Scribd
Upload
40 views

Setting Totalizer

The document provides instructions for configuring totalizers 1-3 using the easy setup wizard of an instrument. It describes selecting the totalizer menu from the easy setup wizard, then configuring parameters like channel, unit, failure option, and start/stop for totalizer 1. The instructions note totalizers 4-6 require configuration via a different menu. It also indicates totalizers 2 and 3 can be configured similarly once totalizer 1 is complete.

Uploaded by

mbdonek5252
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
40 views

Setting Totalizer

The document provides instructions for configuring totalizers 1-3 using the easy setup wizard of an instrument. It describes selecting the totalizer menu from the easy setup wizard, then configuring parameters like channel, unit, failure option, and start/stop for totalizer 1. The instructions note totalizers 4-6 require configuration via a different menu. It also indicates totalizers 2 and 3 can be configured similarly once totalizer 1 is complete.

Uploaded by

mbdonek5252
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Setting Totalizer

Configuration of Totalizer 1 – 3 is shown below, Totalizer 4 – 6 cannot be configured by


Easy setup wizard. To configure Totalizer 4 – 6 , see Detailed setup menu [IM01U10S01 -
*page 547]

Under “Specialist” Operation Level,

1. Press [INC] until [Easy setup wizard] is selected.


2. Press [SET] to enter the menu [Easy setup wizard].
Menu [Install cfg] is preselected.
3. Press [INC] until [Ttl] is selected.
4. Press [SET] to enter the menu [Ttl].
Menu [Ttl1] is preselected.
5. Press [SET] to enter the menu [Ttl1].
[Setting upload] runs automatically and will be marked with a * after
completion.
Parameter [Channel] is preselected.
6. Press [SET] to enter the selection [Channel].
7. Press [INC] until the desired variable is selected and press [SET] to choose the
selection.
The chosen value flashes.
8. Press [SET] to confirm.
9. Press [SET] to go back to the menu [Ttl1].
Parameter [Channel] is marked with a * after completion.
Parameter [Unit] is preselected.
10. Press [SET] to enter the selection [Unit].
11. Press [INC] until the required unit is selected and press [SET] to choose the
selection.
The chosen value flashes.
12. Press [SET] to confirm.
13. Press [SET] to go back to the menu [Ttl1].
Parameter [Unit] is marked with a * after completion.
Parameter [Fail opt] is preselected.
14. Press [SET] to enter the selection [Fail opt].
15. Press [INC] to select [Run], [Hold] or [Last valid val].
16. Press [SET] to choose the selection.
The chosen value flashes.
17. Press [SET] to confirm.
18. Press [SET] to go back to the menu [Ttl1].
TN-P-20210524-01
17
Parameter [Fail opt] is marked with a * after completion.
Parameter [Start/Stop] is preselected.
19. Press [SET] to enter the selection [Start/Stop].
20. Press [INC] to select [Stop] or [Start].
21. Press [SET] to choose the selection.
The chosen value flashes.
22. Press [SET] to confirm.
23. Press [SET] to go back to the menu [Ttl1].
Parameter [Start/Stop] is marked with a * after completion.
Parameter [Setting download] is preselected.
24. Press [SET] to download the configuration to the device.
If the device does not have any alarm or warning, [Good] will be displayed.
If the device has an alarm or warning, the number of errors and the
corresponding fault number will be shown.
The parameter [Ttl2] and [Ttl3] can be configured in the same way.
25. Press and hold [SHIFT] and press [SET] twice to go back to the menu [Easy setup
wizard].

TN-P-20210524-01
18

You might also like