DV490FHM NN0 Boe
DV490FHM NN0 Boe
TITLE :DV490FHM-NN0
REVISION HISTORY
REV. PAGE DESCRIPTION OF CHANGES DATE PREPARED
Contents
VDD
+12.0V
G1
LVDS
CN1
2 Port
(51pin)
Timing Controller
LVDS
Select
[LVDS Rx & Mini-LVDS
Tx integrated]
TFT - LCD Panel
(1920 × RGB × 1080 pixels)
G1080
S1 S1920
1.2 Features
l GOA Dual Side Drive
l LVDS interface with 2 pixel / clock
l High-speed response
l Low color shift image quality
l 8-bit color depth, display 16.7M colors
l Narrow bezel and wide viewing angle,gate driver use GOA mode
l ADS technology is applied for high display quality
l RoHS compliant
1.3 Application
l Home Alone Multimedia TFT-LCD TV
l Display Terminals for Control System
l Full High Definition TV(FHD TV)
l AV application Products
Note 1 : Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 ℃ max. and no condensation of water.
Note 1 : The supply voltage is measured and specified at the interface connector of LCM.
The current draw and power consumption specified is for VDD=12.0V,
a) Typ : Mosaic 7X5 (L0/L255) b) Max : Horizontal 1 Line (L0/L255) ) c) Flicker Pattern
R G B R G B R G B
R G B R G B R G B
R G B R G B R G B
R G B R G B R G B
R G B R G B R G B
R G B R G B R G B
R G B R G B R G B
R G B R G B R G B
Note 2 : The duration of rush current is about 2ms and rising time of Power Input is 1ms(min)
Backlight on - - 5.0 V
EN Control
Level
Backlight off 0 V
PWM High
PWM - - 5.0 V
Level
Control
Level PWM Low
0 - - V
Level
The test of Optical specifications shall be measured in a dark room (ambient luminance £ 1
lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer
system and TOPCON BM-5) and test unit shall be located at an approximate distance
50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0
(=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction
(“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and
θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θand/or Ø, the center
of the measuring spot on the Display surface shall stay fixed. The backlight should be
operating for 30 minutes prior to measurement. VDD shall be 3.3+/- 0.3V at 25°C.
Optimum viewing angle direction is 6 ’clock.
4.2 Optical Specifications
<Table 5. Optical Specifications>
Notes :
1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing
angles are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12
o’clock direction with respect to the optical axis which is normal to the LCD surface (see
FIGURE 1).
2
4 Measurement Setup
The LCD module should be stabilized at given temperature for 30 minutes to avoid
abrupt temperature change during measuring. In order to stabilize the luminance, the
measurement should be executed after lighting Backlight for 30 minutes in a windless
room.
LCD Module
LCD Panel
78 9
4 56
123
0 ►
.
4 NC No Connection 24 NC No Connection
5 NC No Connection 25 NC No Connection
12 LO[0]- LVDS Odd Signal 0(-) 32 LE[2]- LVDS Even Signal 2(-)
13 LO[0]+ LVDS Odd Signal 0(+) 33 LE[2]+ LVDS Even Signal 2(+)
15 LO[1]+ LVDS Odd Signal 1(+) 35 LECLK- LVDS Even Clock Signal(-)
16 LO[2]- LVDS Odd Signal 2(-) 36 LECLK+ LVDS Even Clock Signal(+)
19 LOCLK- LVDS Odd Clock Signal(-) 39 LE[3]+ LVDS Even Signal 3(+)
46 GND Ground
Notes : 1. NC(Not Connected) : These pins are only used for BOE internal operations.
2. BIST : Panel will be in “BIST” mode when input DE or input CLOCK quits toggli
ng.
A - 100 - mV
B - 100 - mV
C - 0 - mV
D - -100 - mV
E - -100 - mV
F - 0 - mV
Output otal
Ggp 1
group
The Total
R 720 900 MA
Output Current
Input connector
0V=Brightness Max
14 ADJ Dimming control
5V=Brightness Min
Notes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on
normal operation.
< Table 8. LVDS Input SSCG>
tCLK
DCLK 0.5 VDD
Valid data
First data Invalid data Pixel data Pixel data Invalid data
Valid data
Second data Invalid data Pixel data Pixel data Invalid data
DE(Data Enable)
tHP
HSync
tHV
DE(Data Enable)
tVP
VSync
tVV
DE(Data Enable)
7.3 Input Signals, Basic Display Colors and Gray Scale of Colors
< Table 8. Input Signal and Display Color Table >
Notes: 1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is
satisfied.
序列号标注部分需打印, 说明如下:
1. FG-CODE(前12位)
2. MDL ID 及其条形码
Total Size: 36.5×7mm
序列号标注部分需打印, 说明如下:
•FG-CODE(前12位) 2. 产品数量
3. Box ID 4. 包装日期
•FG-Code后四位
Total Size:100×50mm