Scribd
Upload
53 views

ATM

ATM is a cell-based switched wide area network protocol. It uses fixed-size cells (53 bytes) to efficiently multiplex different data streams. ATM networks establish virtual connections between endpoints using virtual path and circuit identifiers in cell headers. This allows cells from different connections to be efficiently routed through ATM switches to their destination. ATM supports both permanent and switched virtual circuits to provide flexible connectivity for various network traffic types.

Uploaded by

avantika bisht
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
53 views

ATM

ATM is a cell-based switched wide area network protocol. It uses fixed-size cells (53 bytes) to efficiently multiplex different data streams. ATM networks establish virtual connections between endpoints using virtual path and circuit identifiers in cell headers. This allows cells from different connections to be efficiently routed through ATM switches to their destination. ATM supports both permanent and switched virtual circuits to provide flexible connectivity for various network traffic types.

Uploaded by

avantika bisht
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 21

ATM

Asynchronous Transfer Mode (ATM) is a


switched wide area network based on
the cell relay protocol designed by the
ATM forum and adopted by the ITU-T.
The combination of ATM and SONET will
allow high-speed interconnection of all
the world’s networks. In fact, ATM can
be thought of as the “highway” of the
information superhighway.
1
Design Goals

Among the challenges faced by the designers of ATM,


six stand out.
1. The need for a transmission system to optimize
the use of high-data-rate.
2. The system must interface with existing systems.
3. The design must be implemented inexpensively.
4. The new system must be able to work with and
support the existing hierarchies
5. The new system must be connection-oriented.
6. Last but not least, one objective is to move as
many of the functions to hardware as possible.
2
Problems

Before we discuss the solutions to these design


requirements, it is useful to examine some of the
problems associated with existing systems.
• Frame Network
• Mixed Network Traffic

The solution
• Asynchronous TDM
• Cell Networks

3
• Frame Network
Before ATM, data communications at the data-link layer had been based on frame
switching and frame networks. Different protocols use frames of varying size and
intricacy. As networks become more complex, the information that must be
carried in the header becomes more extensive. The result is larger and larger
headers relative to the size of the data unit.

• Mixed Network Traffic


The variety of frame sizes makes traffic unpredictable. Another problem is that of
providing consistent data rate delivery when frame sizes are unpredictable and can
vary so dramatically
Multiplexing using different frame size
• Asynchronous TDM
ATM uses statistical (asynchronous) time-division multiplexing—that is why it is
called Asynchronous Transfer Mode—to multiplex cells coming from different
channels. It uses fixed-size slots (size of a cell). ATM multiplexers fill a slot with a
cell from any input channel that has a cell; the slot is empty if none of the channels has
a cell to send. When all the cells from all the channels are multiplexed, the output slots
are empty.
• Cell Networks
In a cell network, which uses the cell as the basic unit of data exchange, all data are
loaded into identical cells that can be transmitted with complete predictability and
uniformity. Because each cell is the same size and all are small, the problems
associated with multiplexing different-sized frames are avoided.
Multiplexing using cells

7
ATM multiplexing

8
Architecture

ATM is a cell-switched network. The user access


devices, called the endpoints, are connected through
a user-to-network interface (UNI) to the switches
inside the network. The switches are connected
through network-to-network interfaces (NNIs).

9
Architecture of an ATM network

10
Virtual Connections and Identifiers
• Virtual Circuits
• PVC : permanent virtual-circuit connection
• SVC : switched virtual-circuit connection
• Transmission Path (Physical connection)
• Virtual Path (VP)
• Virtual Circuits (VCs)
• Virtual Path Identifier (VPI)
• Virtual Circuits Identifier (VCI)

11
Virtual Connections and Identifiers
• Virtual Path Identifier (VPI)
• Virtual Circuits Identifier (VCI)
To route data from one endpoint to another, the virtual connections need to be
identified. For this purpose, the designers of ATM created a hierarchical identifier
with two levels: a virtual-path identifier (VPI) and a virtual-circuit identifier (VCI).
The VPI defines the specific VP, and the VCI defines a particular VC inside the VP.
The VPI is the same for all virtual connections that are bundled (logically) into one
VP.

12
TP, VPs, and VCs

13
Virtual connection identifiers in UNIs and NNIs

14
An ATM cell

15
Connection Establishment
• Connection oriented : ATM uses connection oriented mechanism for data
transmission
• SVC : In a switched virtual-circuit connection (SVC), each time an endpoint wants to
make a connection with another endpoint, a new virtual circuit must be established.
ATM cannot do the job by itself, but needs the network-layer addresses and the
services of another protocol (such as IP).
• PVC : A permanent virtual-circuit connection (PVC) is established between two
endpoints by the network provider. The VPIs and VCIs are defined for the permanent
connections, and the values are entered for the tables of each switch.
• Switching : ATM uses switches to route the cell from a source ndpoint to the
destination endpoint. A switch routes the cell using both the VPIs and the VCIs. The
switch checks its switching table, which stores six pieces of information per row:
arrival interface number, incoming VPI, incoming VCI, corresponding outgoing
interface number, the new VPI, and the new VCI.

16
Routing with a switch

17
ATM Layers
• AAL (Application Adaptation Layer)
• ATM Layer
• Physical Layer
ATM Layer
The ATM layer provides routing, traffic management, switching, and multiplexing services. It
processes outgoing traffic by accepting 48-byte segments from the AAL sublayers and
transforming them into 53-byte cells by the addition of a 5-byte header.
Physical Layer
Like Ethernet and wireless LANs, ATM cells can be carried by any physical-layer carrier.
AAL is divided into two sublayers :
SAR (segmentation and Reassembly) and CS (Convergence sublayer)
Versions of AAL are:- AAL1, AAL2, AAL3/4 and AAL5
AAL5 is also known as SEAL ( Simple and Efficient Adaptation Layer) and is designed for
Internet applications.
18
ATM layers

19
• AAL1 :- Constant Data bit Rate
• AAL2 : Initially for Variable data rate now used for low-bit-
rate traffic and short-frame traffic such as audio
(compressed or uncompressed), video, or fax
• AAL3/4 : Initially, AAL3 was intended to support
connection-oriented data services and AAL4 to support
connectionless services. As they evolved, however, it
became evident that the fundamental issues of the two
protocols were the same. They have therefore been
combined into a single format calledAAL3/4.
• AAL5 : assumes that all cells belonging to a single message
travel sequentially and that control functions are included
in the upper layers of the sending application.
20
AAL5

21

You might also like