SERVICE MANUAL

CODE :00ZPNUH861S3E

4K Ultra HD Commercial TV
PN-UH861
4K Ultra HD TV
PN-UH551
PN-UH501
MODEL PN-UH431

CONTENTS

CHAPTER 1. OUTLINE OF THE PRODUCT ····································· 1-1

CHAPTER 2. INSTALLATION, SETTING ········································· 2-1

CHAPTER 3. IMPORTANT INFORMATION FOR SERVICING THE DISPLAY ·· 3-1

CHAPTER 4. SERVICE MENU AND SERVICE TOOL ························· 4-1

CHAPTER 5. FIRMWARE UPDATE PROCEDURES··························· 5-1

CHAPTER 6. DISASSEMBLY AND ASSEMBLY ································ 6-1

CHAPTER 7. TROUBLESHOOTING················································ 7-1

CHAPTER 8. HARDWARE DESCRIPTIONS ····································· 8-1

Parts marked with “!” are important for maintaining the safety of the set. Be sure to replace
these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for

SHARP CORPORATION
after sales service only.
The contents are subject to change without notice.
LEAD-FREE SOLDER
CODE :00ZPNY325SM/E
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.

The alphabet following the LF mark shows the kind of lead-free solder.

<Solder composition code of lead-free solder>

Solder composition Solder composition code
Sn-Ag-Cu a

Sn-Ag-Bi
b
Sn-Ag-Bi-Cu

Sn-Zn-Bi z

Sn-In-Ag-Bi i

Sn-Cu-Ni n

Sn-Ag-Sb s

Bi-Sn-Ag-P
p
Bi-Sn-Ag

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

When repairing a lead-free solder PWB, use lead-free solder thread. Never use conventional lead solder thread, which may cause a
breakdown or an accident.

Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclu-
sive-use soldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering
capacity is inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land
separation or may exceed the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when
completion of soldering is confirmed.

Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip
after completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.

CAUTIONS
CAUTIONS
THERE
THERE IS
IS A
A RISK
RISK OF
OF EXPLOSION
EXPLOSION IF
IF THE
THE BATTERY
BATTERY
IS
IS REPLACED
REPLACED BY BY AN
AN INCORRECT
INCORRECT TYPE.
TYPE.
PROPERLY
PROPERLY DISPOSE
DISPOSE OF
OF USED
USED BATTERIES
BATTERIES ACCORDING
ACCORDING
TO
TO THE
THE INSTRUCTIONS.
INSTRUCTIONS.

CAUTION: Double pole, neutral fusing. Disconnect mains before servicing.

ATTENTION. Double pôle, fusible sur le neutre. Débrancher l'alimentation avant l'entretien.
 Contents

CHAPTER 1. OUTLINE OF THE PRODUCT

1．PRODUCT FEATURES 1-1
2．SPECIFICATIONS 1-2
3．PARTS NAME AND FUNCTION 1-6

CHAPTER 2. INSTALLATION, SETTING

1．INSTALLATION 2-1
2．OSD MENU 2-2

CHAPTER 3. IMPORTANT INFORMATION FOR SERVICING THE DISPLAY

1．MAIN PWB, LCD MODULE, ANDROID PWB REPLACEMENT PROCEDURE 3-1

CHAPTER 4. SERVICE MENU AND SERVICE TOOL

1．SERVICE MENU 4-1
2．SERVICE TOOL 4-2
3．SERIAL NUMBER WRITING PROCEDURES 4-6
4．USAGE TIME SETTING PROCEDURES 4-7
5．ABNORMAL TEMPERATURE STATUS 4-8
6．WHITE BALANCE SETTING TOOL OPERATION PROCEDURE 4-9

CHAPTER 5. FIRMWARE UPDATE PROCEDURES

1．FIRMWARE 5-1
2．HOW TO UPDATE MAIN FIRMWARE VIA USB FLASH DRIVE 5-2

CHAPTER 6. DISASSEMBLY AND ASSEMBLY

1．PWB AND WIRING DIAGRAM 6-1
2．REAR CABINET 6-6
3．POWER UNIT PWB 6-9
4．MAIN PWB 6-10
5．KEY PWB 6-12
6．IR PWB 6-14
7．SPEAKER 6-15
Contents
 Contents

8．LED DRIVER PWB 6-16

9．LCD MODULE 6-17

CHAPTER 7. TROUBLE SHOOTING

1．HOW TO RESPOND BY TROUBLE SYMPTOM (IN CASE OF NON-DEFECTIVE MODE) 7-1
2．HOW TO RESPOND BY TROUBLE SYMPTOM (IN CASE OF DEFECTIVE MODE) 7-3

CHAPTER 8. HARDWARE DESCRIPTIONS

1．CIRCUIT DESCRIPTIONS 8-1
2．BLOCK DIAGRAM 8-3
3．CONNECTOR TABLE 8-8

Contents
CHAPTER 1. OUTLINE OF THE PRODUCT

1. PRODUCT FEATURES
1-1. Rich Lineup From 86V Large Display to 43V Medium/Small Display

1-2. High Definition 4K LCD Panel for All Sizes

1-3. Equipped with TV Tuner for North America (ATSC)

1-4. TARGET USER

PN-UH861/UH551/UH501/UH431 OUTLINE OF THE PRODUCT 1-1

2. SPECIFICATIONS
2-1. PRODUCT SPECIFICATIONS
Model PN-UH861 PN-UH551
86" Class [85-5/8 inch (217.426 cm) 55" Class [54-5/8 inch (138.783 cm)
LCD component
diagonal] TFT LCD diagonal] TFT LCD
Max. resolution (pixels) 3840 x 2160
Max. colors Approx. 1.07 billion colors
Pixel pitch 0.4935 mm (H) × 0.4935 mm (V) 0.315 mm (H) × 0.315 mm (V)
2
Brightness (typical) *1 400 cd/m
Contrast ratio (typical) 1200:1 4000:1
Viewing angle 178° right/left/up/down (contrast ratio ≥ 10)
74-5/8 (W) x 41-15/16 (H) 47-5/8 (W) x 26-13/16 (H)
Screen active area inch (mm)
(1895.04 x 1065.96) (1209.6 x 680.4)
Computer input signal Analog RGB (0.7 Vp-p) [75 Ω]
Sync signal Horizontal/vertical separate (TTL: positive/negative)
Plug and play VESA DDC2B
Input Video Mini D-sub 15 pin, 3 rows x 1
terminals HDMI x 2
Serial (RS-232C) D-sub 9 pin x 1
Audio 3.5 mm mini stereo jack x 1
Antenna terminal (ANTENNA/CABLE IN) 75ΩF type
(Antenna input)
Output Audio RCA pin (L/R) x 1
terminals IR Pass-Through x1
USB Port USB (USB 2.0 compliant) x 1
LAN Terminal 10 BASE-T/100 BASE-TX
TV Video Color system NTSC-M/PAL-N/PAL-M
TV TV-standard Analog NTSC
Function Digital ATSC
Receiving Analog 55.25 – 801.25 MHz
Channel VHF/UHF
Digital VHF/UHF 57 – 861MHz
TV-Tuning system Auto Preset 135 ch
STEREO/BILINGUAL BTSC system
Speaker output 10 W + 10 W
Power requirement AC 120 V, 60 Hz
Operating temperature *2 32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption (standby mode *3) 330 W (0.5 W) 140 W (0.5 W)
Approx. 75-7/8 (W) x 3-1/8 (D) x Approx. 48-3/4 (W) x 3-1/8 (D) x 28
Dimensions (excluding protrusions) inch (mm)
43-1/4 (H) (1928 x 79 x 1099) (H) (1239 x 79.2 x 711.5)
Weight lbs. (kg) Approx. 110.2 (50) Approx. 33.1 (15)
Operating time 16 hours / day

PN-UH861/UH551/UH501/UH431 OUTLINE OF THE PRODUCT 1-2

 Model PN-UH501 PN-UH431
50" Class [49-1/2 inch (125.730 cm) 43" Class [42-1/2 inch (107.986 cm)
LCD component
diagonal] TFT LCD diagonal] TFT LCD
Max. resolution (pixels) 3840 x 2160
Max. colors Approx. 1.07 billion colors Approx. 1.07 billion colors
Pixel pitch 0.2854 mm (H) × 0.2854 mm (V) 0.2451 mm (H) × 0.2451 mm (V)
2
Brightness (typical) *1 400 cd/m
Contrast ratio (typical) 4000:1
Viewing angle 178° right/left/up/down (contrast ratio ≥ 10)
43-1/8 (W) x 24-1/4 (H) 37-1/16 (W) x 20-13/16 (H)
Screen active area inch (mm)
(1095.84 x 616.41) (941.18 x 529.41)
Computer input signal Analog RGB (0.7 Vp-p) [75 Ω]
Sync signal Horizontal/vertical separate (TTL: positive/negative)
Plug and play VESA DDC2B
Input Video Mini D-sub 15 pin, 3 rows x 1
terminals HDMI x 2
Serial (RS-232C) D-sub 9 pin x 1
Audio 3.5 mm mini stereo jack x 1
Antenna terminal (ANTENNA/CABLE IN) 75ΩF type
(Antenna input)
Output Audio RCA pin (L/R) x 1
terminals IR Pass-Through x1
USB Port USB (USB 2.0 compliant) x 1
LAN Terminal 10 BASE-T/100 BASE-TX/1000 BASE-T
TV Video Color system NTSC-M/PAL-N/PAL-M
TV TV-standard Analog NTSC
Function Digital ATSC
Receiving Analog
55.25 – 801.25 MHz
Channel VHF/UHF
Digital UHF 57 - 861 MHz
TV-Tuning system Auto Preset 135 ch
STEREO/BILINGUAL BTSC system
Speaker output 10 W + 10 W
Power requirement AC 120 V, 60 Hz
Operating temperature *2 32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption 130 W (0.5 W) 105 W (0.5 W)
(input signal waiting mode / standby mode *3)
Approx. 44-1/4 (W) x 3-1/16 (D) x Approx. 38-1/8 (W) x 3 (D) x 22 (H)
Dimensions (excluding protrusions) inch (mm)
25-7/16 (H) (1124 x 77 x 647) (968 x 76.8 x 559)
Weight lbs. (kg) Approx. 26.4 (12.5) Approx. 19.8 (9)
Operating time 16 hours / day
*1 Brightness will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the nature of the
equipment, it is not possible to precisely maintain a constant level of brightness.
*2 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.
In such cases, please check the temperature condition specified by the optional equipments.
*3 When “Power save mode” is set to “On”, and no optional part is attached. When “Power save mode is set to “Off” : 10W

PN-UH861/UH551/UH501/UH431 OUTLINE OF THE PRODUCT 1-3

2-2. Dimensional Drawings(That the values shown are approximate values)

[PN-UH861]

[PN-UH551]

[PN-UH501]

PN-UH861/UH551/UH501/UH431 OUTLINE OF THE PRODUCT 1-4

[PN-UH431]

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method.
SHARP recommends using M8 screws (PN-UH861), M6 screws (PN-UH551/UH501/UH431) and tighten the screws.
Note that screw hole depth of the monitor is 13/16 inch (20 mm). Loose mounting may cause the product to fall, resulting in serious
personal injuries as well as damage to the product. The screw and hole should come together with over 11/16 inch (18 mm) length of
thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or more the weight of the
monitor.

2-3. SUPPLIED COMPONENTS

LCD TV: 1
Remote control unit : 1
Power cord : 1
LR03 battery (“AAA” size) : 2
CD-ROM (Utility Disk for Windows) : 1
Setup Manual : 1
Specification sheet
Cable clamp : 2
Logo Sticker :1

* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission.
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.

PN-UH861/UH551/UH501/UH431 OUTLINE OF THE PRODUCT 1-5

3. PART NAMES AND FUNCTION

■Front view ■Rear view

[PN-UH861]

[PN-UH551/UH501/UH431]

No. Name No. Name

1 LCD panel 11 IR output terminal
2 Remote control sensor 12 HDMI1 input terminal
3 Power LED 13 HDMI2 input terminal
4 AC input terminal 14 USB port
5 Audio output terminal 15 Vents
6 RS-232C input terminal 16 VOL +/- button
7 LAN terminal 17 CH ˄/˅ button
8 Antenna terminal 18 MENU button
9 D-sub input terminal 19 Input button
10 Audio input terminal 20 Power button

PN-UH861/UH551/UH501/UH431 OUTLINE OF THE PRODUCT 1-6

■The status of Power LED
Status Status of the monitor
Off Power off
Green lit Power on
Red lit Standby mode
Green flashing (at approx. 250ms interval) Updating by USB
Red flashing (at approx. 0.5s interval) Failure to update firmware
Red and Green flashing alternatively Temperature error
(at approx. 1s interval)

■Remote control

No Name Explanation
1 Numeric input button Manually enter a channel.
You can also use the button when you enter numeric or dot.
2 DISPLAY Displays information of displayed channel or monitor.
3 MUTE Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the
previous level.
4 VOL +/- Press + or - to adjust the volume.
(Volume adjustment)
5 ENTER Confirms the setting.
Display CH list when watching TV.
6 EXIT Turns off the menu screen.
7 INPUT The menu is displayed. Press the or button to select
(Input mode selection) the input mode, and press the ENTER button to enter.
* You can change the input mode by pressing the INPUT
button of the monitor. (PN-UH551/PN-UH501/PN-UH431)
Input Video Audio
mode
TV Antenna terminal Antenna terminal

HDMI1 HDMI1 input terminal HDMI1 input terminal

HDMI2 HDMI2 input terminal HDMI2 input terminal

D-SUB D-sub input terminal Audio input terminal

USB USB port USB port

8 AUDIO Change MTS or audio language.

9 CH ˄/˅ Changes channel.
10 FAVORITE Displays registered favorite channel list.
11 Cursor These buttons are used to perform operations such as
selecting items, changing adjustment values, and moving
the cursor.
12 MENU Displays the menu screen. Returns to previous screen while
the menu items are being displayed.
(*)Buttons other than the above are not used with this monitor.

PN-UH861/UH551/UH501/UH431 OUTLINE OF THE PRODUCT 1-7

CHAPTER 2. INSTALLATION, SETTING
1. INSTALLATION
1 – 1.INSTALLAING PRECAUTIONS - To attach a VESA-compliant mounting bracket, use M8
- This product is for use indoors. [PN-UH861] or M6 [PN-UH551/PN-UH501/PN-UH431] screws
- A mounting bracket compliant with VESA specifications is that are 11/16 inch (18 mm) to 13/16 inch (20 mm) [PN-UH861]
required. or 5/16 inch (8mm) to 3/8 inch (10mm) [PN-UH551/PN-UH501/
- Since the monitor is heavy, consult your dealer before installing, PN-UH431] longer than the thickness of the mounting bracket.
removing or moving the monitor.
- Mounting the monitor on the wall requires special expertise and
the work must be performed by an authorized SHARP dealer.
- Use the monitor with the surface perpendicular to a level surface.
If necessary, the monitor may be tilted up to 20 degrees upward
or downward.
- This monitor should be used at an ambient temperature between - Do not use an impact driver.
32°F (0°C) and 104°F (40°C). Provide enough space around the - When moving the monitor, be sure to hold the parts marked by
monitor to prevent heat from accumulating inside. below. Do not hold the LCD panel. This may cause
product damage, failure, or injury.
[PN-UH861]

- If it is difficult to provide sufficient space for any reason such as

the installation of the monitor inside a housing or if the ambient
temperature may be outside of the range of 32°F (0°C) to 104°F
(40°C), install a fan or take other measures to keep the ambient [PN-UH551/PN-UH501/PN-UH431]
temperature within the required range.
- Do not block any ventilation openings. If the temperature inside
the monitor rises, this could lead to a malfunction.
- Do not place the monitor on a device which generates heat.

1-2. MOUNTING PRECAUTIONS

- When installing, removing or moving the monitor, ensure that
this is carried out by at least 2 people.
(PN-UH861 : at least 3 people)
- Be sure to use a wall-mount bracket designed or designated for - After mounting, please carefully ensure the monitor is secure,
mounting the monitor. and not able to come loose from the wall or mount.
- This monitor is designed to be installed on a concrete wall or - Do not use any screw holes other than those for mounting
pillar. Reinforced work might be necessary for some materials brackets, located on the rear of the monitor, for installation.
such as plaster / thin plastic board / wood before starting
installation.
- To attach a VESA-compliant mounting bracket, remove the
screws attached to screw holes for mounting brackets. Do not
use the removed screws to attach the mounting bracket.
(PN-UH861 ONLY)

PN-UH861/UH551/UH501/UH431 INSTALLATION, SETTING 2 - 1

2. OSD MENU
2-1. MENU ITEM DEFAULT VALUE LIST
Video adjustment and settings of various functions are enabled.
Press the MENU button to display the menu screen.

Picture Audio Setup

AV mode

Advance d

Brightne ss

Con trast

Blac k level

Tint

Color

Sharpn ess

(Caution)
- Do not turn off the power while the menu items are being displayed. Doing so may initialize the settings.
- This cannot be displayed when the input mode is [USB]. Change an input mode to other than [USB] before performing these operations.

ITEM DEFAULT VALUE

PICTURE AV MODE (DYNAMIC / PC / STANDARD / CINEMA / GAME / CUSTOM) TV : STANDARD
OTHER : PC
ADVANCED WIDE MODE (WIDE / ZOOM / NORMAL / DOT BY DOT) WIDE
OVERSCAN (OFF / ON) OFF
(In case of HDMI1/HDMI2)
COLOR TEMP. (LOW / MIDDLE / HIGH / THRU) MIDDLE
NOISE REDUCTION (OFF / LOW / MIDDLE / HIGH) OFF
ACTIVE CONTRAST (OFF / ON) OFF
MOTION ENHANCEMENT (OFF / LOW / HIGH / FILM MODE) OFF
(PN-UH861/PN-UH551))
BRIGHTNESS (0 - 50) 40
BLACK LEVEL (0 - 100) 50
CONTRAST (0 - 100) 50
COLOR (0 - 100) 50
TINT (R50 - R1, 0, G1 – G50) 0
SHARPNESS (0 - 100) 50
AUDIO BALANCE (-50 - 0 - +50) 0
BASS (0 - 100) 0
TREBLE (0 - 100) 0
SPEAKER (DISABLE / ENABLE) ENABLE
SURROUND (OFF / ON) OFF
AUDIO OUTPUT (VARIABLE / FIXED) VARIABLE
TV CH SEARCH (CABLE / ANTENNA) -
CH MEMORY -
FAVORITE CH -
MTS/SAP (MONAURAL / STEREO / SAP) STEREO
AUDIO LANGUAGE (ENGLISH / FRENCH / SPANISH) ENGLISH

PN-UH861/UH551/UH501/UH431 INSTALLATION, SETTING 2 - 2

 ITEM DEFAULT VALUE
SETUP LANGUAGE (ENGLISH / FRENCH / SPANISH) ENGLISH
COMMUNICATION RS-232C/LAN SELECT RS-232C
SETTING LAN SETUP NETWORK DHCP (NO USE / USE) -
INFORMATION IP ADDRESS -
SUBNET MASK -
GATEWAY -
MAC ADDRESS -
DHCP (NO USE / USE) USE
IP ADDRESS 192.168.150.2.
SUBNET MASK 255.255.255.0.
GATEWAY 0.0.0.0
SET -
PARENTAL NO RATING (BLOCK / NO BLOCK) NO BLOCK
CONTROL US MPAA NONE
(NONE / G / PG / PG-13 / R / NC-17 / X)
TV GUIDELINES NONE
(NONE / TV-Y / TV-Y7 / TV-G / TV-PG /
TV-14 / TV-MA )
CANADA CAN ENGLISH RATINGS E
(E / C / C8+ / G / PG / 14+ / 18+)
CAN FRENCH RATINGS E
(E / G / 8ans+ / 13ans+ / 16ans+ / 18ans+)
RRT HUMOR LEVEL DH (OFF / ON) OFF
MH (OFF / ON) OFF
H (OFF / ON) OFF
VH (OFF ON) OFF
EH (OFF / ON) OFF
MYSTERY CHILDREN (OFF / ON) OFF
YOUNG (OFF / ON) OFF
ADULT (OFF / ON) OFF
MIDDLE (OFF / ON) OFF
AGED (OFF / ON) OFF
RESET RRT5 (NO / YES) -
SETTING SECRET NO -
RESET (NO / YES) -
CLOSED CAPTION CAPTION DISPLAY (CC OFF / CC ON / CC ON WHEN MUTE) CC OFF
ANALOG CC (CC1-CC4 / TEXT1-TEXT4) CC1
DIGITAL CC (CS1-CS6 / CC1-CC4) CS1
CAPTION STYLE (DEFAULT / CUSTOM) DEFAULT
SETUP SIZE (SMALL / NORMAL / LARGE) NORMAL
FONT (DEFAULT / STYLE1 -7) DEFAULT
TEXT COLOR WHITE
(BLACK / WHITE / RED / GREEN / BLUE /
YELLOW / MAGENTA / CYAN)
BACKGROUND COLOR BLACK
(BLACK / WHITE / RED / GREEN / BLUE /
YELLOW / MAGENTA / CYAN)

PN-UH861/UH551/UH501/UH431 INSTALLATION, SETTING 2 - 3

 ITEM DEFAULT VALUE
SETUP HDMI CEC LINK (OFF /ON) ON
HDMI MODE (MODE1 / MODE2) MODE1
SCREEN AUTO ADJUST (D-SUB) -
H-POS (D-SUB) (0 - 100) 50
V-POS (D-SUB) (0 - 100) 50
CLOCK (D-SUB) -
PHASE (D-SUB) -
RESET (NO / YES) -
NO SIGNAL OFF (ENABLE / DISABLE) ENABLE
POWER SAVE MODE (OFF / ON) OFF
AUTO PLAY (DISABLE / PHOTO / VIDEO) OFF
MONITOR BUTTON LOCK (UNLOCKED / LOCKED / LOCK ALL) UNLOCKED
RC CONTROL LOCK UNLOCKED
(UNLOCKED / LOCK ALL / LOCK EXCEPT VO / LOCK EXCEPT PO)
FRONT INDICATOR LIGHT (OFF / ON) ON
INFORMATION -
(Display “MODEL NAME” and “VERSION”(firmware version) and “S/N”(serial number))
ALL RESET (YES / NO) -

2-2. INFORMATION (DISPLAY MONITOR INFORMATIONS

If press [INFORMATION] button of the remote controller, “INFORMATION” on “SETUP” menu is shown focusing “INFORMATION”.
In case of OSD, “INFORMATION” is able to be shown on “INFORMATION” of “SETUP” menu.

[Display Information]
- MODEL NAME : Indicate the model name.
- VERSION : Indicate firmware version
- S/N : Indicate the product serial number.

PICTURE AUDIO SETUP

LANGUAGE MODEL NAME:

HDMI CEC LINK PN-UHｘｘ1

HDMI MODE

COMMUNICATION SETTING
VERSION:
SCREEN
XX.XX
PANEL LOCK

IR LOCK S/N:

INFORMATION 8F1234 56

ALL RESET

M OVE OK ENTER MENU RET URN EXIT EXIT

PN-UH861/UH551/UH501/UH431 INSTALLATION, SETTING 2 - 4

CHAPTER 3. IMPORTANT INFORMATION FOR SERVICING THE DISPLAY

1. MAIN PWB, LCD MODULE, ANDROID PWB REPLACEMENT PROCEDURES

The following information as well as user setting information is saved to the EEPROM controlled by main firmware.
<INFORMATION STORED IN THE EEPROM’S CONTROLLED BY THE MAIN FIRMWARE.>
- SERIAL NUMBER
- USAGE TIME
- WHITE BALANCE SETTING VALUE
- CALIBRATION SETTING VALUE

Therefore, when the Main PWB or the LCD module and Android PWB is replaced, initialization and setting must be performed.

1-1. INFORMATION ITEMS

ITEM CONTENT
SERIAL NUMBER The machine has its own serial number which is described on the nameplate at the back of the machine.
USAGE TIME This information is linked with the LCD module. When replacing the Main PWB, read the information before
replacement, and write it to the new Main PWB after replacement. It is necessary to initialize this setting
when the LCD module is replaced.
WHITE BALANCE This information is linked with the LCD module. When replacing the Main PWB, read the information before
SETTING VALUE replacement, and write it to the new Main PWB after replacement. Execute resetting when the LCD module
is replaced.
CALIBRATION Since a service part Main PWB has been adjusted, there is no need to set when replacing the Main PWB.
SETTING VALUE Setting may be required depending on the replaced part.

PN-UH861/UH551/UH501/UH431 IMPORTANT INFORMATION FOR SERVICING THE DISPLAY 3-1

1-2. MAIN PWB REPLACEMENT PROCEDURES
1) Read the following information from the monitor before replacement of the Main PWB.
- USAGE TIME
→ Service tool [Usage Time]
- SERIAL NUMBER
→Service tool [Serial Number]
- WHITE BALANCE VALUE
→Service tool [White Balance]
(MEMO)
- The machine does not operate before replacement and reading cannot be made, this procedure is not required.
2) Replace the Main PWB.
3) Each service part has the firmware written in it. If necessary, the firmware should be updated to the latest.
→ CHAPTER 5. FIRMWARE UPDATE PROCEDURES”
4) Set the MODEL TYPE depending on the destination. The default destination of service parts is “JP.”
→ Service Menu [Model Type]
5) Execute FACTORY RESET.
→Service Menu [Reset to Default]
6) Write the information read in the above step 1).
When the reading cannot be executed, perform the following operation.
- Set “0” to USAGE TIME and perform initialization.
- Reset the WHITE BALANCE set values.

1-3. LCD MODULE REPLACEMENT PROCEDURES

1) Set “0” to USAGE TIME and perform initialization.
→ Service tool [Usage Time]
2) Reset the WHITE BALANCE set values.
→ Service tool [White Balance]

PN-UH861/UH551/UH501/UH431 IMPORTANT INFORMATION FOR SERVICING THE DISPLAY 3-2

 3 : ’19/Feb

CHAPTER 4. SERVICE MENU AND SERVICE TOOL

1. SERVICE MENU
Press the [FUNCTION], [], [] , [] and [] keys in sequence.

<Note>
- The service menu is also displayed by the conventional method.
Hold [DISPLAY] key of the remote control (“F” mark is displayed in the upper left corner of screen), press the [], [] , [] and [] keys
in sequence.
- “F” mark which is displayed by holding [DISPLAY] key is displayed in red when the monitor button lock or the RC control lock is set to
other than “Unlock”.
For the other cases, it is displayed in green. (The red color of “F” mark taked priority.)
[CAUTION]
3
Please close the active Service menu screen by pressing the “EXIT” and/or the “ENTER” button on the remote control
before power cycle of unit.
If AC power cord is unplugged while the service menu was on display,
the “PICTURE” setting in OSD menu changes to Custom and previously saved values are overwritten and reset to default.

[Display of Service Menu]

Brand SHARP
Model Name PN-UH861
Scaler MSD91H
Panel type XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
Firmw are Ver VXX.XX
PQ ver N/A
AQ ver N/A
Date 2018/1/30

Adjust R/G/B Gain/Offset

Current Source HDMI1
Auto Color Pass
(ADC)
Red Gain 1302
Green Gain 1299
Blue Gain 1302
Red Offset 0
Green Offset 0
Blue Offset 0
HDMI debug information
Resolution / V-Freq
Color space of input signal
AVI infoframe
HDMI Vender Spec IF
HDCP
TV signal debug information
Physical channel
Signal strength
Quality
Defect Abnormal Temperature
Forcibly Turn Off
Model Type US <= Select model type

Thermal
Audio Ctrl On
Burn In Off
Default Language English
EEPROM Init
SSC
Debug Mode Off
Reset to Default N/A <= Execute factory reset
Factory Setting
Exit

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 1
2. SERVICE TOOL
2-1. Overview
■ Operation Environment
OS Windows 7
(32bit/64bit) Windows8.1
Windows 10
Communication - RS-232C port which is recognized as COM port which recognize the communication, (9600 / 19200 /
port 38400bps communications are available.)
- LAN (100BASE TX/10BASE TX)
When communicating, both the PC side and the display side need to be set.
(Memo)
This tool does not operate properly in the power standby state or the signal standby. Put a signal on the current input or power
management is set “No”.
When connecting to this unit with LAN cable, connect with a crossover cable when connecting directly with this unit, with a straight
cable in case of via Hub. When connecting directly, it is necessary to set both PC and this machine. If the machine is already
connected to the network, consult with the network administrator about the setting of the PC for connecting to the network.

■ How to Install Service Tool

1) All the tools are provided in a zip file. Decompress the zip file to C:¥
<Caution>
The operation may fail if space is inserted to folder path.
2) In case the Microsoft Visual C++ 2012 Redistribute(x86) is not installed, execute bundled “vcredist_x86.exe” and install library.
* In case an error message "Command line option syntax error. Type Command /? for Help." is displayed, double-byte character
(Japanese) may be included in user name. Log on with the user name with administrator authority which includes only one-byte
character and install. If no user has been registered, go to User Accounts in Control Panel and register a user.
3) Download .Net Framework 4.5 or later from Microsoft home page and install before using this tool.

■ How to Confirm Version information of Service Tool

1 ) Activate Launcher Tool. Confirm version number of service tool shown on upper right of the window.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 2
■ USE INSTRUCTIONS
1 ) Execute “ServiceToolsLauncher.exe” in the folder where the service tool is extracted.
<Note>
- If it cannot be executed, the library may not be installed. In this case, please install the library, referring to Installation Procedures shown
above.
→ Refer to “■How to Install Service Tool”.
- In case of the window of “User Account Control” is displayed as shown below, need to click [Allow].

2 ) Once the service tool is booted, press the button as needed to conduct operations.

ITEM BUTTON DESCRIPTION

Setting Serial Number Read / Write the serial number of the monitor.
Usage Time Read / Write the Usage Time to the monitor.
Abnormal Temperature Read abnormal temperature time and temperature of the monitor.
Display Firmware Create Usb Drive Copy files for updating the firmware to the USB flash drive.
* Do not copy the update files for other inch size to the same USB flash
drive. IF there are two or more binary files, update will not be executed.
LCD Module Data PN-UH861 Set White balance settings of the display.
(White Balance) PN-UH651
PN-UH501

PN-UH431
Library install Visual C++ 2012 Install Microsoft Visual C++ 2012 Redistributable (x86).

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 3
■ HOW TO SET THE CONNECTION
1) Press [Serial Number] button of the Service Tool Launcher.
2) Press [Connection setting]

3) Set the following connection setting.

①
②

④ ⑤

⑧ ⑨

NO ITEM DESCRIPTION
① Serial connection Select the connection method.
Connection is done by RS-232C serial connection.
② RS232C connection port Specify the connection port of RS-232C
Select COM1(default)～COM256 from the pull down list.
If ① is not selected, gray out.
③ RS232C baud rate Specify the baud rate of RS232 connection port.
9600 Fixed
If ① is not selected, gray out.
④ TCP/IP Select the connection method.
Connection is done by TCP/IP connection(LAN).
⑤ Host Specify the IP address of the display to be connected.
(Adjust to display setting)
If ④ is not selected, gray out.
⑥ TCP port Specify the data port of the display to be connected.
default：10008
(Adjust to display setting)
If ④ is not selected, gray out.
⑦ Display ID Specify the Display ID to be connected.
If not correspond to daisy chain, gray out.
⑧ Setting Confirm the setting.
⑨ Cancel Suspend the setting and close the screen.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 4
4) When the connection error occurs, the following message is displayed.
CODE ERROR MESSAGE DESCRIPTION
E1 Cannot open interface. The specified connection port could not be opened.
Cannot connect.
Please confirm setting.
E2 Time out. Cannot connect. Could not connect with the display and timeout occurred.
Please confirm setting.
E3 Monitor return "ERR" code. There was an error response from the display and connection failed.
E4 Interface is locked. The RS232C/LAN setting of the display is set to “prohibit”
E5 Authentication is failed. Authentication failed on LAN connection.
E6 Access is denied. Access is denied
E7 Unselected error. The connection setting of the display and the tool do not match.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 5
3. SERIAL NUMBER WRITING PROCEDURES
3-1. START-UP OF THE SERIAL NUMBER SETTING TOOL
Press [Serial Number] button of the Service Tool Launcher.

3-2. SERIAL NUMBER SETTING PROCEDURES

The procedures of setting serial numbers with use of the Serial Number Setting Tool are as follows.
1) Press [Connection Setting...] button to configure the communication settings.
2) Input the serial number you need to set in the field of Write Data.
3) Press [Write] button.
4) Press [Read] button, and confirm that the set serial number is displayed in the Read Data field.

3-3. SERIAL NUMBER CHECK METHOD

If press [INFORMATION] button of the remote controller, “INFORMATION” on “SETUP” menu is shown focusing “INFORMATION”.
In case of OSD, “INFORMATION” is able to be shown on “INFORMATION” of “SETUP” menu.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 6
4. USAGE TIME SETTING PROCEDURE
4-1. START-UP OF THE USAGE TIME SETTING TOOL
Press [Usage Time] button of the Service Tool Launcher.

4-2. USAGE TIME SETTING PROCEDURES

The procedures of setting usage time with use of the Usage Time Setting Tool are as follows.
1) Press [Connection Setting...] button to configure the communication settings.
2) Input the usage time you need to set in the field of Write Data.
It should be from “000000” to “200000.” Make sure to input a 6-digit number.
3) Press [Write] button.
4) Press [Read] button, and confirm that the set usage time is displayed in the Read Data field.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 7
5. ABNORMAL TEMPERATURE STATUS
5-1. START-UP OF ABNORMAL TEMPERATURE TOOL
Press [Abnormal Temperature] button of the Service Tool Launcher.

5-2. ABNORMAL TEMPERATURE STATUS

The procedures of setting usage time with use of the Usage Time Setting Tool are as follows.
1) Press [Connection Setting...] button to configure the communication settings.
2) Press [Read] button, and get the abnormal time and temperature from the monitor.

ITEM DESCRIPTION
The last usage time (detection) Display the last usage time when the abnormal temperature error happens.
The last temperature (detection) Display the last temperature value when the abnormal temperature happens.
The last usage time (turned off) Display the last usage time when the monitor turned off.
The last temperature (turned off) Display the last temperature value when the monitor turned off.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 8
6. WHITE BALANCE SETTING TOOL OPERATING PROCEDURE
6-1. START-UP OF THE WHITE BALANCESETTING TOOL
Press [White Balance] button of the Service Tool Launcher.

6-2. THE WHITE BALANCE SETTING TOOL PROCEDURE

■ How to read the white balance settings
The procedures of writing the settings that have been previously readout with use of the White Balance Setting Tool are as follows.
1) Press [Connection Setting...] button to configure the communication settings.
2) Turn on the power of Information Display.
3) Press [Read& Save] button.
4) When all settings have been read out, the set values are displayed and the dialogue box of file save appears. At this point, the default
file name is “[Model Name]_[Serial Number] _[Date(YYYYMMDD)].wni”. After confirming the file name, press [Save] button to save the
settings.
6) Confirm that the “Level” values in the read settings are the same as the values in the above illustration. If the Level values that you’ve
got don’t agree with the above settings, the setting data cannot be taken over. In this case, refer to the procedures: “WHEN
REPLACING THE PANEL OR WHEN AN OLD PWB DOES NOT OPERATE” and perform the reset of settings to set the default.
(Normally, this case doesn’t happen unless changes are made individually.)

■ How to write the white balance settings

The procedures of writing the settings that have been previously read out with use of the White Balance Setting Tool after exchange Main
pwb are as follows.
1) Press [Connection Setting...] button to configure the communication settings.
2) Turn on the power of Information Display.
3) Press [Load File...] button to select the setting file.
4) Press [Write] button, and the set values are written.

6-3. WHEN REPLACING THE LCD MODULE OR WHEN AN OLD PWB DOES NOT OPERATE
The procedures of resetting the settings to default are as follows.
1) Press [Connection Setting] button to configure the communication settings.
2) Turn on the power of Information Display.
3) Press [Reset] button. The White Balance settings are set to default.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 9
6-4. ERROR MESSAGE
When various errors occur, the following messages is displayed.
CODE ERROR MESSAGE DESCRIPTION
E1 Write is failed. The writing of white balance settings data is failed or is canceled.
E2 Reset process is failed. Reset process is failed.
M1 This Monitor is not Support. The data to be written and the display series ID do not match.
Is write processing continued?
M2 Writing data is not for this monitor. The data to be written is not for the target display.
Is write processing continued?
M3 Serial Number is different between The date to be written and the serial number of the display do
monitor and writing data. Is write not match.
processing continued?
M4 Model Name is different between The data to be written and the model name of the display
monitor and writing data. do not match.
Is write processing continued?
M5 Write is completed. The writing of white balance settings data is completed.

PN-UH861/UH551/UH501/UH431
SERVICE MENU AND SERVICE TOOL 4 - 10
CHAPTER 5. FIRMWARE UPDATE PROCEDURES

1. FIRMWARE
1-1. OVERVIEW
Main firmware, LAN micon firmware and FRC firmware (Only PN-UH861) are updated.

[Construction of firmware]
Content Description
Main firmware The firmware of Scaler (MStar MSD91H)
LAN micon firmware The firmware of MCU (WIZnet W7500) and it controls LAN command.
FRC firmware The firmware of FRC(Frame rate control) [Only PN-UH861]

PN-UH861/UH551/UH501/UH431 FIRMWARE UPDATE PROCEDURES 5-1

2. HOW TO UPDATE MAIN FIRMWARE VIA USB FLASH DRIVE
2-1. USB FLASH DRIVE
Use the USB flash drive which supports the following standard.

- Format : FAT32
- USB : 2.0/1.1
<Caution>

- Set the proper volume label name.

- It does not correspond to SD card reader.
- It does not correspond to USB HUB
- Do not use the USB Flash Drive enciphered

(*) The USB flash drive should be emptied beforehand.

2-2. UPDATE ALL FIRMWARES VIA USB FLASH DRIVE

1) Click [Create Usb Drive] button of the Service Tool Launcher.
2) Insert the USB flash drive into the PC and select the USB flash drive from the pull down list. Then, click “Copy”.

Copy the update file under the root of the USB flash drive.
ex.) root
- 2K18_SHARP_PN_UH_MODEL_USA_MSD91H_MULTI_PANEL_V*.**.bin
- 2K18_TPV_SHARP_PD_TV_PCB_W7500_V*.**.bin
- 2K18_TPV_SHARP_PD_MST7484_FRC_V*.**.bin
3) Insert the USB flash drive to the monitor.
4) Turn on the monitor.
Updating the firmware is executed automatically.
* If turn on/off the main power of the monitor inserting the USB flash drive, same updating is executed.
5) The monitor detects the target file and displays the confirmation screen.

Do you want to update?

(Main)

Yes No

6) If move the focus onto “Yes” and press “ENTER” button, then updating will start.
And then if select “No”, the confirmation screen disappears.

PN-UH861/UH551/UH501/UH431 FIRMWARE UPDATE PROCEDURES 5-2

7) The progress screen appears while updating.
Updating software.

Do not remove the USB flash drive

while making is in progress.
And do not turn off the power of the TV.

8) After complete updating the main firmware, the monitor displays the confirmation screen of updating LAN firmware.
If move the focus onto “Yes” and press “ENTER” button, then updating will start.

9) (Only PN-UH861) After complete updating the LAN firmware, the monitor displays the confirmation screen of updating FRC firmware.
If move the focus onto “Yes” and press “ENTER” button, then updating will start.

10) After complete updating all firmwares, the complete screen as follows.

Remove the USB flash device and press the

ENTER button to restart the TV.

11) Eject the USB flash drive and press “ENTER” button, then the display will reboot.

<Note> If fail updating, below screen appears.

Update failed.
1. Remove the USB flash device device
2. Restart the TV.
3. Insert the USB flash device and restart
the process.

PN-UH861/UH551/UH501/UH431 FIRMWARE UPDATE PROCEDURES 5-3

2-3. CAUTION
- Do not save data other than the firmware data in the USB flash drive.
- It is not possible to use the USB flash drive with the security function with this procedure.
- When the file name of the created updater file is changed, it is not possble to carry out the update.
- Do not disconnect the USB flash drive during updating.
- When the firmware versions before updating and after updating are the same, updating is stated.

2-4. ERROR MASSAGE

When various errors occur, the following messages is displayed.
CODE ERROR MESSAGE DESCRIPTION
E1 Cannot Copy files Fail to copy files
M1 Overwrite [filename]? Confirm to overwrite [filename] file.
M2 Success to copy files Success to copy all files
M3 Cancel to copy files Select “No” when overwrite all files.

PN-UH861/UH551/UH501/UH431 FIRMWARE UPDATE PROCEDURES 5-4

CHAPTER 6. DISASSEMBLY AND ASSEMBLY
- Do not touch the PWBs which employ lead-free solder with bare hands. Always use gloves.
- Use the earth band when performing the procedures.
- When servicing the Display such as replacing a PWB, make sure to service with the Display laid and with a protective sheet spread over
the LCD panel.
- While working with the Display laid, or when moving the Display after the work, applying stress to the bezel may cause it to get deformed.
Be sure to handle it with great care.
<Note>
When the Rear cabinet is attached, refer the following “PWB AND WIRING DIAGRAM”, assemble the rear cabinet not to pinch
the cable in the rear cabinet.

1. PWB AND WIRING DIAGRAM

[PN-UH861]
■ Main Body

No. PWB Name No. Cable Name

1 Power PWB A LED cable A
2 LED Driver PWB (a part of LCD module) B LED cable B
3 Main PWB C Main PWB-Power PWB cable
4 Speaker D Main PWB-T-CON PWB FFC
5 IR PWB E Main PWB-T-CON PWB cable
F Speaker cable
G IR-Key cable

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 1

■ Rear cabinet

No. PWB Name No. Cable Name

1 Key PWB A Key relay cable

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 2

 2 : ’18/Dec

[PN-UH551]
2
■ Main Body

A
2

B
3

C
1

6 E 6 4
D
5

No. PWB Name No. Cable Name

1 LED Driver PWB A Power PWB - LED Driver PWB cable
2 Power PWB B Power PWB - Main PWB cable
3 Main PWB C Main PWB – T-CON PWB FFC (LVDS cable)
4 Key PWB D IR/Key cable
5 IR PWB E Speaker cable
6 Speaker

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 3

2 : ’18/Dec

[PN-UH501]
2
■ Main Body

A
2 B

C
1

D 4
6 6 5

No. PWB Name No. Cable Name

1 LED Driver PWB A Power PWB - LED Driver PWB cable
2 Power PWB B Power PWB - Main PWB cable
3 Main PWB C Main PWB – T-CON PWB FFC (LVDS cable)
4 Key PWB D IR/Key cable
5 IR PWB E Speaker cable
6 Speaker

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 4

2 : ’18/Dec

2 PN-UH431]
■ Main Body

A B

E 4
6 D
6 5

No. PWB Name No. Cable Name

1 LED Driver PWB A Power PWB - LED Driver PWB cable
2 Power PWB B Power PWB - Main PWB cable
3 Main PWB C Main PWB – T-CON PWB FFC (LVDS cable)
4 Key PWB D IR/Key cable
5 IR PWB E Speaker cable
6 Speaker

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 5

2. REAR CABINET
[PN-UH861]

1) Remove the screw ( x26pcs, x4pcs)

2) Remove the rear cabinet carefully and disconnect the connection between main body and rear cabinet.

Disconnect this connection

Rear cabinet

Main body

LCD module

←Upper side Bottom side →

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 6

2 : ’18/Dec

[PN-UH551]
2
1) Remove the screw ( x18pcs, x4pcs, x1pc )

[PN-UH501]
1) Remove the screw ( x15pcs, x4pcs, x1pc )

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 7

2 : ’18/Dec

[PN-UH431]
2
1) Remove the screw ( x14pcs, x2pcs, x1pc )

[PN-UH551/UH501/UH431]
<Note>
When tighten the screws in positions, be careful of the tightening torque (5.0±0.5kgf).
<Note>
When assemble the rear cabinet, be careful of the fitting at the bottom of the set.

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 8

2 : ’18/Dec

3. POWER UNIT PWB

[PN-UH861]

1) Remove the screws (9pcs) and disconnect the connection of the cables (3 positions)
and remove the power unit pwb.

[PN-UH551/UH550/UH431]
2
1) Remove the screws ( x 3pcs, x 2pcs) and disconnect the connection of the cables (2 positions)
and remove the power unit pwb.

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 9

4. MAIN PWB
[PN-UH861]

1) Remove the screws (4pcs) and disconnect the connection of the cables (5 positions).

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 10

 2 : ’18/Dec

[PN-UH551/UH501/UH431]
2
1) Remove the screws (4pcs) and disconnect the support pin (1pc) and disconnect the connection of the cables (3 positions).

<Note>
The following 2 screws are tightened to the hexagon bolts.
Be careful of the tightening torque.
The screw : 5.0±0.5kgf
The hexagon bolt : 5.5±0.5kgf

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 11

 2 : ’18/Dec

5 KEY PWB
[PN-UH861]
1) Remove the rear cabinet (Refer to “2. REAR CABINET”).
2) Remove the screws (2pcs) and disconnect the connection (1 position)

[PN-UH551/UH501/UH431]
2
1) Peel off the tape.
<Note>
The Key angle is fastened together with the
rear cabinet with long screw.
The white tape serves as a temporary stop

2) Disconnect the connection (1 position).

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 12

 2 : ’18/Dec

3) Remove the hocks (5 positions) and remove the key PWB.

2

<Note>
When installing the key angle, insert the key angle into the hole of the main body.

<Note> [Only PN-UH501]

The rear cabinet have hooks.
When remove the rear cabinet and lift it, it may be lifted up with the key,
please remove the cabinet while holding key down.

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 13

 2 : ’18/Dec

6 IR PWB
[PN-UH861]
1) Remove the screw (1pc) and disconnect the connection (1 position).

<Note>
When assembling IR PWB, be sure to tighten the screw after connecting the cable
Don’t insert and remove cable when tightening or removing the screw to unit.

2) Remove the hooks (2 positions) and remove the IR PWB)

[PN-UH551/UH501/UH431]
2
1) Remove the screw (1pc) and disconnect the connection (1 position).

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 14

 2 : ’18/Dec

7. SPEAKER
[PN-UH861]
1) Remove the screws (2pcs) and disconnect the connection of the cable (1 position) for each speaker.

[PN-UH551/501/431]
2
1) Disconnect the connection of the cable (1 position) for each speaker.
<Note>
The speakers are fastened together with the rear cabinet with long screw.

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 15

 2 : ’18/Dec

8. LED DRIVER PWB

2 [PN-UH551/UH501]
1) Remove the screws (2pcs) and disconnect the support pin (2pcs) and disconnect the connection of the cables (2 positions)

[PN-UH431]
1) Remove the screws (4pcs) and disconnect the connection of the cables (2 positions).

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 16

9. LCD MODULE
[PN-UH861]
1) Remove Power PWB and Main PWB and Key PWB and IR PWB.
2) Remove 2 speakers ( x 2 screws) and 2 Stand fixing cover (Right/Left) ( x 8pcs)
and remove 4 brackets ( x 12 screws).

3) Remove 4 angles ( x 8screws) and remove Bezel L/R/TOP ( x 22 screws) and remove Bezel Bottom ( x 2 screws)

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 17

 2 : ’18/Dec

[PN-UH551/501/401]
2
1) Remove Power PWB and Main PWB and Key PWB and IR PWB and LED driver PWB and 2 speakers.
2) Remove 2 stand fixing angles (3 screws for each angle)

3) Remove Bezel bottom.

(PN-UH551) Remove the screws (6 pcs)

(PN-UH501) Remove the screws (7 pcs)

(PN-UH431) Remove the screws (6 pcs)

<Note>
When assemble the Bezel bottom,
there is a hook in the center of bezel bottom, so that the hook comes inside the main body.

PN-UH861/UH551/UH501/UH431 DISASSEMBLY AND ASSEMBLY 6 - 18

CHAPTER 7. TROUBLESHOOTING

1. HOW TO RESPOND BY TROUBLE SYMPTOM (IN CASE OF NON-DEFECTIVE MODE)

First of all, after confirming whether it is the symptom caused by installation environment or user setting, proceed to specifying the defect
location in the 2 section and subsequent items.
Defective symptom Action
No power. - Is the power code disconnected?
- Is the main power switch off?
There is no picture or sound. (The power LED is off)
- Is the power supplied to this monitor?
- Is the power code disconnected?
- Is the main power switch off?
(The power LED is lit in red)
- Is the monitor in standby mode?
(The power LED is flashing in green)
- If any external equipment is connected, make sure the equipment is operation (playing
back)
- Make sure correct input mode is selected.
- If note PC is connected, make sure whether it is set to the external output state.
Unstable video. - The signal may be incompatible.
- Try the automatic screen adjustment when D-SUB[RGB] is in use.
The video from the HDMI input terminal - Does the HDMI cable support 4K, and is it HDMI standard compliant?
does not appear properly. The monitor will not work with cables that are not standard compliant.
- Is the input signal compatible with this monitor?
- If the connected device does not support 4K, set HDMI MODE to MODE2.
The video from D-sub input terminal - Is the setting for D-SUB of INPUT SELECT on the SETUP menu correct?
does not appear properly. - Is the input signal compatible with this monitor?
Display is dark. - Make sure the external equipment is connected property.
There is a sound but no picture. - Make sure "BRIGHTNESS" of PICTURE menu is full on the "- (minus) side".
- "AUTO DIMMING" is displayed even if the brightness is adjusted, and if the brightness
cannot be adjusted, it is in a state of temperature abnormality.
- If note PC is connected, make sure whether it is set to the external output state.
- Make sure the power LED is flashing red and green alternately.
In this case, it is in a state of temperature abnormality.
There is a picture but no sound - Make sure the external equipment is connected property.
- Make sure the audio cable is connected property.
- Make sure the volume of the external equipment is set to minimum.
- Make sure the volume of Display is set to minimum or mute.
Sound from left and right speakers is - Are audio cables connected properly?
reserved.
Sound is heard from only one side.

PN-UH861/UH551/UH501/UH431 TROUBLESHOOTING 7- 1
 Defective symptom Action
Remote control does not work. - Are the batteries inserted with polarity (+,-) aligned?
- Are the batteries exhausted?
- Point the remote control unit toward the monitor’s remote control sensor.
- Is the menu display hidden or is operation disabled?
Control buttons do not work. - Load noises from outside may be interfering with normal operation. Turn off the power and
There is no picture. turn it on after waiting at least 5 seconds, and then check the operation.
It is displayed out of screen. - Make sure the scan mode is over scan.
The monitor makes a cracking sound. - You may occasionally hear a cracking sound from the monitor. This happens when the
cabinet slightly expands and contracts according to change in temperature. This does not
affect the monitor’s performance.
The power LED is flashing in red and - When the internal temperature of the monitor raises excessively, the brightness of the
green alternately. backlight decreases automatically in order to prevent high-temperature-related problems.
When “TEMPERATURE” is displayed in When this occurs, “TEMPERATURE” is displayed on the screen and the Power LED
the corner of the screen. flashes red and green alternately.
- If the internal temperature rises further, the monitor automatically enters standby mode.
(The Power LED continues flashing red and green alternately)
- Remove the cause of the excessive temperature rise.
- If the monitor enters standby mode due to a rise in temperature, to return to normal
display, turn the power switch off and then back on again. The monitor, however,
will enter standby mode again if the cause of the temperature rise is not eliminated.
- Check whether the monitor is placed at a location where a quick rise in temperature is
likely. Internal temperature rises quickly if the vents on the monitor are blocked.
- Internal temperature rises quickly if dust accumulates inside the monitor or around
the vents. Remove dust if possible.
When the “AUTO DIMMING” is - When the internal temperature of the monitor rises excessively, the brightness of the
displayed. backlight automatically decreases in order to prevent a further temperature rise. If you
attempt to adjust the brightness while the monitor is in this state. “AUTO DIMMING” is
displayed and you cannot change the brightness.
- Remove the cause of the excessive temperature rise.

[the power LED status]

Status Status of the monitor
Off Power off
Green lit Power on
Red lit Standby mode
Green flashing (at approx. 250ms interval) Updating by USB
Red flashing (at approx. 0.5s interval) Failure to update firmware
Red and Green flashing alternatively Temperature error
(at approx. 1s interval)

PN-UH861/UH551/UH501/UH431 TROUBLESHOOTING 7- 2
2. HOW TO RESPOND BY TROUBLE SYMPTOM (IN CASE OF DEFECTIVE MODE)

No Description
1 THE POWER IS NOT SUPPLIED (THE LED DOES NOT LIGHT UP)
2 THE REMOTE CONTROL DOES NOT WORK
3 THE DISPLAY DOES NOT WORK / DISPLAY ABNORMALITY
4 THE BACKLIGHT DOES NOT LIGHT UP
5 SOUND IS NOT OUTPUTTED / OUTPUT SOUND ABNORMALITY
6 CANNOT CONTROL LAN CONNECTION (LAN FOR DISPLAY)
7 CANNOT CONTROL RS-232C
8 THE LED LIGHTS UP IN ORDER RED TO GREEN (TEMPERATURE ERROR)

2-1. THE POWER IS NOT SUPPLIED (THE LED DOES NOT LIGHT UP)

2-2. THE REMOTE CONTROL DOES NOT WORK

2-3. THE DISPLAY DOES NOT WORK / DISPLAY ABNORMALITY

PN-UH861/UH551/UH501/UH431 TROUBLESHOOTING 7- 3
2-4. THE BACKLIGHT DOES NOT LIGHT UP

2-5. SOUND IS NOT OUTPUTTED / OUTPUT SOUND ABNORMALITY

2-6. CANNOT CONTROL LAN CONNECTION (LAN FOR DISPLAY)

PN-UH861/UH551/UH501/UH431 TROUBLESHOOTING 7- 4
2-7. CANNOT CONTROL RS-232C

2-8. THE LED LIGHTS UP IN ORDER RED TO GREEN (TEMPERATURE ERROR)

PN-UH861/UH551/UH501/UH431 TROUBLESHOOTING 7- 5
CHAPTER 8. HARDWARE DESCRIPTIONS

1. CIRCUIT DESCRIPTIONS
1-1. SYSTEM COMPONENT
This machine consists of LCD Module Unit / Main PWB / Power supply PWB / LED driver PWB / IR PWB / Key PWB / Speaker.

1-2. UNIT COMPOSITION

PARTS NAME FUNCTION
LCD module Display the video signal from Main PWB.
Main PWB Controls the video signals and outputs the each input video signal to the each resolution
signals to fit with the panel.
Power supply PWB Convert the power voltage from DC to AC and supply the power voltage to each PWB.
LED driver PWB Supply the power voltage to LED backlight.
IR PWB LED shows monitor status, Infrared receives control signals from Remote Controller.
Key PWB Outputs the key input from the bottom of the monitor as the electrical signals.
Speaker 10W x 2 Speaker

1-3. LCD MODULE

ITEM PN-UH861 PN-UH551 PN-UH501 PN-UH431
LCD 86V wide LCD 55V wide LCD 50V wide LCD 43V wide LCD
Screen size (Diagonal length) 217.426 cm 138.783 cm 125.730 cm 107.986 cm
Max. resolution 3840 x 2160
Max. colors 1.06 billion 1.07 billion
Pixel pitch (mm) 0.4935 (H) x 0.315 (H) x 0.2854 (H) x 0.2451 (H) x
0.4935 (V) 0.315 (V) 0.2854 (V) 0.2451 (W)
Max. brightness 400cd/㎡
Contrast ratio 1200 : 1 4000：1
Viewing angle 178 degree / 178 degree
Display Screen Size (mm) 1,895.04 (H) x 1,209.6 (H) x 1,095.84 (H) x 941.148 (H) x
1,065.96 (V) 680.4 (V) 616.41 (V) 529.416 (V)
Response Speed (Standard Value) 8 ms
Color Purity(NTSC Ratio) 68%
Backlight Edge LED Direct type LED
Backlight life 30,000 hours
(16 hours / 365 days)
Screen uniformity 60% 71%
Manufacturer LG TPV
(LCD panel and T-con PWB : AUO)

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-1

1-4. MAIN PWB
INPUT / OUTPUT TERMINAL CONTENTS
Input terminal Antenna / Cable x 1 (75Ω Unbalance, F Type x 1, ANALOG(VHF,UHF,CATV)/DIGITAL))
Mini D-sub 15 pins x 1 Analog terminal (Mini D-sub 15 pins) (Supporting RGB signal)
HDMI x 1(Supporting HDMI2.0 / HDCP2.2 / HDMI CEC) (Supporting PC/AV signal)
Audio x 1 φ3.5mm mini stereo jack terminal
RS-232C (Interactive) x 1 D-sub9 pin
USB (Type A) x 1 （for media player・firmware update）
Output terminal IR Pass Through x 1 D-sub9 pin
Audio x 1 RCA (L/R) Audio output terminal
Input / Output LAN (interactive) x 1 (RJ45)（for display control）
terminal

1-5. DETECT ABNORMAL TEMPERATURE

This function is monitoring the inner temperature continuously, and if detect abnormal temperature, then notify to a user and control the
monitor behavior. There is a temperature sensor connected in the monitor, and monitoring its value.
The sensor has a threshold value to notify high temperature, control dimming the brightness, and control turning off the monitor. Observe
temperature every a minute, and when the value becomes the threshold temperature and over , and it continues 3 times in a row, each
control is executed.
This monitor judge to rise the inside temperature, then the brightness go down. If the situation escalate more, this monitor power off.
TEMPERATURE STATUS CONTROL
Abnormal temperature Display alert OSD on the screen, and notify.
notification Notifying by Red / Green LED blinks.
Limit backlight brightness When the inner temperature is risen, it prevents the temperature rise by dimming the brightness of the
panel.
The control of power-off If there is no effect of dimming brightness and the temperature over the threshold, the display power-off
for safety.
Save the date / time and the temperature to log if abnormal temperature occurs.

If the display can’t get sensor value 3 times in arrow because of the sensor disconnection, crash etc., it regards the failure of the sensor.
In this case, the following operation restriction and notification of abnormity are executed.
- Brightness is dimmed forcibly (because it can’t get sensor temperature).
- Display alert OSD on screen and notify user of abnormality.
- Blink LED in red and green by 1 second alternately and notice user the abnormity.
Once the failure of the sensor occurred, the malfunction state continues until the power [ON] even if the sensor recovered.
The crashed temperature sensor if displayed as [ERR] on the service menu and [126℃] in the command.

The temperature threshold is as follows.

NORTIFICATION OF HIGH TEMPERATURE/ POWER OFF
BRIGHTNESS CONTROL
PN-UH861 63 68
PN-UH551
PN-UH501 60 65
PN-UH431

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-2

2. BLOCK DIAGRAM

■ PN-UH861 Block Diagram ・・・ Page 8-4

■ PN-UH551 Block Diagram ・・・ Page 8-5

■ PN-UH501 Block Diagram ・・・ Page 8-6

■ PN-UH431 Block Diagram ・・・ Page 8-7

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-3

■ PN-UH861 Block Diagram

Power Supply Board (715G7883) I/F Board (G9984-M0A-B00-0040)

Q702 U704
5V_s +5V_Normal 5V_s 3.3V_s +3.3V_Standby
P-MOSFET Regulator
AO4449 AZ1117CH-3.3TRG1
ALPHA&OMEGA Diodes

PS_ON +3.3V_Standby
U710
Standby 16V 16V 16V 16V 5V_s +5V_Standby
AC Filter Rectifier PFC Regulator
Power
Inlet Circuit Circuit Circuit SY8366QNC
Circuit 16V 16V_AUD 16V_AUD
CN9101 CN701 Silergy
BL_ON MAIN MAIN U702
POWER BL_ON / BL_DIM POWER BL_ON / BL_DIM BL_ON / BL_DIM +1.15V_DDRC 5V_s
BL_DIM Regulator
16P 16P AT1529F11U
PS_ON PS_ON PS_ON PS_ON GMT

Main
Power 16V_AUD 5V_s U105 5V_s
Circuit VSYNC Schmitt VSYNC CN101
U601 Inverter VGA IN
LOUT +/- I2C_SDA / SCL HSYNC HSYNC VSYNC / HSYNC
Digital 74HC14D 15P
CN602 ROUT +/-
Audio TOSHIBA
LR +/- AU_SD / WS / BCK / MCK AU_SD / WS / BCK / MCK
Amplifier
4P
AD87588-LG48NAY
ESMT
RS-232
5V_s 3.3V_s U407 RX / TX
BL_ON BL_ON CN406
24V 24V RS-232 RS-232 Level Shifter
BL_DIM BL_DIM U102 D-SUB
5V 5V RX / TX MAX3232CPWR
Switch 9P
TI
CN9402 CN9401 CN103 G5250H1T1U
LED Control LED Control USB2.0 GMT
14P 14P 4P USB1_D+/- USB1_D+/-
5V_s
U408
SDA
Switch
BL_DIM SN74LVC1G3157DCKR
BL_ON

U103 U403 TI
3.3V 5V Switch
Regulator
U3001 AZ1117CH-3.3TRG1 74HC4052PW
24V 24V Thermal Sendor Diodes 5V_s
LM75BDP DEBUG U409
I2C_SDA / SCL
NXP _ON Switch
CN102 CN101 SN74LVC1G3157DCKR
LED Drive LED Control
12P
LED Control
14P
I2C_SDA / SCL
UART_SW SCL
TI

Board IC102
Regulator
IC101
Regulator U101
3.3V
UART LAN
SJ1117-33F SJ1117-50F ANT I2C_SDA / SCL RX / TX RX / TX CN301
FCN101 Tuner
3.3V LAN
ANT Si2151-A10-GMR
DIFP / DIFM / AGC DIFP / DIFM / AGC 4P
5V SILICON LABS

24V 24V
3.3V_s
BL_DIM
3.3V_s CN401
BL_ON
CN800 UART_RX / TX MSTV
CLK / CS 4P
I2C_S Port I2C_SDA / SCL
MISO 4P
MOSI
U401
SoC
MSD91H1BN2 LINEIN_L / R LINEIN_L / R CN405
IC501 MStar AUDIO IN
DC/DC

DC/DC

DC/DC

DC/DC

FB IC302 FB FB IC301 FB 5V
u-con S3EPLQFP 156P
AS3820 AS3820 3P
MC93F5516
dialog[AMS] [AMS]
ABOV
CN803
Scan BL VSYNC / SCL / SDO / SDI / CS_SBL 3.3V_s 3.3V_s
DIN U406
12P IR_OUT CN407
CLK Bus buffer
VLED

VLED

IR_IN D-SUB
VLED 6ch 6ch 6ch 6ch VLED VSYNC 74LVC1G125GV
9P
nexperia
CN603 U306 HDMI0 HDMI0
CN304 CN303 CN302 CN301
FFC I2C-bus RXnN / CLKN RXnN / CLKN
8P 8P 8P 8P MCU_
4P PCA9554PW RXnP / CLKP RXnP / CLKP
ISPM_CTL NXP CN501
LN232_ U302 HPD HPD HDMI&ARC
FFC FFC FFC FFC RX2 ARM
CN302 RESETn 19P
8P 8P 8P 8P TX W7500
LN232
WIZnet HDMI2 HDMI2
4P
CN? CN? CN? CN? RXnN / CLKN RXnN / CLKN
8P 8P 8P 8P RXnP / CLKP RXnP / CLKP CN503
HPD HPD HDMI2
TXP LAN PD_CTL 19P
VLED

VLED

VLED

VLED

6ch 6ch 6ch 6ch TXN 3.3V_s

CN303 RXP SPI_ U402
U301
RXN U303 CSN / WP
RJ45/LED LAN 3.3V 5V_s FLASH
Regulator SDI / SDO / CLK
LED LED LED LED 15P RTL8201F-VB-CG MX25L6436FM2I-08G
AT1529F11U
bar bar bar bar REALTEK
GMT
11 11 11 11 3.3V_s
series series series series FFC U410
4P 5V_s
U703 Q702 Reset IC
+1.8V_DDR2 5V_DDRV System_RST G690H293T73
Regulator P-MOSFET
HSYNC_SBL

DDRV_ON GMT
AZ1117CH-3.3TRG1 AO3401A
Diodes ALPHA&OMEGA
LED Backlight +1.8V_DDR2
EAR_L / R EAR_L / R CN601
RCA JACK
4P
VB1 VB1

LCD Pannel U801A/B/C/D

UART2_TX
U802
VGA_L /R _in VGA_L /R _in CN405
VGA
FLASH
3P
MX25L3236FM2I-08G
MST7484GC
MACRONIX
SPI_
CZ / CK IR-in / KEYn-in / LED_RE / LED_G IR-in / KEYn-in / LED_RE / LED_G
VB1 VB1 DO / DI
VCC3.3V_FRC CN105
Key/IR/LED
I2C_SDA / SCL 14P

CN? U806
T-CON Board FFC
4P
Regulator
G1117-33T63Uf
5V

GMT

12V_
CN? 12V CN802
Panel U808
12V-Panel 12V-Panel VCC1.8V_FRC 5V
Regulator
CN? 5P 5P
SY8009BABC
VB1
Silergy
51P
VB1
CN408 5V
VB1 U809
VB1 (SoC) 12V_Panel VCC0.9V_FRC
51P Regulator
51P 16V
SY8366QNC
Silergy
CN?
VB1 VB1
51P CN? CN801
VB1 U701
VB1 (FRC) VB1 (FRC) 12V_Panel 12V_Panel 16V
51P Regulator
51P 51P
SY8366QNC
Silergy

FRC Board

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-4

61
■ PN-UH551 Block Diagram

Power Supply Board (715G9384) I/F Board (G9984-M0A-B00-0040)

Q702 U704
5V_s +5V_Normal 5V_s 3.3V_s +3.3V_Standby
P-MOSFET Regulator
AO4449 AZ1117CH-3.3TRG1
ALPHA&OMEGA Diodes

PS_ON +3.3V_Standby
PN_ON=L : 13V
PS_ON=H : 16V U710
16V 16V 16V 5V_s +5V_Standby
AC Filter Rectifier PFC Power Regulator
Inlet Circuit Circuit Circuit Circuit SY8366QNC
16V_AUD 16V_AUD Silergy
CN9101 CN701
BL_ON MAIN MAIN U702
POWER BL_ON / BL_DIM POWER BL_ON / BL_DIM BL_ON / BL_DIM +1.15V_DDRC 5V_s
BL_DIM Regulator
16P 16P AT1529F11U
PS_ON PS_ON PS_ON PS_ON GMT

Power
Circuit 16V_AUD 5V_s U105 5V_s
VSYNC Schmitt VSYNC CN101
U601 Inverter VGA IN
LOUT +/- I2C_SDA / SCL HSYNC HSYNC VSYNC / HSYNC
Digital 74HC14D 15P
CN602 ROUT +/-
U8604 Audio TOSHIBA
LR +/- AU_SD / WS / BCK / MCK AU_SD / WS / BCK / MCK
Regulator Amplifier
4P
AS78L12RTR-G1 AD87588-LG48NAY
VLED Diodes ESMT
43" : 16.25V RS-232
50" : 19.7V 5V_s 3.3V_s U407 RX / TX
BL_ON CN406
55" : 22.1V FB 12V RS-232 RS-232 Level Shifter
BL_DIM U102 D-SUB
5V 5V RX / TX MAX3232CPWR
Switch 9P
TI
CN8601 CN103 G5250H1T1U
LED Control USB2.0 GMT
14P 4P USB1_D+/- USB1_D+/-
5V_s
U408
SDA
Switch
SN74LVC1G3157DCKR
BL_DIM
BL_ON

U103 U403 TI
VLED x5 FB 12V 3.3V 5V
Regulator Switch
U3001 AZ1117CH-3.3TRG1 74HC4052PW
Thermal Sendor Diodes 5V_s
LM75BDP DEBUG U409
I2C_SDA / SCL
NXP _ON Switch
CN101 SN74LVC1G3157DCKR
LED Drive LED Control I2C_SDA / SCL TI
14P UART_SW SCL
Board 3.3V
VLED FB 12V BL_ON BL_DIM UART LAN
(715G8492) FCN101
ANT
U101
Tuner
I2C_SDA / SCL RX / TX RX / TX CN301
LAN
ANT Si2151-A10-GMR
DIFP / DIFM / AGC DIFP / DIFM / AGC 4P
SILICON LABS

3.3V_s
3.3V_s CN401
CN800 UART_RX / TX MSTV
I2C_S Port I2C_SDA / SCL 4P
4P
IC? IC? IC? IC? U401
PF7713 PF7713 PF7713 PF7713 SoC
powerforest powerforest powerforest powerforest MSD91H1BN2 LINEIN_L / R LINEIN_L / R CN405
5V MStar AUDIO IN
S3EPLQFP 156P 3P

VLED x8 4ch 4ch 4ch 4ch

CN803
Scan BL VSYNC / SCL / SDO / SDI / CS_SBL 3.3V_s 3.3V_s
U406
CN? IR_OUT CN407
12P Bus buffer
24P IR_IN D-SUB
74LVC1G125GV
9P
nexperia
U306 HDMI0 HDMI0
I2C-bus RXnN / CLKN RXnN / CLKN
MCU_ PCA9554PW RXnP / CLKP RXnP / CLKP CN501
VLED x7 4ch 4ch 4ch 2ch ISPM_CTL NXP
LN232_ U302 HPD HPD HDMI&ARC
RX2 ARM 19P
CN302 RESETn
TX W7500
LN232
WIZnet HDMI2 HDMI2
4P
CN? RXnN / CLKN RXnN / CLKN
24P RXnP / CLKP RXnP / CLKP CN503
HPD HPD HDMI2
TXP LAN PD_CTL 19P
VLED 2ch VLED 2ch TXN 3.3V_s
CN303 RXP SPI_ U402
U301
RXN U303 CSN / WP
RJ45/LED LAN 3.3V 5V_s FLASH
Regulator SDI / SDO / CLK
15P RTL8201F-VB-CG MX25L6436FM2I-08G
AT1529F11U
LED LED REALTEK
GMT
bar Total 7 bars bar
3.3V_s
7 7 U410
5V_s
series series U703 Q702 Reset IC
+1.8V_DDR2 5V_DDRV System_RST G690H293T73
Regulator P-MOSFET
HSYNC_SBL

DDRV_ON GMT
AZ1117CH-3.3TRG1 AO3401A
Diodes ALPHA&OMEGA
EAR_L / R EAR_L / R CN601
+1.8V_DDR2 RCA JACK
LED Backlight VB1 VB1
4P

UART2_TX VGA_L /R _in VGA_L /R _in CN405

U802
U801A/B/C/D VGA
FLASH
3P
MX25L3236FM2I-08G
MST7484GC
MACRONIX
LCD Pannel SPI_
CZ / CK IR-in / KEYn-in / LED_RE / LED_G IR-in / KEYn-in / LED_RE / LED_G
VB1 VB1 DO / DI
VCC3.3V_FRC CN105
Key/IR/LED
I2C_SDA / SCL 14P

U806
5V
Regulator
G1117-33T63Uf
T-CON Board GMT

12V_
CN? 12V CN802
Panel U808
12V-Panel 12V-Panel VCC1.8V_FRC 5V
Regulator
CN? 5P 5P
SY8009BABC
VB1
Silergy
51P
VB1
CN408 5V
VB1 U809
VB1 (SoC) 12V_Panel VCC0.9V_FRC
51P Regulator
51P 16V
SY8366QNC
Silergy
CN?
VB1 VB1
51P CN? CN801
VB1 U701
VB1 (FRC) VB1 (FRC) 12V_Panel 12V_Panel 16V
51P Regulator
51P 51P
SY8366QNC
Silergy

FRC Board

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-5

62
■ PN-UH501 Block Diagram

Power Supply Board (715G9384) I/F Board (G9984-M0A-B00-0040)

Q702 U704
5V_s +5V_Normal 5V_s 3.3V_s +3.3V_Standby
P-MOSFET Regulator
AO4449 AZ1117CH-3.3TRG1
ALPHA&OMEGA Diodes

PS_ON +3.3V_Standby
PN_ON=L : 13V
PS_ON=H : 16V U710
16V 16V 16V 5V_s +5V_Standby
AC Filter Rectifier PFC Power Regulator
Inlet Circuit Circuit Circuit Circuit SY8366QNC
16V_AUD 16V_AUD Silergy
CN9101 CN701
BL_ON MAIN MAIN U702
POWER BL_ON / BL_DIM POWER BL_ON / BL_DIM BL_ON / BL_DIM +1.15V_DDRC 5V_s
BL_DIM Regulator
16P 16P AT1529F11U
PS_ON PS_ON PS_ON PS_ON GMT

Power
Circuit 16V_AUD 5V_s U105 5V_s
VSYNC Schmitt VSYNC CN101
U601 Inverter VGA IN
LOUT +/- I2C_SDA / SCL HSYNC HSYNC VSYNC / HSYNC
Digital 74HC14D 15P
CN602 ROUT +/-
U8604 Audio TOSHIBA
LR +/- AU_SD / WS / BCK / MCK AU_SD / WS / BCK / MCK
Regulator Amplifier
4P
AS78L12RTR-G1 AD87588-LG48NAY
VLED Diodes ESMT
43" : 16.25V RS-232
50" : 19.7V 5V_s 3.3V_s U407 RX / TX
BL_ON CN406
55" : 22.1V FB 12V RS-232 RS-232 Level Shifter
BL_DIM U102 D-SUB
5V 5V RX / TX MAX3232CPWR
Switch 9P
TI
CN8601 CN103 G5250H1T1U
LED Control USB2.0 GMT
14P 4P USB1_D+/- USB1_D+/-
5V_s
U408
SDA
Switch
SN74LVC1G3157DCKR
BL_DIM
BL_ON

U103 U403 TI
VLED x5 FB 12V 3.3V 5V
Regulator Switch
U3001 AZ1117CH-3.3TRG1 74HC4052PW
Thermal Sendor Diodes 5V_s
LM75BDP DEBUG U409
I2C_SDA / SCL
NXP _ON Switch
CN101 SN74LVC1G3157DCKR
LED Drive LED Control I2C_SDA / SCL TI
14P UART_SW SCL
Board 3.3V
VLED FB 12V BL_ON BL_DIM UART LAN
(715G8492) FCN101
ANT
U101
Tuner
I2C_SDA / SCL RX / TX RX / TX CN301
LAN
ANT Si2151-A10-GMR
DIFP / DIFM / AGC DIFP / DIFM / AGC 4P
SILICON LABS

3.3V_s
3.3V_s CN401
CN800 UART_RX / TX MSTV
I2C_S Port I2C_SDA / SCL 4P
4P
IC? IC? IC? IC? U401
PF7713 PF7713 PF7713 PF7713 SoC
powerfores] powerforest powerforest powerfores] MSD91H1BN2 LINEIN_L / R LINEIN_L / R CN405
5V MStar AUDIO IN
S3EPLQFP 156P 3P

VLED x8 4ch 4ch 4ch 4ch

CN803
Scan BL VSYNC / SCL / SDO / SDI / CS_SBL 3.3V_s 3.3V_s
U406
CN? IR_OUT CN407
12P Bus buffer
24P IR_IN D-SUB
74LVC1G125GV
9P
nexperia
U306 HDMI0 HDMI0
I2C-bus RXnN / CLKN RXnN / CLKN
MCU_ PCA9554PW RXnP / CLKP RXnP / CLKP CN501
VLED x6 4ch 4ch 4ch ISPM_CTL NXP
LN232_ U302 HPD HPD HDMI&ARC
RX2 ARM 19P
CN302 RESETn
TX W7500
LN232
WIZnet HDMI2 HDMI2
4P
CN? RXnN / CLKN RXnN / CLKN
24P RXnP / CLKP RXnP / CLKP CN503
HPD HPD HDMI2
TXP LAN PD_CTL 19P
VLED 2ch VLED 2ch TXN 3.3V_s
CN303 RXP SPI_ U402
U301
RXN U303 CSN / WP
RJ45/LED LAN 3.3V 5V_s FLASH
Regulator SDI / SDO / CLK
15P RTL8201F-VB-CG MX25L6436FM2I-08G
AT1529F11U
LED LED REALTEK
GMT
bar Total 6 bars bar
3.3V_s
6 6 U410
5V_s
series series U703 Q702 Reset IC
+1.8V_DDR2 5V_DDRV System_RST G690H293T73
Regulator P-MOSFET
HSYNC_SBL

DDRV_ON GMT
AZ1117CH-3.3TRG1 AO3401A
Diodes ALPHA&OMEGA
EAR_L / R EAR_L / R CN601
+1.8V_DDR2 RCA JACK
LED Backlight VB1 VB1
4P

UART2_TX VGA_L /R _in VGA_L /R _in CN405

U802
U801A/B/C/D VGA
FLASH
3P
MX25L3236FM2I-08G
MST7484GC
MACRONIX
LCD Pannel SPI_
CZ / CK IR-in / KEYn-in / LED_RE / LED_G IR-in / KEYn-in / LED_RE / LED_G
VB1 VB1 DO / DI
VCC3.3V_FRC CN105
Key/IR/LED
I2C_SDA / SCL 14P

U806
5V
Regulator
G1117-33T63Uf
T-CON Board GMT

12V_
CN? 12V CN802
Panel U808
12V-Panel 12V-Panel VCC1.8V_FRC 5V
Regulator
CN? 5P 5P
SY8009BABC
VB1
Silergy
51P
VB1
CN408 5V
VB1 U809
VB1 (SoC) 12V_Panel VCC0.9V_FRC
51P Regulator
51P 16V
SY8366QNC
Silergy
CN?
VB1 VB1
51P CN? CN801
VB1 U701
VB1 (FRC) VB1 (FRC) 12V_Panel 12V_Panel 16V
51P Regulator
51P 51P
SY8366QNC
Silergy

FRC Board

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-6

63
■ PN-UH431 Block Diagram

Power Supply Board (715G9384) I/F Board (G9984-M0A-B00-0040)

Q702 U704
5V_s +5V_Normal 5V_s 3.3V_s +3.3V_Standby
P-MOSFET Regulator
AO4449 AZ1117CH-3.3TRG1
ALPHA&OMEGA Diodes

PS_ON +3.3V_Standby
PN_ON=L : 13V
PS_ON=H : 16V U710
16V 16V 16V 5V_s +5V_Standby
AC Filter Rectifier PFC Power Regulator
Inlet Circuit Circuit Circuit Circuit SY8366QNC
16V_AUD 16V_AUD Silergy
CN9101 CN701
BL_ON MAIN MAIN U702
POWER BL_ON / BL_DIM POWER BL_ON / BL_DIM BL_ON / BL_DIM +1.15V_DDRC 5V_s
BL_DIM Regulator
16P 16P AT1529F11U
PS_ON PS_ON PS_ON PS_ON GMT

Power
Circuit 16V_AUD 5V_s U105 5V_s
VSYNC Schmitt VSYNC CN101
U601 Inverter VGA IN
LOUT +/- I2C_SDA / SCL HSYNC HSYNC VSYNC / HSYNC
Digital 74HC14D 15P
CN602 ROUT +/-
U8604 Audio TOSHIBA
LR +/- AU_SD / WS / BCK / MCK AU_SD / WS / BCK / MCK
Regulator Amplifier
4P
AS78L12RTR-G1 AD87588-LG48NAY
VLED Diodes ESMT
43" : 16.25V RS-232
50" : 19.7V 5V_s 3.3V_s U407 RX / TX
BL_ON CN406
55" : 22.1V FB 12V RS-232 RS-232 Level Shifter
BL_DIM U102 D-SUB
5V 5V RX / TX MAX3232CPWR
Switch 9P
TI
CN8601 CN103 G5250H1T1U
LED Control USB2.0 GMT
14P 4P USB1_D+/- USB1_D+/-
5V_s
U408
SDA
Switch
SN74LVC1G3157DCKR
BL_DIM
BL_ON

U103 U403 TI
VLED x5 FB 12V 3.3V 5V
Regulator Switch
U3001 AZ1117CH-3.3TRG1 74HC4052PW
Thermal Sendor Diodes 5V_s
LM75BDP DEBUG U409
I2C_SDA / SCL
NXP _ON Switch
CN101 SN74LVC1G3157DCKR
LED Drive LED Control I2C_SDA / SCL TI
14P UART_SW SCL
Board 3.3V
VLED FB 12V BL_ON BL_DIM UART LAN
(715G8492) FCN101
ANT
U101
Tuner
I2C_SDA / SCL RX / TX RX / TX CN301
LAN
ANT Si2151-A10-GMR
DIFP / DIFM / AGC DIFP / DIFM / AGC 4P
SILICON LABS

3.3V_s
3.3V_s CN401
CN800 UART_RX / TX MSTV
I2C_S Port I2C_SDA / SCL 4P
4P
IC? IC? IC? IC? U401
PF7713 PF7713 PF7713 PF7713 SoC
powerforest powerforest powerfores] powerforest MSD91H1BN2 LINEIN_L / R LINEIN_L / R CN405
5V MStar AUDIO IN
S3EPLQFP 156P 3P

VLED x8 4ch 4ch 4ch 4ch

CN803
Scan BL VSYNC / SCL / SDO / SDI / CS_SBL 3.3V_s 3.3V_s
U406
CN? IR_OUT CN407
12P Bus buffer
24P IR_IN D-SUB
74LVC1G125GV
9P
nexperia
U306 HDMI0 HDMI0
I2C-bus RXnN / CLKN RXnN / CLKN
MCU_ PCA9554PW RXnP / CLKP RXnP / CLKP CN501
VLED x5 4ch 4ch 2ch ISPM_CTL NXP
LN232_ U302 HPD HPD HDMI&ARC
RX2 ARM 19P
CN302 RESETn
TX W7500
LN232
WIZnet HDMI2 HDMI2
4P
CN? RXnN / CLKN RXnN / CLKN
8P RXnP / CLKP RXnP / CLKP CN503
HPD HPD HDMI2
TXP LAN PD_CTL 19P
VLED 2ch VLED 2ch TXN 3.3V_s
CN303 RXP SPI_ U402
U301
RXN U303 CSN / WP
RJ45/LED LAN 3.3V 5V_s FLASH
Regulator SDI / SDO / CLK
15P RTL8201F-VB-CG MX25L6436FM2I-08G
AT1529F11U
LED LED REALTEK
GMT
bar Total 5 bars bar
3.3V_s
5 5 U410
5V_s
series series U703 Q702 Reset IC
+1.8V_DDR2 5V_DDRV System_RST G690H293T73
Regulator P-MOSFET
HSYNC_SBL

DDRV_ON GMT
AZ1117CH-3.3TRG1 AO3401A
Diodes ALPHA&OMEGA
EAR_L / R EAR_L / R CN601
+1.8V_DDR2 RCA JACK
LED Backlight VB1 VB1
4P

UART2_TX VGA_L /R _in VGA_L /R _in CN405

U802
U801A/B/C/D VGA
FLASH
3P
MX25L3236FM2I-08G
MST7484GC
MACRONIX
LCD Pannel SPI_
CZ / CK IR-in / KEYn-in / LED_RE / LED_G IR-in / KEYn-in / LED_RE / LED_G
VB1 VB1 DO / DI
VCC3.3V_FRC CN105
Key/IR/LED
I2C_SDA / SCL 14P

U806
5V
Regulator
G1117-33T63Uf
T-CON Board GMT

12V_
CN? 12V CN802
Panel U808
12V-Panel 12V-Panel VCC1.8V_FRC 5V
Regulator
CN? 5P 5P
SY8009BABC
VB1
Silergy
51P
VB1
CN408 5V
VB1 U809
VB1 (SoC) 12V_Panel VCC0.9V_FRC
51P Regulator
51P 16V
SY8366QNC
Silergy
CN?
VB1 VB1
51P CN? CN801
VB1 U701
VB1 (FRC) VB1 (FRC) 12V_Panel 12V_Panel 16V
51P Regulator
51P 51P
SY8366QNC
Silergy

FRC Board

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-7

64
3. CONNECTOR TABLE

■ PN-UH861 Connector Table・・・ Page 8-9

■ PN-UH551 Connector Table・・・ Page 8-10

■ PN-UH501 Connector Table・・・ Page 8-11

■ PN-UH431 Connector Table・・・ Page 8-12

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-4

PN-UH861

Power Supply pwb I/F pwb T-CON pwb

CN9101 CN701 CN801 CN2

Symbol Pin No. Pin No. Symbol BL_ON Pin No. Pin No.
44-51 pin
DIM 16 16 BL_ON 51 1
PANEL_ON/OFF 15 15 BL_DIM BL_DIM ： V-by-One ：
PS_ON PS_ON/OFF 14 14 NC 1 51
NC 13 13 PS_ON PS_ON FRC
GND 12 12 GND
GND 11 11 GND
GND 10 10 GND
GND 9 9 GND
16V2 +16V2_AL 8 8 +16V_AUD 16V_AUD
PN_ON=L : 0V +16V2_AL 7 7 +16V_AUD
PS_ON=H : 16V +16V_SSB 6 6 +16V 16V
+16V_SSB 5 5 +16V CN408
+16V_SSB 4 4 +16V Pin No.
44-51 pin
16V +16V_SSB 3 3 +16V 51
+16V2_A 2 2 NC ：
+16V2_A 1 1 NC 1
PANEL_ON/OFF DC/DC VCC0.9V_FRC

CN802 CN1
16V 12V Symbol Pin No. Pin No. Symbol
DC/DC 12V-Panel 5 1 12V-Panel 12V
12V-Panel 4 2 12V-Panel
12V-Panel 3 3 12V-Panel
GND 2 4 GND
16V GND 1 5 GND

DC/DC

DC/DC VCC1.8V_FRC
+5V_Standby
CN803
DC/DC VCC3.3V_FRC Symbol Pin No.
PS_ON NC 12
NC 11
FB VCC5V_FRC NC 10
GND 9
+5V_Normal 8
SDO_SBL 7
SCL_SBL 6
DC/DC +1.15V_VDDC SDI_SBL 5
GND 4
CS_SBL 3
DC/DC 3.3V_Standby HSYNC_SBL 2
VSYNC_SBL 1

5V_DDRV

DC/DC +1.8V_DDR2

LED Driver pwb

CN603 FFC CN6

Symbol Pin No. Pin No. Symbol
IC102

3.3V
VSYNC 4 1 VSYNC
IC501
CLK /CS u-con
GND 3
FFC
2 GND
MC93F5516 DIN 2 3 DIN
MISO DCLK 1 4 DCLK

MOSI

DC/DC
CN301 FFC
Symbol Pin No.
FB1 Anode 8
NC 7
Cathode 6
CN9402 Cathode 5
Symbol Pin No. Cathode 4
NC 18 Cathode 3
NC 17 Cathode 2
PANEL_ON/OFF 16 CN101 Cathode 1
DIM 15 Pin No. Symbol IC301
NC 14 14 PWM LED
NC 13 13 NC Drive IC CN302 FFC
GND 12 12 BL on/off AS3820 Symbol Pin No.
GND 11 11 STATUS Cathode 8
GND 10 10 GND Cathode 7
GND 9 9 GND Cathode 6
IC101

5V
GND 8 8 GND Cathode 5
GND 7 7 GND Cathode 4
+24V 6 6 GND Cathode 3
PN_ON=L : 0V +24V 5 5 +24V NC 2
PS_ON=H : 24V +24V 4 4 +24V FB2 Anode 1
+24V 3 3 +24V
+24V 2 2 +24V Q1
DC/DC
+24V 1 1 +24V

DC/DC
CN303 FFC
Symbol Pin No.
FB1 Anode 8
NC 7
Cathode 6
CN9401 Cathode 5
Symbol Pin No. Cathode 4
NC 18 Cathode 3
NC 17 Cathode 2
PANEL_ON/OFF 16 Cathode 1
DIM 15 IC302
NC 14 CN102 LED
NC 13 Pin No. Symbol Drive IC CN304 FFC
GND 12 12 NC AS3820 Symbol Pin No.
GND 11 11 NC Cathode 8
GND 10 10 GND Cathode 7
GND 9 9 GND Cathode 6
5V
GND 8 8 GND Cathode 5
GND 7 7 GND Cathode 4
24V +24V 6 6 GND Cathode 3
PN_ON=L : 0V +24V 5 5 +24V NC 2
PS_ON=H : 24V +24V 4 4 +24V FB2 Anode 1
+24V 3 3 +24V
+24V 2 2 +24V Q2
DC/DC
+24V 1 1 +24V

AC Inlet

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8-9

PN-UH551

Power Supply pwb I/F pwb T-CON pwb

CN9101 CN701 CN801 J104

Symbol Pin No. Pin No. Symbol BL_ON Pin No. Pin No.
44-51 pin
DIM 16 16 BL_ON 51 1
BL_ON/OFF 15 15 BL_DIM BL_DIM ： V-by-One ：
PS_ON PS_ON/OFF 14 14 NC 1 51
COMP 13 13 PS_ON PS_ON
GND 12 12 GND
GND 11 11 GND
GND 10 10 GND
PN_ON=L : 13V GND 9 9 GND
PS_ON=H : 16V 16V2 8 8 +16V_AUD 16V_AUD
16V2 7 7 +16V_AUD
16V 16V 6 6 +16V 16V
16V 5 5 +16V CN408
16V 4 4 +16V Pin No.
44-51 pin
16V 3 3 +16V 51
NC 2 2 NC ：
NC 1 1 NC 1
PANEL_ON/OFF DC/DC VCC0.9V_FRC

CN802 (N.M.)
16V 12V Symbol Pin No.
DC/DC 12V-Panel 5
12V-Panel 4
12V-Panel 3
GND 2
16V GND 1

DC/DC

DC/DC VCC1.8V_FRC
+5V_Standby
CN803
DC/DC VCC3.3V_FRC Symbol Pin No.
PS_ON NC 12
NC 11
FB VCC5V_FRC NC 10
GND 9
+5V_Normal 8
SDO_SBL 7
SCL_SBL 6
DC/DC +1.15V_VDDC SDI_SBL 5
GND 4
CS_SBL 3
DC/DC 3.3V_Standby HSYNC_SBL 2
VSYNC_SBL 1

5V_DDRV

DC/DC +1.8V_DDR2

LED Driver pwb LED Back Light

43" : 16.25V
50" : 19.7V CN8601 CN8606 CN8605
55" : 22.1V Symbol Pin No. Pin No. Symbol Symbol Pin No. Pin No. Symbol
19.5V circuit +19.5V 14 1 Vin VLED 1 1 Anode
+19.5V 13 2 Vin VLED 2 2 Anode
PN_ON=L : 0V +19.5V 12 3 Vin VLED 3 3 Anode
PS_ON=H : 19.5V +19.5V 11 4 Vin VLED 4 4 Anode 7 strings
+19.5V 10 5 Vin VLED 5 5 Anode
GND 9 6 GND VLED 6 6 Anode
GND 8 7 GND VLED 7 7 Anode
7 series
GND 7 8 GND VLED 8 8 NC
GND 6 9 GND LED FB16 9 9 NC
GND 5 10 GND Drive IC FB15 10 10 NC
DIM 4 11 ON/OFF PF7713 FB14 11 11 Cathode 14
16V 12V BL ON/OFF 3 12 DIM U8804 FB13 12 12 Cathode 13
Regulator DB Vcc 2 13 VCC LED FB12 13 13 Cathode 12
COMP 1 14 COMP Drive IC FB11 14 14 Cathode 11
PF7713 FB10 15 15 Cathode 10
AC Inlet U8803 FB09 16 16 Cathode 09
LED FB08 17 17 Cathode 08 14 strings
Drive IC FB07 18 18 Cathode 07
PF7713 FB06 19 19 Cathode 06
7 series
U8802 FB05 20 20 Cathode 05
LED FB04 21 21 Cathode 04
Drive IC FB03 22 22 Cathode 03
PF7713 FB02 23 23 Cathode 02
U8801 FB01 24 24 Cathode 01

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8 - 10

PN-UH501

Power Supply pwb I/F pwb

CN9101 CN701 CN801

Symbol Pin No. Pin No. Symbol BL_ON Pin No.
44-51 pin
DIM 16 16 BL_ON 51
BL_ON/OFF 15 15 BL_DIM BL_DIM ：
PS_ON PS_ON/OFF 14 14 NC 1
COMP 13 13 PS_ON PS_ON FRC
GND 12 12 GND
GND 11 11 GND
GND 10 10 GND
PN_ON=L : 13V GND 9 9 GND
PS_ON=H : 16V 16V2 8 8 +16V_AUD 16V_AUD
T-CON pwb
16V2 7 7 +16V_AUD
16V 16V 6 6 +16V 16V
16V 5 5 +16V CN408 J104
16V 4 4 +16V Pin No. Pin No.
44-51 pin
16V 3 3 +16V 51 1
NC 2 2 NC ： V-by-One ：
NC 1 1 NC 1 51
PANEL_ON/OFF DC/DC VCC0.9V_FRC

CN802
16V 12V Symbol Pin No.
DC/DC 12V-Panel 5
12V-Panel 4
12V-Panel 3
GND 2
16V GND 1

DC/DC

DC/DC VCC1.8V_FRC
+5V_Standby
CN803
DC/DC VCC3.3V_FRC Symbol Pin No.
PS_ON NC 12
NC 11
FB VCC5V_FRC NC 10
GND 9
+5V_Normal 8
SDO_SBL 7
SCL_SBL 6
DC/DC +1.15V_VDDC SDI_SBL 5
GND 4
CS_SBL 3
DC/DC 3.3V_Standby HSYNC_SBL 2
VSYNC_SBL 1

5V_DDRV

DC/DC +1.8V_DDR2

LED Driver pwb LED Back Light

43" : 16.25V
50" : 19.7V CN8601 CN8606 CN8605
55" : 22.1V Symbol Pin No. Pin No. Symbol Symbol Pin No. Pin No. Symbol
19.5V circuit +19.5V 14 1 Vin VLED 1 1 Anode
+19.5V 13 2 Vin VLED 2 2 Anode
PN_ON=L : 0V +19.5V 12 3 Vin VLED 3 3 Anode
6 strings
PS_ON=H : 19.5V +19.5V 11 4 Vin VLED 4 4 Anode
+19.5V 10 5 Vin VLED 5 5 Anode
GND 9 6 GND VLED 6 6 Anode
GND 8 7 GND VLED 7 7 NC
6 series
GND 7 8 GND VLED 8 8 NC
GND 6 9 GND LED FB16 9 9 NC
GND 5 10 GND Drive IC FB15 10 10 NC
DIM 4 11 ON/OFF PF7713 FB14 11 11 NC
16V 12V BL ON/OFF 3 12 DIM U8804 FB13 12 12 NC
Regulator DB Vcc 2 13 VCC LED FB12 13 13 Cathode 12
COMP 1 14 COMP Drive IC FB11 14 14 Cathode 11
PF7713 FB10 15 15 Cathode 10
AC Inlet U8803 FB09 16 16 Cathode 09
LED FB08 17 17 Cathode 08
Drive IC FB07 18 18 Cathode 07
12 strings
PF7713 FB06 19 19 Cathode 06
U8802 6 series
FB05 20 20 Cathode 05
LED FB04 21 21 Cathode 04
Drive IC FB03 22 22 Cathode 03
PF7713 FB02 23 23 Cathode 02
U8801 FB01 24 24 Cathode 01

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8 - 11

PN-UH431

Power Supply pwb I/F pwb

CN9101 CN701 CN801

Symbol Pin No. Pin No. Symbol BL_ON Pin No.
44-51 pin
DIM 16 16 BL_ON 51
BL_ON/OFF 15 15 BL_DIM BL_DIM ：
PS_ON PS_ON/OFF 14 14 NC 1
COMP 13 13 PS_ON PS_ON
GND 12 12 GND
GND 11 11 GND
GND 10 10 GND
PN_ON=L : 13V GND 9 9 GND
PS_ON=H : 16V 16V2 8 8 +16V_AUD 16V_AUD
T-CON pwb
16V2 7 7 +16V_AUD
16V 16V 6 6 +16V 16V
16V 5 5 +16V CN408
16V 4 4 +16V Pin No. Pin No.
44-51 pin
16V 3 3 +16V 51 1
NC 2 2 NC ： V-by-One ：
NC 1 1 NC 1 51
PANEL_ON/OFF DC/DC VCC0.9V_FRC

CN802
16V 12V Symbol Pin No.
DC/DC 12V-Panel 5
12V-Panel 4
12V-Panel 3
GND 2
16V GND 1

DC/DC

DC/DC VCC1.8V_FRC
+5V_Standby
CN803
DC/DC VCC3.3V_FRC Symbol Pin No.
PS_ON NC 12
NC 11
FB VCC5V_FRC NC 10
GND 9
+5V_Normal 8
SDO_SBL 7
SCL_SBL 6
DC/DC +1.15V_VDDC SDI_SBL 5
GND 4
CS_SBL 3
DC/DC 3.3V_Standby HSYNC_SBL 2
VSYNC_SBL 1

5V_DDRV

DC/DC +1.8V_DDR2

LED Driver pwb LED Back Light

43" : 16.25V
50" : 19.7V CN8601 CN8606 CN8605
55" : 22.1V Symbol Pin No. Pin No. Symbol Symbol Pin No. Pin No. Symbol
19.5V circuit +19.5V 14 1 Vin VLED 1 1 Anode
+19.5V 13 2 Vin VLED 2 2 Anode
PN_ON=L : 0V +19.5V 12 3 Vin VLED 3 3 Anode 5 strings
PS_ON=H : 19.5V +19.5V 11 4 Vin VLED 4 4 Anode
+19.5V 10 5 Vin VLED 5 5 Anode
GND 9 6 GND VLED 6 6 NC
GND 8 7 GND VLED 7 7 NC
5 series
GND 7 8 GND VLED 8 8 NC
GND 6 9 GND LED FB16 9 9 NC
GND 5 10 GND Drive IC FB15 10 10 NC
DIM 4 11 ON/OFF PF7713 FB14 11 11 NC
16V 12V BL ON/OFF 3 12 DIM U8804 FB13 12 12 NC
Regulator DB Vcc 2 13 VCC LED FB12 13 13 NC
COMP 1 14 COMP Drive IC FB11 14 14 NC
PF7713 FB10 15 15 Cathode 10
AC Inlet U8803 FB09 16 16 Cathode 09
LED FB08 17 17 Cathode 08
Drive IC FB07 18 18 Cathode 07
PF7713 FB06 19 19 Cathode 06
U8802 5 series
FB05 20 20 Cathode 05 10 strings
LED FB04 21 21 Cathode 04
Drive IC FB03 22 22 Cathode 03
PF7713 FB02 23 23 Cathode 02
U8801 FB01 24 24 Cathode 01

PN-UH861/UH551/UH501/UH431 HARDWARE DESCRIPTIONS 8 - 12

Service Manual Revision History
Model： PN-UH861, PN-UH551, PN-UH501, PN-UH431

No. Revised version Change time Chapter Page Revision history

1 New Release 2018/11/21 - - Issued the first edition of Service manual

2 2nd Release 2018/12/19 6 - Add the disassembly and assembly procedure for PN-UH551/UH501/UH431.
3 3rd Release 2019/2/27 4 4-1 Add [CAUTION] when Service menu is closed.

<About the revision mark on the Service Manual>

The meaning of the revision mark described in the Service manual is as follows.

The number of the revision recprd = the number of the revision mark.

No. Revised version Change time Chapter Page Revision history

1 New Release 2014/1/1 - - First edision issued Service Manual
2 XXXX Release XXXX/X/X X X-X XXXXXXXXXXXXXXXXXXXXXXX
3 XXXX Release XXXX/X/X X X-X XXXXXXXXXXXXXXXXXXXXXXX

Revision mark：Revision year and date

Revision mark

Revised part
 C 2019 BY SHARP CORPORATION
COPYRIGHT○
All rights reserved.
Published in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.

Trademark acknowledgements
• Microsoft, Windows, PowerPoint, Excel and Internet Explorer are either registered trademarks or
trademarks of Microsoft Corporation in the United States and/or other countries.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks
or registered trademarks of HDMI Licensing LLC in the United States and other countries.
• DisplayPort is a registered trademark of Video Electronics Standards Association.
• Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
• MHL, the MHL logo, and Mobile High-Definition Link are trademarks or registered trademarks of MHL,
LLC in the United States and other countries.
• Intel, Celeron, and Intel Core 2 Duo are trademarks or registered trademarks of Intel Corporation or its
subsidiaries in the U.S.A. and other countries.
• AMD, AMD Sempron, AMD Athlon, and combinations thereof are trademarks of Advanced Micro
Devices, Inc.
• Apple, Mac and Mac OS are registered trademarks of Apple Inc.
• All other brand, product names and other proper nouns are trademarks or registered trademarks of
their respective holders.

SHARP CORPORATION
Business Solutions BU

First edition : November 2018

Revised edition : February 2019