1

PROJECT NO: FLOOR BEAMS

Refer: Calculations B1 Results
Design(Refer page )
Span on axis 3.2 Beam B1
B.S.8110 Max Positive M= 41 Kn.m b= 200 mm
Pa:1,1965 Max Neg M= 0 Kn.m D= 500 mm
Max Shear V= 51.6 Kn bott-st 2 Y- 16
Width of beam,b= 200 mm b.curt 0 Y- 0
Effective depth of beam,d= 462 500 top 2 Y- 14
Charact:strength of conc,fcu= 20 N/sq.mm t.o.c.s 0 Y- 0
Tensile st: of steel,fy= 415 N/sq.mm Stir:(1) 8 Y,@ 150
P3/9 K=M/(bd^2fcu) 0.04835 <0.156 Stir:(2) 8 Y,@ 150
Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2= 0.943033 d mm f.b 0 nos 0
leverarm limited to 0.95d
Then ,z= 0.943033 d mm
435.6811 mm
Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 262.4241 sq.mm
Provide 2 16 mmdia
0 0 mmdia
Area of tension reinf pro: 401.92 sq.mm Ast provided ok
For negative Moment,
Effective depth,d= 462 mm
K=M/(bd^2fcu) 0
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2= 1 d mm
Z= 0.95 d mm
438.9 mm
As= 0 sq.mm
Provide top 2 14 mmdia
0 0 mmdia
Area of top reinf: provided= 307.72 sq.mm Ast provided ok
Shear
%age of reinf,p=100As/b/d 0.434978
T3.9P3/11 Design shear stress,vc= 0.478857 n/mm^2 1
Actual shear stress,v=V/b/d 0.558442 n/sqmm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 2279.244 mm or .75*d 346.5
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia

Name the beam B1

 2
FLOOR BEAMS

DESIGN OF FLOOR BEAMS B1

BEAM ON AXIS
Span= 3.2 m
Assumed section 200 x 500
Loads coming
Uniformly distributed loads
Block + beams= 11.5 17.25 kn/m
From slab (1)= 10 15 kn/m
From slab (2)= 0 0 kn/m
Total load= 21.5 32.25 kn/m
Point Load (1)= 0 0 kn/m 0.5 m from left
Point Load (2)= 0 0 kn/m 5.1 m fromleft

32.25 kn/m

3.2 m
51.6 51.6
1.60 m

Reaction at left= 51.6 KN

Reaction at right= 51.6 KN
Point where shear force is zero,x= 1.60 m
Maximum span moment= 41 kn-m
PROJECT NO: FLOOR BEAMS 3
Refer: Calculations B4 Results
Design(Refer page )
Span on axis 4.2 Beam B4
B.S.8110 Max Positive M= 89 Kn.m b= 200 mm
Pa:1,1965 Max Neg M= 0 Kn.m D= 500 mm
Max Shear V= 85.05 Kn bott-st 2 Y- 16
Width of beam,b= 200 mm b.curt 2 Y- 14
Effective depth of beam,d= 462 500 top 2 Y- 14
Charact:strength of conc,fcu= 20 N/sq.mm t.o.c.s 2 Y- 0
Tensile st: of steel,fy= 415 N/sq.mm Stir:(1) 8 Y,@ 150
P3/9 K=M/(bd^2fcu) 0.104597 <0.156 Stir:(2) 8 Y,@ 150
Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2= 0.865761 d mm f.b 0 nos 0
leverarm limited to 0.95d
Then ,z= 0.865761 d mm
399.9815 mm
Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 618.3813 sq.mm
Provide 2 16 mmdia
2 14 mmdia
Area of tension reinf pro: 709.64 sq.mm Ast provided ok
For negative Moment,
Effective depth,d= 462 mm
K=M/(bd^2fcu) 0
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2= 1 d mm
Z= 0.95 d mm
438.9 mm
As= 0 sq.mm
Provide top 2 14 mmdia
2 0 mmdia
Area of top reinf: provided= 307.72 sq.mm Ast provided ok
Shear
%age of reinf,p=100As/b/d 0.768009
T3.9P3/11 Design shear stress,vc= 0.57877 n/mm^2 1
Actual shear stress,v=V/b/d 0.920455 n/sqmm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 530.8738 mm or .75*d 346.5
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia

Name the beam B4

FLOOR BEAMS 4
 DESIGN OF FLOOR BEAMS B4

BEAM ON AXIS
Span= 4.2 m
Assumed section 200 x 500
Loads coming
Uniformly distributed loads
Block + beams= 12 18 kn/m
From slab (1)= 15 22.5 kn/m
From slab (2)= 0 0 kn/m
Total load= 27 40.5 kn/m
Point Load (1)= 0 0 kn/m 1.7 m from left
Point Load (2)= 0 0 kn/m 0 m fromleft

40.5 kn/m

4.2 m
85.05 85.05
2.10 m

Reaction at left= 85.1 KN

Reaction at right= 85.1 KN
Point where shear force is zero,x= 2.10 m
Maximum span moment= 89 kn-m

PROJECT NO: FLOOR BEAMS 5

Refer: Calculations B7 Results
Design(Refer page )
Span on axis 5 Beam B7
B.S.8110 Max Positive M= 141 Kn.m b= 200 mm
Pa:1,1965 Max Neg M= 0 Kn.m D= 600 mm
Max Shear V= 112.5 Kn bott-st 3 Y- 16
Width of beam,b= 200 mm b.curt 2 Y- 14
Effective depth of beam,d= 562 600 top 2 Y- 14
Charact:strength of conc,fcu= 20 N/sq.mm t.o.c.s 0 Y- 14
Tensile st: of steel,fy= 415 N/sq.mm Stir:(1) 8 Y,@ 150
P3/9 K=M/(bd^2fcu) 0.111309 <0.156 Stir:(2) 8 Y,@ 150
Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2= 0.85542 d mm f.b 0 nos 0
leverarm limited to 0.95d
Then ,z= 0.85542 d mm
480.7461 mm
Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 810.1761 sq.mm
Provide 3 16 mmdia
2 14 mmdia
Area of tension reinf pro: 910.6 sq.mm Ast provided ok
For negative Moment,
Effective depth,d= 562 mm
K=M/(bd^2fcu) 0
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2= 1 d mm
Z= 0.95 d mm
533.9 mm
As= 0 sq.mm
Provide top 2 14 mmdia
0 14 mmdia
Area of top reinf: provided= 307.72 sq.mm Ast provided ok
Shear
%age of reinf,p=100As/b/d 0.810142
T3.9P3/11 Design shear stress,vc= 0.589166 n/mm^2 1
Actual shear stress,v=V/b/d 1.00089 n/sqmm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 440.5659 mm or .75*d 421.5
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia

Name the beam B7

FLOOR BEAMS 6
DESIGN OF FLOOR BEAMS B7

BEAM ON AXIS
Span= 5m
Assumed section 200 x 600
Loads coming
Uniformly distributed loads
Block + beams= 12 18 kn/m
From slab (1)= 18 27 kn/m
From slab (2)= 0 0 kn/m
Total load= 30 45 kn/m
Point Load (1)= 0 0 kn/m 1.2 m from left
Point Load (2)= 0 0 kn/m 0 m fromleft

45 kn/m

5m
112.5 112.5
2.50 m

Reaction at left= 112.5 KN

Reaction at right= 112.5 KN
Point where shear force is zero,x= 2.50 m
Maximum span moment= 141 kn-m
PROJECT NO: FLOOR BEAMS 5
Refer: Calculations B10 Results
Design(Refer page )
Span on axis 5.4 Beam B10
B.S.8110 Max Positive M= 164 Kn.m b= 200 mm
Pa:1,1965 Max Neg M= 0 Kn.m D= 700 mm
Max Shear V= 121.5 Kn bott-st 3 Y- 16
Width of beam,b= 200 mm b.curt 3 Y- 14
Effective depth of beam,d= 662 700 top 2 Y- 14
Charact:strength of conc,fcu= 20 N/sq.mm t.o.c.s 0 Y- 14
Tensile st: of steel,fy= 415 N/sq.mm Stir:(1) 8 Y,@ 150
P3/9 K=M/(bd^2fcu) 0.093569 <0.156 Stir:(2) 8 Y,@ 150
Lever arm ,
Z=d(0.5+(0.25-k/0.9)^1/2= 0.882144 d mm f.b 0 nos 0
leverarm limited to 0.95d
Then ,z= 0.882144 d mm
583.9792 mm
Area of tension reinforcement.
As=M*10^6/0.87/fy/Z 777.9385 sq.mm
Provide 3 16 mmdia
3 14 mmdia
Area of tension reinf pro: 1064.46 sq.mm Ast provided ok
For negative Moment,
Effective depth,d= 662 mm
K=M/(bd^2fcu) 0
p3/9 Z=d(0.5+(0.25-k/0.9)^1/2= 1 d mm
Z= 0.95 d mm
628.9 mm
As= 0 sq.mm
Provide top 2 14 mmdia
0 14 mmdia
Area of top reinf: provided= 307.72 sq.mm Ast provided ok
Shear
%age of reinf,p=100As/b/d 0.803973
T3.9P3/11 Design shear stress,vc= 0.587666 n/mm^2 1
Actual shear stress,v=V/b/d 0.917674 n/sqmm
T3.8P3/11 case (1) <0.5vc
case(2) 0.5vc<v<(vc+0.4)
case(3) (vc+0.4)<v<0.80(fcu)^(1/2)
Provide 8 mmdia stirrups
Area of cross section of stirr 50.24 sq.mm
spacing of two legged stirrups 549.6591 mm or .75*d 496.5
Provide st-s 8 mmdia @ 150 mm,c/c
Provide st-m 8 mmdia @ 150 mm,c/c
Face bars 0 nos 0 mmdia

Name the beam B10

FLOOR BEAMS 6
DESIGN OF FLOOR BEAMS B10

BEAM ON AXIS
Span= 5.4 m
Assumed section 200 x 700
Loads coming
Uniformly distributed loads
Block + beams= 13 19.5 kn/m
From slab (1)= 15 22.5 kn/m
From slab (2)= 2 3 kn/m
Total load= 30 45 kn/m
Point Load (1)= 0 0 kn/m 3.2 m from left
Point Load (2)= 0 0 kn/m 0 m fromleft

45 kn/m

5.4 m
121.5 121.5
2.70 m

Reaction at left= 121.5 KN

Reaction at right= 121.5 KN
Point where shear force is zero,x= 2.70 m
Maximum span moment= 164 kn-m