MoviSight

Network Camera Web Server

(IE page)
User Manual
 User Manual of Network Camera Web Server (IE page)

Table of Contents

1. NETWORK CONNECTION..................................................................................................................... 3
1.1 Wiring over the LAN........................................................................................................................... 3
1.1.1. Set the block camera via a LAN(Local Area Network)......................................................... 3
1.1.2. Set the network camera over the LAN via a switch or a router........................................... 3
1.2. ACTIVATING THE CAMERA...........................................................................................................3
2. ACCESSING TO THE NETWORK PTZ CAMERA..............................................................................4
2.1 Accessing by Web Browser...............................................................................................................4
2.1.1 Password Modification................................................................................................................ 5
2.2. Basic Operation..................................................................................................................................6
2.2.1 Live View Parameter................................................................................................................... 6
2.2.2 PTZ Control Panel....................................................................................................................... 7
2.2.3 OSD Setting..................................................................................................................................9
2.2.4. Alarm Info.................................................................................................................................... 9
2.3 Playback.............................................................................................................................................10
2.3.1 Search by Date.......................................................................................................................... 11
2.3.2. Search Video............................................................................................................................ 11
2.3.3. Recording Status......................................................................................................................11
2.4 Configuration..................................................................................................................................... 12
2.4.1. System information.................................................................................................................. 12
2.4.2. System setup............................................................................................................................ 13
2.4.3. Network setting.........................................................................................................................26
2.4.4 Storage settings.......................................................................................................................344
2.4.5. Alarm Setting............................................................................................................................ 36
2.4.6. Equipment Log..........................................................................................................................39
2.4.7 Local Setting.............................................................................................................................. 41
2.5. Intelligence........................................................................................................................................42
2.5.1 Perimeter.................................................................................................................................... 42
2.5.2 Line-crossing Detection............................................................................................................44

2
 1. NETWORK CONNECTION

1.1 Wiring over the LAN

1.1.1. Set the camera via a LAN(Local Area Network)

1.1.2. Set the network camera over the LAN via a switch or a router

1.2. ACTIVATING THE CAMERA

Auto Search Tool is used for detecting the online device, activating the device, and resetting the
password. Get the Auto Search Tool from the supplied disk or the official website, and install the
Auto Search Tool according to the prompts. Follow the steps to activate the camera
Steps:
1. Run the software to search the online devices.
2. Check the device status from the device list, and select an inactive device
The software supports activating the camera in batch. Refer to the user manual of
Auto Search Tool for details.

Fig
ure 1.2.1 Auto Search Tool

3
 2. ACCESSING TO THE NETWORK CAMERA

2.1 Accessing by Web Browser

Steps:
1. Power on the camera, and connect the camera to the network.
2. Open the web browser.
3. In the address field, input the IP address of the network camera, e.g., 192.168.1.19
and press the Enter key to enter the login interface.
4. The default IP address of the camera is 192.168.1.19.
5. Select English as the interface language on the bottom-right of login interface
6. Create a password and input the password in the password field, and confirm the
password
7. The admin user should configure the device accounts and user/operator permissions
properly. Delete the unnecessary accounts and user/operator permissions.
8. Install the plug-in before viewing the live video and operating the camera. Follow the
installation prompts to install the plug-in.

Caution：Please follow the installation prompts to install the plug-in.

Caution： You may have to close the web browser to install the plug-in. Reopen
the web browser and log in again after installing the plug-in.

Default user name: admin

Default password: abcd1234

4
 2.1.1 Password Modification

For your privacy and to better protect your system against security risks, we strongly
recommend the use of strong passwords for all functions and network devices. The
password should be something of your own choosing (using a minimum of 8
characters, including upper case letters, lower case letters, numbers and special
characters) in order to increase the security of your product.  Proper configuration of
all passwords and other security settings is the responsibility of the installer and/or

end-user

5
 2.2. Basic Operation
In this and the following chapters, operation of the block camera by the web browser will be taken
as an example.

Figure 2.2.1 Live Page

2.2.1 Live View Parameter

LOGO Description
Login
PTZ Control

Image Setting

Alarm Info

Latency

Regional Zoom

Quick PTZ

Zone Focus

Main Stream Live View

Second Stream Live View

Third Stream Live View

1:1 Display

6
 Local Record

Local Snapshot

IPC Snapshot

Audio Detect

Intercom

Stop Live View

Full Screen

2.2.2 PTZ Control Panel

PTZ Control: Panning, tilting, focusing and zooming actions of the network. The lighter, wiper,
one-touch focus and lens initialization control.
Preset/patrol/pattern: Set and call the preset/patrol/pattern for the camera
PTZ Control Panel

Figure 2.2.2

: Start/stop digital zoom.

/ : Focus near/far
/ : Iris Close/Open
Step: Control by Clicking on -/+ (Adjust speed of pan/tilt movements)
Setting a Preset: In the PTZ control panel, Input a preset number from 1-255, Click
to add a Preset, then click to call the PTZ to the Preset, Delete the Preset by clicking
on .

PTZ menu : Patrol/Line Scan/Pattern/Preset/Auto Pan/Aux

In the PTZ control panel, input a defined preset/pattern.
“Open”“Close”：Turn ON/OFF function.

1）PTZ Setting

7
Figure 2.2.3 PTZ Setting Menu

2) Line Scan：

Figure 2.2.4 Line Scan

Setting the Left and Right boundary
3) Pattern：

Figure 2.2.5 Pattern

3) Preset：

8
 Figure 2.2.6 Preset

You can configure up to 255 presets

4)Patrol：

Figure 2.2.7 Patrol

2.2.3 OSD Setting

Figure 2.2.8 Image Setting

2.2.4. Alarm Info

Figure 2.2.9 Alarm Info

2.3 Playback

Purpose:
This section explains how to view the video files stored in the network disks or memory
cards.

9
 Figure 2.3 Playback

Description of the buttons

logo Description
The window size is 1:1

Local Recording

Local Snapshot

IPC Snapshot

Audio Recording

Play

Speed Down

Speed Up

Full Screen

Drag the progress bar with the mouse to locate the exact playback point.

The different colors of the video on the progress bar stand for the different video
types

2.3.1 Search by Date

10
 Figure 2.3.1 Query Date

2.3.2. Search Video

Figure 2.3.2 Query Terms

You can choose the file paths locally for downloaded playback video files and pictures in Local
Configuration interface.

2.3.3. Recording Status

Figure 2.3.3 Status Information

You can also input the time and click to locate the playback point in the Set playback time field. You can
also click to zoom out/in the progress bar

11
 2.4 Configuration
Click Configuration to enter the Configuration
Interface

Figure 2.4 Setting

The configuration interface functions are as follows:

2.4.1. System information

Image2.4.1 system information

1） “Version information”

12
 Image2.4.2 Version information
You can view the device's "serial number, MAC, product type, software version,
hardware version, WEB version, control version, compilation date, activation status" and
other information.

2） “Operation and maintenance information”：

Image2.4.3 Version information

You can view CPU utilization and memory utilization.
3） “Hard disk information”：

Image2.4.4 Hard disk information

You can view "hard disk serial number", "physical serial number", "disk group", "hard
disk status", "properties", "residual capacity", "total capacity", and refresh status
information.

2.4.2. System setup

13
 Image 2.4.5 System setup

2.4.2.1 General setting

Image2.4.2.1 General setting

"Date Settings" can set "year", "month", "day", "time", "minute" and "second" separately.
Synchronized PC: Time synchronization with PC terminal.
"Automatic Synchronization": Automatically synchronize with PC after selecting.
"Save time": After setting up, click Save, it will pop up and save successfully.
Refresh: Click to refresh the display.
"Summer saving time": Check and set menu, set parameters according to demand, can
set "week" or "date".
"Date format": According to the needs of the sort of year, month and day set, can choose
"year, month, day and year", "day, month and year". "Delimiter": Set according to the
requirement. Optional". "," -","/".
"Time zone": Set up 12 hours and 24 hours display according to requirement.
"Time zone": Set up according to requirements.

14
"Storage device full time": according to the needs of settings, optional "coverage" or
"stop".
"Language": Set up according to the requirement, choose "Simplified Chinese" or
"English".
"Video format": Depending on the requirements, choose "PAL" or "NTSC"
"Local Number": Local Number Display.
"Save": After setting up, click Save, it will pop up and save successfully.
Refresh: Click to refresh the display.

2.4.2.2 Encoding setting

Figure 2.4.2.2 Encoding Setting

“Channel”: Select the appropriate channel for configuration.

"Coding mode": Select H265, H264 and MJPEG according to requirements. (The main
stream is H265 and H264 only)
"Coding Level": Set up High Profile, Main Profile and Baseline Profile according to
requirements.
"Encoding Enables": Video default check, according to the needs of audio enable check.
"Resolution": Choose according to demand. The main stream can choose "2592*1520
(unsupported), 2304*1296 (unsupported), 1920*1080" and "1280*720"; the auxiliary
stream can choose "720*576" and "352*288"; the third stream can choose "720*576"
and "352*288".
"Frame Rate": Set PAL (1-25 FPS) and NTSC (1-30 FPS) according to requirements.
"Bit Rate Value": Set according to requirements (with 10 fixed values and custom
settings).
"Bit Rate control": Settings according to requirements (with limited and variable bit
stream settings).
15
"I Frame Interval": Set up according to requirement (1-100).
"Bit Rate Smoothing": Settings (0-100) according to requirements (if there is breathing
effect in the image).
"Input volume": Adjust audio input sound (0-100) according to demand.
"Output volume": adjust the audio output sound (0-100) according to the demand.
“H264+/H265+”： Widening the I frame interval and increasing the virtual I frame to
ensure the smoothness of the picture in the same bit rate.
"SVC": SVC configuration can choose "1", "2" and "4" times; Scalable Video Coding
(adaptive video coding or scalable video coding) intelligent adjustment mode for
increasing frame hopping logic. (Not supported)
"Save": After setting up, click Save, it will pop up and save successfully.
Refresh: Click to refresh the display.
2.4.2.3. Audio setting

Image2.4.2.3 Audio settings

"Coding mode": Set the audio coding mode, choose "G711A", "AAC","G711U", "G726"
"Sampling Rate": Sampling Rate of Audio (each encoding mode corresponds to a
sampling rate).
"Sampling depth": The sampling depth of audio (each coding mode corresponds to a
sampling depth).
2.4.2.4. Image setting

2.4.2.4 Image setting

1）OSD setting
16
 1） OSD setting
“Preview Interface”: After saving the parameter settings, you can see the effect.
“Display Name”: Enabling Check of Display Name.
“Channel Name”: Set up according to requirements.
"Display Date": Enabling Check of Display Date.
"Show Week": Enabling Check of Show Date.
"OSD Anti-color": Turn on and off OSD Anti-color function.
“Font Size”: Set fonts 1, 2 and 3 as required.
"Text Edge Description": Open Red Edge Description for Web Preview Text
(not supported)
"Display multiple lines": Enable selected and sets 1-5 lines separately according to
requirements.
Alignment: alignment of multiple lines according to requirements.
"Save": After setting up, click Save, it will pop up and save successfully.

2) Area Mask

2） Privacy Mask

17
“Preview Interface”: After saving the parameter settings, you can see the effect.
“Drag box selection to add area”： Select the area in the preview interface, and
corresponding and black will appear.
Clear All: All settings are cleared.
"Delete the selected area": Delete the selected area pertinently.
"Save": After setting up, click Save, it will pop up and save successfully.
3）Image parameter

3）Image setting

“Preview Interface”: After setting parameters, you can see the effect.
【General Configuration】：

3.1) General Configuration

"Distortion Correction": Closing, Manual Options. "Strength Value": Use with manual
option of distortion correction (0-100)
“Electronic Anti Shake, ": Closing and Automation Options, "Strength Value": Use with
Electronic Anti-shake Automation Options (0-100).
"Image Style": Standard outdoor choice.
"Mirror": Settings can be checked to switch the symmetrical display direction of the video
screen.
“Flip”：” Check the settings. Video coding will rotate 90 degrees counterclockwise.。
"Corridor mode": Check the settings to switch the display proportion of the video, such
as the 16:9 corridor mode after switching to 9:16.
【Day/Night Shift】:

18
3.2) Day/Night Shift
"Color mode": automatic, daytime, night etc.
"Switching Basis": Photoresistor (not supported), image algorithm, time period selection,
external trigger, alarm input trigger, serial trigger.
"Switching threshold": daytime switching threshold, high numerical setting, the camera
needs a higher brightness to switch from night mode to daytime mode, low numerical
setting, the camera only needs a slightly lower brightness to switch from night mode to
daytime mode; night switching threshold, the same reason as daytime switching
threshold.
"Time Delay": Waiting time delayed response after day and night switching, can be set
according to demand.
"Inversion Selection": IRCUT Inversion: Forced switching of filters, triggering inversion:
Reversion of the current state, you can check settings according to needs.
【Focus Settings】：

Focus Mode: Manual, automatic and semi-automatic mode optional.

"Near limit" can be selected according to the actual application environment, and "3", "6",
"12", "24", "36" and "48" can be selected.
"Maximum Zoom Ratio: You can choose the maximum zoom ratio according to your
needs, and display the odds in the preview screen after opening.
"Initialize Lens": Click the trigger button to focus once under the default parameters.
"Shot Initialization": Click on trigger and the device performs a shot initialization
operation.
【Configuration selection】:
The configuration of image selection can be automatic, daytime and night.

【Image adjustment】：

19
 3.4) Image adjustment
"Image adjustment": brightness, contrast, saturation, sharpness and Hue (0-100) can
be adjusted according to demand.
【Exposure】:

、 3.5) Exposure adjustment

"Exposure mode": automatic, anti-drag, manual, shutter priority, low light priority, high
light priority and other options.
"Gain": Can be adjusted according to demand (0-100).
"Shutter Limit": Can be adjusted according to demand (10-640000 microseconds).
"Shutter Extension": Shutdown, automatic, weak, medium and strong.
"Anti-flicker Anf Mode": There are many choices, such as 50HZ automatic, 60HZ
automatic, 50HZ compulsory, 60HZ compulsory and so on.
【WDR】:

3.6) WDR

“Dynamic Range”：Close or WDR.

"Light Comp": BLC, HLC, etc.

【Sharpness】：

20
 3.7) Definition

“3D DNR”：Close, Automatic, Manual are options.。

“Anti-Fog”：Close and Manual are options。
“Gamma”：Close and region selection are options

【W/B】：

3.8) W/B

Select "automatic", "manual", "sunny", "cloudy", "dusk", "incandescent lamp", "sodium

lamp", "fluorescent lamp", "once tracking", "automatic tracking", "special light source",
"lock selection".

【Restore default】：
Click "Default Recovery" to restore default values for all image parameters.
2）ROI Setting

3.9) ROI Setting

Preview Interface: After saving the parameter settings, you can see the effect.

21
 "Drag the box to select the add area": The mouse clicks on the preview interface, and
the corresponding box appears.
Clear All: All boxes set are cleared.
"Delete the selected area": Delete the selected area pertinently.
"Qp value": can be adjusted according to demand (0-100).
"Save": After setting up, click Save, it will pop up and save successfully.
3) Image superimposition

Figure 3.10Image superimposition

Select the picture that meets the requirement, click upload, turn on the enabler, save it
and upload it successfully, and you can see the overlapped picture.
2.4.2.5 User management

Figure 2.4.2.5 User management

User management displays a list of existing users.

"Add" can set user name, password, comment, validation password, user group
(admin, user optional) and functional permissions.
Delete: Delete the created user.
"Modify": User names, user groups and permissions can be modified for the created
users.
"Modify password": Enter the original password, the new password and the verification
password, and click Confirm to complete the modification.
2.4.2.6 User Information

Figure 2.4.2.6 User online

You can view the IP of the login device, user name, login time.
2.4.2.7. PTZ Setting

22
 Figure 2.4.2.7 PTZ setting

"Protocol": Click on the drop-down menu to pop up a variety of protocols to choose

according to needs, and will continue to update.
“Address”: Set as needed (0-255).
"Baud Rate": Click on the drop-down menu to pop up a variety of parameters to
choose according to needs, baud rate "2400" - "115200" multiple options.
"Data bits": Click on the drop-down menu to pop up a variety of parameters to choose
according to needs, and choose "5", "6", "7", "8".
“Stop Bit”: Click on the drop-down menu "1" and "2" to choose.
"Parity": Click on the drop-down menu "None", "Odd Check" and "Even Check" to
select according to needs.
"Save": After setting up, click Save, it will pop up and save successfully.
Refresh: Click to refresh the display.
2.4.2.8 Image capture setting

Figure 2.4.2.8 Image capture setting

Channel Enables: Enables are selected and set according to requirements.

“Time period”:

23
 Figure 2.4.2.8 Time period

Click the Settings button to pop up the Time Period Settings menu. Time settings can
be set for 6 time periods per day, synchronization settings can be targeted selection or
can be selected for a whole week. Settings need to be saved after completion. In
addition, there are single reset, all reset, confirm, cancel and other functions buttons,
which can be operated according to needs.
"Resolution": The resolution of captured images can be set according to the
requirements. There are options: "1920*1080" and "1080*720".
"Image quality": According to the requirements, the image quality of the snapshot can
be set, and "poor", "ordinary", "good", "good" and "best" can be selected.
“Interval (s)”：The time interval of capturing can be set according to the requirement
(1-120s)。

2.4.2.9 System maintenance

24
 Figure 2.4.2.9 system maintenance
"Auto Reboot ": You can click the drop-down selection (never/day/week) and time
point settings to complete the save.
"Reboot": Click , pop up menu, click confirm device to restart.
"Default": Click on the drop-down menu to choose simple recovery and full recovery
according to needs. After simple recovery, network settings and user management will
not be restored (no restart); all restore factory settings (prompt restart).
“Export”: Click, pop-up menu to select storage path and input file name, and then click
Save. Successful export will be prompted by text and progress bar.
"Configuration Import": Click Browse the pop-up menu, then select the configuration
file that needs to be imported and click Open. After confirming the file is correct, click
Configuration Import pop-up menu and click OK. Successful import will be prompted
by text and progress bar.
"Upgrade": Click to browse the pop-up menu, then select the software that needs to be
upgraded, Click to open, confirm that the software is correct, and then click the
upgrade pop-up menu. Click OK, there will be text and progress bar prompts for
successful upgrade, and the device will automatically restart.
Note: Power failure will cause equipment damage during upgrading. Please
do not cut off power. Please wait patiently for longer upgrade time.

25
 2.4.3. Network setting

Image 2.4.3 Network setting

2.4.3.1. Network setting

Figure 2.4.3.1 Network setting

"Network Settings": Network Type.

"DHCP": DHCP can be checked according to the need, and the device can
automatically obtain the network address and related network parameters.
26
"NIC Type": Network Card Type can be set, default self-adaptive, optional 10M half-
duplex, 10M full-duplex, 100M half-duplex, 100M full-duplex, 1000M full-duplex.
"MAC Address": Displays the MAC address of the camera. This address cannot be set
or changed.
"IP Version": IPV4 and IPV6 can be selected.
"IP ": Effective IP address settings can be made for devices as required.
"Mask" can set up subnet mask effectively for equipment according to need.
“Gateway”: Effective gateway settings can be made for devices as needed.
"DNS": DNS servers need to configure available server addresses, and need domain
name access to function properly.
"Device Name": Device name can be set according to need.
"HTTP Port": The default port is 80, which can be set to the device according to the
needs of network access.
"HTTPS Port": By default 8443, you can set the appropriate port for the device
according to the needs of network access.
"TCP Port": The default port is 9000, which can be set to the device according to the
needs of network access.
"Max connection": default 128 routes, according to the needs of network access
devices can be set accordingly.
"MTU Set" is self-adaptive by default and can be set 576-1500 manually.
"Save": After setting up, click Save, it will pop up and save successfully.
“Refresh”: Click to refresh the display.

2.4.3.2. RTSP

Figure 2.4.3.2 RTSP

Enables: Enables are selected and set according to requirements.

" Listening Port": The default port is 554, which can be set according to the needs of
network settings.
" Start Port": The default port is 20000, which can be set according to the needs of
network settings.
" Port Number" defaults to 1000 routes, which can be set according to the needs of
network settings.
27
"Save": After setting up, click Save, it will pop up and save successfully.
Refresh: Click to refresh the display.
2.4.3.3 NTP

Figure 2.4.3.3 NTP

Enables: Enables are selected and set according to requirements.
"Server IP": Set NTP server address, according to the need for appropriate settings.
"Port": The default port 123 can be set according to the needs of network settings.
"Renewal Period": Setting the time interval according to the requirements, the
equipment can be set every time interval.
"Time zone": According to the time zone where the equipment is located, it can be set
up according to the actual situation.
"Save": After setting up, click Save, it will pop up and save successfully
Refresh: Click to refresh the display.
2.4.3.4 DDNS

Figure 2.4.3.4 DDNS

"DDNS Type" can be selected as（ ）according to need.

Enables: Enables are selected and set according to requirements.
"Domain Name": The device domain name is the domain name that the user applies
for on the website of the software operator.
User Name: User Name applied for on the website of the software operator.
"Password": The password that the user applies for on the website of the software
operator.
"Save": After setting up, click Save, it will pop up and save successfully.

28
 Refresh: Click to refresh the display.
2.4.3.5 IP Authorization

Figure 2.4.3.5 IP right

Enables: Enables are selected and set according to requirements.

"Restriction Type" can be selected as（ ）according to the need.

Add IP": Enter the IP you need to add in the left input box first, and click Add IP
successfully and it will be displayed in the list below.
"Allowed IP List": If white list is selected in the above (restricted type), then all IP added
after that will be in this list.
"Prohibited IP List": If the blacklist is selected in the above (restricted type), then all the
IP added after that will be in this list.
Delete IP: Find the IP mouse in the list that needs to be deleted, click Select, and then
click Delete IP.
"Save": After setting up, click Save, it will pop up and save successfully.
Refresh: Click to refresh the display.

2.4.3.6 Email

29
 2.4.3.6 Email
Enable: click Enable and set according to requirement
SMTP Server: Set the address of SMTP Server and make the setting according to
requirement
Port: The default port is 25, which can be set according to requirement of network
settings
User Name: input the sender's mailbox username
Password: input the sender's mailbox password
Sender: input the sender's mailbox address
"Mail Title": input the subject of email
"Receiving Address": input the recipient's mailbox address (up to 5)
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display
2.4.3.7. FTP

2.4.3.7 FTP

30
 "File type": this can be selected ( )according to requirement
Enable: click Enable and set according to requirement
"Anonymity": when the anonymity Enabled, the camera can accesses to the FTP server
anonymously, and sets it up according to requirement
"Server": Set FTP server address according to requirement
Port: The default port 1024, and it can be set according to requirement of network settings
"User Name": Enter the user name with FTP upload authority
Password: Enter the password with FTP upload authority
"Remote directory": Set up the path to save the uploaded files, which can be set accordingly
according to requirement
"File Length": Limit the file size to be uploaded, and it can be set accordingly
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display
"Channel": Select what requirement to be uploaded, and make the settings accordingly
"Weekly". Equipment can be selected weekly according to requirement
"Timeperiod"this can beselected froma variety of choicesaccording torequirement ofthe
equipment (there are two time periods can be set, time can be set for different hours, images can
be chosen from Ordinary/Detection/Alarm)

2.4.3.8. UPNP

2.4.3.8 UPNP
Enable: click Enable and set according to requirement
"Web Port": The default port is 80, which can be set according to requirement of network
settings
"TCP Port": The default port is 34567, which can be set according to requirement of
network settings
"RTSP intercept port": Make port settings according to requirement of network settings
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display
2.4.3.9 PPPOE

2.4.3.9 PPPOE
Enable: click Enable and set according to requirement

31
User Name: input the username of PPPOE
Password: input the password of PPPOE
"IP": After saving, the camera will get a public IP address
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display

2.4.3.10 Active registration

2.4.3.10 Active registration

Enable: click Enable and set according to requirement
"Server IP" set the IP address of the platform server, which can be set according to
requirement
Server Port: It can be set according to requirement of network settings
"P2P Enable": click Enable and set according to requirement
User Name: input the user name of the device
Password: input the password for device
"Unified Equipment Identification": It should be calculated on the platform software and
then fill in
"Online status": Display active registration status
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display
2.4.3.11 Syslog

Figure 2.4.3.11 syslog

2.4.3.12 Onvif

32
 2.4.3.12 onvif
Enable: click Enable and set according to requirement
Port: The default port is 80, which can be set according to requirement
Version Information: Display onvif version
"discovery mode" select the equipment ( )according to requirement
"Authentication Enable": click Enable and set up according to requirement
"ODT Testing": click Enable and set according to requirement
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display

2.4.3.13 RTMP

2.4.3.13 RTMP

Enabling: click by default and set it according to requirement

"Port" setting port, default 1935, and it can be set accordingly according to requirement
"RTMP Push Enable": click to open RTMP Push function
"Stream Type": The default main stream can be selected according to requirement
Push Address is set according to requirement
"Save": click Save after setting, it will pop up and save successfully
33
Refresh: Click to refresh the display
2.4.3.14 RTMP PUSH
2.4.3.18 RTMP Push

2.4.3.15 Alarm Center

2.4.3.16 Alarm Center

Enable: click Enable and set according to requirement

"Server IP" sets the server IP address, which can be set according to requirement
"Port" defaults to 9033 port, which can be set according to requirement of network
settings
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display

2.4.4 Storage settings

2.4.4.2 Storage settings

2.4.4.1 Recording setting

34
 2.4.5.1 Recording setting
"Channel Number": Choose the channel to be recorded, and set it accordingly
according to requirement
"Video streaming": Choose the streams to be recorded, and set according to
requirement
Choose "mainstream" or "second stream"
"Length": refers to the length of each video file, which can be set according to
requirement (1-120 minutes)
"Preview time": refers to time in advance of each video file (several seconds), can be
set according to requirement (1-5 seconds)
"Time Settings": Time settings can be set for six periods per day. Video recording can
be selected as Normal, Detection and Alarm. Synchronization settings can be selected
for a whole week. Settings should to be saved after completion. In addition, there are
individual resets, which can be operated according to requirement
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display
All Resets: All settings are restored to default
2.4.4.2 Video control

2.4.5.2 Video control

"Video Control": there are Configuration, Always, Close Control options, and these can
be set up according to requirement
"Save": click Save after setting, it will pop up and save successfully
Refresh: Click to refresh the display
2.4.4.3.：Hard Disk Management

35
 2.4.4.3 Hard Disk Management

"Hard Disk Management": It can display the hard disk information, such as hard disk
serial number, physical serial number, disk group, hard disk status, attributes, surplus
capacity, and total capacity, etc.
Refresh: Refresh display
"Hard Disk Settings" select the serial number of the hard disk first according to
requirement, and then select "Set Read-Write", "Set Read-Only", "Set Redundancy",
"Clear Data", "Recovery Error", "Repartition", "Format". Click Confirm on the pop-up
menu, and set up according to requirement.

2.4.5. Alarm Setting

2.4.6 Alarm Setting

2.4.5.1. Video Mask

2.4.6.1 Video Mask

36
 "Detection type": The equipment can be selected ( ) according to
requirement.
Channel: Set up according to requirement.
Enable: click Enable and set according to requirement.
"Sensitivity": The equipment can be set up (0-100) as required.
"Alarm threshold": the equipment can be set up (0-100) according to requirement.
Area: Use the mouse to click and drag settings. The red areas are the monitoring
area, and the grey areas are the non-monitoring area.
"Select all areas": to Select all areas as the monitoring area.
"Clean up all areas": Clean all the monitoring areas.
"Time Period": Click the Settings button to pop up the Time Period Settings menu. Time
settings can be set for 6 periods per day. Synchronization settings can be selected by
target and for a whole week. Settings should to be saved after completion. In addition,
there is individual reset, all reset, confirm, cancel and other functions buttons, which can
be operated according to requirement.
"Send mail": click Enable according to requirement of settings. This requires the support
of network mail function settings
"Dejitter": this can be set (0-600 seconds) according to requirement of settings.
"Alarm Output": click Enable according to requirement of the settings.
"Output Delay": this can be set (10-300 seconds) according to requirement of settings.
"Video Channel": click Enable according to requirement of the settings.
"Video Delay": this can be set (10-300 seconds) according to requirement of settings.

"PTZ Linkage" click Enable to select ( ).To input preset point in Digital input box
according to requirement of setting.
"Capture": click Enable according to requirement of the settings.
"Save": Click Save after setting, it will pop up and save successfully.
Refresh: Click to refresh the display.
2.4.5.2 External Alarm

2.4.6.2 External Alarm

37
"Detection type": The equipment can be selected according to requirement.
"Channel": According to requirement, set 1 as alarm input #1, set 2 as alarm input #2
Enable: click Enable and set according to requirement.

"Trigger type" this can be selected ( ) according to requirement.

"Time Period": Click the Settings button to pop up the Time Period Settings menu. Time
settings can be set for 6 periods per day. Synchronization settings can be selected by
target and for a whole week. Settings should to be saved after completion. In addition,
there is individual reset, all reset, confirm, cancel and other functions buttons, which can
be operated according to requirement.
"Dejitter": this can be set (0-600 seconds) according to requirement of settings.
"Video Delay": this can be set (10-300 seconds) according to requirement of settings.
"Send mail": click Enable according to requirement of settings. This requires the support
of network mail function settings
"Alarm Output": click Enable according to requirement of the settings. Set 1 as alarm
input #1, set 2 as alarm input #2
"Output Delay": this can be set (10-300 seconds) according to requirement of settings.
"Video Channel": click Enable according to requirement of the settings.

"PTZ Linkage" click Enable to select ( ). To input preset point in Digital input box
according to requirement of setting.
"Capture": click Enable according to requirement of the settings.
"Save": Click Save after setting, it will pop up and save successfully.
Refresh: Click to refresh the display.

2.4.5.3. Alarm Output

2.4.6.3 Alarm Output

"Alarm mode": there are Configuration, Always, Close Control options, and can be set
according to requirement.
"Status": Alarm status prompts when the alarm output turns red.
"Save": Click save after setting, and it will pop up to save successfully.
Refresh: Click to refresh the display.
2.4.5.4. Abnormality Handling

38
 2.4.6.4 Abnormal Alarm

"Abnormal Type": Equipment can be selected ( ) according to

requirement.
Enable: click Enable and set according to requirement.
"Video Delay": this can be set (10-300 seconds) according to requirement of settings.
"Video Channel": click Enabled and make setting according to requirement
"Save": click Save after setting, it will pop up and save successfully.
Refresh: Click to refresh the display.

2.4.6. Equipment Log

2.4.7 Equipment Log

2.4.6.1.Log Search

39
 2.4.6.1 Log Search

"Type" This can be selected ( ) according to requirement of the device

"Start time": You can make separate setting on "year", "month", "day", "time", "minute"
and "second".
"End time" You can make separate setting on "year", "month", "day", "time", "minute"
and "second".
Search: After select the type, start and end times, click Search to display log information
during that period.
Clear: Click Clear pop-up menu to select OK, and clear all log information.
"Information Display Box": the log information will be displayed after search, and you can
view the serial number, log time, events, channels, extended content and other
information.

2.4.6.2 Log Configuration

2.4.6.2 Log Configuration

40
"Log Full": Stop/overwrite options can be selected according to requirement when the
log is full
"Save Log Type": Make Single Select or All Select to all the system information you
requirement to save.
"Save": click Save after setting, it will pop up and save successfully.
Refresh: Click to refresh the display.

2.4.6.3. Access to Log

2.4.7.3 Access to Log

"Search": Click Search to access to log information.
"Clear": Click on the Clear pop-up menu to select Confirm, and clear the log
information.
"Information Display Box": the log information will be displayed here.

2.4.7 Local Setting

2.4.8 Local Setting

"Capture Type": Local capture format can be set according to requirement, and "jpg"
or "bmp" can be selected according to requirement.
"Video Type": local video format can be set according to requirement, and ".dav" or
"mp4" can be selected according to requirement.
"Decoding Type": Optional: "Adaptive", "Hard Decode", "Soft Decode". This is aiming
at optimizing Preview stumble problem
"Video File Packing Time": Packing time can be set (1-60 minutes) as requirement.
"Video and capturing Path": Storage Path can be set as requirement (default
d:path_media).
"Save": click Save after setting, it will pop up and save successfully.
Refresh: Click to refresh the display.

41
 2.5. Intelligence
Click 【Intelligence】to enter the confirmation page

2.5 Intelligent Functions

2.5.1 Perimeter

2.5.1 Perimeter Detection

"Preview Interface": By default, there is an identification box, which can be dragged by
the mouse to zoom in and out (4 areas can be set). After saving the parameters, you can
see the effect.
Event Type: Default type is Perimeter.
Enable: click Enable and set according to requirement.
"Eliminate Shadows": turn on in special environments like in shadow and reflection
"Display Rule Line": click Enable and setting according to requirement.

42
"Max./Min. Object Alarm Height": After the max. click measurement, select the maximum
range of the left-click drop-down box in the small window, and the same operation can
set to the min. click.
"Alarm type": make settings according to requirement. There are two options: touch line
alarm/cross line alarm.
"Time Period": Click the Settings button to pop up the Time Period Settings menu. Time
settings can be set for 6 periods per day. Synchronization settings can be selected by
target and for a whole week. Settings should to be saved after completion. In addition,
there is single reset, all reset, confirm, cancel and other functions buttons, which can be
operated according to requirement.
"Send mail": click Enable according to requirement of settings. This requires the support
of network mail function settings
"Log": click Enable according to requirement of settings.
"Dejitter": this can be set (0-600 seconds) according to requirement of settings.
"Alarm Output": click Enable according to requirement of the settings.
"Output Delay": this can be set (10-300 seconds) according to requirement of settings.
"Video Channel": click Enable according to requirement of the settings.
"Video Delay": this can be set (10-300 seconds), according to requirement of settings.
"PTZ Linkage" click "PTZ Linkage" to enable the selection. Alarm linkages can be
selected (never/preset point/cruise group/patrol). To input preset point in Digital input
box according to requirement of setting.
"Capture": click Enable according to requirement of the settings.
"Save": Click Save after setting, it will pop up and save successfully.
Refresh: Click to refresh the display.

2.5.2 Line-crossing Detection

2.5.3 Line-crossing Detection

"Preview Interface": By default, there is an identification box, which can be dragged and
scribed by mouse (8 trigger lines can be set). After parameter setting saved, the effect
can be seen.
Event Type: Default type is Line-crossing.

43
Enable: click Enable and set according to requirement.
"Clear the line": Set up the preview interface according to requirement
"Clear Shadows": turn on in special environments like in shadow and reflection
"Display Rule Line": click Enable and setting according to requirement.
"Max./Min. Object Alarm Height": After the max. click measurement, select the maximum
range of the left-click drop-down box in the small window, and the same operation can
set to the min. click.
"Alarm type": make settings according to requirement. There are two options: touch line
alarm/cross line alarm.
"Time Period": Click the Settings button to pop up the Time Period Settings menu. Time
settings can be set for 6 periods per day. Synchronization settings can be selected by
target or can for a whole week. Settings should to be saved after completion. In addition,
there is single reset, all reset, confirm, cancel and other functions buttons, which can be
operated according to requirement.
"Send mail": click Enable according to requirement of settings. This requirement the
support of network mail function settings
"Log": click Enable according to requirement of settings.
"Dejitter": this can be set (0-600 seconds) according to requirement of settings.
"Alarm Output": click Enable according to requirement of the settings.
"Output Delay": this can be set (10-300 seconds) according to requirement of settings.
"Video Channel": click Enable according to requirement of the settings.
"Video Delay": this can be set (10-300 seconds), according to requirement of settings.
"PTZ Linkage" click "PTZ Linkage" to enable the selection. Alarm linkages can be
selected (never/preset point/cruise group/patrol). To input preset point in Digital input
box according to requirement of setting.
"Capture": click Enable according to requirement of the settings.
"Save": Click Save after setting, it will pop up and save successfully.
Refresh: Click to refresh the display.

44
MoviSight

45