EurotestDL/XE

MI 3002/ MI 3102
Instruction manual
Version 1.1, HW 3; Code No. 20 750 468
Distributor:

Manufacturer:

METREL d.d.
Ljubljanska cesta 77
1354 Horjul
Slovenia

web site: http://www.metrel.si

e-mail: [email protected]

© 2004 -2008 METREL

Mark on your equipment certifies that this equipment meets the requirements of the EU
(European Union) concerning safety and interference causing equipment regulations.

No part of this publication may be reproduced or utilized in any form or by any means
without permission in writing from METREL.

2
MI 3002 & MI3102 Table of contents

1 Preface ......................................................................................................... 5
2 Safety and operational considerations ..................................................... 6
2.1 Warnings and notes .................................................................................... 6
2.2 Batteries ..................................................................................................... 9
2.3 Charging ..................................................................................................... 9
2.4 Precautions on charging of new battery cells or cells unused for a longer
period ....................................................................................................... 10
2.5 Standards applied ..................................................................................... 11
3 Instrument description ........................................................................... –12
3.1 Front panel ............................................................................................... 12
3.2 Connector panel ....................................................................................... 13
3.3 Back panel ................................................................................................ 14
3.4 Bottom view .............................................................................................. 15
3.5 Carrying the instrument ............................................................................ 16
4 Instrument operation ................................................................................ 17
4.1 Meaning of symbols and messages on the instrument display .......................... 17
4.1.1 The online voltage and output terminal monitor ................................... 17
4.1.2 Message field – battery status .............................................................. 18
4.1.3 Message field – measurement warnings/messages ............................. 18
4.1.4 Result field ........................................................................................... 19
4.1.5 Other messages ................................................................................... 19
4.1.6 Sound warnings.................................................................................... 20
4.1.7 Function and parameter line ................................................................. 20
4.2 Selecting measurement function/ subfunction .......................................... 20
4.3 Setting measurement parameters and limits ............................................ 21
4.4 Help menu ................................................................................................ 21
4.5 Setup menu .............................................................................................. 21
4.5.1 Supply system setup ............................................................................ 22
4.5.2 Impedance scaling factor adjustment ................................................... 22
4.5.3 Language selection .............................................................................. 23
4.5.4 Communication port selection .............................................................. 23
4.5.5 Plug / Tip commander support ............................................................. 23
4.5.6 Recalling original settings ..................................................................... 24
4.6 Display contrast adjustment...................................................................... 25
5 Measurements ........................................................................................... 26
5.1 Insulation resistance ................................................................................. 26
5.2 Continuity.................................................................................................. 28
5.3 Testing RCDs ........................................................................................... 31
5.3.1 Limit contact voltage............................................................................. 31
5.3.2 Nominal differential trip-out current ...................................................... 31
5.3.3 Multiplier of nominal residual current .................................................... 31
5.3.4 RCD type and test current starting polarity ........................................... 32
5.3.5 Testing selective (time-delayed) RCDs ................................................ 32
5.3.6 Contact voltage .................................................................................... 32
5.3.7 Trip-out time ......................................................................................... 35
5.3.8 Trip-out current ..................................................................................... 36
5.3.9 Autotest ................................................................................................ 37
5.4 Fault loop impedance and prospective fault current ................................. 41

3
MI 3002 & MI3102 Table of contents

5.4.1 Fault loop impedance ........................................................................... 41

5.4.2 The fault loop impedance test for RCD protected circuits .................... 43
5.5 Line impedance and prospective short-circuit current .............................. 45
5.6 Phase sequence testing ........................................................................... 47
5.7 Voltage and frequency .............................................................................. 48
5.8 Resistance to earth (MI 3102 only) ........................................................... 50
5.9 TRMS current (MI 3102 only) ................................................................... 52
5.10 Illumination (MI 3102 only)........................................................................ 54
5.11 Testing the PE terminal ............................................................................ 56
6 Working with results ................................................................................. 58
6.1 Saving results ........................................................................................... 59
6.2 Recalling results ....................................................................................... 60
6.3 Deleting results ......................................................................................... 62
7 RS232 / USB communication ................................................................... 65
7.1 EuroLinkPRO PC software ....................................................................... 65
8 Maintenance............................................................................................... 67
8.1 Replacing fuses ........................................................................................ 67
8.2 Cleaning ................................................................................................... 67
8.3 Periodic calibration ................................................................................... 67
8.4 Service...................................................................................................... 67
9 Technical specifications ........................................................................... 68
9.1 Insulation resistance ................................................................................. 68
9.2 Continuity resistance ................................................................................ 68
9.3 RCD testing .............................................................................................. 69
9.3.1 General data ........................................................................................ 69
9.3.2 Contact voltage .................................................................................... 69
9.3.3 Trip-out time ......................................................................................... 70
9.3.4 Trip-out current ..................................................................................... 70
9.4 Fault loop impedance and prospective fault current ................................. 71
9.5 Line impedance and prospective short-circuit current .............................. 71
9.6 Resistance to earth (MI 3102 only) ........................................................... 72
9.7 TRMS current (MI 3102 only) ................................................................... 72
9.8 Illumination (MI 3102 only)........................................................................ 73
9.8.1 Illumination (LUXmeter type B)............................................................. 73
9.8.2 Illumination (LUXmeter type C) ............................................................ 73
9.9 Phase rotation .......................................................................................... 73
9.10 Voltage and frequency .............................................................................. 73
9.11 Online voltage monitor .............................................................................. 74
9.12 General data ............................................................................................. 74
A Fuse base tables ....................................................................................... 76
B IT supply systems ..................................................................................... 77
C Reduced low voltage supply systems ..................................................... 85

4
MI 3002 & MI3102 Preface

1 Preface
Congratulations on your purchase of the Eurotest instrument and its accessories from
METREL. The instrument was designed on a basis of rich experience, acquired through
many years of dealing with electric installation test equipment.

The Eurotest instrument is professional, multifunctional, hand-held test instrument

intended to perform all the measurements required in order for a total inspection of
electrical installations in buildings. The following measurements and tests can be
performed:
 Voltage and frequency,
 Continuity tests,
 Insulation resistance tests,
 RCD testing,
 Fault loop / RCD trip-lock impedance measurements,
 Line impedance,
 Phase sequence,
 IMD testing (MI 3102 only),
 Resistance to earth (MI 3102 only),
 TRMS current (MI 3102 only),
 Illumination (MI 3102 only).

The large graphic matrix display with backlight offers easy to read results, indications,
measurement parameters and messages. The operation of the instrument is designed
to be as simple and clear as possible and no special training (except for the reading this
instruction manual) is required in order to begin using the instrument.

To become more familiar with how to perform measurements in general and in typical
applications, we recommend reading Metrel handbook Measurements on electric
installations in theory and practice.

The instrument is equipped with all accessories required in order to perform testing
comfortably. The soft carrying bag, included with the meter, protect the instrument and
keep all accessories together making it simple and easy to move between locations.

5
MI 3002 & MI3102 Safety and operational considerations

2 Safety and operational considerations

2.1 Warnings and notes
In order to maintain the highest level of operator safety while carrying out various tests
and measurements, Metrel recommends keeping your Eurotest instruments in good
condition and undamaged. When using the instrument, consider the following general
warnings:
 The symbol on the instrument means »Read the Instruction manual
with special care for safe operation«. The symbol requires an action!
 If the test equipment is used in a manner not specified in this user manual,
the protection provided by the equipment could be impaired!
 Read this user manual carefully, otherwise the use of the instrument may
be dangerous for the operator, the instrument or for the equipment under
test!
 Do not use the instrument or any of the accessories if any damage is
noticed!
 If a fuse blows in the instrument, follow the instructions in this manual in
order to replace it!
 Consider all generally known precautions in order to avoid risk of electric
shock while dealing with hazardous voltages!
 Do not use the instrument in supply systems with voltages higher than
550 V!
 Service intervention or adjustment is only allowed to be carried out by a
competent authorized personnel!
 Use only standard or optional test accessories supplied by your
distributor!
 Consider that older accessories and some of the new optional test
accessories compatible with this instrument only meet CAT III / 300 V
overvoltage safety rating! This means that maximal allowed voltage
between test terminals and ground is 300 V!
 The instrument comes supplied with rechargeable Ni-Cd or Ni-MH battery
cells. The cells should only be replaced with the same type as defined on
the battery compartment label or as described in this manual. Do not use
standard alkaline battery cells while the power supply adapter is
connected, otherwise they may explode!
 Hazardous voltages exist inside the instrument. Disconnect all test leads,
remove the power supply cable and switch off the instrument before
removing battery compartment cover.
 Do not connect any voltage source on CLAMP CURRENT input. It is
intended only for connection of current clamp with current output. The
Maximum continuous input current is 30 mA!
 All normal safety precautions must be taken in order to avoid risk of
electric shock while working on electrical installations!

6
MI 3002 & MI3102 Safety and operational considerations

Warnings related to measurement functions

Insulation resistance
 Insulation resistance measurement should only be performed on de-energized
objects!
 When measuring the insulation resistance between installation conductors, all
loads must be disconnected and all switches closed!
 Do not touch the test object during the measurement or before it is fully
discharged! Risk of electric shock!
 When an insulation resistance measurement has been performed on a capacitive
object, automatic discharge may not be done immediately! The warning message
and the actual voltage is displayed during discharge until voltage drops below
10 V.
 Do not connect test terminals to external voltage higher than 550 V (AC or DC) in
order not to damage the test instrument!

Continuity functions
 Continuity measurements should only be performed on de-energized objects!
 Parallel impedances or transient currents may influence test results.

Testing PE terminal
 If phase voltage is detected on the tested PE terminal, stop all measurements
immediately and ensure the cause of the fault is eliminated before proceeding
with any activity!

Notes related to measurement functions

General
 The indicator means that the selected measurement cannot be performed
because of irregular conditions on input terminals.
 Insulation resistance, continuity functions and earth resistance measurements
can only be performed on de-energized objects.
 PASS / FAIL indication is enabled when limit is set. Apply appropriate limit value
for evaluation of measurement results.
 In the case that only two of the three wires are connected to the electrical
installation under test, only voltage indication between these two wires is valid.

Insulation resistance
 If voltages of higher than 10 V (AC or DC) are detected between test terminals,
the insulation resistance measurement will not be performed.

Continuity functions
 If voltages of higher than 10 V (AC or DC) are detected between test terminals,
the continuity resistance test will not be performed.
 Before performing a continuity measurement, where necessary, compensate test
lead resistance.

7
MI 3002 & MI3102 Safety and operational considerations

RCD functions
 Parameters set in one function are also kept for other RCD functions!
 The measurement of contact voltage does not normally trip an RCD. However,
the trip limit of the RCD may be exceeded as a result of leakage current flowing
to the PE protective conductor or a capacitive connection between L and PE
conductors.
 The RCD trip-lock sub-function (function selector switch in LOOP position) takes
longer to complete but offers much better accuracy of fault loop resistance (in
comparison to the R L sub-result in Contact voltage function).
 RCD trip-out time and RCD trip-out current measurements will only be performed
if the contact voltage in the pre-test at nominal differential current is lower than
the set contact voltage limit!
 The autotest sequence (RCD AUTO function) stops when trip-out time is out of
allowable time period.

Fault loop / RCD trip-lock impedance

 The low limit prospective short-circuit current value depends on fuse type, fuse
current rating, fuse trip-out time and impedance scaling factor.
 The specified accuracy of tested parameters is valid only if the mains voltage is
stable during the measurement.
 Fault loop impedance measurements will trip an RCD.
 The measurement of fault loop impedance using trip-lock function does not
normally trip an RCD. However, the trip limit may be exceeded as a result of
leakage current flowing to the PE protective conductor or a capacitive connection
between L and PE conductors.

Line impedance
 The low limit prospective short-circuit current value depends on fuse type, fuse
current rating, fuse trip-out time and impedance scaling factor.
 The specified accuracy of tested parameters is valid only if the mains voltage is
stable during the measurement.

Resistance to earth (MI 3102 only)

 If voltage between test terminals is higher than 30 V, the resistance to earth
measurement will not be performed.
 If a noise voltage higher than approx. 5 V is present between the H and E or S test
terminals, the “ ” (noise) warning symbol will be displayed, indicating that the
test result may be incorrect!

TRMS current (MI 3102 only)

 Use only a test clamp supplied by Metrel or another clamp with similar
characteristics (current output, ratio, range). Consider the error of the test clamp
when evaluating measured results!
 Metrel A 1074 and A 1019 current clamps are suitable for use with the MI 3102
EurotestXE instrument in range 0.2 A  200 A. Below 0.2 A they can be used as
indicator only. They are not suitable for leakage current measurements.

8
MI 3002 & MI3102 Safety and operational considerations

Illumination (MI 3102 only)

 For accurate measurement make sure that the milk glass bulb is lit without any
shadows being cast on it (e.g. by hand, body or other unwanted objects etc).
 It is very important to know that the artificial light source has reach full power/
illuminance (see technical data of light source for time periods) and should be
therefore switched on for this period of time before any measurements are taken.

Testing the PE terminal

 The PE terminal can only be tested in the RCD, LOOP and LINE functions!
 For correct testing of PE terminal, the TEST key has to be touched for a few
seconds.
 Make sure to stand on non-isolated floor while carrying out the test, otherwise the
test result may be wrong!

2.2 Batteries

 When connected to an installation, the instruments battery compartment can

contain hazardous voltage inside! When replacing battery cells or before
opening the battery/fuse compartment cover, disconnect any measuring
accessory connected to the instrument and turn off the instrument,
 Ensure that the battery cells are inserted correctly otherwise the instrument will
not operate and the batteries could be discharged.
 If the instrument is not to be used for a long period of time, remove all batteries
from the battery compartment.
 Alkaline or rechargeable Ni-Cd or Ni-MH batteries (size AA) can be used. Metrel
recommends only using rechargeable batteries with a capacity of 2100mAh or
above.
 Do not recharge alkaline battery cells!

2.3 Charging
The batteries will begin charging whenever the power supply adapter is connected to
the instrument. The built-in protection circuits control the charging procedure and assure
maximum battery lifetime. The power supply socket polarity is shown in figure 2.1.
- +

Figure 2.1: Power supply socket polarity

Note:
 Use only power supply adapter delivered from the manufacturer or distributor of
the test equipment to avoid possible fire or electric shock!

9
MI 3002 & MI3102 Safety and operational considerations

2.4 Precautions on charging of new battery cells or cells

unused for a longer period
Unpredictable chemical processes can occur during the charging of new battery cells or
cells that have been left unused for long periods of time (more than 3 months). Ni-MH
and Ni-Cd cells can be subject to these chemical effects (sometimes called the memory
effect). As a result the instrument operation time can be significantly reduced during the
initial charging/discharging cycles of the batteries.

In this situation, Metrel recommend the following procedure to improve the battery
lifetime:
 Completely charge the batteries for at least 14h via the instrument built-in
charger.
 Completely discharge the batteries (this can be performed by using the
instrument normally until the instrument is fully discharged).
 Repeat the charge/discharge cycle at least 2-4 times in order to restore the
batteries to their normal capacity..

When using an external intelligent battery charger, one complete discharging/charging

cycle can be performed automatically. After performing this procedure, a normal battery
capacity should be fully restored and the operating time of the instrument will
approximately meet the data set out in the in the technical specification.

Notes:
 The charger in the instrument is a pack cell charger. This means that the cells
are connected in series during the charging so all of them must be in similar state
(similarly charged, same type and age).
 If even one deteriorated battery cell (or just one of a different type e.g. capacity,
chemical design) can cause disrupted charging of the entire battery pack which
could lead to overheating of the battery pack and a significant decrease in the
operating time.
 If no improvement is achieved after performing several charging/discharging
cycles, the state of each individual battery cells should be determined (by
comparing battery voltages, checking them in a cell charger, etc). It is very likely
that one or more of the battery cells could have deteriorated.
 The effects described above should not be mixed with the normal battery
capacity decrease over time. All charging batteries lose some of their capacity
when repeatedly charged/discharged. The actual decrease in capacity compared
to the number of charging cycles depends on the battery type. This information
is normally provided in the technical specification from battery manufacturer.

10
MI 3002 & MI3102 Safety and operational considerations

2.5 Standards applied

The EurotestDL and EurotestXE instruments are manufactured and tested in
accordance with the following regulations:
Electromagnetic compatibility (EMC)
BS EN 61326 Electrical equipment for measurement, control and laboratory
use – EMC requirements
Class B (Hand-held equipment used in controlled EM
environments)
Safety (LVD)
BS EN 61010-1 Safety requirements for electrical equipment for measurement,
control and laboratory use – Part 1: General requirements
BS EN 61010- Safety requirements for hand-held probe assemblies for electrical
031 measurement and test
BS EN 61010-2- Safety requirements for electrical equipment for measurement,
032 control, and laboratory use - Part 2-032: Particular requirements
for hand-held and hand-manipulated current sensors for electrical
test and measurement
Functionality
BS EN 61557 Electrical safety in low voltage distribution systems up to 1000
V AC and 1500 V AC – Equipment for testing, measuring or
monitoring of protective measures
Part 1 ......... General requirements
Part 2 ......... Insulation resistance
Part 3 ......... Loop resistance
Part 4 ......... Resistance of earth connection and equipotential
bonding
Part 5 ......... Resistance to earth (MI 3102 only)
Part 6 ......... Residual current devices (RCDs) in TT and TN
systems
Part 7 ......... Phase sequence
Part 10........ Combined measuring equipment
DIN 5032 Photometry
Part 7 ......... Classification of illuminance meters and luminance
meters
Other reference standards for testing RCDs
BS EN 61008 Residual current operated circuit-breakers without integral
overcurrent protection for household and similar uses
BS EN 61009 Residual current operated circuit-breakers with integral
overcurrent protection for household and similar uses
EN 60364-4-41 Electrical installations of buildings
Part 4-41 .... Protection for safety – protection against electric
shock
BS 7671 IEE Wiring Regulations (17th edition)
Note about EN and IEC standards:
 Text of this manual contains references to European and British standards. All
standards of EN 6XXXX (e.g. EN 61010) series are equivalent to IEC standards
with the same number (e.g. IEC 61010) and differ only in amended parts required
by European harmonization procedure.

11
MI 3002 & MI3102 Instrument operation

3 Instrument description
3.1 Front panel
3

6 7 1
Figure 3.1: Front panel

Legend:
1........ ON/OFF key, to switch the instrument on and off.
The instrument will automatically switch off 10 minutes after the last key press /
function switch rotation.
2........ Function selector switch.
3........ MEM key, to access memory operations.
4 ........ HELP/CAL key, to access help menus. CAL function can be used to
compensate for the test lead resistance in low-value resistance
measurements.
5........ Jogger keypad with cursors for navigating screen menus and TEST keys for
starting tests.
The TEST key also acts as the PE touching electrode which detects potentially
dangerous voltages appearing on the PE conductor.
6……. BACKLIGHT and CONTRAST key. This is used to turn the backlight on and off
and for adjusting the level of the contrast.
The high level backlight is automatically shut off 20 seconds after the last key
press / function switch rotation in order to extend service life of the battery.
7........ 128  64 dots matrix display with backlight.

12
MI 3002 & MI3102 Instrument description

3.2 Connector panel

1 2 3 4

> 550V
5

6
Figure 3.2: Connector panel

Legend:
1........ Test connector.
Warning! Maximum allowed voltage between test terminals and ground is
600V! Maximal allowed voltage between test terminals is 550 V!

MI 3102 only: In the earth resistance function, the test connector terminals are
used as follows:
 N/L2 blue test lead is used for the earth electrode (E).
 L/L1 black test lead is used for the auxiliary earth electrode (H).
 PE/L3 green test lead is used for the probe (S).

2........ Power supply socket.

3........ RS 232 connector
4........ Protection connector cover.
5........ USB connector
6........ CLAMP CURRENT input (MI 3102 only).
Warning! Do not connect any voltage source to the current clamp input. It is
intended for the connection of current clamps with current output only. The
maximum continuous input current is 30 mA!

13
MI 3002 & MI3102 Instrument description

3.3 Back panel

3

1 2

Figure 3.3: Back panel

Legend:
1........ Battery/fuse compartment cover.
2........ Information label.
3........ Fixing screws for battery/fuse compartment cover.

2
1
3

Fuse Fuse
F2 F1
F3
Fuse S/N XXXXXXXX

SIZE AA SIZE AA SIZE AA

SIZE AA SIZE AA SIZE AA

4 6
5

Figure 3.4.: Battery and fuse compartment

14
MI 3002 & MI3102 Instrument description

Legend:
1........ Fuse F1.
2........ Fuse F2.
3........ Fuse F3.
4........ Serial number label.
5........ Battery cells (size AA).
6........ Battery holder.

3.4 Bottom view

2 1

Continuity (EN 61557-4) RCD (EN 61557-6)

Low Contact voltage
R: 0.00   1999 

3
UC: 0.00V  100.0V
Test current: min. ±200mA RS : 0.00  10.00k(RS =UC / IN)
Open-circuit voltage: 5.4VDC  9.0VDC
Continuity 7mA Fault loop resistance (without tripping RCD)
RS : 0.00  10k
R: 0.0  1999
Test current: max. 7mA DC UC: 0.00V  100.0V, (UC=RS  I N)
Open-circuit voltage: 5.4VDC  7.2VDC
Tripping time
Insulation resistance (EN 61557-2) non-delayed (time-delayed) RCDs
R: 0.000M   199.9M  , U N=100V DC, 250V DC t: 0ms  300ms (500ms)
R: 0.000M   999M , U N= 500V DC, 1kV DC t: 0ms  150ms (200ms)
U: 0V  1200V, t: 0ms  40ms (150ms)
Nominal voltages: 100V DC, 250V DC, 500V DC, 1kV DC UC: 0.00V  100.0V
Measuring current: min. 1mA at R N=U N 1k  /V Tripping current
Short-circuit current: <3mA DC I: 0.2  IN  1.1 IN
Line resistance t: 0ms  300ms
R L-N (L): 0.00   1999  UC: 0.00V  100.0V
IPSC: 0.06A  24.4kA
IN : 10mA, 30mA, 100mA, 300mA, 500mA, 1A
Nominal voltage: 100V AC  440V AC / 45Hz 65Hz
Multiplier:  1/2  1,  2,  5
Fault loop resistance (EN 61557-3) Nominal voltage: 100VAC  264VAC / 45Hz  65Hz
R L-PE: 0.00   1999
IPFC: 0.06A  24.4kA Phase rotation (EN 61557-7)
Nominal voltage: 100V AC  440V AC / 45Hz 65Hz Nominal voltage: 100V AC  440V AC / 45Hz  65Hz
Voltage, frequency Results: 1.2.3. or 2.1.3
U: 0V  440V
f: 45Hz  65Hz

Figure 3.5: Bottom view

Legend:
1........ Information label.
2........ Neck strap openings.
3........ Handling side covers.

15
MI 3002 & MI3102 Instrument description

3.5 Carrying the instrument

The neck strap supplied in standard set allows the instrument to be carried in a variety
of different ways.. The operator can choose the most appropriate method based on the
tasks they are performing. See the following examples:

The instrument can be

hung around operator's
neck allowing the
instrument to move
freely. This allows
equipment to be moved
quickly between test
locations.

The instrument can be used from inside the

soft carrying case – test cables can be
connected to the instrument through the front
flap of the carry case.

16
MI 3002 & MI3102 Instrument operation

4 Instrument operation
4.1 Meaning of symbols and messages on the instrument display
The instrument display is divided into four sections:
1

4 3

Figure 4.1: Display outlook

Legend:
1........ Function and parameter line.
In the top line of the display, the measuring function/sub-function and
parameters are displayed.
2........ Result field.
In this field the main result and sub-results together with the
PASS/FAIL/ABORT status are displayed.
3........ Online voltage and output monitor.
4........ Message field.

4.1.1 The online voltage and output terminal monitor

Online voltages are displayed together with test terminal
indication. All three test terminals are used for selected
measurement.
Online voltages are displayed together with test terminal
indication. L and N test terminals are used for selected
measurement.

Polarity of test voltage applied to the output terminals, L

and N.

Unknown supply system.

L – N polarity changed.

fr Frequency out of range.

17
MI 3002 & MI3102 Instrument operation

4.1.2 Message field – battery status

Battery power indication.

Low battery indication. Battery pack is too weak to

guarantee correct result. Replace the batteries.
Recharging is running (if power supply adapter is
connected).

4.1.3 Message field – measurement warnings/messages

Warning! High voltage is applied to the test terminals.

Warning! Phase voltage on the PE terminal! Stop all the

measurements immediately and eliminate the fault before
proceeding with any activity!

Measurement is running. Consider any displayed

warnings!

Measurement can be performed after pressing the TEST

key. Consider any displayed warning after starting the
measurement!

Measurement prohibited. Consider any displayed

warnings and check online voltage/terminal monitor!

Test leads resistance in low-value resistance

Co
measurement is compensated.
RCD tripped during the measurement. The trip limit may
be exceeded as a result of leakage current flowing to the
PE protective conductor or capacitive connection
between L and PE conductors.

RCD not tripped during the measurement.

Instrument overheated. Temperature of internal

components in the instrument reached top limit.
Measurement is prohibited until the temperature is lower
then that limit.
Battery capacity is too low to guarantee correct result.
Replace the batteries.

18
MI 3002 & MI3102 Instrument operation

Fuse F1 (continuity circuit) blown or not inserted.

SF Single fault condition in IT system.

Noise voltage is present between H and E or S test

terminals.
MI 3102 only:
Resistance of auxiliary earth electrode is higher than
100R E . Check the auxiliary earth electrode.
Probe resistance is higher than 100R E . Check the
probe.
Resistances of auxiliary earth electrode and probe are
higher than 100R E . Check all probes.

4.1.4 Result field

Measurement passed.

Measurement failed.

Measurement is aborted. Check the conditions at the

input terminal.

4.1.5 Other messages

Instrument settings and measurement parameters/limits
Hard Reset are set to initial (factory) values. For more information
refer to chapter 4.5.4 Recalling original settings.
LUXmeter probe is turned off or disconnected from the
No probe EurotestXE instrument. Connect probe to the instrument
using RS232 connector and turn it on (MI 3102 only).
First measurement First stored measurement results are displayed.
Last measurement Last stored measurement results are displayed.
Memory full All memory locations are occupied.
Already saved Measurement results already saved.
Memory contents damaged. Contact your distributor or
CHECK SUM ERROR
manufacturer for further information.

19
MI 3002 & MI3102 Instrument operation

4.1.6 Sound warnings

Pressed key deactivated.
The shortest sound
Sub-function is not available.
Pressed key activated.
Measurement has been started after pressing the TEST
Short sound
key. Consider any displayed warnings during
measurement.
Measurement is prohibited. Consider any displayed
Long sound
warnings and check online voltage/terminal monitor!
Warning! Phase voltage on the PE terminal! Stop all the
Periodic sound measurements immediately and eliminate the fault before
proceeding with any activity!

4.1.7 Function and parameter line

1
2 3

Figure 4.2: Function selector switch and belonging parameter line

Legend:
1……Main function name.
2……Function or sub-function name.
3……Measuring parameters and limit values.

4.2 Selecting measurement function/ subfunction

The following measurements can be selected with the function selector switch:
 Voltage and frequency,
 Insulation resistance,
 Low-value resistance,
 RCD testing,
 Fault loop impedance,
 Line impedance,
 Phase sequence,
 Resistance to earth (MI 3102 only),
 TRMS current (MI 3102 only),
 Illumination (MI 3102 only).
The function/sub-function name is highlighted on the display by default.
Sub-function can be selected by using  and  keys in function/parameter line.

20
MI 3002 & MI3102 Instrument operation

4.3 Setting measurement parameters and limits

By using  and  keys select the parameter/limit value you want to edit. By using 
and  keys the selected parameter can be set.

Once the measurement parameters are set, the settings are retained until new changes
are made or the original settings are recalled.

4.4 Help menu

Help menus are available in all functions. The Help menu contains schematic diagrams
for illustrating how to properly connect the instrument to electric installation. After
selecting the measurement you want to perform, press the HELP key in order to view
the associated Help menu.
Press the HELP key again to see further Help screens (if available) or to return to the
function menu.

Figure 4.3: Example of help menu

4.5 Setup menu

In the Setup menu, the following actions can be taken:
 Supply system selection,
 Impedance scaling factor adjustment,
 Language selection,
 Communication port settings
 Support for remote commanders.

To enter the Setup menu press the BACKLIGHT key and rotate function selector switch
in any direction at the same time.

Rotate function selector switch again to leave Setup menu or setup sub-menus.

Figure 4.4: Setup menu

21
MI 3002 & MI3102 Instrument operation

4.5.1 Supply system setup

The instrument enables tests and measurements in the following supply systems:
 TN (TT) system,
 IT system,
 Reduced low voltage system (255 V),
 Reduced low voltage system (363 V).

Select SYSTEMS in the Setup menu by using  and  keys and press the TEST key
to enter the Supply system setup menu.

Figure 4.5: Supply systems selecting menu

By using  and  keys select supply system and press the TEST key to accept the
setting.

4.5.2 Impedance scaling factor adjustment

Select SET Z FACTOR in Setup menu by using  and  keys and press the TEST key
to enter the Impedance scaling factor adjustment menu.

Figure 4.6: Scaling factor adjustment menu

Use the  and  keys to adjust the scaling factor and press the TEST key to accept the
new setting.
The impedance limit values for different overcurrent protective devices are scaled down
by a factor 0,8 or 0,75 (Z factor). This means that the fault current will still be high
enough also at increased conductor temperatures and low supply voltage. This assures
a safe operation of the overcurrent protection device in all conditions.

22
MI 3002 & MI3102 Instrument operation

4.5.3 Language selection

Select SET LANGUAGE in Setup menu by using the  and  keys and press the
TEST key to enter the Language selection menu.

Figure 4.7: Language selecting menu

By using  and  keys select the language you want to use and press The TEST key
to accept the new setting.

4.5.4 Communication port selection

Use the  and  keys in the Setup menu to highlight the SET COMMUNICATION
PORT option and press the TEST key to enter the Communication menu.

> RS 232 <9600>

USB 115200

Figure 4.8: Communication menu

By using the  and  keys, select communication port you want to use. If the RS232
communication port is selected, use  and  keys to select baud rate (The USB port
has a baud rate set to 115200 bps). Press the TEST key to accept the new setting.

Note:
 Only one port can be active at one time.

4.5.5 Plug / Tip commander support

Select COMMANDER in the Setup menu by using the  and  keys and press the
TEST key to enable / disable the support for remote commanders.

If disable is selected, then keys on the Plug / Tip commander are disabled (except
backlight key). This implies that the selected test can only be started (or results can be
saved) using the keys on the instrument.
If enable is selected, the keys on Plug / Tip commander are activated and tests can be
started and results saved either from the buttons on the instrument or the buttons on the
remote commanders.

Note:
 This option is intended to disable the commander’s remote keys. In the case of
high EM interfering noise the operation of the commander’s key can be irregular.

23
MI 3002 & MI3102 Instrument operation

4.5.6 Recalling original settings

The following parameters and settings can be automatically set back to initial (factory)
values:
 Test parameters and limit values,
 Contrast,
 Impedance scaling factor,
 Supply system,
 Communication port
 Support for remote commanders.

In order to restore the original setting of the instrument, press and hold  key and
switch on the instrument (the external charger must not be connected). »Hard reset«
message will be displayed at start-up.

Instrument settings, measurement parameters and limits are set to their initial values as
follows:
Instrument settings Default value
Contrast 50 %
Impedance scaling factor 0.8
Supply system TN/TT
Communication RS232, 9600 bps
Commander Enabled

Function
Parameter / limit value
Sub-function
CONTINUITY
r1, r2,rN, R1+R2, R2 High limit resistance value: 2.0 

INSULATION
ISO L/N, ISO L/E, ISO N/E, ISO L/L Nominal test voltage: 500 V
Low limit resistance value: 1 M
LINE Fuse type: none selected (F)
Fuse current rating: none selected (A)
Fuse tripping current: none selected (ms)
LOOP Fuse type: none selected (F)
Zs Fuse current rating: none selected (A)
Zs (rcd) Fuse tripping current: none selected (ms)
RCD Selected function: RCD Uc
Contact voltage – RCD Uc Nominal differential current: I N =30 mA
Trip-out time – RCD t RCD type and test current starting polarity:
Trip-out current – RCD III G
Autotest – RCD AUTO Limit contact voltage: 50 V
Nominal differential current multiplier: 1
RESISTANCE TO EARTH High limit resistance value: 50 
(MI 3102 only)
ILLUMINATION (MI 3102 only) Low limit illumination value: 300 lux
TRMS CURRENT (MI 3102 only) Current limit: 4.5 mA

24
MI 3002 & MI3102 Instrument operation

4.6 Display contrast adjustment

When the low-level backlight is activated, press and hold the BACKLIGHT key until the
Display contrast adjustment menu is displayed.

Figure 4.9: Contrast adjustment menu

Use the  and  keys to adjust the contrast level and, when satisfied, press the TEST
key to accept the new setting.

25
MI 3002 & MI3102 Measurements

5 Measurements
5.1 Insulation resistance
The Insulation resistance measurement is performed in order to ensure safety against
electric shock. Using this measurement the following items can be determined:
 Insulation resistance between installation conductors,
 Insulation resistance of non-conductive rooms (walls and floors),
 Insulation resistance of ground cables,
 Resistance of semi-conductive (antistatic) floors.

For additional information concerning insulation resistance measurements refer to

Metrel’s handbook Measurements on electric installations in theory and practice.

Four Insulation resistance sub-functions are available:

 ISO L/E,
 ISO L/N
 ISO L/L
 ISO N/E

The insulation resistance tests are carried out in the same way regardless which sub-
functions is selected. However it is important to select the appropriate sub-function in
order to classify the measurement to be correctly considered in verification documents
(Electrical Installation Certificate, Periodic Inspection Report etc.).

How to perform an insulation resistance measurement

Step 1 Select Insulation function with the function selector switch and sub-function
with the / keys .The following menu is displayed:

Figure 5.1: Insulation resistance measurement menu

Step 2 Set the following measuring parameter and limit values:

 Nominal test voltage,
 Low limit resistance value.

Step 3 Ensure that no voltages are present on the item for testing. Connect the test
leads to the Eurotest instrument, Connect the test cables to the item under
test. (see figure 5.2) to perform insulation resistance measurement. Use the
Help function if necessary for further reference.

26
MI 3002 & MI3102 Measurements

Figure 5.2: Connection of universal test cable and tip commander

Step 4 Check the displayed warnings and online voltage/terminal monitor before
starting the measurement. If OK, press and hold the TEST key until the result
has stabilised. Actual measured results are shown on the display during
measurement.
After the TEST key is released the last measured results are displayed,
together with the PASS/FAIL indication (if applicable).

Figure 5.3: Example of insulation resistance measurement results

Displayed results:
R .............Insulation resistance,
Um..........Actual voltage applied to item under test

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.
Warnings:
 Insulation resistance measurement should only be performed on de-energized
objects!
 When measuring the insulation resistance between installation conductors, all
loads must be disconnected and all switches closed!
 Do not touch the test object during the measurement or before it is fully
discharged! Risk of electric shock!
 When an insulation resistance measurement has been performed on a capacitive
object, an automatic discharge may not be done immediately! The warning
message and actual voltage is displayed during discharge until the voltage of
the item under test drops below 10 V.
 In order to prevent damaging the test instrument, do not connect test terminals to
an external voltage higher than 600 V (AC or DC)
Note:
 If a voltage higher than 10 V (AC or DC) appears between the test terminals, the
insulation resistance measurement will not be performed.

27
MI 3002 & MI3102 Measurements

5.2 Continuity
This function is used to test the resistance between two different points of the
installation to ensure that a conductive path exists between them. The test ensures that
all protective conductors, earth conductors or bonding conductors are correctly
connected, terminated and have the correct resistive value.
The Continuity measurement is performed with a test current of more than 200mA. An
automatic pole reversal of the test voltage and the test current is performed during the
test. This test checks for any components (e.g. diodes, transistors, SCRs) that may
have a rectifying effect on the circuit which could cause problems when a voltage is
applied.

This measurement completely complies with EN61557-4 regulations.

Five Continuity sub-functions are available:
 r1,
 rN
 r2
 R 1 +R 2
 R2
The continuity tests are carried out in the same way regardless of which sub-functions is
selected. However it is important to select the appropriate sub-function in order to
classify the measurement to be correctly considered in verification documents
(Electrical Installation Certificate, Periodic Inspection Report etc.).

How to perform a Continuity resistance measurement

Step 1 Select the Continuity function with the function selector switch and the sub-
function with the / keys. The following menus will be displayed:

Figure 5.4: Continuity measurement menu (example for sub-function R1+R2)

Step 2 Set the following limit value:

 High limit resistance value.

Step 3 Connect test cable to the Eurotest instrument. Before performing a Continuity
measurement, compensate for the test leads resistance as follows:

28
MI 3002 & MI3102 Measurements

1. Short test leads first as shown in figure 5.5.

N/L2
PE/L3 N/L2
PE/L3
L/L1 L/L1
prolongation lead

Figure 5.5: Shorted test leads

2. Press the TEST key in order to perform regular measurement. The

displayed result should be close to 0.00 .(depending on the length of test
leads used).
3. Press the CAL key. After performing test leads compensation the
compensated test leads indicator Co will be displayed on the top line.
4. In order to remove any test lead resistance compensation, follow the
procedure described in step3 with test leads separated from one another.
After removing any test lead compensation, the compensation indicator
will disappear from the top line of the display.

The compensation of the test leads can be carried out in any of the Continuity
sub-functions (r1, r2, rN, R1+R2, R2). The compensation value will then be
transferred to all other subfunctions.

Step 4 Ensure that the item for testing is disconnected from any voltage source.
Connect the test cables to the item under test. Follow the connection
diagrams shown in figures 5.6 and 5.8 to perform a Continuity measurement.
Use the Help function if necessary.

r1 rN r2
Figure 5.6: Connection for testing the r1, rN, and r2 sections of the wiring

29
MI 3002 & MI3102 Measurements

Figure 5.7: Connection for testing the R2 section of the wiring and bonding connections

Figure 5.8: Connection for testing the R1+R2 section of the wiring

Step 5 Check for any warnings and the online voltage/terminal monitor on the
display before starting the measurement. If everything is OK, press the TEST
key. After performing the measurement, the results appear on the display
together with the PASS/FAIL indication (if applicable).

Figure 5.9: Examples of Continuity measurement results

Displayed results:
R .............Main Continuity result (average of R+ and R- results),

30
MI 3002 & MI3102 Measurements

R+...........Resistance sub-result with positive voltage at L terminal,

R-............Resistance sub-result with positive voltage at N terminal.

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Warnings:
 Low-value resistance measurements should only be performed on de-energized
objects!
 Parallel impedances or transient currents may influence test results.

Note:
 If voltage between test terminals is higher than 10 V the measurement will not be
performed.

5.3 Testing RCDs

When testing RCDs, the following sub-functions can be performed:
 Contact voltage measurement,
 Trip-out time measurement,
 Trip-out current measurement,
 RCD autotest.
In general the following parameters and limits can be set when testing RCDs:
 Limit contact voltage,
 Nominal differential RCD trip-out current,
 Multiplier of nominal differential RCD trip-out current,
 RCD type,
 Test current starting polarity.

5.3.1 Limit contact voltage

Safety contact voltage is limited to 50 V AC for standard domestic area. In special

environments (hospitals, wet places, etc.) contact voltages up to 25 V AC are permitted.
Limit contact voltage can be set in contact voltage Uc function only!

5.3.2 Nominal differential trip-out current

Nominal differential current is the rated trip-out current of an RCD. The following RCD
current ratings can be set: 10 mA, 30 mA, 100 mA, 300 mA, 500 mA and 1000 mA.

5.3.3 Multiplier of nominal residual current

Selected nominal differential current can be multiplied by ½, 1, 2 or 5.

31
MI 3002 & MI3102 Measurements

5.3.4 RCD type and test current starting polarity

The Eurotest instrument enables testing of general (non-delayed) and selective (time-
delayed, marked with the S symbol). The types of RCD the instrument is suitable for
testing include:
 Alternating residual current (AC type, marked with symbol),
 Pulsating DC residual current (A type, marked with symbol).
Test current starting polarity can be started with the positive half-wave at 00 or with the
negative half-wave at 1800.

positive start polarity negative start polarity

(0°) (180°)
Figure 5.10: Test current started with the positive or negative half-wave

5.3.5 Testing selective (time-delayed) RCDs

Selective RCDs demonstrate delayed response characteristics. Trip-out performance is
influenced due to pre-loading during measurement of contact voltage. In order to
eliminate the pre-loading a time delay of 30 s is inserted before performing the trip-out
test.

5.3.6 Contact voltage

Leakage current flowing to the PE terminal causes a voltage drop across earth
resistance, which is called contact voltage (Uc). This voltage is present on all accessible
parts connected to the PE terminal and should be lower than the safety limit voltage.
The parameter contact voltage is measured without tripping-out the RCD. R L is a fault
loop resistance and is calculated as follows:
UC
RL 
I N
Displayed contact voltage relates to the rated nominal differential current of the RCD
and is multiplied by a safety factor. See the table 5.1 for detailed contact voltage
calculation.
RCD type Contact voltage Uc
G
Uc  1.05I N
G
S
Uc  1.052I N
S
G
Uc  1.05 2 I N
G
S
Uc  1.052 2 I N
S
Table 5.1: Relationship between Uc and I N

32
MI 3002 & MI3102 Measurements

For additional general information concerning contact voltage measurement refer to

Metrel’s handbook Measurements on electric installations in theory and practice.

How to perform contact voltage measurement

Step 1 Select RCD function with the function selector switch first. Use the / keys to
select contact voltage function (Uc). The following menu will be displayed:

Figure 5.11: Contact voltage measurement menu

Step 2 Set the following measuring parameters and limit values:

 Nominal residual current,
 RCD type,
 Limit contact voltage.

Step 3 Connect the test leads to the instrument and follow the connection diagram
shown in figure 5.12 to perform contact voltage measurement. Use the Help
function if necessary.
L1
L2
L3
N
PE

L/L
PE/L3 1
N/L2
N PE L

Ro RE

Figure 5.12: Connection of plug test cable or universal test cable

Step 4 Check for any warnings and check the online voltage/terminal monitor on the
display before starting the measurement. If everything is ok, press the TEST
key. After performing the measurement, the results will be displayed along
with a PASS/FAIL indication.

Figure 5.13: Example of contact voltage measurement results

Displayed results:
U .............Contact voltage.
Rl ............Fault loop resistance.

33
MI 3002 & MI3102 Measurements

Lim .........Limit earth fault loop resistance value according to BS 7671.

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 Parameters set in this function are also kept for all other RCD functions!
 The measurement of contact voltage does not normally trip an RCD. However,
the trip limit may be exceeded as a result of leakage currents flowing through the
PE protective conductor or a capacitive connection between the L and PE
conductor.
 RCD trip-lock sub-function (function selector switch in LOOP position) takes
longer to complete but offers much better accuracy of a fault loop resistance
result (in comparison with the R L sub-result in Contact voltage function).

34
MI 3002 & MI3102 Measurements

5.3.7 Trip-out time

Trip-out time measurement is used to verify the effectiveness of an RCD. This is
achieved by a test simulating an appropriate fault condition. Trip-out times vary between
standards and are listed below.
Trip-out times according to BS EN 61008 / BS EN 61009:
½I N *) I N 2I N 5I N
General (non- t  > 300 ms t  < 300 ms t  < 150 ms t  < 40 ms
delayed) RCDs
Selective (time- t  > 500 ms 130 ms < t  < 60 ms < t  < 50 ms < t  <
delayed) RCDs 500 ms 200 ms 150 ms
Trip-out times according to BS 7671:
½I N *) I N 2I N 5I N
General (non- t  > 1999 ms t  < 300 ms t  < 150 ms t  < 40 ms
delayed) RCDs
Selective (time- t  > 1999 ms 130 ms < t  < 60 ms < t  < 50 ms < t  <
delayed) RCDs 500 ms 200 ms 150 ms
*)
Test current of ½I N cannot cause trip-out of the RCDs.
For additional information concerning trip-out time measurement refer to the Metrel
handbook Measurements on electric installations in theory and practice.

How to perform trip-out time measurement

Step 1 Select the RCD function with the function selector switch and use the /
keys to select the Trip-out time function (RCDt). The following menu will be
displayed:

Figure 5.14: Trip-out time measurement menu

Step 2 Set the following measuring parameters:

 Nominal differential trip-out current,
 Nominal differential trip-out current multiplier,
 RCD type, and
 Test current starting polarity.

Step 3 Connect the leads to the instrument and follow the connection diagram shown
in figure 5.12 (see the chapter 5.3.6 Contact voltage) to perform trip-out time
measurement.

Step 4 Check for any warnings and check the online voltage/terminal monitor on the
display before starting measurement. If everything is ok, press the TEST key.

35
MI 3002 & MI3102 Measurements

After performing the measurement, results will appear on the display along
with a PASS/FAIL indication.

Figure 5.15: Example of trip-out time measurement results

Displayed results:
t ..............Trip-out time,
U C ...........Contact voltage.

Save displayed results for documentation purposes. Refer to chapter 6.1.

Saving results (MI 3002 and MI 3102).

Notes:
 Parameters set in this function are also transferred onto all other RCD functions!
 RCD trip-out time measurement will be performed only if the contact voltage at
nominal differential current is lower than the limit set in the contact voltage
setting!
 The measurement of the contact voltage in pre-test does not normally trip an
RCD. However, the trip limit may be exceeded as a result of leakage current
flowing through the PE protective conductor or a capacitive connection between
L and PE conductors.

5.3.8 Trip-out current

This test is used to determine the minimum current required to trip the RCD. After the
measurement has been started, the test current generated by the instrument is
continuously increased, starting at 0.2I N to 1.1I N (to 1.5I N / 2.2I N (I N =10 mA)
for pulsating DC residual currents), until the RCD trips.
For additional information concerning the trip-out current measurement, refer to Metrel’s
handbook Measurements on electric installations in theory and practice.

How to perform trip-out current measurement

Step 1 Select RCD function with the function selector and use the / keys to select
the Trip-out current (RCD ) function. The following menu is displayed:

Figure 5.16: Trip-out current measurement menu

36
MI 3002 & MI3102 Measurements

Step 2 By using cursor keys the following parameters can be set in this
measurement:
 Nominal residual current,
 RCD type,
 Test current starting polarity.

Step 3 Connect the test leads to the instrument and follow the connection diagram
shown in figure 5.12 (see the chapter 5.3.6 Contact voltage) to perform trip-
out current measurements. Use the Help function if necessary.

Step 4 Check for any warnings and check the online voltage/terminal monitor shown
on the display before starting the measurement. If everything is ok, press the
TEST key. After performing the measurement, the results will be displayed
along with a PASS/FAIL indication.

Figure 5.17: Example of trip-out current measurement result

Displayed results:
I  .............Trip-out current,
U Ci ..........Contact voltage,
tI .............Trip-out time.
Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 Parameters set in this function are also kept for other RCD functions!
 RCD trip-out current measurement will be performed only if the contact voltage at
nominal differential current is lower than set limit contact voltage!
 The measurement of contact voltage in the pre-test does not normally trip an
RCD. However, the trip limit may be exceeded as a result of leakage current
flowing through the PE protective conductor or a capacitive connection between
L and PE conductors.

5.3.9 Autotest
The purpose of the autotest function is to perform a complete RCD testing and
measurement of most important associated parameters (contact voltage, fault loop
resistance and trip-out time at different fault currents) with one press of a button. If a
faulty parameter is noticed during the autotest, the test will stop to highlight the need for
further investigation.
Notes:
 The measurement of contact voltage in the pre-test does not normally trip an RCD.
However, the trip limit may be exceeded as a result of leakage current flowing

37
MI 3002 & MI3102 Measurements

through the PE protective conductor or a capacitive connection between L and PE

conductors.
 The autotest sequence stops when the trip-out time is out of allowed time period.

5.3.9.1 How to perform RCD autotest

Step 1 Select RCD function with the function selector switch first. Use the / keys
to select RCD autotest function (AUTO). The following menu is displayed:

Figure 5.18: RCD autotest menu

Step 2 Set the following measuring parameters:

 Nominal differential trip-out current,
 RCD type.

Step 3 Connect the test leads to the instrument and follow the connection diagram
shown in figure 5.12 (also see the chapter 5.3.6 Contact voltage) to perform
the RCD autotest. Use the Help function if necessary.

Step 4 Check for any warnings and check the online voltage/terminal monitor
displayed on the screen before starting the measurement. If everything is ok,
press the TEST key. The autotest sequence will then start to run as follows:

1. Trip-out time measurement with the following measurement parameters:

 Test current of I N ,
 Test current started with the positive half-wave at 00.
Measurement normally trips an RCD within allowed time period. The following
menu is displayed:

Figure 5.19: Step 1 RCD autotest results

After re-activating the RCD, the autotest sequence automatically proceeds

with step 2.
2. Trip-out time measurement with the following measurement parameters:
 Test current of I N ,
 Test current started with the negative half-wave at 1800.
Measurement normally trips an RCD. The following menu is displayed:

38
MI 3002 & MI3102 Measurements

Figure 5.20: Step 2 RCD autotest results

After re-activating the RCD, the autotest sequence automatically proceeds

with step 3.

3. Trip-out time measurement with the following measurement parameters:

 Test current of 5I N ,
 Test current started with the positive half-wave at 00.
Measurement normally trips an RCD within allowed time period. The following
menu is displayed:

Figure 5.21: Step 3 RCD autotest results

After re-activating the RCD the autotest sequence automatically proceeds

with step 4.
4. Trip-out time measurement with the following measurement parameters:
 Test current of 5I N ,
 Test current started with the negative half-wave at 1800.
Measurement normally trips an RCD within allowed time period. The following
menu is displayed:

Figure 5.22: Step 4 RCD autotest results

After re-activating the RCD the autotest sequence automatically proceeds

with step 5.
5. Trip-out time measurement with the following measurement parameters:
 Test current of ½I N ,
 Test current started with the positive half-wave at 00.

39
MI 3002 & MI3102 Measurements

Measurement does not normally trip an RCD. The following menu is

displayed:

Figure 5.23: Step 5 RCD autotest results

After performing step 5 the RCD autotest sequence automatically proceeds

with step 6.
6. Trip-out time measurement with the following measurement parameters:
 Test current of ½I N ,
 Test current started with the negative half-wave at 1800.
Measurement does not normally trip an RCD. The following menu is
displayed:

Figure 5.24: Step 6 RCD autotest results

Displayed results:
x1 (left) ...... Step 1 trip-out time result, t3 (I N , 00),
x1 (right) .... Step 2 trip-out time result, t4 (I N , 1800),
x5 (left) ...... Step 3 trip-out time result, t5 (5I N , 00),
x5 (right) .... Step 4 trip-out time result, t6 (5I N , 1800),
x½ (left) ..... Step 5 trip-out time result, t1 (½I N , 00),
x½ (right) ... Step 6 trip-out time result, t2 (½I N , 1800),
Uc ...........Contact voltage.
Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Note:
 In case of testing the RCD type A with rated residual currents of In = 300 mA,
500 mA, and 1000 mA, the x5 Auto tests will be automatically skipped. In this
case, the auto test result passes if the t1 to t4 results pass, and on the display
are omitted t5 and t6.

40
MI 3002 & MI3102 Measurements

5.4 Fault loop impedance and prospective fault current

The loop impedance function has two sub-functions available:
Zs sub-function performs a fast fault loop impedance measurement on supply systems
which do not contain RCD protection.
Zs(rcd) trip-lock sub-function performs fault loop impedance measurement on supply
systems which are protected by RCDs..

5.4.1 Fault loop impedance

The fault loop impedance measures the impedance of the fault loop in the event that a
short-circuit to an exposed conductive parts occurs (i.e. a conductive connection occurs
between the phase conductor and protective earth conductor). In order to measure loop
impedance the instrument uses a high test current.
Prospective fault current (IPFC) is calculated on the basis of the measured resistance
as follows:
UN
I PFC 
Z L  PE

Where:
Nominal input voltage U N Voltage range
115 V (100 V  U L-PE  160 V)
230 V (160 V  U L-PE  264 V)

For additional information concerning fault loop impedance measurement refer to

Metrel’s handbook Measurements on electric installations in theory and practice.

5.4.1.1 How to perform fault loop impedance measurement

Step 1 Select the LOOP function with the function selector switch and use the /
keys to select the Zs sub-function. The following menu is displayed:

Figure 5.25: Loop impedance measurement menu

Step 2 Set the following measuring parameters:

 Fuse type,
 Fuse current rating,
 Fuse trip-out time,
 Impedance scaling factor (see chapter 4.5.2 Impedance scaling factor
adjustment).
The complete list of available fuse types can be found in Appendix A.

41
MI 3002 & MI3102 Measurements

Step 3 Connect the test leads to the instrument and follow the connection diagram
shown in the figure 5.26 to perform fault loop impedance measurement. Use
the Help function if necessary.

L1
L2
L3
N
PE

L/L
PE/L3 1
N/L2
N PE L

Ro RE

Figure 5.26: Connection of plug cable and universal test cable

Step 4 Check for any warnings displayed on the screen and check the online
voltage/terminal monitor before starting the measurement. If everything is ok,
press the TEST key. After performing the measurement, the test results will
appear on the display together with the PASS/FAIL indication (if applicable).

Figure 5.27: Example of loop impedance measurement results

Displayed results:
Z .............Fault loop impedance,
I SC ...........Prospective fault current (displayed in amps),
Lim .........High limit fault loop impedance value (if applicable).

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 The fault loop impedance limit depends on the fuse type, fuse current rating, fuse
trip-out time and Impedance scaling factor.
 The specified accuracy of test parameters is valid only if mains voltage is stable
during the measurement.
 The Zs Fault loop impedance measurement trips RCD protected circuits.

42
MI 3002 & MI3102 Measurements

5.4.2 The fault loop impedance test for RCD protected circuits
The fault loop impedance is measured with a low test current to avoid tripping the RCD.
This function can also be used for fault loop impedance measurement in system
equipped with RCDs which have a rated trip-out current of 10 mA and above.

Prospective fault current (IPFC) is calculated on basis of measured resistance as

follows:
UN
I PFC 
Z L  PE

Where:
Nominal input voltage U N Voltage range
115 V (100 V  U L-PE  160 V),
230 V (160 V  U L-PE  264 V),

For additional information concerning fault loop impedance measurement refer to

Metrel’s handbook Measurements on electric installations in theory and practice.

5.4.2.1 How to perform RCD trip-lock measurement

Step 1 Select the LOOP function with the function selector switch and use the /
keys to select Zsrcd sub-function. The following menu is displayed:

Figure 5.28: Trip-lock function menu

Step 2 Set the following measuring parameters:

 Fuse type,
 Fuse current rating,
 Fuse trip-out time,
 Impedance scaling factor (see chapter 4.5.2 Impedance scaling factor
adjustment).

The complete list of available fuse types can be found in Appendix A.

Step 3 Connect the appropriate test leads to the instrument and follow the
connection diagram shown in figure 5.12 to perform RCD trip-lock
measurement (see chapter 5.3.6 Contact voltage). Use Help function if
necessary.

43
MI 3002 & MI3102 Measurements

Step 4 Check for warnings on the display and check the online voltage/terminal
monitor before starting the measurement. If everything is ok, press the TEST
key. After performing the measurement the results will appear on the display.

Figure 5.29: Example of fault loop impedance measurement results using trip-lock
function

Displayed result:
Z .............Fault loop impedance,
I SC ...........Prospective fault current,
Lim .........High limit fault loop impedance value (if applicable).

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 The measurement of fault loop impedance using trip-lock function does not
normally trip an RCD. However, if the trip limit may be exceeded as a result of
leakage current flowing through the PE protective conductor or a capacitive
connection between L and PE conductors.

 The specified accuracy of test parameter is valid only if mains voltage is stable
during the measurement.

44
MI 3002 & MI3102 Measurements

5.5 Line impedance and prospective short-circuit current

The line impedance is a measurement of the impedance of the current loop when a
short-circuit to the neutral conductor occurs (conductive connection between phase
conductor and neutral conductor in single-phase system or between two phase
conductors in three-phase system). A high test current is used to perform the line
impedance measurement.
Prospective short circuit current is calculated as follows:
UN
I PSC 
Z L N ( L)

Where:
Nominal input voltage U N Voltage range
115 V (100 V  U L-PE  160 V)
230 V (160 V  U L-PE  264 V)
400 V (264 V  U L-PE  440 V)

For additional information concerning line impedance refer to Metrel’s handbook

Measurements on electric installations in theory and practice.

How to perform line impedance measurement

Step 1 Select the LINE function with function selector switch. The following menu is
displayed:

Figure 5.30: Line impedance measurement menu

Step 2 Set the following measuring parameters:

 Fuse type,
 Fuse current rating,
 Fuse trip-out time,
 Impedance scaling factor (see chapter 4.5.2 Impedance scaling factor
adjustment).

The complete list of available fuse types can be found in Appendix A.

Step 3 Connect the appropriate test leads to the instrument and follow the
connection diagram shown in figure 5.31 to perform phase-neutral or phase-
phase line impedance measurement. Use the Help function if necessary.

45
MI 3002 & MI3102 Measurements

L1
L2
L3
N
PE

N/L2

PE/L3
L/L1
L/L
PE/L3 1
N/L2
N PE L

Ro RE

Figure 5.31: Phase-neutral or phase-phase line impedance measurement

Step 4 Check for warnings displayed on the screen and check the online
voltage/terminal monitor before starting the measurement. If everything is ok,
press the TEST key. After performing the measurement, the results will
appear on the display together with the PASS/FAIL indication (if applicable).

Figure 5.32: Example of line impedance measurement results

Displayed results:
Z .............Line impedance,
I SC ...........Prospective short-circuit current,
Lim .........High limit fault loop impedance value (if applicable).

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 The fault loop impedance limit depends on fuse type, fuse current rating, fuse
trip-out time and Impedance scaling factor.
 The specified accuracy of the test parameter is valid only if mains voltage is
stable during the measurement.

46
MI 3002 & MI3102 Measurements

5.6 Phase sequence testing

In practice, we often deal with the connection of three-phase loads (motors and other
electro-mechanical machines) to three-phase mains installation. Some loads
(ventilators, conveyors, motors, electro-mechanical machines, etc.) require a specific
phase rotation and some may even be damaged if the rotation is reversed. This is why it
is advisable to test phase rotation before connection is made.

For information concerning phase sequence testing refer to Metrel’s handbook

Measurements on electric installations in theory and practice.

How to test the phase sequence

Step 1 Select the PHASE ROTATION function ( ) with the function selector switch.
The following menu is displayed.

Figure 5.33: Phase rotation test menu

Step 2 Connect test cable to the Eurotest instrument and follow the connection
diagram shown in figure 5.34 to test phase sequence.

L3
L2
L1
N
PE
PE/L3

PE/L3
N/L2

N/L2
L/L1

L/L1

option A 1110
result 1.2.3 result 2.1.3

Figure 5.34: Connection of universal test cable and optional three phase cable

Step 3 Check for warnings on the display and check the online voltage/terminal
monitor. The phase sequence test is a continuously running test hence the
results will be displayed as soon as the full test lead connection to the item
under test has been made.. All three-phase voltages are displayed in order of
their sequence represented by the numbers 1, 2 and 3.

47
MI 3002 & MI3102 Measurements

Figure 5.35: Example of phase sequence test result

Displayed results:
Ph ...........Phase sequence,
1.2.3........Correct connection,
2.3.1........Invalid connection,
-.-.- ..........Irregular voltages.
Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

5.7 Voltage and frequency

Voltage measurements should be carried out regularly while dealing with electric
installations (carrying out different measurements and tests, looking for fault locations,
etc.). Frequency is measured for example when establishing the source of mains
voltage (power transformer or individual generator).

How to perform voltage and frequency measurement

Step 1 Select the VOLTAGE function (Volt.) with the function selector switch. The
following menu is displayed:

Figure 5.36: Voltage and frequency measurement menu

Step 2 Connect test cable to the Eurotest instrument and follow the
connection diagram shown in figure 5.37 to perform a voltage and frequency
measurement.

L1
L2
L3
N
PE
N/L2

PE/L3
L/L1

L/L
PE/L3 1
N/L2
N PE L

Ro RE

Figure 5.37: Connection diagram

48
MI 3002 & MI3102 Measurements

Step 3 Check the displayed warnings. The Voltage and Frequency test continually
runs, showing fluctuantions as they occur, these results are shown on the
display during measurement.

Figure 5.38: Examples of voltage and frequency measurements

Displayed results:
Ul-n.........Voltage between phase and neutral conductors,
Ul-pe.......Voltage between phase and protective conductors,
Un-pe .....Voltage between neutral and protective conductors.

When testing three-phase system the following results are displayed:

U1-2........Voltage between phases L1 and L2,
U1-3........Voltage between phases L1 and L3,
U2-3........Voltage between phases L2 and L3.

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

49
MI 3002 & MI3102 Measurements

5.8 Resistance to earth (MI 3102 only)

The MI3102 EurotestXE can perform a 3-wire resistance to earth measurements. This
function is useful for testing the quality of the earthing electrode in TT and IT systems

Consider the following instructions when performing resistance to earth measurement:

 The probe (S) is positioned between the earth electrode (E) and auxiliary earth
electrode (H) in the ground reference plane (see figure 5.40).
 The distance from the earth electrode (E) to the auxiliary earth electrode (H)
should be at least 5 times the depth of earthing electrode rod or the length of the
band electrode.
 If measuring the total earth resistance of a complex earthing system, the required
distance depends on the longest diagonal distance between the individual
earthing electrodes.

For additional information concerning resistance to earth measurement refer to

METREL’s handbook Measurements on electric installations in theory and practice.

How to perform resistance to earth measurement

Step 1 Select the EARTH function with function selector switch. The following menu
is displayed:

Figure 5.39: Earth resistance measurement menu

Step 2 Set the following measuring parameter:

 High limit resistance value.

Step 3 Connect the leads to the instrument and follow the connection diagram shown
in figure 5.40 to perform a resistance to earth measurement. Use the Help
function if necessary.

Test connector terminals are used as follows:

 N/L2 blue test lead is used for the earth electrode (E).
 L/L1 black test lead is used for the auxiliary earth electrode (H).
 PE/L3 green test lead is used for the probe (S).

50
MI 3002 & MI3102 Measurements

E
H S
MPEC

Rc Rp RE

>5d d

Figure 5.40: Connection of standard 20 m long test leads

Step 4 Check for warnings on the display and check the online voltage/terminal
monitor before starting the measurement. If everything is ok, press the TEST
key. After performing the measurement, the results will appear on the display
together with the PASS/FAIL indication (if applicable).

Figure 5.41: Example of resistance to earth measurement results

Displayed results:
R .............resistance to earth,
R C ...........auxiliary earth electrode resistance,
R P ...........probe resistance.

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 If a voltage higher than 30 V is present between the test terminals, the test will be
prevented from being performed.
 If a noise voltage higher than approx. 5 V is present between the H and E or S test
terminals, the (noise) warning symbol “ ” will be displayed, indicating that the
test result may not be correct!

51
MI 3002 & MI3102 Measurements

5.9 TRMS current (MI 3102 only)

This function enables measuring of AC currents in a wide range from 0.5 mA to 20 A
using sensitive current clamp (A 1018) supplied by METREL.

For additional information concerning TRMS current measurement refer to the

METREL’s handbook Measurements on electric installations in theory and practice.

How to perform a TRMS current measurement

Step 1 Select the TRMS CURRENT function (TRMS) with the function selector
switch. The following menu is displayed:

Figure 5.42: TRMS current measurement menu

Step 2 Set the following limit value:

 High limit current value.

Step 3 Connect the test leads to the Eurotest instrument and follow the connection
diagram shown in Figure 5.43 to perform a TRMS current measurement. Use
the Help function if necessary.

L1
L2
L3
N
PE

IL
Option A 1018
I

c c

Figure 5.43: Connection diagram

52
MI 3002 & MI3102 Measurements

Step 4 Check for any warnings on the display before starting the measurement. If
everything is ok, press the TEST key.
After starting the test, the test will run continuously until the user stops the
measurement. To stop measurement, press the TEST key again. The last
measured result will be displayed together with the PASS/FAIL indication (if
applicable).

Figure 5.44: Example of TRMS current measurement result

Displayed results:
I ..............TRMS current (or TRMS leakage current).

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 Use test clamp supplied by METREL or another clamp with similar characteristics
(current output, 1000:1 clamp ratio, appropriate measuring range, consider the
error of the test clamp when evaluating the measured results)!
 Current clamps Metrel A 1074 and A 1019 are suitable for use with MI 3102
EurotestXE instrument in range 0.2 A  200 A. Below 0.2 A they can be used as
indicator only. They are not suitable for leakage current measurements.

53
MI 3002 & MI3102 Measurements

5.10 Illumination (MI 3102 only)

The illumination measurements should be performed whenever planning or installing
indoor or outdoor lighting.
Illumination measurement can be performed using a LUXmeter probe connected to the
RS232 connector of the instrument. The EurotestXE instrument supports type B
LUXmeter and type C LUXmeter probes.

How to perform illumination measurement

Step 1 Select the SENSOR function with the function selector switch. The following
menu is displayed:

Figure 5.45: Illumination measurement menu

Step 2 Set the following limit value:

 Low limit illumination value.

Step 3 Connect LUXmeter probe to the instrument RS232 connector and follow the
positioning diagram shown in figure 5.46 to perform illumination
measurement. Turn on the LUXmeter probe by pressing its ON/OFF key. (the
Green LED should light on the probe). Use the Help function if necessary.

Figure 5.46: LUXmeter probe positioning

54
MI 3002 & MI3102 Measurements

Step 4 Check for any warnings on the display before starting the measurement. If
everything is ok, press the TEST key to start the measurement. The results
will appear on the display along with a PASS/FAIL indication (if applicable).
After starting the test, the test will run continuously until the user stops the
measurement. To stop measurement, press the TEST key again The last
measured result will be displayed, together with the PASS/FAIL indication (if
applicable).

Figure 5.47: Example of illumination measurement result

Displayed result:
E .............Illumination

Refer to chapter 6.1. Saving results for information on how to save the
displayed results for documentation purposes.

Notes:
 For accurate measurements, make sure that the milk glass bulb is lit without any
shadows cast by hand, body or any other unwanted objects.
 It is very important to know when the artificial light sources will reach full power (this
may take a period of time see technical data for light sources for more information)
and should therefore be switched on for this period of time before any
measurements are taken.

55
MI 3002 & MI3102 Measurements

5.11 Testing the PE terminal

In new or adapted installations it may occur that the position of the PE conductor and
the phase conductor become reversed – this is a very dangerous situation! This is why
it is important to test for the presence of a phase voltage on the PE protection terminal.
This test should be performed before a mains supply voltage is applied to the
instrument circuitry and before installation is used.

For additional information concerning PE terminal test, refer to Metrel’s handbook

Measurements on electric installations in theory and practice.

How to test PE terminal

Step 1 Connect test cable to the instrument.

Step 2 Follow the connection diagrams shown in figures 5.48 and 5.49 to test PE
terminal.

L1
N
PE

Reversed phase and

protection conductors!
MOST DANGEROUS
SITUATION!

Figure 5.48: Connection of plug cable to mains outlet with reversed L and PE
conductors

56
MI 3002 & MI3102 Measurements

L1
N
PE
Reversed phase and
protection conductors!
L/
PE/L3 L1 MOST DANGEROUS
N/L2 SITUATION!
N PE L

Figure 5.49: Connection of universal test cable to load connection terminals with
reversed L and PE conductors

Step 3 Touch the PE test probe (TEST key) for a few seconds. If PE terminal is
connected to phase voltage a warning message will be displayed and
instrument buzzer will sound.

Warning:
 If phase voltage is detected on tested PE terminal, stop all measurements
immediately and remove the cause of the fault before proceeding with any
activity!

Notes:
 The PE terminal can only be tested with the function selector set to RCD, LOOP
or LINE!
 For correct testing of PE terminals, the TEST key has to be touched for a few
seconds.
 When testing, make sure the instrument operated is stood on non-isolated floor
(otherwise the test result may be wrong!)

57
MI 3002 & MI3102 Working with results

6 Working with results

After a measurement is completed, the results can be stored into the memory of the
instrument, together with any sub-results and function parameters.
Electrical installations can be represented by a multi-level structure. The instrument’s
memory storage is designed in a three-level structure as follows:
 Object (1st structure level),
 Distribution Board (2nd structure level),
 Circuit, Earth Electrode, Bonding conductors (3rd structure level).
OBJECT 001
 DISTRIBUTION BOARD 001
 CIRCUIT 001
 CIRCUIT 002
...
 CIRCUIT 499

 EARTH ELECTRODE

 BONDING Water
 BONDING Oil
 BONDING Lightning
 BONDING Gas
 BONDING Structural Steel
 BONDING Other
 BONDING Earthing conductor

 DISTRIBUTION BOARD 002

 CIRCUIT 001
 CIRCUIT 002
...
 CIRCUIT 499

 EARTH ELECTRODE

 BONDING Water
 BONDING Oil
 BONDING Lightning
 BONDING Gas
 BONDING Structural Steel
 BONDING Other
 BONDING Earthing conductor

 DISTRIBUTION BOARD 999

 CIRCUIT 001
 CIRCUIT 002
...
 CIRCUIT 499

 EARTH ELECTRODE

 BONDING Water
 BONDING Oil
 BONDING Lightning
 BONDING Gas
 BONDING Structural Steel
 BONDING Other
 BONDING Earthing conductor
OBJECT 002
...

OBJECT 999

Figure 6.1: Instrument memory organization

The memory structure is organized in a way that is suited to the BS 7671 and other
verification documents (Electrical Installation Certificate, Periodic Inspection Report

58
MI 3002 & MI3102 Working with results

etc.). If the results are stored in appropriate memory locations the automatic creation of
a certificate/ report is possible via the PC software.

6.1 Saving results

How to save measurement results

Step 1 When the measurement has completed, press the MEM key. The SAVE
results menu is displayed with the last used memory location selected.

Figure 6.2: Examples of Save results menu

Step 2 The results can be saved into the selected memory location as follows:
By using the / keys, position the cursor on the Object line. Use the /
keys to select appropriate ‘Object’ memory location (three-digit number ).
By using the / keys, position the cursor on the D. Board line. Use the /
keys to select appropriate ‘Distribution block’ memory location (three-digit
number).
By using the / keys, position the cursor on the Circuit / Earth Electr. /
Bonding line.
Choose between the various options (‘Circuit’, ‘Earth Electrode’ or ‘Bonding’)
by pressing the TEST key.
If Circuit is selected, use the / keys to select the appropriate ‘Circuit’
memory location (three-digit number).
If Bonding is selected, use the / keys to select the appropriate ‘Bonding’
memory location (Water/ Oil/ Lightning/ Gas/ Str.steel/ Earth.cond).

Step 3 After the memory location is set, press the MEM key to save the results.
»Saved to memory« message will displayed to confirm that the results have
been saved. After saving the results the instrument returns to normal test
screen.

Note:
 Each measurement result can be saved only once.

59
 MI 3002 & MI3102 Working with results

6.2 Recalling results

Stored results can be recalled from the memory in the Memory menu.. To enter the
Memory menu press the MEM key.

Figure 6.3: Memory menu

How to recall saved results

Step 1 Select Recall results from the Memory menu by using the  and  keys and
press the TEST key to confirm. The Recall results menu will be displayed and
the last used memory location will be selected.

Figure 6.4: Examples of menus for selection of memory location

Step 2 To recall a saved result the memory location must be selected first:
The Object line can be selected with the / keys. Use the / keys to
select the appropriate ‘Object ‘memory location (three-digit number).
In the lower part of the display, two numbers will be displayed (e.g. No.:2/16
see figure 6.4):
- the first number is the number of measurements stored in the selected
‘Object’ memory location.
- the second number is the number of measurements stored in the selected
‘Object’ memory location and its sub-locations (i.e. D.board, Circuit, Earth
Electrode, Bonding memory locations).

The D. Board line can be selected with the / keys. Use the / keys to
select appropriate ‘D. Board memory location (three-digit number).
In the lower part of the display, two numbers will be displayed (e.g. 6/16 see
figure 6.4):
- the first number is the number of measurements stored in the selected ‘D.
Board’ memory location.
- the second number is the number of measurements stored in the selected
‘D. Board’ memory location and its sub-locations (Circuit, Electrode,
Bonding memory locations).

60
MI 3002 & MI3102 Working with results

The Circuit / Earth Electrode / Bonding line can be selected with the /
keys.
The appropriate memory location (‘Circuit’ or ‘Earth Electrode’or ‘Bonding’)
can be selected with the TEST key.
If the Circuit is selected, use the / keys to select the appropriate ‘Circuit’
memory location.(three-digit number). In the lower part of the display (No.
line) the number of measurements stored in the selected ‘Circuit’ memory
location is shown.
If the Bonding is selected, use the / keys to select appropriate ‘Bonding’
memory location (e.g. Water/ Oil/ Lightning/ Gas/ Str.Steel/ Earth.cond.). In
the lower part of the display the number of measurements stored in the
selected ‘Bonding’ memory location is shown.
If the Earth Electrode is selected, the number of measurements stored in the
selected ‘Electrode’ memory location will be displayed in the lower part of the
display.

Step 3 Once the memory location is set, press the MEM key and the cursor will jump
down to the No. line

Figure 6.5: Menu for selection of measurements

Use the / keys to select the function for which you want to view results and
press the TEST key to confirm.

Figure 6.6: Examples of recalled results menu

Under the same memory location the other saved results can be viewed by
using the / keys,
Pressing the MEM key returns the instrument back to the Memory Menu in
order selection of an alternative memory location..

To exit the Recall results menu, rotate the function switch.

61
MI 3002 & MI3102 Working with results

6.3 Deleting results

When deleting results the following actions can be taken:
 Individual results can be deleted,
 Results in a memory location and its sub-locations can be deleted
 All saved results can be deleted.
The stored results can be deleted from the memory from the Memory menu.
To enter the Memory menu, press the MEM key.

Figure 6.7: Memory menu

How to select result(s) to be deleted

Step 1 Select Delete results from the Memory menu by using the  and  keys to
place the cursor next to the option and press the TEST key to confirm. The
Delete results menu will be displayed and the last used memory location will
be selected

Figure 6.8: Examples of menus for selection of memory location

Step 2 To delete saved result(s) the memory location must be selected first:
The Object line can be selected with the / keys. Use the / keys to
select the appropriate ‘Object ‘memory location (three-digit number).
In the lower part of the display, two numbers will be displayed (e.g. No.:2/16
see figure 6.8):
- the first number is the number of measurements stored in the selected
‘Object’ memory location.
- the second number is the number of measurements stored in the selected
‘Object’ memory location and its sub-locations (i.e. D.board, Circuit, Earth
Electrode, Bonding memory locations).

The D. Board line can be selected with the / keys. Use the / keys to
select appropriate ‘D. Board memory location (three-digit number).
In the lower part of the display, two numbers will be displayed (e.g. 6/16 see
figure 6.8):
- the first number is the number of measurements stored in the selected ‘D.
Board’ memory location.

62
MI 3002 & MI3102 Working with results

- the second number is the number of measurements stored in the selected

‘D. Board’ memory location and its sub-locations (Circuit, Electrode,
Bonding memory locations).

The Circuit / Earth Electrode / Bonding line can be selected with the /
keys.
The appropriate memory location (‘Circuit’ or ‘Earth Electrode’or ‘Bonding’)
can be selected with the TEST key.
If the Circuit is selected, use the / keys to select the appropriate ‘Circuit’
memory location.(three-digit number). In the lower part of the display (No.
line) the number of measurements stored in the selected ‘Circuit’ memory
location is shown.
If the Bonding is selected, use the / keys to select appropriate ‘Bonding’
memory location (e.g. Water/ Oil/ Lightning/ Gas/ Str.Steel/ Earth.cond.). In
the lower part of the display the number of measurements stored in the
selected ‘Bonding’ memory location is shown.
If the Earth Electrode is selected, the number of measurements stored in the
selected ‘Electrode’ memory location will be displayed in the lower part of the
display.

To exit the Delete results menu without deleting any results, rotate the function switch.

How to delete individual saved results

Step 1 After the memory location (Object, D. Board, Electrode, Bonding, Circuit) has
been selected, press the MEM key. The cursor will jump down to the No. line

Figure 6.8: Menus for deleting individual results

Step 2 Use the / keys to select the results you want to delete and press the TEST
key. Press the TEST key again to confirm that the results require deletion or
press MEM key to return to the menu for the selection of different memory
location (without deleting any results).

63
MI 3002 & MI3102 Working with results

How to delete all saved results in a memory location and its sub-
locations

Step 1 After the memory location (Object, D. Board, Earth Electrode, Bonding,
Circuit) has been selected, press the HELP key. A warning will appear at the
bottom of the screen asking for confirmation.

Figure 6.9: Menus for deleting all results in memory location and its subitems

Step 2 Press the TEST key to delete the results in the selected memory location and
all of the associated sub-locations. Press the TEST key again for confirmation
or press MEM key to return to the menu for selection of memory location
without changes.

How to delete all saved results

Step 1 Select Clear memory in Memory menu by using the  and  keys and press
the TEST key to confirm. The following menu is displayed:

Figure 6.9: Clear memory menu

Step 2 Press the TEST key again to confirm that all results require deleting or press
any cursor key (or MEM key) to return to the Memory menu without deleting
any saved results.

64
MI 3002 & MI3102 RS232 / USB communication

7 RS232 / USB communication

The MI3102 EurotestXE and MI3002 Eurotest DL include both RS232 and USB
communication ports. These ports can be used to send stored results through to a PC
for reviewing, editing and report building.

PS/2 - RS 232 cable

minimum connections: 1 to 2, 4 to 3, 3 to 5

3 1
5
1
2 6
4

PS/2 for MI 3101 9 pin D female for PC

Figure 7.1: Interface connection for data transfer over PC COM port

7.1 EuroLinkPRO PC software

The EuroLinkPRO software allows the following activities:
 Data downloading,
 Creation of Verification documents,
 Export of measured data to a spreadsheet.

The EuroLinkPRO is a PC software running on Windows 2000 and Windows XP and

Windows Vista operating systems.

How to download saved results to the PC

Step 1 Connect the Eurotest instrument to PC using either the RS232 or USB cable.
Make sure that the correct communication port is selected and that the Eurotest
instrument is switched on. Refer to chapter 4.5.4 Communication port selection.

Step 2 Run EuroLinkPRO software on the PC.

Step 3 Select the Receive results icon or Instrument / Receive results option from
the menu. The system will begin to download results saved in the instruments
memory onto the PC. After the result have been downloaded, the following
memory structure will be displayed.

65
MI 3002 & MI3102 RS232 / USB communication

Figure 7.2: Example of downloaded results

Step 4 The software allows a variety of tasks to be performed including editting the
downloaded structure for documentation purposes, saving results / parameters
to an *.eul file or proceed to creation of appropriate Report / Certificate.

Note:
 The USB drivers must be installed on PC before using the USB interface is used.
See accompanying CD for further instructions about USB installation.
 For more information about the operation of the software application, please see
the help files available from the HELP option in the EurolinkPRO software.

66
MI 3002 & MI3102 Maintenance

8 Maintenance
8.1 Replacing fuses
There are three fuses under back battery cover of the Eurotest instrument.
 F1
M 0.315 A / 250 V, 205 mm
This fuse protects internal circuitry of low-value resistance function if test probes
are connected to the mains supply voltage by mistake.
 F2, F3
F 4 A / 500 V, 326.3 mm
General input protection fuses for the L/L1 and N/L2 test terminals.

Warnings:

 Disconnect any measuring accessory from the instrument and ensure that
the instrument is turned off before opening the battery/fuse compartment cover,
hazardous voltage can exist inside this compartment!
 Replace any blown fuses with exactly the same type of fuse. The instrument can
be damaged and/or operator’s safety impaired if this is not performed!
The Position of fuses can be seen in figure 3.4 in chapter 3.3 Back panel.

8.2 Cleaning
No special maintenance is required for the housing. To clean the surface of the
instrument use a soft cloth slightly moistened with soapy water or alcohol. Then leave
the instrument to dry totally before use.

Warnings:
 Do not use liquids based on petrol or hydrocarbons!
 Do not spill cleaning liquid over the instrument!

8.3 Periodic calibration

It is essential that the test instrument is regularly calibrated in order for the technical
specification listed in this manual to be guaranteed. We recommend an annual
calibration. The calibration should be done by an authorised technical person only.
Please contact your dealer for further information.

8.4 Service
For repairs under warranty, or at any other time, please contact your distributor.
Unauthorised person(s) are not allowed to open the Eurotest instrument. There are no
user replaceable components inside the instrument, except for the three fuses inside
the battery compartment, refer to chapter 8.1 Replacing fuses.

67
MI 3002 & MI3102 Technical specifications

9 Technical specifications
9.1 Insulation resistance
Insulation resistance (nominal voltages 100 V DC and 250 V DC )
Measuring range according to EN61557-2 is 0.017 M  199.9 M.
Measuring range (M) Resolution (M) Accuracy
0.000  1.999 0.001
2.00  99.99 0.01 (5 % of reading + 3 digits)
100.0  199.9 0.1

Insulation resistance (nominal voltages 500 V DC and 1000 V DC )

Measuring range according to EN61557-2 is 0.015 M  999 M.
Measuring range (M) Resolution (M) Accuracy
0.000  1.999 0.001
2.00  99.99 0.01 (2 % of reading + 3 digits)
100.0  199.9 0.1
200  999 1 (10 % of reading)

Voltage
Measuring range (V) Resolution (V) Accuracy
0  1200 1 (3 % of reading + 3 digits)

Nominal voltages .............................. 100 V DC , 250 V DC , 500 V DC , 1000 V DC

Open circuit voltage .......................... -0 % / +20 % of nominal voltage
Measuring current............................. min. 1 mA at R N =U N 1 k/V
Short circuit current........................... max. 3 mA
Specified accuracy is valid if universal test cable is used, while it is valid up to 200 M if
tip commander is used.
The number of possible tests
with a new set of batteries ................ up to 1800
Auto discharge after test.
In case the instrument gets moistened the results could be impaired. In such case it is
recommended to dry the instrument and accessories for at least 24 hours.

9.2 Continuity resistance

Measuring range according to EN61557-4 is 0.16   1999 .
Measuring range () Resolution () Accuracy
0.00  19.99 0.01 (3 % of reading + 3 digits)
20.0  99.9 0.1
(5 % of reading)
100  1999 1

Open-circuit voltage.......................... 6.5 V DC  9 V DC

Measuring current............................. min. 200 mA into load resistance of 2 
Test lead compensation.................... up to 5 

68
MI 3002 & MI3102 Technical specifications

The number of possible tests

with a new set of batteries ................ up to 5500
Automatic polarity reversal of the test voltage.

9.3 RCD testing

9.3.1 General data
Nominal residual current................... 10 mA, 30 mA, 100 mA, 300 mA, 500 mA,
1000 mA
Nominal residual current accuracy.... -0 / +0.1I  ; I  = I N , 2I N , 5I N
-0.1I  / +0; I  = ½I N
Test current shape............................ Sine-wave (AC), pulsed (A)
RCD type .......................................... general (G, non-delayed), selective (S, time-
delayed)
Test current starting polarity ............. 0 or 1800
0

Voltage range ................................... 100 V  264 V (45 Hz  65 Hz)

RCD test current selection (r.m.s. value calculated to 20 ms) according to IEC 61009:
½I N 1I N 2I N 5I N RCD I
I N (mA) AC A AC A AC A AC A AC A
10 5 3,5 10 20 20 40 50 100  
30 15 10,5 30 42 60 84 150 212  
100 50 35 100 141 200 282 500 707  
*)
300 150 105 300 424 600 848 1500  
*)
500 250 175 500 707 1000 1410 2500  
*) *) *)
1000 500 350 1000 1410 2000  
*)
not available

9.3.2 Contact voltage

Measuring range according to EN61557-6 is 3.0 V  49.0 V for limit contact voltage 25
V.
Measuring range according to EN61557-6 is 3.0 V  99.0 V for limit contact voltage 50
V.
Measuring range (V) Resolution (V) Accuracy
0.0  9.9 0.1
(-0 % / +10 %) of reading + 2
digits
10.0  99.9 0.1 (-0 % / +10 %) of reading
Accuracy applies for 1 year in reference conditions. Temperature coeficient ouside
these limits is +1 digit.
Test current ...................................... max. 0.5I N
Limit contact voltage ......................... 25 V, 50 V
UC
Fault loop resistance at contact voltage is calculated as RL  .
I N

69
MI 3002 & MI3102 Technical specifications

9.3.3 Trip-out time

Complete measurement range corresponds to EN61557-6 requirements. Specified
accuracies are valid for complete operating range.

General (non-delayed) RCDs

Measuring range (ms) Resolution (ms) Accuracy
0  300 (½I N , I N ) 1
0  150 (2I N ) 1 3 ms
0  40 (5I N ) 1

Selective (time-delayed) RCDs

Measuring range (ms) Resolution (ms) Accuracy
0  500 (½I N , I N ) 1
0  200 (2I N ) 1 3 ms
0  150 (5I N ) 1

Test current ...................................... ½I N , I N , 2I N , 5I N

Multiplier 5 is not available if I N =1000 mA (AC type RCDs) or I N  300 mA (A type
RCDs).
Multiplier 2 is not available if I N =1000 mA (A type RCDs).

9.3.4 Trip-out current

Trip-out current (I N =10 mA)

Measurement range corresponds to EN61557-6 requirements. Specified accuracies are
valid for complete operating range.
Measuring range I  Resolution I  Accuracy
0.2I N  1.1I N (AC type) 0.05I N 0.1I N
0.2I N  2.2I N (A type) 0.05I N 0.1I N
Trip-out current (I N 30 mA)
Measurement range corresponds to EN61557-6 requirements. Specified accuracies are
valid for complete operating range.

Measuring range I  Resolution I  Accuracy

0.2I N  1.1I N (AC type) 0.05I N 0.1I N
0.2I N  1.5I N (A type) 0.05I N 0.1I N

Trip-out time
Measuring range (ms) Resolution (ms) Accuracy
0  300 1 3 ms

Contact voltage
Measuring range (V) Resolution (V) Accuracy
(-0 % / +10 %) of reading +
0.0  9.9 0.1
2 digits
10.0  99.9 0.1 (-0 % / +10 %) of reading

70
MI 3002 & MI3102 Technical specifications

9.4 Fault loop impedance and prospective fault current

Zs sub-function
Measuring range according to EN61557-3 is 0.25   1999 .
Measuring range () Resolution () Accuracy
0.00  19.99 0.01
20.0  99.9 0.1 (5 % of reading + 5 digits)
100  1999 1

Prospective fault current (calculated value)

Measuring range (A) Resolution (A) Accuracy

0.00  19.99 0.01
20.0  99.9 0.1 Consider accuracy of fault
100  999 1 loop resistance
1.00k  9.99k 10 measurement
10.0  24.4k 100

Test current (at 230 V)...................... 7.5 A (10 ms  t LOAD  15 ms)

Nominal voltage range...................... 100 V  264 V (45 Hz  65 Hz)

Zs(rcd) trip-lock sub-function

Measuring range according to EN61557 is 0.46   1999 .
Measuring range () Resolution () Accuracy *)
0.00  19.99 0.01 (5 % of reading + 10 digits)
20.0  99.9 0.1  10 % of reading
100  1999 1  10 % of reading
*)
Acccuracy may be impaired in case of heavy noise on mains voltage.

Prospective fault current (calculated value)

Measuring range (A) Resolution (A) Accuracy
0.00  19.99 0.01
20.0  99.9 0.1 Consider accuracy of fault
100  999 1 loop resistance
1.00k  9.99k 10 measurement
10.0  24.4k 100
No trip out of RCD.

9.5 Line impedance and prospective short-circuit current

Line impedance
Measuring range according to EN61557-3 is 0.25   1999 .
Measuring range () Resolution () Accuracy
0.00  19.99 0.01
20.0  99.9 0.1 (5 % of reading + 5 digits)
100  1999 1

71
MI 3002 & MI3102 Technical specifications

Prospective short-circuit current (calculated value)

Measuring range (A) Resolution (A) Accuracy
0.00  19.99 0.01
20.0  99.9 0.1
Consider accuracy of line
100  999 1
resistance measurement
1.00k  9.99k 10
10.0  24.4k 100

Test current (at 230 V)...................... 7.5 A (10 ms  t LOAD  15 ms)

Nominal voltage range 100 V  440 V (45 Hz  65 Hz)

9.6 Resistance to earth (MI 3102 only)

Measuring range according to EN61557-5 is 0.15   1999 .
Measuring range () Resolution () Accuracy
0.00  19.99 0.01
20.0  99.9 0.1 (2 % of reading + 3 digits)
100  1999 1

Max. auxiliary earth electrode

resistance R C ............................................ 100R E or 50 k (whichever is lower)
Max. probe resistance R P ......................... 100R E or 50 k (whichever is lower)
Additional probe resistance error
at R Cmax or R Pmax. ...................................... (10 % of reading + 10 digits)
Additional error
at 3 V voltage noise (50 Hz) ..................... (5 % of reading + 10 digits)
Open circuit voltage .................................. < 45 V AC
Short circuit voltage .................................. < 20 mA
Test voltage frequency ............................. 125 Hz
Test voltage shape ................................... rectangular
Noise voltage indication threshold ............ 1 V (< 50 , worst case)
Automatic measurement of auxiliary electrode resistance and probe resistance.
Automatic measurement of voltage noise.

9.7 TRMS current (MI 3102 only)

TRMS current or TRMS leakage current
Measuring range (A) Resolution (A) Accuracy
0.0  99.9 mA 0.1 mA (5 % of reading + 3 digits)
100  999 mA 1 mA
(5 % of reading)
1.00  19.99 A 0.01 A

Input resistance .........................................100 

Maximal continuous input current ............. 30 mA (=30 A @ current clamp with ratio
1000:1)

72
MI 3002 & MI3102 Technical specifications

Measurement principle ..............................current clamp, ratio 1000:1

Nominal frequency.....................................45 Hz  65 Hz
Additional clamp error has to be considered.

9.8 Illumination (MI 3102 only)

9.8.1 Illumination (LUXmeter type B)
Specified accuracy is valid for complete operating range.
Measuring range (lux) Resolution (lux) Accuracy
0.01  19.99 0.01 (5 % of reading + 2 digits)
0.1  199.9 0.1
200  1999 1 (5 % of reading)
2.00  19.99 k 10
Measurement principle ............................. silicon photodiode with V() filter
Spectral response error ............................ < 3.8 % according to CIE curve
Cosine error .............................................. < 2.5 % up to an incident angle of  85O
Overall accuracy ....................................... matched to DIN 5032 class B standard

9.8.2 Illumination (LUXmeter type C)

Specified accuracy is valid for complete operating range.
Measuring range (lux) Resolution (lux) Accuracy
(10 % of reading +
0.01  19.99 0.01
3 digits)
0.1  199.9 0.1
200  1999 1 (10 % of reading)
2.00  19.99 k 10
Measurement principle ............................. silicon photodiode
Cosine error .............................................. < 2.5 % up to an incident angle of  85O
Overall accuracy ....................................... matched to DIN 5032 class C standard

9.9 Phase rotation

Nominal mains voltage range ........... 100 V AC  440 V AC
Nominal frequency range.................. 45 Hz  65 Hz
Result displayed ............................... 1.2.3 or 2.1.3

9.10 Voltage and frequency

Measuring range (V) Resolution (V) Accuracy
0  500 1 (2 % of reading + 2 digits)

Nominal frequency range.................. 0 Hz, 45 Hz  65 Hz

73
MI 3002 & MI3102 Technical specifications

Measuring range (Hz) Resolution (Hz) Accuracy

45.0  65.0 0.1  2 digits

Nominal voltage range...................... 10 V  500 V

9.11 Online voltage monitor

Measuring range (V) Resolution (V) Accuracy
0  500 1 (2 % of reading + 2 digits)

Nominal frequency range.................. 0 Hz, 45 Hz  65 Hz

If voltage greater than 500 V is applied to the test terminals, online voltage monitor is
used as voltage indicator only.

9.12 General data

Power supply voltage........................ 9 V DC (61.5 V battery cells, size AA)
Power supply adapter ....................... 12 V  15 V / 400 mA
Battery charging current ................... < 250 mA (internally regulated)
Operation.......................................... typical 15 h

Overvoltage category........................ CAT III / 600 V; CAT IV / 300 V

Plug commander (optional)
overvoltage category ........................ CAT III / 300 V

Protection classification .................... double insulation

Pollution degree................................ 2
Protection degree ............................. IP 42

Display ............................................ 12864 dots matrix display with backlight

Dimensions (w  h  d) ..................... 23 cm  10.3 cm  11.5 cm

Weight (without battery).................... 1.31 kg

Reference conditions
Reference temperature range ........ 10 OC  30 OC
Reference humidity range .............. 40 %RH  70 %RH

Operating conditions
Working temperature range ........... 0 OC  40 OC
Maximum relative humidity............. 95 %RH (0 OC  40 OC), non-condensing

Storage conditions
Temperature range ........................ -10 OC  +70 OC

74
MI 3002 & MI3102 Technical specifications

Maximum relative humidity............. 90 %RH (-10 OC  +40 OC)

80 %RH (40 OC  60 OC)

The error in operating conditions could be at most the error for reference conditions
(specified in the manual for each function) + 1 % of measured value + 1 digit unless
otherwise specified.

75
MI 3002 & MI3102 Fuse base tables

A Fuse base tables

Fuse type B Fuse type C
Rated Disconnection time [s] Rated Disconnection time [s]
current 0.4 5 current 0.4 5
(A) Max. loop impedance () (A) Max. loop impedance ()
3 12,264 12,264
6 6,136 6,136 6 3,064 3,064
10 3,68 3,68 10 1,84 1,84
16 2,296 2,296 16 1,152 1,152
20 1,84 1,84 20 0,92 0,92
25 1,472 1,472 25 0,736 0,736
32 1,152 1,152 32 0,576 0,576
40 0,92 0,92 40 0,456 0,456
50 0,736 0,736 50 0,368 0,368
63 0,584 0,584 63 0,288 0,288
80 0,456 0,456 80 0,232 0,232
100 0,368 0,368 100 0,184 0,184
125 0,296 0,296 125 0,144 0,144
Fuse type D Fuse type BS 88-3 (system C)
Rated Disconnection time [s] Rated Disconnection time [s]
current 0.4 5 current 0.4 5
(A) Max. loop impedance () (A) Max. loop impedance ()
6 1,536 1,536 5 8,36 12,264
10 0,92 0,92 16 1,936 3,288
16 0,576 0,576 20 1,632 2,704
20 0,456 0,456 32 0,768 1,312
25 0,368 0,368 45 0,832
32 0,288 0,288 63 0,576
40 0,232 0,232 80 0,424
50 0,184 0,184 100 0,32
63 0,144 0,144
80 0,112 0,112
100 0,088 0,088
125 0,072 0,072
Fuse type BS 88-2 (systems E and G) Fuse type BS 1362
Rated Disconnection time [s] Rated Disconnection time [s]
current 0.4 5 current 0.4 5
(A) Max. loop impedance () (A) Max. loop impedance ()
6 6,568 10,24 3 13,12 18,56
10 3,912 5,752 13 1,936 3,064
16 2,048 3,344
20 1,416 2,36 Fuse type BS 3036
25 1,08 1,84 Rated Disconnection time [s]
32 0,832 1,472 current 0.4 5
40 1,08 (A) Max. loop impedance ()
50 0,832 5 7,664 14,16
63 0,656 15 2,04 4,28
80 0,456 20 1,416 3,064
100 0,368 30 0,872 2,112
125 0,272 45 1,272
160 0,224 60 0,896
200 0,152 100 0,424
All impedances are scaled with factor 0.8.

76
MI 3002 & MI3102 IT supply systems

B IT supply systems
In order for the operator to be familiar with the measurements and their typical
applications on IT supply systems, it is advisable to read Metrel’s handbook
Measurements on IT power supply systems.

B.1 Standard references

EN 60364-4-41, EN 60364-6, EN 60364-7-710, BS 7671

B.2 Fundamentals
An IT supply system is a mains supply system that is insulated from ground (PE) (i.e. it
is ungrounded supplying system). The system either has no direct connection to ground
or the connection is provided through a relatively high impedance. IT systems mainly
occur in areas where additional protection against electric shock is required. Typical
places are medical surgery rooms.
IT supply systems also has no grounding currents except leakages, and in this way they
are not suceptable to problems with step voltages, (e.g. voltage drops in a step) or high
energy sparking in extrinsic areas.

In normal situations, a high impedance to ground exists and is formed by the

capacitances of the supply wires to ground and the capacitances between the primary
and secondary windings of the IT supply transformer. A minor part of the capacitance is
formed by Y capacitors (EMC) in the mains section of any connected equipment.
Selecting the appropriate transformer, installation cabling and the selection of an
optional high impedance connection to ground can control the maximum leakage
current of the system.
Depending on the application, additional impedances to ground can be applied or can
occur through special loading equipment (as presented in figure B.1). The value of the
impedance should be greater than 100 .

The IT system can provide an additional level of protection against electric shock. In the
situation where a failure occurs in any of the insulation between the line conductors and
PE (e.g. through equipment failure, wrong application or procedure), this system will
remain safe but will be converted into a TN / TT type system. However, additional failure
can be hazardous, which means that the insulation must be continuously checked and
repaired immediately after a failure has been detected.
Supplementary to other protection devices, an IT system normally contains insulation
monitoring devices (IMD) or systems that sound alarms when insulation resistance or
impedance drops below set threshold. The threshold value usually depends on
environment and the application. (e.g. Typical value for a medical installations is 55 k.
In some countries, it is not enough to trace the insulation resistance of the IT supply
system to ground, they require tracing of system capacitance, too.

IEC 60364-4-41 (©IEC): In IT systems, live parts shall be insulated from earth or
connected to earth through sufficiently high impedance. This connection may be made

77
MI 3002 & MI3102 IT supply systems

either at the neutral point or at midpoint of the system or at an artificial neutral point.
The latter may be connected directly to earth if the resulting impedance to earth is
sufficiently high at the system frequency. Where no neutral point or mid-point exists a
line conductor may be connected to earth through high impedance.

L1

133 V
230 V
133 V 230 V
133 V
L2
230 V L3
Optional
high N (Optional) IMD
impedance

Figure B.1: General IT supply system

 Three phase star connection, optional delta connection.

 Optional neutral line.
 Single-phase connection is also possible.
 Various system voltages – not only three phase 230 V as indicated above.
 One faulty connection of any line to PE is treated as first fault and is regular but it
has to be repaired as soon as possible.
 IEC 60364-4-41: In IT systems the following monitoring devices and protective
devices may be used:
- Insulation monitoring devices (IMDs),
- Residual current monitoring devices (RCMs),
- Insulation fault location systems,
- Overcurrent protective devices,
- Residual current protective devices (RCDs).

Note:
 Where a residual current operating device (RCD) is used, tripping of the RCD in
the event of a first fault cannot be excluded due to capacitive leakage currents.

Testing of IT supply system is slightly different to standard tests in TN / TT system.

78
MI 3002 & MI3102 IT supply systems

B.3 Measurement guides

The user has to select the IT supply system in the instrument before testing it. The
procedure for selecting the IT supply system is defined in chapter 4.5.1 Supply system
setup. Once the IT system is selected the instrument can be used immediately. The
instrument keeps selected IT system when it is turned off.

The table below contains functions of the instrument including compatibility notes
related to IT system.

IT system functions Notes

Contunuity functions
RLOW
Independent of selected supply system.
Continuity
Insulation Independent of selected supply system.
Line impedance
Line impedance Impedance Z L1-L2 .
Prospective short circuit I PSC for rated U L1-L2 .
current
Fault loop impedance Independent of selected supply system
Fault loop impedance
Prospective fault current
Voltage, frequency Symbols modified for IT system.
Phase rotation Three-phase system automatic detected.
RCD functions Independent of selected supply system
Contact voltage U C
Trip-out time
Trip-out current Bypassing principle shown in figure B.3.
Automatic test
Earth resistance Independent of selected supply system.
PE test probe Active, but does not inhibit selected test if voltage is
detected.

B.3.1 Voltage

Figure B.2: Example of voltage and frequency measurements

Displayed results for single phase system:

L1-L2 ......Voltage between line conductors,
L1-pe ......Voltage between line 1 and protective conductor,
L2-pe ......Voltage between line 2 and protective conductor.

79
MI 3002 & MI3102 IT supply systems

B.3.2 Line impedance

See chapter 5.5 Line impedance and prospective short-circuit current, the measurement
is the same; only terminal voltage monitor indication corresponds to IT system.

B.3.3 RCD testing

RCD testing is performed in the same way as in TN/TT system (See chapter 5.3 Testing
RCDs), with the following exception:
 Contact voltage measurement is not relevant.

Test circuit with bypassing principle should correspond to that in figure B.3.

Zi
RCD RCD
L1
L2
L3
PE

L/L
1
N/L2
L2 PE L1
PE/L3

RE RE2

Figure B.3: RCD testing in IT system

B.3.4 First fault leakage current (ISFL) (MI 3102 only)

First fault leakage current measurement is performed in order to verify the maximum
current that could leak into PE from observed line. This current flows through the
insulation resistance and reactance (capacitance) between the other lines and PE.

80
MI 3002 & MI3102 IT supply systems

How to perform first fault current measurement

Step 1 Select the Insulation function with the function selector switch and use the
/ keys to select ISFL (first fault current) function. The following menu is
displayed:

Figure B.4: First fault current measurement menu

Step 2 Set the following limit value:

 First fault current high limit value.

Step 3 Connect test cable to the instrument and to the item under test. Follow the
connection diagram shown in figure B.5 to perform first fault current
measurement. Use the Help function if necessary.
L1
L2
L3
PE

L/L
IMD N/L2
PE/L3 1

L2 PE L1

Zi RE

Figure B.5: Connection with plug commander and universal test cable

Step 4 Check the displayed warnings and online voltage/terminal monitor before
starting measurement. If OK, press the TEST key. After performing the
measurement results appear on the display together with the PASS/FAIL
indication (if applicable).

Figure B.6: Example of first fault current measurement results

81
MI 3002 & MI3102 IT supply systems

Displayed results:
I SC1 .........First fault current between L1-PE,
I SC2 .........First fault current between L2-PE.

Save displayed results for documentation purposes. Refer to chapter 6.1.

Saving results.

B.3.5 Insulation monitoring device testing (MI 3102 only)

How to check insulation monitoring device

Step 1 Select the Insulation function with the function selector switch and use the
/ keys to select IMD check function. The following menu is displayed:

Figure B.7: IMD check menu

Step 2 Set the following limit value:

o Fault resistance (indicative)
o Calculated first fault current high limit value.

Step 3 Connect test cable to the instrument and to the item under test. Follow the
connection diagram shown in figure B.5 to check insulation monitor device.
Use the Help function if necessary.

Step 4 Check the displayed warnings and online voltage/terminal monitor before
starting the measurement. If OK, press the TEST key. Use the / keys to
decrease indicative insulation resistance until insulation monitor device
alarms bad insulation. Indicative insulation resistance and calculated first fault
current between first live conductor (e.g. L1) and PE conductor are displayed.
After performing the measurement results with PASS/FAIL indication appear
on the display.

Figure B.8: First fault condition between L1 and PE

Step 5 Use the  key to select second live line (e.g. L2). Use the / keys to
decrease indicative insulation resistance until insulation monitor device

82
MI 3002 & MI3102 IT supply systems

alarms bad insulation. Indicative insulation resistance and calculated first fault
current between second live conductor (e.g. L2) and PE conductor are
displayed.
To complete measurement press the TEST key again.
After performing the measurement results with PASS/FAIL indication appear
on the display.

Figure B.9: First fault condition between L2 and PE

Displayed results:
R1 ...........Threshold indicative insulation resistance for L1,
I1 ............Calculated first fault leakage current at treshold insulation
resistance for L1,
R2 ...........Threshold indicative insulation resistance for L2,
I2 ............Calculated first fault leakage current at treshold indicative insulation
resistance for L2.

First fault leakage currents I 1 and I 2 are calculated as follows:

UL1 L 2 U
I1  , I2  L1 L 2
R1 R2
where:
U L1-L2 ......Measured voltage between L1 and L2,
R 1 ...........Threshold insulation resistance for L1,
R 2 ...........Threshold insulation resistance for L2.

The calculated first fault current is the maximum current that would flow when
insulation resistance decreases to the same value as the applied test
resistance, and a first fault is assumed between opposite line and PE.

Save displayed results for documentation purposes. Refer to chapter 6.1.

Saving results.

Note:
 It is recommended to disconnect all appliances from the tested supply net to
receive regular test results. Any connected appliance will influence the insulation
resistance threshold test.
 The displayed resistances and currents are indicative only. Displayed resistance
can significantly differ from the actual resistance the Eurotest simulates. If IMD’s
with very low test currents (below 1mA) are checked the displayed resistance
value is typically lower (and current higher) than the actual simulated resistance.
The difference is lower for lower set resistances.

83
MI 3002 & MI3102 IT supply systems

B.4 Technical specifications (MI 3102 only)

Only technical specifications that are different to the specifications from chapter 9 of this
document are listed below.

B.4.1 First fault leakage current (ISFL)

Measuring range (mA) Resolution (mA) Accuracy

0.0  9.9 0.1 (5 % of reading + 3 digits)
10  19 1 (5 % of reading)

Measuring resistance........................ approx. 1000 

B.4.2 Calibrated resistances for IMD testing

Test resistance range..................................... 20 k to 650 k(indicative values), 64

steps
Absolute maximum overload voltage............ 265 V

Calculated insulation leakage current

Measuring range (mA) Resolution (mA) Note

0.0 19.9 0.1 calculated value

84
MI 3002 & MI3102 Reduced low voltage supply systems

C Reduced low voltage supply systems

C.1 Standard reference
 BS7671

C.2 Fundamentals
Special supply systems are applied where inherent protection against electric shock is
required but no SELV used. Reduced low voltage supply with ground reference can be
used for this purpose.
There are two options with 110 V nominal voltage.

L1 L1

55 V 63 V
110 V
110 V 110 V
PE 63 V 63 V
55 V L2
110 V
L2 L3
 Single phase with center tap  Three phase star connection, center
connected to PE (i.e. 2 x 55 V). tap connected to PE (i.e. 3 x 63 V).
 No neutral line.  No neutral line.

Figure C.1: General reduced low voltage supply systems

C.3 Measurement guides

The user has to select the reduced low voltage supply system in the instrument before
testing it. The procedure for selecting the reduced low voltage supply system is defined
in chapter 4.5.1 Supply system setup. Once the reduced low voltage system is selected,
the instrument can be used immediately. The instrument keeps selected reduced low
voltage system when it is turned off.

85
MI 3002 & MI3102 Reduced low voltage supply systems

The table below containsEurotest functions intended for test and measurement of
supply systems with compatibility notes related to the reduced low voltage system.

Reduced low voltage system Notes

functions
Contunuity functions
RLOW
Independent of selected supply system.
Continuity
Insulation Independent of selected supply system.
Line resistance
Line resistance Resistance R L1-L2 .
Prospective short circuit
I PSC for U L1-L2 = 110 V.
current
Fault loop resistance
Fault loop resistance Both fault loops, R 1 (L1-PE) and R 2 (L2-PE).
Prospective fault current I SC1 and I SC2 for both fault loops.
Voltage, frequency Symbols modified for reduced low voltage system.
Phase rotation Three-phase system automatic detected.
RCD functions
Contact voltage U C For both posibilities, U 1 (L1-PE) and U 2 (L2-PE).
Trip-out time
Trip-out current Maximum nominal differential current limited to 1 A.
Automatic test
Earth resistance Independent of selected supply system.
PE test probe Disabled.

C.3.1 Voltage

Figure C.2: Example of voltage and frequency measurements

Displayed results for single phase system:

L1-L2 ......Voltage between line conductors,
L1-pe ......Voltage between line 1 and protective conductors,
L2-pe ......Voltage between line 2 and protective conductors.

C.3.2 RCD testing

Maximum regular RCD test current is 1 A r.m.s. (1.4 A peak) and can be achieved only
when fault loop resistance is lower than 1 

Tests are carried out for both combinations (L1-PE and L2-PE) automatically.
Each individual test result is accompanied with appropriate indication.

86
MI 3002 & MI3102 Reduced low voltage supply systems

Figure C.3: RCD contact voltage test

C.3.3 Line resistance and prospective short circuit current

Measured resistance represents Line-Line resistance (R L1-L2 ). Nominal system voltage
for calculation of I PSC is set to 110 V.
Nominal system voltage range for line resistance measurement is 90 V to 121 V. If input
voltage is out of range it is displayed on terminal voltage monitor, together with the
indicator of disabled test .

C.3.4 Fault loop resistance and prospective fault current

The definition of the nominal system voltage for calculating the I PFC changes to:
 55 V for single-phase centre-tap system selected,
 63 V for three-phase system selected.

Tests can be carried out for both combination L1-PE and L2-PE. Each individual test
result is accompanied with appropriate indication.

Nominal input voltages are:

Nominal input voltage U N Voltage range

Single-phase 55 V system (44 V  U  61 V),
Three-phase 63 V system (56 V  U  70 V),

If an input voltage is out of range, it is displayed on terminal voltage monitor together

with the indicator of disabled test .

87
MI 3002 & MI3102 Reduced low voltage supply systems

C.4 Technical specifications

Only those technical specifications are listed below that are different to specifications
from chapter 9 of this document.

C.4.1 RCD testing

C.4.2
C.4.3 General data

Nominal residual current................... 10 mA, 30 mA, 100 mA, 300 mA, 500 mA,
1000 mA
Nominal residual current accuracy.... -0 / +0.1I  ; I  = I N , 2I N , 5I N
-0.1I  / +0; I  = ½I N
Maximum nominal differential
current for declared accuracy ........... 1000 mA for I N
500 mA for 2I N
100 mA for 5I N
Maximum test current ....................... 1 A (for Z LOOP < 1 )
Test current shape............................ Sine-wave (AC), pulsed (A)
DC offset for pulsed test current ....... 6 mA typical
RCD type .......................................... general (G, non-delayed), selective (S, time-
delayed)
Test current starting polarity ............. 00 or 1800
Nominal input voltage ....................... 55 V / 63 V (45 Hz  65 Hz)

C.4.4 Contact voltage

Measuring range according to EN61557-6 is 3.0 V  32.6 V for limit contact voltage 25
V.
Measuring range according to EN61557-6 is 3.0 V  66.0 V for limit contact voltage 50
V.
Measuring range (V) Resolution (V) Accuracy
0.0  9.9 0.1
(-0 % / +15 %) of reading +
2 digits
10.0  99.9 0.1 (-0 % / +15 %) of reading
Accuracy applies for 1 year in reference conditions. Temperature coeficient ouside
these limits is +1 digit.
Test current ...................................... max. 0.5I N
Limit contact voltage ......................... 25 V or 50 V
The contact voltage is calculated to.. I N (general type) or to 2I N (selective type)
UC
Fault loop resistance at contact voltage is calculated as RL  .
I N

88
MI 3002 & MI3102 Reduced low voltage supply systems

Trip-out time
Complete measurement range corresponds to EN61557-6 requirements. Specified
accuracies are valid for complete operating range.

General (non-delayed) RCDs

Measuring range (ms) Resolution (ms) Accuracy
0  300 (½I N , I N ) 1
0  150 (2I N ) 1 3 ms
0  40 (5I N ) 1

Selective (time-delayed) RCDs

Measuring range (ms) Resolution (ms) Accuracy
0  500 (½I N , I N ) 1
0  200 (2I N ) 1 3 ms
0  150 (5I N ) 1

Test current ...................................... ½I N , I N , 2I N , 5I N

5I N is not applicable for I N 100 mA (RCD types AC,A)
2I N is not applicable for I N 500 mA (RCD type AC) or I N 300 mA (RCD type A)
I N is not applicable for I N =1000 mA (RCD type AC) or I N 500 mA (RCD type A)

Trip-out current

Trip-out current (I N =10 mA)

Measurement range corresponds to EN61557-6 requirements. Specified accuracies are
valid for complete operating range.
Measuring range I  Resolution I  Accuracy
0.2I N  1.1I N (AC type) 0.05I N 0.1I N
0.2I N  2.2I N (A type) 0.05I N 0.1I N

Trip-out current (I N 30 mA)

Measurement range corresponds to EN61557-6 requirements. Specified accuracies are
valid for complete operating range.
Measuring range I  Resolution I  Accuracy
0.2I N  1.1I N (AC type) 0.05I N 0.1I N
0.2I N  1.5I N (A type, 0.05I N 0.1I N
I N ≥ 30 mA)

Trip-out time
Measuring range (ms) Resolution (ms) Accuracy
0  300 1 3 ms

Contact voltage
Measuring range (V) Resolution (V) Accuracy
(-0 % / +15 %) of reading +
0.0  9.9 0.1
2 digits
10.0  99.9 0.1 (-0 % / +15 %) of reading

89
MI 3002 & MI3102 Reduced low voltage supply systems

C.4.5 Fault loop resistance and prospective fault current

Rs sub-function
Measuring range according to EN61557-3 is 0.32   1999 .
Measuring range () Resolution () Accuracy*)
0.00  19.99 0.01
20.0  99.9 0.1 (10 % of reading + 5 digits)
100  1999 1
*)
The accuracy is valid if mains voltage is stable during the measurement.

Prospective fault current (calculated value)

Measuring range (A) Resolution (A) Accuracy
0.00  19.99 0.01
20.0  99.9 0.1 Consider accuracy of fault
100  999 1 loop resistance
1.00k  9.99k 10 measurement
10.0  24.4k 100

IPFC calculation................................ I PFC =U N  k SC / Z L-PE

U N = 55 V, (44 V  U  61 V) for selected 55 V single-phase system
U N = 63 V, (56 V  U  70 V) for selected 63 V three-phase system
Test current ...................................... 1.9 A (10 ms)
Nominal input voltage ....................... 55 V / 63 V (45 Hz  65 Hz)
Test posibilities ................................. L1-PE and L2-PE

Rs(rcd) trip-lock sub-function

Measuring range according to EN61557 is 0.85   1999 .
Measuring range () Resolution () Accuracy *)
0.00  19.99 0.01 (10 % of reading + 15 digits)
20.0  99.9 0.1 10 % of reading
100  1999 1 10 % of reading
*)
Acccuracy may be impaired in case of heavy noise on mains voltage.
Prospective fault current (calculated value)
Measuring range (A) Resolution (A) Accuracy
0.00  19.99 0.01
20.0  99.9 0.1 Consider accuracy of fault
100  999 1 loop resistance
1.00k  9.99k 10 measurement
10.0  24.4k 100

IPFC calculation................................ I PFC =U N  k SC / Z L-PE

U N = 55 V, (44 V  U  61 V) for selected 55 V single-phase system
U N = 63 V, (56 V  U  70 V) for selected 63 V three-phase system
Nominal input voltage ....................... 55 V / 63 V (45 Hz  65 Hz)
Test posibilities ................................. L1-PE and L2-PE
No trip out of RCD.

90
MI 3002 & MI3102 Reduced low voltage supply systems

C.4.6 Line resistance and prospective short-circuit current

Line resistance
Measuring range according to EN61557-3 is 0.25   1999 .
Measuring range () Resolution () Accuracy*)
0.00  19.99 0.01
20.0  99.9 0.1 (5 % of reading + 5 digits)
100  1999 1
*)
The accuracy is valid if mains voltage is stable during the measurement.

Prospective short-circuit current (calculated value)

Measuring range (A) Resolution (A) Accuracy
0.00  19.99 0.01
20.0  99.9 0.1
Consider accuracy of line
100  999 1
resistance measurement
1.00k  9.99k 10
10.0  24.4k 100

IPFC calculation................................ I PSC =U N  k SC / Z L-N

U N = 110 V, (90 V  U  121 V)
Test current ...................................... 3.1 A (10 ms)
Nominal input voltage ....................... 110 V (45 Hz  65 Hz)

91
MI 3002 & MI3102 Reduced low voltage supply systems

92