground path, rather than on the other circuit conductors, and the residual sum of the sensor outputs will not be zero. When the level of ground fault current exceeds the pre-set current and time delay settings, a ground fault tripping action will be initiated. This method of sensing ground faults can be economically applied on main service disconnects where circuit breakers with integral ground fault protection are provided. It can be used in protection schemes per NEC (230-95)

Power Transformer

Power Transformer

Main Bkr. 52-1

Neutral Sensor Main Bkr. 52-1

Tie Bkr. 52-T

Neutral Sensor Main Bkr. 52-2

Main Bkr. 52-2

A, B, C Neutral

A, B, C Neutral
Neutral Sensor Tie Bkr. 52-T

M1N M1G

4-Wire Load B4 B5 Digitrip

B5 B4 Digitrip Main Bkr. 52-1

3352-T B4 B5 Digitrip Main Bkr. 52-2

M2G M2N

TG

TN

Typical 4-Wire Feeder

( )B5 ( )B4

52-T a

Typical 52-T 4-Wire Feeder a

( )B5 ( )B4

B4 B5 Digitrip Main Bkr. 52-2

4-Wire Load
B4 B5 Digitrip

Figure 1.4-8. Dual Source System Single Point Grounding

For more information visit: www.EatonElectrical.com CA08104001E

June 2006
Sheet 0087

TOC

Index

Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection
types may be employed to accomplish the desired end results. Since the NEC (230-95) limits the maximum setting of the ground fault protection used on service equipment to 1200 A (and timed tripping at 3000 A for one second), to prevent tripping of the main service disconnect on a feeder ground fault, ground fault protection must be provided on all the feeders. To maintain maximum service continuity, more than two levels (zones) of ground fault protection will be required, so that ground fault outages can be localized and service interruption minimized. To obtain selectivity between different levels of ground fault relays, time delay settings should be employed with the GFR furthest downstream having the minimum time delay. This will allow the GFR nearest the fault to operate rst. With several levels of protection, this will reduce the level of protection for faults within the upstream GFR zones. Zone interlocking was developed for GFRs to overcome this problem. GFRs (or circuit breakers with integral ground fault protection) with zone interlocking are coordinated in a system to operate in a time delayed mode for ground faults occurring most remote from the source. However, this time delayed mode is only actuated when the GFR next upstream from the fault sends a restraining signal to the upstream GFRs. The absence of a restraining signal from a downstream GFR is an indication that any occurring ground fault is within the zone of the
Power Transformer

1.4-13

Master TOC

eliminated. Selective ground fault tripping coordination between the tie breaker and the two main circuit breakers is achieved by pre-set current pickup and time delay settings between devices GFR/1, GFR/2 and GFR/T. The advantages of increased service continuity offered by this system can only be effectively utilized if additional levels of ground fault protection are added on each downstream feeder. Some users prefer individual grounding of the transformer neutrals. In such cases a partial differential ground fault scheme should be used for the mains and tie breaker. An example of a residual partial differential scheme is shown in Figure 1.4-9. The scheme typically relies upon the vector sum of at least two neutral sensors in combination with each breakers 3-phase sensors. To reduce the complexity of the drawing, each of the breakers 3-phase sensors have not been shown. It is absolutely critical that the sensors polarities are supplied as shown, the neutral sensor ratings of the mains and tie are the same, and that there are no other grounds on the neutral bus made downstream of points shown. An innite number of ground fault protection schemes can be developed depending upon the number of alternate sources, the number of grounding points and system interconnections involved. Depending upon the individual system conguration, either mode of sensing or a combination of all

GFR next upstream from the fault and that device will operate instantaneously to clear the fault with minimum damage and maximum service continuity. This operating mode permits all GFRs to operate instantaneously for a fault within their zone and still provide complete selectivity between zones. The National Electrical Manufacturers Association (NEMA) states, in their application guide for ground fault protection, that zone interlocking is necessary to minimize damage from ground faults. A 2-wire connection is required to carry the restraining signal from the GFRs in one zone to the GFRs in the next zone. Circuit breakers with integral ground fault protection and standard circuit breakers with shunt trips activated by the ground fault relay are ideal for ground fault protection. Many fused switches over 1200 A, and CutlerHammer Type FDP fusible switches in ratings from 400 A to 1200 A, are listed by UL as suitable for ground fault protection. Fusible switches so listed must be equipped with a shunt trip, and be able to open safely on faults up to 12 times their rating. Power distribution systems differ widely from each other, depending upon the requirements of each user, and total system overcurrent protection, including ground fault currents, must be individually designed to meet these needs. Experienced and knowledgeable engineers must consider the power sources (utility or on-site), the effects of outages and costs of downtime, safety for people and equipment, initial and lifecycle costs, and many other factors. They must apply protective devices, analyzing the time-current characteristics, fault interrupting capacity, and selectivity and coordination methods to provide the most safe and cost-effective distribution system.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Power Transformer

Main Breaker 52-1

Neutral Sensor Main Breaker 52-1

X Neutral Sensor Main Breaker 52-2

Main Breaker 52-2

Further Information
s

Phase A, Phase B, Phase C Neutral Trip Unit

Tie Breaker 52-T

X

Phase A, Phase B, Phase C Neutral Trip Unit

Neutral Sensor X Tie Breaker 52-T

X X

Typical 4-Wire Feeder

52-1 a

52-T a

52-2 a

Typical 4-Wire Feeder

X X

s s 4-Wire Load

4-Wire Load Trip Unit Main Breaker 52-1 Trip Unit Trip Unit Tie Breaker Main Breaker 52-T 52-2

PRSC-4E System Neutral Grounding and Ground Fault Protection (ABB Publication). PB 2.2 NEMA Application Guide for Ground Fault Protective Devices for Equipment. IEEE Standard 142 Grounding of Industrial and Commercial Power Systems (Green Book). IEEE Emerald Book (Standard 1100). UL 96A, Installation Requirements for Lightning Protection Systems.

Figure 1.4-9. Dual Source System Multiple Point Grounding

CA08104001E For more information visit: www.EatonElectrical.com

1.4-14 Power Distribution Systems System Application Considerations

Grounding/Ground Fault Protection

TOC

Index

June 2006
Sheet 0088

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Lightning and Surge Protection

Physical protection of buildings from direct damage from lightning is beyond the scope of this section. Requirements will vary with geographic location, building type and environment, and many other factors (see IEEE/ANSI Standard 142, Grounding of Industrial and Commercial Power Systems). Any lightning protection system must be grounded, and the lightning protection ground must be bonded to the electrical equipment grounding system.

The electrical distribution system and equipment ground must be connected to this grounding electrode system by a grounding electrode conductor. All other grounding electrodes, such as those for the lightning protection system, the telephone system, television antenna and cable TV system grounds, and computer systems, must be bonded to this grounding electrode system.

Medium Voltage Equipment Surge Protection Considerations

Transformers
If the voltage withstand/BIL rating of the transformer is less than that of the switchgear feeding the transformer, surge protection is recommended at the transformer terminals, in line with established practices. In addition, consideration should be given to utilizing surge arresters and/or surge capacitors for transformers having equal or greater withstand/BIL ratings than that of the switchgear feeding the transformer for distribution systems where reected voltage waves and/or resonant conditions may occur. Typically incoming voltage surges are reected at the transformer primary terminals (because of the change in impedance) resulting in voltages at the ends of the transformer primary terminals/windings of up to two (2) times the incoming voltage wave. System capacitance and inductance values combined with the transformer impedance values can cause resonant conditions resulting in amplied reected waves. Surge arresters/capacitors when required, should be located as close to the transformer primary terminals as practical.

Grounding Electrodes
At some point, the equipment and system grounds must be connected to the earth by means of a grounding electrode system. Outdoor substations usually use a ground grid, consisting of a number of ground rods driven into the earth and bonded together by buried copper conductors. The required grounding electrode system for a building is spelled out in the NEC Article 250. The preferred grounding electrode is a metal underground water pipe in direct contact with the earth for at least 10 feet (3 m). However, because underground water piping is often plastic outside the building, or may later be replaced by plastic piping, the NEC requires this electrode to be supplemented by and bonded to at least one other grounding electrode, such as the effectively grounded metal frame of the building, a concrete-encased electrode, a copper conductor ground ring encircling the building, or a made electrode such as one or more driven ground rods or a buried plate. Where any of these electrodes are present, they must be bonded together into one grounding electrode system. One of the most effective grounding electrodes is the concrete-encased electrode, sometimes called the Ufer ground, named after the man who developed it. It consists of at least 20 feet (6 m) of steel reinforcing bars or rods not less than 1/2 inches (12.7 mm) in diameter, or at least 20 feet (6 m) of bare copper conductor, size No. 4 AWG or larger, encased in at least 2 inches (50.8 mm) of concrete. It must be located within and near the bottom of a concrete foundation or footing that is in direct contact with the earth. Tests have shown this electrode to provide a low-resistance earth ground even in poor soil conditions.

Motors
Surge capacitors and, where appropriate, surge arresters should be applied at the motor terminals.

Generators
Surge capacitors and station class surge arresters at the machine terminals.

Further Information
IEEE/ANSI Standard 142 Grounding Industrial and Commercial Power Systems (Green Book). s IEEE Standard 241 Electric Power Systems in Commercial Buildings (Gray Book). s IEEE Standard 141 Electric Power Distribution for Industrial Plants (Red Book).
s

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0089

TOC

Index

Power Distribution Systems System Application Considerations

Power Quality Dening the Problem
Power quality problems can be resolved in three ways: by reducing the variations in the power supply (power disturbances), by improving the load equipments tolerance to those variations, or by inserting some interface equipment (known as power conditioning equipment) between the electrical supply and the sensitive load(s) to improve the compatibility of the two. Practicality and cost usually determine the extent to which each option is used. Many methods are used to dene power quality problems. For example, one option is a thorough on-site investigation which includes inspecting wiring and grounding for errors, monitoring the power supply for power disturbances, investigating equipment sensitivity to power disturbances, and determining the load disruption and consequential effects (costs), if any. In this way, the power quality problem can be dened, alternative solutions developed, and optimal solution chosen. Before applying power-conditioning equipment to solve power quality problems, the site should be checked for wiring and grounding problems. Sometimes, correcting a relatively inexpensive wiring error, such as a loose connection or a reversed neutral and ground wire, can avoid a more expensive power conditioning solution.

1.4-15

Master TOC

Power Quality Terms Technical Overview

Introduction
Sensitive electronic loads deployed today by users require strict requirements for the quality of power delivered to loads. For electronic equipment, power disturbances are dened in terms of amplitude and duration by the electronic equipment operating envelope. Electronic loads may be damaged and disrupted, with shortened life expectancy, by disturbances. The proliferation of computers, variable frequency motor drives, UPS systems and other electronically controlled equipment is placing a greater demand on power producers for a disturbancefree source of power. Not only do these types of equipment require quality power for proper operation; many times, these types of equipment are also the sources of power disturbances that corrupt the quality of power in a given facility. Power Quality is dened according to IEEE Standard 1100 as the concept of powering and grounding electronic equipment in a manner that is suitable to the operation of that equipment. IEEE Standard 1159 notes that within the industry, alternate denitions or interpretations of power quality have been used, reecting different points of view. In addressing power quality problems at an existing site, or in the design stages of a new building, engineers need to specify different services or mitigating technologies. The lowest cost and highest value solution is to selectively apply a combination of different products and services as follows: Key Services/Technologies in the Power Quality Industry:
s s s s s s s s

Another option is to buy power conditioning equipment to correct any and all perceived power quality problems without any on-site investigation.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Power Quality Terms

Power Disturbance: Any deviation from the nominal value (or from some selected thresholds based on load tolerance) of the input ac power characteristics. Total Harmonic Distortion or Distortion Factor: The ratio of the root-meansquare of the harmonic content to the root-mean-square of the fundamental quantity, expressed as a percentage of the fundamental. Crest Factor: Ratio between the peak value (crest) and rms value of a periodic waveform. Apparent (Total) Power Factor: The ratio of the total power input in watts to the total volt-ampere input. Sag: An rms reduction in the ac voltage, at the power frequency, for the duration from a half-cycle to a few seconds. An undervoltage would have a duration greater than several seconds. Interruption: The complete loss of voltage for a time period. Transient: A sub-cycle disturbance in the ac waveform that is evidenced by a sharp brief discontinuity of the waveform. May be of either polarity and may be additive to or subtractive from the nominal waveform. Surge or Impulse: See transient. Noise: Unwanted electrical signals that produce undesirable effects in the circuits of control systems in which they occur. Common-Mode Noise: The noise voltage that appears equally and in phase from each current-carrying conductor to ground. Normal-Mode Noise: Noise signals measurable between or among active circuit conductors feeding the subject load, but not between the equipment grounding conductor or associated signal reference structure and the active circuit conductors.

Power quality surveys, analysis and studies. Power monitoring. Grounding products and services. Surge protection. Voltage regulation. Harmonic solutions. Lightning protection (ground rods, hardware, etc.). Uninterruptible Power Supply (UPS) or Motor-Generator (M-G) set.

Sometimes this approach is not practical because of limitations in time; expense is not justied for smaller installations; monitoring for power disturbances may be needed over an extended period of time to capture infrequent disturbances; the exact sensitivities of the load equipment may be unknown and difcult to determine; and nally, the investigative approach tends to solve only observed problems. Thus unobserved or potential problems may not be considered in the solution. For instance, when planning a new facility, there is no site to investigate. Therefore, power quality solutions are often implemented to solve potential or perceived problems on a preventive basis instead of a thorough on-site investigation.

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-16 Power Distribution Systems System Application Considerations

Power Quality Methodology for Ensuring Effective Power Quality to Electronic Loads
The Power Quality Pyramid is an effective guide for addressing power quality problems at an existing facility. The framework is also effective for specifying engineers who are designing a new facility. Power quality starts with grounding (the base of the pyramid) and then moves upward to address the potential issues. This simple, yet proven methodology, will provide the most cost-effective approach. As we move higher up the pyramid, the cost per kVA of mitigating potential problems increase and the quality of the power increases (Refer to Figure 1.4-10). The proliferation of communication and computer network systems has increased the need for proper grounding and wiring of ac and data/ communication lines. In addition to reviewing ac grounding and bonding practices, it is necessary to prevent ground loops from affecting the signal reference point.

TOC

Index

June 2006
Sheet 0090

Master TOC

i ii 1 2 3 4 5

The benet of implementing cascaded network protection is shown in Figure 1.4-11. Combined, the two stages of protection at the service entrance and branch panel locations reduce the IEEE 62.41 recommended test wave (C3 20 kV, 10 kA) to less than 200 V voltage, a harmless disturbance level for 120 V rated sensitive loads. If only building entrance feeder protection were provided, the let-through voltage will be approximately 950 V in a 277/480 V system exposed to induced lightning surges. This level of let-through voltage can cause degradation or physical damage of most electronic loads. Wherever possible, consultants, speciers and application engineers should ensure similar loads are fed from the same source. In this way, disturbancegenerating loads are separated from electronic circuits affected by power disturbances. For example; motor loads, HVAC systems and other linear loads should be separated from the sensitive process control and computer systems. The most effective and economic solution for protecting a large number of loads is to install parallel SPDs at the building service entrance feeder and panelboard locations. This reduces the cost of protection for multiple sensitive loads.

2. Surge Protection
Surge Protection Devices (SPDs) are recommended as the next stage power quality solutions. NFPA, UL 96A, IEEE Emerald Book and equipment manufacturers recommend the use of surge protectors. The transient voltage surge suppressors (also called TVSS) shunt short duration voltage disturbances to ground, thereby preventing the surge from affecting electronic loads. When installed as part of the facility-wide design, SPDs are cost-effective compared to all other solutions (on a $/kVA basis). The IEEE Emerald book recommends the use of a two-stage protection concept. For large surge currents, diversion is best accomplished in two stages: the rst diversion should be performed at the service entrance to the building. Then, any residual voltage resulting from the action can be dealt with by a second protective device at the power panel of the computer room (or other critical loads).

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Cost Per kVA 5. Uninterruptible Power Supply (UPS, Gen. Sets, etc.) 4. Harmonic Distortion 3. Voltage Regulation 2. Surge Protection 1. Grounding

Figure 1.4-10. Power Quality Pyramid

TVSS

1. Grounding
480 V 120/208 V

CP

TVSS

20,000 V

Input - high energy transient disturbance; IEEE Category C3 Impulse 20,000 V; 10,000 A

Grounding represents the foundation of a reliable power distribution system. Grounding and wiring problems can be the cause of up to 80% of all power quality problems. All other forms of power quality solutions are dependent upon good grounding procedures.

PEAK VOLTAGE

Stage 1 Protection (Service Entrance)

Computer or Sensitive Loads

Stage 2 Protection (Branch Location)

Best achievable performance with single TVSS at main panel (950 V, at Stage 1)
800 V 400 V 0

System Test Parameters: IEEE C62.41[10] and C62.45 [10] test procedures using category; 480 V main entrance panels; 100 feet (30 m) of 3-phase wire; 480/208 V distribution transformer; and 208 V branch panel.
= SPD or TVSS

25 uS 50 uS TIME (MICROSECONDS)

Two stage (cascade approach) achieves best possible protection (less than 200 V at Stage 2)

Figure 1.4-11. Cascaded Network Protection

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0091

TOC

Index

Power Distribution Systems System Application Considerations

Power Quality
Building entrance SPDs protect the facility against large external transients, including lightning. s SPDs are bi-directional and prevent transient and noise disturbances from feeding back within a system when installed at distribution or branch panels. s Two levels of protection safeguard sensitive loads from physical damage or operational upset.
s

1.4-17

Master TOC

The recommended system approach for installing SPDs is summarized in Figure 1.4-12.
1. Identify Critical Loads 2. Identify Non-Critical Loads 3. Identify Noise and Disturbance Generating Loads 4. Review Internal Power Distribution Layout 5. Identify Facility Exposure to Expected Levels of Disturbance 6. Apply Mitigating Equipment to: a) Service Entrance Main Panels b) Key Sub-Panels c) Critical Loads d) Data and Communication Lines

tion wires, the area between wires is reduced and the mutual inductance affect minimized.

i ii 1 2 3 4 5 6 7 8 9 10 11 12

Side Mounted SPD vs. Integral SPD

Directly connecting the surge suppresser to the bus bar of electrical distribution equipment results in the best possible level of protection. Compared to side mounted devices, connecting the SPD unit to the bus bar eliminates the need for lead wires and reduces the let-through voltage up to 50% (see Figure 1.4-13). Given that surges are high frequency disturbances, the inductance of the installation wiring increases the let-through voltage of the protective device. Figure 1.4-14 shows that for every inch of lead length, the let-through voltage is increased by an additional 15 to 25 V above the manufacturers stated suppression performance. Lead length has the greatest effect on the actual level of protection realized. Twisting of the installation wires is the second most important installation consideration. By twisting the installa-

Increasing the diameter of the installation wires is of negligible benet. Inductance is a skin effect phenomenon and a function of wire circumference. Since only a marginal reduction in inductance is achieved when the diameter of the installation conductors is increased, the use of large diameter wire results in only minimal improvement (see Figure 1.4-14).
Further benets provided by integrated surge suppression designs are the elimination of eld installation costs and the amount of expensive outboard wall space taken up by side mounted SPD devices.

Building Entrance Feeder Installation Considerations

Installing a SPD device immediately after the switchgear or switchboard main breaker is the optimal location for protecting against external disturbances such as lightning. When placed in this location, the disturbance is intercepted by the SPD and reduced to a minimum before reaching the distribution and/or branch panel(s). The use of a disconnect breaker eliminates the need to de-energize the building entrance feeder equipment should the SPD fail or require isolation for Megger testing.

Figure 1.4-12. System Approach for Installing SPDs

There may be specic critical loads within a facility that require a higher level of protection. A series SPD is best suited for protecting such loads.

Advantages of the System Approach are:

s

The lowest possible investment in mitigating equipment to protect a facility.

208Y/120 Panelboard (integrated versus side mounted SPD) 1000 Let-Through Voltage at Bus Bar Side Mounted SPD used for Retrofit Applications SPD Integrated into Panelboards, Switchboards, MCCs 800 600 400 200 0 -200 -2.00 Surge Event 0.00 2.00 4.00 6.00 8.00 10.00 Integrated SPD (direct bus bar connection) Side Mounted SPD Device (assuming 14-inch (355.6 mm) lead length to bus)

13 14 15 16 17 18 19

SPD SPD

GRO UND

G RO UND

G N

Microseconds

Figure 1.4-13. Performance Comparison of Side Mounted vs. Integrated SPD

20 21
CA08104001E For more information visit: www.EatonElectrical.com

1.4-18 Power Distribution Systems System Application Considerations

Power Quality

TOC

Index

June 2006
Sheet 0092

Master TOC

Additional Let-Through Voltage

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Additional Let-Through Voltage Using IEEE C1(6000V, 3000A)[3] Waveform (UL 1449 Test Wave)[12]
900 800 700 600 500 400 300 200 100 0

Reference Section 36 for detailed information on SPDs.

14 AWG 10 AWG 4 AWG

209V (23%) 673V (75%)

3. Voltage Regulation
Voltage Regulation (i.e., sags or overvoltage) disturbances are generally site- or load-dependent. A variety of mitigating solutions are available depending upon the load sensitivity, fault duration/magnitude and the specic problems encountered. It is recommended to install monitoring equipment on the ac power lines to assess the degree and frequency of occurrences of voltage regulation problems. The captured data will allow for the proper solution selection.

3 Feet (914.4 mm) Lead Length Loose Wiring Twisted Wires

1 Foot (304.8 mm) Lead Length, Twisted Wires

Figure 1.4-14. The Effect of Installation Lead Length on Let-Through Voltage

Additional to UL 1449 ratings.

The size or capacity of a suppressor is measured in surge current per phase. Larger suppressors rated at approximately 250 kA per phase should be installed at the service entrance to survive high-energy surges associated with lightning. A 250 kA per phase surge rating allows for over a 25 year life expectancy assuming an IEEE dened high exposure environment. Lower surge rating devices may be utilized; however, device reliability and long-term performance may be compromised. For aerial structures, the 99.8 percentile recorded lightning stroke current is less than 220 kA. The magnitude of surges conducted or induced into a facility electrical distribution system is considerably lower given the presence of multiple paths for the surge to travel along. It is for this reason that IEEE C62.41 recommends the C3 (20 kV, 10 kA) test wave for testing SPDs installed at building entrance feeders. SPDs with surge ratings greater than 250 kA are not required, however, higher ratings are available and may provide longer life.

switch is about 50 to 60 V. This increase in disturbance voltage can result in process disruption and downtime.

4. Harmonics Distortion
Harmonics and Nonlinear Loads
Until recently, most electrical loads were linear. Linear loads draw the full sine wave of electric current at its 60 cycle (Hz) fundamental frequency Figure 1.4-15 shows balance single-phase, linear loads. As the gure shows, little or no current ows in the neutral conductor when the loads are nonlinear and balanced. With the arrival of non-linear electronic loads, where the ac voltage is converted to a dc voltage, harmonics are created because of the use of only part of the ac sine wave. In this conversion from ac to dc, the electronics are turned on in the 60 cycle wave at a given point in time to obtain the required dc level. The utilization of only part of the sign wave causes harmonics. It is important to note that the current distortion caused by loads such as rectiers or switch mode power supplies causes the voltage distortion. That voltage distortion is caused by distorted currents owing through an impedance. The amount of voltage distortion depends on:
s s

Installing Dataline Surge Protection

Most facilities also have communication lines that are potential sources for external surges. As identied by the Power Quality Pyramid, proper grounding of communication lines is essential for dependable operation. NEC Article 800 states that all data, power and cable lines be grounded and bonded. Power disturbances such as lightning can elevate the ground potential between two communicating pieces of electronic equipment with different ground references. The result is current owing through the data cable causing component failure, terminal lock-up, data corruption and interference. NFPA 780 D 4.8 warns that surge suppression devices should be installed on all wiring entering or leaving electronic equipment, usually power, data or communication wiring. Surge suppressers should be installed at both ends of a data or communication cable. In those situations where one end of the cable is not connected into an electronic circuit (e.g., contactor coil), protection on the electronic end only is required. To prevent the coupling or inducing of power disturbances into communication lines, the following should be avoided: Data cables should not be run over uorescent lighting xtures. s Data cables should not be in the vicinity of electric motors. s The right category cable should be used to ensure transmission performance. s Data cables must be grounded at both ends when communicating between buildings.
s

Installing Panelboard Surge Protection Devices

Smaller surge capacity SPDs (120 kA per phase) are installed at branch panelboards where power disturbances are of lower energy but occur much more frequently. This level of surge current rating should result in a greater than 25 year life expectancy. When isolated ground systems are used, the SPD should be installed such that any common mode surges are shunted to the safety ground. The use of a disconnect breaker is optional. The additional let-through voltage resulting from the increased inductance caused by the disconnect

System impedance. Amount of distorted current.

Devices that can cause harmonic disturbances include rectiers, thrusters and switching power supplies, all of which are non-linear. Further, the proliferation of electronic equipment such as computers, UPS systems, variable speed drives, programmable logic controllers, and the like: non-linear loads have become a signicant part of many installations. Other types of harmonic-producing loads include arcing devices (arc furnaces, uorescent lights) and iron core storable devices (transformers, especially during energization).
CA08104001E

For more information visit: www.EatonElectrical.com

June 2006
Sheet 0093

TOC

Index

Power Distribution Systems System Application Considerations

Power Quality
present on the three phases add together in the neutral, as shown in Figure 1.4-16, rather than cancel each other out, as shown in Figure 1.4-15. Odd non-triplen harmonics are classied as positive sequence or negative sequence and are the 1st, 5th, 7th, 11th, 13th, etc. In general, as the order of a harmonic gets higher, its amplitude becomes smaller as a percentage of the fundamental frequency.

1.4-19

Master TOC

Non-linear load currents vary widely from a sinusoidal wave shape; often they are discontinuous pulses. This means that non-linear loads are extremely high in harmonic content. Triplen harmonics are the 3rd, 9th, 15th,...harmonics. Further, triplen harmonics are the most damaging to an electrical system because these harmonics on the A-phase, B-phase and C-phase are in sequence with each other. Meaning, the triplen harmonics

Harmonic Issues
Harmonic currents perform no work and result in wasted electrical energy that may over burden the distribution system. This electrical overloading may contribute to preventing an existing electrical distribution system from serving additional future loads. In general, harmonics present on a distribution system can have the following detrimental effects: 1. Overheating of transformers and rotating equipment.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

60 Hz Fundamental

2. Increased hysteresis losses. 3. Decreased kVA capacity. 4. Overloading of neutral. 5. Unacceptable neutral-to-ground voltages.

A Phase

120 Lagging

6. Distorted voltage and current waveforms.

B Phase

7. Failed capacitor banks. 8. Breakers and fuses tripping. 9. Double or ever triple sized neutrals to defy the negative effects of triplen harmonics.

120 Lagging

C Phase

Balance Neutral Current

Figure 1.4-15. Balanced Neutral Current Equals Zero

60 Hz Fundamental 3rd Harmonic A Phase

In transformers, generators and uninterruptible power supplies (UPS) systems, harmonics cause overheating and failure at loads below their ratings because the harmonic currents cause greater heating than standard 60 Hz current. This results from increased eddy current losses, hysteresis losses in the iron cores, and conductor skin effects of the windings. In addition, the harmonic currents acting on the impedance of the source cause harmonics in the source voltage, which is then applied to other loads such as motors, causing them to overheat. The harmonics also complicate the application of capacitors for power factor correction. If, at a given harmonic frequency, the capacitive impedance equals the system reactive impedance, the harmonic voltage and current can reach dangerous magnitudes. At the same time the harmonics create problems in the application of power factor correction capacitors, they lower the actual power factor. The rotating meters used by the utilities for watthour and various measurements do not detect the distortion component caused by the harmonics. Rectiers with diode front ends and large dc side capacitor banks have displacement power factor of 90% to 95%. More recent electronic meters are capable of metering the true kVA hours taken by the circuit. Single-phase power supplies for computer and xture ballasts are rich in third harmonics and their odd multiples.

120 Lagging

B Phase

120 Lagging

C Phase

Neutral Triplen Current

Figure 1.4-16. Unbalanced Single-Phase Loads with Triplen Harmonics

CA08104001E For more information visit: www.EatonElectrical.com

Phase Triplen Harmonics Added in the Neutral

1.4-20 Power Distribution Systems System Application Considerations

Power Quality
Even with the phase currents perfectly balanced, the harmonic currents in the neutral can total 173% of the phase current. This has resulted in overheated neutrals. The Information Technology Industry Council (ITIC) formerly known as CBEMA, recommends that neutrals in the supply to electronic equipment be oversized to at least 173% of the ampacity of the phase conductors to prevent problems. CBEMA also recommends derating transformers, loading them to no more than 50% to 70% of their nameplate kVA, based on a rule-of-thumb calculation, to compensate for harmonic heating effects. In spite of all the concerns they cause, non-linear loads will continue to increase. Therefore, the design of non-linear loads and the systems that supply them will have to be designed so that their adverse effects are greatly reduced. Table 1.4-3 shows the typical harmonic orders from a variety of harmonic generating sources. Table 1.4-3. Source and Typical Harmonics
Source 6 Pulse Rectier 12 Pulse Rectier 18 Pulse Rectier Switch-Mode Power Supply Fluorescent Lights Arcing Devices Transformer Energization Typical Harmonics 5, 7, 11, 13, 17, 19 11, 13, 23, 25 17, 19, 35, 37 3, 5, 7, 9, 11, 13 3, 5, 7, 9, 11, 13 2, 3, 4, 5, 7 2, 3, 4

TOC

Index

June 2006
Sheet 0094

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Total Harmonic Distortion

Revised standard IEEE 519-1992 indicates the limits of current distortion allowed at the PCC (Point of Common Coupling) point on the system where the current distortion is calculated, usually the point of connection to the utility or the main supply bus of the system. The standard also covers the harmonic limits of the supply voltage from the utility or cogenerators. Table 1.4-4. Low Voltage System Classication and Distortion Limits for 480 Volt Systems
Class Special Application General System Dedicated System C 10 5 2 AN 16,400 22,800 36,500 DF 3% 5% 10%

Table 1.4-6. Current Distortion Limits for General Distribution Systems (120 V Through 69000 V)
Maximum Harmonic Current Distortion in Percent of IL Individual Harmonic Order (Odd Harmonics) ISC /IL <11 11 17 23 35 TDD <h <h <h <h <17 <23 <35 2.0 3.5 4.5 5.5 7.0 1.5 2.5 4.0 5.0 6.0 .6 1.0 1.5 2.0 2.5 .3 .5 .7 1.0 1.4 5.0 8.0 12.0 15.0 20.0

<20 20<50 50<100 100<1000 >1000

4.0 7.0 10.0 12.0 15.0

All power generation equipment is limited to these values of current distortion, regardless of actual ISC/IL where: ISC = Maximum short circuit current at PCC. IL = Maximum demand load current (fundamental frequency component) at PCC.

Special systems are those where the rate of change of voltage of the notch might mistrigger an event. AN is a measurement of notch characteristics measured in voltmicroseconds, C is the impedance ratio of total impedance to impedance at common point in system. DF is distortion factor.

TDD = Total Demand Distortion. Even harmonics are limited to 25% of the odd harmonic limits above. Current distortions that result in a dc offset, e.g., half-wave converters, are not allowed.

Harmonic Solutions
In spite of all the concerns non-linear loads cause, these loads will continue to increase. Therefore, the design of non-linear loads and the systems that supply them will need design so adverse harmonic effects are greatly reduced. Table 1.4-7 and depicts many harmonic solutions along with their advantages and disadvantages.

Table 1.4-5. Utility or Cogenerator Supply Voltage Harmonic Limits

Voltage Range Maximum Individual Harmonic Total Harmonic Distortion 2.3-69 kV 69-138 kV >138 kV 3.0% 1.5% 1.0%

5.0%

2.5%

1.5%

Generally, magnitude decreases as harmonic order increases.

Vh Percentages are x 100 for each V1 harmonic and V thd =

h 1/2

= h max h = 2

2 V h

It is important for the system designer to know the harmonic content of the utilitys supply voltage because it will affect the harmonic distortion of the system.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0095

TOC

Index

Power Distribution Systems System Application Considerations

Power Quality

1.4-21

Master TOC

Table 1.4-7. Harmonic Solutions for Given Loads

Load Type Drives and Rectiers Includes 3-Phase UPS Loads Solutions Line Reactors Advantages
s Inexpensive. s For 6-pulse standard drive/rectier, can

Disadvantages
s May require additional compensation.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

reduce harmonic current distortion from 80% down to about 35 40%. K-Rated/Drive Isolation Transformer dc Choke 12-Pulse Convertor
s Offers series reactance (similar to line s No advantage over reactors for

reactors) and provides isolation for some transients.

s Slightly better than ac line reactors

reducing harmonics unless in pairs for shifting phases.

s Not always an option for drives. s Less protection for input semiconductors. s Cost difference approaches 18-pulse drive

for 5th and 7th harmonics.

s 85% reduction versus standard

6-pulse drives. Harmonic Mitigating Transformers/Phase Shifting

s Substantial (50% 80%) reduction in

and blocking lters, which guarantee IEEE 519 compliance.

s Harmonic cancellation highly dependent

harmonics when used in tandem.

on load balance.
s Must have even multiples of

matched loads. Tuned Filters

s Bus connected accommodates

load diversity. s Provides PF correction. Broadband Filters 18-Pulse Converter

s Makes 6-pulse into the equivalent

s Requires allocation analysis. s Sized only to the requirements of that system.

Must be resized if system changes.

s Higher cost. s Requires one lter per drive. s High cost.

of 18-pulse.
s Excellent harmonic control for drives

above 100 hp. s IEEE 519 compliant. Active Filters Computers/ Switch-Mode Power Supplies Neutral Blocking Filter
s Handles load/harmonic diversity. s Complete solution up to 50th harmonic. s Eliminates the 3rd harmonic from load. s Relieves system capacity. s Possible energy savings. s 3rd harmonic recalculated back to the load. s When used as phase-shifted transformers, s High cost. s High cost. s May increase voltage distortion. s Requires fully rated circuits and

Harmonic Mitigating Transformers

oversized neutrals to the loads.

reduces other harmonics. s Reduces voltage at-topping. Oversized Neutral/Derated Transformer K-Rated Transformer Fluorescent Lighting Harmonic Mitigating Transformers
s Tolerate harmonics rather than correct. s Typically least expensive. s Tolerate harmonics rather than correct. s 3rd harmonic recalculated back to the load. s When used as phase-shifted transformers, s Upstream and downstream equipment

fully rated for harmonics.

s Does not reduce system harmonics. s Requires fully rated circuits and

oversized neutrals to the loads.

reduces other harmonics.

s Reduces voltage at-topping.

K-Rated Transformer Low Distortion Ballasts Welding/Arcing Loads Active Filters

s Tolerate harmonics rather than correct them. s Does not reduce system harmonics. s Reduce harmonics at the source. s Fast response and broadband s Additional cost and typically more

expensive than system solutions.

s High cost.

harmonic correction.
s Reduces voltage icker.

Tuned Filters System Solutions Tuned Filters Harmonic Mitigating Transformers Active Filters

s SCR controlled tuned lters simulates

s SCR controlled units are high cost

an active lter response.

s Provides PF correction. s Lower cost compared to other systems. s Excellent choice for new design

but xed lters are reasonable.

s System analysis required to verify application.

Must be resized if system changes.

s No PF correction benet. s Highest cost.

or upgrade.
s Ideal solution and

handles system diversity.

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-22 Power Distribution Systems Uninterruptible Power Systems (UPS)

TOC

Index

June 2006
Sheet 0096

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

5. Uninterruptible Power Systems (UPS)

The advent of solid-state semiconductors over 40 years ago, and their subsequent evolution to transistors, and the miniaturization of electronics into microprocessor over 25 years ago, has created numerous computation machines that assist us in every conceivable manner. These machines, and their clever congurations, whether they take the form of computers, appliance controls, fax machines, phone systems, computers of all sizes, server systems and server farms, emergency call centers, data processing at banks, credit companies, private company communication networks, government institutions, and defense agencies all rely on a narrow range of nominal ac power in order for these devices to work properly. Indeed, many other types of equipment also require that the ac electrical power source be at or close to nominal voltage and frequency. Disturbances of the power translate into failed processes, lost data, decreased efciency and lost revenue.

The normal power source supplied by the local utility or provider is not stable enough over time to continuously serve these loads without interruption. It is possible that a facility outside a major metropolitan area served by the utility grid will experience outages of some nature 15 20 times in one year. Certain outages are caused by the weather, and others by the failure of the utility supply system due to equipment failures or construction interruptions. Some outages are only several cycles in duration, while others may be for hours at a time. In a broader sense, other problems exist in the area of power quality, and many of those issues also contribute to the failure of the supply to provide that narrow range of power to the sensitive loads mentioned above. Power Quality problems take the form of any of the following: power failure, power sag, power surge, undervoltage, overvoltage, line noise, frequency variations, switching transients, and harmonic distortion. Regardless of the reason for outages and power quality problems, the sensitive loads can not function normally without a backup power source and in many cases the loads must be isolated from the instabilities of the utility supply and power quality problems and given clean reliable power on a continuous basis, or be able to switch over to reliable clean electrical power quickly.

Uninterruptible Power Supply (UPS) systems have evolved to serve the needs of sensitive equipment and can supply a stable source of electrical power, or switch to backup to allow for an orderly shutdown of the loads without appreciable loss of data or process. In the early days of mainframe computers, motor-generator sets provide isolation and clean power to the computers. They did not have deep reserves, but provided extensive ride-through capability while other sources of power (usually standby emergency engine generator sets) were brought to bear to serve the motor-generator sets while the normal source of power was unstable or unavailable. UPS systems have evolved along the lines of rotary types and static types of systems, and they come in many congurations, and even hybrid designs having characteristics of both types. The discussion that follows attempts to compare and contrast the two types of UPS systems, and give basic guidance on selection criteria. This discussion will focus on the medium, large and very large UPS systems required by users who need more than 10 kVA of clean reliable power.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0097

TOC

Index

Power Distribution Systems Uninterruptible Power Systems (UPS)

1.4-23

Master TOC

Power Ratings of UPS Systems

Small UPS: Typically 300 VA to 10 kVA, and sometimes as high as 18 kVA s Medium UPS: 10 kVA to 60 kVA s Large UPS: 100 kVA to 200 kVA units, and higher when units are paralleled s Very Large UPS: 200 kVA to 750 kVA units, and higher when units are paralleled
s

Each of these categories is arbitrary because manufacturers have many different UPS offerings for the same application. The choice of UPS type and the conguration of UPS modules for a given application depends upon many factors, including how many Power Quality problems the UPS is expected to solve, how much future capacity is to be purchased now for future loads, the nature of the sensitive loads and load wiring, which type of UPS system is favored, rotary or static, choices of battery or dc storage technology considered, and a host of other application issues.

low rotational speeds. These legacy types of hybrid UPS systems are not the focus of this discussion, since only one or two vendors offer these hybrid types of rotary UPS systems, although admittedly they continue to be used in very large-scale data center applications. See Figure 1.4-17 for the modern high speed Rotary UPS systems discussed in this section of the guide. These types of modern Rotary UPS systems are advanced, integrated designs utilizing scalable congurations of high-speed ywheel, motor and generator in one compact UPS package. The new rotary technologies have the potential to replace battery backup systems, or at least reduce the battery content for certain applications. The appeal of rotary systems is the avoidance of the purchase, maintenance, and facility space required by dc battery based backup systems.

High Speed Rotary Concept of Operation

The modern Rotary type of UPS operation is understood by reviewing the four topics below: Startup Mode, Normal Operation Mode, Discharge Mode, and Recharge Mode.

system checks are performed then the input Contactor is closed. The Static Disconnect Switch is turned on and the conduction angle is rapidly increased from zero to an angle that causes the dc bus voltage between the Utility Converter and the Flywheel Converter to reach approximately 650 volts through the rectifying action of the freewheeling diodes in the Utility Converter. As soon as this level of dc voltage is reached the Static Disconnect turns on fully. The next steps involved the Utility Converter IGBTs to start ring which allows the converter to act as a Rectier, a regulating voltage source and an active harmonic lter. As the IGBTs begin to operate, the dc bus is increased to a normal operating voltage of approximately 800 volts, and the output bus is transferred from Bypass to the output of the power electronics module. The transfer from Bypass is completed when the Output Contactor is closed and the Bypass Contactor opened in a make-before-break manner. The ring of the SCRs in the Static Disconnect Switch is now changed so that each SCR in each phase is only turned on during the half-cycle, which permits real power to ow from the utility supply to the UPS. This ring pattern at the Static Disconnect Switch prevents power from the Flywheel from feeding backwards into the utility supply and assures that all of the Flywheel energy is available to support the Load.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Rotary UPS Systems

Typical Ratings
300 kVA 900 kVA/720 kW maximum

Startup Mode
The UPS output is energized on Bypass as soon as power is applied from the Source to the system input. The UPS continues the startup procedure automatically when the front panel controls are placed into the Online position. Internal UPS

Typical Rotary Congurations

Rotary UPS systems are among the oldest working systems developed to protect sensitive loads. Many of these systems are complicated enginegenerator sets coupled with high inertial ywheels operated at relatively

Static Bypass Option It = Input Current Ir = Real Load Current Ic = Charging Current Ig = Voltage Regulation Current Bypass Contactor It = Ir + Ic + Ig Source Flywheel Converter Ix Field Coil Driver ac dc Ih Integrated Motor/Flywheel/ and Generator dc ac Utility Converter Ic Inverter Fuse Ig Output Transformer Id = Output Current Ih = Harmonic Current Ix = Reactive Load Current Ir = Real Load Current Id = Ih + Ix + Ir Line Inductor Output Contactor Load

15 16 17 18 19 20 21

Input Contactor

Static Disconnect Switch

Filter Inductor

Figure 1.4-17. Typical High Speed Modern Rotary UPS

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-24 Power Distribution Systems Uninterruptible Power Systems (UPS)

TOC

Index

June 2006
Sheet 0098

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Immediately after the output is transferred from Bypass to the power electronic module, the Flywheel Field is excited which also provides magnetic lift to unload the Flywheel bearings. The Flywheel Inverter is turned on and gradually increases frequency at a constant rate to accelerate the Flywheel to approximately 60 RPM. Once the Flywheel reached 60 RPM, the Flywheel Inverter controls the acceleration to keep currents below the maximum charging and the maximum input settings. Once the Flywheel reaches 4000 RPM, the UPS is fully functional and capable of supporting the Load during a power quality event. Flywheel acceleration continues until the Flywheel reaches full charge at 7,700 RPM. The total time to complete startup is less than 5 minutes.

nominal output voltage, just enough reactive current ows through the line inductor to make up the difference between the input voltage and the output voltage. The Load current consists of three components: the harmonic current required by the load, the reactive load current, and the real current, which does the work. The Utility Converter supplies both the harmonic and reactive currents. Since these currents supply no net power to the load, the Flywheel supplies no energy for these currents. They circulate between the Utility Converter and the Load. The power stage controls analyze the harmonic current requirements of the load and set the ring angle of the inverter IGBTs to make the Utility Converter a very low impedance source to any harmonic currents. Thus, non-linear load currents are supplied almost entirely from the Utility Converter with little effect on the quality of the UPS output voltage waveform and with almost no transmission of load harmonics currents to the input of the UPS.

nominal levels. Recharging the Flywheel is accomplished by controlling the Utility and Flywheel Converter in a similar manner as is used to maintain full charge in the Normal Operation Mode, however the IGBT gating points are changed to increase current into the Flywheel.

High Speed Rotary Advantages

s s s s s s

Normal Operation Mode

Once the UPS is started and the Flywheel is operating at greater than 4,000 RPM, the UPS is in the Normal Operating Mode where it is regulating output voltage and supplying reactive and harmonic currents required by the Load. At the same time it cancels the effect of load current harmonics on the UPS output voltage. Input current consists of three components: real load current, charging current, and voltage regulation current. Real current is current that is in phase with the supply voltage and supplies real power to the Load. Real current owing through the line inductor causes a slight phase shift of the current lagging the voltage by 10 degrees and ensures that the UPS can quickly transfer to Bypass without causing unacceptable switching transients. The second component is charging current required by the Flywheel to keep the rotating mass fully charged at rated RPM, or to recharge the rotating mass after a discharge. The power to maintain full charge is low at 2 kW and is accomplished by the IGBTs of the Flywheel Converter gating to provide small pulses of motoring current to the Flywheel. This current can be much higher if fast recharge times are selected. The nal component of input current is the voltage regulation current, which is usually a reactive current that circulates between the input and the Utility Converter to regulate the output voltage. Leading reactive current causes a voltage boost across the line inductor, and a lagging current causes a bucking voltage. By controlling the Utility Converter to maintain

s s

Addresses all power quality problems. Battery systems are not required or used. No battery maintenance required. Unlimited discharge cycles. 150 second recharge time available. Wide range of operating temperatures can be accommodated (-20 to 40 degrees C). Small compact size and less oor space required (500 kW systems takes 20 sq.ft.). N+1 reliability available up to 900 kVA maximum. No disposal issues. Flywheel does not have deep reserve capacity rides through for up to 13 seconds at 100% load. Some enhanced ywheel systems may extend the ride through to 30 seconds at 100% load. Mechanical ywheel maintenance required every 2 3 years, and oil changes required every year. Recharge fast rates require the input to be sized for 125% of nominal current. Flywheels failures in eld not understood. Requires vacuum pumps for high speed ywheels. Limited number of vendors and experience.

High Speed Rotary Disadvantages

s

Discharge Mode
The UPS senses the deviation of the voltage or frequency beyond programmed tolerances and quickly disconnects the supply source by turning off the Static Disconnect Switch and opening the Input Contactor. The disconnect occurs in less than one-half cycle. Then the Utility Converter starts delivering power from the dc bus to the Load, and the Flywheel Converter changes the ring point of its IGBTs to deliver power to the dc bus. The UPS maintains a clean output voltage within 3% or nominal voltage to the Load when input power is lost.
s

s s s

Recharge Mode
When input power is restored to acceptable limits, the UPS synchronizes the output and input voltages, closes the Input Contactor and turns on the Static Disconnect Switch. The Utility Converter then transfers power from the Flywheel to the input source by linearly increasing the real input current. The transfer time is programmable from 1 to 15 seconds. As soon as the load power is completely transferred to the input source, the Utility Converter and Flywheel Converter start to recharge the Flywheel and return to Normal Operation Mode. The Flywheel recharge power is programmable between a slow and fast rate, and using the fast rate results in an increase of UPS input current over

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0099

TOC

Index

Power Distribution Systems Uninterruptible Power Systems (UPS)

1.4-25

Master TOC

Static UPS Systems

Typical Ratings
40 kVA 750 kVA/600 kW, and higher when multiple units are paralleled

2. The Rectier/Charger function converts the normal ac power to dc power to charge the Battery and power the Inverter. The Load is isolated from the normal input Source. 3. The Battery stores dc energy for use when input power to the UPS fails. The amount of power available from the dc Battery system and time to discharge voltage is a function of the type of Battery selected and the amperehour sized used. Battery systems should be sized for no less than 5 minutes of clean power usage from a fully charged state, and in many cases are sized to provide more time on Battery power. 4. The dc link connects the output of the Rectier/Charger to the input of the Inverter and to the Battery. Typically the Rectier/Charger is sized slightly higher than 100% of UPS output since it must power the Inverter and supply charger power to the Battery.

Typical Static UPS Congurations

Static UPS systems modules are available in three basic types congurations known as Standby, Line Interactive, and Double Conversion. See the Section 41 in this guide for details on all the UPS congurations available from Eaton. The lighter power ratings are likely to be one of the rst two types congurations,e.g. Standby or Line Interactive. Most medium or large static UPS installations use the Double Conversion technology in one or multiple module congurations conguration, i.e. or multiple UPS units in parallel, and that will be the primary focus of our discussion. Figure 1.4-18 illustrates the one-line diagram of a simple single Double Conversion UPS module. Brief explanations appear for the Standby and Line Interactive UPS systems after the text explaining the Double Conversion static UPS type of system. A. Double Conversion Concept of Operation The basic operation of the Double Conversion UPS is: 1. Normal power is connected to the UPS input through the facility electrical distribution system. This usually involves two input circuits that must come from the same Source.

When the UPS recognizes a requirement to transfer to the Bypass mode it simultaneously turns the Static Switch ON, the Output Breaker to OPEN, and the Bypass Breaker to CLOSE. The Output Breaker opens and the Bypass Breaker closes in about 50 milliseconds. The restoration of normal conditions at the UPS results in the automatic restoration of the UPS module powering the Load through the Rectier/ Charger and Inverter with Load isolation from power quality problems, and the opening of the Bypass circuit.

i ii 1 2 3 4 5 6 7 8 9 10 11 12

Static Double Conversion Advantages

s s s s s

5. The Bypass circuit provides a path for unregulated normal power to be routed around the major electronic sub-assemblies of the UPS to the Load so that the Load can continue to operate during maintenance, or when the UPS electronics fails. The Bypass Static Switch can switch to conducting mode in 150 120 milliseconds.

Addresses all power quality problems. Suitable for applications from 5 kVA to over 2500 kVA. Simple battery systems are sized for application. Long battery backup times and long life batteries are available. Higher reliability is available using redundant UPS modules.

Bypass Breaker (Optional)

UPS Module

13 14

Bypass Static Switch Source Normal Rectifier/Charger Breaker ac dc Inverter dc ac Battery Breaker Output Breaker Load

15 16 17

Battery

18
Figure 1.4-18. Typical Static UPS, Double Conversion Type with Battery Backup

19 20 21
CA08104001E For more information visit: www.EatonElectrical.com

1.4-26 Power Distribution Systems Uninterruptible Power Systems (UPS)

TOC

Index

June 2006
Sheet 0100

Master TOC

i ii 1 2 3 4

Static Double Conversion Disadvantages

s s

s s s

5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

s s s s

Battery systems, battery maintenance, and battery replacement are required. Large space requirement for battery systems (higher life takes more space, e.g., 500 kW takes 80 to 200 sq.ft. depending upon the type of battery used, VRLA 10 year, VRLA 20 year or ooded). Limited discharge cycles of battery system. Narrow temperature range for application. Efciencies are in the 90 94% range, which is lower than some line interactive congurations. Bypass mode places load at risk unless bypass has UPS backup. Redundancy of UPS modules results in higher costs. Output faults are cleared by the bypass circuit. Output rating of the UPS is 150% for 30 seconds. Battery disposal and safety issues exist.

3. The Battery stores dc energy for use by the Inverter when input power to the UPS fails. The amount of power available from the dc Battery system and time to discharge voltage is a function of the type of Battery selected and the ampere-hour sized used. Battery systems should be sized for the anticipated outage. 4. The dc link connects the output of the Rectier/Charger to the input of the Inverter and to the Battery. Typically the Rectier/Charger is sized only to supply charger power to the Battery, and is rated far lower than in the Double Conversion UPS. 5. The Bypass circuit provides a direct connection of input source to the Load. The Load operates from unregulated power. The Bypass Static Switch can switch to non-conducting mode in 150 120 milliseconds. When the UPS recognizes the loss of normal input power it transfers to Battery / Inverter mode by simultaneously turning the Inverter ON and the Static Switch OFF.

C. Static Line Interactive UPS Concept of Operation The basic operation of the Line Interactive UPS is: 1. The Line Interactive type of UPS has a different topology than the Static Double Conversion and Standby systems. The normal input power is connected to the Load in Parallel with a Battery and bi-directional Inverter/Charger assembly. The input source usually terminates at a line inductor and the output of the inductor is connected to the Load in parallel with the Battery and Inverter/ Charger circuit. See Figure 1.4-20 for further details. 2. The traditional Rectier circuit is eliminated and this results in a smaller footprint and weight reduction. However, line conditioning is compromised. 3. When the input power fails, the Battery/Inverter Charger circuit reverses power and supplies the Load with regulated power.

B. Standby UPS Concept of Operation The basic operation of the Standby UPS is: 1. The Standby UPS topology is similar to the Double Conversion type, but the operation of the UPS is different in signicant ways. Normal power is connected to the UPS input through the facility electrical distribution system. This usually involves two input circuits that must come from the same Source. See Figure 1.4-19 for details. 2. The Rectier/Charger function converts the normal ac power to dc power to charge the Battery only and does not simultaneously power the Inverter. The Load is connected to the input source through the Bypass static switch. The Inverter is in the standby mode ready to serve the load from Battery power if the input power source fails.

Static Line Interactive UPS Advantages

Slight improvement of power conditioning over Standby UPS systems. s Small footprints and weights. s Efcient design. s Batteries are sized for the application.
s

Static Standby UPS Advantages

Lower costs than double conversion. Rectier and charger are economically sized. s Efcient design. s Batteries are sized for the application.
s s

Static Line Interactive UPS Disadvantages

s s s s

Static Standby UPS Disadvantages

s s s s

s s s s

Impractical over 2 kVA. Little to no isolation of load from power quality disturbances. Standby power is from battery alone. Battery systems, battery maintenance, and battery replacement are required. Limited discharge cycles of battery system. Narrow temperature range for application. Output faults are cleared by the bypass circuit. Battery disposal and safety issues exist.

s s s

Impractical over 5 kVA. Not as good conditioning as double conversion. Standby power is from battery alone. Battery systems, battery maintenance, and battery replacement are required. Limited discharge cycles for the battery system. Narrow temperature range for application. Battery disposal and safety issues exist.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0101

TOC

Index

Power Distribution Systems Uninterruptible Power Systems (UPS)

1.4-27

Master TOC

UPS Module

i ii 1 2

Bypass Static Switch

Source Normal Breaker Rectifier/ Charger ac dc Battery Breaker Inverter dc ac Output Breaker

Load

3 4 5 6 7

Battery

Figure 1.4-19. Typical Static UPS, Standby Type with Battery Backup

8
UPS Module

9
Source Inductor Load

10 11 12 13

Bidirectional Inverter/Charger dc ac

14
Battery

15 16

Figure 1.4-20. Typical Static UPS, Line Interactive Type with Battery Backup

17 18 19 20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-28 Power Distribution Systems System Application Considerations

Other Application Considerations

TOC

Index

June 2006
Sheet 0102

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Secondary Voltage
The choice between 208Y/120 V and 480Y/277 V secondary distribution for commercial and institutional buildings depends on several factors. The most important of these are size and types of loads (motors, uorescent lighting, incandescent lighting, receptacles) and length of feeders. In general, large motor and uorescent lighting loads, and long feeders, will tend to make the higher voltages, such as 480Y/277 V, more economical. Very large loads and long runs would indicate the use of medium voltage distribution and loadcenter unit substations close to the loads. Conversely, small loads, short runs, and a high percentage of incandescent lighting would favor lower utilization voltages such as 208Y/120 V. Industrial installations, with large motor loads, are almost always 480 V, often ungrounded delta or resistance grounded delta or wye systems (see section on ground fault protection).

Technical Factors
The principal advantage of the use of higher secondary voltages in buildings is that for a given load, less current means smaller conductors and lower voltage drop. Also, a given conductor size can supply a large load at the same voltage drop in volts, but a lower percentage voltage drop because of the higher supply voltage. Fewer or smaller circuits can be used to transmit the power from the service entrance point to the nal distribution points. Smaller conductors can be used in many branch circuits supplying power loads, and a reduction in the number of lighting branch circuits is usually possible. It is easier to keep voltage drops within acceptable limits on 480-volt circuits than on 208-volt circuits. When 120-volt

loads are supplied from a 480-volt system through step-down transformers, voltage drop in the 480-volt supply conductors can be compensated for by the tap adjustments on the transformer, resulting in full 120-volt output. Since these transformers are usually located close to the 120-volt loads, secondary voltage drop should not be a problem. If it is, taps may be used to compensate by raising the voltage at the transformer. The interrupting ratings of circuit breakers and fuses at 480 volts have increased considerably in recent years, and protective devices are now available for any required fault duty at 480 volts. In addition, many of these protective devices are current limiting, and can be used to protect downstream equipment against these high fault currents.

Elevator Panel T Ty Typical

Practical Factors
Since most low voltage distribution equipment available is rated for up to 600 volts, and conductors are insulated for 600 volts, the installation of 480-volt systems uses the same techniques and is essentially no more difcult, costly, or hazardous than for 208-volt systems. The major difference is that an arc of 120 volts to ground tends to be selfextinguishing, while an arc of 277 volts to ground tends to be self-sustaining and likely to cause severe damage. For this reason, the National Electrical Code requires ground fault protection of equipment on grounded wye services of more than 150 volts to ground but not exceeding 600 volts phase-to-phase (for practical purpose, 480Y/277 V services), for any service disconnecting means rated 1000 amperes or more. The National Electrical Code permits voltage up to 300 volts to ground on circuits supplying permanently installed electric discharge lamp xtures, provided the luminaires do not have an integral manual switch and are mounted at least 8 feet (2.4 m) above the oor. This permits a 3-phase, 4-wire, solidly grounded 480Y/277-volt system to supply directly all of the uorescent and high-intensity discharge (HID) lighting in a building at 277 volts, as well as motors at 480 volts.

Typical V VA HVAC Panel

Emergency Lighting Panel (Typical Every T Ty Third Floor)

480Y/277 208Y/120 V Panel Panel Dry Ty 480-208Y/120 V (Typical Every Floor) T Ty V VA HVAC Feeder Busway Riser Emergency Lighting Riser

T Ty Typical

Elevator Riser

Building and Miscellaneous Loads

T Ty Typical

Typical

T Ty Typical

T Ty Typical Spare

Typical

4000 A Main CB CTs T Ts s Utility g

Automatic Transfer Switch T Tr Gen. CB Emergency or Standby Generator

Utility Service

V 100,000 A Available Fault Current A Av

Figure 1.4-21. Typical Power Distribution and Riser Diagram for a Commercial Ofce Building
Include ground fault trip.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0103

TOC

Index

Power Distribution Systems System Application Considerations

Other Application Considerations
Motors and controls are another cause of wasted energy that can be reduced. New, energy efcient motor designs are available using more and better core steel, and larger windings. For any motor operating 10 or more hours per day, it is recommended to use the energy-efcient types. These motors have a premium cost of about 20% more than standard motors. Depending on loading, hours of use, and the cost of energy, the additional initial cost could be repaid in energy saved within a few months, and it rarely takes more than two years. Since, over the life of a motor, the cost of energy to operate it is many times the cost of the motor itself, any motor with many hours of use should be of the energy-efcient type. Where a motor drives a load with variable output requirements such as a centrifugal pump or a large fan, customary practice has been to run the motor at constant speed, and to throttle the pump output or use inlet vanes or outlet dampers on the fan. This is highly inefcient and wasteful of energy. In recent years, solid-state variablefrequency, variable-speed drives for ordinary induction motors have been available, reliable, and relatively inexpensive. Using a variable-speed drive, the throttling valves or inlet vanes or output dampers can be eliminated, saving their initial cost, and energy will be saved over the life of the system. An additional benet of both energyefcient motors and variable-speed drives (when operated at less than full speed) is that the motors operate at reduced temperatures, resulting in increased motor life. Transformers have inherent losses. Transformers, like motors, are designed for lower losses by using more and better core materials, larger conductors, etc., and this results in increased initial cost. Since the 480-volt to 208Y/120-volt stepdown transformers in an ofce building are usually energized 24 hours a day, savings from lower losses can be substantial, and should be considered in all transformer specications. One method of obtaining reduced losses is to specify transformers with 220C insulation systems designed for 150C average winding temperature

1.4-29

Master TOC

Economic Factors
Utilization equipment suitable for principal loads in most buildings is available for either 480-volt or 208-volt systems. 3-phase motors and their controls can be obtained for either voltage, and for a given horsepower are less costly at 480 volts. Fluorescent and HID lamps can be used with either 277- or 120-volt ballasts. However, in almost all cases, the installed equipment will have a lower total cost at the higher voltage.

rise, with no more than 80C (or sometimes 115C) average winding temperature rise at full load. A better method would be to evaluate transformer losses, based on actual loading cycles throughout the day, and consider the cost of losses as well as the initial cost of the transformers in purchasing. NEMA standard TP-1 is being adopted by many states and is another method of energy efcient design. NEMA TP-1 establishes minimum operating efciencies for each distribution transformer size at a loading equal to 35% of the transformer full load kVA. The 35% loading value in the NEMA standard reects eld studies conducted by the U.S. Department of Energy which showed that dry-type transformers installed in commercial facilities are typically loaded at an average of 35% of their full load capacity over a 24 hour time period. Table 1.4-8 compares losses for both low temperature rise and TP-1 transformers using a 75 kVA design. Table 1.4-8. Load Losses
Temp. Load Losses in Watts Rise C No 25% 35% 50% 75% Full Loss Load Load Load Load Load 150 115 80 TP-1 150 360 420 500 230 490 480 535 310 620 610 615 480 885 805 730 745 1,535 2,450 1,170 1,950 945 1,410 1,235 2,280

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Energy Conservation
Because of the greatly increased cost of electrical power, designers must consider the efciency of electrical distribution systems, and design for energy conservation. In the past, especially in commercial buildings, design was for lowest rst cost, because energy was inexpensive. Today, even in the speculative ofce building, operating costs are so high that energy-conserving designs can justify their higher initial cost with a rapid payback and continuing savings. Buildings that must meet LEED certications may require energy saving designs. There are four major sources of energy conservation in a commercial building the lighting system, the motors and controls, the transformers, and the HVAC system. The lighting system must take advantage of the newest equipment and techniques. New light sources, familiar light sources with higher efciencies, solid-state ballasts with dimming controls, use of daylight, environmental design, efcient luminaires, computerized or programmed control, and the like, are some of the methods that can increase the efciency of lighting systems. They add up to providing the necessary amount of light, with the desired color rendition, from the most efcient sources, where and when it is needed, and not providing light where or when it is not necessary. Using the best of techniques, ofce spaces that originally required as much as 3.5 watts per square foot have been given improved lighting, with less glare and higher visual comfort, using as little as 1.0 to 2.0 watts per square foot. In an ofce building of 200,000 square feet (60,960 m), this could mean a saving of 400 kW, which, at $.05 per kWh, 250 days per year, 10 hours per day, could save $50,000 per year in energy costs. Obviously, efcient lighting is a necessity.

HVAC systems have traditionally been very wasteful of energy, often being designed for lowest rst cost. This, too, is changing. For example, reheat systems are being replaced by variable air volume systems, resulting in equal comfort with substantial increases in efciency. While the electrical engineer has little inuence on the design of the HVAC system, he/she can specify that all motors with continuous or long duty cycles are specied as energy efcient types, and that the variable-air-volume fans do not use inlet vanes or outlet dampers, but are driven by variablespeed drives. Variable-speed drives can often be desirable on centrifugal compressor units as well. Since some of these requirements will be in HVAC specications, it is important for the energy-conscious electrical engineer to work closely with the HVAC engineer at the design stage.

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-30 Power Distribution Systems System Application Considerations

Other Application Considerations

TOC

Index

June 2006
Sheet 0104

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Building Control Systems

In order to obtain the maximum benet from these energy-saving lighting, power, and HVAC systems, they must be controlled to perform their functions most efciently. Constant monitoring would be required for manual operation, so some form of automatic control is required. The simplest of these energy-saving controls, often very effective, is a time clock to turn various systems on and off. Where exible control is required, programmable controllers may be used. These range from simple devices, similar to multifunction time clocks, up to full microprocessor-based, fully programmable devices, really small computers. For complete control of all building systems, computers with specialized software can be used. Computers can not only control lighting and HVAC systems, and provide peak demand control, to minimize the cost of energy, but they can perform many other functions. Fire detection and alarm systems can operate through the computer, which can also perform auxiliary functions such as elevator control and building communication in case of re. Building security systems, such as closedcircuit television monitoring, door alarms, intruder sensing, can be performed by the same building computer system. The time clocks, programmable controllers, and computers can obtain data from external sensors and control the lighting, motors, and other equipment by means of hard wiring-separate wires to and from each piece of equipment. In the more complex systems, this would result in a tremendous number of control wires, so other methods are frequently used. A single pair of wires, with electronic digital multiplexing, can control or obtain data from many different points. Sometimes, coaxial cable is used with advanced signaling equipment. Some systems dispense with control wiring completely, sending and receiving digital signals over the power wiring. The newest systems may use ber-optic cables to carry tremendous quantities of data, free from electromagnetic interference. The method used will depend on the type, number, and complexity of functions to be performed.

Because building design and control for maximum energy saving is important and complex, and frequently involves many functions and several systems, it is necessary for the design engineer to make a thorough building and environmental study, and to weigh the costs and advantages of many systems. The result of good design can be economical, efcient operation. Poor design can be wasteful, and extremely costly.

One reason is that most cogenerators are connected to feeders serving other customers. Utilities desire to reclose the feeder after a transient fault is cleared. Reclosing in most cases will damage the cogenerator if it had remained connected to their system. Islanding is another reason why the utility insists on the disconnection of the cogenerator. Islanding is the event that after a fault in the utilitys system is cleared by the operation of the protective devices, a part of the system may continue to be supplied by cogeneration. Such a condition is dangerous to the utilitys operation during restoration work. Major cogenerators are connected to the subtransmission or the transmission system of a utility. Major cogenerators have buy-sell agreements. In such cases utilities use a trip transfer scheme to trip the cogenerator breaker. Guidelines that are given in ANSI Guide Standard 1001 are a good starting point, but the entire design should be coordinated with the utility.

Cogeneration
Cogeneration is another outgrowth of the high cost of energy. Cogeneration is the production of electric power concurrently with the production of steam, hot water, and similar energy uses. The electric power can be the main product, and steam or hot water the by-product, as in most commercial installations, or the steam or hot water can be the most required product, and electric power a by-product, as in many industrial installations. In some industries, cogeneration has been common practice for many years, but until recently it has not been economically feasible for most commercial installations. This has been changed by the high cost of purchased energy, plus a federal law (Public Utility Regulatory Policies Act, known as PURPA) that requires public utilities to purchase any excess power generated by the cogeneration plant. In many cases, practical commercial cogeneration systems have been built that provide some or all of the electric power required, plus hot water, steam, and sometimes steam absorption-type air conditioning. Such cogeneration systems are now operating successfully in hospitals, shopping centers, high-rise apartment buildings and even commercial ofce buildings. Where a cogeneration system is being considered, the electrical distribution system becomes more complex. The interface with the utility company is critical, requiring careful relaying to protect both the utility and the cogeneration system. Many utilities have stringent requirements that must be incorporated into the system. Proper generator control and protection is necessary, as well. An on-site electrical generating plant tied to an electrical utility, is a sophisticated engineering design. Utilities require that when the protective device at their substation opens that the device connecting a cogenerator to the utility open also.

Emergency Power
Most areas have requirements for emergency and standby power systems. The National Electrical Code does not specically call for any emergency or standby power, but does have requirements for those systems when they are legally mandated and classed as emergency (Article 700), legally required standby (Article 701) by municipal, state, federal, or other codes, or by any governmental agency having jurisdiction. Optional standby systems, not legally required, are also covered in the NEC (Article 702). Emergency systems are intended to supply power and illumination essential for safety to human life, when the normal supply fails. NEC requirements are stringent, requiring periodic testing under load and automatic transfer to emergency power supply on loss of normal supply. See Figure 1.4-22 on Page 1.4-31. All wiring from emergency source to emergency loads must be kept separate from all other wiring and equipment, in its own distribution and raceway system, except in transfer equipment enclosures and similar locations. The most common power source for large emergency loads is an engine-generator set, but the NEC also permits the emergency supply (subject to local code requirements) to be storage

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0105

TOC

Index

Power Distribution Systems System Application Considerations

Other Application Considerations

1.4-31

Master TOC

Utility Source

i
Typical Application: Three engine generator sets serve the load, plus one additional engine generator set for redundancy to achieve N+1 level of performance. Open or Closed transition is available.

ii
G1 Revenue Metering HMI Touchscreen 52G1 Main Service 52G2 52G3 52G4 D1 D2 D3 D4 G2 G3 G4 Paralleling Switchgear with Distribution

1 2 3 4 5

To Normal Distribution Circuits

To Emergency Circuits

ATS1

ATS2

ATS3

ATS4

6 7

EDP1

EDP2

EDP3

EDP4

8
Optional Remote PC with Software LP1 BP1 LP2 BP2 LP3 BP3 LP4 BP4

9 10

Figure 1.4-22. Typical Emergency Power System batteries, uninterruptible power supplies, a separate emergency service, or a connection to the service ahead of the normal service disconnecting means. Unit equipment for emergency illumination, with a rechargeable battery, a charger to keep it at full capacity when normal power is on, one or more lamps, and a relay to connect the battery to the lamps on loss of normal power, is also permitted. Because of the critical nature of emergency power, ground fault protection is not required. It is considered preferable to risk arcing damage, rather than to disconnect the emergency supply completely. For emergency power, ground fault alarm is required by NEC 700.7(D) to indicate a ground fault in solidly grounded wye emergency systems of more than 150 volts to ground and circuit-protective devices rated 1000 amperes or more. Legally required standby systems, as required by the governmental agency having jurisdiction, are intended to supply power to selected loads, other than those classed as emergency systems, on loss of normal power. These are usually loads not essential to human safety, but loss of which could create hazards or hamper rescue
CA08104001E

or re-ghting operations. NEC requirements are similar to those for emergency systems, except that wiring may occupy the same distribution and raceway system as the normal wiring if desired. Optional standby systems are those not legally required, and are intended to protect private business or property where life safety does not depend on performance of the system. Optional systems can be treated as part of the normal building wiring system. Both legally required and optional standby systems should be installed in such a manner that they will be fully available on loss of normal power. It is preferable to isolate these systems as much as possible, even though not required by code. Where the emergency or standby source, such as an engine generator or separate service, has capacity to supply the entire system, the transfer scheme can be either a full-capacity automatic transfer switch, or, less costly but equally effective, normal and emergency main circuit breakers, electrically interlocked such that on failure of the normal supply the emergency supply is connected to the load. However, if the emergency or standby source does not have capacity for the
For more information visit: www.EatonElectrical.com

full load, as is usually the case, such a scheme would require automatic disconnection of the nonessential loads before transfer. Simpler and more economical in such a case is a separate emergency bus, supplied through an automatic transfer switch, to feed all critical loads. The transfer switch connects this bus to the normal supply, in normal operation. On failure of the normal supply, the engine-generator is started, and when it is up to speed the automatic switch transfers the emergency loads to this source. On return of the normal source, manual or automatic retransfer of the emergency loads can take place.

11 12 13 14 15 16 17 18 19 20 21

Peak Shaving
Many installations now have emergency or standby generators. In the past, they were required for hospitals and similar locations, but not common in ofce buildings or shopping centers. However, many costly and unfortunate experiences during utility blackouts in recent years have led to the more frequent installation of engine generators in commercial and institutional systems for safety and for supplying important loads. Industrial plants, especially in

1.4-32 Power Distribution Systems System Application Considerations

Other Application Considerations
process industries, usually have some form of alternate power source to prevent extremely costly shutdowns. These standby generating systems are critical when needed, but they are needed only infrequently. They represent a large capital investment. To be sure that their power will be available when required, they should be tested periodically under load. The cost of electric energy has risen to new high levels in recent years, and utilities bill on the basis not only of power consumed, but also on the basis of peak demand over a small interval. As a result, a new use for in-house generating capacity has developed. Utilities measure demand charges on the basis of the maximum demand for electricity in any given specic period (typically 15 or 30 minutes) during the month. Some utilities have a demand ratchet clause that will continue demand charges on a given peak demand for a full year, unless a higher peak results in even higher charges. One large load, coming on at a peak time, can create higher electric demand charges for a year. Obviously, reducing the peak demand can result in considerable savings in the cost of electrical energy. For those installations with engine generators for emergency use, modern control systems (computers or programmable controllers) can monitor the peak demand, and start the engine-generator to supply part of the demand as it approaches a preset peak value. The engine-generator must be selected to withstand the required duty cycle. The simplest of these schemes transfer specic loads to the generator. More complex schemes operate the generator in parallel with the normal utility supply. The savings in demand charges can reduce the cost of owning the emergency generator equipment. In some instances, utilities with little reserve capacity have helped nance the cost of some larger customerowned generating equipment. In return, the customer agrees to take some or all of his load off the utility system and on to his own generator at the request of the utility (with varying limitations) when the utility load approaches capacity. In some cases, the customers generator is paralleled with the utility to help supply the peak utility loads, with the utility buying the supplied power. Some utilities have been able to delay large capital expenditures for additional generating capacity by such arrangements. It is important that the electrical system designer providing a substantial source of emergency and standby power investigate the possibility of using it for peak shaving, and even of partial utility company nancing. Frequently, substantial savings in power costs can be realized for a small additional outlay in distribution and control equipment. Peak shaving equipment operating in parallel with the utility are subject to the comments made under cogeneration as to separation from the utility under fault conditions.

TOC

Index

June 2006
Sheet 0106

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Some reduction or attenuation takes place through building walls, the remainder may be reected in various directions, resulting in a build-up or apparent higher levels, especially if resonance occurs because of room dimensions or material characteristics.

Area Consideration
In determining permissible sound levels within a building, it is necessary to consider how the rooms are to be used and what levels may be objectionable to occupants of the building. The ambient sound level values given in Table 1.4-9 are representative average values and may be used as a guide in determining suitable building levels. Decrease in sound level varies at an approximate rate of 6 decibels for each doubling of the distance from the source of sound to the listener. For example, if the level 6 feet (1.8 m) from a transformer is 50 dB, the level at a distance of 12 feet (3.7 m) would be 44 dB and at 24 feet (7.3 m) the level decreases to 38 dB, etc. However, this rule applies only to equipment in large areas equivalent to an outof-door installation, with no nearby reecting surfaces. Table 1.4-9. Typical Sound Levels
Description Average Decibel Level (dB)

Sound Levels
Sound Levels of Electrical Equipment for Ofces, Hospitals, Schools and Similar Buildings
Insurance underwriters and building owners desire and require that the electrical apparatus be installed for maximum safety and the least interference with the normal use of the property. Architects should take particular care with the designs for hospitals, schools and similar buildings to keep the sound perception of such equipment as motors, blowers and transformers to a minimum. Even though transformers are relatively quiet, resonant conditions may exist near the equipment which will amplify their normal 120 Hz hum. Therefore, it is important that consideration be given to the reduction of amplitude and to the absorption of energy at this frequency. This problem begins in the designing stages of the equipment and the building. There are two points worthy of consideration: 1) What sound levels are desired in the normally occupied rooms of this building? 2) To effect this, what sound level in the equipment room and what type of associated acoustical treatment will give the most economical installation overall? A relatively high sound level in the equipment room does not indicate an abnormal condition within the apparatus. However, absorption may be necessary if sound originating in an unoccupied equipment room is objectionable outside the room. Furthermore, added absorption material usually is desirable if there is a build-up of sound due to reections.

Radio, Recording and TV Studios 25 30 Theatres and Music Rooms 30 35 Hospitals, Auditoriums and Churches 35 40 Classrooms and Lecture Rooms 35 40 Apartments and Hotels 35 45 Private Ofces and Conference Rooms 40 45 Stores Residence (Radio, TV Off) and Small Ofces Medium Ofce (3 to 10 Desks) Residence (Radio, TV On) Large Store (5 or More Clerks) Factory Ofce Large Ofce Average Factory Average Street 45 55 53 58 60 61 61 64 70 80

Transformer Sound Levels

Transformers emit a continuous 120 Hz hum with harmonics when connected to 60 Hz circuits. The fundamental frequency is the hum which annoys people primarily because of its continuous nature. For purposes of reference, sound measuring instruments convert the different frequencies to 1000 Hz and a 40 dB level. Transformer sound levels based on NEMA publication TR-1 are listed in Table 1.4-10.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0107

TOC

Index

Power Distribution Systems System Application Considerations

Other Application Considerations

1.4-33

Master TOC

Table 1.4-10. Maximum Average Sound Levels Decibels

kVA Liquid-Filled Transformers Self-Cooled Rating (OA) 300 500 750 1000 1500 2000 2500 3000 3750 5000 6000 7500 10,000 55 56 58 58 60 61 62 63 64 65 66 67 68 Forced-Air Cooled Rating (FA) 67 67 67 67 67 67 67 67 67 68 69 70 Dry-Type Transformers Self-Cooled Rating (AA) 58 60 64 64 65 66 68 68 70 71 72 73 Forced-Air Cooled Rating (FA) 67 67 67 67 68 69 71 71 73 73 74 75 76

Since values given in Table 1.4-10 are in general higher than those given in Table 1.4-9, the difference must be attenuated by distance and by proper use of materials in the design of the building. An observer may believe that a transformer is noisy because the level in the room where it is located is high. Two transformers of the same sound output in the same room increase the sound level in the room approximately 3 dB, and three transformers by about 5 dB, etc.

Sounds due to structure-transmitted vibrations originating from the transformer are lowered by mounting the transformers on vibration dampeners or isolators. There are a number of different sound vibration isolating materials which may be used with good results. Dry-type power transformers are often built with an isolator mounted between the transformer support and case members. The natural period of the core and coil structure when mounted

on vibration dampeners is about 10% of the fundamental frequency. The reduction in the transmitted vibration is approximately 98%. If the oor or beams beneath the transformer are light and exible, the isolator must be softer or have improved characteristics in order to keep the transmitted vibrations to a minimum. (Enclosure covers and ventilating louvers are often improperly tightened or gasketed and produce unnecessary noise). The building structure will assist the dampeners if the transformer is mounted above heavy oor members or if mounted on a heavy oor slab. Positioning of the transformer in relation to walls and other reecting surfaces has a great effect on reected noise and resonances. Often, placing the transformer at an angle to the wall, rather than parallel to it, will reduce noise. Electrical connections to a substation transformer should be made with exible braid or conductors; connections to an individually mounted transformer should be in exible conduit.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.4-34 Power Distribution Systems

TOC Index

June 2006
Sheet 0108

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

This page intentionally left blank.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0109

TOC

Index

Power Distribution Systems Reference Data

IEEE Protective Relay Numbers

1.5-1

Master TOC

Table 1.5-1. Selected IEEE Device Numbers for Switchgear Apparatus

Device Number 2 Function Time-delay starting or closing relay Denition Typical Uses

i ii 1 2 3 4 5

A device which functions to give a desired amount Used for providing a time-delay for of time delay before or after any point of operation re-transfer back to the normal source in a switching sequence or protective relay system, in an automatic transfer scheme. except as specically provided by device functions 48, 62 and 79 described later. A device whose principal function is to connect a machine to its source of starting voltage. A device which operates to initiate or cause the automatic transfer of a machine from the starting to the running power connection. A device which functions when the circuit admittance, impedance or reactance increases or decreases beyond predetermined limits. A device which functions to raise or to lower the temperature of a machine or other apparatus, or of any medium, when its temperature falls below or rises above, a predetermined level. A device that operates when the ratio of voltage to frequency is above a preset value or is below a different preset value. The relay may have any combination of instantaneous or time delayed characteristics. A device which operates when two ac circuits are within the desired limits of frequency, phase angle or voltage, to permit or cause the paralleling of these two circuits. A device which functions on a given value of undervoltage. Used to transfer a reduced voltage starter from starting to running.

6 19

Starting circuit breaker Starting to running transition timer

21

Distance relay

23

Temperature control device

Used as a thermostat to control space heaters in outdoor equipment.

24

Volts per hertz relay

6
In a closed transition breaker transfer, a 25 relay is used to ensure two-sources are synchronized before paralleling. Cutler-Hammer FP-5000 feeder protective relay. Used to initiate an automatic transfer when a primary source of power is lost. Cutler-Hammer FP-5000/ FP-4000/MP-4000 protective relays. Used to remotely indicate that a protective relay has functioned, or that a circuit breaker has tripped. Typically, a mechanical drop type annunciator panel is used. Used to prevent reverse power from feeding an upstream fault. Often used when primary backup generation is utilized in a facility. CutlerHammer FP-5000 protective relay. Used to indicate the position of a drawout circuit breaker (TOC switch).

25

Synchronizing or synchronism check device

7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

27

Undervoltage relay

30

Annunciator relay

A non-automatically reset device that gives a number of separate visual indications upon the functioning of protective devices, and which may also be arranged to perform a lockout function. A relay which functions on a desired value of power ow in a given direction, or upon reverse power resulting from arc back in the anode or cathode circuits of a power rectier. A device which makes or breaks contact when the main device or piece of apparatus, which has no device function number, reaches a given point.

32

Directional power relay

33

Position switch

34

Master sequence device

A device such as a motor-operated multi-contact switch, or the equivalent, or a programmable device, that establishes or determines the operating sequence of the major devices in equipment during starting and stopping or during sequential switching operations. A relay which functions when the current or power ow decreases below a predetermined value. Cutler-Hammer MP-3000/MP-4000 motor protective relays.

37 38

Undercurrent or underpower relay Bearing protective device

A device which functions on excessive bearing Cutler-Hammer MP-3000/MP-4000 temperature, or on other abnormal mechanical motor protective relays. conditions, such as undue wear, which may eventually result in excessive bearing temperature. A device that functions on a given or abnormally high or low value or failure of machine eld current, or on an excessive value of the reactive component of armature current in an ac machine indicating abnormally high or low eld excitation. A device which functions to apply, or to remove, the eld excitation of a machine. A device whose function is to connect a machine to its source of running or operating voltage. This function may also be used for a device, such as a contactor, that is used in series with a circuit breaker or other fault-protecting means, primarily for frequent opening and closing of the circuit.

40

Field relay

41 42

Field circuit breaker Running circuit breaker

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-2

Power Distribution Systems Reference Data

IEEE Protective Relay Numbers
Table 1.5-1. Selected IEEE Device Numbers for Switchgear Apparatus (Continued)
Device Number 43 Function Manual transfer or selector device Denition A manually operated device that transfers control or potential circuits in order to modify the plan of operation of the associated equipment or of some of the associated devices. A device that functions to start the next available unit in multiple-unit equipment upon the failure or non-availability of the normally preceding unit.

TOC

Index

June 2006
Sheet 0110

Master TOC

i ii 1 2 3 4 5 6 7 8

Typical Uses

44

Unit sequence starting relay

46

Reverse-phase, or phase balance, current relay A relay which functions when the polyphase currents are of reverse-phase sequence, or when the polyphase currents are unbalanced or contain the negative phase-sequence components above a given amount. Phase-sequence voltage relay A relay which functions upon a predetermined value of polyphase voltage in the desired phase sequence.

Cutler-Hammer FP-5000/FP-4000 feeder protective relays and MP-3000/ MP-4000 motor protective relays.

47

Cutler-Hammer FP-5000/FP-4000 feeder protective relays and MP-3000/ MP-4000 motor protective relays.

48

Incomplete sequence relay

A relay that generally returns the equipment to the normal, or off, position and locks it out of the normal starting, or operating or stopping sequence is not properly completed within a predetermined amount of time. If the device is used for alarm purposes only, it should preferably be designated as 48A (alarm). A relay that functions when the temperature of a machine armature, or other load carrying winding or element of a machine, or the temperature of a power rectier or power transformer (including a power rectier transformer) exceeds a predetermined value. Cutler-Hammer MP-3000/MP-4000 motor protective relays.

49

Machine, or transformer, thermal relay

50

9 10 11 12 13 14
52 51

Instantaneous overcurrent, or rate-of-rise relay A relay that functions instantaneously on an excessive value of current, or an excessive rate of current rise, thus indicating a fault in the apparatus of the circuit being protected.

Used for tripping a circuit breaker instantaneously during a high level short circuit. Can trip on phasephase (50), phase-neutral (50N), phase-ground (50G) faults. Cutler-Hammer Digitrip 3000, FP-5000/FP-4000 protective relays, MP-3000/MP-4000 motor protective relays. Used for tripping a circuit breaker after a time delay during a sustained overcurrent. Used for tripping a circuit breaker instantaneously during a high level short circuit . Can trip on phase (51), neutral (51N) or ground (51G) overcurrents. Cutler-Hammer Digitrip 3000, FP-5000/FP-4000 protective relays, MP-3000/MP-4000 motor protective relays. A term applied typically to medium voltage circuit breakers, or low voltage power circuit breakers. Cutler-Hammer VCP-W Vacuum Circuit Breaker, Magnum DS Low Voltage Power Circuit Breaker

ac time overcurrent relay

A relay with either a denite or inverse time characteristic that functions when the current in an ac circuit exceeds a predetermined value.

ac circuit breaker

15 16 17 18 19 20 21
60 Voltage or current balance relay 53 Exciter or dc generator relay

A device that is used to close and interrupt an ac power circuit under normal conditions or to interrupt this circuit under fault or emergency conditions.

A device that forces the dc machine eld excitation to build up during starting or that functions when the machine voltage has built up to a given value. A relay that operates when the power factor in an ac circuit rises above or below a predetermined value.

55

Power factor relay

Cutler-Hammer FP-5000/FP-4000 feeder protective relays and MP-4000 motor protective relay.

56

Field application relay

A device that automatically controls the application of the eld excitation to an ac motor at some predetermined point in the slip cycle. A relay that functions on a given value of overvoltage. Used to trip a circuit breaker, protecting downstream equipment from sustained overvoltages. Cutler-Hammer FP-5000/FP-4000 feeder protective relays and MP-4000 motor protective relay.

59

Overvoltage relay

A relay that operates on a given difference in voltage, or current input or output of two circuits.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0111

TOC

Index

Power Distribution Systems Reference Data

IEEE Protective Relay Numbers

1.5-3

Master TOC

Table 1.5-1. Selected IEEE Device Numbers for Switchgear Apparatus (Continued)
Device Number 62 Function Time-delay stopping or opening relay Denition A time-delay relay that serves in conjunction with the device that initiates the shutdown, stopping, or opening operation in an automatic sequence. A switch which operates on given values or on a given rate of change of pressure. Typical Uses Used in conjunction with a 27 device to delay tripping of a circuit breaker during a brief loss of primary voltage, to prevent nuisance tripping. Used to protect a transformer during a rapid pressure rise during a short circuit. This device will typically act to open the protective devices above and below the transformer. Typically used with a 63-X auxiliary relay to trip the circuit breaker.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14

63

Pressure switch

64

Ground protective relay

A relay that functions on a failure of the insulation Used to detect and act on a groundof a machine, transformer, or of other apparatus to fault condition. In a pulsing high ground, or on ashover of a dc machine to ground. resistance grounding system, a 64 device will initiate the alarm. A device consisting of an assembly of uid, electrical or mechanical control equipment used for regulating the ow of water, steam, or other media to the prime mover for such purposes as starting, holding speed or load, or stopping. A device that functions to allow only a specied Cutler-Hammer MP-3000/MP-4000 number of operations of a given device, or motor protective relays. equipment, or a specied number of successive operations within a given time of each other. It also functions to energize a circuit periodically or for fractions of specied time intervals, or that is used to permit intermittent acceleration or jogging of a machine at low speeds for mechanical positioning. A relay that functions on a desired value of ac overcurrent owing in a predetermined direction. Cutler-Hammer FP-5000 feeder protective relay.

65

Governor

66

Notching or jogging device

67 69

ac directional overcurrent relay Permissive control device

A device that is generally a two-position manually Used as a remote-local switch for operated switch that in one position permits the circuit breaker control. closing of a circuit breaker, or the placing of equipment into operation, and in the other position prevents the circuit breaker to the equipment from being operated. A switch that operates on given values, or on a given rate of change of level. Used to indicate a low liquid level within a transformer tank in order to save transformers from loss-ofinsulation failure. An alarm contact is available as a standard option on a liquid level gauge. It is set to close before an unsafe condition actually occurs.

71

Level Switch

72

dc circuit breaker

A device that is used to close and interrupt a dc power circuit under normal conditions or to interrupt this circuit under fault or emergency conditions. A device that is used to shunt or insert a step of load limiting, shifting or indicating resistance in a power circuit; to switch a space heater in circuit; or to switch a light or regenerative load resistor of a power rectier or other machine in and out of circuit. A device other than an annunciator, as covered under device number 30, which is used to operate, or to operate in connection with, a visible or audible alarm.

73

Load-resistor contactor

15

74

Alarm relay

16 17 18 19 20 21

78

Phase-angle measuring relay

A device that functions at a predetermined phase angle between two voltages, between two currents, or between voltage and current. A relay that controls the automatic closing and locking out of an ac circuit interrupter. Used to automatically reclose a circuit breaker after a trip, assuming the fault has been cleared after the power was removed from the circuit. The recloser will lock-out after a predetermined amount of failed attempts to reclose.

79

ac reclosing relay

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-4

Power Distribution Systems Reference Data

IEEE Protective Relay Numbers
Table 1.5-1. Selected IEEE Device Numbers for Switchgear Apparatus (Continued)
Device Number 81 Function Frequency relay Denition A relay that functions on a predetermined value of frequency either under or over or on normal system frequency or rate of change frequency.

TOC

Index

June 2006
Sheet 0112

Master TOC

i ii 1 2 3 4 5 6 7 8

Typical Uses Used to trip a generator circuit breaker in the event the frequency drifts above or below a given value. Cutler-Hammer FP-5000/FP-4000 feeder protective relays and MP-4000 motor protective relay. Used to transfer control power sources in a double-ended switchgear lineup.

83

Automatic selective control or transfer relay

A relay that operates to select automatically between certain sources or conditions in equipment, or performs a transfer operation automatically. A device that is operated or restrained by a signal transmitted or received via any communications media used for relaying. An electrically operated hand, or electrically, reset relay that functions to shut down and hold an equipment out of service on the occurrence of abnormal conditions.

85

Carrier or pilot-wire relay

86

Locking-out relay

Used in conjunction with protective relays to lock-out a circuit breaker (or multiple circuit breakers) after a trip. Typically required to be manually reset by an operator before the breaker can be reclosed.

87

Differential protective relay

A protective relay that functions on a percentage or Used to protect static equipment, phase angle or other quantitative difference of two such as cable, bus or transformers, currents or of some other electrical quantities. by measuring the current differential between two points. Typically the upstream and/or downstream circuit breaker will be incorporated into the zone of protection. Cutler-Hammer FP-5000 feeder protective relay (87B) and MD-3000 protective relay. A device that functions to regulate a quantity or quantities, such as voltage, current, power, speed, frequency, temperature and load, at a certain value or between certain (generally close) limits for machines, tie lines or other apparatus. A device that operates when the voltage across an open circuit breaker or contactor exceeds a given value in a given direction. A relay that functions to trip a circuit breaker, contactor, or equipment, or to permit immediate tripping by other devices, or to prevent immediate reclosure of a circuit interrupter, in case it should open automatically even though its closing circuit is maintained closed.

90

Regulating device

9 10 11 12 13 14 15 16 17 18 19 20 21
91 Voltage directional relay

94

Tripping or trip-free relay

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0113

TOC

Index

Power Distribution Systems Reference Data

Suggested IEEE Designations for Sufx Letters

1.5-5

Master TOC

Suggested IEEE Designations for Sufx Letters

Auxiliary Devices
These letters denote separate auxiliary devices, such as the following: C CL Closing relay/contactor Auxiliary relay, closed (energized when main device is in closed position) Control switch Down position switch relay Lowering relay Opening relay/contactor Auxiliary relay, open (energized when main device is in open position) Push button Raising relay UP position switch relay Auxiliary relay Auxiliary relay Auxiliary relay

Main Device
The following letters denote the main device to which the numbered device is applied or is related: A AC BP BT C DC E F G M MOC S T TOC Alarm/auxiliary power Alternating current Bypass Bus tie Capacitor Direct current Exciter Feeder/eld Generator/ground Motor/metering Mechanism operated contact Synchronizing/secondary Transformer Truck-operated contacts

Other Sufx Letters

The following letters cover all other distinguishing features, characteristics or conditions not specically described in Auxiliary Devices through Main Device Parts, which serve to describe the use of the device in the equipment, such as: A BF C D E F HS L M O OFF ON R T TDC TDDO TDO TDPU THD Automatic Breaker failure Close Decelerating/down Emergency Failure/forward High speed Local/lower Manual Open Off On Raise/reclosing/remote/reverse Test/trip Time-delay closing contact Time delayed relay coil drop-out Time-delay opening contact Time delayed relay coil pickup Total harmonic distortion

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

CS D L O OP

PB R U X Y Z

Main Device Parts

These letters denote parts of the main device, except auxiliary contacts, position switches, limit switches, and torque limit switches: C CC HC M OC S SI T TC Coil/condenser/capacitor Closing coil/closing contactor Holding coil Operating motor Opening contactor Solenoid Seal-in Target Trip coil

Actuating Quantities
These letters indicate the condition or electrical quantity to which the device responds, or the medium in which it is located, such as the following: A C F I0 I-, I2 I+, I1 P PF S T V VAR VB W Amperes/alternating Current Frequency/fault Zero sequence current Negative sequence current Positive sequence current Power/pressure Power factor Speed Temperature Voltage/volts/vacuum Reactive power Vibration Watts

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-6

Power Distribution Systems Reference Data

Codes and Standards

TOC

Index

June 2006
Sheet 0114

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Codes and Standards

The National Electrical Code (NEC), NFPA Standard No. 70, is the most prevalent electrical code in the United States. The NEC, which is revised every three years, has no legal standing of its own, until it is adopted as law by a jurisdiction, which may be a city, county, or state. Most jurisdictions adopt the NEC in its entirety; some adopt it with variations, usually more rigid, to suit local conditions and requirements. A few large cities, such as New York and Chicago, have their own electrical codes, basically similar to the NEC. The designer must determine which code applies in the area of a specic project. The Occupational Safety and Health Act (OSHA) of 1970 sets uniform national requirements for safety in the workplace anywhere that people are employed. Originally OSHA adopted the 1971 NEC as rules for electrical safety. As the NEC was amended every three years, the involved process for modifying a federal law such as OSHA made it impossible for the act to adopt each new code revision. To avoid this problem, the OSHA administration in 1981 adopted its own code, a condensed version of the NEC containing only those provisions considered related to occupational safety. OSHA was amended to adopt this code, based on NFPA Standard 70E, Part 1, which is now federal law. The NEC is a minimum safety standard. Efcient and adequate design usually requires not just meeting, but often exceeding NEC requirements to provide an effective, reliable, economical electrical system. Many equipment standards have been established by the National Electrical Manufacturers Association (NEMA) and the American National Standards Institute (ANSI). Underwriters Laboratory (UL) has standards that equipment must meet before UL will list or label it. Most jurisdictions and OSHA require that where equipment listed as safe by a recognized laboratory is available, unlisted equipment may not be used. UL is by far the most widely accepted national laboratory, although Factory Mutual Insurance Company lists some equipment, and a number of other

testing laboratories have been recognized and accepted. The Institute of Electrical and Electronic Engineers (IEEE) publishes a number of books (the color book series) on recommended practices for the design of industrial buildings, commercial buildings, emergency power systems, grounding, and the like. Most of these IEEE standards have been adopted as ANSI standards. They are excellent guides, although they are not in any way mandatory.

A design engineer should conform to all applicable codes, and require equipment to be listed by UL or another recognized testing laboratory wherever possible, and to meet ANSI or NEMA standards. ANSI/IEEE recommended practices should be followed to a great extent. In many cases, standards should be exceeded to get a system of the quality required. The design goal should be a safe, efcient, long-lasting, exible, and economical electrical distribution system.

Professional Organizations

American National Standards Institute (ANSI)

Headquarters:
1819 L Street, NW 6th Floor Washington, DC 20036 202-293-8020

National Electrical Manufacturers Association (NEMA)

1300 North 17th Street Suite 1847 Rosslyn, VA 22209 703-841-3200 www.nema.org

Operations:
25 West 43rd Street 4th Floor New York, NY 10036 212-642-4900 www.ansi.org

National Fire Protection Association (NFPA)

1 Battery March Park Quincy, MA 02169-7471 617-770-3000 www.nfpa.org

Institute of Electrical and Electronics Engineers (IEEE)

Headquarters:
3 Park Avenue 17th Floor New York, NY 10016-5997 212-419-7900

Underwriters Laboratories (UL)

333 Pngsten Road Northbrook, IL 60062-2096 847-272-8800 www.ul.com

International Code Council (ICC)

5203 Leesburg Pike Suite 600 Falls Church, VA 22041 1-888-422-7233 www.iccsafe.org

Operations:
445 Hoes Lane Piscataway, NJ 08854-1331 732-981-0060 www.ieee.org

The American Institute of Architects (AIA)

1735 New York Avenue, NW Washington, DC 20006-5292 202-626-7300 www.aia.org

International Association of Electrical Inspectors (IAEI)

901 Waterfall Way Suite 602 Richardson, TX 75080-7702 972-235-1455 www.iaei.org

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0115

TOC

Index

Power Distribution Systems Reference Data

Motor Protective Device Data
Table 1.5-2. Motor Circuit Protector (MCP), Circuit Breaker and Fusible Switch Selection Guide
Horsepower Full Load Fuse Size NEC 430.52 Amperes Maximum (NEC) FLA Amperes Recommended Cutler-Hammer Circuit Breaker Motor Circuit Protector Type HMCP Type Amperes HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HKD HKD HLD HLD HND HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HJD HJD HKD HJD L600 HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HFD HJD HJD HJD HKD 7 15 15 30 30 50 50 100 100 150 150 150 150 250 400 400 600 600 600 7 7 7 15 15 30 30 50 50 70 100 100 150 150 150 150 400 400 600 3 7 7 7 15 30 30 30 50 50 70 100 100 150 150 150 250 250 400 Adj. Range 21 70 45 150 45 150 90 300 90 300 150 500 150 500 300 1000 300 1000 450 1500 450 1500 750 2500 750 2500 1250 2500 2000 4000 2000 4000 1800 6000 1800 6000 1800 6000 21 70 21 70 21 70 45 150 45 150 90 300 90 300 150 500 150 500 210 700 300 1000 300 1000 450 1500 750 2500 750 2500 750 2500 2000 4000 2000 4000 1800 6000 9 30 21 70 21 70 21 70 45 150 90 300 90 300 90 300 150 500 150 500 210 500 300 1000 300 1000 750 2500 750 2500 750 2500 1250 2500 1250 2500 2000 4000

1.5-7

Master TOC

Motor Protection
In line with 2005 NEC 430.6(A) circuit breaker, HMCP and fuse rating selections are based on full load currents for induction motors running at speeds normal for belted motors and motors with normal torque characteristics using data taken from NEC Table 130.250 (3-phase). Actual motor nameplate ratings shall be used for selecting motor running overload protection. Motors built special for low speeds, high torque characteristics, special starting conditions and applications will require other considerations as dened in the application section of the NEC. These additional considerations may require the use of a higher rated HMCP, or at least one with higher magnetic pickup settings. Circuit breaker, HMCP and fuse ampere rating selections are in line with maximum rules given in NEC 430.52 and Table 430.250. Based on known characteristics of Eatons Cutler-Hammer type breakers, specic units are recommended. The current ratings are no more than the maximum limits set by the NEC rules for motors with code letters F to V or without code letters. Motors with lower code letters will require further considerations. In general, these selections were based on: 1. Ambient Outside enclosure not more than 40C (104F). 2. Motor starting Infrequent starting, stopping or reversing. 3. Motor accelerating time 10 seconds or less. 4. Locked rotor Maximum 6 times motor FLA. Type HMCP motor circuit protector may not set at more than 1300% of the motor full-load current to comply with NEC 430.52. (Except for NEMA Design B energy high-efciency motors which can be set up to 1700%.) Circuit breaker selections are based on types with standard interrupting ratings. Higher interrupting rating types may be required to satisfy specic system application requirements. For motor full load currents of 208 and 200 volts, increase the corresponding 230-volt motor values by 10 and 15% respectively.

i ii 1 2 3 4 5 6 7

Time Delay Non-Time Delay Amperes

230 Volts, 3-Phase

1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50 60 75 100 125 150 200 1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50 60 75 100 125 150 200 1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50 60 75 100 125 150 200 3.6 5.2 6.8 9.6 15.2 22 28 42 54 68 80 104 130 154 192 248 312 360 480 1.8 2.6 3.4 4.8 7.6 11 14 21 27 34 40 52 65 77 96 124 156 180 240 1.4 2.1 2.7 3.9 6.1 9 11 17 22 27 32 41 52 62 77 99 125 144 192 10 10 15 20 30 40 50 80 100 125 150 200 250 300 350 450 600 700 1000 6 6 6 10 15 20 25 40 50 60 70 100 125 150 175 225 300 350 450 3 6 6 10 15 20 20 30 40 50 60 80 100 110 150 175 225 300 350 15 20 25 30 50 70 90 150 175 225 250 350 400 500 600 800 1000 1200 1600 6 10 15 15 25 35 45 70 90 110 125 175 200 150 300 400 500 600 800 6 10 10 15 20 30 35 60 70 90 100 125 175 200 250 300 400 450 600 15 15 15 20 30 50 60 90 100 125 150 150 200 225 300 400 500 600 700 15 15 15 15 15 25 35 45 50 70 70 100 110 125 150 175 225 250 350 15 15 15 15 15 20 25 40 50 60 60 80 100 125 150 175 200 225 300

460 Volts, 3-Phase

8 9 10 11 12 13 14 15 16 17 18 19 20 21

575 Volts, 3-Phase

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-8

Power Distribution Systems Reference Data

Motor Protective Device Data
Table 1.5-3. 60 Hz, Recommended Protective Setting for Induction Motors
hp Full Load Minimum Wire Size Amperes 75C Copper Ampacity (NEC) FLA at 125% FLA Size Amperes 20 20 30 30 50 85 100 20 20 20 20 30 50 50 .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) .75 (19.1) 1.00 (25.4) 1.00 (25.4) .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) .75 (19.1) Minimum Conduit Size, Inches (mm) THW THWN XHHN Fuse Size NEC 430-152 Maximum Amperes Time Delay Non-Time Delay

TOC

Index

June 2006
Sheet 0116

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Recommended Cutler-Hammer: Circuit Breaker Amperes Type 30 35 40 50 70 100 150 15 20 25 30 40 60 80 ED ED ED ED ED ED ED ED ED ED ED ED ED ED 2-Pole Device Not Available Motor Circuit Protector Type GMCP/HMCP Amperes Adjustable Range

115 Volts, Single-Phase

3/4 1 1-1/2 2 3 5 7-1/2 3/4 1 1-1/2 2 3 5 7-1/2 13.8 16 20 24 34 56 80 6.9 8 10 12 17 28 40 12 12 10 10 8 4 3 12 12 12 12 10 8 8 .50 (12.7) .50 (12.7) .50 (12.7) 25 30 35 45 50 60 80 110 175 250 25 25 30 40 60 90 125 2-Pole Device Not Available

.50 (12.7) 45 .50 (12.7) 60 .75 (19.1) 100 1.00 (25.4) 150 .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) .50 (12.7) 15 15 20 25 30 50 70

230 Volts, Single-Phase

Consult fuse manufacturers catalog for smaller fuse ratings. Types are for minimum interrupting capacity breakers. Ensure that the fault duty does not exceed breakers I.C.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0117

TOC

Index

Power Distribution Systems Reference Data

Chart of Short Circuit Currents for Transformers

1.5-9

Master TOC

Table 1.5-4. Secondary Short Circuit Current of Typical Power Transformers

Transformer Rating 3-Phase kVA and Impedance Percent 300 5% Maximum Short Circuit kVA Available from Primary System 50,000 100,000 150,000 250,000 500,000 Unlimited 500 5% 50,000 100,000 150,000 208 Volts, 3-Phase Rated Load Continuous Current, Amps 834 834 834 834 834 834 1388 1388 1388 Short Circuit Current rms Symmetrical Amps Transformer Alone 50% Motor Load Combined 240 Volts, 3-Phase Rated Load Continuous Current, Amps 722 722 722 722 722 722 Short Circuit Current rms Symmetrical Amps Transformer Alone 100% Motor Load Combined 480 Volts, 3-Phase Rated Load Continuous Current, Amps 361 361 361 361 361 361 601 601 601 601 601 601 902 902 902 902 902 902 Short Circuit Current rms Symmetrical Amps Transformer Alone 100% Motor Load Combined 600 Volts, 3-Phase Rated Load Continuous Current, Amps 289 289 289 289 289 289 481 481 481 481 481 481 722 722 722 722 722 722 962 962 962 962 962 962 Short Circuit Current rms Symmetrical Amps Transformer Alone 100% Motor Load Combined

i ii 1
6400 6700 6800 6800 6900 7000 9900 10,600 10,900 11,200 11,300 11,500 12,900 14,000 14,500 14,800 15,100 15,500 16,300 18,200 18,900 19,500 20,100 20,600 22,300 25,800 27,200 28,500 29,700 30,900 27,500 32,600 35,000 37,200 39,100 41,300 32,000 38,800 42,000 45,200 48,100 51,400 36,100 44,500 48,800 53,000 57,000 61,700 41,600 52,400 58,100 64,200 69,900 77,200

14,900 15,700 16,000 16,300 16,500 16,700 21,300 25,200 26,000 26,700 27,200 27,800 28,700 32,000 33,300 34,400 35,200 36,200 35,900 41,200 43,300 45,200 46,700 48,300 47,600 57,500 61,800 65,600 68,800 72,500

1700 1700 1700 1700 1700 1700 2800 2800 2800 2800 2800 2800 4200 4200 4200 4200 4200 4200 5600 5600 5600 5600 5600 5600 8300 8300 8300 8300 8300 8300

16,600 17,400 17,700 18,000 18,200 18,400

12,900 13,600 13,900 14,100 14,300 14,400 20,000 21,900 22,500 23,100 23,600 24,100 24,900 27,800 28,900 29,800 30,600 31,400 31,000 35,600 37,500 39,100 40,400 41,800 41,200 49,800 53,500 56,800 59,600 62,800

2900 2900 2900 2900 2900 2900 4800 4800 4800 4800 4800 4800 7200 7200 7200 7200 7200 7200 9800 9800 9800 9800 9800 9800 14,400 14,400 14,400 14,400 14,400 14,400

15,800 16,500 16,800 17,000 17,200 17,300 24,800 26,700 27,300 27,900 28,400 28,900 32,100 35,000 36,100 37,000 37,800 38,600

6400 6800 6900 7000 7100 7200 10,000 10,900 11,300 11,600 11,800 12,000 12,400 13,900 14,400 14,900 15,300 15,700 15,500 17,800 18,700 19,600 20,200 20,900 20,600 24,900 26,700 28,400 29,800 31,400 24,700 31,000 34,000 36,700 39,100 41,800 28,000 36,500 40,500 44,600 48,100 52,300 30,700 41,200 46,600 51,900 56,800 62,800 34,000 47,500 54,700 62,200 69,400 78,500

1400 1400 1400 1400 1400 1400 2400 2400 2400 2400 2400 2400 3600 3600 3600 3600 3600 3600 4800 4800 4800 4800 4800 4800 7200 7200 7200 7200 7200 7200 9600 9600 9600 9600 9600 9600 12,000 12,000 12,000 12,000 12,000 12,000 14,000 14,000 14,000 14,000 14,000 14,000 18,000 18,000 18,000 18,000 18,000 18,000

7800 8200 8300 8400 8500 8600 12,400 13,300 13,700 14,000 14,200 14,400 16,000 17,500 18,000 18,500 18,900 19,300 20,300 22,600 23,500 24,400 25,000 25,700

5200 5500 5600 5600 5700 5800 8000 8700 9000 9300 9400 9600 10,000 11,100 11,600 11,900 12,200 12,600 12,400 14,300 15,000 15,600 16,200 16,700 16,500 20,000 21,400 22,700 23,900 25,100 19,700 24,800 27,200 29,400 31,300 33,500 22,400 29,200 32,400 35,600 38,500 41,800 24,600 33,000 37,300 41,500 45,500 50,200 27,200 38,000 43,700 49,800 55,500 62,800

1200 1200 1200 1200 1200 1200 1900 1900 1900 1900 1900 1900 2900 2900 2900 2900 2900 2900 3900 3900 3900 3900 3900 3900 5800 5800 5800 5800 5800 5800 7800 7800 7800 7800 7800 7800 9600 9600 9600 9600 9600 9600 11,500 11,500 11,500 11,500 11,500 11,500 14,400 14,400 14,400 14,400 14,400 14,400

2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

25,900 1203 28,000 1203 28,800 1203 29,500 1203 30,000 1203 30,600 1203 32,900 1804 36,200 1804 37,500 1804 38,600 1804 39,400 1804 40,400 1804 41,500 2406 46,800 2406 48,900 2406 50,800 2406 52,300 2406 53,900 2406 55,900 3609 65,800 3609 70,100 3609 73,900 3609 77,100 3609 80,800 3609

250,000 1388 500,000 1388 Unlimited 1388 750 5.75% 50,000 100,000 150,000 2080 2080 2080

250,000 2080 500,000 2080 Unlimited 2080 1000 5.75% 50,000 100,000 150,000 2776 2776 2776

40,600 1203 45,200 1203 47,100 1203 48,700 1203 50,000 1203 51,400 1203 55,600 1804 64,200 1804 57,900 1804 71,200 1804 74,000 1804 77,200 1804 2406 2406 2406 2406 2406 2406 3008 3008 3008 3008 3008 3008 3609 3609 3609 3609 3609 3609 4511 4511 4511 4511 4511 4511

250,000 2776 500,000 2776 Unlimited 2776 1500 5.75% 50,000 100,000 150,000 4164 4164 4164

27,800 1444 32,100 1444 33,900 1444 35,600 1444 37,000 1444 38,600 1444 34,300 1924 40,600 1924 43,600 1924 46,300 1924 48,700 1924 51,400 1924 40,000 2405 48,500 2405 52,500 2405 56,600 2405 60,100 2405 64,300 2405 44,700 2886 55,200 2886 60,600 2886 65,900 2886 70,800 2886 76,800 2886 52,000 3608 65,500 3608 72,700 3608 80,200 3608 87,400 3608 96,500 3608

250,000 4164 500,000 4164 Unlimited 4164 2000 5.75% 50,000 100,000 150,000

250,000 500,000 Unlimited 2500 5.75% 50,000 100,000 150,000

250,000 500,000 Unlimited 3000 5.75% 50,000 100,000 150,000

250,000 500,000 Unlimited 3750 5.75% 50,000 100,000 150,000

250,000 500,000 Unlimited

Short circuit capacity values shown correspond to kVA and impedances shown in this table. For impedances other than these, short circuit currents are inversely proportional to impedance. The motors short circuit current contributions are computed on the basis of motor characteristics that will give four times normal current. For 208 volts, 50% motor load is assumed while for other voltages 100% motor load is assumed. For other percentages, the motor short circuit current will be in direct proportion.

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-10 Power Distribution Systems Reference Data

Transformer Full Load Amperes and Impedances
Table 1.5-5. Transformer Full-Load Current, 3-Phase, Self-Cooled Ratings
Voltage, Line-to-Line kVA 208 83.3 125 208 312 416 625 833 1388 2082 2776 4164 240 72.2 108 180 271 361 541 722 1203 1804 2406 3608 4811 480 36.1 54.1 90.2 135 180 271 361 601 902 1203 1804 2406 3007 3609 4511 600 28.9 43.3 72.2 108 144 217 289 481 722 962 1443 1925 2406 2887 3608 4811 2,400 7.22 10.8 18.0 27.1 36.1 54.1 72.2 120 180 241 361 481 601 722 902 1203 1804 2406 4,160 4.16 6.25 10.4 15.6 20.8 31.2 41.6 69.4 104 139 208 278 347 416 520 694 1041 1388 7,200 2.41 3.61 6.01 9.02 12.0 18.0 24.1 40.1 60.1 80.2 120 160 200 241 301 401 601 802 12,000 1.44 2.17 3.61 5.41 7.22 10.8 14.4 24.1 36.1 48.1 72.2 96.2 120 144 180 241 361 481 12,470 1.39 2.08 3.47 5.21 6.94 10.4 13.9 23.1 34.7 46.3 69.4 92.6 116 139 174 231 347 463 13,200 1.31 1.97 3.28 4.92 6.56 9.84 13.1 21.9 32.8 43.7 65.6 87.5 109 131 164 219 328 437

TOC

Index

June 2006
Sheet 0118

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

13,800 1.26 1.88 3.14 4.71 6.28 9.41 12.6 20.9 31.4 41.8 62.8 83.7 105 126 157 209 314 418

22,900 0.75 1.13 1.89 2.84 3.78 5.67 7.56 12.6 18.9 25.2 37.8 50.4 63.0 75.6 94.5 126 189 252

34,400 0.50 0.76 1.26 1.89 2.52 3.78 5.04 8.39 12.6 16.8 25.2 33.6 42.0 50.4 62.9 83.9 126 168

30 45 75 112-1/2 150 225 300 500 750 1000 1500 2000 2500 3000 3750 5000 7500 10,000

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0119

TOC

Index

Power Distribution Systems Reference Data

Impedances Data
Table 1.5-9. 600 Volt Primary Class NEMA Type TP-1 2002 Dry-Type Distribution Transformers
kVA %Z 6.66 7.32 5.97 5.91 5.95 5.11 7.55 7.65 3.47 6.71 6.10 6.72 4.13 4.96 8.07 7.79 5.83 5.87 2.23 5.25 3.45 3.25 3.81 3.89 4.99 5.65 3.57 %R 5.05 5.93 4.38 2.98 2.52 2.16 2.66 2.05 1.20 1.09 4.85 4.70 2.92 2.46 2.24 2.05 1.53 1.08 0.60 4.37 2.31 1.41 1.38 1.36 1.34 1.34 0.61 %X 4.34 4.29 4.05 5.10 5.39 4.62 7.06 7.37 3.25 6.62 3.69 4.89 2.92 4.31 7.75 7.51 5.62 5.77 2.14 2.91 2.57 2.93 3.55 3.64 4.81 5.49 3.51 X/R 0.86 0.72 0.92 1.71 2.14 2.14 2.65 3.60 2.71 6.07 0.76 1.04 1.00 1.75 3.46 3.66 3.67 5.34 3.57 0.67 1.11 2.08 2.57 2.68 3.59 4.10 5.75

1.5-11

Master TOC

Approximate Impedance Data

Table 1.5-6. Typical Impedances 3-Phase Transformers Liquid-Filled
kVA Liquid-Filled Network 37.5 45 50 75 112.5 150 225 300 500 750 1000 1500 2000 2500 3000 3750 5000 5.00 5.00 5.00 5.00 7.00 7.00 7.00 Padmount 3.4 3.2 2.4 3.3 3.4 4.6 5.75 5.75 5.75 5.75 5.75 6.50 6.50 6.50

Table 1.5-11. 600-Volt Primary Class Dry-Type Distribution Transformers

kVA %Z 7.93 3.70 3.42 5.20 5.60 4.50 4.90 5.90 6.20 6.40 7.10 5.50 6.30 6.50 5.20 4.60 3.70 4.60 6.50 6.20 7.20 6.30 5.50 4.10 2.30 2.90 2.90 3.70 4.30 4.10 5.30 3.30 4.50 %R 6.60 3.28 1.94 4.83 4.67 3.56 3.47 3.91 4.07 3.51 3.13 1.46 1.27 1.08 3.67 4.33 3.11 2.53 2.31 3.53 2.36 1.93 1.02 1.00 2.00 2.25 1.78 2.07 2.49 1.70 1.42 1.00 0.62 %X 4.40 1.71 2.81 1.92 3.10 2.76 3.46 4.42 4.68 5.35 6.37 5.30 6.17 6.41 3.69 1.54 2.00 3.84 6.08 5.09 6.80 6.00 5.40 3.98 1.14 1.83 2.29 3.07 3.51 3.73 5.11 3.14 4.46 X/R 0.67 0.52 1.45 0.40 0.66 0.78 1.00 1.13 1.15 1.52 2.03 3.63 4.87 5.93 1.01 0.36 0.64 1.52 2.63 1.44 2.89 3.10 5.30 3.98 0.57 0.81 1.29 1.49 1.41 2.19 3.59 3.14 7.19

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

150C Rise
15 30 45 75 112.5 150 225 300 500 750

150C Rise
3 6 9 15 30 45 75 112.5 150 225 300 500 750 1000

115C Rise
15 30 45 75 112.5 150 225 300 500

115C Rise
15 30 45 75 112.5 150 225 300 500 750

Values are typical. For guaranteed values, refer to transformer manufacturer.

80C Rise

Table 1.5-7. 15 kV Class Primary Oil Liquid-Filled Substation Transformers

kVA %Z 5.00 5.00 5.00 5.00 5.00 5.75 5.75 5.75 5.75 5.75 %R 1.71 1.88 1.84 1.35 1.50 1.41 1.33 1.12 0.93 0.86 %X 4.70 4.63 4.65 4.81 4.77 5.57 5.59 5.64 5.67 5.69 X/R 2.75 2.47 2.52 3.57 3.18 3.96 4.21 5.04 6.10 6.61

15 30 45 75 112.5 150 225 300

65C Rise
112.5 150 225 300 500 750 1000 1500 2000 2500

80C Rise
15 30 45 75 112.5 150 225 300 500

Table 1.5-10. 600 Volt Primary Class NEMA Type TP-1 Dry-Type Transformers
kVA 300 300 300 500 500 Temperature Rise 80 115 150 115 150 115 150 Impedance 3.16 at 100C 3.03 at 135C 7.06 at 170C 5.97 at 135C 6.04 at 170C 7.21 at 135C No Test

Table 1.5-8. 15 kV Class Primary Dry-Type Substation Transformers

kVA %Z 4.50 5.75 5.75 5.75 5.75 5.75 5.75 4.50 5.75 5.75 5.75 5.75 5.75 5.75 %R 2.87 2.66 2.47 2.16 1.87 1.93 1.74 1.93 1.44 1.28 0.93 0.87 0.66 0.56 %X 3.47 5.10 5.19 5.33 5.44 5.42 5.48 4.06 5.57 5.61 5.67 5.68 5.71 5.72 X/R 1.21 1.92 2.11 2.47 2.90 2.81 3.15 2.10 3.87 4.38 6.10 6.51 8.72 10.22

Note: K factor rated distribution dry-type transformers may have signicantly lower impedances.

150C Rise
300 500 750 1000 1500 2000 2500

750 750

80C Rise
300 500 750 1000 1500 2000 2500

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-12 Power Distribution Systems Reference Data

Transformer Losses

TOC

Index

June 2006
Sheet 0120

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Approximate Transformer Loss Data

Table 1.5-12. 15 kV Class Primary Oil Liquid-Filled Substation Transformers
kVA No Load Watts Loss 550 545 650 950 1200 1600 1800 3000 4000 4500 Full Load Watts Loss 2470 3360 4800 5000 8700 12,160 15,100 19,800 22,600 26,000

Table 1.5-14. 600-Volt Primary Class Dry-Type Distribution Transformers

kVA No Load Watts Loss 33 58 77 150 200 300 400 500 600 700 800 1700 2200 2800 150 200 300 400 500 600 700 800 1700 1500 200 300 300 400 600 700 800 1300 2200 Full Load Watts Loss 231 255 252 875 1600 1900 3000 4900 6700 8600 10,200 9000 11,700 13,600 700 1500 1700 2300 3100 5900 6000 6600 6800 9000 500 975 1100 1950 3400 3250 4000 4300 5300

Transformer Losses at Reduced Loads

Information on losses based on actual transformer test data can be obtained from the manufacturer. Transformer manufacturers provide no load watt losses and total watt losses in accordance with ANSI standards. The calculated difference between the no load losses and the total losses are typically described as the load losses. Although transformer coils are manufactured with either aluminum or copper conductors, the industry has sometimes referred to these load losses as the copper losses. Transformer losses for various loading can be estimated in the following manner. The no load watt losses of the transformer are due to magnetization and are present whenever the transformer is energized. The load watt losses are the difference between the no load watt losses and the full load watt losses. The load watt losses are proportional to I2R and can be estimated to vary with the transformer load by the square of the load current. For example, the approximate watts loss data for a 1000 kVA oil-lled substation transformer is shown in the table as having 1,800 watts no load losses and 15,100 watts full load losses, so the load losses are approximately 13,300 watts (15,100 1,800). The transformer losses can be calculated for various loads as follows. At 0% load: 1,800 watts At 50% load: 1,800 watts + (13,300)(.5)2 = 1,800 watts + 3,325 watts = 5,125 watts At 100% load: 1,800 watts + 13,300 watts = 15,100 watts At 110% load: 1,800 watts + (13,300)(1.1)2 = 1,800 watts + 16,093 watts = 17,893 watts Since transformer losses vary between designs and manufacturers, additional losses such as from cooling fans can be ignored for these approximations.
Note: 1 watthour = 3.413 Btu.

150C Rise
3 6 9 15 30 45 75 112.5 150 225 300 500 750 1000

65C Rise
112.5 150 225 300 500 750 1000 1500 2000 2500

Table 1.5-13. 15 kV Class Primary Dry-Type Substation Transformers

kVA No Load Watts Loss 1600 1900 2700 3400 4500 5700 7300 1800 2300 3400 4200 5900 6900 7200 Full Load Watts Loss 10,200 15,200 21,200 25,000 32,600 44,200 50,800 7600 9500 13,000 13,500 19,000 20,000 21,200

115C Rise
15 30 45 75 112.5 150 225 300 500 750

150C Rise
300 500 750 1000 1500 2000 2500

80C Rise
300 500 750 1000 1500 2000 2500

80C Rise
15 30 45 75 112.5 150 225 300 500

Table 1.5-15. 600-Volt Primary Class Dry-Type Distribution Transformers NEMA TP-1 2002
kVA No Load Losses in Watts N.L. 15 30 45 75 112.5 150 225 300 500 80 100 170 230 360 480 565 730 1350 Full Load Losses in Watts Total 822 1674 1885 2534 3290 3552 6783 7477 8031 TP-1% Efciency at 75C and 35% Load Minimum Required 97 97.5 97.7 98 98.2 98.3 98.5 98.6 98.7

Note: Loss and efciency data shown are based on transformers that meet NEMA optional standard TP-1 2002 for energy savings. NEMA TP-1 establishes minimum operating efciencies for each transformer size at reduced loading equal to 35% of the transformer base kVA. The 35% loading value in the NEMA standard reects eld studies which show that installed dry-type transformers are actually loaded far below base kVA most of the time.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0121

TOC

Index

Power Distribution Systems Reference Data

Power Equipment Losses and Enclosures/Knockout Dimensions

1.5-13

Master TOC

Power Equipment Losses

Table 1.5-16. Power Equipment Losses
Equipment Watts Loss 600 1400 2100 3700 500 750 840 600 1000 500 800 400 1000 1500 2400 3000 4700 200 500 750 3600 4500 4000 5000 7000 1200 300

Enclosures
The following are reproduced from NEMA 250. Table 1.5-17. Comparison of Specic Applications of Enclosures for Indoor Nonhazardous Locations
Provides a Degree of Protection Against the Following Environmental Conditions Incidental Contact with the Enclosed Equipment Falling Dirt Falling Liquids and Light Splashing Circulating Dust, Lint, Fibers, and Flyings Settling Airborne Dust, Lint, Fibers, and Flyings Hosedown and Splashing Water Oil and Coolant Seepage Oil or Coolant Spraying and Splashing Corrosive Agents Occasional Temporary Submersion Occasional Prolonged Submersion Type of Enclosures 1 2 4 4X 5 X X X X X X X X X X X X X X X X X X X X X X 6 X X X X X X X 6P X X X X X X X X X 12 X X X X X X 12K 13 X X X X X X X X X X X X X

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Medium Voltage Switchgear (Indoor, 5 and 15 kV)

1200 Ampere Breaker 2000 Ampere Breaker 3000 Ampere Breaker 4000 Ampere Breaker 600 Ampere Unfused Switch 1200 Ampere Unfused Switch 100 Ampere CL Fuses 400 Ampere Starter FVNR 800 Ampere Starter FVNR 600 Ampere Fused Switch 1200 Ampere Fused Switch 800 Ampere Breaker 1600 Ampere Breaker 2000 Ampere Breaker 3200 Ampere Breaker 4000 Ampere Breaker 5000 Ampere Breaker Fuse Limiters 800 Ampere CB Fuse Limiters 1600 Ampere CB Fuse Limiters 2000 Ampere CB Fuse Truck 3200 Ampere CB Fuse Truck 4000 Ampere CB Structures 3200 Ampere Structures 4000 Ampere Structures 5000 Ampere High Resistance Grounding

Medium Voltage Switchgear (Indoor, 5 and 15 kV)

Medium Voltage Starters (Indoor, 5 kV)

Low Voltage Switchgear (Indoor, 480 Volts)

These enclosures may be ventilated. These bers and ying are nonhazardous materials and are not considered the Class III type ignitable bers or combustible yings. For Class III type ignitable bers or combustible yings see the National Electrical Code, Article 500.

Table 1.5-18. Comparison of Specic Applications of Enclosures for Outdoor Nonhazardous Locations
Provides a Degree of Protection Against the Following Environmental Conditions Incidental Contact with the Enclosed Equipment Rain, Snow and Sleet Sleet Windblown Dust Hosedown Corrosive Agents Occasional Temporary Submersion Occasional Prolonged Submersion Type of Enclosures 3 3R 3S X X X X X X X X X 4 X X X X 4X X X X X X 6 X X X X X 6P X X X X X X X

Panelboards (Indoor, 480 Volts)

225 Ampere, 42 Circuit 800 Ampere 1200 Ampere 1350 Ampere 1600 Ampere 2000 Ampere 2500 Ampere 3200 Ampere 4000 Ampere 5000 Ampere NEMA Size 1 Starter NEMA Size 2 Starter NEMA Size 3 Starter NEMA Size 4 Starter NEMA Size 5 Starter Structures Adjustable Frequency Drives

These enclosures may be ventilated. External operating mechanisms are not required to be operable when the enclosure is ice covered. External operating mechanisms are operable when the enclosure is ice covered.

Low Voltage Busway (Indoor, Copper, 480 Volts)

44 per foot 60 per foot 66 per foot 72 per foot 91 per foot 103 per foot 144 per foot 182 per foot 203 per foot 39 56 92 124 244 200 > 96% efciency

Table 1.5-19. Comparison of Specic Applications of Enclosures for Indoor Hazardous Locations
Provides a Degree of Protection Against Atmospheres Typically Containing (For Complete Listing, See NFPA 497M) Acetylene Hydrogen, Manufactured Gas Diethyl Ether, Ethylene, Cyclopropane Gasoline, Hexane, Butane, Naphtha, Propane, Acetone, Toluene, Isoprene Metal Dust Carbon Black, Coal Dust, Coke Dust Flour, Starch, Grain Dust Fibers, Flyings Methane with or without Coal Dust Class Enclosure Types 7 and 8, Class I Groups A I I I I II II X B X C X D X Enclosure Type 9, Class II Groups E X F X G X X 10 X

Motor Control Centers (Indoor, 480 Volts)

II III MSHA

For Class III type ignitable bers or combustible yings see the National Electrical Code, Article 500. Due to the characteristics of the gas, vapor, or dust, a product suitable for one Class or Group may not be suitable for another Class or Group unless so marked on the product.

Adjustable Frequency Drives (Indoor, 480 Volts)

Note: If the installation is outdoors and/or additional protection is required by Tables 1.5-17 and 1.5-18, a combination-type enclosure is required.

Note: The information provided on power equipment losses is generic data intended to be used for sizing of HVAC equipment.

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-14 Power Distribution Systems Reference Data

Conductor Resistance, Reactance, Impedance

TOC

Index

June 2006
Sheet 0122

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Average Characteristics of 600-Volt Conductors Ohms per 1000 Feet (305 m)

The tables below are average characteristics based on data from IEEE Standard 141-1993. Values from different sources vary because of operating temperatures, wire stranding, insulation materials and thicknesses, overall diameters, random lay of multiple conductors in conduit, conductor spacing, and other divergences in materials, test conditions and calculation methods. These tables are for 600-volt 5 kV and 15 kV conductors, at an average temperature of 75C. Other parameters are listed in the notes. For medium voltage cables, differences among manufacturers are considerably greater because of the wider variations in insulation materials and thicknesses, shielding, jacketing, overall

diameters, and the like. Therefore, data for medium voltage cables should be obtained from the manufacturer of the cable to be used.

For interlocked armored cable, use magnetic conduit data for steel armor and non-magnetic conduit data for aluminum armor.
2 2

Application Notes
Resistance and reactance are phaseto-neutral values, based on 60 Hz ac, 3-phase, 4-wire distribution, in ohms per 100 feet (30 m) of circuit length (not total conductor lengths). s Based upon conductivity of 100% for copper, 61% for aluminum. s Based on conductor temperatures of 75C. Reactance values will have negligible variation with temperature. Resistance of both copper and aluminum conductors will be approximately 5% lower at 60C or 5% higher at 90C. Data shown in tables may be used without signicant error between 60C and 90C.
s

Z = X +R s For busway impedance data, see Section 21 of this catalog. s For PF (power factor) values less than 1.0, the effective impedance Z e is calculated from Z e = R PF + X sin (arc cos PF)
s

For copper cable data, resistance based on tinned copper at 60 Hz; 600V and 5 kV nonshielded cable based on varnished cambric insulation; 5 kV shielded and 15 kV cable based on neoprene insulation. s For aluminum cable data, cable is cross-linked polyethylene insulated.
s

Table 1.5-20. 60 Hz Impedance Data for 3-Phase Copper Cable Circuits, in Approximate Ohms per 1000 Feet (305 m) at 75C (a) Three Single Conductors
Wire Size, AWG or kcmil 8 8 (Solid) 6 6 (Solid) 4 4 (Solid) 2 1 1/0 2/0 3/0 4/0 250 300 350 400 450 500 600 750 In Magnetic Duct 600 V and 5 kV Nonshielded R X Z .811 .786 .510 .496 .321 .312 .202 .160 .128 .102 .0805 .0640 .0552 .0464 .0378 .0356 .0322 .0294 .0257 .0216 .0754 .0754 .0685 .0685 .0632 .0632 .0585 .0570 .0540 .0533 .0519 .0497 .0495 .0493 .0491 .0490 .0480 .0466 .0463 .0495 .814 .790 .515 .501 .327 .318 .210 .170 .139 .115 .0958 .0810 .0742 .0677 .0617 .0606 .0578 .0551 .0530 .0495 5 kV Shielded and 15 kV R X Z .811 .786 .510 .496 .321 .312 .202 .160 .128 .103 .0814 .0650 .0557 .0473 .0386 .0362 .0328 .0300 .0264 .0223 .0860 .0860 .0796 .0796 .0742 .0742 .0685 .0675 .0635 .0630 .0605 .0583 .0570 .0564 .0562 .0548 .0538 .0526 .0516 .0497 .816 .791 .516 .502 .329 .321 .214 .174 .143 .121 .101 .0929 .0797 .0736 .0681 .0657 .0630 .0505 .0580 .0545 In Nonmagnetic Duct 600 V and 5 kV Nonshielded R X Z .811 .786 .510 .496 .321 .312 .202 .160 .127 .101 .0766 .0633 .0541 .0451 .0368 .0342 .0304 .0276 .0237 .0194 .0603 .0603 .0548 .0548 .0506 .0506 .0467 .0456 .0432 .0426 .0415 .0398 .0396 .0394 .0393 .0392 .0384 .0373 .0371 .0356 .813 .788 .513 .499 .325 .316 .207 .166 .134 .110 .0871 .0748 .0670 .0599 .0536 .0520 .0490 .0464 .0440 .0405 5 kV Shielded and 15 kV R X Z .811 .786 .510 .496 .321 .312 .202 .160 .128 .102 .0805 .0640 .0547 .0460 .0375 .0348 .0312 .0284 .0246 .0203 .0688 .0688 .0636 .0636 .0594 .0594 .0547 .0540 .0507 .0504 .0484 .0466 .0456 .0451 .0450 .0438 .0430 .0421 .0412 .0396 .814 .789 .514 .500 .326 .318 .209 .169 .138 .114 .0939 .0792 .0712 .0644 .0586 .0559 .0531 .0508 .0479 .0445

Note: More tables on Page 1.5-15.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0123

TOC

Index

Power Distribution Systems Reference Data

Conductor Resistance, Reactance, Impedance

1.5-15

Master TOC

Table 1.5-21. 60 Hz Impedance Data for 3-Phase Copper Cable Circuits, in Approximate Ohms per 1000 Feet (305 m) at 75C (b) Three Conductor Cable
Wire Size, AWG or kcmil 8 8 (Solid) 6 6 (Solid) 4 4 (Solid) 2 1 1/0 2/0 3/0 4/0 250 300 350 400 450 500 600 750 In Magnetic Duct and Steel Interlocked Armor 600 V and 5 kV Nonshielded 5 kV Shielded and 15 kV R X Z R X Z .811 .786 .510 .496 .321 .312 .202 .160 .128 .102 .0805 .0640 .0552 .0464 .0378 .0356 .0322 .0294 .0257 .0216 .0577 .0577 .0525 .0525 .0483 .0483 .0448 .0436 .0414 .0407 .0397 .0381 .0379 .0377 .0373 .0371 .0361 .0349 .0343 .0326 .813 .788 .513 .499 .325 .316 .207 .166 .135 .110 .0898 .0745 .0670 .0598 .0539 .0514 .0484 .0456 .0429 .0391 .811 .786 .510 .496 .321 .312 .202 .160 .128 .103 .0814 .0650 .0557 .0473 .0386 .0362 .0328 .0300 .0264 .0223 .0658 .0658 .0610 .0610 .0568 .0508 .0524 .0516 .0486 .0482 .0463 .0446 .0436 .0431 .0427 .0415 .0404 .0394 .0382 .0364 .814 .789 .514 .500 .326 .317 .209 .168 .137 .114 .0936 .0788 .0707 .0640 .0576 .0551 .0520 .0495 .0464 .0427 In Nonmagnetic Duct and Aluminum Interlocked Armor 600 V and 5 kV Nonshielded 5 kV Shielded and 15 kV R X Z R X Z .811 .786 .510 .496 .321 .312 .202 .160 .127 .101 .0766 .0633 .0541 .0451 .0368 .0342 .0304 .0276 .0237 .0197 .0503 .0503 .0457 .0457 .0422 .0422 .0390 .0380 .0360 .0355 .0346 .0332 .0330 .0329 .0328 .0327 .0320 .0311 .0309 .0297 .812 .787 .512 .498 .324 .315 .206 .164 .132 .107 .0841 .0715 .0634 .0559 .0492 .0475 .0441 .0416 .0389 .0355 .811 .786 .510 .496 .321 .312 .202 .160 .128 .102 .0805 .0640 .0547 .0460 .0375 .0348 .0312 .0284 .0246 .0203 .0574 .0574 .0531 .0531 .0495 .0495 .0457 .0450 .0423 .0420 .0403 .0389 .0380 .0376 .0375 .0366 .0359 .0351 .0344 .0332 .813 .788 .513 .499 .325 .316 .207 .166 .135 .110 .090 .0749 .0666 .0596 .0530 .0505 .0476 .0453 .0422 .0389

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Table 1.5-22. 60 Hz Impedance Data for 3-Phase Aluminum Cable Circuits, in Approximate Ohms per 1000 Feet (305 m) at 90C (a) Three Single Conductors
Wire Size, AWG or kcmil 6 4 2 1 1/0 2/0 3/0 4/0 250 300 350 400 500 600 700 750 1000 In Magnetic Duct 600 V and 5 kV Nonshielded R X Z .847 .532 .335 .265 .210 .167 .133 .106 .0896 .0750 .0644 .0568 .0459 .0388 .0338 .0318 .0252 .053 .050 .046 .048 .043 .041 .040 .039 .0384 .0375 .0369 .0364 .0355 .0359 .0350 .0341 .0341 .849 .534 .338 .269 .214 .172 .139 .113 .0975 .0839 .0742 .0675 .0580 .0529 .0487 .0466 .0424 5 kV Shielded and 15 kV R X Z .532 .335 .265 .210 .167 .132 .105 .0892 .0746 .0640 .0563 .0453 .0381 .0332 .0310 .0243 .068 .063 .059 .056 .055 .053 .051 .0495 .0479 .0468 .0459 .0444 .0431 .0423 .0419 .0414 .536 .341 .271 .217 .176 .142 .117 .102 .0887 .0793 .0726 .0634 .0575 .0538 .0521 .0480 In Nonmagnetic Duct 600 V and 5 kV Nonshielded R X Z .847 .532 .335 .265 .210 .167 .133 .105 .0894 .0746 .0640 .0563 .0453 .0381 .0330 .0309 .0239 .042 .040 .037 .035 .034 .033 .037 .031 .0307 .0300 .0245 .0291 .0284 .0287 .0280 .0273 .0273 .848 .534 .337 .267 .213 .170 .137 .109 .0945 .0804 .0705 .0634 .0535 .0477 .0433 .0412 .0363 5 kV Shielded and 15 kV R X Z .532 .335 .265 .210 .167 .132 .105 .0891 .0744 .0638 .0560 .0450 .0377 .0326 .0304 .0234 .054 .050 .047 .045 .044 .042 .041 .0396 .0383 .0374 .0367 .0355 .0345 .0338 .0335 .0331 .535 .339 .269 .215 .173 .139 .113 .0975 .0837 .0740 .0700 .0573 .0511 .0470 .0452 .0405

Table 1.5-23. 60 Hz Impedance Data for 3-Phase Aluminum Cable Circuits, in Approximate Ohms per 1000 Feet (305 m) at 90C (b) Three Conductor Cable
Wire Size, AWG or kcmil 6 4 2 1 1/0 2/0 3/0 4/0 250 300 350 400 500 600 700 750 1000 In Magnetic Duct and Steel Interlocked Armor 600 V and 5 kV Nonshielded 5 kV Shielded and 15 kV R X Z R X Z .847 .532 .335 .265 .210 .167 .133 .106 .0896 .0750 .0644 .0568 .0459 .0388 .0338 .0318 .0252 .053 .050 .046 .048 .043 .041 .040 .039 .0384 .0375 .0369 .0364 .0355 .0359 .0350 .0341 .0341 .849 .534 .338 .269 .214 .172 .139 .113 .0975 .0839 .0742 .0675 .0580 .0529 .0487 .0466 .0424 .335 .265 .210 .167 .133 .105 .0895 .0748 .0643 .0564 .0457 .0386 .0335 .0315 .0248 .056 .053 .050 .049 .048 .045 .0436 .0424 .0418 .0411 .0399 .0390 .0381 .0379 .0368 .340 .270 .216 .174 .141 .114 .100 .0860 .0767 .0700 .0607 .0549 .0507 .0493 .0444 In Nonmagnetic Duct and Aluminum Interlocked Armor 600 V and 5 kV Nonshielded 5 kV Shielded and 15 kV R X Z R X Z .847 .532 .335 .265 .210 .167 .133 .105 .0894 .0746 .0640 .0563 .0453 .0381 .0330 .0309 .0239 .042 .040 .037 .035 .034 .033 .037 .031 .0307 .0300 .0245 .0291 .0284 .0287 .0280 .0273 .0273 .848 .534 .337 .267 .213 .170 .137 .109 .0945 .0804 .0705 .0634 .0535 .0477 .0433 .0412 .0363 .335 .265 .210 .167 .132 .105 .0893 .0745 .0640 .0561 .0452 .0380 .0328 .0307 .0237 .045 .042 .040 .039 .038 .036 .0349 .0340 .0334 .0329 .0319 .0312 .0305 .0303 .0294 .338 .268 .214 .171 .138 .111 .0959 .0819 .0722 .0650 .0553 .0492 .0448 .0431 .0378

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-16 Power Distribution Systems Reference Data

Conductor Ampacities

TOC

Index

June 2006
Sheet 0124

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Current Carrying Capacities of Copper and Aluminum and Copper-Clad Aluminum Conductors From National Electrical Code (NEC), 2005 Edition (NFPA70-2005)
Table 1.5-24. Allowable Ampacities of Insulated Conductors Rated 0 2000 Volts, 60C to 90C (140F to 194F). Not more than three current-carrying conductors in raceway, cable or earth (directly buried), based on ambient temperature of 30C (86F)
Size AWG or kcmil Temperature Rating of Conductor (See Table 310.16) 60C (140F) Types TW, UF RHW, THHW, THW, THWN, XHHW, USE, ZW TBS, SA, SIS, FEP, FEPB, MI, RHH, RHW-2, THHN, THHW, THW-2, THWN-2, USE-2, XHH, XHHW, XHHW-2, ZW-2 75C (167F) 90C (194F) 60C (140F) Types TW, UF RHW, THHW, THW, THWN, XHHW, USE TBS, SA, SIS, THHN, THHW, THW-2, THWN-2, RHH, RHW-2, USE-2, XHH, XHHW, XHHW-2, ZW-2 75C (167F) 90C (194F) Size AWG or kcmil

Copper 18 16 14 12 10 8 6 4 3 2 1 1/0 2/0 3/0 4/0 250 300 350 400 500 600 700 750 800 900 1000 1250 1500 1750 2000 20 25 30 40 55 70 85 95 110 125 145 165 195 215 240 260 280 320 355 385 400 410 435 455 495 520 545 560 20 25 35 50 65 85 100 115 130 150 175 200 230 255 285 310 335 380 420 460 475 490 520 545 590 625 650 665 14 18 25 30 40 55 75 95 110 130 150 170 195 225 260 290 320 350 380 430 475 520 535 555 585 615 665 705 735 750

Aluminum or Copper-Clad Aluminum 20 25 30 40 55 65 75 85 100 115 130 150 170 190 210 225 260 285 310 320 330 355 375 405 435 455 470 20 30 40 50 65 75 90 100 120 135 155 180 205 230 250 270 310 340 375 385 395 425 445 485 520 545 560 25 35 45 60 75 85 100 115 135 150 175 205 230 255 280 305 350 385 420 435 450 480 500 545 585 615 630 12 10 8 6 4 3 2 1 1/0 2/0 3/0 4/0 250 300 350 400 500 600 700 750 800 900 1000 1250 1500 1750 2000 Ambient Temperature F 1.04 1.00 .96 .91 .87 .82 .76 .71 .58 .41 70 77 78 86 87 95 96 104 105 113 114 122 123 131 132 140 141 158 159 176

Correction Factors
Ambient Temperature C 21 25 26 30 31 35 36 40 41 45 46 50 51 55 56 60 61 70 71 80 For ambient temperatures other than 30C (86F), multiply the allowable ampacities shown above by the appropriate factor shown below. 1.08 1.00 .91 .82 .71 .58 .41 1.05 1.00 .94 .88 .82 .75 .67 .58 .33 1.04 1.00 .96 .91 .87 .82 .76 .71 .58 .41 1.08 1.00 .91 .82 .71 .58 .41 1.05 1.00 .94 .88 .82 .75 .67 .58 .33

See NEC Section 240.4 (D).

Note: For complete details of using Table 1.5-24, see NEC Article 310 in its entirety.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0125

TOC

Index

Power Distribution Systems Reference Data

Conductor Ampacities
(1) General. For explanation of type letters used in tables and for recognized sizes of conductors for the various conductor insulations, see 310.13. For installation requirements, see 310.1 through 310.10 and the various articles of this Code. For exible cords, see Table 400.4, Table 400.5(A), and Table 400.5(B). (2) Adjustment Factors. (a) More Than Three Current-Carrying Conductors in a Raceway or Cable. Where the number of currentcarrying conductors in a raceway or cable exceeds three, or where single conductors or multiconductor cables are stacked or bundled longer than 600 mm (24 in.) without maintaining spacing and are not installed in raceways, the allowable ampacity of each conductor shall be reduced as shown in Table 1.5-25. Each current-carrying conductor of a paralleled set of conductors shall be counted as a current-carrying conductor.
Note: FPN No. 1: See Annex B, Table B.310.11, for adjustment factors for more than three current-carrying conductors in a raceway or cable with load diversity. Note: FPN No. 2: See 366.23(A) for correction factors for conductors in sheet metal auxiliary gutters and 376.22 for correction factors for conductors in metal wireways.

1.5-17

Master TOC

Ampacities for Conductors Rated 0 2000 Volts (Excerpts from NEC 310-15)
(A) General.
(1) Tables or Engineering Supervision. Ampacities for conductors shall be permitted to be determined by tables as provided in 310.15(B) or under engineering supervision, as provided in 310.15(C).
Note: FPN No. 1: Ampacities provided by this section do not take voltage drop into consideration. See 210.19(A), FPN No. 4, for branch circuits and 215.2(A), FPN No. 2, for feeders. Note: FPN No. 2: For the allowable ampacities of Type MTW wire, see Table 13.5.1 in NFPA 79-2002, Electrical Standard for Industrial Machinery.

(1) Each cable has not more than three current-carrying conductors. (2) The conductors are 12 AWG copper. (3) Not more than 20 current-carrying conductors are bundled, stacked, or supported on bridle rings. A 60 percent adjustment factor shall be applied where the current-carrying conductors in these cables that are stacked or bundled longer than 24 inches (600 mm) without maintaining spacing exceeds 20. (b) More Than One Conduit, Tube, or Raceway. Spacing between conduits, tubing, or raceways shall be maintained.

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Table 1.5-25. NEC (2005) Table 310.15(B)(2)(a) Adjustment Factors for More than Three CurrentCarrying Conductors in a Raceway or Cable
Number of Current-Carrying Conductors 46 79 10 20 21 30 31 40 41 and Above Percent of Values in Tables as Adjusted for Ambient Temperature if Necessary 80 70 50 45 40 35

(2) Selection of Ampacity. Where more than one calculated or tabulated ampacity could apply for a given circuit length, the lowest value shall be used. Exception: Where two different ampacities apply to adjacent portions of a circuit, the higher ampacity shall be permitted to be used beyond the point of transition, a distance equal to 10 feet (3.0 m) or 10 percent of the circuit length gured at the higher ampacity, whichever is less.
Note: FPN: See 110.14(C) for conductor temperature limitations due to termination provisions.

(B) Tables. Ampacities for conductors rated 0 to 2000 volts shall be as specied in the Allowable Ampacity Table 310.16 through Table 310.19, and Ampacity Table 310.20 and Table 310.21 as modied by (B)(1) through (B)(6).
Note: FPN: Table 310.16 through Table 310.19 are application tables for use in determining conductor sizes on loads calculated in accordance with Article 220. Allowable ampacities result from consideration of one or more of the following:

Exception No. 1: Where conductors of different systems, as provided in 300.3, are installed in a common raceway or cable, the derating factors shown in Table 1.5-25 shall apply only to the number of power and lighting conductors (Articles 210, 215, 220 and 230). Exception No. 2: For conductors installed in cable trays, the provisions of 392.11 shall apply. Exception No. 3: Derating factors shall not apply to conductors in nipples having a length not exceeding 24 inches (600 mm). Exception No. 4: Derating factors shall not apply to underground conductors entering or leaving an outdoor trench if those conductors have physical protection in the form of rigid metal conduit, intermediate metal conduit, or rigid nonmetallic conduit having a length not exceeding 3.05 m (10 ft) and if the number of conductors does not exceed four. Exception No. 5: Adjustment factors shall not apply to Type AC cable or to Type MC cable without an overall outer jacket under the following conditions:
For more information visit: www.EatonElectrical.com

(3) Bare or Covered Conductors. Where bare or covered conductors are used with insulated conductors, their allowable ampacities shall be limited to those permitted for the adjacent insulated conductors. (4) Neutral Conductor. (a) A neutral conductor that carries only the unbalanced current from other conductors of the same circuit shall not be required to be counted when applying the provisions of 310.15(B)(2)(a). (b) In a 3-wire circuit consisting of 2-phase wires and the neutral of a 4-wire, 3-phase, wye-connected system, a common conductor carries approximately the same current as the line-to-neutral load currents of the other conductors and shall be counted when applying the provisions of 310.15(B)(2)(a). (c) On a 4-wire, 3-phase wye circuit where the major portion of the load consists of nonlinear loads, harmonic currents are present in the neutral conductor; the neutral shall therefore be considered a currentcarrying conductor. (5) Grounding or Bonding Conductor. A grounding or bonding conductor shall not be counted when applying the provisions of 310.15(B)(2)(a).

(1) Temperature compatibility with connected equipment, especially the connection points. (2) Coordination with circuit and system overcurrent protection. (3) Compliance with the requirements of product listings or certications. See 110.3(B). (4) Preservation of the safety benets of established industry practices and standardized procedures.

CA08104001E

1.5-18 Power Distribution Systems Reference Data

Formulas and Terms
Table 1.5-26. Formulas for Determining Amperes, hp, kW and kVA
To Find Amperes (l) When Horsepower is Known Amperes (l) When Kilowatts is Known Amperes (l) When kVA is Known Kilowatts kVA Horsepower (Output) Direct Current hp 746 E % eff kW 1000 E IE 1000 I E % eff 746 Alternating Current Single-Phase hp 746 E % eff pf kW 1000 E pf kVA 1000 E l E pf 1000 IE 1000 2-Phase 4-Wire hp 746 2 E % eff pf kW 1000 2 E pf kVA 1000 2E l E 2 pf 1000 IE2 1000

TOC

Index

June 2006
Sheet 0126

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11

3-Phase hp 746 3 E % eff pf kW 1000 3 E % pf kVA1000 3E l E 3 pf 1000 IE 3 1000

I E 2 % eff pf I E % eff pf I E 3 % eff pf 746 746 746 For 2-phase, 3-wire circuits the current in the common conductor is 2 times that in either of the two other conductors.

Note: Units of measurement and denitions for E (volts), I (amperes), and other abbreviations are given below under Common Electrical Terms.

Common Electrical Terms

Ampere (l) Volt (E) Ohm (R) = unit of current or rate of ow of electricity = unit of electromotive force = unit of resistance E Ohms law: I = (dc or 100% pf) R = 1,000,000 ohms = unit of apparent power = E l (single-phase) = El 3

How to Compute Power Factor

Watts Determining Watts pf = --------------------------------------------Volts Amperes

1. 1. From watthour meter. Watts = rpm of disc x 60 x Kh Where Kh is meter constant printed on face or nameplate of meter. If metering transformers are used, above must be multiplied by the transformer ratios. 2. Directly from wattmeter reading. Where: Volts = line-to-line voltage as measured by voltmeter. Amperes = current measured in line wire (not neutral) by ammeter. Table 1.5-27. Temperature Conversion
(F to C) (C to F) C -15 F 5 C 25 F 77 C 65 F 149 -10 14 30 86 -5 23 C = 5/9 (F-32) F = 9/5(C)+32 0 32 5 41 10 50 15 59 20 68 60 140 100 212

Megohm Volt Amperes (VA)

Kilovolt Amperes (kVA) = 1000 volt-amperes Watt (W) = unit of true power = VA pf = .00134 hp = 1000 watts = ratio of true to apparent power W kW = -------- ----------VA kVA = unit of electrical work = one watt for one hour = 3.413 Btu = 2,655 foot. lbs. = 1000 watthours = measure of time rate of doing work = equivalent of raising 33,000 lbs. one foot. in one minute = 746 watts = ratio of maximum demand to the total connected load = ratio of the sum of individual maximum demands of the various subdivisions of a system to the maximum demand of the whole system = ratio of the average load over a designated period of time to the peak load occurring in that period

Kilowatt (kW)

12 13 14 15 16 17 18 19 20 21

Power Factor (pf)

Watthour (Wh)

Kilowatt-hour (kWh) Horsepower (hp)

35 40 45 95 104 113

50 55 122 131 90 95 194 203

70 75 80 85 158 167 176 185

Demand Factor Diversity Factor

Load Factor

1 Inch = 2.54 centimeters 1 Kilogram = 2.20 lbs. 1 Square Inch = 1,273,200 circular mills 1 Circular Mill = .785 square mil 1 Btu = 778 foot. lbs. = 252 calories 1 Year = 8,760 hours

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0127

TOC

Index

Power Distribution Systems Reference Data

Seismic Requirements

1.5-19

Master TOC

Seismic Requirements
General
Starting more than 15 years ago, Eaton embarked on a comprehensive program centered around designing and building electrical distribution and control equipment capable of meeting and exceeding the seismic load requirements of the Uniform Building Code (UBC ) and California Building Code (CBC). The entire program has been updated to also meet the Year 2003 International Building Code (IBC) unied seismic requirements. These codes emphasize building design requirements. Electrical equipment and distribution system components are considered attachments to the building. The equipment is acceptable if it can withstand the seismic event and perform its function immediately afterwards. A cooperative effort with the equipment user, the building designer and the equipment installer ensures that the equipment is correctly mounted to a foundation that can withstand the effects of an earthquake. Cutler-Hammer electrical distribution and power control equipment has been tested and seismically proven for requirements exceeding the UBC, CBC and the IBC. Over one hundred different assemblies representing all product lines have been successfully tested and veried to seismic levels higher than the maximum seismic requirements specied in the UBC, CBC and the IBC. The equipment maintained structural integrity and demonstrated the ability to function before and immediately after the seismic tests. A technical paper, Earthquake Requirements and Cutler-Hammer Distribution and Control Equipment Seismic Capabilities (SA.125.01.S.E), provides a detailed explanation of the applicable seismic codes and the Cutler-Hammer program to qualify equipment. The paper may be found at www.EatonElectrical.com. Type in SA12501SE in document search.

i ii 1 2 3 4 5
Uniform Building Code Seismic Zones
0 1 2A 2B 3 4 Those areas within Zone 3 determined by the proximity to certain major faults

6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

No damage

Minor damage

Moderate damage

Moderate damage

Major damage

Figure 1.5-1. UBC Seismic Zone Map of the United States

Uniform Building Code (UBC)

The 1997 Uniform Building Code, Chapter 16 of Division IV-Earthquake Design, requires that structures and portions of structures shall be designed to withstand the seismic ground motion specied in the codes. Section 1632 of the codes Lateral Force on Elements of Structures, Nonstructural Components and Equipment Supported by Structures, and under subsection Section 1632.1: General, states that: Elements of structures and their attachments, permanent nonstructural components and their attachments, and the attachments for permanent equipment supported by a structure shall be designed to resist the total design seismic forces prescribed in Section 1632.2. Section 1632.2, Design for Total Lateral Force, species that the total design lateral static seismic force, Fp, is dened as (see equation 32-1 in code, Page 2-18): F p = 4.0 C a I p W p

States is shown in Figure 1.5-1 (Figure 16-3 of the UBC, Chapter 16). Ca is taken equal to the maximum of 0.44 x 1.5 = 0.66. Ip: Is the Seismic Importance Factor (Table 16-K, page 2-30). It is taken as maximum and equal to 1.5. Wp: Is the Equipment Operating Weight. Therefore, the maximum theoretical static seismic loads (including all the conservatism possible) are: F p = 4.0 ( .44 1.5 ) 1.5 W p The codes state that the design lateral accelerations and resultant loads, determined above, are static loads to be distributed in proportion to the mass distribution of the element or component. Therefore, assuming a uniformly distributed mass, the static loads computed in the above formula are imposed at the C.G. or at conservatively one half the height of the equipment from its base. The complete Response Spectrum Curve starts at 0.33g at 1.0 Hz, linearly increases to 2.15g at 2.15 Hz (Ts ). The peak spectral accelerations then covers a wide band of frequencies up to 11 Hz (To) then gradually decreases to 0.86 g (ZPA) at 33 Hz. This curve represents the complete 1997 UBC Design Response Spectrum.

Where:
Ca: Is the Seismic Coefcient for Zone 4, Table 16-Q. It is equal to a maximum of 0.44 Na where Na is Near Source Factor and is equal to a maximum of 1.5 (see Table 16-S, page 2-35). The Seismic Zone Map of the United
CA08104001E For more information visit: www.EatonElectrical.com

1.5-20 Power Distribution Systems Reference Data

Seismic Requirements

TOC

Index

June 2006
Sheet 0128

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

California Building Code

California Building Code adopted the 1997 UBC as the CBC-Title 24. The seismic requirements are basically the same as described in the UBC. When considering the maximum seismic requirements, the UBC and CBC are basically identical. Again, as in the UBC, the Response Spectrum Curve starts at 0.33g at 1.0 Hz, linearly increases to 2.15g at 2.15 Hz (Ts). The peak spectral accelerations then cover a wide band of frequencies up to 11 Hz (To) then gradually decreases to 0.86g (ZPA) at 33 Hz.

Year 2003 International Building Code (IBC)

On December 9, 1994, the International Code Council (ICC) was established as a nonprot organization dedicated to developing a single set of comprehensive and coordinated national codes. The ICC founders the Building Ofcials and Code Administrators (BOCA), the International Conference of Building Ofcials (ICBO), and the Southern Building Code Congress International (SBCCI ) created the ICC in response to technical disparities among the three nationally recognized model codes now in use in the U.S. The ICC offers a single, complete set of construction codes without regional limitations the International IBC Codes. According to Chapter 16, Structure Design, the seismic requirements of electrical equipment in buildings may be computed in two steps. The rst step is to determine the maximum ground motion to be considered at the site. The second step is to evaluate the equipment mounting and attachments inside the building or structure. The two sets are then evaluated to determine appropriate seismic test requirements. The ground motion, the in-structure seismic requirements of the equipment, and the seismic response spectrum requirements are discussed below.

A. Ground Motion
According to the code, the rst and most important step in the process is to determine the Maximum Considered Earthquake Spectral Response Acceleration at short periods of 0.2 seconds (SS) and at a period of 1.0 second (S1). These values are determined from a set of 24 Spectral Acceleration Maps which include numerous contour lines indicating the severity of the earthquake requirements at a particular location in the country.

ANSI C37.81
The seismic requirements for Class 1E switchgear in nuclear power plants are dened in ANSI C37.81. Eaton elected to test the equipment to 2/3 of the nuclear requirements.

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0129

TOC

Index

Power Distribution Systems Reference Data

Seismic Requirements

1.5-21

Master TOC

The maps indicate low to moderate seismic requirements for the entire country, with the exception of two particular areas; the West Coast (the State of California) and the Midwest (the New Madrid areas). Areas with the seismic requirements at the New Madrid are approximately 40% higher than the maximum requirements of the West Coast. The Design Response Spectrum/ Spectral accelerations are equal to 0.68g at zero period (ZPA), increase linearly to a peak acceleration of 1.7g at 0.146 seconds (or 6.9 Hz) and stay constant to 0.73 seconds (or 1.37 Hz) then gradually decrease to 1.24g at 1 second (or 1 Hz).

i ii 1 2 3 4 5
Seismic Zones
0 1 2A 2B 3 4 Those areas within Zone 3 determined by the proximity to certain major faults

B. ASCE7 Section 9.6.1.3 Seismic Forces

The code provides a formula for computing the seismic requirements of electrical and mechanical equipment inside a building or a structure. The formula is designed for evaluating the equipment attachment to the equipment foundations. The seismic loads are dened as: F p = .4a p S DS W p ( 1 + 2 Z h ) ( R p I p ) Figure 1.5-2. Bellcore Earthquake Zone Map The following parameters produce the maximum required force:
s s

6 7 8 9
Bellcore Requirements
The Bellcore Generic Requirements (GR-63-CORE, Issue 1, dated 1995) for the Network Equipment-Building System (NEBS) (Reference 10), and the Physical Protection Section 5.4 of the code includes a map of the seismic zones (Figure 1.5-2), as well as a proposed Response Spectrum Curve for testing communication equipment. Descriptions of the test requirements and test levels of equipment are also included.

No damage

Minor damage

Moderate damage

Moderate damage

Major damage

Where:
Fp : Seismic design force imposed at the components C.G. and distributed relative to component mass distribution. Component amplication factor that varies from 1.00 to 2.50.

10 11 12 13 14 15 16 17 18 19 20 21

ap :

s s s

SDS: Spectral acceleration, short period, as determined in the previous section. Wp: Component operating weight. Rp: Component response modication factor that varies from 1.0 to 5.0. Ip : Z: Component importance factor that is either 1.0 or 1.5. Highest point of equipment in a structure relative to grade elevation. Average roof height of structure relative to grade elevation.

Z is taken equal to H (equipment on roof). Ip is taken equal to 1.5. Ap is taken equal to 2.5. Rp is taken equal to 2.5. SDS is equal to 1.7g as computed in previous section.

The acceleration at C.G. of equipment is then computed equal to: Acceleration = 0.4 x 2.5 x 1.7g (1 + 2) / (2.5/1.5) = 3.06g For equipment on grade, the acceleration at C.G. is then computed equal to: Acceleration = 0.4 x 2.5 x 1.7g (1 + 0) / (2.5 /1.5) = 1.02g The base forces associated with the static loads at the C.G. of the equipment could be computed as 3.06/1.5 = 2.04g. Finally ASCE7 Section 9.6.1.3 provides for FP is not required to be taken as greater than FP = 1.6 SDS IP WP When IP = 1.5

h:

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-22 Power Distribution Systems Reference Data

Seismic Requirements

TOC

Index

June 2006
Sheet 0130

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14

Final Combined Requirements

Acceleration (g peak)

To better compare all seismic levels and determine the nal envelope seismic requirements, the UBC, CBC, Y2K IBC for California, Y2K IBC for New Madrid area, and Bellcore nal seismic requirements are plotted in Figure 1.5-3. All curves are plotted at 5% damping. An envelopment of the seismic levels in the frequency range of 3.2 Hz to 100 Hz is also shown. This level is taken as Cutler-Hammer generic seismic test requirements for all certications. Eaton performed additional seismic test runs on the equipment at approximately 120% of the generic enveloping seismic requirements (see Figure 1.5-4). The testing is designed to establish additional margin and prepare for future changes in the codes.

10 9 8 7 6 5 4 3

IBC, New Madrid CH Seismic Envelope IBC, California

Equiv. Bellcore
2

1.0 .9 .8 .7 .6 .5 .4 .3

UBC and CBC

.2

.1 1 2 3 4 5 6 7 8 9 10 10 2 3 4 5

Frequency Hz

6 7 8 9 10 100

6 7 8 9 10 1000

Figure 1.5-3. Required Response Spectrum Curve

10 9 8 7 6 5 4 3

Acceleration (g peak)

120% of CH Seismic Envelope CH Seismic Envelope

1.0 .9 .8 .7 .6 .5 .4 .3

.2

.1

15 16 17 18 19 20 21

6 7 8 9 10 10

Frequency Hz

6 7 8 9 10 100

6 7 8 9 10 1000

Figure 1.5-4. Eaton Test Required Response Spectrum Curve

For more information visit: www.EatonElectrical.com

CA08104001E

June 2006
Sheet 0131

TOC

Index

Power Distribution Systems Reference Data

Seismic Requirements

1.5-23

Master TOC

Product Specic Test Summaries

Table 1.5-28. Distribution Equipment Qualied for Applications through Seismic Zone 4
Cutler-Hammer Equipment Low Voltage Panelboards Pow-R-Line C 1a, 2a, 3a, 4, 5p, F16, Column Type Low Voltage Switchboards Pow-R-Line C Pow-R-Line i Multimeter Instant IFS Low Voltage Deadfront Switchboards Motor Control Centers Advantage Series 2100 Freedom 2100 Low Voltage Busway Pow-R-Way and Associated Fittings Pow-R-Way III and Associated Fittings Transfer Switch Equipment Low Voltage Metal-Enclosed Switchgear Type DS II Magnum DS-VSR Size 5 Vacuum Starter Network Protectors Submersible Type CMD and Type CM-22 Wall Mounted Dry-Type Distribution Transformers Types EP, EPT, DS, DT3 Substation Transformers Dry-Type Liquid Unitized Dry-Type Power Centers 750 kVA Maximum Excitation Control Assemblies MGR, PRX-400B, WDR1000, WDR2000, WTA-300B ECS 2100 Metal-Enclosed Load Interrupter Switchgear Type WLI 5, 15 and 38 kV Type WVB 5 and 15 kV Type MVS 5 and 15 kV Medium Voltage Metal-Clad Switchgear Type VacClad-W Metal-Enclosed Non-Segregated Phase Bus 600 V, 5 and 15 kV Medium Voltage Control AMPGARD Vacuum Replacement Circuit Breakers DHP-VR for DHP Switchgear Loadcenters Heavy Duty Safety Switches Enclosed Control

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13
Figure 1.5-5. Sample Seismic Certicate
Cutler-Hammer is a federally registered trademark of Eaton Corporation. National Electrical Code and NEC are registered trademarks of the National Fire Protection Association, Quincy, Mass. NEMA is the registered trademark and service mark of the National Electrical Manufacturers Association. UL and CUL are federally registered trademarks of Underwriters Laboratories Inc. Uniform Building Code (UBC) is a trademark of the International Conference or Building Ofcials (ICBO). BOCA is a registered trademark of Building Ofcials and Code Administrators International, Inc. SBCCI is a registered trademark of Southern Building Code Congress International.

14 15 16 17 18 19

Equipment Seismic Label

20 21

CA08104001E

For more information visit: www.EatonElectrical.com

1.5-24 Power Distribution Systems

TOC Index

June 2006
Sheet 0132

Master TOC

i ii 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

This page intentionally left blank.

For more information visit: www.EatonElectrical.com

CA08104001E